QuakeLoc. Seismic Cable Restraint Connector for piping, duct, electrical cable trays, and suspended equipment. MADE IN THE USA MADE IN THE USA
|
|
|
- Dominick Wilcox
- 6 years ago
- Views:
Transcription
1 MADE IN THE USA MADE IN THE USA MADE IN THE USA MADE IN THE USA QuakeLoc Seismic Cable Restraint Connector for piping, duct, electrical cable trays, and suspended equipment.
2 MADE IN THE USA QuakeKit-P KINETICS QuakeLoc Connector is featured in our new lineup of standard seismic cable restraint systems. Sure to be a contractor favorite, the QuakeLoc connector quickly and easily fastens cables used in the seismic restraint of piping, duct, electrical cable trays, and suspended equipment. QuakeLoc is proudly made in the USA. Seismic Cable Restraint Systems carry tension only loads along the axis of the cable. They are used in pairs 180-degrees apart to restrain pipe, duct, electrical distribution systems or equipment in each axis. Cable restraints provide a load path between the building and the restrained component to ensure that it moves with the building. Bracing is required on both primary axes for all restrained systems. Spacing is determined by the building code and specifying engineer. Cable restraints are required for isolated systems as rigid restraints such as strut will short circuit the isolation. Kinetics QuakeLoc connector is available for purchase as part of Kinetics QuakeKit-P (Pipe), QuakeKit-D (Duct), and QuakeBulk seismic cable restraint systems. Kinetics QuakeKits are competitively priced and offer substantial labor savings when compared to competitors systems. Each kit includes the necessary hardware to connect to suspended components. Hardware to attach QuakeKit systems to concrete, steel or wood structures is also available. QuakeKit Capacities Model Cable Diameter Cable Length Max Cable Tension QuakeKit-P/D-2 QuakeKit-P/D-3 QuakeKit-P/D-4 1/8 in 3/16 in 1/4 in 3 mm 5 mm 6 mm 15 ft 15 ft 15 ft 4.57 m 4.57 m 4.57 m 1000 lbs 2100 lbs 3350 lbs 454 kg 953 kg 1520 kg
3 UAK QuakeKit-D for Duct, Suspended Equipment & Electrical Kinetics QuakeKit-D is specifically designed to provide the necessary components to properly restrain duct, electrical components and suspended equipment. Each prepackaged kit contains: 2 Thimbles 2 15-ft swaged cables 4 KSUA-2 brackets 2 QuakeLoc connectors Suspended Equipment Example Kinetics Isolation Hangers KHRC Rod Stiffener Kit QuakeLoc connector KSUA Cable Attachment Brackets Quake Kit-D
4 E K QuakeKit-P for Piping Building code requires piping to be braced both in transverse and longitudinal directions. Kinetics QuakeKit-P is specifically designed to provide the necessary components to properly restrain a piping system. Each prepackaged kit contains: 2 KSUA-2 brackets 2 Thimbles 2 15-ft swaged cables 2 QuakeLoc connectors 2 KSCA brackets and the necessary hardware to connect to a threaded rod Suspended Piping Example Kinetics Isolation Hangers KHRC Rod Stiffener Kit KSUA Cable Attachment Brackets QuakeLoc connector Quake Kit-P
5 ITS QuakeBulk Kinetics QuakeBulk is a universal kit specially designed for application where more than 15-ft of cable will be required. Bulk cable sold separately. This prepackaged kit contains: 2 KSUA-2 brackets 4 Thimbles 4 QuakeLoc connectors 2 KSCA brackets and the necessary hardware to connect to a threaded rod Attachment Hardware Kinetics offers a wide range of attachment hardware options depending on the situations. Concrete applications require the use of our model KCCAB cracked concrete anchor, model KMTB CMU block anchor or KAABS adhesive anchor. For steel applications, we can provide bolts, nuts and washers or brackets can be welded directly to steel. KCCAB KMTB KAABS QuakeBulk
6 MADE IN THE USA With over 50 years of experience, Kinetics Noise Control has extensive experience in the design, manufacturing and application of innovative products to control sound and vibration. Kinetics pioneered development of precompressed, molded fiberglass pad isolators that would be incorporated into a dynamic new floor isolation system. Kinetics Noise Control now produces the industry s largest selection of inspired products to address vibration and noise control, room acoustics, and seismic restraint concerns for almost any application. Value is added with our experienced team of engineering and customer support personnel ready to work with you. Our experienced staff of over twenty (20) technically trained individuals includes ten (10) licensed Professional Engineers, five (5) holding Master s degrees and two (2) who have earned Ph.D. s. These individuals are spread across Engineering and Manufacturing centers located in Columbus, Ohio (USA), Toronto, Ontario (Canada) and Hong Kong (China). Their combined experience spans over 400 years! Noteworthy Projects Lou Ruvo Brain Institute, Las Vegas NV Indu and Raj Soin Medical Center, Beavercreek, OH Burj Khalifa Tower Dubai New Quito International Airport, Quito, Ecuador City of Dreams / Grand Hyatt, Macau Microsoft headquarters, Beijing Victoria Harbour Tunnel Project, Hong Kong The Venetian Hotel and Casino, Macau City Center, Las Vegas, NV River Oak Hospital, Jackson MS Roper St. Francis, Charleston, SC Kaleida Healthcare, Buffalo, NY Syracuse VA Hospital, Syracuse, NY Dublin Methodist Hospital, Dublin, OH St. Anthony s Medical Center, St. Louis, MO McCarren Airport, Las Vegas, NV American Snuff Company, Memphis, TN Duke Medical Center, Durham, NC Filmore Hospital, Genera, NE ECMC Kidney Care, Buffalo, NY Columbia College, Hamilton, Ontario Hamilton Health Science Building, Hamilton Ontario Toronto Police Station, Toronto, Ontario kineticsnoise.com/quakeloc sales@kineticsnoise.com MADE IN USA Kinetics Noise Control, Inc. is continually upgrading the quality of our products. We reserve the right to make changes to this and all products without notice. QUAKELOC 02/12
KINETICS Pipe & Duct Seismic Application Manual
QUICK START READ ME FIRST I1.1 Seismic Restraint Categories and Types: Seismic restraints for pipe and duct are generally separated into to two categories. 1. Transverse Seismic Restraints: These act to
SEISMIC RESTRAINT SYSTEM
1. GENERAL 1.1. Description: SECTION 16012 SEISMIC RESTRAINT SYSTEM 1.1.1. This specification covers design and installation of seismic bracing and anchorage required for conduit, cable tray, bus duct,
Seismic Restraint Capabilities
KINETICS NOISE CONTROL Seismic Restraint Capabilities Why is Seismic Restraint needed? The damaging effects of earthquakes are of significant concern in many areas of the world. Earthquake damage to inadequately
KINETICS Pipe & Duct Seismic Application Manual
I8. Why are Stiffeners Needed? rod stiffeners are used to prevent the buckling of the hanger rods under the compressive reaction loads during an earthquake. Buckling is very difficult to predict, and depends
Project No
PART 1 - GENERAL 1.1 SECTION INCLUDES A. Seismic Requirements for single rod hanger supports for conduit, pipe and other similar systems. B. Seismic Requirements for trapeze type supports for cable tray,
KINETICS Pipe & Duct Seismic Application Manual
S8.1 Introduction: During an earthquake, the hanger rods are not passive components that just simply support the dead load of the pipe or duct. They must also resist the reaction forces generated by the
KINETICS Pipe & Duct Seismic Application Manual
SELECTION & LOCATION OF RESTRAINTS FOR PIPE AND DUCT S7.1 Introduction: The actual selection of the seismic restraints and the approximate locations for those restraints along the pipe or duct has typically
KINETICS Pipe & Duct Seismic Application Manual
S1.1 Introduction: As with any task in the design and construction of buildings, there are certain terms, definitions, and standards of practice that must be understood and employed in order to maintain
KINETICS TM. Restrained Spring Isolators Model FLSS 1 and 2
KINETICS TM Restrained Isolators Model FLSS 1 and 2 Description Kinetics Model FLSS Seismic Control Restrained Vibration Isolators consist of free-standing, large diameter, laterally stable steel springs
Table of Contents... 1, 2. (EF) Equipment Floor... VISR EF 102 Water Heater VISR EF 104 Chiller VISR EF 105 End Suction Pump...
VISR Standard Details - TOC VISR-SD File No: T-VISR-SD-00 Supersedes: New Date: 6-Mar-204 Date: New VISR Standard Details: Table of Contents Table of Contents..., 2 (EF) Equipment Floor... VISR EF 0 Tank...
KINETICS Seismic & Wind Design Manual Section D9.0
KINETICS Seismic & Wind Design Manual Section D9.0 SECTION D9.0 TABLE OF CONTENTS Title Revision Record Section D9.0A D9.0 Electrical Distribution Systems Title Section Seismic Forces Acting On Cable Trays
KINETICS Pipe & Duct Seismic Application Manual
Introduction: Determining the actual rod stiffener requirements for a specific hanger location on a specific project is beyond the scope of this manual. However, the intent of this appendix is to demonstrate
BRANZ FACTS RESILIENT NON-STRUCTURAL ELEMENTS SEISMICALLY RESILIENT NON-STRUCTURAL ELEMENTS # 3. Restraint systems
SEISMICALLY BRANZ FACTS RESILIENT NON-STRUCTURAL ELEMENTS SEISMICALLY RESILIENT DESIGN CRITERIA # 2 NON-STRUCTURAL ELEMENTS # 3 Restraint systems The next step in the non-specific design pathway in NZS
Seismic Installation Manual
Seismic Installation Manual This manual provides the design strength capacities and installation guidelines for the Restraint systems brace components for use in the design of an overall bracing/restraint
SECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 260548 - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Isolation pads. 2. Spring isolators. 3. Restrained spring isolators. 4. Channel
DIVISION 20 GENERAL SECTIONS FOR PLUMBING, FIRE SUPPRESSION & HVAC SECTION VIBRATION ISOLATORS
DIVISION 20 GENERAL SECTIONS FOR PLUMBING, FIRE SUPPRESSION & HVAC SECTION 20 05 80 PART 1 GENERAL 1.01 DESCRIPTION A. Provide a complete vibration isolation system to isolate motorized equipment, piping,
Large cable sizes stronger than pipe/strut
Legrand Seismic Wire Rope/Cable Bracing is the recommended seismic bracing for Legrand wire mesh and ladder tray systems. It is UL Listed, complies with all building codes and standards, and offers significant
2005 Seismic Bracing System. Superstrut Metal Framing
2005 Seismic Bracing System Superstrut Metal Framing What is Seismic Bracing? Seismic Bracing is support systems that account for forces generated by an earthquake Vertical Pipes or Duct hanging overhead
SRS-02 NEW SEISMIC RESTRAINTS. Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems SYSTEMS THAT MAKE SENSE
NEW SRS-02 SEISMIC RESTRAINTS Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems OSHPD Pre-Approved System SYSTEMS THAT MAKE SENSE INTRODUCTION INTRODUCTION What
2005 Seismic Bracing System. Kindorf Modular Metal Framing
2005 Seismic Bracing System Kindorf Modular Metal Framing What is Seismic Bracing? Seismic Bracing is support systems that account for forces generated by an earthquake Vertical Pipes or Duct hanging overhead
SECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions, apply to this Section. 1.2 SUMMARY A. This Section includes the
SEISMIC RESTRAINTS Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems
SEISMIC RESTRAINTS Multi-Directional Bracing For Electrical Conduit, Cable Tray And Mechanical Piping Systems SYSTEMS THAT MAKE SENSE INTRODUCTION INTRODUCTION What is Seismic Bracing? Seismic forces are
Seismic Restraints. Cent-R-Rail Supplement* SYSTEMS THAT MAKE SENSE
SRSCR-0 Seismic Restraints Cent-R-Rail Supplement* Multi-Directional Bracing For Data-Track, Half-Rack and Multi-Tier Half-Rack Systems Structural Engineer S 9 *To be used in conjunction with Cooper B-Line
SECTION VIBRATION CONTROLS FOR PLUMBING PIPING AND EQUIPMENT
Page 220548-1 SECTION 220548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
SECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - VIBRATION AND SEISMIC CONTROLS FOR HVAC PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
SECTION SEISMIC CONTROL OSHPD
SECTION 01451 PART 1 - GENERAL 1.01 DESCRIPTION A. Provide all required seismic restraints and calculations in order to insure that the installation of all architectural, mechanical, and electrical equipment/components
Student Services & Classroom Addition SECTION VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 26 05 48 - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Isolation pads. 2. Spring isolators. 3. Restrained spring isolators. 4. Channel
NATIONWIDE SAN ANTONIO SALES & SERVICE CENTER
SECTION 21 05 31 SEISMIC CONTROLS AND WIND RESTRAINTS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Not Applicable 1.02 SUMMARY A. This section includes the design, application and installation of seismic and
KINETICS Pipe & Duct Seismic Application Manual
KINETICS ipe & Duct Seismic Application Manual FIRE ROTECTION IING SYSTEMS S13.1 Introduction: Historically the ICC (2000, 2003, 2006, and 2009 IBC) and the NFA (NFA 5000) have been competing code writing
SECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
Page 230548-1 SECTION 230548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
SUMMARY OF ADDENDUM NUMBER FOUR
SUMMARY OF ADDENDUM NUMBER FOUR Date: June 6, 2013 Owner: Rockcastle County Project Name: Rockcastle County Emergency Operations Center This addendum is issued to modify, explain or amend the original
SECTION VIBRATION ISOLATION
SECTION 23 05 48 VIBRATION ISOLATION PART 1 - GENERAL 1.1 SECTION INCLUDES A. Bases. B. Vibration Isolation. C. Flexible Connectors. 1.2 SUBMITTALS A. Submit shop drawings per Section 23 05 00 and the
SEISMIC CONTROL MEASURES By Richard Lévesque, ing., P.Eng., LEED AP
SEISMIC CONTROL MEASURES By Richard Lévesque, ing., P.Eng., LEED AP Outline What and Why of Seismic Restraint Applicable Codes & Standards for Seismic Restraint Where and When of Seismic Restraint General
KINETICS Seismic & Wind Design Manual Section D3.0
KINETICS Seismic & Wind Design Manual Section D3.0 SECTION D3.0 TABLE OF CONTENTS Title Revision Record Section D3.0A D3.0 Product/Design Overview Title Section The Biggest Problems for Contractors Have
SECTION VIBRATION ISOLATION
SECTION 15240 VIBRATION ISOLATION PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 15450 - Plumbing Equipment. 2. 15510 - Piping (HVAC). 3. 15515 Valves, Hangers, and Specialties. 4. 15540 - Pumping
NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 0548 - PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
SECTION (16071) - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS
SECTION 26 05 48 (16071) - VIBRATION AND SEISMIC CONTROLS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.01 SUMMARY A. This Section includes seismic restraints and other earthquake-damage-reduction measures for
C. OSHPD: Office of Statewide Health Planning and Development for the State of California.
SECTION 21 05 48 VIBRATION AND SEISMIC CONTROLS FOR FIRE-SUPPRESSION PIPING AND EQUIPMENT PART 1 - GENERAL 1.01 INTENT A. It is the intent of this Specification to provide a basis of design for the vibration
Houston First Corporation Package 1
SECTION 260548 VIBRATION CONTROLS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
SECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Elastomeric Isolation pads. 2. Elastomeric Isolation mounts. 3. [Freestanding] [Restrained] [Freestanding and restrained]
Super-Compact Ceiling Hanger Model KSCH Patent Pending Ceiling Isolation Theory: Resiliently suspended ceiling systems are designed to minimize floor impact noise and airborne sound transmissions through
Seismic Installation Manual
Seismic Installation Manual This manual provides the design strength capacities and installation guidelines for the Bracing System for use in the design of an overall bracing system for suspended nonstructural
THE RSIC SOUND ISOLATION CLIPS. RSIC-WFI (Wall Frame Isolator)
LOWEST LABOR COST HIGH PERFORMANCE WALL ISOLATION WOOD STEEL CONCRETE CMU CONDOS TIME SHARE / FRACTIONAL OWNERSHIP ASSISTED LIVING APARTMENTS HOTELS / MOTELS SINGLE FAMILY HOMES HOME THEATER COMMERCIAL
Kinetics Noise Control
Kinetics Noise Control Acoustical Curtain Systems www.kineticsnoise.com Acoustical Curtain Systems Kinetics Noise Control s acoustical curtain systems are custom engineered to your application for acoustic
REV. 9/08. Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms
REV. 9/08 Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms SKYTRON MOUNTING STRUCTURES for Ceiling Mounted Equipment Foreword Skytron s objective is to provide a program and guideline to assist
Cantilevered Rail System
Knight Global's Cantilevered Rail Systems are designed to eliminate the need for a four post floor structure system. It provides an alternative to workstations with minimal floor space. A wide range of
ADDENDUM NUMBER 10 TO THE PLANS AND SPECIFICATIONS FOR
ADDENDUM NUMBER 10 TO THE PLANS AND SPECIFICATIONS FOR FOR LAWTON PUBLIC SCHOOLS FREEDOM ELEMENTARY SCHOOL Architect s Project Number: N09017 ARCHITECTURE PLANNING INTERIORS Date: 04.16.13 The following
Cable Bracing Systems.
Cable Bracing Systems www.grippleseismic.com Gripple Seismic Bracing Systems Introduction Gripple Seismic Restraint Systems are specifically designed and engineered to brace and secure nonstructural equipment
SECTION HANGERS AND SUPPORTS FOR PLUMBING
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
FEDERAL EMERGENCY MANAGEMENT AGENCY FEMA 414/January 2004 INSTALLING SEISMIC RESTRAINTS FOR DUCT AND PIPE
FEDERAL EMERGENCY MANAGEMENT AGENCY FEMA 414/January 2004 INSTALLING SEISMIC RESTRAINTS FOR DUCT AND PIPE Notice: This guide was prepared by the Vibration Isolation and Seismic Control Manufacturers Association
SECTION HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS
SECTION 26 05 29 HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 GENERAL 1.1 DESCRIPTION A. Scope: 1. CONTRACTOR shall provide all labor, materials, equipment, and incidentals as shown, specified, and
Retrofit Measures for Superstructures, Bearings, and Seats
Retrofit Measures for Superstructures, Bearings, and Seats Presented by Richard V Nutt Elements to be Retrofitted Bridge Decks and Girders Bearings, Anchorages and Pedestals Expansion Joints 1 Elements
MEP21252 Revit Plug-in: Automated Hanger and Seismic Bracing Layout and Design for MEP Systems
MEP21252 Revit Plug-in: Automated Hanger and Seismic Bracing Layout and Design for MEP Systems Alan Espinoza MMC Contractors Jake Olsen, PE DEWALT Learning Objectives Learn how Revit can be used to efficiently
SECTION VIBRATION AND SEISMIC CONTROL FOR PLUMBING
SECTION 22 05 48 VIBRATION AND SEISMIC CONTROL FOR PLUMBING PART 1 - GENERAL 1.1 SUMMARY A. Section includes inertia bases, vibration isolation, acoustic housings, and for plumbing equipment. 1.2 PERFORMANCE
C. Concrete Inertia Bases: Drawings showing required concrete steel reinforcing, construction details, and dimensions.
15240 VIBRATION ISOLATION ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 230548 An optional keynote
Seismic Installation Manual
Seismic Installation Manual California Office of Statewide Health Planning & Development OPA-2123-10 This manual provides the design strength capacities and installation guidelines for the Bracing System
SUPPORT AND ANCHORS SECTION 15090
SUPPORT AND ANCHORS SECTION 15090 PART 1 GENERAL 1.1 DESCRIPTION OF WORK A. Work included in this Section: Materials, equipment, fabrication, installation and tests in conformity with applicable codes
DARTMOUTH COLLEGE DESIGN September 15, 2004 &CONSTRUCTION GUIDELINES
PART 1 DESIGN DIRECTIVE 1.1 RELATED DOCUMENTS SECTION 15240 SEISMIC RESTRAINT AND VIBRATION CONTROL A. This section shall be considered as a part of each DC Standards, Part 15. 1.2 QUALITY ASSURANCE A.
SEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets
SEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets Seismic Frame Two-Post Rack Page 11-3 Seismic Protection Products - Racks Page 11-6 Seismic Protection Products - Runway Page 11-8 Seismic
SECTION NON-STRUCTURAL SEISMIC DESIGN CRITERIA PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 014100 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
SEISMIC EXPECTATIONS
SEISMIC EXPECTATIONS John Callea Manager Professional & Advisory Services Department Planning, Transport & Infrastructure What tonight's about, Earthquake Risk DPTI Expectations Seismic Compliance Ministers
SECTION NOISE AND VIBRATION CONTROL FOR HVAC PIPING AND EQUIPMENT
SECTION 23 05 41 PART 1 - GENERAL 1.1 DESCRIPTION SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph
Concrete Inserts. B Adjustable Metal Deck Ceiling Bolt
B3019 - Adjustable Metal Deck Ceiling Bolt Size Range: 3 /8"-16 thru 3 /4"-10 rod Function: For use in metal deck formed concrete to attach hanger rods. Allows for pre-positioning of hanger rods in poured
Suggested Materials and Tools:
NOISE CONTROL RESILIENT CEILING WAVE HANGER (Worldwide Patents Pending) INSTALLATION GUIDELINES Suggested Materials and Tools: Kinetics Noise Control CPT resilient tape for perimeter of room 0.875 tall
Compression Superstructure TELETOM 500/700 Series Equipment Management Booms TELETOM 400/600 Series Anesthesia Booms
Contractor s Summary for Compression Superstructure TELETOM 500/700 Series Equipment Management Booms TELETOM 400/600 Series Anesthesia Booms Document # 70-000-00195 rev 01! WARNING This summary dimensional
Materials Carbon Steel is used in the manufacturing of riser and pipe clamps. Stainless Steel and other materials are available.
Pipe clamps offered in this section are designed for support and attachment of pipe to structural members. wide range of pipe clamps are available for various applications. Materials arbon Steel is used
MEP Seismic & Wind Provisions of ASCE Prepared for the 2017 Rochester Engineering Symposium Richard Sherren, P.E.
MEP Seismic & Wind Provisions of ASCE 7-10 Prepared for the 2017 Rochester Engineering Symposium Richard Sherren, P.E. 1 New York State Model Building Code The state of New York has adopted the 2015 International
Modular/Restraint Isolator
Modular/Restraint Isolator Model U.S. Patent No. 7,,9 Description Designed for the latest building codes, the Kinetics Model Seismically Rated Restraint/Vibration Isolator can be used as a restraint device
Fig Beam Clamp Retaining Strap (B-Line B3367)
Fig. 69 - Beam Clamp Retaining Strap (B-Line B3367) Size Range: 3 /8"-16 thru 3 /4"-10 rod 4 (101.6mm) thru 16 (406.4mm) lengths Note: longer lengths are available consult factory Material: Pre-Galvanized
SERIES SURGICAL LIGHTS
SERIES SURGICAL LIGHTS TEC-B-0012 REV1 Skytron's Aurora LED Surgical Lighting provides advanced bright, cool and color correct illumination to the surgical field and a selectable color temperature of 4,000K
SECTION VIBRATION AND SEISMIC CONTROLS FOR HVAC EQUIPMENT
SECTION 23 05 48 VIBRATION AND SEISMIC CONTROLS FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Work included: Provision of materials, installation and testing of: 1. Vibration Isolation 2. Seismic Restraint
SECTION SEISMIC RESTRAINT REQUIREMENTS FOR NON-STRUCTURAL COMPONENTS REVISED PART 1 GENERAL 1.1 DESCRIPTION:
SECTION 13 05 41 SEISMIC RESTRAINT REQUIREMENTS FOR NON-STRUCTURAL COMPONENTS REVISED 1-25-13 PART 1 GENERAL 1.1 DESCRIPTION: A. Provide seismic restraint in accordance with the requirements of this section
Pipe Riser Isolation Selection Guide
Pipe Riser Isolation Selection Guide kineticsnoise.com Vibration Isolators as Pipe Riser Supports Vertical pipe risers can create a unique set of problems when they are installed in multistory buildings.
SERIES SURGICAL LIGHTS
SERIES SURGICAL LIGHTS TEC-B-0012 REV1 Skytron's Aurora LED Surgical Lighting provides advanced bright, cool and color correct illumination to the surgical field and a selectable color temperature of 4,000K
ARCHITECTURAL CEILING HANGERS
, Inc. Manufacturers of Vibration Control Products 350 Rabro Drive 2101 W. Crescent Ave., Suite D Hauppauge, NY 11788 Anaheim, CA 92801 631/348-0282 714/535-2727 FAX 631/348-0279 FAX 714/535-5738 Info@Mason-Ind.com
SPECIFICATION & DESIGN MANUAL " AISI 1060 to 1065 Rockwell Hardness 51 to 55 Perma-Seal coated Stick-E Pin 3/4" (Step Shank) 1"
Trak-It /Stick-E TM SPECIFICATION & DESIGN MANUAL TM Stick-E Electrical and Mechanical Fastening System PRODUCT DESCRIPTION The Stick-E fastening system uses Trak-It gas technology with specially designed
Suggested Materials and Tools:
NOISE CONTROL RESILIENT CEILING WAVE HANGER (Worldwide Patents Pending) INSTALLATION GUIDELINES Suggested Materials and Tools: Kinetics Noise Control CPT resilient tape for perimeter of room 0.875 tall
Materials Carbon Steel and Malleable Iron are used in the manufacture of concrete inserts. Stainless Steel and other materials are available.
Concrete inserts offered in this section are designed to provide a pre-set support point in concrete ceilings, walls, and floors. A range of inserts with varying design loads are available. Materials Carbon
ADJUSTABLE PIPING SUPPORT PRODUCT BROCHURE
ADJUSTABLE PIPING SUPPORT PRODUCT BROCHURE OVERVIEW REVOLUTIONARY VERSATILE EFFICIENT The Roof Top Blox is a revolutionary roof top support block system that works with height extension rods, securing
ADJUSTABLE PIPING SUPPORT PRODUCT BROCHURE
ADJUSTABLE PIPING SUPPORT PRODUCT BROCHURE OVERVIEW REVOLUTIONARY VERSATILE EFFICIENT The Roof Top Blox is a revolutionary roof top support block system that works with height extension rods, securing
JMG CONSULTANTS, INC.
SEISMIC ANALYSIS FOR THE RESTRAINT OF CEILING HUNG FIRE PROTECTION PIPING WITH SOLID ARM BRACING DWGS.: SP-01, SP-2, SP-3, SP-4, & SP-5 JAY M. GUERIN LICENSED PROFESSIONAL ENGINEER NEW YORK LICENSE NUMBER
Summary of Modifications/Changes in this Update
Summary of Modifications/Changes in this Update This Summary of Changes is for information only. It is not a part of the referenced document, and should not be used for project documentation. U.S. Department
Suspension System Data Center Ceiling Solutions
Hardware That Needs to be Purchased Separately Screws are fine listed as shown: Min 1-1/4" or longer #8 Truss head self-tapping screws for attaching structural wall angle, lateral support bar 16" or 4"
HAMBRO COMPOSITE FLOOR SYSTEM
HAMBRO COMPOSITE FLOOR SYSTEM OUR EXPERTISE AT YOUR SERVICE Canam has been offering owners, real estate developers, architects, engineers and contractors an array of construction solutions since 1970.
SECTION HANGERS AND SUPPORTS FOR PLUMBING PIPING AND EQUIPMENT
Page 220529-1 SECTION 220529 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
PRELUDE. 24 MAX TM Suspension System Data Centre Ceiling Solutions. Assembly and Installation Instructions
Hardware That Needs to be Purchased Separately Screws are fine listed as shown: 4. x 3 mm or longer Self Drilling Screw Phillips Pan Head for attaching structural wall angle, lateral support bar 400 mm
SECTION VIBRATION ISOLATION FOR PLUMBING PIPING AND EQUIPMENT
SECTION 220550 - VIBRATION ISOLATION FOR PLUMBING PIPING AND EQUIPMENT PART 1 - GENERAL REQUIREMENTS 1.1 SUMMARY A. It is the intent of this specification to provide vibration isolation supports for Plumbing
DURA-BLOK rooftop supports BRTS-13 DURA-BLOK. A complete rooftop support solution
DURA-BLOK rooftop supports BRTS-13 DURA-BLOK A complete rooftop support solution DURA-BLOK rooftop solutions support DURA-BLOK supports are made of 100% recycled rubber and are designed to provide an economical
BSR E XX DRAFT Rig/ r3. BSR E1.4-2, Entertainment Technology Statically Suspended Rigging Systems.
BSR E1.4-2, Entertainment Technology Statically Suspended Rigging Systems Table of Contents 1 GENERAL... 2 1.1 Scope... 2 1.2 Purpose... 2 1.3 Application... 2 1.4 Alternative materials, design and methods
Fig. 1 - Standard Clevis Hanger
Revision 10/24/2007 Fig. 1 - Standard Clevis Hanger Component of State of California OSHPD Approved Seismic Restraints System Size Range Size 1/2" thru 36" pipe. Function Recommended for the suspension
Don t leave your seismic compliance to chance
Seismic bracing SEISVP-13R Don t leave your seismic compliance to chance Rely on B-Line support from pre-bid to inspection Don t leave your seismic compliance to chance Rely on B-Line support from pre-bid
NZS 4219:2009 Seismic performance of engineering systems in buildings
Skip to main content Skip to primary navigation Home Home About this portal Latest updates Menu Print Save Email Resource detail Citations NZS 4219:2009 Seismic performance of engineering systems in buildings
B-LINE SERIES. DURA-BLOK rooftop supports BRTS-17 DURA-BLOK. A complete rooftop support solution
DURA-BLOK rooftop supports BRTS-17 B-LINE SERIES DURA-BLOK A complete rooftop support solution DURA-BLOK rooftop solutions support DURA-BLOK supports are made of 100% recycled rubber and are designed to
Bracing Systems. Available At VIKING SA Tel: (+352) Fax: (+352)
Bracing Systems Available At VIKING SA Tel: (+352) 58-37-37-1 Fax: (+352) 58-37-36 Email: vikinglux@vikingcorp. Bracing Systems To help ensure the availability and operation of safety systems after an
PRE-INSTALLATION GUIDE
TRUMPF MEDICAL SYSTEMS Inc. Charleston, SC PRE-INSTALLATION GUIDE FOR CEILING MOUNTED EQUIPMENT MANAGEMENT SYSTEMS, SURGICAL / EXAM LIGHTS, AND FLAT PANELS EMS and Light Pre-installation Guide File: 110720
OSU PROJECT NO PAGE 1 02 NOV 2006 SECTION SUPPORTS AND ANCHORS
OSU PROJECT NO. 30-04-15 PAGE 1 PART 1 GENERAL 1.1 WORK INCLUDED A. Supports and anchors for piping systems and equipment. 1.2 RELATED WORK SPECIFIED ELSEWHERE A. The provisions of Section 15050, Basic
DURA-BLOK Rooftop Supports
Cooper B-Line s new line of DURA-BLOK products gives you a versatile and long-term solution for all your roof top support needs. Designed with flexibility in mind, Dura-Blok is ideal for roof top support
A. This Section includes steel cable trays and accessories.
SECTION 26 05 36 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
Residential Deck Safety, Construction and Repair. Juneau Permit Center, 4 th Floor Marine View Center,(907) February 2016
February 2016 Residential Deck Safety, Construction and Repair Juneau Permit Center, 4 th Floor Marine View Center,(907)586-0770 This handout is designed to help you build your deck to comply with the
Garage Beam System DAYTONSUPERIOR.COM FORMING. For Post-Tensioned Beam and Slab Parking Structures
Garage Beam System For Post-Tensioned Beam and Slab Parking Structures FORMING The Garage Beam System is a complete forming system designed specifically for post-tensioned beam and slab multi-story parking