Air Duct Metal Products

Transcription

1 Quality Sheet Metal Products Since 1985 Air Duct Metal Products Commitment to Excellence Our customers depend on us for a superior product and reliable delivery, a responsibility we take very seriously. ADMP maintains strict quality control in every aspect of its manufacturing process. We stay with a job from the pre-planning stages to a certified inspection of the completed project, if requested. We believe in providing cost-effective solutions for Contractors, Architects, Supply Houses, Mechanical Engineers, City Engineers and owners alike. Our products afford efficiency on the job and lower the cost of expensive man-hours, while maintaining or improving job-quality. Give us a call and find out why our commitment to excellence, both in product and customer service, sets the standard in the industry. Sincerely, Jay Khawaja Vice President ADMP O: C: jay@admp.us A

2 Table of Contents: Section Product I. Round - Single Wall Standard II. III. IV. Round - Double Wall Standard Round - Specialty Items Rectangle - Single Wall V. Rectangle - Double Wall VI. Residential B

3 Our Products With more than 30 years in business, ADMP prides itself on delivering the very best quality product available on the market. We bring the same exacting level of commitment to every job, no matter how big or small. The results speak for themselves 1) Superior Product 2) Competitive Prices and 3) Quick Delivery-Guaranteed. ADMP offers a complete line of galvanized products including rectangular, round, acoustical pipe, dust collection systems and pre-fabricated duct and fittings. Spiral Duct Spiral Pipe and Fittings Spiral Galvanized pipe has proven to be the ultimate in pressuretype circular tubes. Spiral pipe has a smooth interior for low friction loss. Our spiral Pipe comes with an advanced 4-ply locking seam, resulting in both added rigidity, higher strength and greater durability during the installation process Manufactured on our State-of-theArt Betech spiral machine, this pipe has been used in applications ranging from air conditioning to life support systems; inclusive of critical applications such as radioactive and contaminated fume control. For accuracy and uniformity, the metal seams are held to a tollerance of +/-.006 of an inch. Load Specifications per lin. ft. #1 Standard lbs lbs # 2 Corrugated lbs In addition every galvanized coupling meets the specifications of SMACNA for both high and lowvelocity work. For additional strength underground, our spiral, 14 and larger is corrugated giving a 300% increase in load carrying capacity. You ll find the same high standards and quality built into each of our fittings. Virtually every angle is available with tees, laterals, reducers or couplings built to the same rigid specifications. We can also assist and provide special fitting to fitting configurations, which eliminate the necessity of extra couplings. 1.0

4 Fittings Low and Medium Pressure Fittings Made from extremely accurate patterns, these fittings are electrically cut with shouldered welded seams, then spot-welded along the entire seam. These fittings also come in virtually every angle, with standard and special fittings available on request. Standard sizes for elbows, reducers and couplings include 90, 60, 45, and 30. Standard fittings also come with couplings built into the ends for easier installation. High Pressure Fittings High-Pressure fittings come with a lapping seam in the direction of air flow. These fine, continuous-welded seams are made with metal inert gas (MIG) shielded welds as detailed in the SMACNA 2005, 3rd edition manual. The ends are made with a two-inch male sleeve with stop beads. Available Sizes: 4 to 64 Gauges: 26 to 18 Specialty Fittings Configurations Specialty fittings are available, on request, to fit your projects specific needs. 1.1

5 Spiral Pipe Galvanized ADMP s spiral pipe, the ultimate in pressure tight circular tubes of superior quality, are fabricated in exact sizes using galvanized steel. The pipe consists of a smooth interior for low friction loss and a 4 ply spiral lockseam entirely on the outside for high strength and rigidity. Commonly produced for air conditioning systems as well as critical installations including ventilation, automobile exhaust, and dust collection systems. Usage: Couplings conform to all specifications of the SMACNA rd edition manual, (unless otherwise specified) as recommended for (2-10 W.G. Positive Static Pressure). Seam metal is held to plus or minus.006 of an inch. ADMP s spiral pipe will meet or exceed the gauges listed in the SMACNA 2005, 3rd edition manual. Sizes: 4-10 are available in 1 inch increments are available in 2 inch increments Hydrostatic Pressures Hydrostatic pressures to seam failure - All pressures in lbs. per square inch. Diameter gauge gauge gauge Diameter Material Thickness ASTM Type Length 4-64 Galvanized Ga. A-653 G60 OR G , 10 Standard 4-64 Paint Grip Ga. A-653 A , 10 Standard 4-64 Aluminum B H , 10 Standard 4-64 Stainless Steel Ga. A OR , 10 Standard Long Seam Pipe Solid Welded Lapped Seam shall be provided in 4 foot lengths. Gauges are as listed in the SMACNA HVAC Duct Construction Standards Metal and Flexible - 3rd Edition - Table 3-5. Diameter Gauge ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

6 Standard Duct Fittings Round There are fittings available for virtually every application. Taper-type Reducers, Elbows to 90, Couplings, Tees, Laterals-we have them all. Machine cut for accuracy using precision patterns, fittings go together fast. (Custom fittings available upon request) Gauges: 26 to 18 Available Sizes: 4 to 64 3, 5, 7 pc 90 Elbow 2, 3, 4 pc 45 Elbow 3, 5, 7 pc 75 Elbow 2, 3, 4 pc 30 Elbow 2, 3 pc 60 Elbow End Cap Double Y Branch with Equal Branches Double Y Branch with Un-Equal Branches End Plug Coupling Straight Offset Straight Concentric Reducer Straight 45 Lateral 45 Lateral with a Concentric Reducer 45 with an Eccentric Reducer Concentric Reducer with a 45 Lateral Eccentric Reducer with a 45 Lateral Easy Flow 45/90 Easy Flow 45/90 with a Concentric Reducer Easy Flow 45/90 with an Eccentric Reducer Easy Flow 45 Lateral Easy Flow 45 Lateral with a Concentric Reducer Easy Flow 45 Lateral with an Eccentric Reducer Straight 90 Tee 90 Tee with a Concentric Reducer Concentric Reducer with a Straight 90 Tee 1.3 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

7 90 Tee with an Eccentric Reducer Straight Conical Tee Conical Tee with a Concentric Reducer Single Boot Tee Double Boot Tee Single Boot Tee with a Concentric Reducer Double Boot Tee with a Concentric Reducer Straight 90 Conical Cross Straight 90 Conical Cross with a Concentric Reducer Straight 90 Cross with a Flat on the Top Concentric Reducer with a 45 Lateral Cross 45 Lateral Cross 45 Lateral Cross with a Concentric Reducer Straight 90 Tap-In Flange Easy Flow 45 Tap-In Flange Straight 45 Tap-In Flange Straight Conical Tee Tap-In Flange Easy Flow 45/90 Tap-In Flange Straight 90 Cross Straight 90 Cross with a Concentric Reducer Additional Poly-Coated Fittings Concentric Reducer with a Straight 90 Cross Saddle Boot Boot (residence type) ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

8 Low Pressure Fittings, Round These superior round fittings are made from accurate fitting patterns electrically cut with good shouldered seams. Usage: These very strong seams are designed for low-pressure air systems and may be used ABOVE ground or UNDER ground when embedded in concrete. Couplings are built into the ends of the fittings. Types of Fittings: All standard fitting sizes and shapes are available. 90, 60, 45 and 30 degree elbows are standard. Other angles are available on special order. Tees, lateral (45 degree branch), reducers, and couplings are standard. For elbows, a centerline radius of one times the diameter is standard. 1-1/2 times the diameter (full radius) and 2 times the diameter (long radius) are available. We can also make other size radii and other fittings as specified. Sizes and Gauges: 4-10 are available in 1 inch increments are available in 2 inch increments ADMP s low pressure fittings will meet or exceed the gauges listed in the SMACNA 2005, 3rd edition manual. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. 1.5 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

9 Medium Pressure Fittings for Galvanized Round A wide variety of round fittings are produced by ADMP for medium pressure including 90, 60, 45, and 30 degree elbows, tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. Fitting ends are made with two inch male sleeves. Standard fittings have built-in slip type beaded couplings. Gores & Seams: Lapping of seams are in the direction of air flow. The gores and seams are spot welded and internally sealed using medium pressure duct sealant. Gores Elbow Fitting Gauge 5 piece 90 degrees piece 60 degrees piece 45 degrees For elbows, a wide variety of different radii are available; one and one-half diameter to centerline is standard. Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a rounded entrance edge. They are not butt welded square entrance contractor type fittings. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table assuring manufacturing tolerance consistency. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

10 High Pressure Fittings for Galvanized Round A wide variety of round fittings are produced for high pressure including 90, 60, 45 and 30 degree elbows, tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. Fitting ends are made with two inch male sleeves. Standard fittings have built-in slip type beaded couplings. Gores & Seams: Lapping of seams are in the direction of air flow. The gore & seams are spot welded sand internally sealed using high pressure duct sealant. Gores Elbow Fitting Gauge 5 piece 90 degree piece 60 degree piece 45 degree Fitting ends are made with two inch male sleeves with a stop-bead up to 36 diameter. Radius: 1-1/2 times the diameter (long radius) to centerline is standard Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a rounded entrance edge. They are not butt-welded, square-entrance contractor-type fittings. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), wide variety of different radii are available Flange connections are available by the following, but not limited to: Angle Rings or, AccuDuct, Spiral Mate Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. 1.7 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

11 Acoustically Lined K-2775 High Pressure Duct Combining the acoustical advantages of lined duct with the permanence of a galvanized steel liner, K-2775 comes with a K factor of.27 Btu/Hr./Sq. Ft./ F at 75 Fahrenheit mean temperature. Fitting seams are continuous welded MIG welds, with a silicon bronze wire and Argon shielding. With a sound rating similar to United K-27 duct, K-2775 features lining perforations of 3/32 diameter, with no more than a 23% free area. To ease installation, all fittings have couplings with stop beads built into their construction; liners are built with an extended coupling to aid field assembly. Gauges of Metal Size Duct Fittings Inside Diameter Outer Inner Outer Inner liner liner

12 Double Wall Round Spiral Duct Double wall round spiral duct has two different types of applications: Acoustical double wall for noise control Thermal double wall duct for temperature control ADMP s double wall round spiral pipe and fittings are typically manufactured with double wall flange. All sizes shall be defined by the inner shell/inside dimensions. Acoustical Double Wall Standard Acoustical double wall is for noise control. ADMP constructs this with a perforated inner shell surrounded by a solid outer shell. In between these two steel, shell walls is a layer of 1, 1-1/2 or 2 insulation per the engineer specifications or current SMACNA standards. The acoustical duct material has a K factor of.27 Btu/Hr/Sq.Ft./degree F. at 75 degrees Fahrenheit mean temperature. The perforated inner shell has 3/32 diameter holes staggered at 3/16 on center for a clear open area of 23%. Thermal Double Wall Standard Thermal double wall is for temperature control. ADMP constructs this with a solid inner shell surrounded by a solid outer shell. In between these two steel, shell walls is a layer of 1, 1-1/2 or 2 insulation per Solid Outer & Solid Inner Shell Diameter Material Thickness ASTM Type Length 4-64 Galvanized Ga. A-653 G60 OR G , 10 Standard 4-64 Paint Grip Ga. A-653 A , 10 Standard 4-60 Aluminum B H , 10 Standard 4-60 Stainless Steel Ga. A OR , 10 Standard *PVS specification book available **Only even sizes will be produced greater than 12 ID (Inside Diameter) Perforated Inner Shell Diameter Material Thickness ASTM Type Length 4-60 Galvanized Ga. A-653 G60 OR G , 10 Standard The sound rating of LMK-2775 will be equal to United K-27 duct and fittings since the gauges, hole diameter and percentage free area pattern and acoustical liner are identical. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), a wide variety of different radii are available. Flange connections are available by the following, but not limited to: Angle Rings or, AccuDuct, Spiral Mate. Fittings can have couplings built into their construction. Liners of fittings can be built with an extended coupling to aid field assembly. All fittings can have stop-beads incorporated, unless otherwise specified. Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. 2.1 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

13 Specialty Systems Dust Collection Systems Manufactured from the same high quality spiral lock pipe, our dust collection systems have a spiral lock seam and smooth interior for superior air flow. Using heavier gauges than standard galvanized pipe for air conditioning applications, dust collection systems include the same lapping seam construction, as well as a rounded entrance edge for conical tees, straight tees and laterals. With fittings machine-cut from our State-of-the-Art Vulcan Plasma table, every fitting falls within exacting tolerances. We also stock clean out caps, in-line clean outs, floor sweeps and blast gates. Exhaust Systems Manufactured from the same high quality spiral lock pipe, our exhaust systems have a spiral lock seam and smooth interior for superior air flow. Gauges for the spiral pipe and fittings are as dictated for the negative pressure requirements and current SMACNA standards, unless otherwise noted. ADMP s fittings include a lapping seam construction as well as a rounded entrance edge for conical tees, straight tees & laterals. 3.0

14 Low and Medium Pressure Acoustically Lined Spiral Duct and Fittings - CLM-0789 CLM-0789 duct combines galvanized ductwork with a 1 thick preformed fiberglass duct liner. Spiral pipe gauges will meet or exceed current SMACNA HVAC Duct Construction Standards, unless otherwise specified. A wide variety of fittings are produced by ADMP for Low and Medium Pressure acoustically lined systems including 90, 60, 45, and 30 degree elbows as standards, tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. For elbows, a centerline radius of one times the diameter is standard. 1-1/2 times the diameter to centerline (full radius) is standard. Gores & Seams: Lapping of seams are in the direction of air flow. The gore & seams are spot welded sand internally sealed using high pressure duct sealant. Fittings shall be spot welded and internally sealed with duct sealant. Gores Elbow Fitting Gauge 5 piece LV 3-10 ID 26 3 piece ID 24 2 piece 0-36 MV 3-20 ID 22 Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a special rounded entrance edge. They are not butt welded square entrance contractor type fittings. All fittings are lined with 1 thick preformed fiberglass duct liner. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), a wide variety of different radii are available. Flange connections are available by the following, but not limited to: Angle Rings or, AccuDuct, Spiral Mate. Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. 3.1 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

15 Exposed Spiral Pipe - Paintlock, Paint Grip, Mill- Phosphatized ADMP s spiral pipe, the ultimate in pressure-tight circular tubes of superior quality, is fabricated in exact sizes using paintlock steel with.03 inch galvanized coating on each side, ASTM A-591. The pipe consists of a smooth interior for low friction loss and 4 ply spiral lockseam entirely on the outside for high strength and rigidity. ADMP s spiral pipe is produced on a modern Betech pipe machine of proven performance. Thousands of feet, of this pipe, has been produced for such diverse installations as libraries, hospitals, multi-purpose and gymnasium school buildings & upscale restaurants. Couplings conform to SMACNA 2005 and ASHRAE standards for spiral pipe, unless otherwise noted. Seam metal is held to plus or minus.006 of an inch. Sizes and Gauges: 4-10 are available in 1 inch increments are available in 2 inch increments ADMP s spiral pipe construction will meet or exceed SMACNA 2005, 3rd edition unless otherwise specified. Hydrostatic Pressures Hydrostatic pressures to seam failure - all pressure in lbs. per square inch. Diameter gauge gauge gauge ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

16 Exposed Low Pressure Fittings, Paintlock Round These superior round fittings are made from accurate fitting patterns. The material used is paintlock steel galvanized.03 inches thick on each side. ASTM A-591. Usage: These very strong seams are designed for low pressure air systems used above ground. Couplings are built into the ends of the fittings. Types of Fittings: All standard fitting sizes and shapes are available. 90, 60, 45 and 30 degree elbows are standard. Other angles are available on special order. Tees, laterals (45 degree branch), reducers, and couplings are standard. For elbows a centerline radius of one times the diameter is standard. 1-1/2 times the diameter (full radius) and 2 times the diameter (long radius) are available. We can also make other size radii and other fittings as specified. Sizes and Gauges: 4-10 are available in 1 inch increments are available in 2 inch increments Construction of fittings will conform to the latest specifications of SMACNA and ASHRAE low velocity or high velocity standards unless otherwise specified. Fittings are machine cut from a scientifically developed, well proven, original pattern, assuring manufacturing tolerance consistency. 3.3 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

17 High Pressure Fittings for Paintlock Round A wide variety of round fittings are produced for high pressure including 90, 60, 45 and 30 degree elbows as standards, tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. Fitting ends are made with two inch male sleeves. Standard fittings have built-in slip type beaded couplings. Seams: Lapping of seams are in the direction of airflow. The finest continuous weld seams are made with Metal Inert Gas Shielded Welds (MIG). Welded seams are sprayed with zinc-rich coating material as primer and for added corrosion protection. SMACNA STANDARDS Gores Elbow Fitting Gauge 5 piece degree piece degree piece 0-36 degree Elbows, 1-1/2 times the diameter to centerline (long radius) is standard. Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a rounded entrance edge. They are not butt-welded square-entrance contractor-type fittings. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), a wide variety of different radii, fitting-to-fitting type joints are available. Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

18 Spiral Pipe - Stainless Steel The ultimate in pressure-tight circular tubes of superior quality in exact sizes from stainless steel type 304, 316, or 316L alloy, with smooth interior for low friction loss and a 4 ply spiral lockseam entirely on the outside for high strength and rigidity. Usage: Commonly produced for critical installations including caustic fume exhaust, automobile exhaust, and welding exhaust. Couplings conform with all specifications of the Sheet Metal and Air Conditioning Contractor National Association (SMACNA) recommendation for spiral pipe for both low and high pressure. Seam metal is held to plus or minus.006 of an inch. Sizes and Gauges: 4-10 are available in 1 inch increments are available in 2 inch increments ADMP s construction of spiral pipe for high pressure or low pressure - is manufactured to SMACNA rd edition standards, unless otherwise specified. Hydrostatic Pressures Hydrostatic pressures to seam failure - all pressures in lbs. per square inch. Diameter gauge gauge gauge ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

19 Stainless Steel High Pressure Fittings for Spiral Pipe A wide variety of round fittings are produced for high pressure including 90, 60, 45 and 30 degree elbows as standards, tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. Fitting ends are made with two inch male sleeves. Standard fittings have built-in slip type beaded couplings. Fittings: Lapping of seams are in the direction of air flow. The finest continuous weld seams are made with Metal Inert Gas Shielded Welds (MIG). SMACNA STANDARDS - Maximum 10 S.P.: Gores Elbow Fitting Gauge 5 piece degree piece degree piece 0-36 degree 22 For elbows, a wide variety of different radii are available; one and one-half diameter to centerline is standard. Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a special rounded entrance edge. They are not butt welded square entrance contractor type fittings. Fittings are machine cut on a scientifically developed, well proven, original pattern, assuring manufacturing tolerance consistency. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), a wide variety of different radii are available. Flange connections are available by the following, but not limited to: Angle Rings or, AccuDuct, Spiral Mate. Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

20 Aluminum Spiral Ductwork Aluminum spiral ductwork produced on our State-of-the-Art Betech pipe machine, is the ultimate in pressuretight circular tubes of superior quality. It consists of a smooth interior for low friction loss and a 4 ply lockseam entirely on the outside for high strength and rigidity. Sizes and Gauges: 4-10 are available in 1 inch increments are available in 2 inch increments SMACNA rd edition gauges will be used unless otherwise specified. Radius: Elbows will have a radius which is 1-1/2 times the diameter (long radius) to centerline is standard. Fitting ends are made with two inch male sleeves with a stop-bead up to 36 in diameter. Fittings will be welded. Fittings are machine cut on our State-of-the-Art Vulcan Plasma table, assuring manufacturing tolerance consistency. Specialty Fittings: Specialty configurations are available upon request. Some examples are as follows: Elbows (75, 15 and other degree angles are also available), a wide variety of different radii are available. Flange connections are available by the following, but not limited to: Angle Rings or, AccuDuct, Spiral Mate. Construction Standards: As listed in the current SMACNA HVAC Duct Construction Standards. Other regulatory construction standards are available upon request. 3.7 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

21 Dust Collection Systems Our spiral pipe, the ultimate in pressure-tight circular tubes of superior quality, is fabricated in exact sizes using galvanized steel. The pipe consists of a smooth interior for low friction loss and a 4-ply spiral lockseam entirely on the outside for high strength and rigidity. Dust collection system duct is manufactured with heavier gauges than normal air conditioning duct work. Fittings are two gauges heavier than the spiral duct. A wide variety of round fittings are produced by ADMP for High Pressure, including 90, 60, 45 and 30 degree elbows as standards (75, 15 and other degree angles are also available), tees, laterals, reducing laterals, reducers, couplings, end caps, crosses, etc. We also stock clean-out caps, in-line clean outs, floor sweeps, and blast gates. Standard fitting ends butt up against the spiral pipe and female couplings are used so that fitting or pipe ends do not protrude into the air stream. Fittings: Lapping of seams are in the direction of air flow. The finest continuous weld seams are made with Metal Inert Gas Shielded Welds (MIG). Welded seams are sprayed with aluminum paint containing rust inhibitor for added corrosion protection. Gores Elbow Fittings Gauge Pipe 5 piece degree piece piece and 90 degree elbows 4 through 10 diameter are smooth die-stamped type. For elbows, a wide variety of different radii are available; one and one-half diameter to centerline is standard. Entrance Edges: Particular attention is given to the entrance for conical tees, straight tees, and laterals. These fittings have a rounded entrance edge. They are not butt welded square entrance contractor type fittings. Fittings are machine cut on our State-of-the-Art Vulcan Plasma cutting table, assuring manufacturing tolerance consistency. Our spiral pipe is produced on our State-of-the-Art Betech Pipe machine of proven performance. Here at ADMP our experienced and knowledgable staff members are willing & able to assist you with your dust collection systems. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

22 (THIS PAGE INTENTIONALLY LEFT BLANK)

23 Square Duct Square Duct In today s competitive market, contractors are always looking for efficient ways to reduce overhead costs, particularly in the areas of expensive shop equipment. ADMP has the solution to this problem. We have the expertise and equipment to fabricate rectangular duct affordably and of the highest quality standards. Our machinery enables us to fabricate and assemble thousands of pounds of rectangular duct within days of the order. We guarantee delivery and service on all jobs regardless of size. Ductwork and fittings can be lined or unlined in 4 or 5 foot sections with connections such as S & D, Pittsburgh Seam and TDF. Accessories, such as gaskets, nuts and bolts, will be supplied for all duct work at the contractor s request. 4.0

24 Standard Saddle Tap Radius Elbow 45 Take Off Duct Square Elbow Take Off End Cap Flex Connection Square Box Sleeve Square Tee Sleeve Pants Radius Tee Square to Oval Radius 45 Take Off Saddle Tap Offset Transitions 2W Goose Neck Square to Round Roof Flashing Radius Offset Register Box Square Cross Radius 45 Saddle Lateral Tap 45 Square Elbow 45 Take Off Transition Tap In 4.1 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

25 Rectangle Duct Duct Dimensions Ga. Joint 0-16 (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type Flat S and Drive 1 Water gauge Transverse Joint Reinforcement Not required Intermediate Reinforcement S & Drive (TDC if 1 x 22 Ga. drive side above 20 ) Standing S Not required T-25a (See the current Not required SMACNA HVAC Duct Construction Mid-panel Conduit Standards Metal and (2) Mid-panel Conduits Flexible Manual for Conduit x 3/16 Angle details) and Mid-panel Conduit Alternative Flange Connections are available. Ask your ADMP Representative. Water Gauge Flat S and Drive 2 Water gauge Not required S & Drive (TDC if 1 x 24 Ga. drive side above 20 ) Standing S Not required T-25a (See the current Not required SMACNA HVAC Duct Construction Mid-panel Conduit Standards Metal and (2) Mid-panel Conduits Flexible Manual for Conduit x 2 Angle details) and Mid-panel Conduit Alternative Flange Connections are available. Ask your ADMP Representative. 2 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

26 Rectangle Duct Duct Dimensions Ga. Joint (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type Flat S and Drive 3 Water gauge Transverse Joint Reinforcement Not required Intermediate Reinforcement Water Gauge S & Drive (TDC if drive side above 20 ) T-25a (See the current SMACNA HVAC Duct Construction 1 x 24 Ga. Standing S Not required Not required Mid-panel Conduit 20 Standards Metal and Flexible Manual for Conduit (2) Mid-panel Conduits 18 details) 2-1/2 x 1/4 Angle and Mid-panel Conduit Alternative Flange Connections are available. Ask your ADMP Representative. 3 4 Water gauge T-25a Not required (See the current Not required SMACNA HVAC 22 5 Duct Construction Mid-panel Conduit Standards Metal and Flexible Manual for Conduit (2) Mid-panel Conduits details) /2 x 1/4 Angle Alternative Flange Connections are available. Ask your ADMP Representative ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

27 Rectangle Duct Duct Dimensions Ga. Joint (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type 6 Water gauge Transverse Joint Reinforcement Intermediate Reinforcement 9-12 T-25a Not required 24 (See the current Not required SMACNA HVAC Duct Construction Standards Metal and Mid-panel Conduit Flexible Manual for details) Conduit 18 (2) Mid-panel Conduits Not required Alternative Flange Connections are available. Ask your ADMP Representative. Water Gauge 6 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

28 Rectangular Reinforcements AMDP uses two types of duct reinforcement, internal tie rods & external angle reinforcements, located at duct joints and mid-panel on duct and fittings per SMACNA standards. We use tie rods when warranted unless otherwise requested. Angle Reinforcements Reinforcements must be fastened (tack welded, spot welded, riveted, screwed, or bolted) at 8 intervals maximum. When ends are tied, the 3/4 interval may be omitted. When reinforcements occur at the same location on adjacent sides at 4 W.G. (1000 Pa.) static and greater, tie the ends. 4.5 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

29 Rectangular Straight Duct 56 - finished length with TDF ends 59 - finished length with Slip & Drive ends 60 - length with raw ends AMDP produces rectangular ductwork to SMACNA 2005 Revision 3 standards based on information provided by the customer. We use SMACNA tables to determine requirements for metal gauge, end connections, reinforcements, and other features on all of our orders. We take pride in ensuring the customer receives the proper materials for the job. Straight duct can be shipped assembled or knocked down for tighter packing. Standard duct is manufactured as one piece wrapper, 2 piece L-shaped, or 4 separate sides. Beading is standard, unless designated by the customer. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

30 Rectangular Vanes Double Wall Vanes Single Wall Vanes Vanes are available for 90 degree ductwork turns to assist air flow. They are determined by SMACNA standards unless requested by the customer. Double vanes are standard with 2 vanes used up to 36 and 4 vanes at 36 and above. 4.7 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

31 Rectangular Longitudinal Seams Medium & Low Pressure Used for Medium Pressure duct Used for Low Pressure duct Notes: 1.) Ref: SMACNA-HVAC Duct Construction Standards-Metal & Flexible, Second Edition 1995, page 1-67, figure 1-5. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

32 Rectangular Transverse Connectors For Low Pressure Duct Notes: 1.) Ref: SMACNA-HVAC Duct Construction Standards-Metal & Flexible, Second Edition 1995, page 1-61, figure ) See Duct Construction Tables for limits of application. 4.9 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

33 Rectangular Transverse Connectors For Low Pressure Duct Corner Assembly The clamping TDC clips are installed with 6 wide, full coverage TDC clip tool as shown. For recommended clip spacing see chart 60 Duct (4) req d When using TDC in conjunction with slip-on four bolt connectors, it may be desirable to increase tension on TDC clip. To tighten the grip of the TDC clip to the flange by overbending the long leg of the clip, use the forming end of the tool as shown at left. CAUTION: Use of a hammer for installation will damage clip and may cause leakage. 48 Duct (3) req d 36 Duct (3) req d 24 Duct (2) req d 18 Duct & smaller (1) req d Recommended Clip Space 4.10 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

34 (THIS PAGE INTENTIONALLY LEFT BLANK)

35 Double Wall Rectangle Duct Duct Dimensions Ga. Joint 0-16 (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type Flat S and Drive 1 Water gauge Transverse Joint Reinforcement Not required Intermediate Reinforcement S & Drive (TDC if 1 x 22 Ga. drive side above 20 ) Standing S Not required Not required TDC Mid-panel Conduit (2) Mid-panel Conduits Conduit x 3/16 Angle and Mid-panel Conduit *The inner-wall/metal liner can be Solid or Perforated Metal. Alternative Flange Connections are available. Ask your ADMP Representative. Water Gauge Flat S and Drive 2 Water gauge Not required S & Drive (TDC if 1 x 24 Ga. Not required drive side above 20 ) Standing S Not required Mid-panel Conduit TDC Conduit (2) Mid-panel Conduits x 2 Angle 18 and Mid-panel Conduit 2 *The inner-wall/metal liner can be Solid or Perforated Metal. Alternative Flange Connections are available. Ask your ADMP Representative. ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

36 Double Wall Rectangle Duct Duct Dimensions Ga. Joint (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type Flat S and Drive S & Drive (TDC if drive side above 20 ) 5 TDC 3 Water gauge 4 Water gauge Transverse Joint Reinforcement Not required 1 x 24 Ga. Standing S 1 x 24 Ga. Standing S Not required Conduit Intermediate Reinforcement Not required Not required TDC Mid-panel Conduit Conduit (2) Mid-panel Conduits /2 x 1/4 Angle and Mid-panel Conduit *The inner-wall/metal liner can be Solid or Perforated Metal. Alternative Flange Connections are available. Ask your ADMP Representative. Not required Mid-panel Conduit (2) Mid-panel Conduits 2-1/2 x 1/4 Angle and Mid-panel Tie Rids *The inner-wall/metal liner can be Solid or Perforated Metal. Alternative Flange Connections are available. Ask your ADMP Representative. Water Gauge ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

37 Double Wall Rectangle Duct Duct Dimensions Ga. Joint (For Galvanized, 304 S.S. and 316 S.S. Ductwork) (Not for Aluminum) Transverse Joint Type 6 Water gauge Transverse Joint Reinforcement Intermediate Reinforcement Not required Not required TDC Mid-panel Conduit Conduit (2) Mid-panel Conduits Not required *The inner-wall/metal liner can be Solid or Perforated Metal. Alternative Flange Connections are available. Ask your ADMP Representative. Water Gauge 6 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

38 (THIS PAGE INTENTIONALLY LEFT BLANK)

39 #100 SNAP LOCK PIPE # ADJUSTABLE ELBOW SIZE GAUGE 4 x 5 30GA 5 x 5 30GA 6 x 5 30GA 7 x 5 30GA 8 x 5 30GA 9 x 5 30GA 10 x 5 30GA 12 x 5 30GA 14 x 3 28GA 14 x 5 28GA 16 x 3 28GA 18 x 3 28GA 20 x 3 28GA SMACNA GAUGES AVAILABLE SIZE QTY PER CASE GAUGE GA GA GA GA GA GA GA GA GA GA GA GA SMACNA GAUGES AVAILABLE SNAP LOCK PIPE & ELBOWS ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

40 REGISTER & STACK BOOTS #201 - STACK BOOT #202 REGISTER BOOT SIZE GAUGE 8 x 3¼ x 5 28GA 8 x 4 x 5 28GA 10 x 2¼ x (5,6,7) 28GA 10 x 3¼ x (5,6,7) 28GA 10 x 6 x 6 28GA 12 x 2¼ x (5,6,7) 28GA 12 x 3¼ x (5,6,7) 28GA 12 x 4 x (6,7) 28GA 12 x 6 x 7 28GA 14 x 2¼ x (6,7,8) 28GA 14 x 3¼ x (6,7,8) 28GA 14 x 4 x (6,7,8) 28GA 14 x 6 x 8 28GA 14 x 8 x 9 28GA 16 x 3¼ x 9 28GA 16 x 6 x 9 28GA REGISTER & STACK BOOTS SOLD LOOSE 6.1 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

41 #302 - REGISTER BOX - WITH HOLE (R6 1½ DUCT LINER) #303 - REGISTER BOX W/ DAMPER (R6 1½ DUCT LINER) #331 - INSULATED BOX - NO HOLE (R6 1½ DUCT LINER) SIZE QTY PER GAUGE CASE 6 x 6 x GA 8 x 4 x GA 8 x 4 x GA 10 x 6 x GA 10 x 6 x GA 10 x 8 x (6,7,8) 24 30GA 10 x 10 x (8,9) 18 30GA 12 x 6 x GA 12 x 6 x (7,8) 20 30GA 12 x 8 x (8,9) 16 30GA 12 x 12 x (8,9,10) 14 30GA 14 x 6 x (7,8) 16 30GA 14 x 8 x (8,9) 18 30GA 14 x 14 x (9,10) 12 30GA 16 x 6 x (8,9) 16 30GA ALSO AVAILABLE IN 6 TALL & SLANT SIZE QTY PER CASE GAUGE 6 x GA 8 x GA 8 x 6 (6,7) GA 8 x GA 10 x GA 10 x GA 10 x GA 12 x GA 12 x GA 12 x GA 14 x GA 14 x GA 14 x GA 16 x GA ALSO AVAILABLE WITH SIDE OR END OUTLETS (ALSO AVAILABLE WITH R4 OR R8 INSULATION) ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832) REGISTER BOXES 6.2

42 WYES & TEES #350 - WYE #360 - TEE (TEES ARE SOLD LOOSE) SIZE QTY PER CASE GAUGE 5 x 4 x GA 6 x 4 x GA 6 x 5 x GA 7 x 5 x GA 7 x 6 x GA 7 x 6 x GA 8 x 6 x GA 8 x 6 x GA 8 x 6 x GA 9 x 7 x GA 9 x 7 x GA 9 x 7 x GA 9 x 8 x (6,7) 12 28GA 10 x 8 x GA 10 x 8 x GA 10 x 8 x GA 10 x 8 x GA 10 x 8 x GA 10 x 9 x GA 12 x 9 x GA 12 x 9 x GA 12 x 10 x GA 12 x 10 x GA 12 x 10 x GA 12 x 10 x GA 14 x 10 x GA 14 x 12 x GA 14 x 12 x GA 16 x 14 x GA SPECIAL SIZES ARE SOLD LOOSE 6.3 ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

43 #440 - DUCT BOARD STARTING COLLAR #441 - DUCT BOARD STARTING COLLAR W/ DAMPER SIZE QTY GAUGE GA GA GA GA GA GA GA GA GA GA GA GA #460 - FLEX COUPLER (SOLD LOOSE) COLLARS & COUPLERS #480 - SNAP IN DUCT BOARD STARTING COLLAR (20) PER CASE #490 - SPIN IN COLLAR ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

44 REDUCERS & ROOF JACKS #500 - REDUCER (ALL #500 REDUCERS SHIPPED LOOSE) #570 - ROOF JACK (ALL #570 ROOF JACKS SHIPPED LOOSE) #580 - ROOF JACK WITH CAP SIZE GAUGE 4 x 3 28GA 5 x 4 28GA 6 x (4,5) 28GA 7 x (4,5,6) 28GA 8 x (4,5,6,7) 28GA 9 x (6,7,8) 28GA 10 x (7,8,9) 28GA 12 x (8,9,10) 28GA 14 x (9,10,12) 28GA 16 x (10,12,14) 28GA 18 x 16 28GA SIZE QTY PER CASE GAUGE GA GA GA GA GA STANDARD PITCHES ARE 0/12, 5/12, 6/12, 9/ ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

45 C&S DRIVE & CLEATS PLENUM HEATER STAND DAMPER WITH QUADRANT TRANSITION PLENUMS, TRANSITIONS, STANDS, DRIVE, CLEATS & DAMPERS (ALL ITEMS ON THIS PAGE ARE SHIPPED LOOSE) ADMP 6401 Long Point Rd. Suite 506 P. (832) F. (832)

46 (THIS PAGE INTENTIONALLY LEFT BLANK)