Preparation INSTALLATION INFORMATION
|
|
- Reynard Lucas
- 5 years ago
- Views:
Transcription
1 Preparaton 1 Pergo lamnate floorng materals are delvered wth nstructons n the form of llustratons. The texts below provde explanatons for the llustratons, and are dvded n three areas: Preparaton, Installaton and Cleanng nstructons. We recommend that you read through ths nformaton carefully whle studyng each llustraton. In case of doubts or questons please contact your dealer or techncal servces. The use of the orgnal Pergo accessores s strongly recommended to beneft from the full Pergo warranty. 1 = 2 Pergo lamnate floors can be bought n dfferent formats, decors and qualtes. Make sure you have receved the floorng that you ordered before startng the nstallaton. It s always a good dea to store one end label together wth your recept. 2 3 After recevng the floor packs these should be acclmatzed, unopened and stored n a flat poston free from the wall and floorng pror to nstallaton. We recommend storng them at normal room temperature (between degrees C / degrees F) and a relatve humdty (RH) between 30 75% for a mnmum of 48 hours pror to nstallaton mm 500 mm 48h >15 C 30-75% RH 4 Pergo lamnate floorng must be nstalled on a sold, selfsupportng subfloor, wood floorng or floors covered wth seamless, undamaged vnyl. In case of textle floor coverngs, however, both the textle floorng and the eventual underlayment must be removed. 4
2 Preparaton 5 The entre subfloor must be carefully checked for any unevenness. Usng a 1 m straght edge, make sure there are no unevenness of more than 2mm. Also make sure there are no peaks hgher than 1.2mm wthn a 250mm radus. In case of sand or grnd peaks, use self-levelng compound as needed to acheve correct flatness. Let ths cure and dry before nstallaton. Ask your dealer for advce mm < 2 mm 250 mm < 1,2 mm 6 After checkng the subfloor for unevenness, carefully vacuum the entre surface. To avod rsk of squeakng, secure any loose partcleboard, OSB, fberboard, tmber planks etc. wth screws. 6 7 To acheve optmal sound protecton, best possble walkng comfort, to avod squeakng n jonts and to level out mnor unevenness n the subfloor an approprate Pergo underlayment s strongly recommended. Ask your dealer for advce. If other than Pergo underlays are used or f the chosen Pergo underlay does not have a vapour barrer, a 0,2mm PE-flm has to be nstalled as a mnmum damp protecton f such s needed (see ll.10). The PE-flm must be overlappng n the seams at least 200mm. 7 Recommended PERGO underlayments. 8 Pergo lamnate floorng must not be nstalled n a typcal wet room or n rooms wth a floor dran. 8
3 9 Preparaton Pergo lamnate floorng s desgned to be nstalled as a floatng floor to allow natural expanson and contracton wth changes n temperature and humdty. To acheve the benefts of a floatng floor and to avod possble gaps, squeakng etc. never fasten the floor wth nal, screws, slcone etc. Pergo lamnate floorng must not be nstalled drectly on floor josts Mneral subfloors such as concrete must be suffcently dry pror to nstallaton. (<2,5% CM / 75% Tramex). If the mosture content s hgher, or may become hgher, other types of damp proofng lke Pergo MosturBloc must be used. Ask your dealer for advce. A vapour barrer must be used when nstallng Pergo on mneral subfloors regardless the age of the subfloor. Pergo Smart Underlay+ and Pergo Professonal SoundBloc have an approprate vapour barrer bult-n. 10 <2,5 CM% / Tramex RH 75% PERGO comb underlay/ 0,20 mm PE fol + Pergo underlayment 11 When nstallng Pergo lamnate on under floor heatng a vapour barrer always must be put down before recommended underlay s nstalled. We recommend usng one of the Pergo underlays whch have a vapour barrer ncluded. Your dealer or nstaller of the underfloor heatng system must guarantee that the surface temperature never exceed 28 degrees C. 11 Max 28 C PERGO comb underlay/ 0,20 mm PE fol + Pergo underlayment
4 Preparaton 12 A Pergo lamnate floor s manly composed of natural wood and wll naturally expand and contract upon changes n the relatve humdty. The dmensonal varaton of the nstalled floor wll almost be equal n length and wdth. At 20 C and a relatve humdty, RH, between 40-60%, the movement s mnmal. Pergo lamnate floorng s produced and delvered wth a mosture content to cope wth a RH between 30-60%. In dry clmate, for example n the Nordcs durng wnter tme, the RH mght drop below 30% and n summertme rse above 70%. Ths wll create movements n the floor surface. To secure enough clearance for the natural movements and to avod possble open jonts, squeakng etc. always keep a dlataton jont of 5mm average to walls, thresholds, starcases, ppes etc. durng nstallaton. Use the spacers of the nstallaton kt to keep the rght clearance. Installng n wnter tme n very low RH, the clearance to the wall should be lowered to 3mm snce the floor panels wll shrnk, and f nstallng n hgh RH clmate the clearance should be rased to 8mm snce the floor panels wll expand. The clearance must be left open and may NOT be flled by any sealant, slcone or other adhesve. Never fasten the floor wth nals, glue, screws or n any other way % RH % 50% 75% X X x = 3 mm x = 5 mm x = 8 mm 13 Due to the fact that all types of wood materal by nature wll shrnk and expand and cope to the changes n relatve humdty and temperature we keep as a general rule not to nstall Pergo lamnate n room sze more than 13x13 meter. If the surface to cover s bgger, ask the dealer or Pergo techncal servce about optons. It s mandatory to nstall T-moldngs n any doorway. In typcal T L or U shaped rooms t may also be necessary to nstall a dlataton jont. Ask for advce n case of doubt. 13 < 13 m < 13 m
5 14 Preparaton A Pergo 5-n-1 moldng s a perfect soluton n stuatons lke llustrated. Ths moldng can also take care of transton as well as fnshng edges aganst vertcal surfaces such as thresholds, sldng door frames etc. (End moldng). When usng the 5-n-1 moldng, always remember to keep the rght dlataton gap between the nstalled floor and the metal track. 14 < 13 m < 13 m X X X
6 Installaton 15 Pergo lamnate floors are easy to nstall and requre no expensve specalty tools. In addton to a few common DIY tools (foldng rule, pencl, hammer, handsaw or jgsaw, carpenters square and possble power drll and workng gloves), you only need a Pergo Installaton Kt contanng a tappng block, pull bar and spacers. Be sure you have all tools avalable before startng the nstallaton. 15 3mm 5mm 1mm 2mm 5mm 3mm 5mm 2mm 1mm 2mm 5mm 2mm 16 When cuttng the Pergo plank, be sure you are not creatng splnters or chppng when cuttng. If usng a hand saw, keep the decoratve surface faced up, and f usng a jgsaw keep the decoratve surface down Every Pergo plank s methodcally checked for any mperfectons before beng packed. Stll, packs or planks can be damaged durng transportaton or when the packs are opened. Do not nstall a plank wth a damaged surface, edge or clck jont. Carefully nspect each plank before and durng the nstallaton n good lght condtons. An nstalled plank s consdered as accepted, and can not be clamed. 17
7 18 Installaton Before startng, carefully measure the length and the wdth of the room to plan a precse layout to acheve a balanced appearance of the floor. Ths s very mportant when nstallng typcal tle decors. Ths wll ensure also you won t end up wth the last row beng too narrow. If the last row would be less than 40mm, the nstallaton wll be easer f you cut down the planks of the frst row n the length. 18 >40mm 19 Often the nstallaton s done parallel to the long walls of the room. The most common drecton of nstallaton for all type of lamnate floors s from left to rght, and ths nformaton s referrng to an nstallaton from left to rght. The planks should be nstalled facng the tongue sde (A) to the wall. Always remember the spacers! Thanks to the PerfectFold TM 3.0 patent, the nstallaton s very easy. Ths patent s off great use when dsmantlng a plank f needed wthout destroyng the connecton mechansm. The end jont can be assembled n dfferent ways by foldng down, anglng, sldng or tappng n horzontally. The quckest, easest and most secure way s by foldng down. 19
8 Installaton 20 Narrow down the wdth of the planks of the frst row (ref. ll 18) or as a mnmum cut off the tongue (ref ll. 19) to acheve the rght dstance to the wall. If the wall s curved/uneven, the frst row has to be cut and coped to the contour off the wall. Use spacers! Cut off the tongue on the frst plank also on the short sde. Ths plank wll then have the plastc nsert n the end to the rght, on the groove sde. 20 For Pergo Modern Plank Sensaton, the plastc nsert s on the tongue sde. The nstallaton procedure for both clck-systems s exactly the same. 21 The easest way to connect the planks s by a rotatng fold down movement. Lft the connectng plank up n an angle of degrees, push t nto the long sde groove and slde t gently to the left untl the plank ends meets. Push the plank frmly downwards to the floor, and the PerfectFold TM 3.0 patent wll lock the jont perfectly n the end. Always control each jont before contnung. Use the Pergo tappng block gently to tghten up small gaps f needed Install the frst 2 rows n accordance to the llustraton. We recommend the overlap/staggerng between end jonts to be about 1/3 of the plank length, but never less than 300mm. Installng the 2 frst rows lke shown wll help to keep a straght edge to start the rest of the nstallaton. The cut off from the frst and second row should normally be perfect as startng planks n the thrd and fourth row. Always remember usng the spacers to keep the rght dstance to walls etc. 22 1/3-1/2 (> 300 mm)
9 Installaton 23 For a nce fnsh where the new floorng meets a threshold, we recommend undercuttng the moldngs of the door. To secure the rght cut off, turn a Pergo plank upsde down and place t on the floor up to the door frame. Then, place the hand saw flat aganst the plank and smply cut through the frame/moldng as shown. Remove the cut out and vacuum away derbes. You can then smply slde the floor underneath the frame/moldng when nstallng and make a perfect fnsh For the fnal row, cut the planks n the length rememberng to leave the recommended expanson space and makng necessary adjustments to follow the contour of the wall. If there s a door way n ths wall, clck the plank n on the long sde at the sde of the undercutted moldng, slde/tap the plank underneath and thanks to the PerfectFold TM 3.0 you are able to lock the end jont by just tappng the end jont together wthout needng to lft the plank. Control the tghtness n the jont, and use the pull bar to secure absolute tghtness. 24
10 25 Installaton To nstall Pergo domestc Elegance floorng around ppes, carefully measure and mark the planks wth the exact centre pont for each ppe. Drll a hole at each of the marked ponts that s equvalent to the dameter of the ppe + 16mm. If located on the long sde of the plank, make a 45 degree cut from each hole to the edge of the plank, and then cut between the holes as shown. If located on the end of a plank, make a straght cut across the plank. Install the plank. Then, usng Pergo SafeSeal or regular wood glue along the cut edges of the pece you cut out, glue the pece n place where t belongs. Be sure no glue comes between the cut out pece and the subfloor. Use spacers to secure a tght glue jont, and remove any glue or SafeSeal on the floor surface drectly wth a damp cloth. The gap you have created between the ppes are to ensure the floor can move as expected from season from season, and are NOT to be flled wth any sealant, slcone or other adhesve. Use Pergo radator caps to conceal gaps around radator ppes. 25 Ø D Ø D + 13 mm/ + 20 mm cf. 26 Inspect the fnal surface of the nstalled floor, remove all spacers and nstall Pergo wall bases accordng to the nstructons followng the wall bases. 26
11 Instructons for extra water protecton Modern Plank - Sensaton 27 Ths nstallaton nstructon can prevent water nfltraton around the permeter and obstacles of your lamnate floorng. The Modern Plank Sensaton lamnate tself s water resstant after nstallaton. Followng these nstructon carefully makes the floor ft for use n bathrooms, ktchens, laundry rooms and entrance areas. The Modern Plank-Sensaton panels are not sutable for use n damp spaces lke pool areas, saunas and rooms wth buld-n drans lke showers. These extra water protecton nstructons do not cope to natonal regulatons of water protecton n wet rooms. For a water resstant fnshng, use the elastc waterproof transparant paste (PG Aqua Sealant) and the foamstrp (NEFOAMSTRIP) Sealng the permeter expanson jonts combnes the compressble PE foamstrp (NEFOAMSTRIP) wth dameter 8 to 10 mm and the flexble and waterproof PG Aqua Sealant. Push the PE foam n the expanson jonts and apply the transparent PG Aqua Sealant under slght angle towards the Pergo - Sensaton floor. Install the wallbases wth PG Multglue (PGGLUE290). Apply the flexble PG Aqua Sealant between wallbases and floor to avod ngress of water. In places where profles or wallbases cannot be placed, nsert a PE foamstrp (NEFOAMSTRIP) n the expanson jonts and fnsh wth elastc paste (PG Sealant). Tp: To make work more cleaner t can be easy to put a tape on the floor before applyng the PG Aqua Sealant. Ths tape can be removed mmedatly after applyng the PG Aqua Sealant. Splled PG Aqua Sealant can be removed easly when t s dry. 28
12 29 Instructons for extra water protecton Modern Plank - Sensaton For a water resstant fnshng of the 5- n -1 mouldng profle (PGINCP), fx the 5- n -1 mouldng profle to the base floor wth the PG Multglue and/or screws. Apply transparent PG Aqua Sealant on the flexble PE foam that s n the expanson jont. Push the 5-n-1 mouldng profle n the base profle and the wet PG Aqua Sealant For a perfect water resstant fnshng around ppes, use PG Radator caps, the elastc waterproof transparant paste (PG Aqua Sealant) and the foamstrp (NEFOAMSTRIP). Put the foamstrp n the expanson jont around the ppe. Place the ppe cover and apply PG Aqua Sealant around the radator cap and around the tubes. Ths makes the ngress of water mpossble To secure extra water protecton around the permeter of the floor and avod water to enter underneath the panels, apply the flexble PG Aqua Sealant up to the wall base, thresholds, door frames, ppe covers etc. 31
13 Cleanng Instructons 32 After nstallaton, vacuum usng a vacuum head wth soft edges Dry mop or sweep the floor to remove drt and dust. Wpe the floor wth hand warm water contanng one or two bottle caps of Pergo all-round cleaner and usng Pergo mcro fber mop. The daly cleanng should follow the nstructons on the Pergo web ste. The use of napproprate cleanng products mght damage the floorng surface
14 34 Cleanng Instructons Castor chars must have castors made for hard surfaces, so called Soft wheels Softwheel 35 All furnture legs should be protected wth felt pads to avod scratchng the fnshed surface. Avod sldng heavy furnture etc. over the Pergo floor to avod possble scratchng. Lftng the furnture s recommended. Always place a qualty door mat at any entrance door to protect for sand and drt whch mght create scratches
premium click optimum click
1 In order to obtain a good result, we advise to follow all given instructions carefully. PREPARATION We recommend to order all panels for the same flooring project at the same time. 2 Always store and
More informationMANUAL INSTALLATION MAINTENANCE ARCHITECHURAL GUIDE
MANUAL INSTALLATION MAINTENANCE ARCHITECHURAL GUIDE CONTENTS Secton 1 - Product Overvew Secton 2 - Typcal Applcatons Secton 3 - Lmtatons Secton 4 - Tools and Equpment 4.1 Installaton Tools Lst 4.2 BoClad
More informationMANUAL INSTALLATION MAINTENANCE ARCHITECHURAL GUIDE
MANUAL INSTALLATION MAINTENANCE ARCHITECHURAL GUIDE CONTENTS Secton 1 - Product Overvew Secton 2 - Typcal Applcatons Secton 3 - Lmtatons Secton 4 - Tools and Equpment 4.1 Installaton Tools Lst 4.2 BoClad
More informationoptimum glue Preparation INSTALLATION INFORMATION We recommend to order all panels for the same commercial flooring project at the same time.
Preparation We recommend to order all panels for the same commercial flooring project at the same time. Always store and transport your vinyl floor carefully to prevent distortions. Store and transport
More informationFor more information, call PERGO
SYSTEM SYSTEM MADE IN THE USA SPECIALLY DEVELOPED FOR LAMINATE FLOORING FL OZ (33.ml) 0 ON 0 2 0 00 Non Destructive Moisture 3 0 Concrete Encounter Plus 200 20 dlfwej dtra djflsv dlfwe vtra alskdjf vmwjc
More informationINSTALLATION INSTRUCTIONS
CLICK BAMBOO FLOORING INSTALLATION INSTRUCTIONS General The locking system is a revolutionary system for installing bamboo floors without using glue. The panels can be clicked together simply. Position
More informationpremium click optimum click
5 golden rules Install your floor between 18 and 30 C. 48h Pergo Vinyl must be acclimatized in the room of installation between 18-30 (64-86 F) for a period of at least 48 hours before installation. This
More informationINDIVIDUAL SOLUTIONS FROM A SINGLE SOURCE
Extract of the general catalogue, CHAPTER F INDIVIDUAL SOLUTIONS FROM A SINGLE SOURCE Systems dversty for warehouses, factores and workshops GENERAL CATALOGUE Modular shelvng mezzannes and platforms optmal
More informationINSTALLATION INSTRUCTIONS LAMINATE
INSTALLATION INSTRUCTIONS LAMINATE DROP LOCK GENERAL INSTRUCTIONS FOR LAMINATE HARDWOOD FLOORING ACCLIMATION Acclimation is a recommended procedure prior to installation of laminate flooring either on
More informationLAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING
LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR DROP LOCK FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s satisfaction.
More informationInstallation Instructions for SuperFast Hurricane
SuperFast Hurricane Installation Instructions for SuperFast Hurricane I. Before You Start / Preparations Please read all the instructions before you begin the installation. Improper installation will void
More informationLAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING
LAMINATE GENERAL INSTALLATION INSTRUCTIONS FOR ANGLE-TO-ANGLE FLOORING WARNING Prior to installation, please ensure that the product received is the correct style and color as well as to the customer s
More informationSchluter -KERDI-BOARD Substrate, building panel, bonded waterproofing
Substrate, buldng panel, bonded waterproofng The unversal substrate for tles Flat. Level. Plumb. Square. Whether you work wth mosacs or largeformat tles, an absolutely flat substrate wth straght and precsely
More informationQuick Step Studio Laminate Flooring Installation Instructions
Quick Step Studio Laminate Flooring Installation Instructions Tools Required for Installation Job Site Site Requirements Laminate is a durable floor covering, not intended as structural material. Laminate
More informationFor more information, call PERGO
SILICONE SILICONE SYSTEM SYSTEM MADE IN THE USA SPECIALLY DEVELOPED FOR LAMINATE FLOORING FL OZ (.ml) 0 0 0 00 ON Non Destructive Moisture 0 Concrete Encounter Plus 00 0 dlfwej dtra djflsv dlfwe vtra alskdjf
More informationMega Clic Laminate Floor Installation Instructions
Mega Clic Laminate Floor Installation Instructions GENERAL Mega Clic is a revolutionary system for installing laminate floors without using glue. The planks can be clicked together simply, thanks to the
More informationAbsco Space Saver Shed Assembly Instructions Model: 23151SK
Assembly Instructons Model: 235SK FRONT BASE LENGTH: 2.26m SIDE BASE LENGTH:.52m FRONT WALL HEIGHT:.8m REAR WALL HEIGHT: 2.08m CONCRETE SLAB 620mm 2360mm WHEN LAYING YOUR CONCRETE SLAB, CHAMFER THE 50mm
More informationLaminate Flooring Charlestowne Collection
Laminate Flooring Charlestowne Collection Warranty This quality laminate flooring is under warranty for 25 years not to fade, wear through or stain. This warranty applies only to the original purchaser.
More informationWET SUBSTRATE UNEVEN FLOOR ACOUSTIC COMFORT TARKO SOLUTIONS PRESERVED FLOORING. Underlayers & overlayers DAMP PROOF FLOOR PROTECTION 06/2016
ING 06/2016 Type of floorng Traffc ING MINOR IRREGULARITIES MAJOR IRREGULARITIES TEMPORARY INSTALLATION ASBESTOS TILES Vnyl - HE rolls Vnyl - HO rolls Lght to moderate LAY (1) - Heavy LAY (1) - Lght to
More informationInstallation Manual. For the competent person. Installation Manual. Flue pipe for ecotec plus. Concentric Ø 110/160 GB, IE
Installaton Manual For the competent person Installaton Manual Flue ppe for ecotec plus Concentrc Ø 0/60 GB, IE Table of contents Table of contents Notes on the documentaton...3. Observng other applcable
More informationGardenpro Masterstore Series Shed Model: J30152MK
Shed Model: J305MK FRONT BASE LENGTH: 3.0m SIDE BASE LENGTH:.5m FRONT WALL HEIGHT:.80m REAR WALL HEIGHT:.08m 60mm SLAB WIDTH CONCRETE SLAB 300mm SLAB LENGTH We thank you for choosng an Australan Made Shed.
More informationLife. Home. In Harmony.
Life. Home. In Harmony. Harmonics Toasted Cinnamon Oak with SplashDefense Floor Installation Instructions Tools Required for Installation Common Tools Other Tools and Supplies Job Site Site Requirements
More information1. PREPARATION 2. INSTALLATION 3. FINISHING 4. MAINTENANCE
In the following text vinyl floor(s) refers to floors from the Quick-Step Livyn Ambient Glue+ and Balance Glue+ collections. The branded accessories refer to the specific Quick-Step vinyl accessories.
More informationAbsco Space Saver Shed Assembly Instructions Model: 15081SK
Assembly Instructons Model: 508SK FRONT BASE LENGTH:.52m SIDE BASE LENGTH: 0.78m FRONT WALL HEIGHT:.8m REAR WALL HEIGHT:.95m CONCRETE SLAB 620mm 880mm WHEN LAYING YOUR CONCRETE SLAB, ENSURE THERE IS A
More informationMohawk SolidTech. SolidTech Installation Guidelines. Preparation
55 85ºF (13 30ºC) Preparation We recommend placing a single order for all cartons required for a commercial flooring project. 1. Always store and transport SolidTech Luxury Vinyl Flooring on a flat surface
More informationINSTALLATION GUIDE. Please read all the instructions before you begin the installation. Improper installation will void warranty.
INSTALLATION GUIDE I. Before You Start / Preparations Please read all the instructions before you begin the installation. Improper installation will void warranty. Important notice All wood based products,
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION For EGGER FLOORING with glueless locking system PRO CLIC! PATENTED www.egger.com INSPECTION RESPONSIBILITY / SUB FLOORS 1. INSPECTION RESPONSIBILITY Laminate flooring from EGGER
More informationVerify colour and finish before installation. Once the floor is installed, it is deemed to have been inspected, approved and accepted.
CLICK LAMINATE FLOORING INSTALLATION GUIDELINES Before you start read these Installer/Owner Responsibilities: Relative Humidity (RH) requirements: Laminate floors require a Relative Humidity of 35% - 50%
More informationUse a special underlay above 45 C. Click-it! Never use a hammer or tapping block. Keep indoor climate conditions above 0 C.
GOLDEN RULES 8-0 C Install your fl oor between 8 and 0 C. Quick-Step Livyn must be acclimatized in the room of installation between 8-0 C (- 8 F) for a period of at least 8 hours before installation. This
More informationpremium click optimum click
5 golden rules 48h 18-30 Install your floor with a room- and floor temperature between 18 and 30. Pergo Vinyl must be acclimatized in the room of installation between 18-30 (64-86 F), preferably at normal
More informationRigid Core Installation & Maintenance Instructions
Rigid Core Installation & Maintenance Instructions Suitability Rigid Core Click Vinyl Flooring is completely waterproof floating floor and has got exceptional acoustic and insulation properties due to
More informationTARKETT EASIUM. Instrucciones de Instalación & Mantenimiento
TARKETT EASIUM Instrucciones de Instalación & Mantenimiento Product usage Recommended tools Easium flooring is not recommended for use in high humidity areas where the floor is usually wet (steam rooms,
More informationGeneral and Installation Instructions Laminate - 2G + 2G
STOP Please inspect product for color, finish, quality and style BEFORE installing any material. SLCC Enterprise, Inc. warranty DOES NOT cover materials with visible defects once they have been installed.
More informationInstallation instruction
TACKY TILE Installation instruction Introduction Tacky Tile has a Tacky technology backing that bonds firmly but not permanently to the subfloor, making installation easy, fast and clean. If at any time
More informationInstallation. Installation Instructions - Laminate Flooring with Drop lock. I. Before you start. Subfloors with radiant heat. Floating installation
Installation Instructions - Laminate Flooring with Drop lock I. Before you start Keep the boards at room temperature for at least 48 hours in unopened package before you start the installation. The room
More informationpremium rigid click optimum rigid click
In order to obtain a good result, we advise to follow all given instructions carefully. www.pergo.com Preparation We recommend to order all panels for a commercial flooring project at the same time to
More informationLuxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call
Luxury Vinyl Plank (LVP) Flooring Installation Guide For Assistance call 702-534-1115 IMPORTANT Save time & avoid frustration! Read these entire instructions before starting your installation! Prior to
More informationTuneable hydrogels. complete.handy.simple USER GUIDE. Innovative cell culture systems.
complete.handy.smple USER GUIDE Innovatve cell culture systems. Innovatve cell culture systems. MATERIAL NEEDED Materal ncluded Lyophlzed peptde gel powder n glass val Materal not ncluded Dstlled water
More informationUSA USA USA PURE CLICK
MADE IN BELGIUM MADE IN BELGIUM 0. MADE IN BELGIUM 100 % QUALITY USA USA USA 100 100 % % QUALITY QUALITY PURE CLICK CLICK CLICK DESIGN CLICK DESIGN FLOOR FLOOR INSTALLATION MANUAL 2 Pure Click 40 is a
More informationMethod for measuring viscoelastic properties of wood under high temperature and high pressure steam conditions
J Wood Sc (1999) 45:373-377 The Japan Wood Research Socety 1999 Wahyu Dwanto Toshro Morooka Msato Normoto Method for measurng vscoelastc propertes of wood under hgh temperature and hgh pressure steam condtons
More informationIN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY.
IN ORDER TO OBTAIN A GOOD RESULT, WE ADVISE TO FOLLOW ALL GIVEN INSTRUCTIONS CAREFULLY. 8-0 C < C > C Basic a b SunHeat. PREPARATION Always store and transport Quick-Step Livyn floors carefully to prevent
More informationIMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING
IMPORTANT NOTES ABOUT YOUR FLOORING PLEASE READ BEFORE INSTALLING ACCLIMATIZATION AND STORAGE Your new flooring has to be acclimatized for 24 hours before installation begins. The flooring must remain
More informationConcrete 1,8 2,0 Anidrite 0,3 0,5
GUIDE FOR FLOATING CORK FLOORS TRANSPORT, STORAGE AND ACCLIMATIZATION Transport and store cartons in a horizontal position. Tiles and adhesive must be acclimated on-site in its original packaging. Store
More informationINSTALLATION INSTRUCTIONS - Please read before installation
INSTALLATION INSTRUCTIONS - Please read before installation The floor panels should be transported in a lying down position. Floor panels should be stored in this position in their unopened packages in
More informationINSTALLATION INSTRUCTIONS
1 of 6 INSTALLATION INSTRUCTIONS IMPORTANT! Store the floorboards at room temperature for at least 48 hours, still in their packaging, prior to commencing installation. Ideal room temperature is 18-22
More informationLock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered
Lock Installation Instructions for BT Strand Lock, BT Strand Engineered & BT Bamboo Engineered Please read the following instructions before starting the installation Applications... 1 Pre installation...
More informationPARKAY XPR Installation Instructions (Architect Collection)
Parkay Floors 1-855-5-PARKAY www.parkayfloors.com PARKAY XPR Installation Instructions (Architect Collection) BEFORE YOU START PARKAY XPR FLOORING has a patented locking system making it ideal for a floating
More informationWellmade En VogueTM Engineered Vinyl Plank Installation Guide
Wellmade En VogueTM Engineered Vinyl Plank Installation Guide Wellmade En VogueTM is a one of a kind engineered vinyl plank flooring that uses no adhesive to bond the vinyl layers together and features
More informationInstallation instruction
Installation instruction BJELIN PARQUET PLANK Locking system G/G . Installation preparations 8 h ( h) - C -0% at 0 C - C. Subfloor preparations PE-foil over floor heating mm underlay material: CS > 0 /
More informationHYBRID. Pre-Laying Checks
Warning Veles CK has been developed for exceptional stability in low and high temperatures, however, after installation extreme temperatures (under 5 C or over 50 C) should be avoided by use of interior
More informationSchlüter -KERDI-BOARD. Waterproof substrate and structural board
Waterproof substrate and structural board A comprehensve substrate soluton for tle and stone. Perfect Coverng Lghtweght, practcal, and easy to nstall - n contrast to conventonal structural panels, whch
More informationINSTALLATION INSTRUCTIONS
About PROTECH Luxury Vinyl Planks 8.7mm WPC Click Lock Contemporary Collection features patented interlocking planks for easy installation and is installed as a glue less floating floor. The interlocking
More informationINSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION EGGER LAMINATE FLOORING with glueless locking system just clic! www.egger.com INSPECTION RESPONSIBILITY / SUB FLOORS 1. INSPECTION RESPONSIBILITY Laminate flooring from EGGER is
More informationRigid Core (White Label) Planks with Interlocking Joints (Glueless) Installation Instructions
Rigid Core (White Label) Planks with Interlocking Joints (Glueless) Installation Instructions Rigid Core Planks are constructed with a joint that locks the planks together to form a tight, durable, water
More informationLuxury Vinyl Planks with Interlocking Joints (Glueless) Installation Instructions
Luxury Vinyl Planks with Interlocking Joints (Glueless) Installation Instructions Luxury Vinyl Planks are constructed with a joint that locks the planks together to form a tight, durable, water resistant
More informationVESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE
VESDURA ENGINEERED VINYL PLANK INSTALLATION GUIDE Vesdura Engineered Vinyl Plank features the patented Unilin interlocking planks for easy installation and is installed as a glueless floating floor. The
More informationPARKAY LAMINATE FLOORING (UNILIN DROP) Installation Instructions
Parkay Floors 1855-5-PARKAY www.parkayfloors.com PARKAY LAMINATE FLOORING (UNILIN DROP) Installation Instructions BEFORE YOU START PARKAY LAMINATE FLOORING has a patented UNILIN DROP system. The collections
More informationsono BETTER TO THE CORE SONO INSTALLATION GUIDE GLUE-DOWN INSTALLATION 1. GENERAL INFORMATION 2. TOOLS AND MATERIALS 3.
SONO INSTALLATION GUIDE GLUE-DOWN INSTALLATION Congratulations and thank you for choosing SONO floors! Your new floors are among the most fashionable, long-lasting and easy-to-maintain floors available.
More informationALL DRAWINGS/ILLUSTRATIONS ARE LOCATED AT THE END OF THE INSTRUCTIONS.
Saxony Installation Instructions Planks are constructed with a joint that locks the planks together to form a tight, durable, water resistant joint. Saxony is installed as a floating floor so it's quick
More informationPremium Glueless Luxury Vinyl with Interlocking Joints Installation Instructions
Premium Glueless Luxury Vinyl with Interlocking Joints Installation Instructions Premium Glueless Luxury Vinyl planks are constructed with the patented Uniclic interlocking joint that locks the planks
More informationINSTRUCTIONS FOR INSTALLATION
INSTRUCTIONS FOR INSTALLATION Dear customer, Thank you for purchasing our Par-ky veneer wood floor. It is essential to read these instructions for installation attentively. If these instructions are not
More informationSTANDARDS LAMINATE FLOORING (UNILIN A2A) Installation Instructions
STANDARDS LAMINATE FLOORING (UNILIN A2A) Installation Instructions BEFORE YOU START 1. STANDARDS LAMINATE FLOORING has a patented UNILIN A2A locking system. The collections that carry this particular Click
More informationIVC US Residential Installation Guide - Laminate. Leading the Way
IVC US Residential Installation Guide - Laminate Leading the Way IVC US Residential Installation Guide - Laminate PressXpress & DropXpress IVC US Residential Installation Guide Laminate & DXP Materials
More informationScuba Seal Installation / Floor Care Instructions With Video Link
Scuba Seal Installation / Floor Care Instructions With Video Link 04/12/18 Congratulations on choosing ScubaSeal. ScubaSeal Rigid Core Flooring has the beautiful designs that are perfect for your active
More informationMEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL
REVISED 1/24/2017 MEDLEY XL INSTALLATION & MAINTENANCE INSTRUCTIONS LUXURY VINYL PLEASE READ ALL INSTRUCTIONS CAREFULLY, BEFORE YOU BEGIN INSTALLATION. IMPROPER INSTALLATION WILL VOID WARRANTY. Thank you
More informationWPC VINYL PLANK INSTALLATION GUIDE
WPC VINYL PLANK INSTALLATION GUIDE Please check color selection and style before Installation. NO CLAIMS will be accepted after installation if installation instructions are not followed. NO CLAIMS will
More informationATTENTION! READ BEFORE INSTALLING!
ATTENTION! READ BEFORE INSTALLING! FOR BEST VISUAL REPRESENTATION OF YOUR FLOOR This flooring replicates the look of a natural product which has natural variations in color and texture. For best visual
More informationHDWPC Flooring Installation Guidelines
HDWPC Flooring Installation Guidelines 02.22.17 The purpose of this manual is to provide general installations recommendations based on certain installation environments. If there are other questions about
More informationGeneral Commercial Installation Guide LAMINATE
General Commercial Installation Guide LMINTE Laminate & DXP IVC US Commercial Installation Guide - Laminate PressXpress & DropXpress Materials Required for Installation: Small hand saw Jigsaw Pencil ox
More informationPURE INSTALLATION MANUAL
INSTALLATION MANUAL Pure Click 40 is an LVT floor, designed for use in residential areas. Pure Click 55 is suited for both residential and commercial areas such as shops, hotel rooms, etc. To obtain a
More informationSolid Click-Lock Bamboo Product Installation Instructions
Solid Click-Lock Bamboo Product Installation Instructions General The Valinge locking system is a revolutionary system for installing bamboo floors without using glue. However, it can be glued if necessary.
More informationHome Legend Uniclic Cork Product Installation Instructions
Home Legend Uniclic Cork Product Installation Instructions General Uniclic angle is a revolutionary system for installing cork floors without using glue. The panels can be clicked together simply, thanks
More informationWPC Vinyl Floor Installation Guide
WPC Vinyl Floor Installation Guide Introduction This guide will take you through the necessary steps to install your Bel-Air WPC Vinyl Flooring. Make sure to carefully read through this guide so that you
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR MIKASA TM REAL WOOD FLOORS These instructions are for all MIKASA TM real wood flooring products made using - - a unique and proven glue - less mechanism
More informationL. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only*
L. W. Mountain, Inc. Floating Glue Installation Instructions *For use with engineered floors only* Inspect the job site carefully before you begin the installation. Some conditions require specific installation
More informationPURE INSTALLATION MANUAL
INSTALLATION MANUAL Pure Click 40 is an LVT floor, designed for use in residential areas. Pure Click 55 is suited for both residential and commercial areas such as shops, hotel rooms, etc. To obtain a
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS HYDROCORK
INSTALLATION INSTRUCTIONS FOR WICANDERS HYDROCORK GENERAL INFORMATION Hydrocork floors are intended for indoor use only. Please read the following instructions before installation. Hydrocork connection
More informationWellmade. - Installation Guide. General Information. Pre-Installation
- Installation Guide Wellmade Wellmade WREW is a real wood veneer on a High Density Plastic Composite (HDPC ) flooring with patent pending technology. WREW is a Water Resistant Engineered Wood plank flooring
More informationALL DRAWINGS/ILLUSTRATIONS ARE LOCATED AT THE END OF THE INSTRUCTIONS.
Normandy Installation Instructions Planks are constructed with a joint that locks the planks together to form a tight, durable, water resistant joint. Normandy is installed as a floating floor so it's
More informationDeZignCore Ultra Luxury Vinyl Planks
DeZignCore Ultra Luxury Vinyl Planks v.7-17 Brushed Handscraped Southern Pecan 6 x 48 x 5.5mm DEDCU-162 $4.73/sf Auburn Oak 6 x 48 x 5.5mm DEDCU-921 $4.73/sf Maple 6 x 48 x 5.5mm DEDCU-630 $4.73/sf Hazelnut
More informationInstallation Procedure of Floating floors
SUBFLOOR PREPARATION OF WICANDERS FLOATING FLOORS WITH CORKLOC Wicanders floating floors with Corkloc can be installed in most domestic areas and in almost all commercial areas except in bathrooms, saunas
More informationNominal Bore. Max Pressure DN 2. 63,0 MPa. Nominal Bore. Max Pressure. 63,0 MPa DN 2. Nominal Bore. Max Pressure. 63,0 MPa DN 2.
MINIMESS an overvew MINIMESS -120 of screw- Nomnal Bore Max Pressure Materal Sealng materal Page M 1 x 2 DN 2 3,0 MPa Free-cuttng steel Stanless steel NBR (Perbunan) FKM (Vton) MINIMESS -p/t 120 of screw-
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
PLEASE READ THE ENTIRE BEFORE PROCEEDING WITH THE INSTALLATION OWNER / INSTALLER RESPONSIBILITY The installer assumes all responsibility for final inspection of product quality. Inspection of the entire
More informationInstallation Instruction Laminate Flooring
Installation Instruction Laminate Flooring Congratulations on the purchase of your new floor. We thank you for your excellent selection of an Eclipse product that is designed to offer you years of use
More informationPLEASE READ BEFORE INSTALLATION
PLEASE READ BEFORE INSTALLATION Comprehensive Installation and Maintenance Instructions It is important to work out of several cartons to mix the patterns when installing this select flooring product to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Dear customer, Thank you for buying our veneer Par-ky floor. Please read our installation instructions carefully. If these instructions are not followed, the installer will be
More informationTask: Review the section Materials and jointing techniques up to the heading Compression joints and answer the following questions.
CHAPER 1 ABRICAE AND INSALL NON-ERROUS PRESSURE PIPING 37 WORKSHEE 1 Student name: Enrolment year: Class code: Competency name/number: o be completed by teachers Satsfactory Not satsfactory WORKSHEES ask:
More informationSELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD
TOOLS AND MATERIALS SELECT SURFACES LAMINATE FLOORING INSTALLATION GUIDE DRIFTWOOD Vapor barrier (minimum 6 mil/0.15 mm) (if needed) Transitional moldings (if needed) Measuring tape Carpenter s square
More informationCovelo Canyon INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Covelo Canyon Prior to installation, installer should check material for appropriate grade, color, graining and finish quality. Installer should STOP THE JOB if any defects that
More informationIMPEC BAMBOO INSTALLTION MANUAL
IMPEC BAMBOO INSTALLTION MANUAL Please Read The Following Instruction Carefully Before Begin To Install Your Floor Thank You For Purchasing IMPEC BAMBOO General Info: The following guidelines and instructions
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS 5G-C FLOORS
INSTALLATION INSTRUCTIONS FOR WICANDERS 5G-C FLOORS GENERAL INFORMATION Wicanders 5G-C floors are intended for indoor use only. Please read the following instructions before installation. Store planks
More informationINSTALLATION INSTRUCTIONS FOR WICANDERS 2G FLOORS
INSTALLATION INSTRUCTIONS FOR WICANDERS 2G FLOORS GENERAL INFORMATION Wicanders 2G floors are intended for indoor use only. Please read the following instructions before installation. Store planks at room
More informationSolid Unfurled Bamboo Flooring Installation Instructions
Solid Unfurled Bamboo Flooring Installation Instructions WARRANTY COVERAGE MAY BE LOST DUE TO FAILURE TO STRICTLY ABIDE BY ALL INSTALLATION INSTRUCTIONS AND RECOMMENDATIONS IN THIS MANUAL. THIS INCLUDES
More informationYanchi Bamboo Flooring Installation Guide Pre-Installation Checklist Conditioning and Acclimating Your Bamboo Floor Before Installation
Yanchi Bamboo Flooring Installation Guide READ COMPLETELY BEFORE STARTING INSTALLATION. Congratulations on choosing Yanchi bamboo flooring. Please take time to read the following procedures before you
More informationWATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions
WATER TUFF VINYL FLOORING ATTENTION! READ BEFORE INSTALLING! Angle-Tap Installation Instructions FLOORING MATERIAL SHOULD BE INSPECTED PRIOR TO INSTALLATION Responsibility for the suitability of this flooring
More informationCOMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION
COMPOSITE (WPC) ENGINEERED VINYL FLOORING INSTALLATION PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE YOU BEGIN INSTALLATION! IMPROPER INSTALLATION WILL VOID WARRANTY. STOP! WPC Engineered Vinyl Flooring
More informationSTONE PRODUCT COMPOSITE (SPC) FLOORING INSTALLATION INSTRUCTIONS
Read all instructions before installing. Incorrect installation will invalidate and void warranty. IMPORTANT Goodfellow Dubaï is guaranteed for use only as a floor covering. Goodfellow Dubaï is intended
More informationCenterStone Collection Installation Guide
CenterStone Collection Installation Guide 2 SPC Installation Instructions Thank you for choosing our product. When properly installed and cared for, your new flooring will be easy to maintain and will
More information