Installation Manual. For the competent person. Installation Manual. Flue pipe for ecotec plus. Concentric Ø 110/160 GB, IE

Transcription

1 Installaton Manual For the competent person Installaton Manual Flue ppe for ecotec plus Concentrc Ø 0/60 GB, IE

2 Table of contents Table of contents Notes on the documentaton...3. Observng other applcable documents...3. Storng documents Applcablty of the nstructons...3 Safety.... Classfcaton of acton-related warnngs.... General safety nformaton....3 Intended use...5. Regulatons CE label Installaton dmensons...6 System overvew of concentrc system Ø 0/60 mm Installaton optons Product range Elements Descrpton of elements... 5 System condtons Maxmum ppe lengths Performance features of the flue ppes from Vallant for condensng unts Requrements for the shaft for the flue ppe Locaton of the openng Dsposng of condensate Route of the flue ppe n the buldng Installaton of the vertcal roof duct Installaton nstructons Installng the roof duct Black or red roof duct Stanless steel roof duct Installng the concentrc connecton to the ar/ flue gas system (LAS): Installng the flue gas ppes n the shaft General nformaton for shaft openngs of flue gas ppes next to another flue gas nstallaton Installng the rgd flue gas ppe System dagram Installng the flue gas ppe Installng a shaft extenson Installng the PP shaft extenson Installng the stanless steel PP shaft extenson Installng the flue gas ppe on a support ppe Installng the flexble flue gas ppe Scope of delvery Installng the flexble flue gas ppe Installng the shaft cover Installng the horzontal flue gas ppe and the ar ppe Prncple of ar supply through the external wall (concentrc system) Scope of delvery Connectng the ar ntake to the unt Installng the ar ntake pece Installng the ar supply through the external wall 0 Installng the flue gas ppe on the external wall System dagram Statc dmensons Installng the flue gas ppe Installaton nstructons Installng the connecton for the external wall ppe Installng the clamps Installng the roof duct Shortenng an extenson...7 Installng the horzontal wall duct System dagram Installng the wall duct Installng the horzontal wall duct... 8 Installng the horzontal flue gas ppe Ø 0 mm Installaton nstructons Installng the horzontal flue gas ppe Installng the horzontal flue gas ppe Ø 0/60 mm Installaton nstructons Installng the horzontal flue gas ppe Customer servce Index...57 Installaton manual for the flue ppe for ecotec plus _0

3 Notes on the documentaton Notes on the documentaton. Observng other applcable documents For the competent person: Installaton nstructons for the nstalled gas-fred boler.. Storng documents > Please pass on ths nstallaton manual and all other applcable documents and auxlary equpment to the plant operator. The system operator wll store these nstructons as well as any auxlary materals so that they are avalable when requred..3 Applcablty of the nstructons Ths nstallaton manual apples only for the Vallant unts named n the other applcable documents. Installaton manual for the flue ppe for ecotec plus _0 3

4 a Safety a Safety. Classfcaton of acton-related warnngs The acton-related warnngs are classfed n accordance wth the severty of the possble danger usng the followng warnng symbols and sgnal words: Warnng symbol Sgnal word a Danger! e Danger! a Warnng. b Cauton.. Meanng of warnng symbols Explanaton. General safety nformaton Immnent danger to lfe or rsk of severe personal njury Rsk of death from electrc shock Rsk of mnor personal njury Rsk of materal or envronmental damage > Before nstallng the flue ppe, you must nform the local gas supply company and the master chmney sweep for the dstrct. Qualfcaton of the competent persons The nstallaton of the boler and ts flue must be carred out by a competent person approved at the tme by the Health and Safety Executve. Ths competent person s also responsble for proper executon. They must also comply wth the exstng drectves, regulatons and gudelnes. Dangers caused by flue gas ext n the event of mproper nstallaton. In the event of mproper nstallaton, there s a rsk that posonous gases may be emtted. > Ensure that the nstallaton s performed only by qualfed competent persons. Rsk of death by posonng due to escapng flue gases! All openngs n the flue ppe that can be opened for nspecton purposes must be closed before start-up and durng operaton. > The openngs must only be opened by a competent person. For open-flued operaton, the unt must not be placed n rooms from whch the ar s extracted usng fans (for example, ventlaton systems, extractor hoods, tumble dryer ventlaton). These systems generate negatve pressure n the room. Ths negatve pressure can cause flue gas to be sucked nto the nstallaton room from the openng through the annular clearance between the flue gas ppe and the shaft. The unt can be used n open-flued operaton f smultaneous operaton of the unt and the fan s not possble. Avod rsk of suffocaton! If the flue gas ppe s not concentrc and s therefore not ventlated from behnd, there s a danger of suffocaton n unventlated rooms. > These rooms must be equpped wth a ventlaton openng of 50 cm that leads nto the fresh ar. Prevent njures caused by snow fallng from roofs Where flue ppes penetrate the roof skn, the water vapour contaned n flue gas may precptate as ce on the roof or the roof structures n unfavourable weather condtons. > At the nstallaton ste, ensure that ths ce buld-up does not slde from the roof. Use of tools Unsutable tools or the mproper use of tools can cause damage (e. g. to casng and components). > Always use approprate screwdrvers or open-end spanners (fork wrenches) to loosen or tghten threaded connectons. > Never use ppe wrenches, extensons, or other smlar tools. Preventng the rsk of corroson n the flue gas nstallaton Sprays, solvents, cleanng agents, pants and adhesves may contan substances that could lead to corroson n the flue gas nstallaton n some crcumstances when the unt s n operaton. > Only use approprate Vallant components for nstallng the flue gas gudng. > Ensure that the combuston ar that s guded to the unt s kept free of chemcal substances that could contan, e. g. fluorne, chlorne, or sulphur. Preventng electronc damage and rsk of fre caused by lghtnng The unt can be damaged by the effects of lghtnng. > If the buldng s equpped wth a lghtnng protecton system, ncorporate the ar/flue gas ppe nto the lghtnng protecton. > If the vertcal flue gas ppe contans materals made from metal, ncorporate t nto the potental balancng. Installaton manual for the flue ppe for ecotec plus _0

5 a Safety a Malfunctons of the unt due to obstructon of the flue gas flow! If chppngs, mortar resdue, or smlar objects enter the flue ppe, the functon of the unt may be affected. > Durng nstallaton, ensure that no chppngs, mortar resdue, etc. reman n the flue ppe. Malfunctons and condensaton ext due to lack of tghtness n the flue gas route! The seals are senstve to mneral-ol-based grease. > If necessary, use ether water or the lubrcant provded. Fre protecton Outsde the shaft, the flue gas ppes that are not n a concentrc desgn must have a mnmum clearance of 5 cm to combustble components. In chmneys formerly used for ol or sold fuels, whch are now to be used for the supply of combuston ar, t s recommended that the chmney sweep nspects and cleans the flue n queston before the flue gas ppe s nstalled. If t s not possble to adequately clean or nspect the chmney (e. g. due to constructon features), you can use a separated ar supply or use open-flued operaton for the system.. Regulatons Observe the natonal regulatons, standards, gudelnes and laws..5 CE label The Vallant ecotec gas-fred wall-hung bolers are certfed accordng to the EU gas applances drectve 009//EC as a boler system wth assocated flue gas nstallaton. Ths nstallaton manual s a part of the certfcaton and s cted n the type testng certfcate. In complance wth the regulatory statutes of ths nstallaton manual, the proof of usablty of the products dentfed by Vallant artcle numbers that are desgned for the flue ppe s provded. If you do not use certfed elements for the Vallant flue ppe when nstallng Vallant ecotec gas-fred wall-hung bolers, ths vods the CE conformty of the unt. We therefore strongly recommend that you ft Vallant ar/flue gas systems. It s not necessary to leave a clearance between the concentrc flue ppe or the correspondng extenson and components made from combustble materals, because, at the nomnal heat output of the unt, components borderng the surface cannot reach temperatures hgher than 85 C..3 Intended use The Vallant flue ppes for ecotec plus are constructed usng state-of-the-art technology n accordance wth the recognsed safety rules and regulatons. Nevertheless, there s stll a rsk of death or serous njury to the user or others or of damage to the unt and other property n the event of mproper use or use for whch the unt s not ntended. The Vallant flue ppes named n ths manual must only be used n combnaton wth the unt types named n ths manual. Any other, or addtonal use s consdered mproper use and all responsblty or lablty of the manufacturer/suppler for any resultng damages s excluded. In ths case, the responsble competent person and the user bear the rsk. Intended use ncludes the followng: observance of accompanyng operatng, nstallaton and servcng nstructons for Vallant products as well as for other parts of components of the system nstallng and fttng the boler n accordance wth the boler and system approval complance wth all nspecton and mantenance condtons lsted n the nstructons. Installaton manual for the flue ppe for ecotec plus _0 5

6 3 Installaton dmensons 3 Installaton dmensons Installaton dmensons 6 Installaton manual for the flue ppe for ecotec plus _0

7 System overvew of concentrc system Ø 0/60 mm System overvew of concentrc system Ø 0/60 mm. Installaton optons Requred art. no. *) (black) (red) Type of nstallaton Vertcal roof duct: concentrc ar/flue gas ppe through the roof Installaton nstructons Maxmum ppe lengths: secton 5. Installng the vertcal roof duct: secton 6 Rgd: and or Flexble: and and Concentrc connecton to shaft Flue gas ppe n the shaft Combuston ar from the shaft Maxmum ppe lengths: secton 5. Installng the rgd flue gas ppe n the shaft: secton 8. Installng the flexble flue gas ppe n the shaft: secton 8.3 Installng the horzontal flue gas ppe: secton 3 Rgd: and and or Flexble: and and and Concentrc connecton to the shaft Flue gas ppe n the shaft Combuston ar from the nstallaton room Maxmum ppe lengths: secton 5. Installng the rgd flue gas ppe n the shaft: secton 8. Installng the flexble flue gas ppe n the shaft: secton 8.3 Installng the horzontal flue gas ppe: secton 3. Installaton optons (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0 7

8 System overvew of concentrc system Ø 0/60 mm Requred art. no. *) Rgd: and or Flexble: and and Type of nstallaton Concentrc connecton to the shaft Flue gas ppe n the shaft Combuston ar through the external wall Installaton nstructons Maxmum ppe lengths: secton 5. Installng the rgd flue gas ppe n the shaft: secton 8. Installng the flexble flue gas ppe n the shaft: secton 8.3 Installng the horzontal flue gas ppe: and the ar ppe: secton 9 Rgd: and or Connecton to the shaft Flue gas ppe n the shaft Combuston ar from the nstallaton room Maxmum ppe lengths: secton 5. Installng the rgd flue gas ppe n the shaft: secton 8. Installng the horzontal flue gas ppe: secton Concentrc connecton to the flue gas ppe on the external wall Combuston ar from outsde Maxmum ppe lengths: secton 5. Installng the flue gas ppe on the external wall: secton 0 Installng the horzontal flue gas ppe: secton 3. Installaton optons (contnued on next page) 8 Installaton manual for the flue ppe for ecotec plus _0

9 System overvew of concentrc system Ø 0/60 mm Requred Type of nstallaton art. no. *) Concentrc horzontal wall duct Installaton nstructons Maxmum ppe lengths: secton 5. Installng the horzontal wall duct: secton Installng the horzontal flue gas ppe: secton wth Concentrc connecton to vertcal shaft system Maxmum ppe lengths: secton 5. Installng the concentrc connecton to the ar/flue gas system (LAS): secton 7 *) for addtonal flue components, see secton.. Installaton optons (contnued) Installaton manual for the flue ppe for ecotec plus _0 9

10 System overvew of concentrc system Ø 0/60 mm. Product range Product range Art. no. Column (see Table "Elements") Vertcal roof duct, black (RAL 9005) Vertcal roof duct, red (RAL 803) A Horzontal wall/roof duct B Concentrc connecton to flue gas ppe n shaft, room-sealed Concentrc connecton to flue gas ppe n shaft, open-flued wth C Concentrc connecton to flexble flue gas ppe n shaft, room-sealed wth Concentrc connecton to flexble flue gas ppe n shaft, room-sealed wth ar supply through the external wall wth Concentrc connecton to flexble flue gas ppe n shaft, open-flued wth and Concentrc connecton to flue gas ppe n shaft, room-sealed wth ar supply through the external wall E Connecton to flue gas ppe, concentrc, for layng on external wall F Connecton to ar/flue gas system (LAS) wth G Support elbow Ø 0 mm, PP, wth mountng ral H D. Product range.3 Elements Elements Art. no. A B C D E F G H Extensons, concentrc 0.5 m, Ø 0/60, PP X X X X X X X Extensons, concentrc.0 m, Ø 0/60, PP X X X X X X X Extensons, concentrc.0 m, Ø 0/60, PP Elbow 5, concentrc (x ), Ø 0/60, PP X X X X X X X X X X X X X X Elbow 87, concentrc Ø 0/60, PP X X X X X X X. Elements (contnued on next page) 0 Installaton manual for the flue ppe for ecotec plus _0

11 System overvew of concentrc system Ø 0/60 mm Elements Art. no. A B C D E F G H Fastenng clamps wth bolts and rawl plugs (5 pcs), Ø X X X X X X X Cleanng eye, concentrc, 0/60, PP X X X X X X X Cleanng T-pece 87 (or cleanng elbow), concentrc, Ø 0/60, PP X X X X X X X Extensons, concentrc 0.5 m, Ø 0, PP X X X Extensons, concentrc.0 m, Ø 0, PP X X X Extensons, concentrc.0 m, Ø 0, PP X X X Extenson wth cleanng eye, Ø 0, PP X X X Elbow 5, Ø 0, PP X X X Elbow 30, Ø 0, PP X X X Elbow 5, Ø 0, PP X X X Cleanng T-pece 87 or cleanng elbow, concentrc, Ø 0, PP X Spacer (0 pcs), for shaft 0 cm x 0 cm Ø X X X Fastenng clamps for flue ppe Ø 0, PP X Wall collar, Ø X. Elements (contnued) Installaton manual for the flue ppe for ecotec plus _0

12 System overvew of concentrc system Ø 0/60 mm Elements Art. no. A B C D E F G H Shaft extenson, plastc, Ø X X X Shaft extenson, stanless steel, Ø 0 External wall bracket (adjustable 50 to 90 mm clearance), stanless steel Extenson for external wall bracket (adjustable 90 to 80 mm clearance), stanless steel 0.5 m extenson for external wall layng, concentrc, nteror PP, exteror stanless steel.0 m extenson for external wall layng, concentrc, nteror PP, exteror stanless steel X X X X X X X 5 elbow for external wall layng ( pcs), concentrc, nteror PP, exteror stanless steel X 30 elbow for external wall layng ( pcs), concentrc, nteror PP, exteror stanless steel X Cleanng pece for external wall layng, concentrc, nteror PP, exteror stanless steel X Roof duct conc., 000 mm wth ran penetraton collar, Ø 0/ X Ar clamp for Ø 0/60, stanless steel Adapter pece from Ø 0 on spgot end Ø X X Flexble flue gas ppe, 7.5 m roll X Flexble flue gas ppe, 5 m roll X Flexble flue gas ppe, 5 m roll X Inspecton element X. Elements (contnued) Installaton manual for the flue ppe for ecotec plus _0

13 System overvew of concentrc system Ø 0/60 mm Elements Art. no. A B C D E F G H Installaton set (nstallaton cone and lne) X Connectng element X Spacer (7 pcs) X Basc connecton kt, shaft nstallaton wth shaft cover, PP X Ptched roof tle 5-50, flexble, black (RAL 9005) X X Ptched roof tle 5-50, flexble, red (RAL 803) X X Flat roof penetraton collar X X. Elements (contnued) Installaton manual for the flue ppe for ecotec plus _0 3

14 System overvew of concentrc system Ø 0/60 mm. Descrpton of elements Name Art. no. Elements Extensons concentrc, Ø 0/60, PP: m -.0 m -.0 m / 000 / Ø60 Ø0 Ø0 Ø6 Elbow 5 concentrc ( pcs), Ø 0/60, PP Ø75 73 Ø0 Ø60 Elbow 87 Concentrc, Ø 0/60, PP Ø0 Ø60 Fastenng clamps wth bolts and rawl plugs (5 pcs), Ø 0 mm Cleanng eye Concentrc, Ø 0/60, PP Ø0 Ø Descrpton of elements (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0

15 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Cleanng T-pece 87 (or cleanng elbow) concentrc, Ø 0/60, PP Ø Ø0 Ø60 Ar ntake pece Concentrc, Ø 0/60, PP Extensons Ø 0, PP m -.0 m -.0 m Ø0 500 / 000 / 000 Extenson wth cleanng eye, Ø Ø Elbow 5 Ø 0, PP Ø7 Ø 56 Ø0 3 Elbow 30, Ø 0, PP Ø7 77 Ø0 8.3 Descrpton of elements (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0 5

16 Ø 0 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Elbow 5 Ø 0, PP Cleanng T-pece 87 (or cleanng elbow) Ø 0, PP Wnd protecton for horzontal flue openng Ø No mage Spacer (0 pcs) for shaft 0 cm x 0 cm, Ø Fastenng clamps for flue ppe made from PP Ø Wall collar Ø Descrpton of elements (contnued on next page) 6 Installaton manual for the flue ppe for ecotec plus _0

17 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Shaft extenson Plastc, Ø Shaft extenson stanless steel, Ø External wall bracket (adjustable 50 mm to 90 mm clearance), stanless steel Extenson for external wall bracket (adjustable 90 to 80 mm clearance), stanless steel Descrpton of elements (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0 7

18 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Extenson for external wall layng concentrc, nteror PP, exteror stanless steel, Ø 0/60, 0.5 m Ø60 Ø Extenson for external wall layng concentrc, nteror PP, exteror stanless steel, Ø 0/60,.0 m Ø60 Ø Elbow 5 for external wall layng ( pcs) concentrc, nteror PP, exteror stanless steel, Ø 0/ Ø60 Ø Ø0 60,5 Elbow 30 for external wall layng ( pcs), concentrc, nteror PP, exteror stanless steel, Ø 0/ Ø60 Ø Ø Descrpton of elements (contnued on next page) 8 Installaton manual for the flue ppe for ecotec plus _0

19 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Cleanng pece for external wall layng concentrc, nteror PP, exteror stanless steel, Ø 0/ Ø60 Ø0 Ø Roof duct 000 mm wth ran penetraton collar, concentrc, Ø 0/ Ø60 Ø0 Ø78 Ø0 Ø Ptched roof tle 5-50 flexble, black (RAL 9005) red (RAL 803) x 500 Flat roof penetraton collar Ø 7 30 Ø 7 Support elbow Ø 0 wth mountng ral Ø0 Ø Descrpton of elements (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0 9

20 System overvew of concentrc system Ø 0/60 mm Name Art. no. Elements Vertcal roof duct concentrc, mountng bar, length above roof approx..5 m, length below roof approx. 0.5 m - Roof duct Ø 0/60, wth slder - Rafter mountng - Cover plate Black: Red: Horzontal wall/roof duct Concentrc, wth 87 cleanng T-pece or cleanng elbow and wall collars Concentrc connecton to flue gas ppe n shaft - Inspecton elbow conc. DN0/60, Vallant whte - Ppe conc. DN0/60 x 0.5 m, Vallant whte - Support DN0 wth elbow and mountng ral - Cover plate DN60, steel Connecton to flue gas ppe, concentrc, for layng on external wall - Inspecton elbow conc., Ø 0/60, 87 Vallant whte - Ppe conc. DN0/0/60 x 0.5 m, Vallant whte - Wall duct, Ø 0/60, 0.5 m - External wall console, Ø 0/60 - Cover plate, Ø 60, stanless steel - Cover plate, Ø 60, steel - Supply ar supports, conc., Ø 0/60 - Openng cover, Ø 0/ Basc connecton set for separate ar supply 0/60 - Intake grlle ( pcs) - Wall panel - Concentrc T-pece for the ar supply n the conc. annular gap - Concentrc ppe wth seal for supply ppe on the sleeve, 50 mm long - Support elbow wth mountng ral Descrpton of elements (contnued) 0 Installaton manual for the flue ppe for ecotec plus _0

21 System condtons 5 5 System condtons 5. Maxmum ppe lengths Elements Vertcal roof duct Horzontal wall/roof duct Connecton to ar/flue gas system (LAS) Concentrc connecton to flue gas ppe Ø 0 (rgd) n shaft Mn. shaft cross-secton: - round: 70 mm - angular: 50 x 50 mm Open-flued Conc. connecton to flue gas ppe Ø 00 (flexble) n shaft Shaft cross-secton mn.: - round: 80 mm - angular: 60 x 60 mm Open-flued Art. no Max. concentrc ppe length Max. concentrc ppe length Max. concentrc ppe length (horzontal secton) Max. concentrc ppe length (horzontal secton) Max. length of flue gas ppe Ø 0 n shaft Max. concentrc ppe length (horzontal secton) Max. length of flue gas ppe Ø 00 n shaft ecotec plus VU GB 806/5-5 VU GB 006/5-5 VU GB 06/5-5 m plus x 87 elbows 0 m plus x 87 elbows m plus x 87 elbows If addtonal dversons are arranged n the flue gas nstallaton, the maxmum ppe length s reduced as follows: - by.5 m for each 87 dverson - by.0 m for each 5 dverson - by.5 m for each nspecton T-pece m plus x 87 elbow 8 m plus x 87 elbow 9 m plus x 87 elbow If addtonal dversons are arranged n the flue gas nstallaton, the maxmum ppe length s reduced as follows: - by.5 m for each 87 dverson - by.0 m for each 5 dverson - by.5 m for each nspecton T-pece.0 m plus 3 x 87 elbows.0 m plus 3 x 87 elbows.0 m plus 3 x 87 elbows The chmney sweep approvals must be observed. The dmensons of the chmney must comply wth the manufacturer's specfcatons. 3.0 m plus x 87 elbow and 3.0 m plus x 87 elbow and.0 m plus x 87 elbow and 50 m 50 m 9 m Of whch maxmum 5 m n cold area. If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by 6 m for each 87 dverson by m for each 5 dverson by 8 m for each nspecton T-pece by m for each m extenson 6.0 m plus x 87 elbow and 6.0 m plus x 87 elbow and.0 m plus x 87 elbow and 30.0 m 30.0 m 6.0 m Of whch maxmum 5 m n cold area. If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum horzontal ppe length s reduced as follows: - by.5 m for each 87 dverson - by.0 m for each 5 dverson - by.5 m for each nspecton T-pece If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by 6 m for each 87 dverson by m for each 5 dverson by 8 m for each nspecton T-pece by m for each m extenson 5. Maxmum ppe lengths ecotec plus (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0

22 5 System condtons Elements Concentrc connecton to flue gas ppe Ø 0 (rgd) n shaft Shaft cross-secton mn.: - round: 70 mm - angular: 50 x 50 mm room-sealed n combnaton wth separate ar supply Separate ar supply Concentrc connecton Ø 0/60 to flue gas ppe Ø 00 (flexble) n shaft Shaft cross-secton mn.: - round: 80 mm - angular: 60 x 60 mm Room-sealed n combnaton wth separate ar supply Art. no Max. flue gas total ppe length (concentrc part and flue gas ppe Ø 0 n the shaft) Max. ppe length for supply lne Ø 0/ Max. concentrc ppe length (horzontal secton) Max. ppe length Ø 00 n shaft ecotec plus VU GB 806/5-5 VU GB 006/5-5 VU GB 06/ m plus x 87 elbow and 5 m plus x 87 elbow 50.0 m plus x 87 elbow and Of whch maxmum 5 m n cold area. If addtonal dversons are arranged n the flue gas nstallaton, the maxmum ppe lengths are reduced as follows: by. m for each 87 dverson by 0.6 m for each 5 dverson by m for each nspecton T-pece 5 m plus x 87 elbow 3.0 m plus x 87 elbow and 5 m plus x 87 elbow If addtonal extensons or dversons are arranged n the supply ar, the maxmum supply ppe lengths or flue gas total ppe lengths are reduced as follows: by. m for each 87 dverson by 0.6 m for each 5 dverson by m for each nspecton T-pece by. m for each m extenson.0 m plus x 87 elbow and.0 m plus x 87 elbow and.0 m plus x 87 elbow and 9 m 5 m 5 m Of whch maxmum 5 m n cold area. If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by. m for each 87 dverson by 0.6 m for each 5 dverson by m for each nspecton T-pece Separate ar supply Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) n shaft Shaft cross-secton mn.: - round: 55 mm - angular: 0 x 0 mm Room-sealed Max. ppe length for supply lne Ø 0/ Max. total ppe length (concentrc part and flue gas ppe Ø 0 n shaft) 5 m plus x 87 elbow 5 m plus x 87 elbow 5 m plus x 87 elbow If addtonal extensons or dversons are arranged n the supply ar, the maxmum supply ppe lengths or flue gas total ppe lengths are reduced as follows: by.5 m for each 87 dverson by.0 m for each 5 dverson by m for each nspecton T-pece by m for each m extenson Ø 0: 7 m Ø 00: 9.5 m plus x 87 elbow and Ø 0: 3 m Ø 00: 7.5 m plus x 87 elbow and Ø 0: 7.5 m Ø 00:.5 m plus x 87 elbow and If addtonal dversons are arranged n the flue gas nstallaton, the maxmum ppe length s reduced as follows: by.5 m for each 87 dverson by.0 m for each 5 dverson by.5 m for each nspecton T-pece 5. Maxmum ppe lengths for ecotec plus (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0

23 System condtons 5 Elements Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) Shaft cross-secton: - round: 70 mm - angular: 50 x 50 mm Room-sealed Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) n shaft Shaft cross-secton mn.: - round: 80 mm - angular: 60 x 60 mm Room-sealed Art. no Max. conc. ppe length (horzontal part) Max. ppe length n shaft Max. conc. ppe length (horzontal part) Max. ppe length n shaft ecotec plus VU GB 806/5-5 VU GB 006/5-5 VU GB 06/5-5 m plus x 87 elbow and Ø 0: 3 m Ø 00: m m plus x 87 elbow and Ø 0: 5 m Ø 00: 8 m m plus x 87 elbow and Ø 0: 3 m Ø 00: 9 m If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: By m for each 87 elbow By m for each 5 elbow By 3 m for each nspecton T-pece By m for each m extenson m plus x 87 elbow and Ø 0: 5 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 3 m Ø 00: 7 m m plus x 87 elbow and Ø 0: 8 m Ø 00: m If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by 3 m for each 87 dverson by m for each 5 dverson by m for each nspecton T-pece by m for each m extenson Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) n shaft max. conc. ppe length (horzontal part) m plus x 87 elbow and m plus x 87 elbow and m plus x 87 elbow and Shaft cross-secton: - round: 90 mm - angular: 70 x 70 mm Room-sealed Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) n shaft Shaft cross-secton: - round: 00 mm - angular: 80 x 80 mm Room-sealed Max. ppe length n shaft max. conc. ppe length (horzontal part) Max. ppe length n shaft Ø 0: 50 m Ø 00: 30 m Ø 0: m Ø 00: 30 m Ø 0: 5 m Ø 00: 8.5 m Of whch maxmum 5 m n cold area. If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by m for each 87 dverson by 3 m for each 5 dverson by 5 m for each nspecton T-pece by 3 m for each m extenson m plus x 87 elbow and Ø 0: 50 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 8 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 7 m Ø 00: m If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by m for each 87 dverson by 3 m for each 5 dverson by 5 m for each nspecton T-pece by 3 m for each m extenson 5. Maxmum ppe lengths for ecotec plus (contnued on next page) Installaton manual for the flue ppe for ecotec plus _0 3

24 5 System condtons Elements Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) n shaft Shaft cross-secton of - round: 0 mm - angular: 90 x 90 mm Room-sealed Concentrc connecton to flue gas ppe Ø 0 (Ø 00 flexble) Shaft cross-secton: - round: 0 mm - angular: 00 x 00 mm Room-sealed Connecton to flue gas ppe on the external wall Art. no max. conc. ppe length (horzontal part) Max. ppe length n shaft max. conc. ppe length (horzontal part) max. ppe length DN 0 n shaft Max. concentrc ppe length up to ar ntake ecotec plus VU GB 806/5-5 VU GB 006/5-5 VU GB 06/5-5 m plus x 87 elbow and Ø 0: 50 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 50 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 9 m Ø 00: m If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by 6 m for each 87 dverson by m for each 5 dverson by 8 m for each nspecton T-pece by m for each m extenson m plus x 87 elbow and Ø 0: 50 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 50 m Ø 00: 30 m m plus x 87 elbow and Ø 0: 3 m Ø 00: 6 m If addtonal dversons are arranged n the horzontal part of the flue gas nstallaton, the maxmum length n the shaft s reduced as follows: by 6 m for each 87 dverson by m for each 5 dverson by 8 m for each nspecton T-pece by m for each m extenson 3 m plus 3 x 87 elbows and 3 m plus x 87 elbow and m plus x 87 elbow and If addtonal extensons/dversons are arranged n the concentrc part of the flue gas nstallaton, the maxmum length of the flue gas ppe on the external wall s reduced as follows: by 5.3 m for each 87 dverson by 3. m for each 5 dverson by 8 m for each nspecton T-pece by 3. m for each m extenson Connecton to flue gas ppe DN 0 n shaft Mn. shaft cross-secton: - round: 70 mm - angular: 50 x 50 mm Open-flued max. ppe length on the external wall max. total ppe length (horzontal flue gas ppe and flue gas ppe n shaft) 50 m 50 m 9 m If addtonal dversons are arranged n the flue gas ppe on the external wall, the maxmum length s reduced as follows: by m for each 87 dverson by 0.5 m for each 5 dverson 50.0 m plus x 87 elbow and 50.0 m plus x 87 elbow and 0.0 m plus x 87 elbow and If addtonal dversons are arranged n the flue gas nstallaton, the maxmum ppe length s reduced as follows: - by.0 m for each 87 dverson - by 0.5 m for each 5 dverson - by.5 m for each nspecton T-pece 5. Maxmum ppe lengths ecotec plus (contnued) Installaton manual for the flue ppe for ecotec plus _0

25 System condtons 5 5. Performance features of the flue ppes from Vallant for condensng unts The ar/flue gas systems from Vallant demonstrate the followng performance features: Performance feature Temperature resstance: Leak-tghtness: Condensate resstance: Corroson resstance: Clearance from combustble materals: Installaton ste: Resstance to fre: Fre resstance tme: 5. Performance features Descrpton Adapted to the maxmum flue gas temperature of the unt Adapted to the unt for use n buldngs and outdoors Yes, for gas and ol Adapted to the gas and ol condensng boler - Concentrc flue gas ppe: No clearance requred - Non-concentrc flue gas ppe: 5 cm In accordance wth the nstallaton nstructons Normal level of flame resstance (n accordance wth EN 350- Class E) No, the external ppes of the concentrc system are not flammable. A requred fre resstance tme s provded by shafts wthn the buldng. 5.3 Requrements for the shaft for the flue ppe Flue ppes from Vallant do not have any fre resstance (drecton of operaton from the outsde to the nsde). If the flue ppe s guded through parts of a buldng that requre a level of fre resstance, a shaft must be ftted. The shaft must ensure the fre resstance (drecton of operaton from the outsde to the nsde) that s requred for the buldng parts through whch the flue gas nstallaton s guded. The requred fre resstance must demonstrate a sutable classfcaton (brck partton and heat nsulaton) and be suffcent for the buldng's requrements. Observe the natonal ordnances, regulatons and standards. An exstng chmney that was used for the flue gas evacuaton usually meets these requrements and can be used as a shaft for the flue ppe. The gas tghtness of the shaft must comply wth the test pressure class N n accordance wth EN 3. An exstng chmney that was used for the flue gas evacuaton usually meets these requrements and can be used as a shaft for the ar gudng. If the shaft s used to supply combuston ar, ths must be desgned and, n partcular, nsulated n such a way that no mosture (caused by the coolng of the shaft by cold combuston ar penetratng from the outsde) can penetrate the exteror of the shaft. An exstng chmney that was used for the flue gas evacuaton usually meets these requrements and can be used as a shaft for the ar gudng wthout the need for addtonal heat nsulaton. 5. Locaton of the openng Algn the openng of the flue gas nstallaton n such a way that ensures a secure outward flow and dstrbuton of the flue gases and prevents these gases from re-enterng the buldng through openngs (wndows, ar ntake openngs and balcones). The locaton of the flue gas nstallaton openng must comply wth the relevant applcable nternatonal, natonal and/ or local regulatons. 5.5 Dsposng of condensate When dsposng of the condensate nto the publc wastewater system, observe the local regulatons. Local regulatons may stpulate the mnmum qualty of any condensate that may enter the waste-water system, for example, through usng a condensate neutralser. Only use corroson-resstant ppng materal for removng condensate. 5.6 Route of the flue ppe n the buldng The route of the flue ppe should correspond to the shortest and the most drect dstance between the unt and the flue gas nstallaton openng, and t should run as straght as possble. Do not arrange several dversons mmedately after each other. Lay the flue ppe separately from the drnkng water ppes. As a result of standards relatng to the hygene of drnkng water, water ppes must be protected aganst mpermssble heatng. The entre length of the flue gas route must be nspected and, f requred, cleaned. It must be possble to remove the flue ppe agan wth a mnmal amount of effort (no tme-consumng mortsng work n the lvng area, but screwed-n claddng nstead). If they are arranged n shafts, they are usually easy to remove. Installaton manual for the flue ppe for ecotec plus _0 5

26 6 Installaton of the vertcal roof duct 6 Installaton of the vertcal roof duct 6. Installng the roof duct 6. Installaton nstructons 6.. Black or red roof duct You can also use the roof ducts of the external wall system (stanless steel). b Cauton. Rsk of damage to the unt. Very damp ar escapes from the channel vents. Ths can condense n the ar ppe and cause damage to the unt. > Observe the requrements for mnmum clearances n ( Fg. 6.) H 0 3 m m 6. Installng the roof duct 3 m 6. Installaton ste of the roof duct The nstallaton s descrbed usng an example of a ptched roof. For a flat roof, use the flat roof penetraton collar (6) nstead of the flat roof penetraton collar (). > Insert the unversal tle () n the roof. > Insert the top part of the tle for vertcal algnment of the roof duct. > Insert the vertcal roof duct () nto the ptched roof tle () or the flat roof penetraton collar from above. The ran penetraton collar and the top part of the tle must form a ranproof seal. > Algn the roof duct vertcally and secure the clamp (3) to a rafter or to the celng. > Fll the gap between the roof duct and the roof or celng constructon wth nsulatng materal. > Screw the rosette ppe trm (vapour barrer) () to the celng. For a better seal, slcone may be used between the flange and the celng. 6 Installaton manual for the flue ppe for ecotec plus _0

27 Installaton of the vertcal roof duct 6 You can shorten the roof duct f necessary. 6.. Stanless steel roof duct Always shorten the nteror and exteror ppes by an equal amount. The slder (5) facltates a smple connecton between the roof duct and unt connecton. The slder has a maxmum usable length of 500 mm. Ths does not requre shortenng, because t sldes telescopcally nto the roof duct. > Insert the slder nto the roof duct. > If necessary, shorten the flue ppe > Place the flue ppe and the sleeve on the flue ppe of the roof duct. > Slde the flue ppes nto the roof duct. > Insert the flue ppes nto the equpment connecton pece from above. > Remove the slder from the roof duct. > Insert the slder nto the sleeve of the equpment connecton pece. > If necessary, use concentrc extensons and dversons. > Secure all connectng ponts wth a safety screw as descrbed n secton Stanless steel roof duct Key Roof duct Fastenng clamp 3 External ppe of the roof duct Internal ppe of the roof duct 5 Connectng sleeve In order to shorten the roof duct, you must frst remove the connectng sleeve. > Pull the connectng sleeve (5) from the external ppe (3). The connectng sleeve s no longer requred. > Shorten the external ppe and flue ppe by an equal dstance. > Place the roof duct on the ptched roof tle or flat roof penetraton collar. > Ft the ar ntake pece and the openng cover, along wth the requred clamps, to the upper end of the roof duct. For the ar ntake pece and openng cover, you must use the artcle number > Attach the fastenng clamps of the roof duct to the rafters or to the celng. For the area above the roof, refer to secton 0 (roof duct n external wall system). > Contnue as descrbed n secton 6.. (black or red roof duct). Installaton manual for the flue ppe for ecotec plus _0 7

28 7 Installng the concentrc connecton to the ar/flue gas system (LAS): 7 Installng the concentrc connecton to the ar/flue gas system (LAS): A B You requre at least: the cleanng T-pece 87 Ø 0/60 mm (artcle number ) an extenson Ø 0/60 mm (artcle number ) a Danger! Rsk of posonng due to escapng flue gas! Standng condensate can damage the seals of the flue gas ppe. > Lay the horzontal flue ppe wth a downward gradent of 3 nwards. 3 corresponds to a downward gradent of approx. 50 mm per metre of ppe length. a Danger! Rsk of posonng due to escapng flue gas! In the event of overpressure n the vertcal part of the flue gas ppe, flue gas may flow nto a unt that s not operatng. The unts are not sutable for ths mode of operaton and are not checked. > Provde evdence of the functonal relablty of the vertcal flue gas ppe n accordance wth EN 338 usng the specfcatons for flue gas temperature and flue gas mass rate from the nstallaton nstructons for the unt. a Danger! Rsk of njury due to damage to the structural ntegrty. The statc functon and fre-protectve functon of the shaft wall may be mpared and may lead to a hazard to persons. > Do not attach any fastenngs usng bolts, rawl plugs, etc. drectly to the shaft wall of the ar/flue gas system. > Do not attach fastenngs to prmary wallng or sdeways to the wall. > Observe the specfcatons provded by the manufacturer of the ar/flue gas system. 7. Shorten the flue ppe to the length requred and nsert the ar ppe Key A Ar B Flue gas > On the ar/flue gas system, establsh a connecton n accordance wth the dmensons n secton 3. These dmensons allow for the lateral nstallaton of the unt or nstallaton drectly on the prmary wallng. Ceramc ar/flue gas systems are usually equpped wth rubber sealng sleeves and have a ppe stop on the ar-sde connecton. > Separate the sleeve on the flue ppe so that you can slde the flue ppe nto the seal. > Insert the ar ppe nto the sleeve of the ar/flue gas system. > Insert the flue ppe nto the flue seal of the ar/flue gas system. When fttng further elements, prevent the flue ppe from sldng nto the flue gas duct. Metal ar/flue gas systems feature cylndrcal supports on the flue-gas-sde. In ths case, nsert the concentrc flue ppe wth sleeve. For ar/flue gas system shafts that have no sleeves, you must secure the ar ppe usng mortar and seal the shaft. > Ft the horzontal flue gas ppe ( secton 3). 8 Installaton manual for the flue ppe for ecotec plus _0

29 Installng the flue gas ppes n the shaft 8 8 Installng the flue gas ppes n the shaft Openng desgn 8. General nformaton for shaft openngs of flue gas ppes next to another flue gas nstallaton m Dh 8. Flue gas ppe n the shaft next to a flue gas nstallaton that does not have to be soot-proof Key Chmney extenson Flue gas The heght of the attachment depends on the dameter of the other flue gas nstallaton and must be desgned n accordance wth Fg. 8.. Attachments for rasng flue gas nstallatons are offered by varous chmney companes. If the other flue gas nstallaton cannot be rased, you must operate the unt as an open-flued system. Dh 8. Heght of the chmney above the flue gas ppe PP - room-sealed Key Chmney extenson Flue gas > Rase the chmney usng a soot-resstant extenson, so that the chmney projects above the PP flue gas ppe by at least m. b Cauton. Rsk of damage caused by soot n the neghbourng chmney. The openng of the flue gas ppe may become damaged by the effect of heat from the neghbourng chmney (chmneys are soot-resstant flue gas nstallatons sutable for sold fuel fres). > Desgn the openng accordng to one of the three optons below. Installaton manual for the flue ppe for ecotec plus _0 9

30 8 Installng the flue gas ppes n the shaft Openng desgn 8. Installng the rgd flue gas ppe Dh 8.. System dagram 7 9 0, m 6 8 Dh 8.3 Heght of the chmney above the PP flue gas ppe wth stanless-steel openng room-sealed > Establsh the openng of the flue gas ppe usng noncombustble parts up to 0. m below the shaft openng. > Rase the chmney as shown n Fg Openng desgn 3 0, m 8.5 System dagram of flue gas ppe n the shaft 8. Heght of the chmney above the PP flue gas ppe wth stanless steel openng open-flued > Establsh the openng of the flue gas ppe usng noncombustble parts up to 0. m below the shaft openng. > Operate the unt as an open-flued system. Key: Mountng ral Support elbow 3 Extenson Spacer 5 Cleanng T-pece 6 Black flue ppe 7 PP shaft cover 8 Stanless steel flue ppe 9 Stanless steel shaft cover 30 Installaton manual for the flue ppe for ecotec plus _0

31 Installng the flue gas ppes n the shaft Installng the flue gas ppe Installaton nstructons a Danger! Rsk of damage to the flue gas ppe due to soot burnng n the neghbourng chmney. The flue gas ppe can become damaged by the effect of heat from the neghbourng chmney (chmneys are soot-resstant flue gas nstallatons sutable for sold fuel fres). > Ensure that the clearance between the plastc nner ppe and the nsde of the shaft around the ppe s at least 5 mm, and around the sleeve s at least 5 mm. a Danger! Rsk of posonng due to escapng flue gas! Mneral-ol-based greases can damage the seals. > Use only the suppled lubrcant to facltate nstallaton. > Lghtly grease the seal and nsertng ends. 8.7 Correct postonng of seals (), ncorrect postonng of seals () > When nstallng the ppes, always ensure that the seals are postoned correctly: The lp of the seal must be facng nwards (). It must not be facng outwards (). > Deburr the ppes. 5mm Chamferng the ppes > Chamfer the ppes before they are nstalled to prevent damage to the seals. Mantan an angle of 5 and a clearance of 5 mm. > Remove all chppngs. > Do not nstall any dented or otherwse damaged ppes. Note that the ppes must be transported to the nstallaton ste only n the orgnal packagng. 8.6 Greasng the seal and the nsertng ends wth lubrcant > Do not use any damaged seals. At temperatures below 0 C, the ppes must be warmed before begnnng nstallaton. Installaton manual for the flue ppe for ecotec plus _0 3

32 8 Installng the flue gas ppes n the shaft Installng the and flue ppes The shaft dmensons for nstallng the basc set must be at least: Room-sealed: secton 5.: Maxmum permssble ppe lengths Open-flued: 50 mm x 50 mm (quadratc cross-secton) or Ø 70 mm for round shafts > Note the maxmum permssble ppe lengths of the flue gas gudng ( secton 5.). a Danger! Rsk of posonng due to flue gas ext! If the gradent s not suffcent, condensate remans n the sleeve whch damages the seals. Defects n the seals may result n flue gas ext. > Select the nstallaton ste n the shaft so that the flue ppe s at a downward gradent of 3 (3 corresponds to a downward gradent of approx. 50 mm per metre of ppe length) to the unt. 6 b Cauton. Rsk of damage to the structural ntegrty. Wth open-flued operaton, even n the case of low, permtted gas leakages, mosture may stll enter the shaft. The shaft must therefore be ventlated n order to dvert the flue gas leakages outsde. > Install an ar nlet openng at the lower end of the shaft (at least 0 cm openng cross-secton). > Enclose the openng usng the ntake grlle. > Determnng the nstallaton ste of the flue gas gudng n the shaft. > Drll a suffcently large openng to allow enough space for nstallaton. > Drll a hole (Ø 0 mm) n the rear sde of the shaft. > Insert the () wth the mountng ral () so that the flue ppe s postoned n the centre of the shaft. > For stablty, pont the openng of the U profle downwards. Mountng rals wth a length of 500 mm are also avalable. The can also be placed on a support ppe ( secton 8..6). Installng the flue gas ppe on a 5 > Slde the spacers () onto the flue gas gudng at a maxmum dstance of m, as shown n Fg Ft the and nsert the flue ppes n the shaft 8.0 Installng spacers > Secure a lne (6) to the lower end of the frst flue ppe (3) ( Fg. 8.9). > Use the lne (6) to lower the frst flue ppe (3) down far enough untl you can nsert the next flue element (5) ( Fg. 8.9). 3 Installaton manual for the flue ppe for ecotec plus _0

33 Installng the flue gas ppes n the shaft 8 Note that the sleeve-sde of the flue ppes must always pont upwards. Contnue jonng the flue ppes together untl you can nsert the lowest ppe nto the. > Insert the flue ppes nto the sleeve untl they reach a stop. > If the flue gas ppe cannot be nspected from the shaft openng, nstall an nspecton T-pece n a sutable poston. If dversons are requred n the shaft, > nstall a 5 or 30 elbow. After every dverson, you must nstall an nspecton T-pece as close as possble to the dverson Installng a shaft extenson 8.. Installng the PP shaft extenson mn. 300 mn b Cauton. Rsk of damage due to thermal expanson. Thermal expanson of the PP flue ppe can cause the openng of the flue gas ppe to ncrease by up to 0 cm. > Ensure that the necessary free space s avalable above the hood. b Cauton. Rsk of damage to the unt caused by flue gases or drt partcles. Flue gases or drt partcles that have been sucked n may damage the condensng unt or lead to malfunctons. If the openng of the flue gas ppe for the room sealed unt s mmedately next to another flue gas nstallaton, flue gases or drt partcles may be sucked n. > Lft the other flue gas nstallaton wth a sutable attachment. 8. Installng the PP shaft extenson The top flue ppe (3) must be resstant to solar radaton. > Install the black plastc flue ppe ncluded n the scope of delvery for the shaft connecton set. The black plastc ppe must project by at least 300 mm above the shaft sde and must protrude nto the shaft by at least 00 mm. > Remove the lne from the shaft. > Slde the shaft extenson () over the black plastc ppe (3). > Secure the shaft extenson to the shaft sde usng rawl plugs and bolts. > Durng ths process, secure the top cover wth rear ventlaton () to the shaft extenson (). Installaton manual for the flue ppe for ecotec plus _0 33

34 8 Installng the flue gas ppes n the shaft 8..5 Installng the stanless steel PP shaft extenson 8..6 Installng the flue gas ppe on a support ppe The flue gas ppe n the shaft can also be nstalled on a support ppe nstead of a mountng ral. mn mn Installng a support ppe > Saw through the flue gas ppe () at the markng (). > Turn the sawn-off sleeve (3) around and slde t back onto the flue ppe. 8. Installng a shaft extenson The top flue ppe (3) must be resstant to solar radaton. > Install the stanless steel flue ppe. The stanless steel flue ppe must project by at least 300 mm above the shaft sde and must protrude nto the shaft by at least 00 mm. > Remove the lne from the shaft. > Seal the edge of the openng wth slcone. > Slde the shaft extenson () over the stanless steel flue ppe (3). > Secure the shaft extenson to the shaft sde usng rawl plugs and bolts. > Durng ths process, secure the top cover wth rear ventlaton () to a fxng screw usng the safety lne ncluded. > Ensure that the top cover () s secured to the shaft extenson () usng the wng nut (6) Installng the support ppe n the shaft > Adjust the length of the support ppe between the shaft floor and the. > Install the spacer (5) on the support ppe. > Place the support ppe () wth the sawn-off sleeve facng upwards, on the base of the shaft. > Place the (6) onto the support ppe (). 3 Installaton manual for the flue ppe for ecotec plus _0