WATER SYSTEMS. Lancer Carbonators and Components. Part Number Description. SHURflo High Pressure Electric Carbonator

Transcription

1 1. Carbonators and Accessories 2. Water Boosters and Accessories 3. Water Filtration Systems and Replacement Filters 4. Water Bottle Dispensing System Lancer Carbonators and Components Known for its superior quality and reliability, the Turbo heavy duty, high capacity carbonator has a 100 GPH (379 LPH) pump, ideal for fast flow valves. With 60 F inlet water it will provide a carbonation level of 6.0. With 75 F inlet water it will provide a carbonation level of 5.5, and at maximum flow 5.3. Turbo has solid state electronics, a built-in advanced diagnostics system, ASSE approved vented check valve, stainless steel base with rubber feet, 3/8" male barb inlets and dual 3/8" male flare soda outlets. Dimensions: 12.25"W x 12.5" H x 14.25" D. Shipping weight: 35 lbs. Number Description Carbonator, fast flow with vented check valve (VCV) Carbonator, recirculating system /01 Probe assembly, fast flow, Turbo Probe assembly, universal Liquid level control board, universal Proximity switch assembly /01 Carbonation tester kit Lancer Turbo carbonator / /01 SHURflo High Pressure Electric Carbonator 8005 Series, positive displacement, open flow, 3 chamber diaphragm pump is self-priming and can run dry without damage. Comes with ground wires and base plate. Flow rate: 1.4 GPM. Operating pressure: 100 psi. 115V. Number Description Carbonator, high pressure, 100 psi, 1.4 GPM Continuing product improvements may necessitate E-1

2 McCann s Carbonators and Components McCann s carbonators produce 100 GPM, have Diamond Bright tanks, brass water pumps, and encapsulated electronics to prevent moisture damage. Base is injection molded with press-in rubber feet to reduce noise. Heat sink probe caps prolong probe life, 2-piece probe design simplifies diagnostics, and there s no need to shut off the water or CO 2 for service. To test the 2-piece float probe: remove the probe electronics, pass the tip of a magnetic screwdriver past the lower end of the tube. If the reed switch closes, it is operating properly. The 2-piece probe has a five year warranty. Recirculating cold carb system maintains temperature at F for optimum carbonation levels, and can be easily retrofit any installed dispenser system. E All carbonators are 1/3 HP, 7.0 amps, 115/60/1, have ASSE 1022 backflow preventors, vented check valves, 1/4" MF CO 2 inlet, 3/8" MF water inlet and 3/8" MF soda water outlet(s). Number Low Lead Description E E Big Mac carbonator 13.5" W x 10.5" H x 12.75" D Standard carbonator 9" W x 11" H x 11.5" D Carbonator-in-a-box 12.25" W x 15" H x 6.5" D LL Recirculating cold carb system 25" W x 15" H x 18" D Tank 2 gals oz oz. 1 2 gals. 2 Soda Outlets McCann s Carbonator Components Number Description Float and probe assembly Probe kit and mounting studs Probe only male prong to 3 female prong adaptor cord/plug female prong cord/plug Power cord assembly (18/3), 8' Carb pump saver with lamp Pressure relief valve for carb tank, 180 psi Check valve, single, 1/4" MFL Check valve, double, 1/4" MFL E recirculating cold carb system Carbonator foot (for bases) E-2 Continuing product improvements may necessitate

3 McCann s Carbonator Components Continued Number Description E Water inlet & nut assembly, plastic base Water inlet tubing assembly, 3/8", ASSE Carbonator tank assembly, large w probe, 2 out Carbonator tank assembly w decals, large, 2 out Carbonator tank assembly, weld complete, 2 out Carbonator tank, small, 3/8 out, w decals & stud Back Flow Preventors A vented backflow preventor will provide pressure relief if the primary check valve fails, ensuring that the secondary check valve will remain closed. Plumbing codes in most states require that a ASSE standard 1022 vented backflow preventer is used on all carbonated beverage dispensers. Those with an internal ASSE 1032 non-vented check valve must have an ASSE 1022 check valve installed on the dispenser water line DS470DVV66X DS470DVV6F6X DS Number Type Description Fitting ASSE 1022 ABF-1 brass check valve, low lead ASSE 1022 ABF-1 brass check valve w 1/8" vent, low lead ASSE 1022 Watts SD-3 check valve 3/8" MF ASSE 1022 Watts SD-3 check valve with strainer 3/8" MF ASSE 1022 Watts SD-2 double check valve 3/8" MF S2722 ASSE 1022 Vent tube fitting 1/8" barb ASSE 1022 McCann s E3000 conversion kit ASSE 1022 McCann s E2000 conversion kit ASSE 1022 McCann s 43 Series conversion kit S470DVV66X ASSE 1032 Double check with vent 3/8" MF S470DVVP66X ASSE 1032 Double check with vent 3/8" MPT x 3/8" MF S470DVV6F6X ASSE 1032 Double check with vent stem 3/8" MF x 3/8" FF S470D66 SS Ball Double ball check valve 3/8" MF S470DH4H4 SS Ball Double ball check valve 1/4" barb S470DFP4P4 SS Ball Double ball check valve 1/4" FNPT x 1/4" NPT S47066 SS Ball Single ball check valve 3/8" MF S470H6H6 SS Ball Single ball check valve 3/8" barb Continuing product improvements may necessitate E-3

4 Carbonator Pumps Rotary vane pumps move potable water to beverage dispensers. Models with strainers have removable caps for periodic cleaning (every four months under normal conditions). Inlet and outlet ports are 3/8" NPT threaded. Some states require low or lead-free metals. The products listed below are the most commonly ordered part numbers. For additional pump options call ABS customer service. Fluid-O-Tech PA350X Fluid-O-Tech PA350 Fluid-O-Tech PA310X Fluid-O-Tech PA801 Number Procon Series 1 Procon Series 2 Procon Series 3 Procon Series 4 Low Lead Number Series Brass or SS GPH PSI Strainer Bypass Adj./ Releif Valve Brand PA350X250 PB350X250 PA Brass Yes Yes Fluid-O-Tech 111A100F11AA A100F11AA250LL 1 Brass Yes Yes Procon 111A125F11AA A125F11AA250LL 1 Brass Yes Yes Procon PA PB PA Brass No Yes Fluid-O-Tech 112A100F11AA A100F11AA170LL 2 Brass No Yes Procon 112A050F11AB A050F11AB100LL 2 Brass No Yes Procon 112E100F11BA E100F11BA170LL 2 Brass No Yes Procon PA PB PA Stainless Steel No No Fluid-O-Tech PA PB PA Stainless Steel No No Fluid-O-Tech 113A025F31XX 113A025F31XXLL 3 Stainless Steel 25 N/A No No Procon PA PB PA Stainless Steel No Yes Fluid-O-Tech PA PB PA Stainless Steel No Yes Fluid-O-Tech 113A050F31AB 113A050F31ABLL 3 Stainless Steel No Yes Procon 113A100F31AA 113A100F31AALL 3 Stainless Steel No Yes Procon 113A100F31AAT 113A100F31AATLL 3 Stainless Steel No Yes Procon PA PB PA Brass Yes Yes Fluid-O-Tech 114B240F11BA 114B240F11BALL 4 Brass No Yes Procon E-4 Continuing product improvements may necessitate

5 Carbonation Testers Proper carbonation is critical to soft drink quality. During preventive maintenance several soft drink samples are poured into the chilled tester. Pressure and temperature are recorded and cross-referenced with the table on the canister to determine the current carbonation volume, and whether or not the carbonation needs adjustment. Pepsi carbonation tester Carbonator s and Accessories CM1FJ CM3FJ Lancer carbonation tester A 263A Number Description 2701 Pepsi carbonation tester, complete assembly A Pepsi carbonation tester, thermometer assembly 27013A Pepsi carbonation tester, relief valve assembly A Pepsi carbonation tester, canister assembly 2701A10 Pepsi carbonation tester, cap (must be purchased with gasket) Pepsi carbonation tester, gasket with adhesive, for cap Pepsi carbonation tester, gauge 0-30 psi 600GP Pepsi carbonation tester, gauge protection boot /01 Lancer carbonation tester, complete assembly Lancer carbonation tester, thermometer assembly Lancer carbonation tester, vent valve stem Lancer carbonation tester, vent cap Lancer carbonation tester, housing Lancer carbonation tester, adapter Lancer carbonation tester, seal /02 Lancer carbonation tester, cap Lancer carbonation tester, gauge /3 HP carbonator motor, welded base, 115V /3 HP GE carbonator motor, 115/230V (dual) /3 HP carbonator motor, welded base, 8 ft. harness, 115V /3 HP carbonator motor, resilient base, 8 ft. harness, 115V /3 HP carbonator motor, H682, carb ball bearing 1138 Strainer screen for Series 1 Procon pump 1143 Coupling ring for Procon pump Pressure spring G Insulation cover for Series 3 Procon pump W Insulation cover right side for Series 1 Procon pump Insulation cover left side for Series 1 Procon pump Carbonator/water booster floor stand, stainless Carbonator/water booster wall or rack mount shelf, stainless CM1FJ Carbonator/water booster floor stand, black CM3FJ Carbonator/water booster wall or rack mount shelf, black A Watts water regulator, 3-50 psi, no gauge port, 3/8" FNPT A Watts water regulator, psi, no gauge port, 3/8" FNPT A Watts water regulator, psi, 1/4" MPT gauge port, 3/8" FNPT gallon accumulator tank Continuing product improvements may necessitate E-5

6 Water Booster Systems Water boosters provide consistent water pressure to beverage dispensing systems, ensuring optimum performance. Gas-Driven Boosters Flojet K56 system has a 1/2 gallon accumulator tank, quick disconnect ports, and exhuast muffler for quiet operation. It is self-priming, supplies up to 4 GPM, and operates psi. Dimensions: 12" H x 11.5" W x 7" D. 1 year warranty. Flojet G56 pump operates quietly and supplies up to 4 GPM. If pumping over 1.7 GPM a pulsation dampener or accumulator tank should be used to reduce pulsation due to momentary shifts in flow requirements. Operates psi. Dimensions: 5.27" H x 3.21" W x 4.58" D. Weight: 1.24 lbs. 1 year warranty. G56 pump K56 system Number Description Product Inlet Product Outlet Gas Inlet K561030A K56 water boost system w 1/2 gal tank 1/2" barbed straight plastic 1/2" barbed straight nylon 1/4" CO 2 shutoff brass G561215A G56 water pump, stand-alone or 1/2" barbed straight plastic 1/2" barbed straight plastic 1/4" CO 2 shutoff brass replacement pump for K56 system G56 pump muffler port N/A N/A N/A K56 1/2 gallon bladder tank N/A N/A N/A Fully Automatic Electric Boosters Typically used when pumping from a cistern, water storage tank, or other ground water source. Both 2820 and 2840 Series have an accumulator tank, built-in inlet strainers, pressure switches and check valves. Dimensions: 11" W x 7" H x 11.5" D. 115V. 1 year warranty and 2840 system Number Description Product Inlet/Outlet PSI GPM A 2820 Series, 115V 3/8" FPT A 2840 Series, 115V 1/2" OD or 3/4" OD hose barb A 2840 Series, 115V 1/2" OD or 3/4" OD hose barb A 2840 Series, 24V 1/2" OD or 3/4" OD hose barb E-6 Continuing product improvements may necessitate

7 Triplex Water Booster System Triplex has a 4 gallon stainless steel tank, provides 1.4 GPM, and up to 100 psi outlet. Its advanced pump technology provides high efficiency, increased drawdown time, and extended life. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. Operating temperature: F. Pump inlet: 3/8" hose barb. Tank discharge port: 1/2" hose barb. 115V. Triplex Water Booster/Water Delivery Pumps The Triplex High Pressure diaphragm pumps are self-priming and can run dry without harm. They are intended for intermittent duty cycles but can be run continuously for short periods of time. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty. Duplex II Water Booster/Water Delivery Pumps The self-priming Duplex II Series with new diaphragm design, new valves, built-in back flow preventer, heavy-duty ball bearings and motor have been designed for maximum efficiency and long life. 115V. AC Variable Speed Drive (VCD) Pumps The AC VCD constant pressure pump matches motor speed to system demand to provide stable flow and reduced amp draw, eliminating unwanted pump switch cycling and the need for an accumulator tank. If the inlet pressure exceeds 30 psi the pump requires a 30 psi water regulator. 115V. 1 year warranty. Number Description Water Inlet Water Outlet PSI GPM A Triplex booster system 3/8" barb 1/2" barb A Triplex Series 3/8" FPT 3/8" FPT A Triplex Series 3/8" FPT 3/8" FPT D4821H4011A Duplex II Series 3/8" FPT 3/8" FPT D4831H5011A Duplex II Series 3/8" FPT 3/8" FPT D4834H6011A Duplex II Series 3/8" FPT 3/8" FPT D4834H7011A Duplex II Series 3/8" FPT 3/8" FPT A AC VCD with 3 wires A AC VCD cable with plug 5.0 Continuing product improvements may necessitate E-7

8 Flojet Water Booster Accessories Number Description C Inline water regulator, 50 psi, QD connect, no ports C Inline water regulator, 50 psi, QD connect, 3/8" hose barb ports C Inline water regulator, 30 psi, QD connect, no ports C Inline water regulator, 30 psi, QD connect 3/8" hose barb ports Accumulator tank, 1 gallon, 3/4" MPT openings, no fittings A Accumulator tank,.60 gallon, 3/4" MPT openings, no fittings Accumulator tank, 125 psi,1 quart/liter capacity, 1/2" barb fittings B Accumulator tank, rubber valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings B Accumulator tank, metal valve, 125 psi, 1/2 quart/liter capacity, 1/2" barb fittings / A Flojet Water Booster/Pump Fittings Inline water regulators B/ B A A B B Number Application Pump Series Barb Size Shape Material Additional Info A Inlet/Outlet G56 & K56 1/4" Straight hose barb Stainless steel A Inlet/Outlet G56 & K56 3/8" Straight hose barb Stainless steel Inlet/Outlet G56 & K56 1/2" Straight hose barb Plastic/Celcon Inlet/Outlet G56 & K56 1/2"-3/8" Straight hose barb Plastic/Celcon Inlet/Outlet G56 & K56 1/2" Elbow hose barb Plastic/Celcon Inlet/Outlet G56 & K56 1/2"-3/8" Elbow hose barb Plastic/Celcon B Inlet/Outlet G56 & K56 1/4" Straight Plastic John Guest B Inlet/Outlet G56 & K56 3/8" Straight Plastic John Guest B Inlet/Outlet G56 & K56 1/2" Straight Plastic John Guest Inlet/Outlet Duplex II & /8" x 3/8" Straight, MPT x barb Plastic Inlet/Outlet Duplex II & /4" x 3/8" Straight, MPT x barb Plastic Inlet/Outlet Duplex II & /8" x 1/2" Straight, MPT x barb Plastic Inlet/Outlet Duplex II & /8" x 1/4" Straight, MPT x barb Plastic Inlet/Outlet Duplex II & /4" x 1/4" Straight, MPT x barb Plastic Inlet/Outlet Duplex II & /8" x 3/8" Elbow, MPT x barb Plastic Inlet/Outlet Duplex II & /4" x 3/8" Elbow, MPT x barb Plastic Inlet/Outlet Duplex II & /8" x 1/2" Elbow, MPT x barb Plastic Inlet/Outlet Duplex II & /8" x 1/4" Elbow, MPT x barb Plastic Inlet/Outlet Duplex II & /4" x 1/4" Elbow, MPT x barb Plastic E-8 Continuing product improvements may necessitate

9 McCann s Water Boosters McCann s electric water boosters have stainless steel tanks and fittings, pre-charged bladders and relief valves. Flow rates up to 100 GPH. Minimum inlet pressure: 20 psi. Outlet pressure switch: psi. 115V. Standard water boosters have a 1/3 HP motor, 100 GPH brass rotary vane pump and single ball check valve. Economy water boosters have a 100 GPH Aquatec motor and pump combination. Standard model Number Model Tank Inlet/Outlet Additional Information Standard 4 gallon 3/8" / 1/2" Standard 4 gallon 3/8" / 1/2" Low lead brass Standard 4 gallon 3/8" / 1/2" CC Standard 4 gallon 3/8" / 1/2" Low lead brass, CC Standard 2 gallon 3/8" / 1/2" Standard 2 gallon 3/8" / 1/2" Low lead brass Standard 2 gallon 3/8" / 1/2" CC Standard 2 gallon 3/8" / 1/2" Low lead brass, CC /8 Economy 2 gallon 3/8" /2 Economy 2 gallon 1/2" /8 Economy 4 gallon 3/8" /2 Economy 4 gallon 1/2" Economy model McCann s Water Booster s and Accessories Number Description Pressure switch and cord assembly for all McCann s boosters 111A100F11AA250 Rotary vane pump for or Motor for or Aquatec motor for , or Continuing product improvements may necessitate E-9

10 SHURflo Electric Water Booster Systems All booster systems include a mountable base, 30 psi water regulator and pump cord. The Mini has a plastic accumulator tank. The Medium and Maxi booster systems have a stainless steel tank. 115V. Mini Medium Maxi Number Description GPM Tank PSI Water Inlet/Outlet Mini boost system w mounting board 21 oz. 60 psi 3/8" metal barb Mini boost system w mounting board 21 oz. 90 psi 3/8" metal barb Medium E boost system w side mount, quick disconnect pump ports, gal 90 psi 3/8" metal barb replaceable tank bladder SV Medium E boost system w side mount, quick disconnect pump ports, gal 90 psi 3/8" metal barb replaceable tank bladder, SHURlock shut-off ball valve Maxi boost system, 3/8" inlet/outlet gal 90 psi 3/8" metal barb Maxi boost system, 1/2" inlet/outlet gal 90 psi 1/2" metal barb SHURflo Electric Water Pumps Positive displacement 3 chamber diaphragm water delivery pumps are self-priming, and can run dry without damage. Pumps include ground wires and baseplate. 115V Series 2088 Series 8005 Series Number Description GPM PSI Water Inlet/Outlet Transfer pump /2" MPT Delivery pump /2" MPT Standard water boost pump /8" FPT Standard water boost pump /8" FPT Replacement pump for water boosters: , , High flow/high pressure water boost/carbonation pump with two 3 chamber diaphragms /8" barb SHURflo Accumulator Tanks Number Description Water Inlet/Outlet oz. accumulator tank, metal mounting bracket 1/2" FPT oz. accumulator tank, gas pump QD clip ports gallon stainless steel tank, 1/2" or 3/4" FPT E-10 Continuing product improvements may necessitate

11 Water Booster Filter Combo Systems Filtered water improves the flavor of soft drinks, increases carbonation, and extends the life of equipment. Boosted water ensures consistent water pressure for consistent brix ratio, maximum flow rate and efficiency. Combining the two systems into one conserves valuable space. SHURflo s LVPO (Low Volume per Outlet) water boost filtration system is a complete turn-key solution which provides perfect ingredient water to low volume fountain dispensers and ice machines. The LVPO filtration system features: SHURflo 90 psi, 115 VAC, 8000 Series corded booster pump 2 gallon stainless steel water accumulator tank LVPO F-1 Big Boy 5 micron carbon block inline filter for particulate, chlorine, taste and odor reduction Filter can be mounted in any orientation, improving serviceability Colored coded inlet & outlet filter ports & valves for easy identification of water flow Quick connect 3/8" barb inlet/outlet ports Low pressure drop (less than 8 psi at 3.0 gpm) 50 psi pre-charge recommended for most beverage applications WB2LVPO01 is designed for single fountain dispensers that serve less than 500 gals. of syrup per year. Service life of filter: 6, GPM. SHURlock Fittings Double O-ring QD ball valve fittings (1/2" FPT straight & elbow available) 3/8" barb WB2LVPO02 has two filters; one that pressurizes and filters the water to a single dispenser that serves less than 500 gals. of syrup per year, and one that provides nonboosted treated water to the ice-maker. LVPO-F-1 (fountain filter) reduces particulates, chlorine, bad taste and odors. Service life: 6, GPM. LVPO-F-2 (ice filter) reduces particulates and inhibits lime scale build-up. Service life depends on the water conditions. Number WB2LVPO01 WB2LVPO02 Description Water boost/filter combo system for fountain dispenser, single filter cartridge Water boost/filter combo system for fountain dispenser and ice machine, dual filter cartridges SHURlock kit: 1/2" FPT quick connect swivel ball valve, (2) 3/8" barb x 1/2" MPT Continuing product improvements may necessitate E-11

12 Selecto Water Booster Filter Combo Systems Selecto SMF filters remove 99% of all contaminants, don t require a pre-filter for sediment removal, and provide high flow rates (up to 100 GPH/1.7 GPM) with nearly zero pressure drop. NSF std. 42 & 53. All SMF filters remove chloramine (chlorine + 20% ammonia used in many municipalities to slow the dissipation of chlorine). Chloramine has a strong odor, deteriorates O-rings, and causes stainless steel to pit, rust and turn gray. Low draw systems have a 2 gallon tank, high draw systems have a 4 gallon tank. Filters with -5 in the description have ScaleOUT (scale inhibitor) for ice machines. Operating pressure: psi. Operating temperature: F. Inlet and outlets: 3/8" barbs. Water analysis, site survey, selection of water appliances, service, maintenance and training are available. QC350 Low Draw QC500 Low Draw QC500/ScaleOUT Low Draw SMF IC600 Low Draw SMF IC600-5 Low Draw SMF IC614-5 Low Draw SMF IC620 Low Draw SMF IC620-5 Low Draw SMF IC620-5 High Draw Number Description Chlorine Chloramine Scale Tank Replacement Cartridge(s) QC350 Low Draw 8,000 gals. 4,000 gals. N/A 2 gals. QC QC500 Low Draw 11,000 gals. 6,000 gals. N/A 2 gals. QC S QC500/ScaleOUT Low Draw 11,000 gals. 6,000 gals. 30,000 gals. 2 gals S LFM SMF IC600 Low Draw 50,000 gals. 7,000 gals. N/A 2 gals LFM SMF IC600-5 Low Draw 50,000 gals. 7,000 gals. 75,000 gals. 2 gals S LFM SMF IC614-5 Low Draw 70,000 gals. 15,000 gals. 75,000 gals. 2 gals S LFM SMF IC620 Low Draw 100,000 gals. 30,000 gals. N/A 2 gals LFM SMF IC620-5 Low Draw 100,000 gals. 30,000 gals. 75,000 gals. 2 gals S HFM SMF IC620-5 High Draw 100,000 gals. 30,000 gals. 75,000 gals. 4 gals S E-12 Continuing product improvements may necessitate

13 3M Water Filtration Products for Multi-Equipment Applications The High Flow Series can meet the filtration needs of an entire foodservice establishment or address specific applications one at a time. A one-cartridge High Flow system with Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media delivers recipe quality water of up to 5 gallons per minute, lasts 6 months, and accomplishes what was previously the job of a three- or four-cartridge system. The High Flow Series provides unprecedented cyst and bacteria reduction, sediment holding, chlorine taste and odor reduction and scale inhibition. Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media provides nearly 6 times the filtration surface area, and reduction of up to 99.99% of common water-borne heterotrophic bacteria as tested by 3M Purification Inc., as well as Cryptosporidium and Giardia cysts. No activation steps are required, and for most water, no pre-filter is needed. Change-outs are fast and easy with the Sanitary Quick Change (SQC) encapsulated cartridge design. Most cartridge materials are NSF Std. 42 and/or CRF-21 compliant and certified by NSF to Std. 53 for cyst reduction. Dual Port (DP) and Dual Flow (DF) Systems for Multiple Applications Two separate streams exit the manifold. Both streams have reduced sediment and chlorine taste and odor. One stream has added scale inhibition media from a dedicated cartridge to help reduce the ability of calcium and magnesium to adhere as hard scale on the evaporator plates of an ice machine and/or the heating coils of a coffee brewer. The second stream supplies cold beverage dispensers and includes no added scale inhibitor. DP190 DP290 DP390 Model Number Gallon GPM Flow Rate Micron Rating Fountain/Cold Cup Coffee/Tea/Hot Cup Espresso/Cappacino Ice Machine Case Qty. Replacement Cartridge Reduces DP , X X X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DP , X X X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DP , X X X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 DF290-CL* , /5.2 X X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chloramine, chlorine taste & odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Beverage flow rate is 2.66 GPM, ice machine flow rate is 5 GPM. Continuing product improvements may necessitate E-13

14 3M Water Filtration Products for Cold Beverages Cold beverages are often the most profitable part of convenience stores, restaurants and quick-service operations. For these high-volume cold beverage applications, High Flow filters deliver enough Recipe Quality Water to make more than 432,000 soft drinks (16 oz. soft drinks in 22 oz. cups) with a single cartridge. High Flow catridge filters deliver the improved performance of Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media. A single High Flow cartridge system replaces a three- or four-cartridge manifold system, lowering capital and operating costs. All systems on this page deliver sediment and chlorine taste and odor reduction. BEV130 (std. 42 & 53) and BEV135 (std. 42) contain media wrapped carbon-block only. BEV140, BEV160 and BEV190 systems include Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria 2 reduction, and are NSF std. 42 and 53. BEV135, BEV145, BEV165 and BEV195 systems are designed for high turbidity water, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials. BEV130 BEV135 BEV160 BEV165 BEV190 BEV195 Number Gallon GPM Flow Rate Micron Rating Fountain/Cold Cup Model Reduces BEV , X Cyst 1, sediment 3, chlorine taste & odor BEV , X Sediment 3, chlorine taste & odor Case Qty. Replacement Cartridge BEV , X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV , X Sediment 3, chlorine taste & odor BEV , X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV , X Sediment 3, chlorine taste & odor BEV , X Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor BEV , X Sediment 3, chlorine taste & odor 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory E-14 Continuing product improvements may necessitate

15 3M Water Filtration Products for Ice Machines Scale build-up on evaporator plates can significantly increase maintenance costs. 3M Water Filtration Products for ice machines provide built-in scale inhibition as well as chlorine and sediment reduction, which reduce service calls and downtime, yield consistent product, and increase customer satisfaction. ICE120-S (std. 42 & 53) and ICE125-S (std. 42) contain carbonblock media only. ICE140-S, ICE160-S, ICE190-S and ICE260-S include Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria 2 reduction, and are NSF std. 42 and 53. For higher turbidity waters, the media in ICE145-S, ICE165-S, ICE195-S and ICE265-S systems are specifically designed to provide cartridge and system life, but not cyst or bacteria reduction, and are std. 42 only. All have NSF and/or FDA CFR-21 compliant materials. ICE265-S ICE190-S ICE120-S ICE140-S Model Number Gallon GPM Flow Rate Micron Rating HF Cubers Lbs. To LF Cubers Lbs. To Flakers Lbs. To Continuing product improvements may necessitate E-15 Case Qty. Replacement Cartridges ICE120-S , HF20S ICE125-S , HF25S ICE140-S , HF40S ICE145-S , HF45S ICE160-S , HF60S ICE165-S , HF65S ICE190-S , >1000 >1450 > HF90S ICE195-S , >1000 >1450 > HF95S ICE260-S , (2) HF60S ICE265-S , (2) HF65S Reduces Cyst 1, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 Cyst 1, bacteria 2, bacteriostatic, sediment 3, chlorine taste & odor, scale 3 Sediment 3, chlorine taste & odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory

16 3M Water Filtration Products for Hot Beverages High Flow Series products for hot beverage applications reduce excess sediment and chlorine that cause bitter taste and clog spray heads. If not filtered, these elements can wreak havoc on your equipment and lead to expensive repair and replacement costs. When scale is an issue, High Flow BREW systems add scale inhibitor to prevent calcium and magnesium build-up that can significantly decrease efficiency and increase maintenance costs. ESP and ScaleGARD Pro (SGP) systems reduce calcium and magnesium ions by ion exchange (water softening) for crystal clear iced tea and excellent bean extraction for espresso and espresso-based beverages. ESP and SGP systems do not need a drain, electrical connection or salt regeneration. All have NSF and/or FDA CFR-21 compliant materials. BREW 120 BREW 130 ESP 124 SGP 165 Model Number Gallon GPM Flow Rate Micron Rating Coffee/Hot Cup Espresso/Capp./Tea Case Qty. Replacement Cartridge(s) BREW105-MS , X 8 HF05MS BREW110-MS , X 8 HF10MS BREW115-MS , X 8 HF15MS BREW120-MS , X 6 HF20MS BREW125-MS , X 6 HF25MS BREW130-MS , X 4 HF30MS BREW135-MS , X 4 HF35MS Reduces Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 Cyst 1, sediment 2, chlorine taste & odor, scale 2 Sediment 2, chlorine taste & odor, scale 2 ESP114-T* gr..5 N/A X Hardness (softens), chlorine taste & odor ESP124-T* ,100 gr..5 N/A X Hardness (softens), chlorine taste & odor SGP124BN-T* N/A X Hard scale 2, chlorine taste & odor SGP165BN-T* N/A X Hard scale 2, chlorine taste & odor SGP195BN-T* N/A X Hard scale 2, chlorine taste & odor SGP-124B* N/A X X Hard scale 2, chlorine taste & odor 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed E-16 Continuing product improvements may necessitate

17 3M Water Filtration Products for Hot Beverages - Reverse Osmosis NEW! For optimum flavor it is recommended that filtered water contain ppm of Total Dissolved Solids (TDS) for coffee and about 50 ppm for espresso. Designed for water conditions with high TDS and/or hardness, the TFS450 reverse osmosis (RO) water filtration system is ideal. RO is the tightest of all filtration processes, removing about 90% of all contaminants and providing the greatest equipment protection. The TFS450 has a blending feature that allows you to blend back just the right amount of TDS (from 10-50% of incoming feed water) into the water to satisfy both needs; equipment protection and customer satisfaction. With conventional RO systems the waste water can be 2-4 times the volume of the filtered water. For the production of 100 gallons of filtered water the TFS450 conserves up to 250 gallons of water per day - over 90,000 gallons per year - than conventional RO systems. Features: Makes 300 gal/day without blending*, and up to 600 gal/ day of blended water Blending valve (with lock) adjusts the desired amount of TDS, and online meter monitors product water TDS level Keeps running during high demand periods and power outages with automatic non-electric bypass All product water (including bypass) is pre- and postfiltered Change-outs are fast and easy with Sanitary Quick Change (SQC) disposable cartridges Compact, uses very little space, and is easy to install Optional pumping module is available for low inlet water pressure areas The TFS450 requires an external storage tank. TFS450 Model Number Gallon TFS450RO gpd without blending/ 600 gpd with blending Micron Rating Coffee/Hot Cup Espresso/Capp./Tea Case Qty. Replacement Cartridge(s) Reduces.0005 X X Cysts 1, sediment 2, chlorine taste & odor, TDS 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested and verified by Manufacturer s Laboratory *at 77 F and 70 psi. Continuing product improvements may necessitate E-17

18 3M Replacement Cartridges for 3M Water Filtration Systems Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces HF05-MS 1, Sediment 3, chlorine taste and odor, scale HF10-MS 3, Cyst 1, sediment 3, chlorine taste and odor, scale HF15-MS 3, Sediment 3, chlorine taste and odor, scale P124BN* 423@ 10 gr..5 N/A 4 Hardness, chlorine taste and odor PS124* 1,100 gr..5 N/A 4 Hardness, chlorine taste and odor PS114* 700 gr..5 N/A 6 Hardness (softens), chlorine taste and odor HF40 25, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor HF40-S 25, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale HF45 25, Sediment 3, chlorine taste and odor HF45-S 25, Sediment 3, chlorine taste and odor, scale HF60 35, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor (2) HF60-S 70, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale HF65 35, Sediment 3, chlorine taste and odor (2) HF65-S 70, Sediment 3, chlorine, taste and odor, scale HF90 54, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor HF90-S 54, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale HF95 54, Sediment 3, chlorine taste and odor HF95-S 54, Sediment 3, chlorine taste and odor, scale DP190-CARTPAK 54, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale DP290-CARTPAK 108, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale DP390-CARTPAK 162, Cyst 1, bacteria 2, sediment 3, chlorine taste and odor, scale DF290CL-CART- 25, /5.2 1 Cyst 1, bacteria 2, sediment 3, chloramine, chlorine taste and odor, scale 3 PAK P195BN* 1200@ 9 gr. 1 N/A 1 Hardness, chlorine taste and odor HF20-S 9, Cyst 1, sediment 3, chlorine taste and odor, scale HF30 14, Cyst 1, sediment 3, chlorine taste and odor HF20-MS 9, Cyst 1, sediment 3, chlorine taste and odor, scale HF30-MS 14, Cyst 1, sediment 3, chlorine taste and odor, scale HF25-S 10, Sediment 3, chlorine taste and odor, scale 3 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed E-18 Continuing product improvements may necessitate

19 3M Replacement Cartridges for 3M Water Filtration Systems Sorted by Number Number Gallon GPM Flow Rate Model Reduces HF35 12, Sediment 3, chlorine taste and odor HF25-MS 10, Sediment 3, chlorine taste and odor, scale HF35-MS 12, Sediment 3, chlorine taste and odor, scale P165BN* 719@ 9 gpg 1 N/A 1 Hardness, chlorine taste and odor CFS9110 N/A Sediment CFS , Sediment 3, chlorine taste and odor CFS9812X 9, Cyst 1, sediment 3, chlorine taste and odor CFS9720 4, Sediment 3, chlorine taste and odor CFS9110S N/A Sediment 3, scale CFS9112S 10, Sediment 3, chlorine taste and odor, scale CFS9812XS 9, Cyst 1, sediment 3, chlorine taste and odor, scale CFS9710S 2, Sediment 3, scale CFS9720S 4, Sediment 3, chlorine taste and odor, scale CFS9005IMF N/A N/A N/A 12 Scale CFS9112EL 12, Sediment 3, chlorine taste and odor CFS9812ELX 14, Cyst 1, sediment 3, chlorine taste and odor CFS9720EL 5, Sediment 3, chlorine taste and odor CFS9112ELS 12, Sediment 3, chlorine taste and odor, scale CFS9812ELXS 14, Cyst 1, sediment 3, chlorine taste and odor, scale CFS9720ELS 5, Sediment 3, chlorine taste and odor, scale * SWC9135 1,350 gr..5 N/A 4 Scale 3 (softens water) * SWC9135C 1,100 gr Chlorine taste and odor, scale 3 (softens water) Micron Rating 1 Contains Integrated Membrane Pre-Activated Carbon Technology ( IMPACT ) media for cyst and bacteria reduction. Tested by manufacturer. 2 As tested with E. Coli ATCC (11229) by 3M Purification Inc. Not tested or certified by NSF International. 3 As tested and verified by Manufacturer s Laboratory *Systems not NSF listed Case Qty. 3M Replacement Filters NEW! NEW 9000 Series cartridges fit all Everpure heads, both old and new style. Continuing product improvements may necessitate E-19

20 Selecto Water Filtration Systems Selecto s SMF filters last up to 10 times longer than traditional carbon filters. Modular units are simple to install and service, and adaptable to changing water conditions change. All systems (except some inline filters) come with mounting brackets. Fountain systems have a pressure gauge. 100% performance guarantee. NSF 42 & 53. Selecto s hollow carbon filter Traditional carbon block filter Selecto can customize a filtration system to meet your requirements. Call customer service for details. IL35 QC350 QC500 SMF IC600 SMF IC614 SMF IC620 SMF IC620S SMF IC6142 SMF IC6202 SMF IC6203 SMF Espresso 7500 SMF Espresso SMF CoffeePRO SMF IC600S ScaleOUT-W E-20 Continuing product improvements may necessitate

21 Selecto Water Filtration Systems Gallon GPM Flow Rate Fountain Juice Coffee Tea* Espresso/Capp. Ice Machine Replacement Cartridge(s) Model Number Reduces/Eliminates IL /35 3,000 2 X X X X 0110/35 Chlorine, sediment, bad taste, odor IL35B 0110/35B 3,000 1 X X X 0199/35B Chlorine, sediment, bad taste, odor IL35S 0110/35S 3,000 2 X X X 0110/35S Chlorine, sediment, bad taste, odor, scale IL35BS 0110/35BS 2,500 1 X X X 0199/35BS Chlorine, sediment, bad taste, odor, scale QC350 QC3503 8, X X X X QC3502 Chlorine, chloramine, sediment, bad taste, odor QC350S QC350S 8, X X X X QC3502S Chlorine, chloramine, sediment, bad taste, odor, scale QC350F QC350F 8, X QC350-2 Chlorine, chloramine, sediment, bad taste, odor, scale QC500 QC , X X X X QC5002 Chlorine, chloramine, sediment, bad taste, odor QC500S QC500S 11, X X X X QC5002S Chlorine, chloramine, sediment, bad taste, odor, scale QC500F QC500F 11, X QC500-2 Chlorine, chloramine, sediment, bad taste, odor, scale QC500 Combo S 11, X X S Chlorine, chloramine, sediment, bad taste, odor, scale SMF Espresso 7500 SMF Espresso SMF CoffeePRO ,500 1 X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale ,000 2 X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale CP 15,000 5 X X X CP Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale ScaleOUT 05260W 40,000 5 X X X X Scale SMF IC , X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC , X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC ,000 5 X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC600S S 50,000 5 X X X X X X S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC620S S 100,000 5 X X X X X X S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC , X X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IC , X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor SMF IC , X X X X X Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor * numbers ending in S provide scale inhibition, which in some water conditions may cause tea to become cloudy. Continuing product improvements may necessitate E-21

22 Selecto Water Filtration Systems SMF IcePRO SMF IM600 SMF IM614 SlimeGUARD Spray SlimeGUARD Stick Gallon GPM Flow Rate Ice Machine Replacement Cartridge(s) Model Number Reduces/Eliminates SMF IcePRO IP 15,000 5 X IP Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IM S 75,000 7 X S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SMF IM S 150,000 7 X S Chlorine, chloramine, sediment, THMs, organics, tannins, bad taste, odor, scale SlimeGUARD Spary N/A N/A X N/A Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs. SlimeGUARD Stick N/A N/A X N/A Bacteria, mold, algae and fungus up to 3 months, ice makers up to 2400 lbs. SHURflo Inline Filters Number GPM Port Fitting Reduces/Eliminates SF210TO 2 1/4" plastic FPT taste, odor SF210TOS 2 1/4" plastic FPT taste, odor, sediment SF210SED 2 1/4" plastic FPT sediment SF210TOHQD 2 1/4" brass quick disconnect taste, odor SF210TOSHQD 2 1/4" brass quick disconnect taste, odor, sediment SF210SEDHQD 2 1/4" brass quick disconnect sediment SF210TOPQD 2 1/4" plastic quick disconnect taste, odor SF210TOSPQD 2 1/4" plastic quick disconnect taste, odor, sediment SF210SEDPQD 2 1/4" plastic quick disconnect sediment SF215TOCAT 2.5 1/4" plastic FPT SF215CATPQD 2.5 1/4" plastic quick disconnect Female plastic quick disconnects can be found in the Installation Products, fittings section. E-22 Continuing product improvements may necessitate

23 SHURflo Water Filtration Systems Number Single Standard 10" Filter System, 3/8" MPT threads SF With ball valve & gauge, no filters SF No fittings, no filters, single packed SF No fittings, no filters, bulk packed (12 to case) SF With ball valve & gauge, Granular Activated Carbon (GAC) element SF With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element Dual Standard 10" Filter Systems, 3/8" MPT threads SF With ball valve & gauge, no filters SF No fittings, no filters SF With ball valve & gauge, 5 micron sediment/gac element SF With ball valve & gauge, 5 micron sediment/gac/phosphate element SF With ball valve & gauge, Granular Activated Carbon (GAC) / Phosphate Element Dual Standard 10" UV Filter Systems, 3/8" MPT threads SF US System with ball valve & gauge, mechanical ballast, no filters SF US System, no fittings, mechanical ballast, no filters SF US System with ball valve & gauge, mech. ballast, 5 mic sed/gac element Dual Great White 10" x 20" Filter Systems, 3/4" MPT threads SF60010 With ball valve & gauge, no filters SF60020 No fittings, no filters SF600TOCL With ball valve & gauge, 5 micron sediment/gac element Dual Great White 10" Filter Systems, 3/4" MPT threads SF50010 With ball valve & gauge, no filters SF50020 No fittings, no filters SF500TOCL With ball valve & gauge, 5 micron sediment/gac element Dual Great White 10" UV Filter Systems, 3/4" MPT threads SF US System with ball valve & gauge, mechanical ballast, no filters SF US System, no fittings, mechanical ballast, no filters Dual Great White 20" Filter Systems, 3/4" MPT threads SF70010 With ball valve & gauge, no filters SF70020 No fittings, no filters Accessory Description UV light, 2.0 GPM, 8 watts, 2 pin UV light, 1.0 GPM, 6 watts, 2 pin UV light ballast, 2 pin Clip set (2) for UV light and inline filters Wrench for standard series sumps Wrench for Great White Series 10" sumps Wrench for Great White Series 20" sumps UV light Single Standard 10" Dual Standard 10" Dual Standard 10" UV Dual Great White 10" & 20" Dual Great White 10" Wrenches Continuing product improvements may necessitate E-23

24 SHURflo Replacement Filters Number Standard 10" Replacement Filters Standard 10" 0.5 micron modified molded carbon block FD Standard 10" 5 micron spun bonded polypropylene sediment cartridge Standard 10" 20 micron water washed coconut shell granular activated carbon (GAC) element Standard 10" 5 micron GAC w food grade hexametaphosphate Standard 10" phosphate crystal cartridge Standard 10" cation softening resin Standard 10" 20 micron spun bonded polypropylene sediment cartridge Standard 10" 4-8 micron modified molded block FD Standard 10" 4-8 micron modified molded block FD with siliphos softening Standard 20" 5 micron spun bonded polypropylene sediment cartridge Standard 20" 20 micron spun bonded polypropylene sediment cartridge Standard 20" 10 micron modified molded carbon block Standard 20" 0.5 micron modified molded carbon block Great White 10" 5 micron modified carbon block - FD Great White 10" 5 micron modified carbon block - FD with siliphos Great White 10" 0.5 micron carbon briquette Great White 10" 1 micron nom dual gradient density SED element - spun poly Great White 10" 5 micron granular activated carbon/sed element Great White 10" 5 micron SED element - pleated polypropylene Great White 20" 0.5 micron carbon briquette Great White 20" 1 micron nom dual gradient density SED element - spun poly Great White 20" 5 micron granular activated carbon/sed element Great White 20" 5 micron SED element pleated polypropylene LVPO-F1 starter kit: 5 micron carbon filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass LVPO-F2 starter kit: 5 micron sediment & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass LVPO-F3 starter kit: 5 micron carbon & phosphate filter NSF 42, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass LVPO-F4 starter kit: inline resin filter, SHURlock 3/8" barb ball balve, filter brackets, QD-bypass LVPO-F1, 5 micron carbon filter NSF 42, 3 GPM, 6000 gal life LVPO-F2, 5 micron sediment & phosphate filter NSF 42, 3 GPM, life depends on water conditions LVPO-F3, 5 micron carbon & phosphate filter NSF 42, 3 GPM, 6000 gal life LVPO-F4, inline resin filter,.5 GPM, 4400 grains or ppm PLF-1 inline 5 micron carbon filter NSF 42, 2 GPM, 5000 gal life LVPO starter kit LVPO-F1 LVPO-F2 LVPO-F3 LVPO-F4 E-24 Continuing product improvements may necessitate

25 SHURflo Accessories and Fittings Number Description LVPO filter QD-bypass LVPO filter brackets for slide track/wall mount, 1 pair LVPO filter to filter brackets, 1 pair LVPO filter brackets for tank mount, 1 pair Quick connect 3/8" barb ball valve set: gray handle for inlet, blue handle for outlet Quick connect 1/2" FPT with SS rings ball 90 valve set: gray handle for inlet, blue handle for outlet SS 30 psi water pressure reducer valve, 3/8" SS barb inlet/outlet SS 50 psi water pressure reducer valve, 3/8" SS barb inlet/outlet SS 65 psi water pressure reducer valve, 3/8" SS barb inlet/outlet SS 80 psi water pressure reducer valve, 3/8" SS barb inlet/outlet psi water pressure reducer valve w pressure gauge, 3/8" barb inlet/outlet Water strainer, 50 mesh SS screen, EPDM O-ring, 1/2" barb inlet, 1/2" FPST outlet.* Water strainer, 50 mesh SS screen, Buna O-ring, 1/2" barb inlet, 1/2" FPST outlet.* Water strainer, 50 mesh SS screen, Viton O-ring 1/2" barb inlet, 1/2" FPST outlet.* Water strainer, 50 mesh SS screen, EPDM O-ring 1/2" barb inlet, 1/2" FPST outlet.* Tank pressure switch, 25 psi on/40 psi off, NPT ports Tank pressure switch, 25 psi on/40 psi off, FPT ports, 2' wire harness Tank pressure switch, 25 psi on/40 psi off, push fit connectors, 2' wire harness Tank pressure switch, 25 psi on/40 psi off, 3/8" push fit connectors, 2' wire harness Low pressure switch, 3 psi on / 8 psi off, FPT ports Low pressure switch, 3 psi on / 8 psi off, push fit connectors, 2' wire harness /8" MPT x 1/2" straight barb, electric pump fitting, plastic /8" MPT x 3/8" straight barb, electric pump fitting, plastic /8" MPT x 1/2" elbow barb, electric pump fitting, plastic /8" MPT x 3/8" elbow barb, electric pump fitting, plastic /2" swivel nut x 1/2" straight barb, electric pump fitting, plastic /2" swivel nut x 3/8" straight barb, electric pump fitting, plastic /2" swivel nut x 1/4" straight barb, electric pump fitting, plastic /2" swivel nut x 1/2" elbow barb, electric pump fitting, plastic /2" swivel nut x 3/8" elbow barb, electric pump fitting, plastic /2" swivel nut x 1/4" elbow barb, electric pump fitting, plastic /8" MPT x 1/2" MPT adapter, electric pump fitting, plastic *Use adapter for 8000 Series pumps with 3/8" FPT Quick connect 90 valve set Water pressure reducer valve Water strainers Tank pressure switch Continuing product improvements may necessitate E-25

26 SHURflo Accessories and Fittings Number Description Hex swivel straight, polypropylene 1/2" FPT x 1/2" barb Hex swivel straight, polypropylene 1/2" FPT x 3/8" barb Wingnut swivel straight, polypropylene 1/2" FPT x 5/8" barb Wingnut swivel straight, polypropylene 1/2" FPT x 3/4" barb Wingnut swivel straight, polypropylene 1/2" FPT x 1/2" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 5/8" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 1/2" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/8" barb Wingnut swivel elbow, polypropylene, 1/2" FPT x 3/4" barb Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" barb Hex swivel elbow, polypropylene, 1/2" FPT x 3/8" barb Hex swivel elbow, polypropylene, 1/2" FPT x 1/2" MPT Adapter, nylon 1/2" FPT x 1/2" MPT Adapter, Nylon 1/2" FPT x 3/4" GSH (M) Adapter, Nylon 1/2" MPT x 3/4" barb Barb tee, polypropylene, 1/2" barb x 1/2" barb x 1/2" barb Hex swivel straight Wingnut swivel straight Wingnut swivel elbow Hex swivel elbow Adapter, FPT x MPT Adapter, FPT x GSH (M) Adapter, MPT x barb Barb tee E-26 Continuing product improvements may necessitate

27 Everpure Water Filtration Systems Everpure products can help you enjoy the taste without the waste of bottled water, and indirectly reduce waste by saving energy and prolonging the life of your equipment. Water analysis, site survey, selection of water appliances, service, maintenance and training are available. Everpure has over 200 models and model variations, and can customize a system to meet your needs. The most popular systems are shown here. All systems have a five year warranty, and cartridges have a one year limited warranty. NSF std. 42 & 53. QC71 Single-MC QC71 Twin-MC QC71 Triple-MC QC71 Quad-MC Coldrink 1-MC Coldrink 2-MC Coldrink 3-MC Dual HF Coldrink S-MC CB20-124E CB20-302E CB20-312E Insurice Single I2000 Insurice Twin I2000 Insurice Triple I4000 Insurice Quad I4000 E-Series 10" Prefilter E-Series 20" Prefilter SRX Scale Inhibitor Feeder IN-6 Inline Filter IN-10 Inline Filter Head and filter sold separately IN-12 Inline Filter EV SRX QL2-OW200L QL2-OCS QL3-BH QC7I Single-MH Continuing product improvements may necessitate E-27

28 Everpure Water Filtration Systems Did you know as little as a 1/8" layer of scale can reduce the efficiency of a coffee machine by 50%, resulting in twice the amount of electricity consumed? Gallon GPM Flow Rate Fountain Model Number Reduces/Eliminates QC71 Single-MC 2 EV , X X (1) EV Sediment, taste, odor, cyst QC71 Twin-MC 2 EV , X X (2) EV Sediment, taste, odor, cyst QC71 Triple-MC 2 EV ,000 5 X X (1) EV Sediment, taste, odor, cyst QC71 Quad-MC 2 EV , X X (1) EV Sediment, taste, odor, cyst Coffee Espresso/Capp. Ice Machine Drinking Water Combination Replacement Cartridge(s)/Kits QC71 Single-MH 2 EV ,000 1 X (1) EV Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) QC71 Twin-MH 2 EV ,000 1 X (2) EV Sediment, chlorine, taste, odor, cyst, scale (head only, filter sold separately) QC71 Single-ESO7 EV ,300 gr..5 X (1) EV Hardness QC71 Twin-ESO7 EV ,600 gr. 1 X (2) EV Hardness QC71 Triple-ESO7 EV ,900 gr. 1.5 X (3) EV Hardness Coldrink 1 MC 2 EV , X (1) EV Sediment, taste, odor, cyst (1) EV Coldrink 2 MC 2 EV , X (1) EV Sediment, taste, odor, cyst (2) EV Coldrink 3 MC 2 EV ,000 5 X (1) EV Sediment, taste, odor, cyst (3) EV Dual High Flow EV , X (2) EV Sediment, taste, odor, cyst Coldrink S-MC 2 (8) EV Dual High Flow EV , X (2) EV Sediment, taste, odor, cyst Coldrink M-XC 2 X (8) EV CB20-124E EV ,000 5 X X X X X (1) EV Chloramine, chlorine, taste, odor, cyst CB20-302E EV ,000 5 X X X X X (1) EV Chloramine, chlorine, taste, odor, cyst CB20-312E EV ,000 5 X X X X X (1) EV Chloramine, chlorine, taste, odor, cyst Insurice Single I EV , X (1) EV Sediment, chlorine, taste, odor, cyst, scale Insurice Twin I EV , X (2) EV Sediment, chlorine, taste, odor, cyst, scale Insurice Triple I EV ,000 5 X (3) EV Sediment, chlorine, taste, odor, cyst, scale Insurice Quad I EV , X (4) EV Sediment, chlorine, taste, odor, cyst, scale Insurice Single PFI EV , X (1) EV (1) EV Insurice Twin PFI EV , X (1) EV (2) EV Insurice Triple PFI EV ,000 5 X (1) EV (3) EV SRX Scale Inhibitor EV Depends N/A X X (1) EV Scale, deliming E-Series 10" Prefilter EV Depends N/A X X X X X X (1) EV Sediment E-Series 20" Prefilter EV Depends N/A X X X X X X (1) EV Sediment Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection Sediment, chlorine, taste, odor, cyst, scale, anitmicrobial protection E-28 Continuing product improvements may necessitate

29 Everpure Water Filtration Systems EV Head and filters sold separately EV EV EV EV EV EV EV EV Gallon GPM Flow Rate Fountain Coffee Esp./Capp./Tea Ice Machine Drinking Water Combination Replacement Cartridge(s) Model Number Reduces/Eliminates MC 2 -SO EV , X (1) EV Sediment, taste, odor, cyst, and softens (1) EV ,000 grains SO-24 Espresso EV ,500 2 X (1) DEV Hardness (softens 4,500 grains) SO-20 Housing EV , X (1) DEV Hardness (softens 1,500 grains) SO-10 Housing EV X (1) DEV Hardness (softens 750 grains) High Flow CSR Twin-MC 2 EV , X X X X X (1) EV (2) EV (1) EV High Flow CSR Triple-MC 2 *optional low pressure alarm High Flow CSR Quad- MC 2 *optional low pressure alarm High Flow CSR Plus-XC 2 (with 5 gallon reserve surge tank) HSD 440P Automatic Self Flushing Prefilter (120V) EV932806, *with alarm: EV EV943710, *with alarm: EV EV944720, *with alarm: EV ,000 5 X X X X X (1) EV (3) EV (1) EV , X X X X X (1) EV (4) EV (1) EV , X X X X X (1) EV (4) EV (1) EV Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale Sediment, taste, odor, cyst, scale EV N/A 10 X X X X X X (1) EV Sediment, turbidity, bacteria, virus (.025 micron) QL2-OW200L EV X (1) EV Sediment, chlorine, taste, odor, lead, THMs, asbestos, cyst, scale QL2-OCS 2 EV ,500.5 X (1) EV Sediment, chlorine, taste, odor, cyst, scale QL3-BH 2 EV ,000.5 X (1) EV Sediment, chlorine, taste, odor, cyst, scale Continuing product improvements may necessitate E-29

30 Everpure Claris Water Filtration Systems for Coffee, Espresso and Brewed Iced Tea To achieve the Golden Cup Standards of the Specialty Coffee Association of America, it is recommended that filtered water contain ppm of Total Dissolved Solids (TDS) for coffee and ~50 ppm for espresso for optimum flavor. Claris adjustable ion-selective filters enable you to tailor the carbonate hardness levels to deliver just the right amount of TDS for optimum coffee and espresso flavor while removing excessive and harmful hard water contaminants. Claris can be installed vertically or horizontally. The head features a built-in flush port, auto shut-off, adjustable by-pass, flow restrictor and backflow restrictor. The duo-blend by-pass technology has a 5-stage filtration process: Pre-filtration Carbonate hardness adjustment Fine filtration Highly efficient carbon block removes harmful contaminants and unpleasant odors and tastes Solid membrane filter removes particles down to 5 microns for equipment protection Heads and filters are sold separately. The CLARIS Flow Sensor monitors the filtrate volume to calculate and display the remaining filtration capacity in litres. When the filtration capacity or the maximum operation time has been reached the display unit indicates filter cartridge replacement. The programming and display unit shows: Residual capacity of installed filter cartridge Filtrate volume of the last five installed filter cartridges Operation time of the last five installed filter cartridges Total filtrate volume since Flow Sensor installation Claris Filter Family Gallon GPM Flow Rate Micron Rating Filter Number Reduces/Eliminates Claris Small EV X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris Medium EV X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris Large EV X X 1 Hardness, sediment, chlorine, taste, odor, scale Claris X-Large EV X X 1 Hardness, sediment, chlorine, taste, odor, scale Coffee Esp./Capp./Tea Case Qty. Number EV EV EV EV EV Description Claris Head 3/8" BSP Claris Head 3/8" QCF Claris Head 1/4" QCF Claris Flowmeter Claris Test Kit Claris Head Claris Flowmeter EV Claris Test Kit E-30 Continuing product improvements may necessitate

31 Everpure Costguard Water Filtration Systems DEV DEV DEV DEV DEV DEV Housing Number Filter Size Connection CGS-10 Single DEV " 3/8" FPT CGS-12 Dual DEV " 1/2" FPT CGS-20 Single DEV " 3/8" FPT CGS-22 Dual DEV " 1/2" FPT CGS-23 Parallel DEV " 3/8" FPT CGS-55 Single DEV " 1/2" FPT Costguard value priced filtration systems are designed for rigorous applications. Housings feature inlet/outlet shut-off valves, gauges, mounting bracket and hardware. Costguard filters are standard width and length that will fit most sump style filtration systems. Housing and filters are sold separately. Everpure Costguard Filters DEV DEV DEV Gallon GPM Flow Rate Micron Rating Fountain Coffee Esp./Capp./Tea Ice Machine Drinking Water Combination Case Qty. Filter Number Reduces/Eliminates CGT10S DEV , X X 12 Clorine, taste, odor, scale CGT20S DEV , X X 6 Clorine, taste, odor, scale CGT10 DEV , X 12 Clorine, taste, odor CGT20 DEV , X 6 Clorine, taste, odor CG510S DEV , X X 12 Clorine, taste, odor, scale, sediment CG520S DEV , X X 6 Clorine, taste, odor, scale, sediment CG510 DEV , X 12 Clorine, taste, odor, sediment CG520 DEV , X 6 Clorine, taste, odor, sediment CG5310S DEV , X X 12 Clorine, taste, odor, scale, sediment, cyst CG5320S DEV , X X 6 Clorine, taste, odor, scale, sediment, cyst CG5310 DEV , X 12 Clorine, taste, odor, sediment, cyst CG5320 DEV , X 6 Clorine, taste, odor, sediment, cyst Continuing product improvements may necessitate E-31

32 Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Model Reduces/Eliminates EV IN-10 2, Sediment, chlorine, taste, odor, cyst, scale EV IN-6 CGS Taste, odor, scale EV IN-6 PGS 6 mo..75 N/A 6 Scale EV IN-10-CK 5,000 Taste, odor, scale, slime EV IN-10-CS 3, Taste, odor EV IN-10-CC 2, Taste, odor EV IN-10-NSS 6-12 mo Sediment EV IN-10-CL Taste, odor, lead, cyst EV IN-9 CFS 1, Taste, odor, scale EV IN-15-CF 5, Taste, odor EV IN-15-CFS 5, Taste, odor, scale EV IN-15-CR 650 gr Hardness, taste, odor EV IN-10-UV 12 mo Bacteria, viruses EV IN-12 4, Sediment, chlorine, taste, odor, cyst, scale EV CB20-124E 15, Chloramine, chlorine, taste, odor, cyst EV CB20-302E 20, Chloramine, chlorine, taste, odor, cyst EV CB20-312E 60, Chloramine, chlorine, taste, odor, cyst EV SO-10 N/A 2 N/A 1 Hardness, scale EV SO gr. 2 N/A 0 Hardness, scale EV SO-204 N/A 2 N/A 0 Hardness, scale EV QCP 10L Sediment EV QCP 10L Chlorine, taste, odor, lead EV QCP 10GAC 1, Chlorine, taste, odor, lead EV QCP 10GAC 2, Chloramine, taste, odor EV QCP 10SED Chloramine, taste, odor EV QCP 10SEDS Depends Sediment, taste, odor EV QCP 10TSGAC 2, Scale Case Qty. E-32 Continuing product improvements may necessitate

33 Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces/Eliminates EV QCP 10TSGAC 1, Chloramine, taste, odor, scale EV " x 4" Big Bowl N/A 50/5 0 Sediment EV " x 4" Big Bowl N/A 20 25/1 6 Sediment EV EC110 10" Slimline N/A Sediment EV EC210 20" Slimline N/A Sediment EV " ECPI N/A 1 Sediment EV " ECPI N/A 1 Sediment EV " ECPI Big Bowl N/A Sediment EV DBG Depends Extraordinary taste and odor, high turbidity EV DM 1600 gr..5 0 Scale, high mineral content, low volume application EV NE Depends.5 1 Buffer/neutralizer for acidic (low ph) water, taste, odor EV OF Depends.5 1 Iron, sulfer, stains EV SO 2000 gr..5 1 High mineral content, low volume application EV TO 30, Extraordinary taste and odor, high turbidity EV ESO 6 Depends.5 0 Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor EV ESO 7 Depends.5 0 Hardness, buffering, chlorine, cyst, iron, sediment, scale, taste, odor EV I , Sediment, chlorine, taste, odor, cyst, microbial control, scale EV I , Sediment, chlorine, taste, odor, cyst, microbial control, scale EV BH2 3, Sediment, chlorine, taste, odor, cyst, microbial control, scale EV MC2 9, Class I particulates, chlorine, taste, odor, cyst EV XC2 12, Class I particulates, chlorine, taste, odor, cyst EV MH2 9, Sediment, chlorine, taste, odor, cyst, microbial control, scale EV CB5K 3, Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV CBS 6, Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure) EV CB5S 6, Sediment, chlorine, taste, odor, scale EV CB5S 3, Sediment, chlorine, taste, odor, scale EV CB5K 6, Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV CB5K 10, Sediment, chlorine, taste, odor, high turbidity, microbial control (for low flow/pressure) EV OCS2 1, Sediment, chlorine, taste, odor, cyst, microbial control, scale EV CB5 10, Sediment, chlorine, taste, odor, high turbidity (for low flow/pressure) EV CB5S 10, Sediment, chlorine, taste, odor, scale Continuing product improvements may necessitate E-33

34 Everpure Replacement Filters Sorted by Number Number Gallon GPM Flow Rate Micron Rating Case Qty. Model Reduces/Eliminates EV OW200L Sediment, chlorine, taste, odor, lead, scale, cyst, THMs EV MC2 Quad Kit 36, Class I particulates, chlorine, taste, odor, cyst EV XC2 Quad Kit 48, Class I particulates, chlorine, taste, odor, cyst EV OW2-Plus 1, Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale EV OW4-Plus 2, Sediment, chlorine, taste, odor, cyst, microbial control, lead, scale EV Microguard Pro 2 2, Sediment, chlorine, taste, odor, bacteria, asbestos, cyst EV Microguard Pro 4 3, Sediment, chlorine, taste, odor, bacteria, asbestos, cyst EV SS-10 6 mo. 6 N/A 0 Hardness, scale EV SS-IMF N/A 6 N/A 1 Hardness, scale EV MC2 Triple Kit 27, Class I particulates, chlorine, taste, odor, cyst Everpure Water System Cleaning Accessories Number Description EV JT flushing/sanitizing cartridge for ScaleKleen, bleach, or other sanitizing agent EV JT flushing/sanitizing cartridge EV ScaleKleen scale remover, 1.75 oz. EV ScaleKleen scale remover, 7 oz. EV ScaleKleen scale remover, 2.2 lb EV HFC-10 deliming agent EV EV E-34 Continuing product improvements may necessitate

35 Everpure Water System Heads EV EV EV EV EV EV EV EV EV EV EV EV Model Number Shut-Off Valve Mtg. Bracket Connection Flushing Valve Pressure Gauge QCP1 Single Head EV Yes No 1/4" QCF No No QCP2 Twin Head EV Yes No 1/4" QCF No No QCP3 Triple Head EV Yes No 1/4" QCF No No QCPC (1 head no shut-off) EV No No 1/4" QCF No No QL1 Single Head EV No Yes 3/8" MPT No No QL1 Single Head EV No Yes 3/8" QCF No No QL3B Single Head EV Yes Yes 3/8" MPT No No QC71 Single Head EV Yes Yes 3/8" MPT Yes Yes QC71 Twin Parallel Head EV Yes Yes 3/4" MPT Yes Yes QC71 Twin Plumbed Head EV Yes Yes 3/4" MPT Yes No QC71 Triple Parallel Head EV Yes Yes 3/4" MPT Yes Yes QC71 Quad Parallel Head EV Yes Yes 3/4" MPT Yes Yes QC71 Quad Head EV Yes Yes 3/4" MPT Yes Yes Claris Head 3/8" BSP EV Yes Yes 3/8" BSP Yes No Claris Head 3/8" QCF EV Yes Yes 3/8" QCF Yes No Claris Head 1/4" QCF EV Yes Yes 1/4" QCF Yes No Everpure Water System Accessories QCF = quick connect fitting, comparable to John Guest fittings Number DEV EV EV EV EV EV EV Description Smartworks water test kit Faucet kit Bottled water delivery system Filter usage monitor Surge tank, 9 gallon with fittings and tubing Spacer for SS-IMF cartridge Titration kit for Claris system Continuing product improvements may necessitate E-35

36 Bottled Water Dispenser At just 6" x 8" the Flojet Inlet Bottled Water Dispensing System is compact, affordable and perfect for dispensing bottled water to coffee machines, beverage dispensers, vending machines and carts in remote locations where water supply is inaccessible. This system has a universal seal cap, float switch for automatic shut-off when bottle is empty, built-in check valve to prevent back flow, and 20' discharge hose. Available in single or dual inlet. The dual inlet model has a T to draw from two bottles simultaneously. Flow rate: 1.0 GPM. Maximum pressure: 40 psi. BW1000A Number BW1000A BW1020A BW3000A BW3020A BW1520A BW3520A A A B A Description Single inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD Dual inlet, 1 GPM pump, 115 Volt, 20' discharge hose 1/4" OD Single inlet, 12V DC with 12" lead wires Dual inlet, 12V DC with 12" lead wires Dual inlet, appliance controller interface, 115 Volt Dual inlet, appliance controller interface, 12 Volt DC with 12" lead wires Conversion kit, single to dual inlet Conversion kit, legacy to A.C. interface Appliance controller Daisy chain (multi-hook up) 4-6 pin RJ-1, 9' cable Appliance Controller Unit is designed to work with applications drawing water from a reservoir or a bottled water system such as coffee machines and carbonator pumps at soft drink kiosks. It will sense water empty signal (0-5 VDC) coming from the water level sensor and turn connected devices ON or OFF. Audible alarm. 1 year warranty. Appliance controller can be mounted over or under the counter. Operating temperature: 32 F to 158 F. RJ-11 4 pins: daisy chain configuration. RJ-11 6 pins: BW interface. 6 pin RJ-11 cable: 9'. 2 AC outlets. 115V. Number Description A Appliance controller A 4-6 pin RJ-11 cable, 6' Lancer is a registered trademark of Lancer Corporation, San Antonio, Texas. SHURflo is a registered trademark of SHURflo, LLC, Cypress, California. McCann s is a registered trademark of McCann s Engineering, a Manitowoc Company, Los Angeles, California. Procon is a registered trademark of Procon Products, Standex International Corporation, Murfreesboro, Tennessee. Fluid-o-Tech is a registered trademark of Fluid-o-Tech International, Inc., Plantsville, Connecticut. Flojet is a registered trademark of ITT Industries, Foothill Ranch, California. CUNO, ScaleGARD, and Recipe Quality Water are trademarks of CUNO Incorporated, a 3M Company, Meriden, Connecticut. 3M is a trademark of 3M Company. Selecto is a registered trademark of Selecto, Inc., Suwanee, Georgia. Everpure is a registered trademark of Everpure, Inc., Hanover Park, Illinois. E-36 Continuing product improvements may necessitate