Appendix B Owner Provided Equipment

Transcription

1 Appendix B Owner Provided Equipment Appendix B

2 APPENDIX B OWNER PROVIDED EQUIPMENT PART 1 OWNER-FURNISHED PRODUCTS 1.1 PRECAST VAULTS - SPECIFICATION SECTION A. All Owner-supplied precast items are as indicated below in the procurement table. The vaults will be used for flow meters, process equipment and other services, as well as catch basins. Table 1 Owner Supplied Precast Vault/Catch Basin Schedule Vault Description Quantity Options 5-0 x 5-0 x 7-6 deep Precast Concrete Mag Meter Vault x 5-0 x 7-0 deep Precast Concrete Mag Meter Vault x 6-0 x 10-6 deep Precast Concrete Bladder Surge Tank Vault 8-0 x 6-0 x 7-8 deep Precast Concrete Booster Pump Control Valve Vault 4-0 x 4-0 x 7-0 deep Precast Concrete Pressure Relief Valve Vault 48 square x 48 deep Precast Concrete Drop Inlet 1 16 square x 24 deep Precast Concrete Drop Inlet x 4-0 x 8-0 deep Precast Concrete PRV & Pressure Relief Valve (Welcome Way) 36 square x 42 deep Precast Concrete Drop Inlet x 5-0 (Clear Opening) AL Double Access Hatch, Spring Assisted, H-20 Rated. Access Ladder with Ladder-up Option 5-0 x 5-0 (Clear Opening) AL Double Access Hatch, Spring Assisted, H-20 Rated. Access Ladder with Ladder-up Option 6-0 x 6-0 (Clear Opening) AL Double Access Hatch, Spring Assisted, 300 PSF Rated. Provide a minimum of (1) 12 inch grade rings for height adjustment. Access Ladder with Ladder-up Option and Fall Protection 6-0 x 6-0 (Clear Opening) AL Double Access Hatch Spring Assisted, H-20 Rated. Access Ladder with Ladder-up Option 4-0 x 4-0 (Clear Opening) AL Single Access Hatch, Spring Assisted, H-20 Rated. Access Ladder with Ladder-up Option 48 Square (Clear Opening) with Galvanized Steel Grating. 16 Square (Clear Opening) with Galvanized Steel Grating. 6-6 x 4-0 (Clear Opening) AL Double Access Hatch, Spring Assisted, H-20 Rated. Access Ladder with Ladder-up Option 36 Square (Clear Opening) with Galvanized Steel Grating Please Note: Minimum access hatch size and style are shown on the drawings (nominal clear opening shown, provide additional length/width as necessary to form a complete frame). Owner Provided Equipment Appendix B-1

3 B. Estimated Delivery Date 1. October 9 th, SUBMERSIBLE TURBINE PUMPS - SPECIFICATION SECTION (SEE ATTACHED) A. All Owner-supplied submersible turbine pumps and motors are indicated below: 1. Zolezzi Booster Pump Station Site: a. 2 Goulds 10RJLC Vertical Submersible Turbine b. Design Conditions 900 GPM at 460 FT TDH c. Centripro, 150 HP Motor, 460V/3Ph/60 Hz, 3600 RPM 2. ArrowCreek 1 Booster Pump Station Site: a. 2 Goulds 10RJLC Vertical Submersible Turbine b. Design Conditions 900 GPM at 350 FT TDH c. Centripro, 100 HP Motor, 460V/3Ph/60 Hz, 3600 RPM 3. Copper Cloud Booster Pump Station Site: a. 2 Goulds 10RJLC Vertical Submersible Turbine b. Design Conditions 900 GPM at 340 FT TDH c. Centripro, 100 HP Motor, 460V/3Ph/60 Hz, 3600 RPM B. Estimated Delivery Date 1. October 7 th, BOOSTER CAN UNIT STATION - SPECIFICATION SECTION (SEE ATTACHED) A. The Owner-furnished booster station can units at the following three existing locations: 1. Zolezzi Booster Pump Station Site: a. Two (2) - MAASS Midwest Model Number: MB,HD, B-16,18,10,FL-8, NPT-WT HDH-LOB-(5) 1.25 SWC-10-FL, ArrowCreek 1 Booster Pump Station Site: a. Two (2) - MAASS Midwest Model Number: MB,HD, B-16,18,10,FL-8, NPT-WT HDH-LOB-(5) 1.25 SWC-10-FL, Copper Cloud Booster Pump Station Site: a. Two (2) - MAASS Midwest Model Number: MB,HD, B-16,18,10,FL-8, NPT-WT HDH-LOB-(5) 1.25 SWC-10-FL,12. Owner Provided Equipment Appendix B-2

4 B. Estimated Delivery Date 1. October 7 th, BLADDER TYPE HYDROPNEUMATIC TANKS - SPECIFICATION SECTION (SEE ATTACHED) A. The Owner has pre-purchased two bladder-type surge control tanks for this project. The following sites each have one bladder-type hydropneumatic tank: 1. Zolezzi Booster Pump Station Site: a. 250 minimum nominal capacity gallons (model number to be provided later), ANSI 300 pound flange. 2. ArrowCreek 1 Booster Pump Station Site: b. 250 minimum nominal capacity gallons (suction side) (model number to be provided later), ANSI 150 pound flange. B. Estimated Delivery Date 1. October 23 rd, OWNER PROVIDED ELECTRICAL / INSTRUMENTATION ITEMS (SEE ATTACHED) A. The Owner has pre-purchased and will provide the following electrical / Instrumentation items at each site: 1. Zolezzi Booster Pump Station Site: a. Main Switch Board - (see attached) b. PLC and RTU - (model number to be provided later) c. Chart Recorder - (model number to be provided later) d. All CAT 5 Cables e. All Pressure Transducers - (model number to be provided later) f. All Pressure Switches - (model number to be provided later) g. Float Switch for installation in pump can - (model number to be provided later) h. Thermal Couples - (model number to be provided later) 2. ArrowCreek 1 Booster Pump Station Site: a. Main Switch Board - (see attached) b. PLC and RTU - (model number to be provided later) c. Chart Recorder - (model number to be provided later) Owner Provided Equipment Appendix B-3

5 d. All CAT 5 Cables e. All Pressure Transducers - (model number to be provided later) f. Switches - (model number to be provided later) g. Float Switch for installation in pump can - (model number to be provided later) h. Thermal Couples - (model number to be provided later) 3. Copper Cloud Booster Pump Station Site: a. Main Switch Board - (see attached) b. PLC and RTU - (model number to be provided later) c. All CAT 5 Cables d. All Pressure Transducers - (model number to be provided later) e. Switches - (model number to be provided later) f. Float Switch for installation in pump can- (model number to be provided later) g. Thermocouples - (model number to be provided later) B. Estimated Delivery Date 1. TBD 1.6 ITEMS NOT SUPPLIED BY OWNER: The following is a partial list of items not being supplied by the Owner, and is provided for the Contractor s reference only. 1. Magnetic flow meters 2. Sump pumps and integral float switches 3. Equipment pads 4. All conduits and wiring 5. Cla-Val control and relief valves 6. Lighting fixtures Owner Provided Equipment Appendix B-4

6 Submittal Review Form Project Name: TMWA ArrowCreek Drought Response Design Proj Contract No: Submittal No: 1 Resubmittal Received Submittal Title: Bid Item No.: Booster Pump Submittal Package Spec. No: 11300, Contractor/Subcontractor CH Spencer Routing Sequence Date Received Checked By Date Sent Orig. Number of Copies Prints Samples Mfg.Lit. CH Spencer Danny Beck 7/29/2015 TMWA 7/29/2015 Ray Kruth 8/3/2015 Stantec Consulting Ltd. 8/3/2015 David Diegle 8/3/2015 TMWA 8/3/2015 Scott Estes CH Spencer Submittal Compliance We have verified that the material or equipment contained in this submittal meets all the requirements specified or shown (no exceptions). We have verified that the material or equipment contained in this submittal meets all the requirements specified or shown, except for the following deviations (list deviations, attach separate sheet if necessary) Contractor Remarks Submittal Status A - NO EXCEPTION NOTED (Confirm) B - NOTE MARKINGS (Confirm) C - NOTE MARKINGS (Resubmit) D - REJECTED (Resubmit) E - UNREVIEWED / INFORMATION ON Engineer Remarks See attached Comments. GC Representative: Designer: David Diegle cc: Stantec Consulting Services Inc. Stantec Consulting Services Inc.

7 Submittal Review Comments Project Name: TMWA ArrowCreek Drought Response Design Project Submittal No: 1 Submittal Title: Resubmittal No.: Booster Pump Submittal Package Contract No.: Specification No: 11300, Date Received: 7/29/2015 Remarks 1.Pump bowls to be provided with exterior fusion epoxy coating per Spec. Section 2.2.A, rather than the Tnemec coating proposed. 2.Pumps to be provided with stainless steel intake screen (strainer marked as none on submittal). 3.Provide additional motor lead length if necessary so that splicing of the motor cable is not required within the pump can per spec. paragraph 2.4. Standard motor lead length is listed as 200, which may not be sufficient to extend beyond the pump can to a pull box. 4.Please submit written certification that proposed Tnemec 140 meets the NSF 372 requirement for low lead. If not, provide alternative coating. 5.Maass Midwest pump can to extend 24 above finish grade, not 18 as shown. 6.Maass Can suction side flange shall be ANSI Class 150, not Class 300 as show. 7.Maass Can shop drawing should indicate design test pressures. 8.Pump can wetted surfaces to be factory coated with NSF 61 and NSF 372 certified coating. No coating is listed for the pump can. David Diegle/Ray Kruth Review Engineer Stantec Consulting Services Inc. Stantec Consulting Services Inc.

8 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada TRUCKEE MEADOWS WATER AUTHORITY (Pumps, Motors, & Pitless Adapters for Arrowcreek Drought Response- Bid # )

9 C.H. Spencer & Company 1075 South Pioneer Road Salt Lake City, UT Phone: x.110 Fax: To: Truckee Meadows Water Authority Attn: Scott Estes Date: July 28, 2015 Reference: TMWA Project No Bid Date: July 23, 2015 Scott: Please see attached Submittal Package for the Booster Pump on the TMWA Pumps, Motors and Pitless Adapters for Arrowcreek Drought Response Project Section Zolezzi Booster Pump Station (Qty 2) Goulds 10RJLC Vertical Submersible Turbine - Design Conditions 900 GPM at 460 FT TDH - Centripro, 150 HP Motor, 460V/3Ph/60 Hz, 3600 RPM - Bronze Impellers -416 SS Collets - Tnemic 8 mills OD Coating - N/W Factory Testing -Spare Parts Section Arrow Creek Booster Pump Station (Qty 2) Goulds 10RJLC Vertical Submersible Turbine - Design Conditions 900 GPM at 350 FT TDH - Centripro, 100 HP Motor, 460V/3Ph/60 Hz, 3600 RPM - Bronze Impellers -416 SS Collets - Tnemic 8 mills OD Coating - N/W Factory Testing -Spare Parts Section Copper Cloud Booster Pump Station (Qty 2) Goulds 10RJLC Vertical Submersible Turbine - Design Conditions 900 GPM at 340 FT TDH - Centripro, 100 HP Motor, 460V/3Ph/60 Hz, 3600 RPM - Bronze Impellers -416 SS Collets - Tnemic 8 mills OD Coating - N/W Factory Testing -Spare Parts Let me know if you have any questions. Thanks Daniel Beck C.H. Spencer Sales Engineer Page 1 of 3

10 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada TABLE OF CONTENTS TAB # GENERAL PUMP DATA 1 SPECIFIC PUMP DATA 2 SPECIFIC MOTOR DATA 3 PUMP CANS & ACCESSORIES 4 WARRANTY 5

11 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada GENERAL PUMP DATA

12 Lineshaft and Submersible Turbine Pumps BTURBINE

13 TURBINE PUMP PRODUCTION

14 You not only get the latest in pump design and technology from Goulds Water Technology, you get more than 100 years of pump manufacturing know-how that includes most of the major innovations in pump engineering and materials. All our products reflect the engineering design advances for top efficiency and head generation. Our engineers are specialists, using computer assisted design and extensive test and research facilities. They develop the specifications that guide our inhouse pattern shop technicians in the development of precision turbine pattern equipment. The result is consistent casting accuracy, close tolerances and the quality needed to maintain water passage shape and pump efficiencies. Goulds Water Technology further controls the quality of its products in its own foundries. Here the molding, core work and Vitra-Glass enameling are closely supervised for tight quality standards. Our modern manufacturing facilities assure dimensionally consistent, high quality, fully machined parts, produced on a volume basis to bring down costs. Every impeller is precision balanced on a micro processor balance analyzer. Goulds Water Technology is one of the largest manufacturers in the turbine industry. From design to pattern shop to foundry to manufacturing to warehousing Goulds Water Technology is a completely integrated producer. Our network of turbine warehouses brings pumps and same day service to you. We offer full service on new units. Rebowling, rebuilding and repair on turbine pumps and submersible and centrifugal pumps. We are committed to service. We offer ready availability of complete pumps, repair parts and service. We are continually improving and expanding our turbine products warehouse network with locations in key areas. PAGE 3

15 LINESHAFT HEAD PER STAGE (FT.) RAH 1770 RPM 60 Hz 7RAL 7RAH 8RAH 7WAH 7WAL 8RAL 6CH 6CL 10RAH 9WAH 9WAL 8IH 8IL 7CL 7CH 8RJL 7TL 10WAL 13RAH 12WAH 12WAM 11CH 11CM 11WAH 11RAH 11CL 9BM 9RCH 10RJ 8RJH 8DIL 7TH 10RJL 9RCL 8DHH 13CM 13CH 12FRH 12DHH 12RJH 12RJM 12DHL 10LH 10DHH 9TL 9TH 12CHC 20BH 18CH 18BH 18BL 16DHH 18LH 16DM 16BHC 16DHL 15F 16BLC 14F 14RJH 14RJM 14DHL 14RHH 14RHM 14RJL 18HM 18DM 20EH 18DH 16F 16RGH 5WAH 5CH 5WAL 5CL 6DHH TL 5TH 6DHL FLOW (100 U.S. GPM) HEAD PER STAGE (m) RAL.8 7RAH 8RAL RPM 50 Hz 8RAH 1.5 7WAH 7WAL 6CH 2 9WAL 8IL 7CL 10RAH 9WAH 8IH 7CH 8RJL 10WAH 12RAH 13CL 13CHC 13WAH 11CH 13WAM 11WAH 11RAH 11CL 11CM 12RJM 9BN 9RCH 10RJ 10DHH 10RJL 8RJH 8DHL 7TH 9RCL 8DHH 9TL 9TH 14RJM 13CH 12RJH 12DHL 10LH 16BLC 14RJL FLOW (10 Cu. M/Hr) 20CH 20CL 20BH 18CH 18DM 18BH 18BL 16DM 16DHH 16BHC 16GH 14RJH 14DHL 12DHH 12FRH 14RHH 16DHL 14F 14RHM 15F 20EH 18LH 16GL 24EH 24EL 20GH 20GL 18HM 18DH PAGE 8

16 SUBMERSIBLE 1 Applications Goulds Water Technology combines the hydraulic engineering of turbine pumps matched to the hi-tech design of electric submersible motors. Features 1 Discharge Pipe Properly sized for optimum water velocities to insure peak hydraulic performance. 2 Discharge Bowl Several discharge sizes available for NPT or flanged pipe. 3 Discharge Bearing Extra long top protected bronze bearing insures positive shaft alignment and stabilization for extended life. 4 Intermediate Bowl Close grained Class 30 cast iron. Water passage glassed for maximum efficiency and abrasion resistance. 5 Impellers Designed for maximum efficiency with wide range hydraulic coverage. Precision balanced for smooth operation. 6 Upthrust Collar Designed for extra margin of safety against possible momentary upthrust occurring at startup. 7 Intermediate Bowl Bearings Reliable long life bronze or rubber bearing. 8 Lock Collets Accurately machined to insure positive locking of impeller to pump shaft. 9 Pump Shaft 100,000 PSI high tensile stainless steel provides strength and excellent corrosion resistance. Ground and polished for smooth bearing surface. 10 Suction Inlet Contoured for smooth flow entrance. Protected by an oversized stainless steel strainer to prevent entrance of damaging solids. 11 Suction Adapter Ductile iron provides for increased strength and positive motor alignment. Open area permits easy access to pump/motor coupling. 12 Pump/Motor Coupling Large stainless steel coupling accurately machined for perfect alignment, balance and power transmission. Submersible pumps and motors provide an extensive list of options versus other deep well pumping equipment systems. Advanced engineering designs and experience now assure units for long term pumping service. Water well applications provide the perfect opportunity to evaluate features and benefits of submersible equipment. PAGE

17 Hermetically Sealed Type A Hermetically Sealed Type motor utilizes windings of standard construction and insulation thickness. The windings are encased and Hermetically Sealed within the external shell casing on the outside and an internal tube or liner inside the bore. The Hermetically Sealed enclosure eliminates the possibility of water leakage into the winding the liquid medium circulates between the rotor and stator liner providing lubrication and cooling to the bearings. Submersible Options Goulds Water Technology can provide several options in pump and motor combinations to meet the exacting conditions of your applications: High temperature wells High horsepower, limited well diameters Motor sensing devices Water level indicators Special materials Special voltage motors Consult Goulds Water Technology Turbine Customer Service Department for details. Wet Winding Type A Wet Winding Type motor is one in which the motor windings are in direct contact with a liquid medium. The medium is clean, clear water. A pressure balancing system prevents exchange of the motor liquid medium and well water due to thermal expansion and contraction when the motor is operating. The liquid medium fills the inside of the motor and surrounds both the stator windings and the rotor. A completely water proof insulation is used on the magnet wire used for the stator windings. The liquid medium inside the motor air gap and coils acts as a heat transfer device by circulating through the windings and transferring heat to the external casing. Dissipation of this heat occurs as the well water flows at a required velocity over the external case. As is the case in all submersible type motors, the internal liquid medium is also used for bearing lubrication. Submersible Accessories: Valves Check Valves Gate Valves Flow Control Ball Valves Electrical Panels Furnas Panels V.F.D. Drivers Pitless Adapters Wire 12 to 0000 Heat Shrinks Splice Kits Tanks Well Heads Submersible Discharge Head Torque Arrestors Gauges Motor Shrouds PAGE 11

18 SUBMERSIBLE RAH RPM 60 Hz 10RAH 11RAH 9BM 13RAL 11CL HEAD PER STAGE (FT.) RAH 7RAL 7RAH 8RAL 8RAH 6CL 7WAH 7WAL 9WAH 9WAL 8IH 8IL 7CH 7CL 6CH 6DHH 8RJL 10WAL 8DHL 7TH 7TL 8RJH 9RCH 9RCL 10RJL 9TL 8DHH 9TH 50 5WAH 5CH 40 5WAL 5CL 5TH TL 6DHL FLOW (100 U.S. GPM) RPM 50 Hz 10WAL 11RAH 12WAH 11WAH 13RAH HEAD PER STAGE (m) RAH 8RAL 8RAH 9WAL 8IL 7WAH 7WAL 7CL 9WAH 8IH 7CH 8RJL 11CL 9BM 9RCH 9TH 10WAL 9RCL 9TL 10RJL 8DHH 8RJH 11CH 12CH 8RAH 7RAL 6CL 6CH 7TL 8DHL 7TH WAL 5WAH 5CL 5CH 5TL 5TH 6DHH 6DHL FLOW (10 Cu. M/Hr) PAGE 12

19 Hydraulic Performance The system requirements can be met with a choice of pump sizes and selections for the best hydraulic performance. The choice of pump and motor diameters, voltage and specs for varying well conditions provides additional opportunity to match the unit to all the requirements of the system. The availability of accessory items, cable and controls enables you to rely on Goulds Water Technology for units that provide top service. Submersibles for 1800 RPM through 20 are also available. PAGE 13

20 LINESHAFT/SUBMERSIBLES Parts List Standard Materials of Construction No. Description GWT No. Material Description 1 Discharge Head 1003 C.I. ASTM A48,CL 30B 2 Head Shaft Water Lube 2227 Stainless ASTM A582, Type 416 Oil Lube 2205 Steel AISI C Adjusting Nut 2130 Brass ASTM B16M C360 4 Gib Key 2242 Mild Steel ASTM A108, Gr Tension Nut Oil Lube Only 1187 Brass ASTM B584 C844 6 Tension Plate Oil Lube Only 1003 Cast Iron ASTM A48, CL 30B 7 Oiler Body Oil Lube Only 1425 Aluminum SAE 329 or Steel 8 Stuffing Box Water Lube 1003 Cast Iron ASTM A48, CL 30B 9 Stuffing Box Busing Water Lube 1109 Bronze ASTM B584 C89835 Federalloy III 10 Stuffing Box Stud Water Lube 2229 Stainless ASTM A276 Type Stuffing Box Stud Nut Water Lube 2229 Stainless ASTM A276 Type Stuffing Box Gasket Water Lube 5136 Garlock Brand Blue Guard 13 Stuffing Box Split Gland Water Lube 1193 Aluminum Bronze ASTM B148HT 14 Stuffing Box Slinger Water Lube 5121 Rubber 15 Packing 5026 Graphited Acrylic Yarn 16 Column Nipple 6501 Pipe ASTM A53 17 Lock Ring 1018 Ductile ASTM A536, Gr Reducer-Bushing 1003 Cast Iron ASTM A48, CL 30B 19 Companion Flange 1003 Cast Iron ASTM A48, CL 30B 20 Companion Flange Gasket 5136 Garlock Brand Blue Guard 21 Nameplate 3211 Stainless ASTM A240, Type Sole Plate 3201 Steel Plate ASTM A36 23 Column Pipe 6501 Pipe ASTM A53 24 Column Coupling 6501 Pipe ASTM A53 25 Tube Nipple 6518 Pipe Steel SCH80 ASTM A120 Gr. B 26 Enclosing Tube Bronze Construction 6518 Steel SCH80, ASTM A120, Gr. B Wood-Lined Construction 6518 Steel SCH80, ASTM A120, Gr. B 27 Oil Tube Coupling Wood-Lined Only 6518 Steel SCH80, ASTM A120, Gr. B 28 Lineshaft Bearing Bronze Construction 1109 Bronze ASTM B584 C903 Wood-Lined Construction Clear Heart Redwood Grade A W/L Sleeved 2205 Steel AISI C1045 with Type 304SS Sleeve 29 Lineshaft W/L Stainless 2227 Stainless ASTM A582, Type 416 Oil Lube 2205 Steel AISI C Lineshaft Coupling Water Lube 2242 Mild Steel ASTM A108, Gr Stainless 2218 Stainless ASTM A582, Type Water Lube Retainer Retainer 1102 Silicon Bronze ASTM B584 C876 Insert 5121 Rubber 32 Tube Centering Spider 5121 Rubber 33 Discharge Bowl 1003 Cast Iron ASTM A48, CL 30B 34 Discharge Bushing Water Lube 1109 Bronze ASTM B584 C89835 Federalloy III 35 Throttle Bushing Oil Lube 1109 Bronze ASTM B584 C89835 Federalloy III 36 Intermediate Bowl 6911 Cast Iron ASTM A48, CL 30B, Enameled 37 Top Inter Bowl 6911 Cast Iron ASTM A48, CL 30B, Enameled 38 Inter Bowl Bushing Bronze 1109 Bronze ASTM B584 C89835 Federalloy III Rubber 5121 Rubber 39 Wear Rings Optional Inter Bowl 1117 AL Bronze ASTM B148 C954 Impeller 1117 AL Bronze ASTM B148 C Impeller 1102 Silicon Bronze ASTM B584 C Taper Lock 2242 Mild Steel ASTM A108, Gr Suction Bowl 1003 Cast Iron ASTM A48, CL 30B 43 Suction Bushing 1109 Bronze ASTM B584 C89835 Federalloy III 44 Sand Collar 1109 Bronze ASTM B584 C89835 Federalloy III 45 Suction Strainer 6952 Galvanized ASTM A Plug 1046 Steel ASTM A197 Mall. Iron 47 Screw Bearing Bronze Construction 1109 Bronze ASTM B584 C89835 Federalloy III Wood-Lined Construction 2242 Mild Steel ASTM A108, Gr Bowl Shaft 2227 Stainless ASTM A582, Type Hex Bolt 2298 Steel SAEJ 429, Gr Lock Washer 2242 Steel ASTM A108, Gr Suction Adapter Submersible Only 1018 Ductile Iron Astm A536, Gr Adapter Plate Submersible Only (Optional) 1018 Ductile Iron ASTM A536, Gr Motor Coupling Submersible Only 2218 Stainless Steel ASTM A582, Type Motor Mounting Bolts Submersible Only 2229/2228 Stainless ASTM A276, Type 316/304SS 55 Suction Screen Submersible Only 3215 AISI 304 Stainless 56 Cable Guard Submersible Only 3215/6266 AISI 304 Stainless or Polyethylene (UHMW) 57 Discharge Bearing Submersible Only 1109 Bronze ASTM B584 C89835 Federalloy III 58 Discharge Bearing Plug Submersible Only 1046 Steel ASTM A197 Mall. Iron 59 Upthrust Washer Submersible Only 6266 Polyethylene (UHMW) PAGE 14

21 Services Municipal Wastewater Plants Commercial/Industrial Golf Courses/ Turf Irrigation Agricultural Irrigation Dewatering Mining Cooling Tower Water Parks Snowmaking Flood Control PAGE 15

22 UK Lubbock, TX Canada USA Belgium France Portugal Netherlands Germany Italy China Mexico Venezuela Philippines Singapore Australia Goulds Water Technology, headquartered in Seneca Falls, New York, designs, manufactures and services pumps, motors and accessories for industrial, agricultural, municipal, commercial and residential markets. Our sales offices and manufacturing facilities are located worldwide. Goulds Water Technology is a brand of Xylem, Inc., the world's largest and premier pump manufacturer, and offers the most complete range of pumps available. Turbine Distribution Centers: Phone Fax LUBBOCK P.O. Box 5487, Lubbock, TX MEMPHIS 1085 Stateline Road East, Suite 107, Southaven, MS ORLANDO 1150 Emma Oaks Trail, Suite 150, Lake Mary, FL FRESNO 3878 S. Willow Ave., #104, Fresno, CA Specifications & Special Projects: LUBBOCK CUSTOMER SERVICE CENTER Xylem Inc. P.O. Box 5487 Lubbock, TX Goulds is a registered trademark of Goulds Pumps, Inc. and is used under license Xylem Inc. BTURBINE January 2012

23 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada SPECIFIC PUMP DATA

24 Pump Data Sheet - Submersible 60 Hz Company: CH Spencer & Company Name: Zolezzi Date: 7/8/2015 TMWA Pump: Size: 10RJLC (4 stage) Type: Submersible Synch speed: 3600 rpm Curve: 3010 Speed: 3450 rpm Dia: in Impeller: Specific Speeds: Ns: 2760 Nss: --- Dimensions: Suction: --- Discharge: --- Vertical Turbine: Pump Limits: Bowl size: 9.5 in Max lateral: 0.75 in Thrust K factor: 7 lb/ft Temperature: 120 F Power: --- Pressure: 430 psi g Eye area: --- Sphere size: 0.68 in Search Criteria: Flow: 900 US gpm Fluid: Head: 460 ft Water Temperature: 68 F Density: lb/ft³ Vapor pressure: psi a Viscosity: cp Atm pressure: 14.7 psi a NPSHa: --- Motor: Standard: NEMA Enclosure: SUB Sizing criteria: Max Power on Design Curve Size: 150 hp Speed: 3600 Frame: 8 inch ---- Data Point ---- Flow: Head: 900 US gpm 461 ft Eff: 82.8% Power: NPSHr: 126 hp 34.5 ft ---- Design Curve ---- Shutoff head: Shutoff dp: Min flow: --- BEP: 682 ft 295 psi 942 US gpm NOL power: US gpm Head - ft in in 5.25 in Max Curve -- Max power: US gpm NPSHr - ft Performance Evaluation: Power - hp US gpm Discharge Sizes-6",8". Curves are certified for water at 60 F only. Consult factory for performance with any other fluid. Flow Speed Head Efficiency Power NPSHr US gpm rpm ft % hp ft PUMP-FLO Selected from catalog: Goulds Sub 60Hz Vers: 3.36

25 CH Spencer & Company DIMENSIONAL OUTLINE VIS-T 4 Stage 8x10RJLC Pump Data AD: AG: Size: 10RJLC Stages: 4 BL: CD: BowlShaft: 1.50" CL: N/A COL: 0.00" LineShaft: N/A DD: LineShaft Type: N/A Column: Standard DH: Column: 8" Threaded G: Bearing Spacing: N/A H: Section Length: N/A HH: Head: None J: Disch. NPT: N/A R: Suct.: ML: Seal: N/A TPL: N/A" Strainer: None UG: N/A SubBase: N/A V: W: Motor Diameter: 8" X: SD: Y: Z: Hydraulic Data Miscellaneous Motor Data Flow (gpm): 900 Thrust At Design (lb): 3269 Model: 8M1504 Pump Head (ft): Thrust At Shutoff (lb): 4817 Make: CentriPro TDH (ft): Pumping Level(in): 0 HP: 150 Speed (rpm): 3450 RPM: 3600 Fluid: Water Weight Type: SUB Temperature (F): 68 Pump (lb): 367 Efficiency: 85.6 Viscosity: Motor (lb): 683 Nominal Dia: 8" Spec.Grav: Total (lb): 1050 Voltage: 460 Version: 4.16P Customer: Date:

26 CH Spencer & Company Overall Pump Parameters HYDRAULIC ANALYSIS VIS-T 4 Stage 8x10RJLC Size and Model: 10RJLC Pump Operating Speed, RPM: 3450 Capacity, GPM: 900 Total Dynamic Head, Ft.: Total Pump Length, In.: Impeller Trim, In.: 6.1 Pump Type: Submersible Head Type: None Pump K-Factor: 7 Number of Stages: 4 Pumping Level, In.: 0.0 Bowl Data Total Bowl Length, In.: Bowl Diameter, In.: 9.5 Bowl Shaft Dia, In.: 1.50 Bowl Shaft Limit, HP: 498 Bowl Shaft Material: 416SS Column Data Column Diameter, In.: 8 Column Load, Lb.: Wall Thickness, In: Column Elongation, In.: 0.00 Shutoff Column Elongation, In.: 0.00 HorsePower Data Thrust Load Loss, Hp.: 0.00 Bowl HP At Design, Hp.: 126 Motor HorsePower, Hp.: 150 Other Data Hydraulic Thrust, Lb.: Thrust at Design, Lb.: Thrust at Shutoff, Lb.: 4817 Actual Head above Grade, Ft.: Suction Pressure, psi: 0.0 Shutoff Disc Pressure, psi: Column Loss, Ft.: 0.00 NPSHa, Ft.: Head Loss, Ft.: 0.65 NPSHr, Ft.: Total Loss, Ft.: 0.65 NPSH margin, Ft.: Efficiency Data (Efficiencies estimated not guaranteed) Bowl Efficiency: Pump Efficiency: Motor Efficiency: Overall Efficiency: KWH/1000 gallons: 2.05 Component Weights Bowl Weight, Lbs.: 367 Column Weight,Lbs.: 0 Head Weight, Lbs.: 0 Can Weight,Lbs.: 0 Motor Weight, Lbs.: 683 Total Pump Weight,Lbs.: 1050 Version: 4.16P Customer: Date:

27 CH Spencer & Company SECTIONAL VIS-T 4 Stage 8x10RJLC DISCHARGE HEAD ASSEMBLY ITEM NAME Code MATERIAL ASTM COLUMN AND LINESHAFT ASSEMBLY BOWL ASSEMBLY 614 COUPLING -- SUB MOTOR 2218 SST 416 A582M-95b 660 SHAFT- BOWL 2227 SST 416 A582M-95b 661 BOWL- DISCHARGE 8536 TNEMEC 140 ON IRON A BOWL- INTERMEDIATE 8536 TNEMEC 140 ON IRON A SUBADAPTER 1018 DUCTILE IRON A536-84(1999)e1 672 BEARING- INT BOWL 1109 FEDERALLOY BISMUTH BRZ B IMPELLER 1102 SILICON BRONZE C87600 B COLLET- IMPELLER 2242 CARBON STEEL 1018 A WEAR RING- BOWL 1128 BRONZE, AL C95400 B148-97e1 681 WEAR RING- IMPELLER 1128 BRONZE, AL C95400 B148-97e1 690 BEARING- SUCTION 1109 FEDERALLOY BISMUTH BRZ B GUARD- CABLE 3215 SST 304 A240M CAPSCREW- HEX (MOTOR)2228 SST 304 A CAPSCREW- HEX 2298 STEEL BOLTING GR 8 J SCREEN- SUCTION 3215 SST 304 A240M WASHER- UPTHRUST 6266 TIVAR 1000 x Version: 4.16P Customer: Date:

28 CH Spencer & Company ADDERS VIS-T 4 Stage 8x10RJLC ADDITIONAL PUMP COMPONENTS The following is a list of the additional components you ordered. Consult factory for any other components or services. Component Motor Adaptation Bronze 416 SS Collets Performance Test Bowl Coating (type 3) Tnemec mil Version: 4.16P Customer: Date:

29 Pump Data Sheet - Submersible 60 Hz Company: CH Spencer & Company Name: Aarow Creek Date: 7/8/2015 TMWA Pump: Size: 10RJLC (3 stage) Type: Submersible Synch speed: 3600 rpm Curve: 3010 Speed: 3450 rpm Dia: in Impeller: Specific Speeds: Ns: 2760 Nss: --- Dimensions: Suction: --- Discharge: --- Vertical Turbine: Pump Limits: Bowl size: 9.5 in Max lateral: 0.75 in Thrust K factor: 7 lb/ft Temperature: 120 F Power: --- Pressure: 430 psi g Eye area: --- Sphere size: 0.68 in Search Criteria: Flow: 900 US gpm Fluid: Head: 350 ft Water Temperature: 68 F Density: lb/ft³ Vapor pressure: psi a Viscosity: cp Atm pressure: 14.7 psi a NPSHa: --- Motor: Standard: NEMA Enclosure: SUB Sizing criteria: Max Power on Design Curve Size: 100 hp Speed: 3600 Frame: 8 inch Flow: Head: ---- Data Point US gpm 356 ft Eff: 82.6% Power: NPSHr: 97.5 hp 34.6 ft ---- Design Curve ---- Shutoff head: Shutoff dp: Min flow: --- BEP: 522 ft 226 psi 949 US gpm NOL power: US gpm -- Max Curve -- Max power: US gpm Head - ft in in 5.25 in NPSHr - ft Performance Evaluation: Power - hp US gpm Discharge Sizes-6",8". Curves are certified for water at 60 F only. Consult factory for performance with any other fluid. Flow Speed Head Efficiency Power NPSHr US gpm rpm ft % hp ft PUMP-FLO Selected from catalog: Goulds Sub 60Hz Vers: 3.36

30 CH Spencer & Company Aarow Creek DIMENSIONAL OUTLINE VIS-T 4 Stage 8x10RJLC Pump Data AD: 0.00 AG: Size: 10RJLC Stages: 4 BL: CD: BowlShaft: 1.50" CL: N/A COL: 0.00" LineShaft: N/A DD: LineShaft Type: N/A Column: Standard DH: Column: 8" Threaded G: Bearing Spacing: N/A H: Section Length: N/A HH: Head: None J: Disch. NPT: N/A R: Suct.: ML: Seal: N/A TPL: Strainer: None UG: N/A SubBase: N/A V: W: Motor Diameter: 8" X: SD: Y: Z: Hydraulic Data Miscellaneous Motor Data Flow (gpm): 900 Thrust At Design (lb): 2534 Model: 8M1004 Pump Head (ft): Thrust At Shutoff (lb): 4817 Make: CentriPro TDH (ft): Pumping Level(in): 0 HP: 100 Speed (rpm): 3450 RPM: 3600 Fluid: Water Weight Type: SUB Temperature (F): 68 Pump (lb): 367 Efficiency: 86.2 Viscosity: Motor (lb): 683 Nominal Dia: 8" Spec.Grav: Total (lb): 1050 Voltage: 460 Version: 4.16P TMWA Date:

31 CH Spencer & Company Aarow Creek Overall Pump Parameters HYDRAULIC ANALYSIS VIS-T 4 Stage 8x10RJLC Size and Model: 10RJLC Pump Operating Speed, RPM: 3450 Capacity, GPM: 900 Total Dynamic Head, Ft.: Total Pump Length, In.: Impeller Trim, In.: 6.1 Pump Type: Submersible Head Type: None Pump K-Factor: 7 Number of Stages: 4 Pumping Level, In.: 0.0 Bowl Data Total Bowl Length, In.: Bowl Diameter, In.: 9.5 Bowl Shaft Dia, In.: 1.50 Bowl Shaft Limit, HP: 499 Bowl Shaft Material: 416SS Column Data Column Diameter, In.: 8 Column Load, Lb.: Wall Thickness, In: Column Elongation, In.: 0.00 Shutoff Column Elongation, In.: 0.00 HorsePower Data Thrust Load Loss, Hp.: 0.00 Bowl HP At Design, Hp.: 97.5 Motor HorsePower, Hp.: 150 Other Data Hydraulic Thrust, Lb.: Thrust at Design, Lb.: Thrust at Shutoff, Lb.: 4817 Actual Head above Grade, Ft.: Suction Pressure, psi: 0.0 Shutoff Disc Pressure, psi: Column Loss, Ft.: 0.00 NPSHa, Ft.: Head Loss, Ft.: 0.65 NPSHr, Ft.: Total Loss, Ft.: 0.65 NPSH margin, Ft.: Efficiency Data (Efficiencies estimated not guaranteed) Bowl Efficiency: Pump Efficiency: Motor Efficiency: Overall Efficiency: KWH/1000 gallons: 1.58 Component Weights Bowl Weight, Lbs.: 367 Column Weight,Lbs.: 0 Head Weight, Lbs.: 0 Can Weight,Lbs.: 0 Motor Weight, Lbs.: 683 Total Pump Weight,Lbs.: 1050 Version: 4.16P TMWA Date:

32 CH Spencer & Company Aarow Creek SECTIONAL VIS-T 4 Stage 8x10RJLC DISCHARGE HEAD ASSEMBLY ITEM NAME Code MATERIAL ASTM COLUMN AND LINESHAFT ASSEMBLY BOWL ASSEMBLY 614 COUPLING -- SUB MOTOR 2218 SST 416 A582M-95b 660 SHAFT- BOWL 2227 SST 416 A582M-95b 661 BOWL- DISCHARGE 8536 TNEMEC 140 ON IRON A BOWL- INTERMEDIATE 8536 TNEMEC 140 ON IRON A SUBADAPTER 1018 DUCTILE IRON A536-84(1999)e1 672 BEARING- INT BOWL 1109 FEDERALLOY BISMUTH BRZ B IMPELLER 1102 SILICON BRONZE C87600 B COLLET- IMPELLER 2242 CARBON STEEL 1018 A WEAR RING- BOWL 1128 BRONZE, AL C95400 B148-97e1 681 WEAR RING- IMPELLER 1128 BRONZE, AL C95400 B148-97e1 690 BEARING- SUCTION 1109 FEDERALLOY BISMUTH BRZ B GUARD- CABLE 3215 SST 304 A240M CAPSCREW- HEX (MOTOR)2228 SST 304 A CAPSCREW- HEX 2298 STEEL BOLTING GR 8 J SCREEN- SUCTION 3215 SST 304 A240M WASHER- UPTHRUST 6266 TIVAR 1000 x Version: 4.16P TMWA Date:

33 CH Spencer & Company Aarow Creek ADDERS VIS-T 4 Stage 8x10RJLC ADDITIONAL PUMP COMPONENTS The following is a list of the additional components you ordered. Consult factory for any other components or services. Component 416 SS Collets Performance Test Bowl Coating (type 3) Tnemec mil Version: 4.16P TMWA Date:

34 Pump Data Sheet - Submersible 60 Hz Company: CH Spencer & Company Name: Cooper Cloud Date: 7/8/2015 TMWA Pump: Size: 10RJLC (3 stage) Type: Submersible Synch speed: 3600 rpm Curve: 3010 Speed: 3450 rpm Dia: in Impeller: Specific Speeds: Ns: 2760 Nss: --- Dimensions: Suction: --- Discharge: --- Vertical Turbine: Pump Limits: Bowl size: 9.5 in Max lateral: 0.75 in Thrust K factor: 7 lb/ft Temperature: 120 F Power: --- Pressure: 430 psi g Eye area: --- Sphere size: 0.68 in Search Criteria: Flow: 900 US gpm Fluid: Head: 340 ft Water Temperature: 68 F Density: lb/ft³ Vapor pressure: psi a Viscosity: cp Atm pressure: 14.7 psi a NPSHa: --- Motor: Standard: NEMA Enclosure: SUB Sizing criteria: Max Power on Design Curve Size: 100 hp Speed: 3600 Frame: 8 inch Flow: Head: ---- Data Point US gpm 345 ft Eff: 82.8% Power: NPSHr: 94.6 hp 34.5 ft ---- Design Curve ---- Shutoff head: Shutoff dp: Min flow: --- BEP: 511 ft 221 psi 942 US gpm NOL power: US gpm -- Max Curve -- Max power: US gpm Head - ft in in 5.25 in NPSHr - ft Performance Evaluation: Power - hp US gpm Discharge Sizes-6",8". Curves are certified for water at 60 F only. Consult factory for performance with any other fluid. Flow Speed Head Efficiency Power NPSHr US gpm rpm ft % hp ft PUMP-FLO Selected from catalog: Goulds Sub 60Hz Vers: 3.36

35 CH Spencer & Company Cooper Cloud DIMENSIONAL OUTLINE VIS-T 3 Stage 8x10RJLC Pump Data AD: 0.00 AG: Size: 10RJLC Stages: 3 BL: CD: BowlShaft: 1.50" CL: N/A COL: 0.00" LineShaft: N/A DD: LineShaft Type: N/A Column: Standard DH: Column: 8" Threaded G: Bearing Spacing: N/A H: Section Length: N/A HH: Head: None J: Disch. NPT: N/A R: Suct.: ML: Seal: N/A TPL: Strainer: None UG: N/A SubBase: N/A V: W: Motor Diameter: 8" X: SD: Y: Z: Hydraulic Data Miscellaneous Motor Data Flow (gpm): 900 Thrust At Design (lb): 2447 Model: 8M1004 Pump Head (ft): Thrust At Shutoff (lb): 3609 Make: CentriPro TDH (ft): Pumping Level(in): 0 HP: 100 Speed (rpm): 3450 RPM: 3600 Fluid: Water Weight Type: SUB Temperature (F): 68 Pump (lb): 307 Efficiency: 86.2 Viscosity: Motor (lb): 595 Nominal Dia: 8" Spec.Grav: Total (lb): 902 Voltage: 460 Version: 4.16P TMWA Date:

36 CH Spencer & Company Cooper Cloud Overall Pump Parameters HYDRAULIC ANALYSIS VIS-T 3 Stage 8x10RJLC Size and Model: 10RJLC Pump Operating Speed, RPM: 3450 Capacity, GPM: 900 Total Dynamic Head, Ft.: Total Pump Length, In.: Impeller Trim, In.: 6.1 Pump Type: Submersible Head Type: None Pump K-Factor: 7 Number of Stages: 3 Pumping Level, In.: 0.0 Bowl Data Total Bowl Length, In.: Bowl Diameter, In.: 9.5 Bowl Shaft Dia, In.: 1.50 Bowl Shaft Limit, HP: 499 Bowl Shaft Material: 416SS Column Data Column Diameter, In.: 8 Column Load, Lb.: Wall Thickness, In: Column Elongation, In.: 0.00 Shutoff Column Elongation, In.: 0.00 HorsePower Data Thrust Load Loss, Hp.: 0.00 Bowl HP At Design, Hp.: 94.6 Motor HorsePower, Hp.: 100 Other Data Hydraulic Thrust, Lb.: Thrust at Design, Lb.: Thrust at Shutoff, Lb.: 3609 Actual Head above Grade, Ft.: Suction Pressure, psi: 0.0 Shutoff Disc Pressure, psi: Column Loss, Ft.: 0.00 NPSHa, Ft.: Head Loss, Ft.: 0.65 NPSHr, Ft.: Total Loss, Ft.: 0.65 NPSH margin, Ft.: Efficiency Data (Efficiencies estimated not guaranteed) Bowl Efficiency: Pump Efficiency: Motor Efficiency: Overall Efficiency: KWH/1000 gallons: 1.52 Component Weights Bowl Weight, Lbs.: 307 Column Weight,Lbs.: 0 Head Weight, Lbs.: 0 Can Weight,Lbs.: 0 Motor Weight, Lbs.: 595 Total Pump Weight,Lbs.: 902 Version: 4.16P TMWA Date:

37 CH Spencer & Company Cooper Cloud SECTIONAL VIS-T 3 Stage 8x10RJLC DISCHARGE HEAD ASSEMBLY ITEM NAME Code MATERIAL ASTM COLUMN AND LINESHAFT ASSEMBLY BOWL ASSEMBLY 614 COUPLING -- SUB MOTOR 2218 SST 416 A582M-95b 660 SHAFT- BOWL 2227 SST 416 A582M-95b 661 BOWL- DISCHARGE 8536 TNEMEC 140 ON IRON A BOWL- INTERMEDIATE 8536 TNEMEC 140 ON IRON A SUBADAPTER 1018 DUCTILE IRON A536-84(1999)e1 672 BEARING- INT BOWL 1109 FEDERALLOY BISMUTH BRZ B IMPELLER 1102 SILICON BRONZE C87600 B COLLET- IMPELLER 2242 CARBON STEEL 1018 A WEAR RING- BOWL 1128 BRONZE, AL C95400 B148-97e1 681 WEAR RING- IMPELLER 1128 BRONZE, AL C95400 B148-97e1 690 BEARING- SUCTION 1109 FEDERALLOY BISMUTH BRZ B GUARD- CABLE 3215 SST 304 A240M CAPSCREW- HEX (MOTOR)2228 SST 304 A CAPSCREW- HEX 2298 STEEL BOLTING GR 8 J SCREEN- SUCTION 3215 SST 304 A240M WASHER- UPTHRUST 6266 TIVAR 1000 x Version: 4.16P TMWA Date:

38 CH Spencer & Company Cooper Cloud ADDERS VIS-T 3 Stage 8x10RJLC ADDITIONAL PUMP COMPONENTS The following is a list of the additional components you ordered. Consult factory for any other components or services. Component Motor Adaptation Bronze 416 SS Collets Performance Test Bowl Coating (type 3) Tnemec mil Version: 4.16P TMWA Date:

39 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada SPECIFIC MOTOR DATA

40 6-10" Submersible Motors FOR 6" AND LARGER DEEP WELL PUMPS BRCP6SM

41 Commercial, Irrigation and Agricultural Water CentriPro GENERAL FEATURES OF CANNED AND REWINDABLE WATER-TIGHT MOTORS 6" Canned Design Motor Features Replaceable Plug-in Motor Lead All 6 motor leads are stranded copper for flexibility and strength. Leads are 150 long and field replaceable. Insulation The canned motor s stator coil is mounted in a stainless steel frame and is completely sealed in a stainless steel cylinder. The coil wire features moisture resistant insulation which is completely water-proofed for long life. Heat Resistant The space between the stator's stainless steel protective can and its frame is filled with a specially formulated patented resin that protects the motor against thermal fluctuation and internal stress. 95º F (35º C) Water Temperature (CANNED TYPE: 6", 5 50 HP) The motors operate with a minimum flow rate of 0.5 ft./sec. (0.15 m/sec) in water temperature up to 95º F (35º C) without any derating of horsepower. This 95º F (35º C) temperature is 18º F (10º C) higher than NEMA standards. 8-10" Rewindable Water-Tight Motor Features Insulation Wire The coil conductor insulation material is a specially developed denatured polypropylene, which offers excellent leak-resistant characteristics. Three barriers are applied to the copper conductors to provide complete insulation against the motor s cooling fluid. This design is the result of extensive research and is of superior quality. It insures that CentriPro motors will have an extremely long service life. Motor Features - Both Designs Sand Resistant Slinger and Lip Seals CentriPro submersible motors feature double-row, grease packed, lip seals to prevent sand from entering the motor. A carbon steel slinger with a baked on epoxy coating prevents sand from entering the lip seal area. Additional protection against sand intrusion is provided by the close tolerance slinger guide with a.02 fit. This design CONSTRUCTION AND INSULATION DETAILS is field-proven in West Texas wells which are considered to be some of the worst sandy well applications. Best of all, these features are standard for a CentriPro motor, so there is no need to stock one motor for clean wells and another more expensive motor for the more abrasive, sandy jobs. High Torque Characteristics The stator laminations are constructed of high quality, electrical grade, silicon steel which provide high torque even when the motor is subjected to nominal voltage variations. Balancing The rotor balance rings (one on each end of the rotor) allow for excellent dynamic balance for the rotating element of the motor. Carbon Sleeve Bearings Two carbon, water-lubricated, guide bearings are used to properly align the shaft. The bearings have a large surface area to better support the shaft, reducing whipping, while acting as a steady bushing. Water-Filled Design The internal cooling water is mixed with antifreeze and antirust liquid to allow the motor to be stored at 22º F ( 30º C). Two water plugs are provided for filling or draining the anti-freeze fluid during maintenance. These plugs are also used to top off and to check the water level. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated carbon steel housings), shaft and bolts. All other motor parts are finished with the baked epoxy coating. Baked Epoxy Coating All external and internal cast iron parts are coated with a baked epoxy resin that provides excellent resistance to water and corrosion. Quality Control All CentriPro submersible motors are manufactured and tested under the most stringent quality control procedures, providing long service life and trouble-free operation. TYPE 6" CANNED DESIGN 8-10" REWINDABLE WATER-TIGHT DESIGN Construction Slot Insulation PAGE 4

42 Commercial, Irrigation and Agricultural Water CentriPro 6" CANNED DESIGN THREE PHASE, 5-30 HP, 230 AND 460V DUAL VOLTAGE MOTORS With DUAL VOLTAGE SUBMERSIBLE MOTORS IN YOUR STOCK, you no longer have to worry about inventory balance between 230V and 460V. DUAL VOLTAGE SUBMERSIBLE MOTORS have all the same specifications of canned type motors plus the unique feature of dual voltage. Motor voltage can be changed from 460V to 230V or from 230V to 460V on three-phase, 5 through 30 HP motors by changing voltage plugs. Voltage plugs are clearly and permanently marked as 230V or 460V. Each plug is usable on all 5 through 30 HP motors. Voltage Plug Order Numbers: PLUG-230V PLUG-460V 5 30 HP (3.7kW 22kW), 3Ø STANDARD SPECIFICATIONS Cable Connection : Plug-In Type Water Environment Cable Length : 150 inch (3.8 m) Flow Rate : 0.5 ft./sec. minimum Shaft : NEMA Splined ph Level : Flange : NEMA Standard Maximum Temperature : 95º F (35º C) Speed : 2P 3600/3000 RPM (60/50 Hz) Service Factor 1.15 : at 230, 460V/60Hz 1.00 : at 208, 380V/60 Hz and 380, 400, 415V/50 Hz PAGE 5

43 Commercial, Irrigation and Agricultural Water CentriPro 8-10" REWINDABLE WATER-TIGHT MOTORS 2 POLE 3600/3000 RPM DESCRIPTION OF WATER TIGHT INSULATION WIRE ➀ The reliability of submersible motors depends on their insulation characteristics. CentriPro 8-10 motors are the result of years of continuous research and development. Our rewindable water-tight motors feature excellent insulation characteristics thanks to their new patented, water-tight, insulated magnet wire. The insulation material is a specially developed denatured polypropylene applied over a special enamel layer. An external nylon sheath is applied over this polypropylene layer for extra mechanical protection. These three barriers are applied to copper conductors for complete insulation from the motor s cooling fluid. This insures that CentriPro motors will have an extremely long service life. STANDARD SPECIFICATIONS ➀ 8-10" motors do not have a factory installed ground lead. *See dimensional data for correct variations HP (30 kw kw) 3Ø 2P 3,600/3,000 RPM (60/50 Hz) Cable Connection Direct to Stator Cable Length 200 inch (5 m) Shaft 2P Splined HP ( kw) Keyed 200 HP (150 kw) Flange NEMA Standard Speed 60 Hz 2P 3600 RPM 50 Hz 2P 3000 RPM Water Environment Minimum Flow Rate 0.5 ft./sec. (0.15 m/sec.) ph Level Maximum Temperature 77º F (25º C) Service Factor Service Factor Motor HP 380, 400, 460V / 60 Hz 2P 415V / 50 Hz PAGE 7

44 TECHNICAL BROCHURE BCP6-10MTR R2 FEATURES SINGLE PHASE: Single Phase, 6 motors available in 5 15 HP, 230 volt models. Require CentriPro Control Boxes as shown on Order Number chart. THREE PHASE: Three Phase, 6, 5 30 HP, 230 and 460 volt models have an exclusive voltage change plug feature. Stock one model and a different voltage plug to reduce inventory cost. Change Plug Order Numbers are: PLUG-230V PLUG-460V 6 10 Three Phase available from HP, see charts for available voltages. NOTE: See color brochure (BRCP6SM) for more information and cutaway views. NSF NSF/ANSI STANDARD 61 Drinking Water System Components - Health Effects 6" Single Phase Motors 6-10" Three Phase Motors

45 Commercial, Irrigation and Agricultural Water CentriPro 6" SINGLE PHASE MOTORS AND REQUIRED CONTROL BOXES Motor Motor Dia. Rated Input Service Factor L.R. Control Box HP kw Volts Phase S.F. Order No. vs Flange Dia. Amps Watts Amps Watts Amps Order No. ➀ 6M CB05MC3R 6M CB07MC3R x M CB10MC3R 6M CB15MC3R ➀ NEMA 3R control boxes will be replacing the current models. 6-10" THREE PHASE MOTORS Motor Motor Dia. Rated Input Service Factor L.R. HP kw Volts Phase S.F. Order No. vs Flange Dia. Amps Watts Amps Watts Amps 6M M M M M M M M M M M " x 6" M M M M M M M M M M M " x 6" 66M M " x 6" 86M M M " x 8" 8M M M "x 10" HP, 3 Phase 230 and 460 Motors have adjustable voltage feature, change voltage plugs to convert from 230V to 460V operation. Spare Change Plug Order No's are: PLUG-230V or PLUG-460V. PAGE 2

46 Commercial, Irrigation and Agricultural Water CentriPro 6" SINGLE PHASE MOTORS Motor F.L. KVA Resistance - Ohms HP kw Volts Phase Order No. Efficiency % Code R - Y B - Y R - B 6M G M F M E M D " THREE PHASE MOTORS Motor F.L. KVA Line - Line Time Delay Fuse HP kw Volts Phase Order No. Efficiency % Code Resistance Standard Dual Element 6M K M K M K M J M J M J M K M K M K M K M K M K M J M J M J M K M K M K M J M K M K M H M J M K M J M H M H M G M G M F PAGE 3

47 Commercial, Irrigation and Agricultural Water CentriPro GENERAL FEATURES OF CANNED AND REWINDABLE WATER-TIGHT MOTORS 6" AND 8"X6" CANNED DESIGN MOTOR FEATURES Replaceable Plug-in Motor Lead All 6 motor leads are stranded copper for flexibility and strength. Leads are 150 long and field replaceable. Insulation The canned motor s stator coil is mounted in a stainless steel frame and is completely sealed in a stainless steel cylinder. The coil wire features moisture resistant insulation which is completely water-proofed for long life. Heat Resistant The space between the stator's stainless steel protective can and its frame is filled with a specially formulated patented resin that protects the motor against thermal fluctuation and internal stress. 8-10" REWINDABLE WATER-TIGHT MOTOR FEATURES Insulation Wire The coil conductor insulation material is a specially developed denatured polypropylene, which offers excellent leak-resistant characteristics. Three barriers are applied to the copper conductors to provide complete insulation against the motor s cooling fluid. This design is the result of extensive research and is of superior quality. It insures that CentriPro motors will have an extremely long service life. MOTOR FEATURES - BOTH DESIGNS Maximum Water Temperature 6, 8 & 10" Motors Size HP Temperature Range Minimum Flow Rate Ph Range 6" º F (35º C).5 Ft/sec x6" º F (25º C).5 Ft/sec " º F (25º C).5 Ft/sec " º F (25º C).5 Ft/sec Sand Resistant Slinger and Lip Seals CentriPro submersible motors feature double-row, grease packed, lip seals to prevent sand from entering the motor. A carbon steel slinger with a baked on epoxy coating prevents sand from entering the lip seal area. Additional protection against sand intrusion is provided by the close tolerance slinger guide with a.02 fit. This design is field-proven in West Texas wells which are considered to be some of the worst sandy well applications. Best of all, these features are standard for a CentriPro motor, so there is no need to stock one motor for clean wells and another more expensive motor for the more abrasive, sandy jobs. High Torque Characteristics The stator laminations are constructed of high quality, electrical grade, silicon steel which provide high torque even when the motor is subjected to nominal voltage variations. Balancing The rotor balance rings (one on each end of the rotor) allow for excellent dynamic balance for the rotating element of the motor. Carbon Sleeve Bearings Two carbon, water-lubricated, guide bearings are used to properly align the shaft. The bearings have a large surface area to better support the shaft, reducing whipping, while acting as a steady bushing. Water-Filled Design The internal cooling water is mixed with antifreeze and antirust liquid to allow the motor to be stored at 22º F ( 30º C). Two water plugs are provided for filling or draining the anti-freeze fluid during maintenance. These plugs are also used to top off and to check the water level. Complete Corrosion and Water-Tight Protection All main motor components are made of stainless steel: including the can housing (water tight type motors have baked epoxy coated carbon steel housings), shaft and bolts. All other motor parts are finished with the baked epoxy coating. Baked Epoxy Coating All external and internal cast iron parts are coated with a baked epoxy resin that provides excellent resistance to water and corrosion. Quality Control All CentriPro submersible motors are manufactured and tested under the most stringent quality control procedures, providing long service life and trouble-free operation. CONSTRUCTION AND INSULATION DETAILS TYPE 6" and 8"x6" CANNED DESIGN 8-10" REWINDABLE WATER-TIGHT DESIGN Construction Slot Insulation PAGE 4

48 Commercial, Irrigation and Agricultural Water CentriPro SPECIAL TECHNOLOGY HIGH PERFORMANCE THRUST BEARING APPLICATION Motor Output Bearing Number Size HP kw Type of Shoes 6" A 3 6" B " C 6 10" C 8 Number Part Name 1 Pivot Shoe 2 Bearing Frame 3 Carbon Disc 4 Metal Support 5 Metal Frame 6 Thrust Plate 7 Slide Plate 8 Up Thrust Bearing The field proven KINGSBURY design thrust bearing creates a wedge of water between the pivot shoe and carbon disc. Our innovative design permits high thrust loads to be placed on the bearings while showing no measurable wear after several years of severe duty operation. This allows for long pumping life, virtual trouble free operation and low maintenance. For all 6" motors, the 300 lbs. maximum continuous up thrust is absorbed between the upper carbon sleeve bearing and the rotor balance ring. For all 8" 10" motors, the 1000 lbs. maximum continuous up thrust is carried between the upper slide plate and the separate up thrust carbon bearing. 2P Motor Down Thrust Up Thrust Size lbs. kg lbs. kg 6" ,500 1, HP *(450) *(200) 6" ,000 2, HP *(450) *(200) 8x6" ,000 2, HP *(450) *(200) 10,000 4,540 1, " ** ** ** ** (5,000) (2,270) (1,500) (680) 10" 10,000 4,540 1, Note: 1. Thrust ratings showed are continuous except for values marked *. 2. * Momentary rating (3 minutes maximum). 3. ** 8" motor - 6" Flange when using standard stainless steel bolts (B&M), has a thrust value of 5,000 lbs. A thrust value of 10,000 lbs. can be obtained by using high tensile stainless steel bolts (ASTM F593G). PAGE 5

49 Commercial, Irrigation and Agricultural Water CentriPro REWINDABLE WATER-TIGHT DESIGN MOTORS SIZE AND WEIGHT - 2 POLE 3600 RPM 60 Hz 3000 RPM 50 Hz L D Motor Output D L Net Weight Size HP kw inch (mm) inch mm lbs. kg 8" (191) " (216.5) (*) 6 inch flange. **Gross Weight: See page 12. CABLE SIZE AND TYPE - 2 POLE 3600 RPM 60 Hz 3000 RPM 50 Hz 200 inch (5 m) Lead Wire Standard Length (Round 1 Stranded Conductor) Motor Size Output 460V, 415V, 400V, 380V Lead Wire Size Cable Diameter HP kw mm 2 AWG inch mm # " # # " # Type of Lead Wire 600V Class Ethylene Propylene rubber insulated chloroprene cabtyre cable. PAGE 8

50 Commercial, Irrigation and Agricultural Water CentriPro DIMENSIONAL DATA 8", 3600 RPM, 2 POLE (6" FLANGE) 8", 3600 RPM, 2 POLE (8" FLANGE) Size 8"x8" 8"x6" Output C L Phase HP kw inch mm inch mm PAGE 10

51 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada PUMPS/ CANS & ACCESSORIES

52

53 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada THE FOLLOWING ACCESSORIES WILL BE PROVIDED Spare Parts: -Each Model of Pump will be provided with one set of bearings and all gaskets/o-rings. Pump Can Testing: Each Pump can will be hydrostatically tested, test results will be supplied prior to shipment to the design engineer. Pump Bowl Assembly Each Bowl Assembly will have a N/W Factory Performance Test Supplied, pumps will not ship from the manufactures facility without engineers prior approval.

54 C.H. Spencer & Company 95 Isidor Court Sparks, Nevada WARRANTY

55 Terms & Conditions General Provisions WARRANTY - Company warrants title to the product(s) and, except as noted with respect to items not of Company s manufacturer, also warrants the product(s) on date of shipment to Purchaser, to be of the kind and quality described herein, and free of defects in workmanship and material. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, AND CONSTITUTES THE ONLY WARRANTY OF COMPANY WITH RESPECT TO THE PRODUCT(S). If within one year from date of initial operation, but not more than eighteen months from date of shipment by Company of any item of product(s), Purchaser discovers that such item was not as warranted above and promptly notifies Company in writing thereof, Company shall remedy such nonconformance by, at Company s option, adjustment or repair or replacement of the item and any affected part of the product(s). Purchaser shall assume all responsibility and expense for removal, reinstallation, and freight in connection with the foregoing remedies. The same obligations and conditions shall extend to replacement parts furnished by Company hereunder. Company shall have the right of disposal of parts replaced by it. Purchaser agrees to notify Company, in writing, of any apparent defects in design, material or workmanship, prior to performing any corrective action back chargeable to the Company. Purchaser shall provide a detailed estimate of the material, labor costs associated with proposed remedy for expeditious review and approval by the Company. ANY SEPARATELY LISTED ITEM OF THE PRODUCT(S) WHICH IS NOT MANUFACTURED BY THE COMPANY IS NOT WARRANTED BY COMPANY and shall be covered only by the express warranty, if any, of the manufacturer thereof. THIS STATES PURCHASER S EXCLUSIVE REMEDY AGAINST COMPANY AND ITS SUPPLIERS RELATING TO THE PRODUCT(S) WHETHER IN CONTRACT OR IN TORT OR UNDER ANY OTHER LEGAL THEORY, AND WHETHER ARISING OUT OF WARRANTIES, REPRESENTATIONS, INSTRUCTIONS, INSTALLATIONS OR DEFECTS FROM ANY CAUSE. Company and its suppliers shall have no obligation as to any product which has been improperly stored or handled, or which has not been operated or maintained according to instructions in Company or supplier furnished manuals. PATENTS - Company shall pay costs and damages finally awarded in any suit against Purchaser or its vendees to the extent based upon a finding that the design or construction of the product(s) as furnished infringes a United States patent (except infringement occurring as a result of incorporating a design or modification at Purchaser s request) provided that Purchaser promptly notifies Company of any change of such infringement, and Company is given the right at its expense to settle such charge and to defend or control the defense of any suit based upon such charge. THIS PARAGRAPH SETS FORTH COMPANY S EXCLUSIVE LIABILITY WITH RESPECT TO PATENTS. BUYER DATA - Timely performance is contingent upon the Purchaser supplying to the Company, when needed, all required technical information, including drawing approval, and all required commercial documentation. NUCLEAR - Purchaser represents and warrants that the product(s) covered by this contract shall not be used in or in connection with a nuclear facility or application. NONCANCELLATION - Purchaser may not cancel or terminate for convenience, or direct suspension of manufacture, except on mutually acceptable terms. DELAYS - If Company suffers delay in performance due to any cause beyond its control, including but not limited to act of God, war, act or failure to act of government, act or omission of Purchaser, fire flood, strike or labor troubles, sabotage, or delay in obtaining from others suitable services, materials, components, equipment or transportation, the time of performance shall be extended a period of time equal to the period of the delay and its consequences. Company will give to Purchaser notice in writing within a reasonable time after Company becomes aware of any such delay. STORAGE - Any item of the product(s) on which manufacture or shipment is delayed by causes within Purchaser s control, or by causes which affect Purchaser s ability to receive the product(s), may be placed in storage by Company for Purchaser s account and risk. SHIPMENT - The term shipment means delivery to the initial carrier in accordance with the delivery terms of this order. Company may make partial shipments. Company shall select method of transportation and route, unless terms are f.o.b. point of shipment and Purchaser specifies the method and route and is to pay the freight costs in addition to the price. When terms are f.o.b. destination or freight allowed to destination, destination means common carrier delivery point (within the continental United States, excluding Alaska) nearest the destination. For movement outside the United States, Company shall arrange for inland carriage to port of exit and shall cooperate with Purchaser s agents in making necessary arrangements for overseas carriage and preparing necessary documents. SPECIAL SHIPPING DEVICES - On shipments to a destination in the continental United States or Canada, Company has the right to add to the invoice, as a separate item, the value of any special shipping device (barrel, reel, tarpaulin, cradle, crib and the like) used to contain or protect the product(s) invoiced, while in transit. Full credit will be given on the return to Company of the device in a reusable condition, f.o.b. destination, freight prepaid. TITLE AND INSURANCE - Title to the product(s) and risk of loss or damage shall pass to Purchaser at the f.o.b. point, except that a security interest in the product(s) and proceeds and any replacement shall remain in Company, regardless of mode of attachment to realty or other property, until the full price has been paid in cash. Purchaser agrees to do all acts necessary to perfect and maintain said security interest, and to protect Company's interest by adequately insuring the product(s) against loss or damage from any external cause with Company named as insured or co-insured. made. If shipment is delayed by Purchaser, date of readiness for shipment shall be deemed to be date of shipment for payment purposes. If at any time in Company s judgment Purchaser may be or may become unable or unwilling to meet the terms specified, Company may require satisfactory assurances or full or partial payment as a condition to commencing or continuing manufacture or making shipment; and may, if shipment has been made, recover the product(s) from the carrier, pending receipt of such assurances. TAXES - Any applicable duties or sales, use, excise, value added or similar taxes will be added to the price and invoiced separately (unless acceptable exemption certificate is furnished). LIMITATION OF LIABILITY - Neither Company nor its suppliers shall be liable, whether in contract or in tort or under any other legal theory, for loss of use, revenue or profit, or for cost of capital or of substitute use or performance, or for incidental, indirect, or special or consequential damages, or for any other loss or cost of similar type, or for claims by Purchaser for damages of Purchaser s customers. Likewise, Company shall not, under any circumstances, be liable for the fault, negligence, or wrongful acts of Purchaser or Purchaser s employees, or Purchaser s other contractors of suppliers. IN NO EVENT SHALL COMPANY BE LIABLE IN EXCESS OF THE SALES PRICE OF THE PART(S) OR PRODUCT FOUND DEFECTIVE. GENERAL - (a) Company will comply with all laws applicable to Company. Compliance with OSHA or similar federal, state or local laws during any operation or use of the product(s) is the sole responsibility of Purchaser. (b) The laws of the State of New York shall govern the validity, interpretation and enforcement of any contract of which these provisions are a part, without giving effect to any rules governing the conflict of laws. (c) This document and any other documents specifically referred to as being a part hereof, constitute the entire contract on the subject matter, and it shall not be modified except in writing signed by both parties. Unless otherwise specified, any reference to Purchaser s order is for identification only. Assignment may be made only with written consent of both parties. ACCEPTANCE - The determination of compliance with performance guarantees will be based on results of factory tests under controlled conditions with calibrated instruments and tested per standards of the Hydraulic Institute. INSPECTIONS/EXPEDITING - The Company wishes to clarify that it will have to restrict access to agreed upon reasonable times and only for the purpose of conducting those inspections agreed upon. We request 72 hours notice prior to each visit. We request notification prior to visits to our subcontractors. PRICES - The prices stated herein will remain firm for the period up to the stated date of shipment providing the shipment is not delayed by the customer. If shipment is delayed by the customer beyond the shipment date quoted herein, the prices will be based on the prices in effect at time of shipment, including storage and material handling costs. In no event shall the adjusted price be less than the original order price, including change orders. Prices are F.O.B. Shipping Point, unless otherwise specified. When price includes transportation and other charges pertaining to the shipment of goods, any increase in transportation rates and other charges will be for the account of the Purchaser. There will be an extra charge for any test other than that which may be normally run by the Company, or for any test performed to suit the convenience of the Purchaser. CONTROLLING PROVISIONS - These terms and conditions shall control with respect to any purchase order or sale of the Company s products. No waiver, alteration or modification of these terms and conditions whether on Purchaser s purchase order or otherwise shall be valid unless the waiver, alteration or modification is specifically accepted in writing and signed by an authorized representative of the Company. If this transaction involves EXPORT, the following additional terms and conditions shall apply: PACKING - Equipment will be packed, boxed or crated in accordance with the Company s standard commercial practice, for underdeck export shipment, unless otherwise agreed. LETTER OF CREDIT - Unless otherwise specified in writing, payment shall be made by irrevocable letter of credit in form acceptable to Company, confirmed by a major USA bank, acceptable to the Company and providing for payment in full in United States dollars against presentation of United States inland shipping documents and invoices, such letter of credit to be established prior to Company s acceptance of the order. The letter of credit shall also provide that in the event Company is, for any reason beyond its control, prevented from making shipment from Company s factory or delivery at the port of embarkation, a certificate of manufacture of the whole or any part of the goods shall constitute delivery of such whole or any part of the goods and payment in full of any and all drafts drawn against the letter of credit for the goods so delivered shall be made upon presentation of such certificates of manufacture in lieu of United States inland shipping documents. In the event that Company is prevented by law, or otherwise, from making shipment from Company s factory or delivery at port of embarkation of the goods or any part thereof, on completion of manufacture, Company reserves the right to place the goods in storage for the Purchaser s account and risk. Any charges incurred in this connection will be for the account of the Purchaser at cost and will be payable upon demand. COMPANY AS AGENT - If Company makes or arranges for ocean shipment, Company shall act as agent for the Purchaser and reserves the right to procure full insurance coverage, including war risk insurance, at the expense of the Purchaser. All expenses incurred in this connection will be payable upon demand to the Company. If Company as agent applies for or secures manufacturing, financing, exporting or other licenses required by the United States Government, or any department thereof, Company shall make such applications or secure such licenses solely as agent for the Purchaser, and assumes no responsibility therefore TERMS OF PAYMENT - Unless otherwise stated all payments shall be Net Thirty (30) Days and in United States dollars, and a pro rata payment shall become due as each shipment is Page 2 of 2

56 Submittal Review Form Project Name: TMWA ArrowCreek Drought Response Design Proj Contract No: Submittal No: 1-R1 Resubmittal Received Submittal Title: Bid Item No.: Booster Pump Submittal Package Spec. No: 11300, Contractor/Subcontractor CH Spencer Routing Sequence Date Received Checked By Date Sent Orig. Number of Copies Prints Samples Mfg.Lit. CH Spencer 8/7/2015 Danny Beck 8/7/2015 TMWA 8/7/2015 Scott Estes 8/7/2015 Stantec Consulting Ltd. 8/7/2015 David Diegle 8/7/2015 TMWA 8/7/2015 Scott Estes CH Spencer Submittal Compliance We have verified that the material or equipment contained in this submittal meets all the requirements specified or shown (no exceptions). We have verified that the material or equipment contained in this submittal meets all the requirements specified or shown, except for the following deviations (list deviations, attach separate sheet if necessary) Contractor Remarks Submittal Status A - NO EXCEPTION NOTED (Confirm) B - NOTE MARKINGS (Confirm) C - NOTE MARKINGS (Resubmit) D - REJECTED (Resubmit) E - UNREVIEWED / INFORMATION ON Engineer Remarks 1. Pump Discharge to the control valve will be tested to 400 PSI, please make sure the pump pitless can will handle this pressure. GC Representative: Danny Beck Designer: David Diegle cc: File, Ray Stantec Consulting Services Inc. Stantec Consulting Services Inc.

57 C.H. Spencer & Company 1075 South Pioneer Road Salt Lake City, UT Phone: x.110 Fax: To: Truckee Meadows Water Authority Attn: Scott Estes Date: August 7, 2015 Reference: TMWA Project No Bid Date: July 23, 2015 Scott: Please see attached Submittal Package B for the Booster Pump on the TMWA Pumps, Motors and Pitless Adapters for Arrowcreek Drought Response Project ENGINEERS COMMENTS: 1) Pump Bowls were quoted with and will be supplied with coating per Section 2.2A 2) Pumps will be provided with SS Suction Screens 3) Motors will be provided with standard cable length, there should be roughly an additional 3-4 spare ft at the top of the adapter. 4) Pump Bowls were quoted with and will be supplied with coating per 2.2A. 5) Revised drawing attached showing 24 dimensions. 6) Revised drawing attached showing 150 lb suction flange. 7) Revised drawing showing testing that will be performed at the factory per Section :A. 8) Pump Can will be coated per Section :B, see attached data sheet and drawing. Let me know if you have any questions. Thanks Daniel Beck C.H. Spencer Sales Engineer Page 1 of 3

58

59 RustNot HEAVY INDUSTRIAL COATING PROTECTION RUSTNOT TankLine 253i PW Excellent Chemical Resistance to a Broad Range of Chemicals

60 - RustNot TankLine 253i PW PRODUCT DESCRIPTION HD HD HD5125 White Beige Hardener A two-component, high solids epoxy phenolic novolac system formulated as an internal tank lining for potable water applications and as a coating for resistance to a wide range of chemicals and solvents. Offers excellent adhesion and corrosion resistance. VOC compliant (less than 190 g/l). Also suitable for secondary containment uses and for highly corrosive applications. FEATURES High solids, low VOC Excellent adhesion to metal and concrete Excellent corrosion resistance Excellent solvent resistance RECOMMENDED USES Internal lining for chemical tanks, petroleum tanks and drilling water tanks Potable water tank lining Marine Secondary containment Hardener...HD5125 Recommended Thickness mils/coat (dry) 8-10 mils/coat (wet) Number of Coats...1 or 2 (Use a stripe coat on difficult to paint areas, such as welds, pits, edges, cutouts, brackets, etc.) Theoretical Coverage...1,235 sf/gal at 1 mil DFT Pot 77 F...6 hours Cure to Immersion Service 77 F and 50% R.H days Dry 77 F and 50% R.H. Touch Dry...4 hours Recoat...10 hours Max. Recoat...5 days Mixing...Power stir the base and hardener, then add hardener to the base and stir 5-10 minutes. Induction Time...15 minutes The above product and application data for this technical data sheet are based on product HD White. PRODUCT DATA Description Results Vehicle Type...Epoxy / Phenolic Novolac Color...White and Beige VOC (mixed w/hd5125)...<230 g/l (1.89 lbs/gal) Weight/Gallon pounds Solids by Volume (mixed)...77+/-2% Packaging...5 Gallon Kits APPLICATION DATA Description Results Application...Spray, Brush or Roll Mix Ratio...1 unit of Part B to 5gl pail of Part A. EQUIPMENT RECOMMENDATIONS Listed below are general equipment guidelines for the application of this product. Job site conditions may require modifications to these guidelines to achieve the desired results. Ensure brush and roller is well loaded to avoid air entrapment. Multiple coats may be needed to achieve adequate film build. BRUSH: Use a good quality solvent resistant, natural or synthetic. ROLLER: Use a good quality natural or synthetic 3/8 short-nap roller cover with phenolic core.

61 - RustNot TankLine 253i PW DIRECTIONS FOR USE SPRAY APPLICATION (General): The following spray equipment has been found suitable and is available from manufacturers such as Binks, DeVilbiss and Graco. AIR ATOMIZED SPRAY: Model Air Cap Fluid Head Fluid Delivery Atomizing Pressure Binks PB oz/min psi DeVilbiss MBC-510 AIRLESS SPRAY: MB HD AV-650-AC 20 oz/min psi Model Pump Ratio Fluid Tip Fluid Pressure Filter Mesh Graco 30:1 or Larger ,800-2, mesh GENERAL SURFACE PREPARATION TINTING: Do not tint. THINNING: Brush or Roll - None needed Spray - Not recommended Note: Always know local VOC restrictions for coatings applications in your area before thinning this product. Thinning recommendations meet Federal VOC restrictions for architectural coatings. This product and other referenced products may not meet VOC restrictions for your application and may not be available in your area. Carefully read and observe warning thinner labels. All surfaces must be sound, dry, clean and free of oil, dirt, grease, wax, mildew, loose or flaking paint and other surface contaminants. Remove loose, peeling, flaking or scaling paint by scraping, sanding or wire brush. Area should be sheltered from airborne particulates and pollutants. Avoid combustion gases or other sources of carbon dioxide that may promote amine blush. Ensure good ventilation during application and curing. Provide shelter to prevent wind from affecting spray patterns. For tank lining, dehumidification equipment is recommended. Surface temperature must remain at least 5 F above dew point temperature. For good results, an SSPC-SP 5 (NACE No. 1) white metal blast or SSPC-SP 10 (NACE No. 2) near-white metal blast is recommended. For moderate exposure (non-immersion), an SSPC-SP 6 (NACE No. 3) commercial blast should be used.

62 - RustNot TankLine 253i PW APPLICATION: Apply by spray, brush or roller. APPLY ONLY when air and surface temperatures are between F and the surface temperature is at least 5 F above the dew point temperature. DRYING TIME: Under normal conditions, dries to touch in 4 hours and to recoat in 8 hours. Low temperature, high humidity, poor ventilation and thick films will retard drying. CLEAN UP: Clean up skin, clothing, paint tools or spills immediately with recommended thinner, carefully observing cautions on paint and thinner labels. Dried paint may be removed by scraping. Clean Up with or Thinner, MEK or Xylene HEALTH AND SAFETY Read the Material Safety Data Sheet (MSDS) and container labels for detailed health and safety information. This product is intended for industrial use by properly trained professional applicators only. DISCLAIMER Manufacturer warrants that the physical properties of the product reported above will meet the standards and deviations of the associated ASTM test method. MANUFACTURER HEREBY EXPRESSLY DISCLAIMS ANY AND ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTY OF MERCHANTABILITY AND/OR IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Buyer must make its own determination of the suitability of any product for its use, whether such product is used alone or in combination with other materials. To the extent this or any of Manufacturer s products is proven to be defective, Buyer s sole remedy shall be limited to the replacement of such defective product, exclusive of any costs of labor. MANUFACTURER SHALL NOT BE LIABLE OR OBLIGATED FOR ANY LOSS OR CONSEQUENTIAL OR OTHER DAMAGE INCURRED DIRECTLY OR INDIRECTLY BY BUYER OR ANY OTHER PERSON OR ENTITY THAT ARISES IN ANY WAY IN RELATION TO THIS OR ANY OF MANUFACTURER S OTHER PRODUCTS. Nothing contained herein shall be construed to constitute inducement or recommendation to practice any invention covered by any patent without authority of the owner of the patent. No Applicator is or should be viewed as an employee or agent of Manufacturer. Robert Claybaker Cell JONES-BLAIR /NEOGARD

63 Terms & Conditions General Provisions WARRANTY - Company warrants title to the product(s) and, except as noted with respect to items not of Company s manufacturer, also warrants the product(s) on date of shipment to Purchaser, to be of the kind and quality described herein, and free of defects in workmanship and material. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS, AND CONSTITUTES THE ONLY WARRANTY OF COMPANY WITH RESPECT TO THE PRODUCT(S). If within one year from date of initial operation, but not more than eighteen months from date of shipment by Company of any item of product(s), Purchaser discovers that such item was not as warranted above and promptly notifies Company in writing thereof, Company shall remedy such nonconformance by, at Company s option, adjustment or repair or replacement of the item and any affected part of the product(s). Purchaser shall assume all responsibility and expense for removal, reinstallation, and freight in connection with the foregoing remedies. The same obligations and conditions shall extend to replacement parts furnished by Company hereunder. Company shall have the right of disposal of parts replaced by it. Purchaser agrees to notify Company, in writing, of any apparent defects in design, material or workmanship, prior to performing any corrective action back chargeable to the Company. Purchaser shall provide a detailed estimate of the material, labor costs associated with proposed remedy for expeditious review and approval by the Company. ANY SEPARATELY LISTED ITEM OF THE PRODUCT(S) WHICH IS NOT MANUFACTURED BY THE COMPANY IS NOT WARRANTED BY COMPANY and shall be covered only by the express warranty, if any, of the manufacturer thereof. THIS STATES PURCHASER S EXCLUSIVE REMEDY AGAINST COMPANY AND ITS SUPPLIERS RELATING TO THE PRODUCT(S) WHETHER IN CONTRACT OR IN TORT OR UNDER ANY OTHER LEGAL THEORY, AND WHETHER ARISING OUT OF WARRANTIES, REPRESENTATIONS, INSTRUCTIONS, INSTALLATIONS OR DEFECTS FROM ANY CAUSE. Company and its suppliers shall have no obligation as to any product which has been improperly stored or handled, or which has not been operated or maintained according to instructions in Company or supplier furnished manuals. PATENTS - Company shall pay costs and damages finally awarded in any suit against Purchaser or its vendees to the extent based upon a finding that the design or construction of the product(s) as furnished infringes a United States patent (except infringement occurring as a result of incorporating a design or modification at Purchaser s request) provided that Purchaser promptly notifies Company of any change of such infringement, and Company is given the right at its expense to settle such charge and to defend or control the defense of any suit based upon such charge. THIS PARAGRAPH SETS FORTH COMPANY S EXCLUSIVE LIABILITY WITH RESPECT TO PATENTS. BUYER DATA - Timely performance is contingent upon the Purchaser supplying to the Company, when needed, all required technical information, including drawing approval, and all required commercial documentation. NUCLEAR - Purchaser represents and warrants that the product(s) covered by this contract shall not be used in or in connection with a nuclear facility or application. NONCANCELLATION - Purchaser may not cancel or terminate for convenience, or direct suspension of manufacture, except on mutually acceptable terms. DELAYS - If Company suffers delay in performance due to any cause beyond its control, including but not limited to act of God, war, act or failure to act of government, act or omission of Purchaser, fire flood, strike or labor troubles, sabotage, or delay in obtaining from others suitable services, materials, components, equipment or transportation, the time of performance shall be extended a period of time equal to the period of the delay and its consequences. Company will give to Purchaser notice in writing within a reasonable time after Company becomes aware of any such delay. STORAGE - Any item of the product(s) on which manufacture or shipment is delayed by causes within Purchaser s control, or by causes which affect Purchaser s ability to receive the product(s), may be placed in storage by Company for Purchaser s account and risk. SHIPMENT - The term shipment means delivery to the initial carrier in accordance with the delivery terms of this order. Company may make partial shipments. Company shall select method of transportation and route, unless terms are f.o.b. point of shipment and Purchaser specifies the method and route and is to pay the freight costs in addition to the price. When terms are f.o.b. destination or freight allowed to destination, destination means common carrier delivery point (within the continental United States, excluding Alaska) nearest the destination. For movement outside the United States, Company shall arrange for inland carriage to port of exit and shall cooperate with Purchaser s agents in making necessary arrangements for overseas carriage and preparing necessary documents. SPECIAL SHIPPING DEVICES - On shipments to a destination in the continental United States or Canada, Company has the right to add to the invoice, as a separate item, the value of any special shipping device (barrel, reel, tarpaulin, cradle, crib and the like) used to contain or protect the product(s) invoiced, while in transit. Full credit will be given on the return to Company of the device in a reusable condition, f.o.b. destination, freight prepaid. TITLE AND INSURANCE - Title to the product(s) and risk of loss or damage shall pass to Purchaser at the f.o.b. point, except that a security interest in the product(s) and proceeds and any replacement shall remain in Company, regardless of mode of attachment to realty or other property, until the full price has been paid in cash. Purchaser agrees to do all acts necessary to perfect and maintain said security interest, and to protect Company's interest by adequately insuring the product(s) against loss or damage from any external cause with Company named as insured or co-insured. made. If shipment is delayed by Purchaser, date of readiness for shipment shall be deemed to be date of shipment for payment purposes. If at any time in Company s judgment Purchaser may be or may become unable or unwilling to meet the terms specified, Company may require satisfactory assurances or full or partial payment as a condition to commencing or continuing manufacture or making shipment; and may, if shipment has been made, recover the product(s) from the carrier, pending receipt of such assurances. TAXES - Any applicable duties or sales, use, excise, value added or similar taxes will be added to the price and invoiced separately (unless acceptable exemption certificate is furnished). LIMITATION OF LIABILITY - Neither Company nor its suppliers shall be liable, whether in contract or in tort or under any other legal theory, for loss of use, revenue or profit, or for cost of capital or of substitute use or performance, or for incidental, indirect, or special or consequential damages, or for any other loss or cost of similar type, or for claims by Purchaser for damages of Purchaser s customers. Likewise, Company shall not, under any circumstances, be liable for the fault, negligence, or wrongful acts of Purchaser or Purchaser s employees, or Purchaser s other contractors of suppliers. IN NO EVENT SHALL COMPANY BE LIABLE IN EXCESS OF THE SALES PRICE OF THE PART(S) OR PRODUCT FOUND DEFECTIVE. GENERAL - (a) Company will comply with all laws applicable to Company. Compliance with OSHA or similar federal, state or local laws during any operation or use of the product(s) is the sole responsibility of Purchaser. (b) The laws of the State of New York shall govern the validity, interpretation and enforcement of any contract of which these provisions are a part, without giving effect to any rules governing the conflict of laws. (c) This document and any other documents specifically referred to as being a part hereof, constitute the entire contract on the subject matter, and it shall not be modified except in writing signed by both parties. Unless otherwise specified, any reference to Purchaser s order is for identification only. Assignment may be made only with written consent of both parties. ACCEPTANCE - The determination of compliance with performance guarantees will be based on results of factory tests under controlled conditions with calibrated instruments and tested per standards of the Hydraulic Institute. INSPECTIONS/EXPEDITING - The Company wishes to clarify that it will have to restrict access to agreed upon reasonable times and only for the purpose of conducting those inspections agreed upon. We request 72 hours notice prior to each visit. We request notification prior to visits to our subcontractors. PRICES - The prices stated herein will remain firm for the period up to the stated date of shipment providing the shipment is not delayed by the customer. If shipment is delayed by the customer beyond the shipment date quoted herein, the prices will be based on the prices in effect at time of shipment, including storage and material handling costs. In no event shall the adjusted price be less than the original order price, including change orders. Prices are F.O.B. Shipping Point, unless otherwise specified. When price includes transportation and other charges pertaining to the shipment of goods, any increase in transportation rates and other charges will be for the account of the Purchaser. There will be an extra charge for any test other than that which may be normally run by the Company, or for any test performed to suit the convenience of the Purchaser. CONTROLLING PROVISIONS - These terms and conditions shall control with respect to any purchase order or sale of the Company s products. No waiver, alteration or modification of these terms and conditions whether on Purchaser s purchase order or otherwise shall be valid unless the waiver, alteration or modification is specifically accepted in writing and signed by an authorized representative of the Company. If this transaction involves EXPORT, the following additional terms and conditions shall apply: PACKING - Equipment will be packed, boxed or crated in accordance with the Company s standard commercial practice, for underdeck export shipment, unless otherwise agreed. LETTER OF CREDIT - Unless otherwise specified in writing, payment shall be made by irrevocable letter of credit in form acceptable to Company, confirmed by a major USA bank, acceptable to the Company and providing for payment in full in United States dollars against presentation of United States inland shipping documents and invoices, such letter of credit to be established prior to Company s acceptance of the order. The letter of credit shall also provide that in the event Company is, for any reason beyond its control, prevented from making shipment from Company s factory or delivery at the port of embarkation, a certificate of manufacture of the whole or any part of the goods shall constitute delivery of such whole or any part of the goods and payment in full of any and all drafts drawn against the letter of credit for the goods so delivered shall be made upon presentation of such certificates of manufacture in lieu of United States inland shipping documents. In the event that Company is prevented by law, or otherwise, from making shipment from Company s factory or delivery at port of embarkation of the goods or any part thereof, on completion of manufacture, Company reserves the right to place the goods in storage for the Purchaser s account and risk. Any charges incurred in this connection will be for the account of the Purchaser at cost and will be payable upon demand. COMPANY AS AGENT - If Company makes or arranges for ocean shipment, Company shall act as agent for the Purchaser and reserves the right to procure full insurance coverage, including war risk insurance, at the expense of the Purchaser. All expenses incurred in this connection will be payable upon demand to the Company. If Company as agent applies for or secures manufacturing, financing, exporting or other licenses required by the United States Government, or any department thereof, Company shall make such applications or secure such licenses solely as agent for the Purchaser, and assumes no responsibility therefore TERMS OF PAYMENT - Unless otherwise stated all payments shall be Net Thirty (30) Days and in United States dollars, and a pro rata payment shall become due as each shipment is Page 2 of 2

64 C.H. Spencer & Company 1075 South Pioneer Road Salt Lake City, UT Phone: x.110 Fax: To: TMWA Attn: Scott Estes Date: August 25, 2015 Reference: Bladder Type Hydro Pneumatic Tanks for the Arrow Creek Drought Response Project. Bid Date: Enter Date Scott: Below is a Submittal Package for the Hydro Pneumatic Tanks for the Arrow Creek Drought Response Project. I: EQUIPMENT DESCRIPTION: Zolezzi Booster Pump Station Quantity (1) SSA Hydro -Pressure Rating of 350 PSI -ID Coating with NSF 61 and 372 Certified Coating. -Seismic Cals stamped by a NV Engineer Arrow Creek Booster Pump Station Quantity (1) SSA Hydro -Pressure Rating of 250 PSI -ID Coating with NSF 61 and 372 Certified Coating. -Seismic Calcs stamped by a NV Engineer Accessories that will be provided loose: - (2) ½ inch ball valves rated for 600 psi, NSF 61 compliant. - (2) ½ Safety Relief Valves *Please note that the seismic calculations will be provided 2-4 weeks after engineer s approval. As Built Drawings will be provided 2-4 weeks after engineer s approval. Very truly yours, Daniel Beck Sales Engineer C.H. Spencer & Company Page 1 of 3

65 SUBMITTAL AAtanks TYPE: ASME SHOCK ARRESTORS MODELS: SSA Submittal Sheet No. B-3806 Date: 4-03 JOB Aarow Creek Pump Station Unit Tag No. Engineer STANTEC ENGINEERING Contractor TRUCKEE MEADOWS DESCRIPTION AAtanks Type SSA Tank is an ASME replaceable bladder type pre-charge hydro-pneumatic tanks for commercial and industrial, municipal, and well water systems, to effectively control water hammer shock, and pump start-up/shut-down water surge. The vessel is fabricated to 275 psi rating with large water system connection designed to accept potentially harmful water surge pressures quickly, with minimal pressure drop. AAtanks Representative C.H. SPENCER & COMPANY Order No. Date Submitted By Daniel Beck Date 08/26/15 Approved By Date CONSTRUCTION Shell: Carbon Steel Bladder: Heavy Duty Butyl External Finish: Red Epoxy Primer 2-3 mills Internal Finish: NSF 61 /NSF 372 Coating System PERFORMANCE LIMITATIONS Maximum Design Temperature: 240ºF Maximum Design Pressure: 275 PSI Factory pre-charge: 10 PSI (Field Adjustable) CAPACITY DIA HT SYS WEIGHT MODEL (GAL.) (IN.) (IN.) (IN.) 275 PSI 500 PSI SSA TYPICAL SPECIFICATION Furnish and install on the plans a 250 gallon 36 diameter X 85 (high) pre-charged steel hydro-pneumatic tank with 8 diameter system connection and replaceable heavy-duty butyl bladder. The interior shall be properly prepared sand blasted to white metal prior and shall be epoxy-lined with a NSF 372/NSF 61 coating. The tank shall have a bottom flanged system connection, a ¼ pressure gauge tapping, and a charging valve connection (standard tire valve) to facilitate the onsite charging of the tank to meet system requirements. The tank shall be fitted with lifting rings and a floor mounting legs for vertical installation. The tank must be constructed in accordance with Section VIII of the ASME Boiler and Pressure Vessel Code and stamped PSI working pressure Sherwood Center Line, MI (586) (586) FAX

66 SUBMITTAL AAtanks TYPE: ASME SHOCK ARRESTORS MODELS: SSA Submittal Sheet No. B-3806 Date: 4-03 JOB Zolezzi Booster Pump Statoion Unit Tag No. Engineer STANTEC ENGINEERING Contractor TRUCKEE MEADOWS DESCRIPTION AAtanks Type SSA Tank is an ASME replaceable bladder type pre-charge hydro-pneumatic tanks for commercial and industrial, municipal, and well water systems, to effectively control water hammer shock, and pump start-up/shut-down water surge. The vessel is fabricated to 500 PSI rating with large water system connection designed to accept potentially harmful water surge pressures quickly, with minimal pressure drop. AAtanks Representative C.H. SPENCER & COMPANY Order No. Date Submitted By Daniel Beck Date 08/26/15 Approved By Date CONSTRUCTION Shell: Carbon Steel Bladder: Heavy Duty Butyl External Finish: Red Epoxy Primer 2-3 mills Internal Finish: NSF 61/ NSF 372 Coating System PERFORMANCE LIMITATIONS Maximum Design Temperature: 240ºF Maximum Design Pressure: 500 PSI Factory pre-charge: 10 PSI (Field Adjustable) CAPACITY DIA HT SYS WEIGHT MODEL (GAL.) (IN.) (IN.) (IN.) 275 PSI 500 PSI SSA inch 300 # Suction/Discharge Flange. 16 inch Top Flange Seismic Analysis Report (To be provided 2-4 weeks after engineers approval) Specific Dimensional Drawings will be provided 2-4 weeks after engineers approval. TYPICAL SPECIFICATION Furnish and install on the plans a 250 gallon 36 diameter X 85 (high) pre-charged steel hydro-pneumatic tank with 8 diameter system connection and replaceable heavy-duty butyl bladder. The interior shall be properly prepared sand blasted to white metal prior and shall be epoxy-lined with a Tnemec Plastite #7156 two-part epoxy coating. The tank shall have a bottom flanged system connection, a ¼ pressure gauge tapping, and a charging valve connection (standard tire valve) to facilitate the on-site charging of the tank to meet system requirements. The tank shall be fitted with lifting rings and a floor mounting legs for vertical installation. The tank must be constructed in accordance with Section VIII of the ASME Boiler and Pressure Vessel Code and stamped PSI working pressure Sherwood Center Line, MI (586) (586) FAX

67 !"#$%& $ $'! ( $ ) $ * ' "!

68 !"!#!$% "&'( -''"!.( "!")!/#01"2$-341 &"# '!"#$ % "! ()*+** $ )*+*, #$% &'$(#)*+,-,. +$/,,.".0 )%/,,.0. -0"+(121(13 #)42315)(1$ ))6)# +$/,.-.,- )%/,.-. =9.>(161 '*1?1*)1$22;@A*$*+)8&1+$;$1* )82 9. $4): );2)5&1<()6 +$/..-.. )%/..-.. &&&*).3)*$4 &'

69 WQA Goldseal Certified Products Page 1 of 3 10/8/2014 Water Quality Association 10/08/2014 CERTIFIED LEAD FREE PRODUCTS NSF/ANSI 372: Drinking Water System Components - Lead Content Certification to NSF/ANSI 372 (Previously, WQA's Other Recognized Document (ORD), ORD0902), was established by WQA to compile the minimum requirements for the evaluation of lead content in drinking water products, material, and components for compliance to laws, regulations, or other restrictions for lead content. NSF/ANSI 372 combines the lead content calculations from NSF/ANSI 61 - Annex G and the testing protocol established by the California Department of Toxic Substances. Certification to NSF/ANSI 372 demonstrates compliance to the following: California Health and Safety Code Section definition of lead free (A.K.A. NSF/ANSI 61 Annex G, AB 1953), and Vermont s lead in consumer products law, 9 V.S.A., Chapter 63, Subchapter 1C, and Any other law, regulation, or restriction on lead content that may use the same calculations and testing protocol to demonstrate lead free compliance. CLA-VAL 1701 Placentia Ave Costa Mesa, CA Phone: (949) Product Type: Component Brand Name Model 100-YY models 1 12X-YY/62X-YY models YY/631-YY models YY/633-YY models YY/636-YY models YY/610-YY models 6 4X-YY/64X-YY models 7 5X-YY/65X-YY models 8 6X-YY/66X-YY models 9 7XX-YY models YY/681-YY models 11 9X-YY/69X-YY models 12

70 WQA Goldseal Certified Products Page 2 of 3 10/8/2014 Air and Vacuum Valve (1/2" to 20") Series 35, 37, TD Air Release Valve (1/2" to 6") Series 34 Arrestor Check (3" to 16") Series AC Combination Air Valve (1" to 8") Series 36 Flex-Check Valve (2" to 42") Silent Globe Check Valve (2.5" to 42") Series 581 Silent Wafer Check Valve (2" to 10") Series 580 Swing Check Valve (2" - 48") Tite Seal Foot Valve (2" to 36") Series 583 Two-Door Check Valve (2" to 66") Vacuum Breaker (3" to 16') 1: 100-YY includes models ,100-02,100-03, and Series 584 (Optional RFA) Series 585 (LW, AC, LS) Series 582, 582G, 582L, 582W Series 38VB 2: 12X-YY includes models , and ; 62X-YY includes , and ; / also fall in this family 3: 131-YY Include , , , , ,131-08, and ; 631-YY Include , , , , , , and : 133-YY includes and ; 633-YY includes and : 136-YY Include and ; 636-YY Include and : 210-YY Include , , and ; 610-YY Include , , and : 4X-YY includes models 40-01, and 49-01; 64X-YY includes , and : 5X-YY Include models 50-01, and 58-01; 65X -YY includes models , and ; and 605/01 also fall in this family; the CRL and the 55 F are Controls and are part of the 50 series 9: 6X-YY include 60-11, 60-19, and 61-02; 66X-YY include , , and : 7XX-YY include , , , and : 81-YY includes and 81-02; 681-YY includes and : 9X-YY includes 90-01, 90-48, 92-01, and 90-11; 69X-YY includes , , , and ; also falls in this family Disclaimer: The information in the Water Quality Association product listings directory is made available by WQA for users of this website and shows currently certified products. Every effort has been made to verify the accuracy of all listings in this directory. The association can assume no liability for errors or omissions. Water Quality Association: Wed, Oct 8, 2014 Back Copyright 2014 by the Water Quality Association All rights reserved. Water Quality Association International Headquarters & Laboratory 4151 Naperville Road Lisle, IL USA , Fax info@wqa.org,

71 Series SC201 2-Piece 316 Stainless Ball Valve E 1000# CWP, 150# WSP Full Port Blow-Out Proof Stem Vacuum Service to 29 Hg Locking Handle ISO 9001:2008 Manufacturer MSS SP-10 Lead Free P R ES S U RE P SI PRESSURE - TEMPERATURE RATING No. Part Material 1 Handle Sleeve Plastic 2 Body ASTM A351 GR CF8M ( SS316) 3 Seat RTFE 15% 4 Ball ASTM A351 GR CF8M ( SS316) 5 End Cap CF8M Stainless Steel (316) 6 Body Seal PTFE 7 Thrust Washer PTFE 8 Stem Packing PTFE 9 Packing Nut 304 Stainless Steel 10 Handle Washer 304 Stainless Steel 11 Handle Nut 304 Stainless Steel 12 Stem ASTM A276 T Locking Device 304 Stainless Steel 14 Handle 304 Stainless Steel TEMPERATURE USA Fax Los Angeles, CA Chicago, IL Atlanta, GA Vancouver, WA Houston, TX Size Weight d L H E Part Number IN LB IN IN IN IN 1/4 SC201C /8 SC201E /2 SC201G /4 SC201I SC201K /4 SC201L /2 SC201M SC201N /2 SC201P SC201Q Rev.9/16/13

72 August 18, 2015 Quote S Truckee Meadows Water Authority Scott Estes P.O. Box Reno, NV Dear Scott: Per your request please see below our proposal for the electrical equipment for the Arrowcreek project. If you have any questions or require any additional information, please don t hesitate to ask. Thank you for considering the George T. Hall Company. Zolezzi Lane BPS 1200A SWBD UL891 Nema 3R (White Finish) 1200A 480/277V 3Ø 4W 65Kaic 1,000SQ-Inch COPPER A U.G/CT Compt (Utility) A Main/Gen Compt A/3P MCCB TM trip (Main) 1 Rotary Door Handle 1 400A/3P MCCB TM trip (Gen.) 1 Rotary Door Handle 2 Key Interlock 1 Phase monitoring relay 1 Power Monitor 3 CT's 1200:5A 3 PT's V 1 SPD 320kA 1 60A/3P MCCB TM trip (SPD) 1 225A MLO panelboard "LP" -20/208V 3P4W AL 10kAIC UL 67 NEMA A/1P TM branch breaker 1 XMFR 30KVA /208V 1 50A/3P MCCB TM trip (XFMR) 1 400A/3P MCCB TM trip (Pump Station) 1 Booster Pump A sect 1 250A/3P MCCB TM trip (Pump-A) 1 SSRV/Contactors 100HP 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor (By others) 3 CT's 250:5A 3 PT's V 1 EMT 1 Delay relay 1 Power Fail Relay 1 Booster Pump B sect 1 250A/3P MCCB TM trip (Pump-B) 1 SSRV/Contactors 100HP 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor 3 CT's 250:5A 3 PT's V 1 EMT 1 Delay relay 1 Power Fail Relay MISC. 3 Door Switch 1 Receptacle 1 Mech Timer 3 LED light 3 Space Heater 1 Thermostat 1 Spare Fuses-Lights 3 Sunshield White finish 1 Pressure type lugs

73 Arrowcreek BPS 1200A SWBD UL891 Nema 3R (White Finish) 1200A 480/277V 3Ø 4W 65Kaic 1,000SQ-Inch COPPER A U.G/CT Compt (Utility) A Main/Gen Compt A/3P MCCB TM trip (Main) 1 Rotary Door Handle 1 400A/3P MCCB TM trip (Gen.) 1 Rotary Door Handle 2 Key Interlock 1 Phase monitoring relay 1 Power Monitor 3 CT's 1200:5A 3 PT's V 1 SPD 320kA 1 60A/3P MCCB TM trip (SPD) 1 225A MLO panelboard "LP" -20/208V 3P4W AL 10kAIC UL 67 NEMA A/1P TM branch breaker 1 XMFR 30KVA /208V 1 50A/3P MCCB TM trip (XFMR) 1 400A/3P MCCB TM trip (Pump Station) 1 Booster Pump A sect 1 175A/3P MCCB TM trip (Pump-A) 1 SSRV/Contactors 100HP 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor (By others) 3 CT's 250:5A 3 PT's V 1 EMT 1 Delay relay 1 Power Fail Relay 1 Booster Pump B sect 1 175A/3P MCCB TM trip (Pump-B) 1 SSRV/Contactors 100HP 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor 3 CT's 250:5A 3 PT's V 1 EMT 1 Delay relay 1 Power Fail Relay MISC. 3 Door Switch 1 Receptacle 1 Mech Timer 3 LED light 3 Space Heater 1 Thermostat 1 Spare Fuses-Lights 3 Sunshield White finish 1 Pressure type lugs

74 400A SWBD UL891 Nema 3R (White Finish) 400A 480/277V 3Ø 4W 65Kaic 1,000SQ-Inch COPPER 1 400A U.G/CT Compt (Utility) 1 400A Main/Gen Compt A/3P MCCB TM trip (Main) 1 Rotary Door Handle 1 400A/3P MCCB TM trip (Gen.) 1 Rotary Door Handle 2 Key Interlock 1 Phase monitoring relay 1 Power Monitor 3 CT's 1200:5A 3 PT's V 1 SPD 320kA 1 60A/3P MCCB TM trip (SPD) 1 225A MLO panelboard "LP" -20/208V 3P4W AL 10kAIC UL 67 NEMA A/1P TM branch breaker 1 XMFR 30KVA /208V 1 50A/3P MCCB TM trip (XFMR) 1 Booster Pump A sect 1 175A/3P MCCB TM trip (Pump-A) 1 SSRV/Contactors 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor (By others) 3 CT's 250:5A PT's V 1 EMT 1 Delay relay 1 Power Fail Relay 1 Booster Pump B sect 1 175A/3P MCCB TM trip (Pump-B) 1 SSRV/Contactors 1 HOA Switch 2 Pilot Lights 2 Control Relay 1 CPT 150VA 1 Push Button 1 Power Monitor 3 CT's 250:5A 3 PT's V 1 EMT 1 Delay relay 1 Power Fail Relay 1 Control Section. Backpan MISC. 4 Door Switch 1 Receptacle 1 Mech Timer 4 LED light 4 Space Heater 1 Thermostat 1 Spare Fuses-Lights 4 Sunshield White finish

75 NOTES Gear shall be manufactured by RSE-Sierra, a Myers Power Products Company. Seismic certification, if required, shall be furnished by others. Engineered drawings shall be furnished in the time frame quoted. Short circuit/coordination and arc flash studies shall be furnished by others. Field Testing shall be furnished by others. Allowance for field service covers no more than 8 hours per day, between 7 am and 6 pm Monday through Friday, holidays excepted. Transportation, lodging and per diem, if appropriate, will be added to the invoice. Startup services shall be furnished by others. Utility CT-meter compartments include provisions for CTs and for meters. CTs and meters not listed elsewhere in this BOM shall be furnished by others. - System Inergrator not part of scope (by others.) - Seismic Calculation is not included. Myers complies with Seismic Zone 4. -Vibration isolators not included - Quoting UL891 certified Switchboard. - Quoting control components per schematic drawing E RTU/PLC not part of scope (By others.) - Exception to the AM-Meter per spec. Single line does not show the AM-Meter. - Per note 6 dwg, Power Monitor is provided by TMWA. Quoting only provisions. (By others.) -Section A-3: Across the line start FVNR is not included in this proposal. The control diagram does not show an across the line start, E However a Shorting contactor is internal to the ATS22. Quote is based on single line, E005 Energy Saver: Feature is not available in RVSS technology. It is used in VFDs. Please allow 2-3 weeks for submittals, then weeks for delivery after approval to release CLARIFICATIONS Freight included, FOB Shipping Point (Ontario, CA). Lift gate, restricted access destination, or wait time >1 hr will incur additional charge. Lead time estimate is based on material availability at time of quote and begins upon release of order. Good faith efforts will be made to deliver in the time frame quoted; in the case of unanticipated delays. Payment terms: Progress Payments per following schedule 20% Upon Submittal of Drawings for Review / Approval 30% Release for Fabrication 30% Manufacturing Complete 10% Ready for test 10% Shipment This quotation is valid until 2/30/2016 Sales tax is not included. Liftgate truck additional $75.00 Submittals and O&M Manuals shall be furnished in PDF format. Hard copies may be purchased for $250 per volume. Receipt of a purchase order serves as explicit confirmation that customer has reviewed this quote for accuracy and completeness prior to acceptance and constitutes acceptance of the quote BOM without revision. No additions or modifications may be made to this BOM after the order is accepted without commensurate price adjustment. Any deviation in quantities or part numbers listed above will be subject to a new quotation. Total for above products & services: $220,500.00

76 Notes: Sincerely, Michael Smith George T. Hall Company