No. Thickness(mm) Spec(range) Material Item Type Plating Method 1

Transcription

1 CONDUCTIVE FABRIC EMI shielding depends upon the extent of conductivity of fabric. The reduction of EMI is achieved through incidence, absorptance, multilayer reflectance and grounding when the electro-magnetic wave meets conductive fabric as shown below figure. No. Thickness(mm) Spec(range) Material Item Type Plating Method ±0.003 Woven, Ripstop SS-370-PCN 16D/Press Woven Ni+Cu+Ni 003~ ±0.003 Non-Woven SSNW-20-PCN 20g Non-woven/Press Ni+Cu+Ni ±0.01 Woven, Ripstop SWRP-370-PCN 16D/Press Woven Ni+Cu+Ni 0.04 ~ ±0.03 Non-Woven LDNW-6-PCN 6g 6g/Non-Wovern Ni+Cu+Ni ±0.01 D.T.Y WPD-300-Gold 30D/Press D.T.Y Ni+Cu+Ni+Ag 0.05~ ±0.01 D.T.Y WPD-300-PCN 30D/Press D.T.Y Ni+Cu+Ni ~ 0.065±0.01 Woven W-200-PCN 75D/Woven Ni+Cu+Ni ±0.01 Mesh SM-130-PCN 5D Ni+Cu+Ni 0.07~ ±0.01 Mesh SM-200-PCN 15D Ni+Cu+Ni ±0.0.3 Non-Woven NW-20-PCN 20g Non-woven Ni+Cu+Ni ±0.01 D.T.Y WD-300-PCN 30D/Press D.T.Y Ni+Cu+Ni ±0.01 D.T.Y WPD-260-PCN 50D/Press D.Y.Y Ni+Cu+Ni 0.08~ ± Woven W-280-PCN 50D Filla/Woven Ni+Cu+Ni ±0.01 Mesh M-130-PCN 20D Ni+Cu+Ni ±0.01 Mesh M-200-PCN 20D Ni+Cu+Ni ~ 0.095±0.01 Mesh M-80-PCN 30D Ni+Cu+Ni ±0.01 Woven W-290-PCN 50 Filla/Woven Ni+Cu+Ni ±0.03 Non-Woven LDNW-20-PCN 20g Non-Woven Ni+Cu+Ni 0.1~ ±0.01 Woven, Ripstop WR-260-PCN 50D Filla/ Rip-stop Ni+Cu+Ni ±0.01 Woven F&D-290-PCN 50D Filla + D.T.Y Ni+Cu+Ni ±0.01 Woven, Ripstop WR-290-PCN 50D Filla/3mm Rip-stop Ni+Cu+Ni ±0.01 Ripstop D.T,Y WRD-270-PCN 50D Rip-stop D.T.Y Ni+Cu+Ni 0.11~ ±0.01 Twill W-190-PCN 75D Twill Ni+Cu+Ni ± D.T.Y WD-250-PCN 50D D.T.Y Ni+Cu+Ni ±0.03 Non-Woven NW-30-PCN 30g Non-woven Ni+Cu+Ni 0.13~ ±0.01 Mesh MN-90-PCN Nobang Ni+Cu+Ni ~ 0.155±0.01 D.T.Y WD-260-PCN 75D/D.T.Y Ni+Cu+Ni ±0.01 D.T.Y WD-270-PCN 75D/150D D.T.Y Ni+Cu+Ni 0.18~ ±0.01 Woven W-130-PCN Oxford yarn Ni+Cu+Ni ~ 0.19±0.03 Non-Woven NW-50-PCN 50g Non-Woven Ni+Cu+Ni ~ 0.21±0.01 D.T.Y WD-320-PCN 150D D.T.Y Ni+Cu+Ni ±0.01 Spen Yarn WS-220-PCN Spun yarn Ni+Cu+Ni 0.23~ ±0.01 Mesh NET Ni+Cu+Ni ±0.1 Cushion TRO-0.2 Polyolefin Ni+Cu+Ni 0.25~ ± Non-Woven NW-70-PCN 70g Non-Woven Ni+Cu+Ni ±0.03 Non-Woven NW-100-PCN 100g Non-Woven Ni+Cu+Ni ±0.1 Cushion TRO MESH Cushion+Mesh Ni+Cu+Ni+Water PU 0.3~ ±0.1 Cushion TRO-0.3 Polyolefin Ni+Cu+Ni+Water PU ±0.1 Cushion XY-0.3 Polyethylene Ni+Cu+Urethane ±0.03 Non-Woven N W-K100-PCN 1100g K-type Non-woven Ni+Cu+Ni 0.4~ ±0.01 Mesh M-40-PCN Plastic mesh Ni+Cu+Ni ±0.03 Spen Yarn SPW-60-PCN Span non-woven Ni+Cu+Ni ±0.1 Cushion TRO-0.5 Polyolefin Ni+Cu+Ni+Water PU 0.5~ ±0.1 Cushion XY-0.5 Polyethylene Ni+Cu+Ni+Urethane ±0.01 Mesh MF-200-PCN French Ni+Cu+Ni ±0.1 Cushion TRO-0.7 Polyolefin Ni+Cu+Ni+Water PU ~ ±0.1 Cushion XY-0.7 Polyethylene Ni+Cu+Ni+Urethane ±0.1 Cushion TRO-0.8 Polyolefin Ni+Cu+Ni+Water PU 0.8~ ±0.1 Cushion XY-0.8 Polyethylene Ni+Cu+Ni+Urethane ±0.2 Cushion TRO-1.0 Polyolefin Ni+Cu+Ni+Water PU 1.0~ ±0.2 Cushion XY-1.0 Polyethylene Ni+Cu+Ni+Urethane

2 EMI ADHESIVE TAPE Flexibility and durability of conductive adhesive is applying to mobile phone, many small-sized electric and electronic appliances and alternating EMC and ESD. Additionally it is applied for EMI shielding of many appliances, guaranty of ground connection and grounding of shield Gasket. Conductive Tape Part Reference Aluminum Foil Tape Fabric Single Side Tape Fabric Double Side Tape Product No. Thickness Product No. Thickness Product No. Thickness IT3-T mm IT3-S mm IT3-S7050D 0.05mm IT3-T502AD 0.055mm IT3-S mm IT3-S7025D 0.05mm IT3-T501AL 0.07mm IT3-S mm IT mm IT3-T503L 0.07mm IT3-S705G 0.07mm IT3-S7080D 0.08mm IT3-T mm IT3-701P 0.11mm IT3-706D 0.10mm IT3-5112ND 0.085mm IT3-701C 0.11mm IT3-700D 0.11mm IT3-502AD 0.085mm IT mm IT3-700RD 0.11mm IT mm IT3-702G(T) 0.11mm IT3-701D 0.13mm Copper Foil Tape IT3-711HF 0.15mm IT3-702D 0.13mm Product No. Thickness IT mm IT3-7015AD 0.15mm IT3-601CP 0.065mm IT3-NC mm IT3-704AD 0.20mm IT3-601CP 0.07mm IT3-701L 0.15mm IT3-703AD 0.20mm Non-carrier Tape IT3-NC mm IT3-700MD 0.20mm Product No. Thickness IT3-703A 0.20mm IT mm IT3-N mm IT3-704A 0.20mm IT mm IT mm IT3-704M 0.30mm

3 ADHESIVE TAPE PET Acrylic Single, Double Side Part Refference PET Acrylic Double Side PET Metal Dome Switch Non-Woven Double Side Product No. Thickness Product No. Thickness Product No. Thickness IT3-DP mm IT3-RPW mm IT3-DT mm IT3-DP mm IT3-RPW mm IT3-DT mm IT3-DP mm IT3-RP mm IT3-DT mm IT3-WP mm IT3-RP mm PET Acrylic Single side IT3-DP mm IT3-RPA0207L 0.07mm Product No. Thickness IT3-DP mm PET Shading single side IT3-RP mm IT3-DP mm Product No. Thickness IT3-RP mm IT3-DP mm IT3-RP mm IT3-RP mm IT3-DP mm IT3-RP mm05mm PET Acrylic / Silicone PET Shading Double Side PET Acrylic Single side Product No. Thickness Product No. Thickness Product No. Thickness IT3-WP mm IT3-DP mm IT3-RP mm IT3-WP mm IT3-DP mm IT3-RP mm IT3-WP mm IT3-DP mm PET Acrylic Removal IT3-WP mm IT3-DP mm Product No. Thickness IT3-WP mm PET Silicone IT3-RP mm IT3-WP mm Product No. Thickness IT3-RP mm IT3-WP mm IT3-RP mm IT3-RPG mm IT3-WP mm IT3-RP mm IT3-RP mm IT3-RP mm

4 Ni-Co CONDUCTIVE TAPE (IT3-NC100S/ NC050S) Fabric Structure Composition Conductive fabric (Ni-Co Alloying) Adhesive Release Liner It has known that the general electromagnetic waves shielding fabric in present has been plated by Cu+Ni plating method and the rate of shielding effect is %. But this is almost for electric fieldwaves and,for the magnetic fieldwaves, it is a little one. In the 8 class metals such as Nickel, Iron(Fe), Cobalt(Co) has the character of clinging to magnet, this means those metals are superior to shield magnetic wave. That s why we have developed the Ni-Co alloying product in electroless plating method to satisfy not only electric fieldwaves but also magnetic waves. Property Property Value Remark Material Polyester plating Ni-Co. - Total thickness (mm) NC100S 0.1 ± 0.05 Except Release Liner NC050S 0.05 ± Peel Strength (gf/in) Min KS A 1107 Holding Power(40 C, 1kg) Max. 3 (mm) Ball tack (Ball No.) 7 ± 1 J. Dow Method Color Silver - Surface Conductivity (Ω/sq) Max Volume Conductivity (Ω/in 2 ) Max Width (mm) Max Length (M/roll) Min. 50 -

5 DOUBLE COATED ADHESIVE CONDUCTIVE TAPE WITH DIFFERNCE ADHESION (IT3-T0305LH/T0810LH) ITPLUS Conductive Double Coated Adhesive Tape is isotropically pressure sensitive adhesive tapes. IT3-T0305LH/T0810LH have differential adhesion on each side for providing good rework and repositioning. Application IT3-T0305LH T0305LH / T0810LH double coated conductive tapes are typically used for applications requiring excellent electrical conductivity from a substrate to the opposite substrate through the tape. Common uses include grounding and EMI shielding in equipment, components, shielded rooms, etc. Structure Property Conductive Acrylic adhesive (Low Adhesion) Conductive Fabric Conductive Acrylic adhesive (Low Adhesion) Release Liner Property T0305LH T0810LH Remark Backing Thickness (mm) 003± 0.03 ± ± 0.08 ± /1000 gauge Total Thickness (mm) 0.05 ± ± Except Release Liner Adhesion (gf/25mm) Low adhesive side High adhesive side Holding Power (40 C, 1 Kg) (mm) 200 ± ± 100 KS A 1107 Min Min KS A 1107 Max. 2 KS A 1107 Ball Tack (no.) 5 ±1 J. Dow Method Surface Resistance (Ω/sq) Max Kg Volume Resistance (Ω/in 2 ) Max Kg Color Dark Gray - Width (mm) Max Length (m/roll) Min. 50 -

6 NICKEL FOIL CONDUCTIVE TAPE (IT3-1025/ 2035) ITPLUS conductive foil Tape is typically used for applications requiring i excellent electrical l conductivity from the application substrate through the adhesive to the foil backing. Common uses include grounding and EMI shielding in equipment, components, shielded rooms, etc. Structure < IT /One side adhesive> <IT /Double side adhesive> Nickel Foil Conductive adhesive Release Paper Conductive adhesive Nickel Foil Conductive adhesive Release Paper Property Property Value Remark Backing Thickness (mm) 0.07 Digital Upright Gauge Total Thickness (mm) Adhesion (gf/25mm) IT ± 0.01 Except Release Liner IT ± 0.01 IT KS A 1107 IT Holding Power (mm/hour) 1 under KS A 1107 Surface Resistance (Ω/in) Less 0.1 MIL DTL 83528C Volume Resistance (Ω/in 2 ) Less 0.1 MIL DTL 83528C Color Metal Silver - Temperature (Min/Max) ( C) -10 to 80 ASTM D 3330

7 CONDUCTIVE TENSION RESIN(TR) CUSHION SHEET Cu TR Cu Polyolefin It is a polyolefin foam with holes on the surface. With plated holes, it has conductivity not only surface, also up & down. The polyolefin foam material is that added flexibility and heat-resistance property into Polyethylene. Also as an excellent material for FR (Flame Retardant) and molding, It is used for various application with its superior characters such as cushion, water- resistance, chemical character and etc. Non-woven conductive Tape Product Characteristics Material Material Polyolefin Backing Thickness Tape(Non-Woven) mm 0.19 ± 0.03 Plating Method Ni+Cu+Ni+water PU Tape Thickness mm 0.21 ± 0.03 Release liner excluding Color Dark Gray 180 Peel Strength gf/in min.900 KS A 1107 Material Weight 0.25 ± 5 ASTM D3776 Holding Power (40 C, 1kg) Thickness(mm) 0.5 ± 0.1 ASTM D1777 sec min.3600 KS A 1107 Width(mm) 1020 ± 20 Ruler Ball tack Ball no. 7 ± 1 J Dow Method Resistance Surface 0.08 MIL G Surface Resistance Bottom 0.03 Top-Bottom resistance Ω max kgf/in 2 Ω max.0.1 1kgf/in 2 SE db 60 ASTM 4935 Color Dark Gray Ruler min.900 Ruler RoHS Status RoHS Material Pass/Fail RoHS Material Pass/Fail Lead(Pd) PASS ICP-AES Mercury(Hg) PASS ICP-AES Cadmium(Cd) PASS ICP-AES Bromine Compound Hexavalent PASS UV-Vis Chromium (Cr6) PBBs PASS GC/MS PBDEs PASS GC/MS 1. High elasticity and superior restoration as Conductive cushion 2. Various thickness is available 3. Good plating adhesion and excellent preventing finger print effect with water polyurethane treating 4. Effective way to replace conductive poron & sponge

8 BU (Conductive Foam) This Product is developed to be able to simplify a process of existing conductive foam gasket, basic material is Urethane and it has superior processing property and conductivity. And with minute plated holes, it has conductivity not only surface, also through top & bottom (vertical) Ag PU Product Characteristics This is bonded Urethane material with fabric in order to reinforce tensile strength, so it is possible to be applied to itself as foam material. And according to the customer s option or requests, thickness could be adjusted by using different conductivity tapes. Item BU-0.3 B U-0.5 BU-0.7 Material Weight (g/m 2 ) 171.8± ±A ±102±10 Thickness (mm) 0.33± ± ±0.05 Width (mm) 11050±20 Tensile strength N/50mm L: 210/w:250 L: 210/w:250 L: 260/w:250 Elongation % L: 21/w:17.5 L: 21/w:16 L: 24/w:17.5 Resistance Surface Less than0.1 Less than0.1 Less than0.1 Vertical Less than0.05 Less than0.05 Less than0.05 db More than 60 More than 60 More than 60 RoHS Status RoHS Material Pass/Fail RoHS Material Pass/Fail Lead(Pd) PASS ICP-AES Mercury(Hg) PASS ICP-AES Cadmium(Cd) PASS ICP-AES Bromine Compound Hexavalent PASS UV-Vis Chromium (Cr6) PBBs PASS GC/MS PBDEs PASS GC/MS Existing foam gasket if formed by 3 kinds of materials which are conductive fabric, Urethane foam, double side tape and through separate progress then it is made up into one. According to give conductivity to the foam itself in this progress, BU product was invented and possible to be used as thin gasket. This technique comes form treating tape adhesion direct on foam material so foam tape can be used as a substitution for gasket. Possible for each thickness as 0.3T, 0.5T, 0.7T and also product specialty if superior

9 SHIELD FOAM GASKET EMI gaskets are designed for shielding and grounding in electronic devices. It consist of a conductive fabric wrap over a compressible PU foam core. Pressuresensitive adhesive attachment tape is provided for easy application 1. Technical Data for Conductive Fabric Part No Woven Base Woven Material Compound Acrylic material Hot melt adhesive including Rubber, Polyurethane and EVA Thickness(mm) 0.12 ± 10 % U.L Flame Class - Remarks Part No Rip-stop Base Rip-stop Material Compound Acrylic material Hot melt adhesive including Rubber, Polyurethane and EVA Thickness(mm) 0.13 ± 10 % U.L Flame Class - Remarks Structure of PET/ Plating Metal Surface Resistivity SE(dB) [30MHz~1 GHz) Ripstop / Cu+Ni Woven / Cu+Ni Ripstop / Cu+Au

10 SHIELD FOAM GASKET 2. Technical Data for Foam Name SPECIFICATION Material PU foam Density 32±3Kg/ m3 45±3Kg/ m3 Tensile Strength(kgf/ cm2 [psi]) 0.8[11.4] 1.0[14.2] Elongation (%) Tear Resistance (N/m) Compression Set (%) Technical Data for Adhesive Type Thickness Contact Service Temp Adhesive (mm) Resistivity strength Conductive 0.11mm 0.05 Ω/ cm Nonconductive Shielding Effectiveness

11 SHIELD FOAM GASKET Optional Gasket Shape Part Number Formula PN : F K R Type of Spong F : PU Foam 45Kg S : PU Foam 32Kg M : PU Foam 45Kg(White) +NON Dioxin Flame Retardant Fabric S : Silicone A : AL Foil 2 Type of Fabric K : Woven, R : Rip-stop, G : Gold, AL : AL Foil 3 Width (mm) 4 Type of Shield foam Shape None : Rectangular Type(Standard) R, L, LT, P 5 Height (mm) 6 Length (mm) 7 Type of Pressure Sensitive Adhesive Tape 00 : Non Conductive Tape 15 : Conductive fabric tape

12 CONDUCTIVE PAINT Conductive paint provides EMI shielding and surface grounding in a various applications. This conductive paint, air/heat chamber-dry paints are intended for EMI shielding of insulated substrates. Conductive paint, Silver Paste, provide high levels of EMI shielding effectiveness on a various plastic materials used for electronic devices. Silver Paste Content NSP Conductive powder Silver System Solvent base Binder Thermoplastic Solid content 40 ± 1 (wt %) Diluents EtOH : Acetone = 1 : 1 Coverage (Dry film) 12.5 μm Surface resistivity Max. 0.20Ω/ Drying time 30 min at RT 20 min at 60 Shielding effectiveness Min 60 db Ag/Cu Paste Content SCE608 Conductive powder Silver coated copper Nonvolatile(%) 29.0 ± 1 Specific gravity (25 ) Resistivity 1.12 ± 0.05 < Ohm/Sq (Dry film thickness : 25μm )

13 TOUCH SCREEN PASTE Touch Screen Paste is an electrode ec material a package for touch screens that offers outstanding linearity, adhesiveness, and low temperature drying conditions. Also that is adequate for various touch screen such as cell phones, PDA, and navigation systems. Paste Characterization Item Viscosity (cps) Property 20,000± 10,000 Remark Viscometer : Brookfield HB 3 RPM Filler/ Binder Silver/ Polyester Solid Content (wt.%) 78 ± 2 Flash Point 105 o C Density (g/cc) 2.8 Shelf Life 3 Month under original seal Storage Temp. < 25 o C Screen Print Test Condition Mask Process Grade SUS 500 Opening 33 um Mesh width 18 um Mesh Height 25 um Emulsion Thickness 10 um Squeeze Head Speed 0.13 m/sec Clearance 2 mm Squeeze Pressure 12mm(Base: 1.2 Substrate)

14 TOUCH SCREEN PASTE Pattern Image Iso. Line μm Snake Pattern_80/ μm Iso. Line μm Snake Pattern_100/ μm Performance Item Performance NSP-TS200 Resolution (min. line/space) 70 um / 70 um Cured Film Thickness 8 um Rs (ohm/sq) Resistivity Volume Resistivity (ohm * cm) 5 E-5 Adhesion (Cross Cut Test) 100/100 Flexibility (Number of 360 o Bending Cycles to Crack Initiation) > 1

15 CONDUCTIVE SILICONE Our conductive silicones are strips and sheets that are available in a various sizes. Also provide various type using special filler materials. They have excellent performance in electrical and mechanical property. Technical Data Conductive Filler SC SA NC CC Method Unit Binder Silicone ASTM Volume Ω * cm D257 Resistivity Electrical Shielding db > 80 > > Effectiveness Specific Gravity ± D792 Hardness Shore A (± 5) 50 ~ ~ 80 65~ ~ 70 D2240 Physical Tensile kgf/ cm2 Strength [psi] 30 [430] 20 [285] 20 [285] 60 [850] D412 Tear Strength kn/m D6248 Elongation % D412 Service Temp. c -50~125-50~150-50~150-50~170 SC (Silver coated Copper), SA (Silver coated Aluminum), NC (Nickel coated Graphite), CC (Conductive Carbon) Part Number Formula P/N : SC-AA-BB-CC-DD Material : SC, SA. NC, CC 2 Type : O, OO, D, DO, S 3 Size (mm) 4 Size (mm) 5 Length(mm)

16 CONDUCTIVE SILICONE Extrusion Type OO-Type Strip S-Type Strip P/N Nominal Diameter O.D I.D OO OO OO OO OO OO OO OO OO OO OO OO OO OO P/N Nominal Dimension W H R R R R R R R R R R R R R R

17 CONDUCTIVE SILICONE O-Ring Strip Type P/N Nominal Groove Nominal Groove P/N Diameter W D Diameter W D O O O O O O O O O O O O O O O O O O O O O O O O O O D-Ring Strip Type Groove Nominal Dimension P/N Dimension P/N Nominal Dimension Groove Dimension W H R W D W H R W D D D D D D D D D D D D D D D D D D D O-Ring Strip Type Nominal Dimension P/N W H r t DO Application Packing/Shielding for cable entries in casings Packing/Shielding for electronic equipment casings or frames Packing/Shielding for open entrance which should be dustproof and waterproof

18 FINGER STRIP Finger strip gaskets combine excellent EMI shielding effectiveness with anti-rub properties. Finger strip metal's strength, and electrical conductivity are good for shielding. Also we can provide with pressure sensitive adhesive. We have standard length and custom lengths are available. Main Raw-Material Property BeCu Alloy(C17200) & PSA TAPE Chemical Composition Mechanical & Electrical Properties PSA Be 1.8 ~ 2.0% Tensile Strengthth 1220 ~ 1480 (kgf/ cm3 ) [171 ~ 206 psi] 2860 ~ 3570 Co + Ni 0.2% 30 [ 430 psi ] [400 ~ 508 psi] Acrylic Co + Ni + Fe 0.6% 6 36 ~ 43 Adhesive Pb 0.02% ~ 105 Cu Balanced Strip Finger Application Front panel Handles Chassis Covers Plug-in Units Back Planes SMD Finger Application Grounding Fixing the Shield Can Battery contacts Part Number Formula IT4-AAA-BBB Serial Number 2 Length(mm)/Pin

19 EMI ABSRBER SHEET EMI absorber sheets are used to reduce a noise problems in a lot of electrical devices, and we offer some kind of absorber product. This absorbers can be installed easily with pressure sensitive adhesive. Features Effective frequency range : 10MHz to 18GHz Product thickness ranging from 0.1 ~ 1.0mm for applications in various products Certified grade for incombustibility (UL94V0) Applications Mobile phone SAR(Specific Absorption Rate) reduction In electronic products (TV, PC, notebook computer, etc.), EM wave absorbing RFID tag, antenna read range calibration (in the case of metal interference) Applications in munitions industry : radar avoidance (stealth technology) Core processing technology 1. Metal Alloy : unique combination design through metal synthesis (Co - precipitation method) 2. Metal Flake : Metal flake technology with an aspect rate of 350 ~ Metal Paste, Ink : Organic materials coating and dispersion (water and oil based) technology for flake metal 4. Compounding : technology for adequate composition of resin and metal 5. Metal Sheet : Unidirectional laminating technology of flake metal and thin film sheet

20 EMI ABSRBER SHEET Product Characteristics(M1 series) PROPERTY UNIT TEST METHODE ABSORBER Standard thickness mm KSM ISO ~ 1.3 Standard size mm - 220mm x 25, 50, 100m Temperature range to +100 Specific gravity ± Surface resistance Ω JIS K Thermal conductivity W/m K ASTM D ± 0.1 Tensile strength kg / cm2 ASTM D 638 > 100 Return Loss vs. Frequency

21 EMI ABSRBER SHEET Product Characteristics(M2 series) PROPERTY UNIT TEST METHODE ABSORBER Standard thickness mm KSM ISO ~ 1.2 Standard size mm - 220mm x 25, 50, 100m Temperature range to +100 Specific gravity ± Surface resistance Ω JIS K Thermal conductivity W/m K ASTM D ± 0.1 Tensile strength kg / cm2 ASTM D 638 > 100 Return Loss vs. Frequency

22 EMI ABSRBER SHEET (MSH-NF) The metal absorbing sheet is designed specifically for MHz. And it can make a cost reduction at almost 20~30% comparing with other competitor through processing rationalization because the whole producing process done in one line. ITPLUS can supply with optimized tuning according to the properties of loop antennas. SPECIFICATION TYPE Frequency Range (MHz) Operating temperature ( ) Thickness (mm) MSH-NF and adjacent band -25~ ~1.2 PRODUCT CHARACTERISTICS 1) Permeability test Agilent 4294A (1 khz -1 GHz ) Impedance Analyzer 2) Inspection sheet MSH-NF series (Permeability u = 30) Property Unit Test Method MSH-NF-4025 MSH NF-4050 Standard Thickness mm KSM ISO ± ±0.04 Standard d Size mm - 210mm x 50M 210mm 30M Permeability (at 10Mhz) U Impedance Analyzer 30 Temperature range C up to +100 Specific gravity ± 0.2 Surface resistance Ω JIS K x 10 9 Thermal conductivity W/ m K ASTM D ± 0.1 Tensile strength Kg/ cm2 ASTM D 638 >100 Elongation % ASTM D 638 > 60 Halogen - - Non- Halogen, Vo

23 Characteristics(MSP/MSH/MSD series) Product EMI ABSRBER SHEET (M1/M2) PROPERTY UNIT TEST METHODE ABSORBER Standard thickness mm KSM ISO ~ 1.2 Standard size mm - 220mm x 25, 50, 100m Temperature range to +100 Specific gravity Surface resistance Ω JIS K Thermal conductivity W/m K ASTM D ± 0.1 Tensile strength kg / cm2 ASTM D 638 > 100 Return Loss vs. Frequency 60 Real Imag. 40 Real Imag. permeability (? Complex permeability (? Complex M 10M 100M 1G Frequency (Hz) 0 1M 10M 100M 1G Frequency (Hz) MSP (Permeability u = 50) MSH(Permeability u = 50) Real Imag. Comp plex permeability (? M 10M 100M 1G MSD(Permeability Frequency (Hz) u = 50)

24 EMI ABSRBER SHEET-RF FILM IMAC is the innovative film that resolves demerits from existing complicate cable structures. Removing expander, EMI ceramic core, Mylar tape and EMI absorbing sheet in Cable but only wrapping MAC, Customers can experience both cost-effectiveness and better EMI shielding quality. Application Existing cable structure (2.6mm cable) Data link Power line Ground wire Woven Cu (Sample 2) Heat-resistant insulator Measures against noise on existing cable structure Woven Cu, Ceramic core, EM wave absorbing sheet for outlets After using Absorbing-shielding film(ac-1000h) for electrical wire (Sample 3) Removal of woven Cu, ceramic core, and EM wave absorbing sheet from the above existing cable structure Conclusion 1.Saving Producing Cost 2. Good Performance of EMI Shielding

25 THERMAL CONDUCTIVE SILICONE PAD The objective of thermal interface material in electronic devices is the efficient removal of heat from the ambient environment. These materials are formulated with silicone that are loaded with thermally conductive fillers. We provide the best performance materials and solutions in the thermal interface materials. Data Sheet Overview PROPERTY REMARK Color Dark Gray Dark Gray Dark Gray Gray Visual Thickness(mm), One layer 0.1 ~ ~ ~ ASTM D374 Specific Gravity KSF 4910 Hardness (Shore 00) ASTM D2240 Continuous Use '-60 ~ 200 '-60 ~ 200 '-60 ~ 200 '-60 ~ Temp.( ) 200 ELECTICAL Dielectric Breakdown Min. 10KVdc/m Min. 10KVdc/ Min. 10KVdc/ Min. 10KVdc/ Voltage(Vdc) m mm mm mm ASTM D149 Dielectric Constant (1000Hz) ASTM D150 Volume Resistivity (Ω-cm) ¹⁴ ¹⁴ ¹⁴ ¹⁴ ASTM D257 Flame Rating V-0 V-0 V-0 V-0 UL94 THERMAL Thermal Conductivity (W/m-K) ASTM D5470 Application High speed Mass Storage Drives Power Suppliers Micro Processors, Memory Chips and Chipsets Thermal Solution for Heat Pipe Automotive Engine Control Units Telecommunication Hardware PN : IT1 AAA-BBB-CCC-DDD-EEE-FFF Serial Number 2 Thickness (mm) : 0.25, 0.5, 1.0, 1.5, ~ Width (mm) : Custom size 4 Length (mm) : Custom size 5 Type : G-gel type, R-rubber type, T-tape type 6 Thermal Conductivity (W/mK) : 1.0/1.5/2.0 7 Tape 00 : Nothing 10 : Silicone

26 DOUBLE ADHESIVE THERMAL FOAM TAPE ITPLUS thermal conductive acrylic foam tapes are applied to heat source and heat sink of electronic parts to make good heat emission. It can finalize manufacturing process without using rivet or screw, so they make working process simple and maintain clean surface The need of heat emission equipment It promptly emits the heat generated by the operation of electronic parts, preventing enting overheating and making good operation possible. Property Property Value Remark Adhesive Acrylic - Material Acrylic Foam - Color White - Thickness (mm) 0.5/0.4/0.25±0.05 ASTM D 374 Thermal Conductivity(W/m-K) 0.8 Hot wire Method(QTM) Release Liner Paper,PE, PET - Standard size 400mm x 33M Other size available Adhesion Strength (gf/25mm) 2600 ASTM D-3330 Holding Power 12 ASTM D-3654 Dynamic Shear Strength(gf/ cm2 ) 20minutes passed Dynamic Shear Strength(gf/ cm2 ) 24 hours passed 4500 ASTM D ASTM D-1002

27 Application Note PC Cable Shield Hard Disk Shield EMI Paint Case / Chassis Shield Keyboard Shield SD RAM Shield Cable Shield

28 Application Mobile Phone Speaker Mesh EMI Gasket Main/Sub LCD EMI Paint Dispensing Gasket LCD TV BLU Chassis EMI / ESD Shield TR-O Gasket Shield TR-O Gasket Shield

29 Application Rack Gasket EMI / ESD Shield Gasket EMI / ESD Shield Front Door Mesh Shield Cable / Camera Flat Cable Shield Camera Shield