ANSI and IEC Color Codes

Transcription

1 ANSI and IEC Col Codes f s, Wire and Connects All OMEGA TM Wire, Probes and Connects are available with either ANSI IEC Col Codes. In this Handbook, model numbers in the To Order tables reflect the ANSI Col-Coded Product. ANSI Code J K T E N Connects ANSI/ASTM E-230 Col Coding Grade Extension Grade Alloy Combination Lead Lead IRON Fe (magnetic) CHROMEGA TM - CHROMIUM Ni-Cr CHROMEGA TM - CHROMIUM Ni-Cr OMEGA-P TM NICROSIL Ni-Cr-Si CONSTANTAN - -Ni ALOMEGA TM - ALUMINUM Ni-AI (magnetic) CONSTANTAN - Ni CONSTANTAN - -Ni OMEGA-N TM NISIL Ni-Si-Mg IEC Col Coding Maximum EMF (mv) T/C Grade Over Max. Grade Comments Environment Temp. Temp. Bare Wire Range Range Reducing, Vacuum, Inert. Limited Use in Oxidizing at High Temperatures. Not Recommended f Low Temperatures. Clean Oxidizing and Inert. Limited Use in Vacuum Reducing. Wide Temperature Range, Most Popular Calibration Mild Oxidizing, Reducing Vacuum Inert. Good Where Moisture Is Present. Low Temperature & Cryogenic Applications Oxidizing Inert. Limited Use in Vacuum 270 to 1000 C Reducing. Highest EMF 454 to 1832 F Change Per Degree Alternative to Type K. Me Stable at High Temps 210 to 1200 C 346 to 2193 F 270 to 1372 C 454 to 2501 F 270 to 400 C 454 to 752 F 270 to 1300 C 450 to 2372 F to to to to to Connects Intrinsically Safe IEC Code J K T E N R PLATINUM- 13% RHODIUM Pt-13% Rh Platinum Pt Oxidizing Inert. Do Not Insert in Metal Tubes. Beware of Contamination. High Temperature 50 to 1768 C 58 to 3214 F to R S PLATINUM- 10% RHODIUM Pt-10% Rh Platinum Pt Oxidizing Inert. Do Not Insert in Metal Tubes. Beware of Contamination. High Temperature 50 to 1768 C 58 to 3214 F to S R/ SX U* -LOW -Ni Extension Grade Connecting Wire f R & S s, Also Known as RX & SX Extension Wire. Uncompensated f use with RTDs and Thermists R/ SX U B G* (W) C* (W5) D* (W3) PLATINUM- 30% RHODIUM Pt-30% Rh TUNGSTEN W 5% RHENIUM W-5% Re 3% RHENIUM W-3% Re Platinum- 6% RHODIUM Pt-6% Rh 26% RHENIUM W-26% Re 26% RHENIUM W-26% Re 25% RHENIUM W-25% Re Oxidizing Inert. Do Not Insert in Metal Tubes. Beware of Contamination. High Temp. Common Use in Glass Industry Vacuum, Inert, Hydrogen. Beware of Embrittlement. Not Practical Below 399 C (750 F). Not f Oxidizing Atmosphere Vacuum, Inert, Hydrogen. Beware of Embrittlement. Not Practical Below 399 C (750 F) Not f Oxidizing Atmosphere Vacuum, Inert, Hydrogen. Beware of Embrittlement. Not Practical Below 399 C (750 F)Not f Oxidizing Atmosphere 0 to 1820 C 32 to 3308 F 0 to 2320 C 32 to 4208 F 0 to 2320 C 32 to 4208 F 0 to 2320 C 32 to 4208 F 0 to to to to C (W5) D (W3) * Not official symbol standard designation JIS col code also available. H-3 NO STANDARD USE ANSI COLOR CODE NO STANDARD USE ANSI COLOR CODE NO STANDARD USE ANSI COLOR CODE B G (W)

2 Tolerances (Reference Junction at 0 C) American Limits of Err ASTM E230-ANSI MC 96.1 ANSI Code Standard Limits Special Limits Temp Range >0 to 750 C >32 to 1382 F 0 to 750 C 32 to 1382 F Tolerance Value 2.2 C 0.75% 4.0 F 0.75% 1.1 C 0.4% 2.0 F 0.4% Temp Range >0 to 1250 C >32 to 2282 F 0 to 1250 C 32 to 2282 F Tolerance Value 2.2 C 0.75% 4.0 F 0.75% 1.1 C 0.4% 2.0 F 0.4% Temp. Range* -200 to 0 C -328 to 32 F Tolerance Value 2.2 C 2.0% 4.0 F 2.0% Temp Range >0 to 350 C >32 to 662 F 0 to 350 C 32 to 662 F Tolerance Value 1.0 C 0.75% 1.8 F 0.75% 0.5 C 0.4% 1 F 0.4% Temp. Range* -200 to 0 C -328 to 32 F Tolerance Value 1.0 C 1.5% 1.8 F 1.5% Temp Range >0 to 900 C >32 to to 900 C 32 to 1652 F Tolerance Value 1.7 C 0.5% 3 F 0.5% 1.0 C 0.4% 1.8 F 0.4% Temp. Range* -200 to 0 C -328 to 32 F Tolerance Value 1.7 C 1.0% 3 F 1.0% Temp Range >0 to 1300 C >32 to 2372 F 0 to 1300 C 32 to 2372 F Tolerance Value 2.2 C 0.75% 4.0 F 0.75% 1.1 C 0.4% 2.0 F 0.4% Temp. Range* -270 to 0 C -454 to 32 F Tolerance Value 2.2 C 2.0% 4.0 F 2.0% Temp Range 0 to 1450 C 32 to 2642 F 0 to 1450 C 32 to 2642 F Tolerance Value 1.5 C 0.25% 2.7 F 0.25% 0.6 C 0.1% 1 F 0.1% Temp Range 800 to 1700 C 1472 to 3092 F Not Tolerance Value 0.5% 0.5% Established Temp Range 0 to 2320 C 32 to 4208 F Not Tolerance Value 4.5 C 1.0% 9 F 1.0% Established H * Not official symbol standard designation Whichever value is greater. Note: Material is nmally selected to meet tolerances above 0 C. If thermocouples are needed to meet tolerances below 0 C, the purchaser shall state this as selection of material is usually required. IEC Tolerance Class EN ; JIS C 1602 IEC Code Class 1 Class 2 Class 3 J K N T E R S Temp Range -40 to 375 C -40 to 333 C Tolerance Value ±1.5 C ±2.5 C Not Temp. Range 375 to 750 C 333 to 750 C Established Tolerance Value ±0.4% Reading ±0.75% Reading Temp Range -40 to 375 C -40 to 333 C -167 to 40 C Tolerance Value ±1.5 C ±2.5 C ±2.5 C Temp. Range 375 to 1000 C 333 to 1200 C -200 to -167 C Tolerance Value ±0.4% ±0.75% Reading ±1.5% Reading Temp Range -40 to 125 C -40 to 133 C -67 to 40 C Tolerance Value ±0.5 C ±1 C ±1 C Temp. Range 125 to 350 C 133 to 350 C -200 to -67 C Tolerance Value ±0.4% Reading ±0.75% Reading ±1.5% Reading Temp Range -40 to 375 C -40 to 333 C -167 to 40 C Tolerance Value ±1.5 C ±2.5 C ±2.5 C Temp. Range 375 to 800 C 333 to 900 C -200 to -167 C Tolerance Value ±0.4% Reading ±0.75% Reading ±1.5% Reading Temp Range 0 to 1100 C 0 to 600 C Tolerance Value ±1 C ±1.5 C Not Temp. Range 1100 to 1600 C 600 to 1600 C Established Tolerance Value ±[1 0.3% x (Rdg-1100)] C ±0.25% Reading Temp Range 600 to 800 C Tolerance Value Not 4 C Temp. Range Established 600 to 1700 C 800 to 1700 C Tolerance Value ±0.25% Reading ±0.5% Reading Material is nmally selected to meet tolerances above -40 C. If thermocouples are needed to meet limits of Class 3, as well as those of Class 1 2, the purchaser shall state this, as selection of material is usually required. H-4

3 Wire Insulation Identification Insulation Code PP EXPP) FF EXFF) TT EXTT) KK TG GG EXGG) HH XR XC Standard Braid XL-Loose Braid XT-Tight Braid XS TFE Overall Polyvinyl Chlide (PVC) FEP Kapton Glass Braid Polyvinyl Chlide (PVC) FEP Kapton -40 to 105 C -40 to 221 F -200 to 200 C -338 to 392 F -267 to 260 C -450 to 500 F -267 to 260 C -450 to 500 F -73 to 260 C -100 to 500 F Glass Glass -73 to 482 C Braid Braid -100 to 900 F High Temp High Temp -73 to 871 C Glass Glass -100 to 1300 F Braid Braid Good Excellent Good Excellent Good Excellent Excellent Good Excellent Excellent Good Good Good Good Excellent Po Good Po Po Good Po Refrasil Refrasil -73 to 871 C Po Good to Po to Braid Braid -100 to 1600 F 315 C (600 F) 315 C (600 F) Nextel Nextel -73 to 1204 C Braid Braid -100 to 2200 F Silica TFE Insulation Conducts Silica TFE Temperature Appearance of Range, Grade Wire Insulation -73 to 1038 C -100 to 1990 F -267 to 260 C -450 to 500 F Abrasion Resistance Flexibility Water Submersion Po Good Po Po Good Po Excellent Good Excellent ANSI col code shown To der IEC col code visit us online H-5

4 and Application Guide Resistance To: Solvent Acid Base Flame Humidity Comments Fair Good Good Good Good Col Coded PVC Extruded Over Each Bare Wire. PVC Applied Over Insulated Primaries. Affected by Ketones, Esters Col Coded FEP Extruded Over Each Bare Wire. FEP Applied Over Insulated Primaries. Superi Abrasion and Moisture Resistance. Good Good Good Good Excellent Excellent Excellent Excellent Excellent Fair Excellent Excellent Excellent Excellent Fair Col Coded Extruded Over Each Bare Wire. Jacket Extruded Over Insulated Primaries. Superi Abrasion and Moisture Resistance. Same Basic Characteristics as FEP but Higher Temperature Rating Fused Kapton Tape Approx mm Applied to Conducts. A 0.10 mm Jacket Is Then Applied to Both. Excellent Moisture and Abrasion Resistance, High Dielectric Strength (7 kv/mil) Retains Much Physical Integrity After Gamma Radiation. FEP Is Used as Adhesive Binding Agent (Melts at approx. 260 C [500 F]) Extruded Over Each Bare Wire and a Glass Braid on the Jacket. May Be Used f Single Measurement to 343 C (650 F) 0.12 mm Glass Braid Over Each Conduct, and Binder Impregnated. Overall Glass Braid Applied and Bindered. Binder Improves Moisture and Abrasion Resistance but Is Destroyed Above 204 C (400 F) High Temp. Glass Braid Over Each Conduct, and Binder Impregnated. Overall High Temp Glass Braid Applied and Bindered. Binder Improves Moisture and Abrasion Resistance but Is Destroyed Above 400 F H Excellent Good to Good to 315 C (600 F) 315 C (600 F) Excellent Po Braid of Vitreous Silica Fiber Applied to Each Bare Wire, Then Over Both. Suitable to 982 C (1800 F) if Not Subjected to Flexure Abrasion Excellent Good Good Excellent Fair High Temp, Alumina-Bia-Silica Ceramic Fiber Braided Over Each Conduct Then Over Both. Not Recommended f Platinum s Exposure to Molten Tin and Copper, Hydrofluic Phosphic Acids, Strong Alkalies Excellent Good Po Excellent Fair Silica Is a Very High Purity, Chemically Stable Yarn. (SiO2 Content 99%) Col Coded TFE Tape Applied to Conducts and Jacket. Superi Abrasion, Moisture, and Chemical Resistance. ANSI col code shown To der IEC col code visit us online H-6

5 Reference Guide Temperature Range OMEGACLAD TM is a three-part system composed of compacted MgO insulation, thermocouple wire and metal sheath. Four facts determine the useful service temperature f OMEGACLAD TM assemblies. U Properties of the Sheath Material U Diameter and Construction of Assembly U Range f the Wire (See Table of Err) U Maximum Service Temperature of Insulation. In the Case of MgO, this is in Excess of 1650 C (3000 F) Sheath Material Specifications Melting Continuous Tensile (psi) Strength Point 537 C Material ( C/ F) Temp. ( C/ F) (200 F) (1000 F) 304 SS 1405/ / ,000 15, SS 1405/ / ,000 27, SS 1370/ / ,000 23, SS 1400/ / ,000 17,000 Inconel* 1400/ / ,000 5,000 SUPER XL 1400/ / ,000 17,000 * Oxidizing, Vacuum Inert atmosphere only Conduct Size Equivalents Upper Temperature Limit in C ( F) of Protected Bare Wire s Vs. Wire Diameter T/C Wire Size Type 8 AWG 14 AWG 20 AWG 24 AWG 28 AWG 30 AWG 36 AWG 0.128" 0.064" 0.032" 0.020" 0.013" 0.010" 0.005" Common Junctions Grounded Exposed Ungrounded H (1400) (1100) (900) (700) (700) (600) (590) (2300) (2000) (1800) (1600) (1600) (1400) (1100) (1600) (1200) (1000) (800) (800) (700) (600) (700) (700) (500) (400) (400) (300) (400) (400) (400) (400) (400) (300) (2300) (2000) (1800) (1800) (1800) (1600) (800) (800) (800) (800) (800) (752) Gage AWG SWG GAGE AWG SWG No. inches mm inches mm No. inches mm inches mm AWG = American Wire Gage To convert from AWG to SWG: Determine wire diameter in inches (mm) from appropriate AWG. SWG = (British) Standard To convert 30 AWG to SWG, determine that 30 AWG is ", which is equivalent to 33 SWG Wire Gage Bends Easily! Twisted Shielded Wire Upper Temperature Limit in C ( F) of OMEGACLAD TM Vs. Sheath Diameter Sheath 0.020" 0.032" 0.040" 0.062" 0.093" 0.125" 0.188" 0.250" TC. Dia. 0.5 mm 0.8 mm 1.0 mm 1.6 mm 2.4 mm 3.2 mm 4.8 mm 6.3 mm & Metal Sheath Magnesium Oxide Insulation Wires 260 (500) 260 (500) 260 (500) 440 (825) 480 (900) 520 (970) 620 (1150) 720 (1300) 700 (1290) 700 (1290) 700 (1290) 920 (1690) 1000 (1830) 1070 (1960) 1150 (2100) 1150 (2100) 300 (570) 300 (570) 300 (570) 510 (950) 580 (1075) 650 (1200) 730 (1350) 820 (1510) 260 (500) 260 (500) 260 (500) 260 (500) 260 (500) 315 (600) 370 (700) 370 (700)

6 The combination of chemical and physical properties of FEP and is a result of its true fluocarbon structure. This unusual structure leads to a material which has an almost universal chemical inertness; complete insolubility in all known solvents below 300 C (572 F); excellent thermal stability; and unsurpassed electrical properties including low dielectric loss, low dielectric constant and high dielectric strength. Furtherme, FEP and does not embrittle at very low temperatures. Available in pre-spooled lengths Properties of and FEP Insulation General Properties of FEP & FEP Chemical Resistance: hydrocarbons, ethylene glycol, battery acid, brake fluids, other chemicals NO EFFECT NO EFFECT Resistance to weathering NO EFFECT NO EFFECT Water absption (ASTM D570) 0.1% 0.1% Flammability (UL 83, Vertical Wire Flame Test)* NO AFTER BURN NO AFTER BURN Melting Point F 518 F 590 F Melting Point C 270 C 300 C Upper Service Temperature C ( F) 1500 to 2000 hrs. estimated 200 C (392 F) 288 C (550 F) 20,000 hrs. 177 C (350 F) 260 C (500 F) Cold -65 C 2.5 K V f 5 min. PASS PASS Specific gravity Mechanical and Electrical Properties FEP Tensile strength, psi 23 C (73 F) ASTM D Elongation, % 23 C (73 F) ASTM D Flexural modulus, psi 23 C (73 F) ASTM D790 95,000 95,000 Flex life, MIT (7 to 9 mils) 82 C (180 F) Flexes 100, ,000 Impact Strength, ft.lb/inch.: ASTM D256 Room temperature NO BREAK NO BREAK -54 C (-65 F) Coefficient of friction, 10 fpm, 100 psi Dynamic cut-through (lb) Instron 1 16" radius blade moving at 0.2"/min. (0.0031" insulation thickness) 23 C C 73 Dielectric constant, ASTM D Volume resistivity, ohm-cm ASTM D Dissipation Fact, ASTM D150, Hz H Resistance vs. Wire Diameter [Resistance in ohms per double 20 C (68 F)] Type K Type J Type T Type E Type S Type R Type RX/SX Type C Type CX Type G Type D Type BX AWG Diameter CHROMEGA / Iron/ Copper/ CHROMEGA / Pt/ Pt/ Copper W5%Re/ Alloy 405/ W/ W3%Re Copper/ No. inches mm ALOMEGA Constantan Constantan Constantan Pt10%Rh Pt13%Rh Alloy11** W26%Re Alloy 426 W26%Re W25%Re Copper* * Increase the resistance by 19% f nickel plated, Type RTD wire. ** Maximum Resistance of reviewed wire. Not ANSI symbol. Resistivity f N is times Type K values. H-8

7 How to Specify Wire, Connects and Probes with ANSI IEC Col Codes Shown actual size. Wire To der IEC col coded wire, add the suffix I after the thermocouple type letter TT-K-20-50M (f reference only) over Insulation, Type K, col code, 20 gage wire, 50 meters long TT-KI-20-50M over Insulation, Type K, IEC col code, 20 gage wire, 50 meters long Shown smaller than actual size. Connects To der IEC col coded connects, add the suffix I after the thermocouple calibration letter OSTW-K-MF OST write-on connect, Type K, col code, male/female* pair OSTW-KI-MF OST write-on connect, Type K, IEC col code, male/female* pair * Supplied with the exclusive universal write-on female connect, another OMEGA manufactured innovation. At OMEGA, the mating connect and hardware are always included with probes! Omegaclad TM Probes To der IEC col coded Omegaclad probes, add the suffix I befe the M in the model number* KQIN-M30G-300 Type K, Inconel sheath, 3 mm diameter col code, 300 mm length KQIN-IM30G-300 Type K, Inconel sheath, 3 mm diameter, IEC col code, 300 mm length Shown actual size. Insulated Wire s Shown smaller than actual size. To der IEC col coded wire, add the suffix I after the thermocouple calibration letter 5TC-GG-K-20-1M (f reference only) Glass over glass insulated thermocouples, Type K, col code, 20 gage wire, 1 meter (1000 mm) long 5TC-GG-KI-20-1M Glass over glass insulated thermocouples, Type K, IEC col code, 20 gage wire, 1 meter (1000 mm) long Note: To der with JIS col codes, replace the letter I as described in the above examples with the letter A. Ordering Example: KQIN-AM30G-300, Type K, Inconel sheath, 3 mm diameter, JIS col code 300 mm length. F reference Connect col is blue in this configuration. H-9