Project: A NEW FOLEY K-6 SCHOOL FOR THE BALDWIN COUNTY BOARD OF EDUCATION BAY MINETTE, ALABAMA
|
|
- Joella Barber
- 6 years ago
- Views:
Transcription
1 McKee and Associates Architecture and Interior Design Addendum No. SIX Date: Project: A NEW FOLEY K-6 SCHOOL FOR THE BALDWIN COUNTY BOARD OF EDUCATION BAY MINETTE, ALABAMA PROJECT NO BC # A6.1 GENERAL A. The following changes and/or substitutions to the plans and specifications are hereby made a part of same and are incorporated in full force as part of the contract. B. Bidders shall acknowledge receipt of this Addendum in writing on his Proposal Form. C. See the following responses to RFI questions received from Contractor s 1. Hardware Set# 04A Set specifies both Rim Exit and Lockset Please advise which will be required? 1. Rim Exit is required. Add 1 EA closer to this set: # CL D-4551 TRI PACK SN Hardware Set#13 Set specifies Rim Exit, Except No Mullion was specified. Please advise if Exits will be Rim Type and Specify Mullion or if Intended to be surface Vertical Rod Exit 2214 LBR w/ Trim? 2. Surface V-Rods are required: # FL 2201 LBR
2 3. Hardware Set# 29 Openings # F125, F125A & F128. Set specifies Concealed Closer/Pivot package, Push plates and Armor Plates. Doors are type H Double Acting. Will these Doors be Traffic Doors specified in Section 08380? If so all Hardware would be Furnished by the Traffic Door Mfgr. 3. Hardware specified in set # 29 is correct. Doors to be double acting wood doors. 4. General Hardware Locksets Baldwin County maint. Supervisors have requested we do not use or specify Mortise Locksets for any new or additions. They have requested we furnish only the 9K3 Grade 1 Series Cylindrical Locksets. Please Advise to this change from the 45H Series Locks to the 9K3 Series Locksets? 4. Locksets/Latchsets shall be Best 9K3 series per the request of Baldwin County Schools. Replace all references to 45H series in section to 9K3 series. 5. Hardware Section Set # 01 Aluminum Storefront Doors A139A Set # 10 Aluminum Storefront Doors A139, A139B. These Exterior Aluminum Doors are tested with the Door manufacturers Hardware as an assembly. The Hardware specified could be used as a Basis of design but will need to be furnished by the Door Supplier. Will this hardware be furnished by the Door Manufacturer as required. 5. At hardware set # 01 - omit all hardware with the exception of the cylinders at opening # A139A. It will be the responsibility of the aluminum door supplier to furnish all other hardware that is required. Hardware at all other openings in this set shall be furnished as scheduled. At hardware set # 10 - omit all hardware with the exception of the cylinders at opening # A139, A139B. It will be the responsibility of the aluminum door supplier to furnish all other hardware that is required.
3 6. Hardware Section Hardware Set # 17 Aluminum Storefront Hardware. Please note: Hardware specified may be an issue for the Door Mfgr. In Most cases the ALSF Manufacturer wil use their own Exits and Pivot sets for this application. Will the ALSF Manufacturer furnish his own Pivots and Exits using the specified items as a Basis of Design? 6. Hardware to be furnished as specified. Section makes reference to section 08700; aluminum door suppliers may review specified hardware and furnish storefront material accordingly. 7. Hardware Sets # 26 & 28. Rim Exit Devices are specified with no Trim or Pulls. Will Trims or Pulls be required? If so, please specify the required Trim or Pull handles for the active door. 7. At set # 26, furnish (2) two offset pulls: equal to Hager 12L - 12" CTC, 630 MV3, AGION At set # 28, revise device at active leaf to 2103 CD 4903A. 8. General Hardware Note: Specification calls for all Cylinders to be keyed to the Existing BCS Key System, which is a Standard best Key System. However, several hardware sets have specified Patented Cormax. Will the Final Cores be standard or Patented Cormax for all Locksets and Cylinders? 8. Cylinders to be keyed to the existing Best "Standard" system. Delete all references to "CORMAX" or "PATENTED CORMAX".
4 1. What is the scope of Work at the existing buildings? 1. All to be Demolished except gymnasium. Drawing to be Provided. 2. Are we to use Fire Retardant wood for the Decking & Sleepers? 2. No Fire Retardant Decking or Sleepers Metal Deck provides Barrier. 3. Do we use PT fascia? 3. No. 4. What is the footing & block wall for on the east side of the kitchen & cafeteria? (can t find on Arch Drawings) 4. This is the Generator Enclosure See drawings A1.6 and detail 6 on A6.2. Note the enclosure was moved to the North Side of the Kitchen. Referencing sheet C3.0, 4 grease traps are shown in series and a grease waste line is shown going to the dumpster pad. However, sheet P1.6 only shows 2 of the traps and a branch line for the dumpster pad. Which sheet is correct? Both of the sheets are correct, as is the sanitary riser diagram on sheet P3.2 which shows four grease traps in series and the grease waste line from the dumpster pad drain. Note that sheet P1.0, because it is at a much smaller scale, also shows four grease traps.
5 Referencing sheet P2.6, a hot and cold line is going to the dumpster pad, but there are no specs for a faucet or floor drain at the pad. With respect to the faucet at the dumpster pad, it should be a Fiat 830-AA wallmounted faucet provided with an 889CC bracket, (or equals). The drain at that location should be the same as the floor drains in the typical locations. There is no need for a trap primer or a trap guard in this location. Sheet FP1.7 Riser Detail indicates a 6 pipe running back outside to a remote FDC location. However, Sheet C3.0 indicates, Provide FDC on Fire Main and no FDC piping. Please advise. The FDC shall be removed from the riser diagram and it should be installed as indicated by the civil engineering drawings. A6.2 SPECIFICATIONS A. Refer to Section 08700, Finish Hardware, revise as follows: 1. Add the following to Door #F132 in Hardware Set #1A B. Refer to Section 08700, Finish Hardware, add the following hardware set; HARDWARE SET 01a Door # F132 Qty Type Description Finish 1 Cont Hinge 661 HD - 83" FULL MORTISE CONCEALED Alum 2 CYLINDER AS REQUIRED 1 Mullion HC KR " AM Rim Exit F03 HC 2103 CD - 36" W DR LC 630AM 630AM 1 Closer CL D-4551 S "HVY DUTY STOP ARM" SN Spacer P45HD-110 SPACER BLOCK Kick Plate 190 S 10 X " AM Offset Pull 12L - 12" CTC, 630 MV3, AGION (AM) 630AM 1 W/Strip 870 SXN 17' (1@36, 2@84") T/Hold, J SA 36" X WS, J Drip Strip 810S - 40" Sweep + Drip 770 SAV - 36" 628
6 C. The following manufacturers are hereby approved subject to the plans and specifications: Section 05400, Cold Formed Metal Trusses: Trigon Steel Components, INC. Section 07200, Insulation: Cavity Wall Insulation: Kingspan Insulation Section 08100, Steel Doors & Frames: Commercial Door Products Section 08300, Tornado Resistant Openings: Commercial Door Products Section 08520, Aluminum Windows: All Seasons Section 09651, Luxury Vinyl Tile: Delta Flooring DNC Shaw Industries, Inc. Section 09999, Rubber Sports Flooring: Action Floor Systems, LLC Champion Flooring, LLC Dynamic Sports Construction, Inc. Section 10100, Markable Boards and Tackboards: Nelson & Adams AJW Architectural Products Section 10500, Metal Lockers: WEC Manufacturing. ASI Storage Solutions Section 11063, Stage Rigging and Equipment: Jansen Industries Section 12304, Laminate Clad Casework: Advanced Cabinet Systems D. Refer to Section 08300, Tornado Resistant Opening Systems Revise as Follows: HARDWARE SET 20 Door # E104, E108 Omit all hardware, with the exception of the cylinders at openings # E104, E108. It will be the responsibility of the Impact and Wind Resistant Aluminum Door Supplier to furnish all other hardware that is required.
7 E. Refer to Section Impact and Wind Resistant Aluminum Storefront Window Systems Revise as follows: Change all references to ICC to ICC Change all references to FEMA October 2008 to FEMA P March 2015 respectively. Section to include Impact and Wind Resistant Aluminum Doors Page Add the following after FRAMING SYSTEM DESCRIPTION ALUMINUM DOOR SYSTEM DESCRIPTION /8 Narrow stile door system. a. Stiles: 5 X 2 3/8 b. Top Rail: 2 3/4 X 2 3/8 c. Bottom Rail: 8 1/2 X 2 3/8 d. Muntin: 1 5/8 x 2 3/8 e. Glazing Stops: 1 Face 2. Finish: Factory-applied 3. Doors: All doors shall be totally factory fabricated (field fabrication is not acceptable). All joints and connections shall be tight, providing hairline joints and true alignment of adjacent members. The system shall incorporate a weep design allowing any water penetration or internal condensation to flow through the system and exit to the exterior at the horizontal members. 4. Material: All components will be constructed from extruded aluminum in 6061-T6 alloy / temper, or equal. 5. Glazing Material: Glass Clad Polycarbonate, Laminated Glass, IGU 6. Anchors: All anchorage will be a fully concealed 7. Gasketing: Interior glazing gaskets shall be closed cellular EPDM and Exterior gaskets will be solid EPDM 8. Hardware Required: 2 point lock Continuous hinge Continuous astragal Door coordinator Carry open device Panic bar Latch lock
8 Page Under the heading of MANUFACTURERS add the following: 2. Doors TH350 FEMA Compliant Door System by Insulgard Security Products A6.3 DRAWINGS A. See the attached Revised Drawings as follows: Volume #2: Sheet FP1.7 (Dated ) Sheet P2.5 (Dated ) END OF ADDENDUM SIX
9
10
Bidders shall acknowledge receipt of this Addendum in writing on his Proposal Form.
McKee and Associates Architecture and Interior Design Addendum No. THREE Date: 11.13.18 Project: A New Eastern Shore K-6 School for The Baldwin County Board of Education Bay Minette, Alabama McKee Project
More information1 3 4 Tie Rod Aluminum Swing Entrance Doors
Windows Curtain Walls Entrances Storefronts Series T200 Narrow Stile Series T300 Medium Stile T500 Wide Stile Configurations Narrow Stile (2 1 8 ) Medium Stile (3 1 2 ) Wide Stile (5 ) EFCO tie rod entrances
More informationDivision 08 OPENINGS TABLE OF CONTENTS
Division 08 OPENINGS TABLE OF CONTENTS 08 1000 GENERAL... 2 A. RELATED DIVISIONS... 2 B. GENERAL... 2 08 1000 DOORS AND FRAMES... 2... 2 B. EXTERIOR DOORS AND FRAMES... 2 C. DOOR FRAMES... 2 D. HOLLOW
More informationSECTION ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS
PART 1 GENERAL SECTION 08 1116 ALUMINUM-FRAMED HIGH PERFORMANCE THERMAL ENTRANCE DOORS 1.01 SECTION INCLUDES A. Aluminum-framed storefront, with vision glass. B. Infill panels of glass. C. Aluminum doors
More informationAluminum-Framed Entrances and Storefronts
University of New Hampshire University of New Hampshire Scholars' Repository Division 08 Openings Chapter 5 Technical Construction and Renovation Standards 1-25-2013 084113 - Aluminum-Framed Entrances
More informationSECTION HARDWARE
PART I - GENERAL 1.1 RELATED SECTIONS: Refer to Section 081000 for requirements regarding doors and frames. Refer to Section 085000 for requirements regarding windows. 1.2 SCOPE OF SECTION: This section
More information2. Typical door size shall be 3-0 x 7-0. Wider doors should be used if required by function.
08 08 00 - OPENINGS A. General Requirements: 1. All window types shall be approved by the University Representative. Exterior window frames shall be aluminum. Steel-framed windows are prohibited for exterior
More information1. Section Steel Doors and Frames. 2. Section Flush Wood Doors 3. Section Aluminum Storefront Doors.
PROPOSED ALTERATIONS FOR REIMS PINECREST 124, LLC PINECREST, FLORIDA SECTION 08710 DOOR HARDWARE PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Mechanical door hardware for the following: B. Related
More informationSpecification Section Storefront Systems has been revised. Omit previously issued Storefront section.
December 28, 2018 ADDENDUM NO. 2 To: Re: Bidders Corey Pitts, NewQuest Properties This Addendum forms a part of the contract documents identified above. Acknowledge the receipt of this Addendum on the
More informationSECTION ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 4113 ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Section Includes: 1. Aluminum entrance doors and frames. 2. Glass infill panels. 3. Door hardware. B. Related Sections:
More informationAluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS
Aluminum Storefront Systems SERIES 200, 300 and 500 DOORS GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS This suggested guide specification has been developed using the current edition
More informationHardware. A. PRODUCT DATA: Submit manufacturer's technical information for each item of hardware.
Sections Included In This Standard: 1.1 General 1.2 Quality Assurance 1.3 Submittals 1.4 Keying 1.5 Product Handling 1.6 Job Conditions 1.7 Warranties 2.1 Scheduled Hardware PART I - GENERAL 1.1 GENERAL
More informationDoor Hardware
08 71 00 Door Hardware Submittals 1. Door Hardware Schedule: Prepared by or under the supervision of supplier, detailing fabrication and assembly of door hardware, as well as procedures and diagrams. Coordinate
More informationSECTION ALUMINUM WINDOWS
SECTION 08520 ALUMINUM WINDOWS PART 1 - GENERAL 1.01 SUMMARY A. Section includes: 1. Storefront systems and aluminum framed glass doors. 2. Hardware, fasteners, accessories, filler pieces, etc., required
More informationSECTION ALUMINUM ENTRANCES AND STOREFRONTS. A. Section Includes: Aluminum doors and window wall frames.
SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: Aluminum doors and window wall frames. B. Related Sections: 1. Section 08480 Balanced Doors 2. Section
More informationSECTION ACCORDION FOLDING PARTITIONS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 22 26.13 ACCORDION FOLDING PARTITIONS SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationBID # College Center EXTERIOR DOOR REPLACEMENT SECTION "C" TECHNICAL SPECIFICATIONS OWNER
BID # 16-15 College Center EXTERIOR DOOR REPLACEMENT SECTION "C" TECHNICAL SPECIFICATIONS OWNER Board of Trustees Middlesex County College 2600 Woodbridge Avenue P.O. Box 3050 Edison, New Jersey 08818-3050
More informationCITY OF FORT COLLINS BUILDING STANDARDS SPECIFICATIONS/DIV 8
CITY OF FORT COLLINS BUILDING STANDARDS SPECIFICATIONS/DIV 8 L. Division 8 - Doors and Windows 1. Windows 2. Doors a. Glazing shall be energy efficient (ie; Low-E) and have an insulated glass certification
More informationSECTION ALUMINUM-FRAMED STOREFRONTS
SECTION 08411 ALUMINUM-FRAMED STOREFRONTS PART 1 GENERAL 1.1 SUMMARY A. Includes But Not Limited To 1. Furnish and install aluminum storefront entry system, including hardware, glazing, and calking, as
More information6400 Series TRIPLE GLAZED THERMAL BREAK CHURCH WINDOWS America's finest custom windows MINIMUM 5 8" AIR SPACE 3 1 2" SCALE = FULL SIZE
Since 906 Series The Series is a heavy triple glazed church window incorporated into a " thermally broken frame. The thermal break is achieved with the use of Thermal Strip technology. Two different aluminum
More informationSECTION A1 SERIES 200, 300 AND 500 ENTRANCE DOORS
SECTION A1 SERIES 200, 300 AND 500 ENTRANCE DOORS TABLE OF CONTENTS Features... 3 Series 200 Entrance... 4 Series 300 Entrance... 5 Series 500 Entrance... 6 Miscellaneous Muntins and s... Specifications
More informationDESIGN AND CONSTRUCTION STANDARDS SPECIFICATION GUIDELINES
SECTION 08 70 00 - HARDWARE SCOPE OF WORK The Architect shall specify for the provision and installation of all items known commercially as builders hardware or door hardware. This shall include, but is
More informationADDENDUM NUMBER 1: Portsmouth City Boiler Plant Improvements Project Bid Proposal # Issued: May 23, 2011
ADDENDUM NUMBER 1: Portsmouth City Boiler Plant Improvements Project Bid Proposal #43-11 Issued: May 23, 2011 This Addendum forms part of the original document marked: Portsmouth City Hall Boiler Plant
More informationMARLIN WINDOWS, INC 3500 HC SERIES 3 3 8" SLIDING WINDOW PAGE 1
PAGE 1 SPECIFICATIONS GENERAL Sliding windows shall be Marlin series #3500-HC (thermally improved) as manufactured by Marlin windows, and shall conform to ANSI/AAMA 101-88 HS-HC40. Series #3500 shall have
More information1. Section Steel Doors and Frames. 2. Section Flush Wood Doors. 3. Section Overhead Coiling Doors.
SECTION 08710 FINISH HARDWARE PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division-1 Specification sections,
More informationSection A1 Table of Contents STANDARD ENTRANCES. Series 213 Narrow Stile Series 380 Medium Stile Series 500 Wide Stile
Section A1 Table of Contents STANDARD ENTRANCES Series 213 Narrow Stile Series 380 Medium Stile Series 500 Wide Stile Specifications - Series 213, 380 & 500...S1-S6 Features and Benefits... 1 Selection
More informationA NEW PRE-K BUILDING FOR BIG SPRING LAKE KINDERGARTEN SCHOOL FOR THE ALBERTVILLE CITY BOARD OF EDUCATION ALBERTVILLE, ALABAMA
McKee and Associates Architecture and Interior Design Addendum No. FOUR Date: 09.24.18 Project: A NEW PRE-K BUILDING FOR BIG SPRING LAKE KINDERGARTEN SCHOOL FOR THE ALBERTVILLE CITY BOARD OF EDUCATION
More informationCustom fabrication in two weeks or less, guaranteed.
Custom fabrication in two weeks or less, guaranteed. Ramco is the midwest Kawneer distributor and fabricator. ramcometals.com got lead times? Ramco offers custom fabrication in two weeks or less, guaranteed!
More informationSECTION DOOR HARDWARE
SECTION 087100 -DOOR HARDWARE PART 1- GENERAL 1.1 RELATED DOCUMENTS Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationSECTION DETAILS (MECHANICALLY ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSECTION ALL GLASS ENTRANCES. 1. Lock cylinders for tempered glass entrance doors are specified in Division 8 section Finished Hardware.
1 SECTION 08 4210 ALL GLASS ENTRANCES PART 1 - GENERAL 1.01 SUMMARY A. This section includes: 1. Vestibule doors matching entrance doors. 2. Sidelites. B. Related work in other sections: 1. Lock cylinders
More informationDIVISION 8 DOORS & WINDOWS
Section Title 08000 GENERAL INFORMATION 08100 HOLLOW METAL DOORS AND FRAMES 08110 Steel Doors and Frames Door Frames Doors 08200 WOOD AND PLASTIC DOORS 08250 Door Opening Assemblies 08300 SPECIAL DOORS
More informationCustom fabrication in two weeks or less, guaranteed.
Custom fabrication in two weeks or less, guaranteed. Ask us how Ramco can now fabricate hardware on all manufacturers blank doors in 2 weeks or less. ramcometals.com got lead times? Ramco offers custom
More informationms consultants, inc. 333 East Federal Street Youngstown, OH January 2, 2017 ADDENDUM NO. 3
ms consultants, inc. 333 East Federal Street Youngstown, OH 44503 January 2, 2017 ADDENDUM NO. 3 To The Plans and Specifications for: TO ALL BIDDERS: BOARDMAN FIRE DEPARTMENT ARCHITECT S PROJECT NO. 64-12952
More informationTender No Section St. James - Assiniboia Centennial Pool Fitness Facility Addition Page 1
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 SECTION INCLUDES.1 Extruded aluminum windows with fixed sash..2 Factory glazed..3 Perimeter sealant. 1.2 RELATED SECTIONS.1 Section 05500 - Metal Fabrications.2
More informationSECTION METAL FRAMED SKYLIGHT. A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system.
SECTION 08625 METAL FRAMED SKYLIGHT PART 1 GENERAL 1.01 SECTION INCLUDES: A. Engineering, preparation of fabrication drawings and structural calculations for the entire skylight system. B. Fabrication
More informationImpact-Resistant Entrances Series
ARCHITECTURAL PRODUCTS Impact-Resistant Entrances Manufacturer: Coral Architectural Products 3010 Rice Mine Road Tuscaloosa, AL. 35406 Voice: (800) 772-7737 Fax: (800) 443-6261 SECTION 08410 ALUMINUM ENTRANCES
More informationSERIES BAL-350 ALUMINUM OUTSWING ENTRANCE DOORS
SERIES BAL-350 ALUMINUM OUTSWING ENTRANCE DOORS Page 1 of 11 TABLE OF CONTENTS SECTION PAGE BALCONY DOORS GENERAL NOTES 3-5 BAL-350. TYPICAL ELEVATION 6 HEAD & TRANSOM TYPICAL DETAILS 7 SILL & JAMB TYPICAL
More informationGenius Movable Walls. October 2012
S t a n d a r d Pr o d u c t S t a t e m e n t o f L i n e Genius Movable Walls October 2012 2 Genius Movable Wall Table of Contents Doors & Openings A. Technical Specifications Pivot Door Specifications
More informationSECTION (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS
SECTION 08 41 13 (08410) - ALUMINUM-FRAMED ENTRANCES AND STOREFRONTS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Interior and Exterior Aluminum Storefront Framing, Doors, Door Frames, Lights, and
More informationGLASS WALL SPECIFICATIONS
GLASS WALL SPECIFICATIONS Series GA2 Ultra Acoustical, STC 45/46 Paired, Glass Wall PRODUCT OVERVIEW: Top Supported Center Stack Paired s Manually Operated Maximum Opening Height: 12' 2 [3.7m] Maximum
More informationSUBMITTAL PACKAGE CUSTOM HOLLOW METAL DOORS, FRAMES AND WINDOWS
Box 1101, 140 Coal St. Raton, NM 87740 Phone 575-445-2756 Fax: 575-445-2804 SUBMITTAL PACKAGE CUSTOM HOLLOW METAL DOORS, FRAMES AND WINDOWS DATE: PROJECT: LOCATION: CONTRACTOR: QUANITITY: DOORS: FRAMES:
More informationT SERIES WINDOW SPECIFICATIONS
SPECIFICATIONS Part 1 - GENERAL Scope The framing shall be Metro "T" Series fixed window system with thermal break as manufactured by Metro Glass. Furnish all materials, labour, and services for the complete
More information08710 FULL SPEC with Typical Hardware Sets GASKETING OF DOORS AND FRAMES ( )
08710 FULL SPEC with Typical Hardware Sets GASKETING OF DOORS AND FRAMES (02-02-09) You may find it easier to e-mail us your specification and we will e-mail it back to you with proposed changes highlighted
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Cast
More informationSECTION DOOR HARDWARE
SECTION 08710 PART 1 - GENERAL 1.1 CONDITIONS A. Conditions of the contract (General and Supplementary Conditions) and Division One General Requirements, govern the work of this section. B. This section
More informationPROCUREMENT AND CONTRACTING DOCUMENTS GROUP
PROCUREMENT AND CONTRACTING DOCUMENTS GROUP DIVISION 00 - PROCUREMENT AND CONTRACTING REQUIREMENTS 00 11 00 Notice To Bidders 00 21 00 Instructions To Bidders 00 22 00 Supplementary Instructions To Bidders
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 08 51 69.11 ALUMINUM STORM WINDOWS SPEC WRITER NOTES: 1. Delete between // // if not applicable to project. 2. Also delete any other item or paragraph not applicable
More informationFoldingAccess Series Aluminum Folding Door System
HORTON AUTOMATICS - ARCHITECTURAL SPECIFICATIONS, 1/2008 FoldingAccess Series 4-4200 Aluminum Folding Door System DIVISION 08 - OPENINGS SECTION 08 42 29.13 FOLDING AUTOMATIC ENTRANCES Specifier Note:
More informationSWING DOOR SPECIFICATION
SWING DOOR A1 Work included: Furnish all necessary materials, labour and equipment for the complete installation of aluminum entrance doors, door frames and hardware as detailed on the drawings and specified
More informationSECTION U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR
Page 1 of 6 SECTION 08 39 80 U.S. ALUMINUM SERIES BAL-350 HURRICANE RESISTANT BALCONY/TERRACE DOOR U.S. Aluminum has designed one of the most demanding air and water protection products, the BAL- 350 Small
More informationSeries Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 510 2-7 16 Heavy Commercial Projected Window Configurations Project-In Project-Out Casement Pivot Top-Hinged Fixed Series 510 retains an AAMA Architectural
More informationMCCARTY ARCHITECTS, P.A. POST OFFICE BOX 440 / 533 WEST MAIN STREET TUPELO, MS / FOR ANSWERS TO QUESTIONS CONTACT: JUSTIN HARRINGTON
ADDENDUM NUMBER FROM: MCCARTY ARCHITECTS, P.A. POST OFFICE BOX 0 / 533 WEST MAIN STREET TUPELO, MS 3880 / 3880 FOR ANSWERS TO QUESTIONS CONTACT: JUSTIN HARRINGTON PHONE: -8-00 PROJECT: ACADEMIC STUDENT
More informationColorado Mountain College Dillon Campus ADA Entry Vestibule
SECTION 08710- DOOR HARDWARE PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Door hardware for new, secure vestibule door. 2. Electro-mechanical devices and access control components as specified
More informationSeries B450 Guide Specification
Boyd Aluminum Manufacturing Company P.O. Box 1565 3248 E. Division Street Springfield, MO 65801-1565 800-737-2800 417-862-1232 fax boydaluminum.com STOREFRONT SERIES B450 Shear Block Air Infiltration:
More informationCOVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY)
COVER SHEET ELEVATION SHEET SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (MECHANICALLY ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (WELDED ASSEMBLY) SECTION DETAILS (DOOR ASSEMBLY)
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationPRODUCT SPECIFICATION THE 9500 SERIES FAMILY - SERIES 9502 / 9503 THERMALLY BROKEN ALUMINUM OUTSWING BALCONY DOOR
PART 1 - GENERAL 08 13 16 ALUMINUM DOORS (Outswing Aluminum-Framed Glass Doors) A high-quality thermally broken aluminum balcony outswing door designed for residential high rise construction. 1.1 SUMMARY
More informationDivision 08 - Openings
Division 08 - Openings 08 10 00 Doors and Frames 1. Doors to rooms storing high value items such as computers, scientific equipment, etc. shall have solid doors without vision panels and without adjacent
More informationDIVISION 8 DOORS AND WINDOWS
DIVISION 8 DOORS AND WINDOWS UCSC Campus Standards Handbook Metal Doors and Frames Standards 08100 1 SECTION 08100: METAL DOORS AND FRAMES I. GENERAL (not used) II. MATERIALS A. Interior door jambs: 16
More informationGLASS WALL SPECIFICATIONS
GLASS WALL SPECIFICATIONS Series GA1 Ultra Acoustical, STC 45/46, Omni, Glass Wall PRODUCT OVERVIEW: Top Supported Side Stack Individual, Omni-Directional s Manually Operated Maximum Opening Height: 12'
More informationFLUSHLINE ENTRANCES. Features
APRIL, 2012 FLUSHLINE ENTRANCES FEATURES 1 Features Flush appearance with face sheet of fiberglass reinforced polyester (FRP), acrylic modified polyester (AMP) or aluminum, that is captured on four sides
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS ************************************************************************** SECTION TABLE OF CONTENTS
USACE / NAVFAC / AFCEC / NASA UFGS-09 06 00 (May 2009) Change 1-11/13 ----------------------------- Preparing Activity: USACE Superseding UFGS-09 06 90 (April 2006) UNIFIED FACILITIES GUIDE SPECIFICATIONS
More informationSECTION MEDICATION CABINET. 1.1 SUMMARY A. Section Includes: 1. Medication cabinets with self-contained refrigerator and fixtures.
SECTION 12 35 70.21 MEDICATION CABINET SPEC WRITER NOTE: Delete text between // // not applicable to project. Edit remaining text to suit project. PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Medication
More informationAddendum No. 1 DELETE; TABLE OF CONTENTS "SHELVING & CLOSET HARDWARE" REVISION; DOOR HARDWARE - see attached revised Specifications.
SPUR DESIGN March 22,2012 Waldrop Construction, Inc. Construction Manager One Santa Fe Plaza, Suite 101 Oklahoma City, OK 73102 RE: ELLIS COUNTY MULTI-PURPOSE BUILDING Addendum No. 1 Item No. 1 CLARIFICATION;
More informationHURRICANE IMPACT-RESISTANT ENTRANCES
0 A Table of Contents t Storefro HURRICANE IMPACT-RESISTANT ENTRANCES Series 8 Narrow Stile Series 8 Medium Stile Section Page Specifications (8 and 8 Combined)... A... HS-6 Options and Limitations...
More informationSECTION WALL AND DOOR PROTECTION
PART 1 - GENERAL 1.1 DESCRIPTION: SECTION 10 26 00 WALL AND DOOR PROTECTION SPEC WRITER NOTE: Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable to
More informationSECTION FOLDING ALUMINUM FRAMED WALL SYSTEM
SECTION 08417 FOLDING ALUMINUM FRAMED WALL SYSTEM PART 1 GENERAL 1.1 SUMMARY A. Section includes: 1. Folding aluminum framed door system. 2. Door hardware. 3. Glass. 1.2 SYSTEM DESCRIPTION A. Aluminum-framed
More informationSECTION ALUMINUM STORM WINDOWS
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 51 69.11 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationINVITATION TO BID NUMBER ITB/PI-12/13-50 CONSTRUCTION OF CITRUS GERMPLASM INTRODUCTION PROGRAM BUILDING AND GREENHOUSE FOUNDATION / SLAB AND SITE WORK
ADDENDUM 3 TO: FROM: RE: Vendors Christie Hutchinson, Purchasing Director INVITATION TO BID NUMBER ITB/PI-12/13-50 CONSTRUCTION OF CITRUS GERMPLASM INTRODUCTION PROGRAM BUILDING AND GREENHOUSE FOUNDATION
More informationTechnical Data Sheet Signature 842
Technical Data Sheet Signature 842 Signature 800 Series Features & Options Standard Features Manually-operated paired-panel movable partition STC 43 or 47 with gypsum board faces STC 49, 52, 53, or 55
More informationSECTION MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN
SECTION 08350 MANUAL FOUR FOLD DOORS MODEL 38 DECORATIVE PANEL DESIGN PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationSECTION Coiling Doors and Grilles Model 4320
SECTION Coiling Doors and Grilles Model 4320 PART 1 GENERAL 1.1 SECTION INCLUDES A. Rolling Steel Grilles B. Guides and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared
More informationA NEW SCHOOL ATHENS BIBLE SCHOOL FOR THE PRESIDENT AND BOARD OF DIRECTORS ATHENS, ALABAMA
McKee and Associates Architecture and Interior Design Addendum No. TWO Date: 09.27.17 Project: A NEW SCHOOL ATHENS BIBLE SCHOOL FOR THE PRESIDENT AND BOARD OF DIRECTORS ATHENS, ALABAMA A2.1 GENERAL PROJECT
More informationSPECIFICATIONS...02-M3 TECHNICAL DATA...03-M3 TYPICAL DETAILS...04-M3 and 05-M3
0- Table of Contents SECTION PAGE SPECIFICATIONS...0- TECHNICAL DATA...0- TYPICAL DETAILS...0- and 0- Project: Private Condominiums, iami, FL Due to the diversity in state/provincial, local, and federal
More informationGUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM
1 GUIDE SPECIFICATION EXETER VERSA SHIELD SECURITY SCREEN SYSTEM 1.01 WORK INCLUDED PART 1: GENERAL A. Provide for all labor, equipment, materials, and services to furnish and install VERSA SHIELD Window
More informationDOOR HARDWARE
DIVISION 8 SECTION 08 71 00 DOORS AND WINDOWS PART 1 GENERAL 1.01 GENERAL REQUIREMENTS A. Include the General Conditions, Modifications to the General Conditions, and applicable parts of Division 01 00
More informationA. Access doors and frames are part of an access door and frame allowance.
SECTION 08 31 13 ACCESS DOORS AND FRAMES PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationASDA Aluminium Stockists and Distributors Association
ASDA Aluminium Stockists and Distributors Association Web: http://www.aaamsa.co.za Address: 1st Floor, Block 4 CMA Conference Center Office Park 2nd Road Midrand Registered Postal Address: PO Box 7861
More informationB. Glazing: Physically and thermally isolate glazing from framing members.
SECTION 08410 - ALUMINUM ENTRANCES AND STOREFRONTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSystem WV410 Storefront Window System
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com Manufacturer Of Architectural Configurations Project-out Casement-out The WV410 storefront vent system is designed to be field glazed and
More informationThe Metropolitan Sewer District of Greater Cincinnati
The Metropolitan Sewer District of Greater Cincinnati Sanitary Sewer No. 5174 & 5174A, CIP No. 2004-21 & 2005-10 Sycamore Creek WWTP Expansion & Upgrade Phase 3 and 4 Date Issued: 03/25/08 ADDENDUM NO.
More informationQuestions ARCHITECTURAL DESIGN ASSOCIATES, P.C O STREET, SUITE 105 LINCOLN, NE
ARCHITECTURAL DESIGN ASSOCIATES, P.C. 7501 O STREET, SUITE 105. 68510 December 29, 2016 Steve Arens 335 S 70th Lincoln, Nebraska -------------------------------------------------------------------------------------------------------------------------------------
More informationALL PROSPECTIVE CONTRACTORS, PLAN ROOMS AND SUPPLIERS
Architect: Studio 2H Design, LLC 1721 4 th Avenue North, Suite 101 Birmingham, Alabama 35203 (205) 264-9988 July 26, 2018 ADDENDUM NO. 5 UA Project No.: 712-17-1081 EDA Investment No.: 04-79-07154 B.C.
More informationHollow Metal Doors and Frames
University of New Hampshire University of New Hampshire Scholars' Repository Division 08 Openings Chapter 5 Technical Construction and Renovation Standards 1-25-2013 081113 - Hollow Metal Doors and Frames
More informationDETAILED METAL DOOR SPECIFICATION. UNIVERSITY CONTACT: Mark Golden, Supervisor of Structural Services (302)
DETAILED METAL DOOR SPECIFICATION UNIVERSITY CONTACT: Mark Golden, Supervisor of Structural Services (302) 831-8456 PART 1 GENERAL DOORS 1.01 GENERAL PROVISIONS I. The Drawings and General Provisions of
More informationSection A2 Table of Contents ALL GLASS ENTRANCES
Architectural Aluminum Entrances Storefronts Curtain Walls Impact-Resistant Systems Section A Table of Contents ALL GLASS ENTRANCES Specifications...S-S Swing Type A... - Swing Type F... - Swing Type P...
More informationELLISON BRONZE SECTION EXTRUDED ALUMINUM BALANCED DOOR ENTRANCES
ELLISON BRONZE SECTION 08 42 36 Section C EXTRUDED ALUMINUM BALANCED DOOR ENTRANCES Display hidden notes to specifier by using Tools / Options / View / Hidden Text PART 1 GENERAL 1.01 DESCRIPTION A. Work
More informationNOTE TO SPECIFIER: This section is based on the products of Solar Innovations, Inc., which is located at:
SECTION #57313 BY SOLAR INNOVATIONS, INC. NOTE TO SPECIFIER: This section is based on the products of Solar Innovations, Inc., which is located at: 31 Roberts Road Pine Grove, PA 17963 Phone 800-618-0669;
More informationCardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS
Cardinal Commercial Products ALUMINUM STOREFRONT SYSTEM SERIES CF450 GUIDE SPECIFICATIONS SECTION 08410 ALUMINUM ENTRANCES AND STOREFRONT SYSTEMS This suggested guide specification has been developed using
More informationSeries 890-I Equa-Vu Heavy Commercial Projected Window
Windows Curtain Walls Entrances Storefronts Series 890-I Equa-Vu 3 1 2 Heavy Commercial Projected Window Configurations Project-In Casement Inswing Fixed Series 890-I retains an AAMA Architectural Grade
More informationACOUSTI-CLEAR AUTOMATIC SERIES TECHNICAL DATA
Paired panel system Acoustically rated glass wall system Automatic seal system Hinged together in groups of two, facilitating quick, easy setup Each panel is supported by a single carrier Ideal for straight-line
More information4.1.3 Project Manual
4.1.3 Project Manual (*Section requires Filed Sub-Bid) PROCUREMENT AND CONTRACTING REQUIREMENTS GROUP Division 00 Procurement and Contracting Requirements Section 00 01 03 Project Directory Section 01
More informationPIP ARS08710 Standard Steel Door Hardware Supplier Specification
April 2018 Architectural PIP ARS08710 Standard Steel Door Hardware Supplier Specification PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities,
More informationLEGENDS/SYMBOLS INDEX SHEET NUMBER ABBREVIATIONS PROJECT NAME AND ADDRESS 2/3/12 1ST. SUBMISSION ARCHITECTURAL DRAWINGS: DATED 08/05/11
LEGENDS/SYMBOLS FINISHED WOOD PLYWOOD DIMENSION LUMBER BATT INSULATION FACE BRICK GROUT RIGID INSULATION GLAZED TILE CUT STONE MARBLE CONCRETE ACOUSTICAL CEILING CONCRETE BLOCK SHIM PACK STEEL IN SECTION
More informationSECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Doors B. Track and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening in masonry.
More informationAll Vendors Bidding on The College of New Jersey Window Replacement at Maintenance Building Project. The College of New Jersey. Date: May 15, 2018
To: All Vendors Bidding on The College of New Jersey Window Replacement at Maintenance Building Project From: The College of New Jersey Date: May 15, 2018 ADDENDUM NO. 1 ISSUE DATE: May 15, 2018 REFERENCE:
More informationSECTION DOOR HARDWARE
SECTION 08710 PART 1 - GENERAL 1.1 CONDITIONS A. Conditions of the contract (General and Supplementary Conditions) and Division One General Requirements, govern the work of this section. B. This section
More informationHD-Slide Series 2001 Heavy Duty Aluminum Sliding Door System with Electric Belt Drive Operator
HORTON AUTOMATICS - ARCHITECTURAL SPECIFICATIONS, 1/2008 HD-Slide Series 2001 Heavy Duty Aluminum Sliding Door System with Electric Belt Drive Operator DIVISION 08 - OPENINGS SECTION 08 42 29.23 SLIDING
More information