TECHNICAL DESCRIPTION OF UNIT Nos. 12, 22, 32, 42. reconstructed units

Transcription

1 DESCRIPTION material/type/modification status EXTERIOR WINDOWS scuntion windows INTERIOR DOORS entrance door to unit historical replicas - wooden frame, 1x thermal insulated double glazing and 1x simple glazing historical replicas - fire resistant security doors - wooden single door in casing frame doors inside unit casing non-rebated door mm, CPL white HEATING central gas boiler room heater - smooth white WATER MAINS cold water pipes PP pipes of the appropriate size, thermal insulation warm water pipes PP pipes of the appropriate size, thermal insulation SEWAGE sewage pipes PP HT pipes ELECTRICAL MAINS electrical wiring CYKY cable television antenna DVBT/FM and SAT signal wiring, coaxial cable, TV/FM/SAT socket telephone lines UTP cat 5e cables, double SKS outlet data lines cable protective casing + coaxial cables building phone lines video telephone device, cable FLOOR COVERING front hall, bathroom, WC ceramic 200x200 mm tiles living rooms floor with wooden treading layer - rustic oak, "triple board" BATHROOM and WC fittings, water taps Jika Cubito, single-lever tap shower stall: shower tray from cast marble, glass partition walls ceramic 200x200 mm tiles SURFACE TREATMENT plaster stucco cement-lime plaster, paint repaired in 2017 ceilings gypsum board ceiling, paint MEASUREMENT OF ENERGY CONSUMPTION drinking water water meter in unit, remote reading electricity unit electric meter in area of stairwell heat meter in unit, remote reading * The right to change materials, configuration and dates is reserved. Explanation of statuses: TECHNICAL DESCRIPTION OF UNIT Nos. 12, 22, 32, 42 Dalimilova 925/11, Prague 3 - Rezidence U Kronikáře reconstructed units "" - Indicates the delivery or implementation of entirely new structures, elements, wiring, items, etc. as part of the structural modifications of the units and the common parts of the building. The guarantee pursuant to the relevant paragraph of the Purchase Agreement applied to the parts of the units with the designation of "new" with a specification of the year of implementation or acquisition. "original" - indicates the original condition of the specified structure, element, wiring, fittings of the unit, on which no repairs, modifications, or revisions have taken place, there have been no interventions on them of any kind and they can show deviations from current standards or norms. "revision in 2017" - There was only a review on the system, wiring, device or equipment in question in the given year to guarantee its safe functionality. A guarantee pursuant to the relevant paragraph of the Purchase Agreement applies to these parts of the units with the "revision" designation. "repaired in 2017" - repairs guarnateeing the status after the performance of work necessary for the renewal/improvement of the appearance and primarily to ensure the correct functionality. The repairs take place in the form of local or full surface treatment, in the form of the adjustment, addition or exchange or some of the elements. During the repairs the functions or visual or other parameters corresponding to the status of "New" are never reached. Notes to the Technical Description / Standards (Description of selected structures, elements, materials, items and systems) Flat and Common parts of block of flats:

2 Exterior doors and windows - due to external conditions (temperature changes, aging of construction, loading, etc.) there can be an imperceptible deviation of the windows, i.e. "slack", which is exhibited by abutting on the frame, a lack of sealing or difficulty in opening the window. In this case this is considered to be a frequent phenomenon, which is not caused by a product or assembly defect and thus cannot be claimed. In the event that such a phenomenon arises, it is necessary to ensure the adjustment of the window without great delay. The service is a matter of regular maintenance and is performed by the client at its own expense. The functional joints of the original windows may not seal completely, leading to a larger than usual amount of external air leaking into the interior. Interior and entrance doors - if there is "slack" in the doors, the situation and approach is the same as in the case of "Exterior doors and windows" (see above) - the adjustment of the door is provided by the client at its own expense. During the assembly of new doors on the original frames, the door may not sit well on the frame, leading to the more difficult closing or locking of the door. Floor treading layer - In the case of "New" this is only the delivery of floor coverings and not the complete implementation of the floor. Thus the contractor is only responsible for the quality of the assemby and the material of the treading layer. In the case of the original treading layer there may be some sag, some manifestations of noise (creaches, etc.) and/or the imperfect sealing of the joints of the individual flooring elements. Walls, ceilings - in light of the historical character of the building, it is necessary to expect deviations from the parameters prescribed by the current valid norms (ČSN). Primarily the flatness and verticality of the structure, the perpendicularity of the structural joints, etc. may not be maintained. Due to the load the original wooden load-bearing ceiling structures can be bent and can also lead to the uneveness of the floor's treading layer. Acoustics - the fulfilment of acoustic standards cannot be guaranteed for walls between flats and floor structures, the structure or the actual construction of which has not been altered, except for the treading layer. This applies primarily to the damping of impact noise and sound-transmission loss. The guarantee does not apply to the characteristics of the original dividing structures. Underground floors of the block of flats - in light of the historical character of the building and its technical design, it is necessary to point out the possibility of the permeation of moisture through the circumference wall and the floor. Balconies, terraces - for the original structures, where the exchange of the treading layers has not been performed, some places with an insufficient drainage of rain water can be expected. These phenomena are caused primarily by the poor weathered pointing of the horizontal structure. Façade - climatic phenomena (rain, changes of temperatures,...) can lead to the occurrence of microfissures and the disruption of the plaster, primarily in the places under the greatest strain, e.g. the plinths of the circumference wall. Connection of structures on the exterior of the building - Connecting two or more structures can, in time, lead to the creation of smaller or larger cracks in the connections/joints. This phenomenon is caused by the influence of different physical characteristics of the materials and changes in climatic conditions. The creation of joints usually has no effect on the technical characteristics or safety of the use of the building.

3 DESCRIPTION material/type/modification status EXTERIOR WINDOWS EURO windows scuntion windows VÝPLNĚ VNITŘNÍCH OTVORŮ entrance door to unit entrance doors to unit no. 13 wooden windows and balcony doors - thermal insulated double glazing historical replicas - wooden frame, 1x thermal insulated double glazing and 1x simple glazing historical replicas - fire resistant security doors - wooden single door in casing frame historical - fire resistant security doors - wooden double doors in casing frame renovated in 2017 doors inside unit casing non-rebated door mm, CPL white HEATING central gas boiler room heater - smooth white WATER MAINS cold water pipes PP pipes of the appropriate size, thermal insulation warm water pipes PP pipes of the appropriate size, thermal insulation SEWAGE sewage pipes PP HT pipes ELECTRICAL MAINS electrical wiring CYKY cable television antenna DVBT/FM and SAT signal wiring, coaxial cable, TV/FM/SAT socket telephone lines UTP cat 5e cables, double SKS outlet data lines cable protective casing + coaxial cables building phone lines video telephone device, cable FLOOR COVERING front hall, bathroom, WC ceramic 200x200 mm tiles living rooms floor with wooden treading layer - rustic oak, "triple board" BATHROOM and WC fittings, water taps Jika Cubito, single-lever tap shower stall: shower tray from cast marble, glass partition walls ceramic 200x200 mm tiles SURFACE TREATMENT plaster stucco cement-lime plaster, paint repaired in 2017 ceilings gypsum board ceiling, paint MEASUREMENT OF ENERGY CONSUMPTION drinking water water meter in unit, remote reading electricity unit electric meter in area of stairwell heat meter in unit, remote reading BALCONIES TECHNICAL DESCRIPTION OF UNIT Nos. 13, 23, 33, 43 Dalimilova 925/11, Prague 3 - Rezidence U Kronikáře reconstructed units floor, railing ceramic tiling, metal railing balcony fittings electrical outlet, lights * The right to change materials, configuration and dates is reserved. Explanation of statuses: "" - Indicates the delivery or implementation of entirely new structures, elements, wiring, items, etc. as part of the structural modifications of the units and the common parts of the building. The guarantee pursuant to the relevant paragraph of the Purchase Agreement applied to the parts of the units with the designation of "new" with a specification of the year of implementation or acquisition. "original" - indicates the original condition of the specified structure, element, wiring, fittings of the unit, on which no repairs, modifications, or revisions have taken place, there have been no interventions on them of any kind and they can show deviations from current standards or norms. "revision in 2017" - There was only a review on the system, wiring, device or equipment in question in the given year to guarantee its safe functionality. A guarantee pursuant to the relevant paragraph of the Purchase Agreement applies to these parts of the units with the "revision" designation. "repaired in 2017" - repairs guarnateeing the status after the performance of work necessary for the renewal/improvement of the appearance and primarily to ensure the correct functionality The repairs take place in the form of local or full surface treatment in the

4 appearance and primarily to ensure the correct functionality. The repairs take place in the form of local or full surface treatment, in the form of the adjustment, addition or exchange or some of the elements. During the repairs the functions or visual or other parameters corresponding to the status of "New" are never reached. Notes to the Technical Description / Standards (Description of selected structures, elements, materials, items and systems) Flat and Common parts of block of flats: Exterior doors and windows - due to external conditions (temperature changes, aging of construction, loading, etc.) there can be an imperceptible deviation of the windows, i.e. "slack", which is exhibited by abutting on the frame, a lack of sealing or difficulty in opening the window. In this case this is considered to be a frequent phenomenon, which is not caused by a product or assembly defect and thus cannot be claimed. In the event that such a phenomenon arises, it is necessary to ensure the adjustment of the window without great delay. The service is a matter of regular maintenance and is performed by the client at its own expense. The functional joints of the original windows may not seal completely, leading to a larger than usual amount of external air leaking into the interior. Interior and entrance doors - if there is "slack" in the doors, the situation and approach is the same as in the case of "Exterior doors and windows" (see above) - the adjustment of the door is provided by the client at its own expense. During the assembly of new doors on the original frames, the door may not sit well on the frame, leading to the more difficult closing or locking of the door. Floor treading layer - In the case of "New" this is only the delivery of floor coverings and not the complete implementation of the floor. Thus the contractor is only responsible for the quality of the assemby and the material of the treading layer. In the case of the original treading layer there may be some sag, some manifestations of noise (creaches, etc.) and/or the imperfect sealing of the joints of the individual flooring elements. Walls, ceilings - in light of the historical character of the building, it is necessary to expect deviations from the parameters prescribed by the current valid norms (ČSN). Primarily the flatness and verticality of the structure, the perpendicularity of the structural joints, etc. may not be maintained. Due to the load the original wooden load-bearing ceiling structures can be bent and can also lead to the uneveness of the floor's treading layer. Acoustics - the fulfilment of acoustic standards cannot be guaranteed for walls between flats and floor structures, the structure or the actual construction of which has not been altered, except for the treading layer. This applies primarily to the damping of impact noise and sound-transmission loss. The guarantee does not apply to the characteristics of the original dividing structures. Underground floors of the block of flats - in light of the historical character of the building and its technical design, it is necessary to point out the possibility of the permeation of moisture through the circumference wall and the floor. Balconies, terraces - for the original structures, where the exchange of the treading layers has not been performed, some places with an insufficient drainage of rain water can be expected. These phenomena are caused primarily by the poor weathered pointing of the horizontal structure. Façade - climatic phenomena (rain, changes of temperatures,...) can lead to the occurrence of microfissures and the disruption of the plaster, primarily in the places under the greatest strain, e.g. the plinths of the circumference wall. Connection of structures on the exterior of the building - Connecting two or more structures can, in time, lead to the creation of smaller or larger cracks in the connections/joints. This phenomenon is caused by the influence of different physical characteristics of the materials and changes in climatic conditions. The creation of joints usually has no effect on the technical characteristics or safety of the use of the building.

5 TECHNICAL DESCRIPTION OF UNIT Nos. 51 a 52 Dalimilova 925/11, Prague 3 - Rezidence U Kronikáře reconstructed units DESCRIPTION material/type/modification status EXTERIOR WINDOWS atelier windows metal, swivel fields - thermal insulated double glazing skylights wooden swivel windows - thermal insulated double glazing glazed walls set of large metal sliding (lifting) windows, thermal insulated double glazing INTERIOR DOORS entrance door to unit replicas of originals - fire resistant security doors - wooden single door in casing frame doors inside unit casing non-rebated door mm, CPL white HEATING central gas boiler room heater - smooth white, floor convectors WATER MAINS cold water pipes PP pipes of the appropriate size, thermal insulation warm water pipes PP pipes of the appropriate size, thermal insulation SEWAGE sewage pipes PP HT pipes ELECTRICAL MAINS electrical wiring CYKY cable television antenna DVBT/FM and SAT signal wiring, coaxial cable, TV/FM/SAT socket telephone lines UTP cat 5e cables, double SKS outlet data lines cable protective casing + coaxial cables building phone lines video telephone device, cable AIR CONDITIONING multisplit system separate exterior condensation unit for unit, interior wall-mounted cooling unit, smooth white FLOOR COVERING, STAIRS front hall, bathroom, WC ceramic 200x200 mm tiles, including shower stall living rooms floor with wooden treading layer - rustic oak, "one board" storage space Oriented strand boards stairs attic fold-up stairs with a wooden ladder BATHROOM and WC fittings, water taps Laufen Pro S, Laufen City Pro, glass shower partition walls ceramic 200x200 mm tiles SURFACE TREATMENT plaster stucco cement-lime plaster, paint repaired in 2017 ceilings gypsum board, paint; wooden truss elements, paint MEASUREMENT OF ENERGY CONSUMPTION drinking water water meter in unit, remote reading electricity unit electric meter in area of stairwell heat meter in unit, remote reading TERRACE floor, railing ceramic tiling on disks, steel railing on ledge fittings electrical outlet, lights, water pipe * The right to change materials, configuration and dates is reserved. Explanation of statuses: "" - Indicates the delivery or implementation of entirely new structures, elements, wiring, items, etc. as part of the structural modifications of the units and the common parts of the building. The guarantee pursuant to the relevant paragraph of the Purchase Agreement applied to the parts of the units with the designation of "new" with a specification of the year of implementation or acquisition. "original" - indicates the original condition of the specified structure, element, wiring, fittings of the unit, on which no repairs, modifications, or revisions have taken place, there have been no interventions on them of any kind and they can show deviations from current standards or norms.

6 "revision in 2017" - There was only a review on the system, wiring, device or equipment in question in the given year to guarantee its safe functionality. A guarantee pursuant to the relevant paragraph of the Purchase Agreement applies to these parts of the units with the "revision" designation. "repaired in 2017" - repairs guarnateeing the status after the performance of work necessary for the renewal/improvement of the appearance and primarily to ensure the correct functionality. The repairs take place in the form of local or full surface treatment, in the form of the adjustment, addition or exchange or some of the elements. During the repairs the functions or visual or other parameters corresponding to the status of "New" are never reached. Notes to the Technical Description / Standards (Description of selected structures, elements, materials, items and systems) Flat and Common parts of block of flats: Exterior doors and windows - due to external conditions (temperature changes, aging of construction, loading, etc.) there can be an imperceptible deviation of the windows, i.e. "slack", which is exhibited by abutting on the frame, a lack of sealing or difficulty in opening the window. In this case this is considered to be a frequent phenomenon, which is not caused by a product or assembly defect and thus cannot be claimed. In the event that such a phenomenon arises, it is necessary to ensure the adjustment of the window without great delay. The service is a matter of regular maintenance and is performed by the client at its own expense. The functional joints of the original windows may not seal completely, leading to a larger than usual amount of external air leaking into the interior. Interior and entrance doors - if there is "slack" in the doors, the situation and approach is the same as in the case of "Exterior doors and windows" (see above) - the adjustment of the door is provided by the client at its own expense. During the assembly of new doors on the original frames, the door may not sit well on the frame, leading to the more difficult closing or locking of the door. Floor treading layer - In the case of "New" this is only the delivery of floor coverings and not the complete implementation of the floor. Thus the contractor is only responsible for the quality of the assemby and the material of the treading layer. In the case of the original treading layer there may be some sag, some manifestations of noise (creaches, etc.) and/or the imperfect sealing of the joints of the individual flooring elements. Walls, ceilings - in light of the historical character of the building, it is necessary to expect deviations from the parameters prescribed by the current valid norms (ČSN). Primarily the flatness and verticality of the structure, the perpendicularity of the structural joints, etc. may not be maintained. Due to the load the original wooden load-bearing ceiling structures can be bent and can also lead to the uneveness of the floor's treading layer. Acoustics - the fulfilment of acoustic standards cannot be guaranteed for walls between flats and floor structures, the structure or the actual construction of which has not been altered, except for the treading layer. This applies primarily to the damping of impact noise and sound-transmission loss. The guarantee does not apply to the characteristics of the original dividing structures. Underground floors of the block of flats - in light of the historical character of the building and its technical design, it is necessary to point out the possibility of the permeation of moisture through the circumference wall and the floor. Balconies, terraces - for the original structures, where the exchange of the treading layers has not been performed, some places with an insufficient drainage of rain water can be expected. These phenomena are caused primarily by the poor weathered pointing of the horizontal structure. Façade - climatic phenomena (rain, changes of temperatures,...) can lead to the occurrence of microfissures and the disruption of the plaster, primarily in the places under the greatest strain, e.g. the plinths of the circumference wall. Connection of structures on the exterior of the building - Connecting two or more structures can, in time, lead to the creation of smaller or larger cracks in the connections/joints. This phenomenon is caused by the influence of different physical characteristics of the materials and changes in climatic conditions. The creation of joints usually has no effect on the technical characteristics or safety of the use of the building.