04.00 GENERAL SECONDARIES & SERVICES SECONDARY AND SERVICE CABLE SPLICES INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS 04.
|
|
- Amberlynn Gallagher
- 6 years ago
- Views:
Transcription
1 4. GENERAL SECONDARIES & SERVICES 4.- TIE COLOR CODING 4.-6 SECONDARY AND SERVICE CABLE SPLICES 4.- INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS POLE ATTACHMENTS POLE ATTACHMENT DEVICES NEUTRAL POLE ATTACHMENTS SECONDARY POLE ATTACHMENTS SECONDARIES SECONDARY ATTACHMENTS 4.4- SECONDARY ATTACHMENTS SECONDARY ATTACHMENTS SERVICES SERVICE ATTACHMENT METHODS SERVICE TAPS MIDSPAN SERVICE TAPS /6/ CECCONI GUINN ELKINS REVISED BY CK'D APPR. SECTION 4 - SECONDARY CONSTRUCTION, OVERHEAD TABLE OF CONTENTS 4.-A R
2 GENERAL. THE NEUTRAL SHALL BE COMMON TO BOTH PRIMARY AND SECONDARY CIRCUITS ON WYE SYSTEMS. THE NEUTRAL SHALL BE MULTI-GROUNDED.. THE NEUTRAL CONDUCTOR SHALL ALWAYS BE IN THE TOP POSITION ON AN OPEN-WIRE SECONDARY CIRCUIT. SIZING OF SECONDARY CONDUCTORS WILL DEPEND ON THE AMOUNT OF LOAD, THE TYPE OF LOAD (SUCH AS MOTORS, ETC.), AND THE VOLTAGE DROP.. ALL SERVICE CONDUCTORS WILL BE OF COVE ALUMINUM. THE REQUI SIZE, SHALL BE SPECIFIED BY THE ENGINEER. 4. THE SERVICE ENTRANCE LOCATION WILL BE DETERMINED BY THE COMPANY AND MUST BE AGREED TO BY THE CUSTOMER. CUSTOMER'S REQUESTS FOR NON-STANDARD LOCATIONS FREQUENTLY REQUIRE AN ADDITIONAL CHARGE. 5. FOR THREE-PHASE FOUR WIRE DELTA SECONDARY CABLE AND SERVICES, THE PHASE CONDUCTOR WITH THE MOST NUMBER OF RAISED RIBS WILL BE THE HIGH (8 VOLT) PHASE. 6. USE INSULINKS OR INSTALL COVERS OVER SECONDARY CABLE OR SERVICE CABLE PHASE CONNECTORS. 7. STREETLIGHT CIRCUITS ARE TO BE CONSIDE AS SECONDARY. 8. BEFORE CUTTING THE LACING WIRE ON AERIAL SECONDARY CABLE, BIND THE LACING WITH SEVERAL TURNS OF SCRAP LACING WIRE. 9. TO DEADEND THE PHASE CONDUCTORS OF AERIAL SECONDARY CABLE WHILE ALLOWING NEUTRAL TO CONTINUE ON, FIRST TAPE THE ENDS OF THE PHASE CONDUCTOR THEN BEND THEM BACK AND SECURE WITH SEVERAL WRAPS OF THE BINDING WIRE. COVER ENDS IF NOT IN USE.. IF THERE IS NO PRIMARY ON THE POLE, RUN SECONDARY TO THE TOP OF THE POLE WITH THE STANDARD 5" CLEARANCE. LIMIT FOR ALUMINUM CABLES NOT REQUIRING GUYING WIRE SIZE CODE NAME **SPAN LENGTH #6 DUPLEX SERVICE VISZLA #4 DUPLEX SECONDARY # TRIPLEX SERVICE #/ TRIPLEX SERVICE/SECONDARY #4/ TRIPLEX SERVICE 5/5 TRIPLEX SERVICE #/ QUADRUPLEX SECONDARY #4/ QUADRUPLEX SECONDARY 6.4/5 QUADRUPLEX SERVICE WHIPPET SOLASTER #/ DUPLEX SECONDARY NO CODE NAME SANDCRAB NO CODE NAME *NO CODE NAME GALLEY NO CODE NAME *NO CODE NAME 95' 5' 5' ' ' 5 QUADRUPLEX SERVICE *NO CODE NAME 4' * WIRE SIZE CUSTOM MADE IN FIELD ** BASED ON LB. CUSTOMER MAST TENSION LIMIT AS INDICATED IN THE REQUIREMENTS FOR ELECTRIC SERVICE AND METER INSTALLATIONS MANUAL. 7' 5' 9' 6' 4' 9/4/5 LOOSIER BURLISON ADCOCK /8/ BURLISON ADCOCK REVISED BY CK'D APPR. SECONDARIES & SERVICES DEC DEM DEP DEF X 4.-
3 COMPATIBLE UNIT CATALOG NUMBER DESCRIPTION CHANCE PREFORMED NEUSPTIEN4ALF 46 FORMED SPOOL TIE #4 ALUMINUM NEUSPTIENALF FORMED SPOOL TIE # ALUMINUM NEUSPTIEALF 466 FORMED SPOOL TIE #/ ALUMINUM STIEFN4ALF 4 SIDE TIE F NECK #4 ALUMINUM STIEFNALF 58 SIDE TIE F NECK # ALUMINUM STIEFALF 46 SIDE TIE F NECK / ALUMINUM STIEF6ALF 49 SIDE TIE F NECK 6 KCM ALUMINUM - PURPLE STIEF795ALF 44 SIDE TIE F NECK 795 KCM ALUMINUM GREEN GREEN NOTE: COLOR CODE IN CHART DESIGNATES WIRE SIZE INSULATOR SIZE "F' NECK- CONDUCTOR SIZE IDENTITY TAPE CONDUCTOR SIZE CONDUCTOR SIZE IDENTITY TAPE INSULATOR SIZE "F' NECK- /6/ BURLISON GUINN REVISED BY CK'D ELKINS APPR. TIE COLOR CODING 4.-6 R
4 SEMI-TENSION SLEEVE INSULATED SERVICE ENTRANCE COMPRESSION CONNECTOR; SEE DWG 4.- FOR INSTALLATION INSTRUCTIONS AND CONNECTOR INFORMATION 6" 6" TRIPLEX CABLE SPLICE SEMI-TENSION SLEEVES FOR SERVICE NEUTRALS CATALOG NUMBER CONDUCTOR SIZE 4459 #6 ACSR OR ALLOY 446 #4 ACSR OR ALLOY 4464 # ACSR OR ALLOY 4466 #/ ACSR OR ALLOY INSULATED SERVICE ENTRANCE COMPRESSION CONNECTOR; SEE DWG 4.- FOR INSTALLATION INSTRUCTIONS AND CONNECTOR INFORMATION SEMI-TENSION SLEEVE 6" 6" 6" QUADRUPLEX CABLE SPLICE. WHEN SPLICING NEUTRAL, CUT OFF ENOUGH CONDUCTOR TO ASSURE A LOOSE WRAP OF PHASE CONDUCTORS AT SPLICE.. USE "BG" GROOVE OF BURNDY TOOL, OR EQUIVALENT TOOL WITH DIE FOR 5/8" SLEEVES. USE 84 DIE ON 4/ SLEEVE.. CLEAN CONDUCTORS BY WIRE BRUSHING. 4. FOR DETAILS OF INSULATED COMPRESSION CONNECTOR INSTALLATION SEE DWG "NEW" TRIPLEX OR QUADRUPLEX SECONDARIES AND SERVICES MAY CONTAIN A MAXIMUM OF ONE SPLICE PER SPAN. "REPAIR" TRIPLEX OR QUADRUPLEX SECONDARIES AND SERVICES MAY CONTAIN A MAXIMUM OF TWO SPLICES PER SPAN. 6. PHASE CONDUCTORS SHALL BE POSITIONED SUCH THAT CONTACT WITH THE NEUTRAL SLEEVE WILL NOT OCCUR. 6/6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SECONDARY AND SERVICE CABLE SPLICES 4.- R
5 NOTE STRIP LENGTH NOTE NOTE INSULATED COMPRESSION CONNECTOR SIZE TABLE PGN CN CONDUCTOR SIZE END MARKINGS END COLOR CONDUCTOR SIZE END COLOR 85 6 BLUE 6 BLUE BLUE BLUE /O 4 8 /O 8 /O I/O 9498 / / GRAY 956 /O / BLACK 956 /O 4/ PINK 95 4/O PINK 4/O PINK. STRIP INSULATION ON EACH CONDUCTOR FOR LENGTH SHOWN BY ARROWS ON SIDE OF CONNECTOR, CLEAN CONDUCTOR BY WIRE BRUSHING.. INSERT CONDUCTORS THROUGH CAPS ON EACH END UNTIL THEY HIT THE CENTER STOP.. MAKE THREE COMPRESSIONS ON EACH END. ROTATE TOOL SO THAT CRIMPS DO NOT LINE UP. USE "BG" GROOVE OF BURNDY TOOL, OR EQUIVALENT TOOL WITH DIE FOR 5/8" SLEEVES. REMOVE END CAPS WHEN INSTALLED ON BARE NEUTRAL. 4. INSULATED COMPRESSION CONNECTOR IS TO BE USED FOR NON-TENSION JOINTS ONLY. NO TAPING OR ADDITIONAL INHIBITOR IS REQUI. SEE 4.- FOR SERVICE DROP CABLE SPLICE. 7/8/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS 4.-
6 INSULATOR, SECONDARY SPOOL INSULATOR, SECONDARY RACK FOR TANGENT POLE NEUTRAL SUPPORT AND OPEN-WIRE SECONDARY SUPPORT (ANGLES TO 5 DEGREES) FOR ANGLE POLE NEUTRAL SUPPORT AND OPEN-WIRE SECONDARY DEAD ENDS BILL OF MATERIALS MACRO UNIT - CU ITEM NO. COMPATIBLE UNIT ISPLF NSSBF ISPLF NSSCF QTY REQ'D CATALOG NUMBER QTY PER CU DESCRIPTION INSULATOR, SPOOL, " BOLT, SPOOL, 5/8 X, GALV WASHER, SPRING, COIL, STEEL, FOR 5/8" BOLT, GALV. WASHER, SQUARE, -/4", FLAT, /6" HOLE, GALV. INSULATOR, SPOOL, " BRACKET, ONE, WIRE, NO, INSULATOR, GALVANIZED BOLT, MACH, SQ, NUT, 5/8"X" WASHER, SQUARE, -/4", SQUARE, FLAT, /6", HOLE, GALV.. FOR FACTORY FORMED TIE INFORMATION, SEE.4-9. /7/4 McCONNELL DANNA ADCOCK /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. POLE ATTACHMENT DEVICES DEC DEM DEP DEF X 4.-
7 TANGENT, SPOOL TANGENT, MESSENGER CLAMP SLACK SPAN 4 5 SCTAN(WIRE SIZE)FM AERIAL CABLE ONLY AERIAL CABLE OR BARE CONDUCTOR DEADEND, RACK ANGLE, RACK 6 6 4" 4" GUY ATTACHMENT 5 GUY ATTACHMENT DEADEND, EYEBOLT 7 8 4" GUY ATTACHMENT AERIAL CABLE OR BARE CONDUCTOR. GUYED FULL TENSION OR UNGUYED SLACK SPAN MACRO UNIT SCTAN_FM (VARIES WITH WIRE SIZE) - SCSLKSP_FM (VARIES WITH WIRE SIZE) SCDERACK_FM (VARIES WITH WIRE SIZE) SCANG_FM (VARIES WITH WIRE SIZE) - CU ITEM NO COMPATIBLE UNIT ISPLF NSSBF NEUSPTIE_F ISPLF NSSBF NEUDEGRIP_F ISPLF NEUDEGRIP_F NSSCF ISEYEBOLT58_F DECLMP_C QTY REQ'D BILL OF MATERIALS DESCRIPTION INSULATOR SPOOL NEUTRAL AND SECONDARY SPOOL BOLT INCH FORMED SPOOL TIE (VARIES WITH WIRE SIZE) 4 NEUMESCLMP_F MESSENGER CLAMP (VARIES WITH SIZE) INSULATOR SPOOL NEUTRAL AND SECONDARY SPOOL BOLT INCH DEADEND GRIP (VARIES WITH WIRE SIZE) INSULATOR SPOOL DEADEND GRIP (VARIES WITH WIRE SIZE) 5 6 NSSCF NEUTRAL AND SECONDARY SPOOL CLEVIS ISPLF INSULATOR SPOOL NEUSPTIE_F FORMED SPOOL TIE (VARIES WITH WIRE SIZE) NEUTRAL AND SECONDARY SPOOL CLEVIS INSULATOR SUPPORT EYEBOLT, 5/8" X REQ'D LENGTH (VARIES W/ WIRE SIZE) DEADEND CLAMP (VARIES WITH WIRE SIZE). SEE 4.- FOR POLE ATTACHMENT DEVICES.. FOR FACTORY FORMED TIE INFORMATION, SEE // McCONNELL DANNA ADCOCK /5/ McCONNELL DANNA ADCOCK /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. NEUTRAL POLE ATTACHMENTS 4.-
8 OPEN WIRE, TANGENT, SPOOL OPEN WIRE, DEADEND, RACK SEE NOTE 4" " " " ". DEADEND CLAMP FOR NEUTRAL MAY BE USED IN LIEU OF THE CLEVIS, SPOOL AND PRE-FORMED GRIP. SEE.-4 FOR DEADEND CLAMP ASSEMBLIES.. SEE 4.- FOR INSULATOR DETAILS.. FOR OPEN WIRE COPPER, ALTERNATE DEADEND BELOW MUST BE USED. ALTERNATE SECONDARY DEADEND 4" " ". SALVAGED 4" STRAIN INSULATORS (BELLS) ARE ACCEPTABLE. IDES(KV)PF CONNECTIONS TO SECONDARIES WEDGE GRIP SEE NOTE CU ISEYEBOLT58F CN 6 WEDGE GRIP EYENUT 4" TO SERVICE TO SOURCE LIFT POLE USE MINIMUM 5/6" GUYSTRAND AND 8" SCREW ANCHOR FOR ANGLE POLES AS NEEDED GUYED LIFT POLE DETAIL SHOWN FOR / AND SMALLER TPX & QPX ALSO REQUIRES -LOOP DEADEND AND -EYENUT. SEE FOR SERVICE CLAMP SIZES. 8//4 LOOSIER DANNA 6// McCONNELL DANNA ADCOCK /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D ADCOCK APPR. SECONDARY POLE ATTACHMENTS DEC DEM DEP DEF X 4.-4
9 SECONDARY CABLE DOUBLE DEAD-END FLAT SQUARE WASHER NUT EYENUT 5/8" EYEBOLT BOLTED DEADEND NEUTRAL 4" (IF NECESSARY) GUY ATTACHMENT INSTALL PLASTIC CABLE CAPS TO PREVENT WATER MIGRATION IN CABLE OPEN WIRE DOUBLE DEADEND FOR WIRE SIZES #4 THROUGH / SECONDARY DOUBLE DEAD-END INSULATOR CU ISBSF CN 56 BEND CONDUCTOR ENDS BACK. APPLY INHIBITOR TO COPPER CONDUCTORS. SECONDARY FIBERGLASS ROD 6" /8/ DANNA DANNA ADCOCK /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SECONDARY ATTACHMENTS 4.4- R
10 SECURING SECONDARY CABLE TO NEUTRAL MAKE -4 SHORT WRAPS WITH BINDING WIRE OVER SECONDARY CONDUCTORS, THEN MAKE -4 SHORT WRAPS OVER THE BARE NEUTRAL ONLY. FOLD BACK END OF BINDING WIRE TIGHTLY AGAINST WRAPS OVER NEUTRAL. /8/ BURLISON /6/ BURLISON GUINN REVISED BY CK'D ADCOCK ELKINS APPR. SECONDARY ATTACHMENTS R
11 COMPATIBLE UNIT SERCLMP6ALF SERCLMP4ALF SERCLMPALF SERCLMPNALF SERCLMPN4ALF SERCLMPN6ALF SECONDARY CABLE CLAMP TABLE CATALOG NUMBER DESCRIPTION SERVICE CABLE CLAMP 6 KCM ALUMINUM SERVICE CABLE CLAMP 4/ ALUMINUM SERVICE CABLE CLAMP / ALUMINUM SERVICE CABLE CLAMP # ALUMINUM SERVICE CABLE CLAMP #4 ALUMINUM SERVICE CABLE CLAMP #6 ALUMINUM SECONDARY CABLE TANGENT INSTALL PLASTIC CABLE CAPS TO PREVENT WATER MIGRATION IN CABLE TRANSFORMER PHASES TO BE EXTENDED FOR SECONDARY LEADS SEE NOTE TRANSFORMER POLE 8" ' MINIMUM SERVICE CABLE CLAMP MIDSPAN CABLE MESSENGER (BUTTERFLY) CLAMP CU SDEMSPNCLMPF SEE NOTE 5" MIN. 5" MIN. TANGENT POLE 6" 6". SEE FOR DETAILS ON SECURING CABLE TO NEUTRAL. 6/7/ DANNA ADCOCK /8/ BURLISON ADCOCK /7/ BURLISON BURLISON ELKINS /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SECONDARY ATTACHMENTS 4.4-5
12 HOUSE BRACKETS FASCIA SEE NOTE 7 HOUSE BRACKET CU SDESCRWBOLTF CN HOUSE BRACKETS MUST BE INSTALLED IN STUDS (" X 4") OR EQUIVALENT SUPPORT. SERVICE MAST CUSTOMER'S GUY WIRE OR BRACE SEE NOTE 7 STEEL CONDUIT ONLY FASCIA MAST BRACKET /4" - /" CU SDEMASTCLMPSMF CN 847 " - 4" CU SDEMASTCLMPLGF CN 846. SERVICE MAST SHALL BE OF ADEQUATE STRENGTH OR BE SUPPORTED BY A GUY OR BRACE TO WITHSTAND A MAXMIUM TENSION FORCE OF LBS. IMPOSED BY SERVICE DROP.. " RIGID STEEL CONDUIT IS REQUI FOR MASTS UP TO 4'. LONGER MAST HEIGHTS REQUIRE GUYING, BRACING, LARGER MAST SIZE OR SPECIAL SAG.. DRIP LOOPS SHALL BE FORMED ON SERVICE DROP SERVICE ENTRANCE CONDUCTORS.. THE CONNECTIONS OF THE SERVICE DROP CONDUCTORS TO THE SERVICE ENTRANCE CONDUCTORS SHALL BE MADE BELOW THE LEVEL OF THE SERVICE WEATHERHEAD.. SEE DWGS..- AND.- FOR SERVICE GROUND CLEARANCES AND DWGS..4-9A AND.4-9B FOR SERVICE CLEARANCES AT BUILDINGS. 4. SERVICE ENTRANCE CONNECTORS SHALL BE COVE PER NEC RULE THE SERVICE POINT OF ATTACHMENT SHOULD BE LOCATED BELOW THE LEVEL OF THE WEATHERHEAD OR GOOSENECK. IF THIS IS IMPRACTICAL, THE POINT OF ATTACHMENT MUST BE LOCATED WITHIN 4" OF THE WEATHERHEAD OR GOOSENECK (REF. NEC -54C). 6. CUSTOMER IS RESPONSIBLE FOR PROVIDING AN ATTACHMENT POINT FOR MASONRY AND STEEL BUILDINGS. 7. SEE FOR SERVICE CLAMP COMPATIBLE UNITS. 8/5/4 EANES EANES ADCOCK /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SERVICE ATTACHMENT METHODS DEC DEM DEP DEF X 4.5-
13 MID-SPAN CABLE MESSENGER (BUTTERFLY) CLAMP SERVICE COMPRESSION CONNECTOR WITHOUT COVER ON NEUTRAL TAP SERVICE CABLE CLAMP SEE DETAIL, COVER OVER ALUMINUM COMPRESSION CONNECTORS ON PHASE CONDUCTORS (SEE NOTE ) 5" MIN. ". USE CLEVIS AND SPOOL FOR ANGLE APPLICATIONS AS SHOWN ON.6-. COMPRESSION CONNECTOR EYENUT SERVICE CABLE SERVICE CABLE CLAMP SERVICE COMPRESSION SLEEVES WITH COVERS /8/ BURLISON ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. SERVICE TAPS 4.5- R
14 OPEN WIRE SECONDARY SPACER CU SDEOPENSPACERF CN 846 SERVICE CABLE CLAMP SERVICE CABLE AERIAL SECONDARY CABLE (ASC) COMPRESSION CONNECTORS WITH COVERS MIDSPAN CABLE MESSENGER (BUTTERFLY) CLAMP SERVICE CABLE CLAMP SEE SERVICE CABLE AERIAL SECONDARY CABLE (ASC) BARE NEUTRAL FULL TENSION SPLICE COMPRESSION CONNECTORS WITH COVERS SERVICE CABLE MIDSPAN CABLE MESSENGER (BUTTERFLY) CLAMP SERVICE CABLE CLAMP SEE /7/ DANNA ADCOCK /6/ BURLISON GUINN ELKINS REVISED BY CK'D APPR. MIDSPAN SERVICE TAPS 4.5-
SECTION 4 - SECONDARY CONSTRUCTION OVERHEAD TABLE OF CONTENTS
4. GENERAL SECONDARIES & SERVICES 4.- INDIVIDUAL PHASE SECONDARY OVERHEAD LINE EXTENSIONS 4.- SECONDARY AND SERVICE CABLE SPLICES 4.- INSULATED SERVICE ENTRANCE COMPRESSION CONNECTORS 4.- 4. POLE ATTACHMENTS
More informationOVERHEAD SERVICES - SECONDARY
OVERHEAD SERVICES - SECONDARY Contents - Overhead Services... O-1 General Requirements for Overhead Service... O-2 Names of Parts for Overhead Service... O-3 Service Attachment on an Unguyed Service Mast...
More informationDuke Energy Carolinas Distribution Construction Standards Reference Guide
Duke Energy Carolinas Distribution Construction Standards Reference Guide The Duke Energy Carolinas (DEC) Distribution Construction Standards are available on the My Duke Energy Contractor Portal. Access
More informationOVERHEAD SERVICES - RESIDENTIAL & GENERAL SERVICE. See Chapter 3, Section 3.01 for more information about point of entrance (POE).
6.01 GENERAL OVERHEAD SERVICES - RESIDENTIAL & GENERAL SERVICE See Chapter 3, Section 3.01 for more information about point of entrance (POE). In all cases, the customer installs, owns, and maintains the
More informationSpecifications for Residential Overhead Electric Service Installation
Specifications for Residential Overhead Electric Service Installation This brochure addresses most typical residential overhead service installations. Variances for the following specifications must be
More informationRESIDENTIAL QUICK REFERENCE
RESIDENTIAL QUICK REFERENCE PROVO CITY POWER STANDARDS ELECTRICAL ENGINEERING UPDATED: 2016 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION. 18" MIN. OF TAIL. (NEUTRAL CONDUCTOR MUST BE WHITE OR
More informationTEMPORARY FACILITIES
MUNICIPAL LIGHT & POWER & CHUGACH ELECTRIC ASSOCIATION ELECTRIC SERVICE REQUIREMENTS EXCERPT TEMPORARY FACILITIES 2015 EDITION Effective August 3, 2015 This is an EXCERPT; the complete book is available
More informationBuilding Attachments and Services
Part Four. Other Electrical Procedures CHAPTER 11 Building Attachments and Services All electrical energy supplied to power-consuming devices and appliances within a building must pass through the electrical
More informationOVERHEAD SERVICE. Table of Contents - Section 400
OVERHEAD SERVICE Table of Contents - Section 400 PARAGRAPH 400.0 OVERHEAD SERVICES (0-600 VOLTS)... 1 400.1 GENERAL 1 400.2 IDENTIFICATION OF CONDUCTORS. 1 400.3 MAXIMUM SERVICE ENTRANCE CONDUCTOR SIZE
More informationMSME Testing Centre, 65/1, G. S. T. Road, Guindy, Chennai, Tamil Nadu. Discipline Electrical Testing Issue Date
Last Amended on - Page 1 of 7 I. TRANSMISSION LINE EQUIPMENT & ACCESSORIES ]] 1 Stockbridge Vibration dampers for Power lines Examination & IS 9708:1993 Cl. 7.2 Cl. 7.3 Mass pull off (Slip) Cl. 7.6 120
More informationTOWER & ANTENNA Product Catalog
TOWER & ANTENNA Product Looking for Reliable Solutions to your Communications Network Needs? COMMUNICATIONS Product Fiber Optic, Copper, Demarcation, Bonding, Strand and Cable Solutions for the Communications
More information600 GROUNDING 9/12/2018
00 GOUNDING //0 C N C N,N C N,N N TN0 C TN C TN C TN Installation of Grounding Assemblies Basic Units - Grounding Basic Units - Copperweld Grounding - Pole Ground epair Static Wire History/Policy Static
More information6. SECONDARY SERVICES (under 600 volts) 6.1 AVAILABILITY For the electrical characteristics of available secondary services see Section 3.4.
6. SECONDARY SERVICES (under 600 volts) 6.1 AVAILABILITY For the electrical characteristics of available secondary services see Section 3.4. 6.2 OVERHEAD SERVICES Wiring of any premises for connection
More informationNew Construction Units. a. Includes the furnishing of all labor and equipment for the installation of new construction units.
1 All construction is to follow design and construction documents approved by the Engineer and marked approved for construction. All construction shall also follow the National Electrical Safety Code,
More informationSpecifications for Residential Overhead Electric Service Installation
Specifications for Residential Overhead Electric Service Installation This brochure addresses most typical residential overhead service installations. Variances for the following specifications must be
More informationCutouts and Fuse Links Equipment to protect against faults and over-current conditions on power distribution systems. Open-Type Cutouts Linkbreak Cutouts Loadbreak Cutouts Cutout-Arrester Combinations
More informationREA LISTED. Throughout the catalog you will notice blue highlighted items. These are the most frequently ordered BURNDY Products.
Grounding BURNDY Products E-44 TYPE GRC HIGH STRENGTH GROUND ROD CLAMP For Copper Cable to Rod High copper alloy ground connector for joining a range of cable to copper clad, galvanized steel, and stainless
More informationSplices COOPER POWER SERIES. Connectors Catalog Data CA325007EN. Contents
Connectors Catalog Data CA325007EN Supersedes March 2016 COOPER POWER SERIES Contents Description Page Single-tension sleeves... 2 Dual-tension sleeves... 2 Tension sleeves... 3 Jumper sleeves... 4 Bare
More information6. SECONDARY SERVICES (under 600 volts) 6.1 AVAILABILITY For the electrical characteristics of available secondary services see Section 3.4.
6. SECONDARY SERVICES (under 600 volts) 6.1 AVAILABILITY For the electrical characteristics of available secondary services see Section 3.4. 6.2 OVERHEAD SERVICES Wiring of any premises for connection
More informationORDINANCE NO NOW, THEREFORE, BE IT ENACTED BY THE CITY COUNCIL OF THE CITY OF FAIRBANKS, ALASKA, as follows:
Introduced by: Mayor Eberhart Date: May 23, 2016 ORDINANCE NO. 6013 AN ORDINANCE TO AMEND FGC CHAPTER 10, ARTICLE IX NATIONAL ELECTRICAL CODE, BY ADOPTING THE 2014 NATIONAL ELECTRICAL CODE WITH LOCAL AMENDMENTS
More informationNORTHEASTERN REMC ELECTRIC STANDARDS MANUAL
NORTHEASTERN REMC ELECTRIC STANDARDS MANUAL WARNING Before digging or trenching... Call 811 Indiana Underground Protection Service 1-800-382-5544 AVOID BURIED POWER CABLES 4901 East Park 30 Drive P.O.
More informationSTANDARD TECHNIQUE: OH4K/1
Company Directive STANDARD TECHNIQUE: OH4K/1 Relating to the Design of Insulated Aerial Bundle Conductor For LV Overhead Distribution Systems ST:OH4K/1 13 September 2007-1 of 35 - Document Revision & Review
More informationElectric Service Handbook
Electric Service Handbook Revised August 2017 Contact Information Telephone (253): Electrical Inspection Office 502-8277 7:30 am - 4:30 pm Electrical Inspectors Area Map on Website 7:30 am - 8:30 am Automated
More information(Condensed from National Electric Code)
WIRING, SPECIFICATIONS, INSPECTION, AND METER INSTALLATION PROCEDURES FOR RESIDENTIAL CUSTOMERS SERVED BY SOUTHWEST ARKANSAS ELECTRIC COOPERATIVE CORPORATION Effective April 1, 1974 Revised February 3,
More informationTEMPORARY PROTECTIVE GROUNDING EQUIPMENT
TEMPORARY PROTECTIVE GROUNDING EQUIPMENT TEMPORARY PROTECTIVE GROUNDING EQUIPMENT NOTE: When ordeing assemblies of grounding products, please make sure all items included in the assembly are only from
More informationCONTENTS. B. System Design and Performance Requirements
16060 Grounding and Bonding This document provides design standards only, and is not intended for use, in whole or in part, as a specification. Do not copy this information verbatim in specifications or
More informationGUY-GRIP Dead-end NOMENCLATURE GENERAL INFORMATION SAFETY CONSIDERATIONS
GUY-GRIP Dead-end NOMENCLATURE Please visit our web site at www.preformed.com for additional literature.guy-grip Dead-end Application Procedure - SP2045 Cross-over Marks: (A) Indicate starting point for
More informationELECTRICAL SERVICE UPGRADE RESIDENTIAL AND COMMERCIAL QUICK INFORMATION REFERENCE
ELECTRICAL SERVICE UPGRADE RESIDENTIAL AND COMMERCIAL QUICK INFORMATION REFERENCE PROVO CITY POWER STANDARDS ELECTRICAL ENGINEERING UPDATED: 2015 SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTIFICATION.
More informationGUY-GRIP Dead-end NOMENCLATURE GENERAL INFORMATION SAFETY CONSIDERATIONS
GUY-GRIP Dead-end NOMENCLATURE Tower Products, Dead-end and Dead-end Accessories: Section 1 Please visit our web site at www.preformed.com for additional literature.guy-grip Dead-end Application Procedure
More informationAn altered service that is moved, upgraded (ex., 200 to 400 amp) or changed to meet today's standards for electric service.
ALTERED SERVICE An altered service that is moved, upgraded (ex., 200 to 400 amp) or changed to meet today's standards for electric service. Customer Responsibilities Provide, install and maintain all required
More informationPhone: Fax:
SEPTEMBER 2007 www.nsiindustries.com Phone: 800.321.5847 Fax: 800.841.5566 Mechanical Connectors Dual Rated Single & Double Lugs........................ 1 Panelboard Lugs............................ 1
More informationEffective June, Eaton-Durham Model # UTRS223ACH. Siemens, Model # SUAS877-PG. (or Landis & Gyr # UAS877-PG) Milbank. Model # U1980-O.
Siemens, Model # SUAS877-PG (or Landis & Gyr # UAS877-PG) Eaton-Durham Model # UTRS223ACH Milbank Midwest Model # U980-O UTRS223AMEP These are some examples of the single meter sockets we require for underground
More informationANY SPECIFICATION DRAWINGS OR DATED PRIOR TO SEPTEMBER 2015 WILL NOT BE HONORED.
November 30, 2015 Dear STEMC Member and Contractors, Over the years, STEMC has made many changes to its member requirements for new services and specifications associated with those requirements. As a
More informationUnit Price Labor. INSTALL 138KV DISCONNECT SWITCH WITH MOTOR OPERATOR AND AUXILIARY SWITCHES ON EXISTING STRUCTURE 1 ea.
SUBSTATION B UPGRADE CONSTRUCTION MAJOR MATERIAL NOTES: Contractor to fill in line item column "Est. Qty." for items left blank. Construction Unit No. Description Est. Qty. Unit Labor 100 INSTALL 138KV
More informationMetering Installations for Mobile Homes or Mobile Home Parks:
Metering Installations for Mobile Homes or Mobile Home Parks: Overhead Installations The metering pole must be a minimum of 17 ft, Class 5 pole set at least 4 ft deep so that it will be of sufficient height
More informationSECTION SECONDARY UNIT SUBSTATIONS
SECTION 26 12 16 SECONDARY UNIT SUBSTATIONS PART 1 GENERAL 1.1 SUMMARY This section describes metal-clad, indoor or outdoor, secondary unit substations with integral primary fused disconnect switches,
More informationTEMPORARY METER POLE INSTALLATION
TEMPARY METER POLE INSTALLATION MEMBER PROVIDED Location to be made by REMC within 50' of our transformer or existing service Temporary pole to be properly braced 24" 3 wire weatherhead (located 24" from
More informationSECTION GROUNDING AND BONDING FOR ELECTRONIC SAFETY AND SECURITY
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 28 05 26 GROUNDING AND BONDING FOR ELECTRONIC SAFETY AND SECURITY SPEC WRITER NOTE: Delete // // if not applicable to project. Also delete any other item or paragraph
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 260526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract apply to this Section. 1.2 SUMMARY A. This Section
More informationDIVISION 26 ELECTRICAL Electrical Power Conductors and Cables
PART 1 - GENERAL 1.01 DESIGN REQUIREMENTS A. Scope: Power Conductors and Cables in this section are defined as system voltages above 120V and less than 600V. B. System Voltages Three Phase and Single Phase:
More informationServ. Low-Voltage Cable Insulated Conductors for Overhead and Underground Distribution
Serv Low-Voltage Cable Insulated Conductors for Overhead and Underground Distribution General Cable offers a complete line of insulated cable designs and sizes to meet utility requirements for exceptional
More informationSERVICE ENTRANCES. OPPD S Electrical Service Designer (ESD) shall designate the Point Of Entrance.
SERVICE ENTRANCES 3.01 POINT OF ENTRANCE General Service The customer, or the customer s electrician, should provide OPPD with a site plan, load schedule, and voltage requirements when requesting service.
More informationSECTION GROUNDING
SECTION 16450 GROUNDING PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies general grounding and bonding requirements of electrical and telecommunication installations for personnel safety, equipment
More informationGENERAL NOTES PEDERNALES ELECTRIC COOPERATIVE, INC. RESIDENTIAL AND COMMERCIAL AMP METER LOOP SPECIFICATIONS
GENERAL NOTES 1. Residential and commercial meter loops are typically used when constructing facilities for permanent service. It is important that all guidelines outlined in this document be followed
More informationSECTION CONDUITS AND BACKBOXES FOR COMMUNICATIONS SYSTEMS
SECTION 16711-27 05 28.33 PART 1 - GENERAL 1.01 SUMMARY A. This section includes Labor, materials and equipment necessary to complete the installation required for the items specified under this Section,
More informationPRIMARY LINE EXTENSION
PRIMARY LINE EXTENSION Installation of new electric service to an empty parcel/lot or extending a transformer to within 150' of proposed meter location. This includes installing a permanent branch, addition,
More informationCONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE
ONTARIO PROVINCIAL STANDARD SPECIFICATION OPSS.PROV 604 NOVEMBER 2017 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
More informationSECTION WIRE AND CABLE Raceways and Conduit Motor Power and Control Wiring.
SECTION 16120 WIRE AND CABLE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 16112 - Raceways and Conduit. 2. 16155 - Motor Power and Control Wiring. 1.02 SYSTEM DESCRIPTION A. Performance Requirements:
More informationWIRE AND CABLE Raceways and Conduit Motor Power and Control Wiring.
SECTION 16120 WIRE AND CABLE PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 16112 - Raceways and Conduit. 2. 16155 - Motor Power and Control Wiring. 1.02 SYSTEM DESCRIPTION A. Performance Requirements:
More informationIndex GROUNDING CONNECTORS. TYPE WB Ground Rod Clamps. TYPE G/SRC Ground Rod Clamps. Heavy-Duty Clamps. Standard-Duty Clamps (Universal)
TYPE B Ground Rod Clamps Heavy-Duty Clamps GROUNDING CONNECTORS R30117 For direct burial. For connecting ground wire to driven rod. Designed to maintain proper alignment between ground wire and rod. Cast
More informationWIRING RULES AND REGULATIONS OF TOMBIGBEE ELECTRIC POWER ASSOCIATION
WIRING RULES AND REGULATIONS OF TOMBIGBEE ELECTRIC POWER ASSOCIATION The following rules and information are issued to make it possible for anyone engaged in electrical wiring or installation of electrical
More informationTECHNICAL SPECIFICATION A.B. CABLE
TECHNICAL SPECIFICATION A.B. CABLE 1.0 NATURE OF WORK The work covered by this Specification is for L.T lines in A.B cable as specified herein and in the attached Schedules. The overhead distribution lines
More informationTransmission Line General Requirements Including Typical Overhead Line Structures. Document Number: 1-03-FR-09
Transmission Line General Requirements Including Typical Overhead Line Structures Document Number: 1-03-FR-09 VERSION 1.0 June 2018 This functional requirements document is in line with the organisation's
More informationGrant PUD. Joint Use Standards. For Pole Attachments including: Cable Television Fiber Optics Telecommunications
Grant PUD Joint Use Standards For Pole Attachments including: Cable Television Fiber Optics Telecommunications REVISED: July 25, 2018 INTRODUCTION AND OVERVIEW The information contained in these Joint
More informationThis product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update.
AFC Cable Systems, Inc. Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519.13 METAL CLAD CABLE-MC
More informationDUPLEX INSTALLATION. Customer provides single service lateral attachment point in trough.
DUPLEX INSTALLATION A. GENERAL NOTES: The device shown may be used when the inspection authority having jurisdiction requires the installation of a service disconnecting means adjacent to the meter. MPC
More informationTS 804 CABLES TABLE OF CONTENTS TRAFFIC SIGNAL EQUIPMENT POLE WIRING DIAGRAM LOCATIONS WITH CENTRE MEDIANS
TORONTO TRANSPORTATION January 2012 TS 804 CABLES TABLE OF CONTENTS 1. DRAWINGS TTD 804.001 TTD 804.002 TTD 804.003 TTD 804.005 TTD 804.006 TTD 804.007 TTD 804.010 TTD 804.015 TTD 804.020 TTD 804.025 TTD
More informationELECTRICAL SECTION 2
ELECTRICAL SECTION 2 COMMON WORK RESULTS FOR ELECTRICAL PART 1 - GENERAL 1.1 GENERAL REQUIREMENTS A. This Section includes raceways, conductors and cables, grounding materials, boxes, electrical identification
More informationEngineering Data for Copper and Aluminum Conductor Electrical Cables
2018 Edition Engineering Data for Copper and Aluminum Conductor Electrical Cables THE OKONITE COMPANY Okonite Cables...A higher Standard! The Okonite Company, 2018 Okonite Cables Table of Contents SECTION
More informationKaf-Tech Product Specification
Kaf-Tech Product Specification This product specification is written according to the Construction Specifications Institute MasterFormat, 2014 Update. SECTION 260519.13 METAL CLAD CABLE-LUMINARY CABLE
More informationSECTION OVERHEAD CONDUCTOR RAIL
SECTION 34 23 06 OVERHEAD CONDUCTOR RAIL PART 1 - GENERAL 1.1 DESCRIPTION This Section describes and specifies the performance requirements to design, furnish, install, test, and place into satisfactory
More informationOTHER DISTRIBUTION ONE PIECE WILDLIFE PROTECTOR
OTHER STRIBUTION ONE PIECE WILDLIFE PROTECTOR Designed to provide protection for equipment bushing from accidental contact by squirrels, birds or other wildlife. Hinged construction for easy installation
More informationThis guide can be used to prepare a specification for incorporating wall bracket jib cranes into a competitively bid construction project.
SECTION 14654 WALL BRACKET JIB CRANE ***** Gorbel, Inc. manufacturers a broad range of material handling cranes including monorail, bridge, gantry, and jib cranes. Numerous work station and industrial
More informationCONSTRUCTION SPECIFICATION FOR CABLE INSTALLATION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 604 NOVEMBER 2004 CONSTRUCTION SPECIFICATION FOR CABLE INSTALLATION TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
More informationOperating Instructions
Operating Instructions Series B37000 Hose Reels BB37118 L CB37118 L EB37118 L12D BB37122 L CB37122 L EB37122 L12D BB37128 L CB37128 L EB37128 L12D Dimensional Data C A B D Part # A B C D BB/CB37118 L 31
More informationELECTRICAL SERVICE REQUIREMENTS FOR MOBILE HOME DEVELOPMENTS
Greenbook Prepared by: ABB1 ELECTRICAL SERVICE REQUIREMENTS FOR MOBILE HOME DEVELOPMENTS 052521 Asset Type: Electric Metering Function: Construction Issued by: Quoc Hoang (QxH1) Date: 08-15-17 Rev. #06:
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB #
SECTION 26 0529 - HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More information3. Intermediate metal conduit (IMC). 4. Electric metallic tubing (EMT). 5. Flexible metal conduit (FLEX). 6. Polyvinyl chloride conduit (PVC).
SECTION 16111 CONDUITS PART 1 - GENERAL 1.01 DESCRIPTION A. General: Provide conduits, complete, as shown, specified or required per Contract Documents. Principal items include: 1. Rigid aluminum conduit.
More informationCONSTRUCTION SPECIFICATION FOR POLE ERECTION
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 615 SEPTEMBER 1993 CONSTRUCTION SPECIFICATION FOR POLE ERECTION 615.01 SCOPE 615.02 REFERENCES 615.05 MATERIALS TABLE OF CONTENTS 615.05.01 Concrete.02
More informationChapter ELECTRICAL CODE
Chapter 19.08 ELECTRICAL CODE 19.08.010 National Electrical Code (NEC) adopted. 19.08.100(1) Definitions, general. 19.08.210.5 Identification of branch circuits. 19.08.210.11(C) Branch circuits required;
More informationSECTION GROUNDING AND BONDING
SECTION 16060 PART 1 GENERAL 1.01 DESCRIPTION A. Section includes requirements for an electrical grounding system, including electrodes, grounding rods, connectors, insulators, equipment grounding and
More information1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
More informationFAST-08 F.A.S.T. Foldable, Adjustable, Stackable, Tool-Less System
FAST-08 F.A.S.T. Foldable, Adjustable, Stackable, Tool-Less System Product Focus F.A.S.T. System can be installed independent of the floor system. Stackable to create multiple tiers. No tools required
More informationSECTION PARK NON-SEGREGATED BUS SPECIFICATION
Page 1 of 5 SECTION ------- PARK NON-SEGREGATED BUS SPECIFICATION 1.0 SCOPE 1.1. This specification describes assemblies of 600V, 5Kv and 15Kv non-segregated bus duct, which will be installed indoors and
More informationTitle: YALE OFFICE OF FACILITIES PROCEDURE MANUAL Chapter: 01 - Yale Design Standard Division: Electrical Standards
Date Description of Change Pages / Sections Modified ID 6/15/16 Updated format, division title, and removed references to other sections. - mgl44 A. Summary This section contains design criteria for the
More informationRevisions for the 2015 Edition of the "Specifications and Requirements for Electric Installations (Bluebook)"
Revisions for the 2015 Edition of the "Specifications and for Electric Installations (Bluebook)" PAGE NUMBER OF 2015 EDITION Front Cover Front Cover i i PAGE NUMBER OF 2007 EDITION Front Cover Front Cover
More informationSECTION SUBSTATION BUS ASSEMBLIES ERGLE SUBSTATION
SECTION 16-372 SUBSTATION BUS ASSEMBLIES ERGLE SUBSTATION 1. GENERAL SPECIFICATIONS The work of this Section includes furnishing all labor, equipment, materials (unless specifically identified as Owner-furnished)
More informationCHAPTER 13 GROUNDING AND BONDING
GROUNDING AND BONDING CHAPTER 13 GROUNDING AND BONDING Grounding and bonding must be in accordance with Article 250 of the National Electrical Code (NEC). Bonding is defined in the NEC as the permanent
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 26 0526 - GROUNDING AND BONDING FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions
More informationCompany Replaces previous document Document ID Issue E.ON Elnät Sverige AB Ny engelsk utgåva D
Document type Page Verksamhetsstyrande 1 (5) Company Replaces previous document Document ID Issue E.ON Elnät Sverige AB Ny engelsk utgåva D17-0008968 1.0 Organisation Valid from Valid until Regionnätsaffärer
More informationPATHWAYS FOR COMMUNICATIONS SYSTEMS
270528 PATHWAYS FOR PART 1 GENERAL 1.1 WORK INCLUDED A. Provide all labor, materials, and equipment for the complete installation of work called for in the Contract Documents. 1.2 SCOPE OF WORK A. This
More informationSECTION TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS. A. Solid composite phenolic toilet compartments and urinal screens.
SECTION 102113 TRESPA ATHLON SOLID COMPOSITE PHENOLIC TOILET PARTITIONS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Solid composite phenolic toilet compartments and urinal screens. 1.02 RELATED SECTIONS
More informationCS-21 STREET STRUCTURES TABLE OF CONTENTS
TABLE OF CONTENTS CS-21.0 Street Structures... 1 CS-21.1 Road Signs... 1 CS-21.2 Safety Barriers... 1 CS-21.3 Bollards and Removable Bollards... 1 CS-21.4 Pedestrian Barrier Rails and Handrails... 1 CS-21.5
More informationSection 7: Specifications
Section 7: Specifications 29 31 Building Boundary of Clear Area See Note # 1 8' Shrubs 8' Concrete Pad Equipment 8' TRAVELED WAY M Meter Pedestal 8' Curb Protective Vehicle Posts (Bollards) If Required
More informationCONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 604 NOVEMBER 2008 CONSTRUCTION SPECIFICATION FOR INSTALLATION OF CABLE TABLE OF CONTENTS 604.01 SCOPE 604.02 REFERENCES 604.03 DEFINITIONS - Not Used
More informationLarge cable sizes stronger than pipe/strut
Legrand Seismic Wire Rope/Cable Bracing is the recommended seismic bracing for Legrand wire mesh and ladder tray systems. It is UL Listed, complies with all building codes and standards, and offers significant
More informationChapter ELECTRICAL CODE*
Chapter 19.08 ELECTRICAL CODE* 19.08.010 National Electrical Code (NEC) adopted. 19.08.100(1) Definitions, general. 19.08.210.5 Identification for branch circuits. 19.08.210.11(C) Branch circuits required;
More informationPATENTS ARE PENDING. Building Dimensions. Exterior Dimensions Roof Edge to Roof Edge
Assembly Manual 8x5 PATENTS ARE PENDING Approximate Size 7980303 Storage Area Building Dimensions Exterior Dimensions Roof Edge to Roof Edge Interior Dimensions Wall to Wall Sq. Ft. Cu. Ft. Width Depth
More informationCONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF SIGN LUMINAIRES
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 612 SEPTEMBER 1984 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF SIGN LUMINAIRES 612.01 SCOPE 612.02 REFERENCES 612.03 Not Used 612.04 Not Used
More informationSECTION OUTLET, PULL, AND JUNCTION BOXES
SECTION 16131 OUTLET, PULL, AND JUNCTION BOXES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09900 - Painting. 2. 16112 - Raceways and Conduits. 1.02 SYSTEM DESCRIPTION A. Performance Requirements:
More informationBASIC ELECTRICAL MATERIALS AND METHODS
BASIC ELECTRICAL MATERIALS AND METHODS General Scope Provide raceways for all wiring. All exposed and concealed wiring (including low voltage control, telecommunications, and power limited wiring) shall
More informationSEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets
SEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets Seismic Frame Two-Post Rack Page 11-3 Seismic Protection Products - Racks Page 11-6 Seismic Protection Products - Runway Page 11-8 Seismic
More informationPATENTS ARE PENDING. Building Dimensions. Exterior Dimensions Roof Edge to Roof Edge
Assembly Manual 8x9 PATENTS ARE PENDING Approximate Size 7640303 Storage Area Building Dimensions Exterior Dimensions Roof Edge to Roof Edge Interior Dimensions Wall to Wall Sq. Ft. Cu. Ft. Width Depth
More informationSECTION ROOF SPECIALTIES
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 07 71 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationDaytona Beach Pier Building Renovation Jun 2010
SECTION 15060 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSt. Clair County Electrical Code Regulations
St. Clair County Electrical Code Regulations St. Clair County has adopted the 2011 National Electrical Code as amended with the following listed articles as the St. Clair County version of the National
More informationSTANDARD DRAWINGS. September 2013 UPDATED FEBRUARY 2016
STANDARD DRAWINGS September 2013 UPDATED FEBRUARY 2016 CONSTRUCTION STANDARD DRAWINGS DIVISION 15 LIST OF DRAWINGS: 1. 01 2004-1 Rev. A - Concrete Standards General Outline and Reinforcement Notes 2. 01
More information(3) 1/2 INCH CONDUIT BOTTOM, (2) 3/4 INCH CONDUIT BOTTOM, (8) 1 INCH CONDUIT SIDES Box
3804 South Street 75964-7263, TX Nacogdoches Phone: 936-569-7941 Fax: 936-560-4685 4SD1 4S Box 1"Ko 2-1/8DP Appleton/Oz Gedney Catalog Number 4SD1 Manufacturer Appleton/Oz Gedney Description Steel Square
More informationSECTION HANGERS AND SUPPORTS FOR PLUMBING
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More information