Factors to Consider for Preserving Bearing Assemblies and Expansion Joint Systems
|
|
|
- Beverly Walker
- 6 years ago
- Views:
Transcription
1 Factors to Consider for Preserving Bearing Assemblies and Expansion Joint Systems Mark Kaczinski, P.E. Western Bridge Preservation Partnership 2010 Annual Meeting December 1, 2010
2 Importance of Bearing & Expansion Joint Systems Joints & bearings are an important part of a bridge structural system Typically represent about 1 to 2% of total bridge cost Design and detailing not well understood by many bridge engineers Often criticized for poor performance
3 Importance of Bearing & Expansion Joint Systems Satisfactory long-term performance for expansion joints & bearings can be achieved through the following: 1. Select the correct system 2. Install properly 3. Follow maintenance guidelines
4 1. Select the Correct System
5 Selection of Bearing & Expansion Joint Systems Should be based on lowest life-cycle cost NOT lowest initial cost Often not true for small movement expansion joints Recent push towards use of soft joint systems Pick the most appropriate system given the load and/or movement requirements
6 Selection of Bearing & Expansion Joint Systems Incorporate durable materials in design and follow state-of-the-art specifications when available Current AASHTO pot bearing design requirements No aluminum expansion joints Fatigue designed modular expansion joints with rubber slide springs and bearings
7 2. Install Properly
8 Installation of Bearing & Expansion Joint Systems Starts with proper shipping and handling
9 Installation of Bearing Systems Avoid use of sledge hammer to position elastomeric bearings
10 Installation of Bearing Systems Do not disassemble bearings and keep PTFE protected from UV light and dust/debris
11 Installation of Bearing Systems Properly position expansion bearings based on temperature and/or expected shrinkage and creep
12 Installation of Bearing Systems Follow good construction practices
13 Installation of Expansion Joint Systems Typical problems: Concrete in support boxes of modular joints Poor concrete consolidation Poor detailing Wrong gap opening setting
14 Installation of Expansion Joint Systems Field splices required in staged construction or over-length joint assemblies Strip seal max length of 40 for SSPA shape Modular joint max length of +/- 53
15 Installation of Expansion Joint Proper blockout treatment: Systems Add transverse rebar and/or WWF over modular joint support boxes to reduce possibility of deck cracking Continue longitudinal deck rebar into blockout
16 Installation of Expansion Joint Systems Ensure that seal is properly locked into steel channels at time of installation
17 3. Follow Maintenance Guidelines
18 Maintenance of Bearing & Expansion Joint Systems A good maintenance program for expansion joints and bearings begins with a thorough inspection during the bi-annual bridge inspection Requires good access:
19 Maintenance/Inspection of Bearing Systems Loose/missing/bent anchor rods are common Rolled or walking elastomeric bearings should be reset
20 Maintenance/Inspection of Bearing Systems Severely worn or damaged PTFE/stainless steel sliding surfaces should be replaced
21 Maintenance/Inspection of Bearing Systems Some early (pre 1990 s) pot bearings experience leakage of elastomer. Problem solved with improved AASHTO code design provisions.
22 Maintenance/Inspection of Expansion Joint Systems Number 1 issue is lack of funding to properly clean joint seals or finger joint troughs of debris on annual basis
23 Maintenance/Inspection of Expansion Joint Systems Spalling or delamination of concrete in joint header area is a common problem Maintain cover and carefully consolidate concrete Consider use of non-cementitious materials
24 Maintenance/Inspection of Expansion Joint Systems Problems seen in modular expansion joints prior to fatigue and durability requirement included in AASHTO code: Fatigue damage at welded connections Deterioration of elastomeric elements
25 Maintenance/Inspection of Expansion Joint Systems Typical problems seen on finger joint systems: Failure of anchorage system or header concrete Loosening of bolts on large finger joints Fatigue or impact damage of finger plates
26 Summary Bearing assemblies and expansion joint systems can be expected to provide trouble free performance as long as they have been: Properly Selected Installed Correctly Maintained Thanks for your interest! Questions
Deck Joints and Bearings
Deck Joints Deck Joints and Purpose is to: bridge the gap between spans protect the ends of the girders allow for expansion, contraction and rotational movement prevent water and salt from leakage Most
Wabo Modular STM and D Series Large movement expansion joint system
Wabo Modular STM and D Series Large movement expansion joint system Features Benefits Watertight Durable Versatile DESCRIPTION: The continuous elastomeric gland prevents runoff water from passing through
Introduction To Bridge Joints. Part of The Bridge College Presentations
Introduction To Bridge Joints Part of The Bridge College Presentations It is said, the great legendary coach, Vince Lombardi - at the very beginning of every season gathered up all his players and said..
Wabo Crete StripSeal Parking Series Armored joint and elastomeric concrete expansion joint system
Wabo Crete StripSeal Parking Series Armored joint and elastomeric concrete expansion joint system Features Benefits Flexible applications Versatile movement Heavy duty Watertight DESCRIPTION: Variable
Design strategies for the future
Design strategies for the future Tailor Made Concrete Structures Walraven & Stoelhorst (eds) 2008 Taylor & Francis Group, London, ISBN 978-0-415-47535-8 Expansion joints with low noise emission T. Spuler,
ISBN Verlag Ernst & Sohn - Berlin. Preliminary remarks... VI. 1 Introduction...1
Seite 1 Inhaltsverzeichnis und Vorwort Structural Bearings ISBN 3-433-01238-5 Verlag Ernst & Sohn - Berlin Contents Preface...V Preliminary remarks... VI 1 Introduction...1 1.1 History...1 1.2 Terms and
Dornsife, R.J. "Expansion Joints." Bridge Engineering Handbook. Ed. Wai-Fah Chen and Lian Duan Boca Raton: CRC Press, 2000
Dornsife, R.J. "Expansion Joints." Bridge Engineering Handbook. Ed. Wai-Fah Chen and Lian Duan Boca Raton: CRC Press, 2000 25 Expansion Joints Ralph J. Dornsife Washington State Department of Transportation
Fosroc ETIC Solutions for Bearings and Expansion Joints. constructive solutions
Fosroc ETIC Solutions for Bearings and Expansion Joints www.fosroc.com constructive solutions About Fosroc International Since the company s beginnings over 80 years ago, Fosroc has developed into an International
In Service Replacement of Box Girder Bottom Slab
In Service Replacement of Box Girder Bottom Slab WSDOT Bridge No. 5/537S - Span 11 Craig R. Boone, P.E., S.E. Lynn Peterson Secretary of Transportation 2015 Western Bridge Engineers Seminar Reno, Nevada
Specialty Expansion Joint Systems
www.dsbrown.com Specialty Expansion Joint Systems Bridges Expansion Joint Systems for Architectural, Parking Garage and Bridge Applications Bridge the World with Leading Infrastructure Solutions Corporate
Critical Structures Construction Issues
Critical Structures Construction Issues FLORIDA DEPARTMENT OF TRANSPORTATION STATE CONSTRUCTION OFFICE Specification 1-3: Definitions Contractor s Engineer of Record Specialty Engineer CLASS OF CONTRACTOR
New Construction Expansion Joint Systems
www.dsbrown.com New Construction Bridges REV 12/17 Bridge the World with Leading Infrastructure Solutions Corporate Office 300 East Cherry Street North Baltimore, OH 45872 Telephone: 419.257.3561 Since
Dual Purpose. Sustainable. Sound Attenuation
Wabo SafetyGuard Parking Series Heavy Duty Expansion Control and Traffic Calming System Molded panels manufactured using 100% post-consumer passenger and truck tires Features Benefits Dual Purpose Sustainable
BakeMax Dough Mini Moulder BMMDM02
BakeMax Dough Mini Moulder BMMDM02 2 Instruction Manual 1. Preface ------------------------------------------- P2 2. Machine Introduction -------------------------------- P2 3. Machine Specification and
DeckFast DAYTONSUPERIOR.COM FORMING. Shoring System
DeckFast Shoring System FORMING DeckFast is a highly productive, two component slab form system. It is as simple and quick as erecting two components to provide a ready to pour slab surface. American Owned
Expansion joints for ever longer, lighter bridges
Expansion joints for ever longer, lighter bridges Thomas SPULER Civil Engineer Mageba SA Bülach, Switzerland tspuler@mageba.ch Thomas Spuler, born in 1956, received his civil engineering degree from the
THE EXPANSION JOINTS AND BEARINGS OF THE PORT MANN BRIDGE, VANCOUVER, CANADA
THE EXPANSION JOINTS AND BEARINGS OF THE PORT MANN BRIDGE, VANCOUVER, CANADA Ron Watson, Thomas Spuler, Gianni Moor and Colm O Suilleabhain Ron Watson, born in 1956, received his civil engineering degree
October BC MoTI
11.4 Common requirements... 2 11.4.1 General... 2 11.5 Deck joints... 2 11.5.1 General requirements... 2 11.5.1.1 Functional requirements... 2 11.5.1.2 Design loads... 3 11.5.1.5 Maintenance... 4 11.5.2
HIGH PERFORMANCE REINFORCEMENT PRODUCTS. Product Catalogue.
HIGH PERFORMANCE REINFORCEMENT PRODUCTS Product Catalogue www.hrc-europe.com HRC and its product philosophy The use of T-headed bars in concrete structures has some remarkable benefits compared to the
Bridge Deck Preservation Treatment Options
Western Bridge Preservation Partnership May 17-18, 2016 Salt Lake City, Utah Bridge Deck Preservation Treatment Options Gregg Freeman - Kwikbond Polymers Rob Johnson - Transpo Industries Clay Christiansen
Performance of Concrete Bridge Deck Joints
Brigham Young University BYU ScholarsArchive All Theses and Dissertations 2005-01-04 Performance of Concrete Bridge Deck Joints Lik Hang Yuen Brigham Young University - Provo Follow this and additional
Design of Steel-Concrete Composite Bridges
Design of Steel-Concrete Composite Bridges to Eurocodes Ioannis Vayas and Aristidis Iliopoulos CRC Press Taylor & Francis Croup Boca Raton London New York CRC Press is an imprint of the Taylor & Francis
PRECAST CONCRETE CONNECTIONS - US PRACTICE
PRECAST CONCRETE CONNECTIONS - US PRACTICE Larbi Sennour, PhD, SE President Consulting Engineers Group, Inc. SPEAKERS Precast Connections 3 General Types Wet Connections Semi Dry Dry Wet System - Definition
Application Study on Elastomer Expansion Joint in Heavy Haul Railway
Journal of Civil Engineering and Architecture 9 (2015) 1047-1053 doi: 10.17265/1934-7359/2015.09.004 D DAVID PUBLISHING Application Study on Elastomer Expansion Joint in Heavy Haul Railway Leran Wang,
Cable-Stayed Bridges. PTI Recommendations for Stay Cable Design, Testing and Installation
Cable-Stayed Bridges PTI Recommendations for Stay Cable Design, Testing and Installation David Goodyear, PE SE Vice Chairman, PTI Cable-Stayed Bridge Committee Design of Stay Cables A Simple, efficient
Conergy SolarFamulus II
Conergy SolarFamulus II Installation manual www.conergy.com Table of Contents Table of Contents SolarFamulus II for universal use on flat roofs 1 Introduction 1 1.1 Short description 1 1.2 Intended use
Route 360 Inverted T-beams. Carin Roberts-Wollmann Virginia Tech Tommy Cousins Clemson University Fatmir Menkulasi Louisiana Tech
Route 360 Inverted T-beams Carin Roberts-Wollmann Virginia Tech Tommy Cousins Clemson University Fatmir Menkulasi Louisiana Tech Background Outline Scope and Objectives Development and Testing Topping
TECHNICAL SPECIAL PROVISION FOR CONCRETE REPAIRS. Financial Project ID , &
TECHNICAL SPECIAL PROVISION FOR CONCRETE REPAIRS Financial Project ID 429140-1-52-01, 429140-2-52-01 & 428267-1-52-01 The official record of this Technical Special Provision is the electronic file signed
NOVEMBER 2017 LRFD BRIDGE DESIGN 14-1
NOVEMBER 2017 LRFD BRIDGE DESIGN 14-1 14. JOINTS AND BEARINGS Expansion joints and bearings provide mechanisms to accommodate movements of bridges without generating excessive internal forces. This section
Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations
Issued: Installation Guidelines for Flygt Pumps Pump Anchoring Recommendations Introduction Proper installation and anchorage of Flygt pumps and installation accessories is critical to limiting vibration
SECTION EXPANSION CONTROL
SECTION 07 95 00 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
COMPRESSORS CB /07
COMPRESSORS CB-220 2003/07 Compressor Bases, Skids and Foundations Reciprocating compressors produce unbalanced shaking forces that will produce excessive vibration if an adequate base or foundation are
* technical applications of rubbers and platics
* technical applications of rubbers and platics Applications Techniques des Caoutchoucs et des Plastiques* 1 Rue des Gaillards, ZAC des Doucettes, 95140 Garges-lès-Gonesse, France Tél : +33.1.34.53.03.00
SEM EXPANSION JOINTS.
SE EXPANSION JOINTS www.arsankaucuk.com.tr 1 PROPERTIES ridge expansion joints are designed to permit the longitudinal, vertical movements and small rotation presented on bridge decks due to changes in
Management of Half Joints in RTA Bridges Amie Nicholas, Project Engineer, NSW Roads and Traffic Authority
Management of Half Joints in RTA Bridges Amie Nicholas, Project Engineer, NSW Roads and Traffic Authority SYNOPSIS In recent years, there has been heightened concern over the performance of half joints
Silicoflex J O I N T S E A L I N G S Y S T E M. R.J. Watson, Inc. Bridge & Structural Engineered Systems
Silicoflex J O I N T S E A L I N G S Y S T E M R.J. Watson, Inc. Bridge & Structural Engineered Systems Silicoflex J O I N T S E A L I N G S Y S T E M Technology The Silicoflex Joint Sealing System is
Integrated Pest Management Program Department of Plant Science and Landscape Architecture UConn Extension
Integrated Pest Management Program Department of Plant Science and Landscape Architecture UConn Extension Practical Ways to Increase Production Space One excellent way to reduce production cost per plant
Installing DELTABEAM. Installation of DELTABEAM. Deliveries. Storage on-site
Installing DELTABEAM Installation of DELTABEAM These DELTABEAM installation instructions are intended to complement the project s erection plan. Peikko s technical support can help with the erection plan
Evaluation and Repair of Existing Post- Tensioned Buildings with Paper Wrapped Tendons Experiencing Corrosion Damage
Evaluation and Repair of Existing Post- Tensioned Buildings with Paper Wrapped Tendons Experiencing Corrosion Damage K. Dirk Bondy, S.E. President Seneca Structural Engineering, Inc. The Great American
FRACTURE CRITICAL BRIDGE INSPECTION
FRACTURE CRITICAL BRIDGE INSPECTION In-Depth Report BRIDGE # 9340 (SQUIRT BRIDGE) I-35W over the Mississippi River at Minneapolis, MN JUNE 2006 Prepared For Minnesota Department of Transportation Office
COMPRESSION SEAL EXPANSION JOINT SYSTEM ( IRC:SP:69:2005 & MORTH Interior specification )
COMPRESSION SEAL EXPANSION JOINT SYSTEM ( IRC:SP:69:2005 & MORTH Interior specification ) KANTAFLEX (INDIAN) PRIVATE LIMITED DESIGN OFFICE FACTORY ELASTOMER UNIT #9,VASU STREET, II FLOOR, KILPAUK, CHENNAI-600010
Supporting economical bridge construction the central hinge bearings of the 2 nd Shitalakshya Bridge
IABSE-JSCE Joint Conference on Advances in Bridge Engineering-II, August 8-10, 2010, Dhaka, Bangladesh. ISBN: 978-984-33-1893-0 Amin, Okui, Bhuiyan (eds.) www.iabse-bd.org Supporting economical bridge
D D TYPE A1, A2 & B MICHIGAN DEPARTMENT OF TRANSPORTATION 5-40 CONNECTION. L4" x 4" x 3/8" Brace. C8 x 4.25 Strut. WT9 x 17.5.
Sign length minus Adjust to avoid interference with sign legend A Deck fascia A 6" Equal Equal 6" Sign length (L) varies 6 to 12 PLAN 0 CONNECTION (DECK FASCIA) Angle connection assembly F Face of concrete
Design and Construction of the SH58 Ramp A Flyover Bridge over IH70. Gregg A. Reese, PE, CE, Summit Engineering Group, Inc.
Design and Construction of the SH58 Ramp A Flyover Bridge over IH70 Gregg A. Reese, PE, CE, Summit Engineering Group, Inc., Littleton, CO ABSTRACT: The SH58 Ramp A bridge in Golden, CO is the latest on
DURA-BLOK Rooftop Supports
Cooper B-Line s new line of DURA-BLOK products gives you a versatile and long-term solution for all your roof top support needs. Designed with flexibility in mind, Dura-Blok is ideal for roof top support
MIDAS Training Series
MIDAS midas Civil Title: All-In-One Super and Sub Structure Design NAME Edgar De Los Santos / MIDAS IT United States 2016 Substructure Session 1: 3D substructure analysis and design midas Civil Session
The bridge over the Georges River at Alfords Point has been duplicated with a new incrementally launched bridge.
The Design and Construction of Alfords Point Bridge Mark Bennett, Senior Bridge Engineer (New Design) RTA Harry Cheung, Project Engineer, RTA Trung Doan Project Engineer, RTA Synopsis The bridge over the
BRIDGE PREVENTIVE MAINTENANCE STRATEGY FOR ERIE-NIAGARA LOCAL BRIDGE OWNERS
BRIDGE PREVENTIVE MAINTENANCE STRATEGY Approved January 3, 2007 BLANK Purpose To maximize the non-deficient service life of local bridges in the Erie-Niagara region, members of the Greater Buffalo-Niagara
DESIGN (SUBSTRUCTURES AND SPECIAL STRUCTURES), MATERIALS AND COMPONENTS PART 7 BA 26/94 EXPANSION JOINTS FOR USE IN HIGHWAY BRIDGE DECKS SUMMARY
DESIGN MANUAL FOR ROADS AND BRIDGES VOLUME 2 SECTION 3 HIGHWAY STRUCTURES DESIGN (SUBSTRUCTURES AND SPECIAL STRUCTURES), MATERIALS MATERIALS AND COMPONENTS PART 7 BA 26/94 EXPANSION JOINTS FOR USE IN HIGHWAY
Single Post Anchor Part Number Spectrum Lane ~ Missoula MT ~
Single Post Anchor Part Number 21700 7100 Spectrum Lane ~ Missoula MT 59808 800.791.8056 ~ www.spectrumproducts.com 21700 Man Rev B You have purchased a Spectrum Aquatics Single Post Anchor. Providing
Proposed Modifications to the LRFD Design of U-Beam Bearings
Proposed Modifications to the LRFD Design of U-Beam Bearings Charles D. Newhouse, Scott A. Bole, W. R. Burkett, Phillip T. Nash, Mostafa El-Shami Performed in Cooperation with the Texas Department of Transportation
Slab Bridge Designer 2.1 Help: Example Analysis
August 21, 2006 Slab Bridge Designer 2.1 Help: Example Analysis Using data from the Portland Cement Association Engineering Bulletin 232, AASHTO LRFD Design of Cast-In-Place Concrete Bridges This example
Continuous for Live Load: A Texas Historical Perspective
Continuous for Live Load: A Texas Historical Perspective Scott Walton, M.S.C.E., E.I.T. 1, and Timothy E. Bradberry, M.S.E., P.E. 2 Abstract A significant number of engineers in the United States have
GUIDELINES FOR ROAD DESIGN, CONSTRUCTION, MAINTENANCE AND SUPERVISION
GUIDELINES FOR ROAD DESIGN, CONSTRUCTION, MAINTENANCE AND SUPERVISION Volume I: DESIGNING Section 2: DESIGNING BRIDGES DESIGN GUIDELINES (DG 1.2.7) Part 7: EXPANSION JOINTS ON BRIDGES Guidelines for Road
Modular Expansion Joint System
www.usluk.com A Company Figure 1 - (MEJS) View A Coil Springs Support Bar Box Figure 2 - Skewed Direction of Movement Bridge Axis Elevation Joint Axis ß Centre Beam Anchor Support Bar Box Support Bar Edge
BRIDGE CONSTRUCTION USING SELF-PROPELLED MODULAR TRANSPORTERS (SPMT)
SPECIAL PROVISION August 31, 2009 PROJECT # S-R399(42) PROJECT # S-R399(59) PIN # 6697/7236 SECTION 03253S BRIDGE CONSTRUCTION USING SELF-PROPELLED MODULAR TRANSPORTERS (SPMT) Add Section 03253S: PART
SECTION PERSONNEL DUTY LOCKERS. 1. FPPL Series Police Personnel Duty Lockers, including the following:
SECTION 10501 PERSONNEL DUTY LOCKERS PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 specifications
NDT in Grouted PT Inspection for Bridges
NDT in Grouted PT Inspection for Bridges PTI Technical Conference & Exhibition Miami, FL May 8, 2007 Hong-gang gang Cao CTLGroup (C) COPYRIGHT POST-TENSIONING INSTITUTE, ALL RIGHTS RESERVED Page 1 of 37
SECTION MECHANICAL SPECIFICATION GRIT COLLECTION EQUIPMENT
SECTION 11322 MECHANICAL SPECIFICATION GRIT COLLECTION EQUIPMENT PART 1 GENERAL 1.01 SCOPE There shall be furnished ( ) Grit Separator Mechanism(s) suitable for installation in (a) concrete tank(s) -ft.
De Montfort Mark 7 Incinerator (Flatpack)
De Montfort Mark 7 Incinerator (Flatpack) Introduction This design is specially for those occasions when a large number of incinerators are to be built at one location and transported to the places where
JULY 2014 LRFD BRIDGE DESIGN 5-1
JULY 014 LRFD BRIDGE DESIGN 5-1 5. CONCRETE STRUCTURES Reinforced and prestressed concrete are used extensively in bridge projects. In addition to general design guidance and information on detailing practices,
HIGH SEAL ULF Live Loaded Packing System
Instruction Manual HIGH-SEAL Live-Loaded Packing HIGH SEAL ULF Live Loaded Packing System Contents Introduction... 1 Scope of Manual... 1 Description... 2 Spring Selection... 3 Installation... 3 Parts
SIBLEY POND DESIGN-BUILD BRIDGE REPLACEMENT PROJECT ROUTE 2, CANAAN/PITTSFIELD, MAINE
SIBLEY POND DESIGN-BUILD BRIDGE REPLACEMENT PROJECT ROUTE 2, CANAAN/PITTSFIELD, MAINE G. Keith Donington, PE, Parsons Brinckerhoff, Manchester, NH Hany L. Riad, PhD, PE, Parsons Brinckerhoff, Boston, MA
Bridge articulation No. 1.04
Bridge articulation Scope This Guidance Note gives advice on the selection of the articulation arrangements, the choice of bearing types and dispositions of bearings, for bridges where relative movement
High Performance Thread Rolling Screw for Metal
High Performance Thread Rolling Screw for Metal Features / Benefits ROLOK thread rolling fasteners for metals offer a unique spiral thread form to achieve excellent drive-to-strip performance in many challenging
A. The extent of extruded aluminum walkway covers is shown on the Drawings and as specified herein.
SECTION 10530 - EXTRUDED ALUMINUM WALKWAY COVERS PART I - GENERAL.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General, Supplementary, and Special Conditions and Division
GLOBALGRID TM Translucent Decking
905 Calle Negocio #73123, San Clemente, CA 92673, U. S. A GLOBALGRID TM Tel: 1-866-437-7728, Fax: 1-949-218-9886 www.frpresource.com E-mail: sales@frpresource.com www.globalgriddecking.com GLOBALGRID TM
DURABILITY DESIGN OF BRIDGES FOR SPECIFIED SERVICE LIFE
Western Bridge Engineers Seminar - September 9, 2015 - Reno, NV Mike Bartholomew, PE Principal Bridge Engineer DURABILITY DESIGN OF BRIDGES FOR SPECIFIED SERVICE LIFE Presentation Overview Durability /
A PRODUCT FROM KANTAFLEX (INDIA) PVT LIMITED
ELASTOMERIC BRIDGE BEARING TO LATEST IRC: 83-015 (PART - II) Kanta System of Elastomeric bridge bearing is made out of Poly chloroprene rubber having low crystallization rates and adequate shelf life,
LRFD Bridge Design Manual Changes
LRFD Bridge Design Manual Changes Dave Dahlberg Bridge Design Manual & Policy Engineer May 17, 2017 Bridge Office mndot.gov/bridge Overview 1) Concrete mix designations 2) Reinforcing bar development and
Hydraulic Dock Levelers
Hydraulic Dock Levelers Serco hydraulic dock levelers are installed in thousands of high-volume loading docks worldwide, delivering outstanding performance for strength, safety and durability. Serco Hydraulic
TECHNOLOGY FEATURES. Fast and Simple Installation. Low Stress Design. Maintenance Friendly. Large Movement Range. Temperature Insensitive.
TECHNOLOGY The Silicoflex Joint Sealing system was developed as a direct response to bridge owners asking for a higher quality, longer lasting, more universal joint sealing system. The Silicoflex system
PREFABRICATED STEEL TRUSS SPECIFICATIONS
PREFABRICATED STEEL TRUSS SPECIFICATIONS 1. GENERAL 1.1 Scope All engineering design and related detailing of the bridge(s) shall be provided by the supplier. The design and detailing shall conform to
mageba modular expansion joints the benchmark for large movements
mageba modular expansion joints the benchmark for large movements TENSA MODULAR Types LR and LR-LS Parts and components The joint s individual lamella beams 1 rest on and slide along support bars 2, and
Chapter 4 Bridge Program Drawings
Chapter 4 Bridge Program Drawings Section 4.10-Bridge Railing Introduction Steel bridge railing and concrete bridge barrier rail are installed along the edge of the bridge roadway to keep errant vehicles
Stay-Cable Replacement Design
Stay-Cable Replacement Design Mississippi River Bridge Luling, Louisiana Christopher Ligozio CTLGroup Copyright Post-Tensioning Institute all rights reserved. Page 1 of 35 Luling Bridge Copyright Post-Tensioning
1. Cast-in-place concrete is specified in Section
SECTION 03 38 00 PART 1 - GENERAL 1.01 DESCRIPTION A. This Section describes the requirements for furnishing and installing post-tensioned slabs, jacks, jacking and anchors at Parking Structure, and record
External post-tensioning of pier heads and bearing replacement of Hatirjheel bridge #4
IABSE-JSCE Joint Conference on Advances in Bridge Engineering-III, August 21-22, 2015, Dhaka, Bangladesh. ISBN: 978-984-33-9313-5 Amin, Okui, Bhuiyan, Ueda (eds.) www.iabse-bd.org External post-tensioning
APPLICATION GUIDE PERFORM WITH PRECISION
APPLICATION GUIDE PERFORM WITH PRECISION APPLICATION GUIDE TABLE OF CONTENTS A Word about Safety...1 General Shoring Safety Rules... 2 Single and Independent Post Shore System Safety Rules... 4 General
Selection of Option for Replacement of Major Bridge Expansion Joints
Selection of Option for Replacement of Major Bridge Expansion Joints Greg Forster, Roads and Traffic Authority, NSW SYNOPSIS Large bridges usually have large expansion joints to cater for movements due
Fosroc Solutions for Bearings and Expansion Joints
Fosroc Solutions for Bearings and Expansion Joints www.fosroc.com About Fosroc International Since the company s beginnings over 80 years ago, Fosroc has developed into an International leader in delivering
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS
PART 1 GENERAL 1.01 SUMMARY Section 15140 PIPE HANGERS, This Section includes the furnishing and subsequent installation of: A. Pipe and equipment hangers, supports, and associated anchors B. Equipment
SUMMARY OF PAST EXPERIENCE AND STATE-OF-THE-PRACTICE IN THE DESIGN AND MAINTENANCE OF SMALL MOVEMENT EXPANSION JOINTS IN THE NORTHEAST
0 SUMMARY OF PAST EXPERIENCE AND STATE-OF-THE-PRACTICE IN THE DESIGN AND MAINTENANCE OF SMALL MOVEMENT EXPANSION JOINTS IN THE NORTHEAST Micah H. Milner Mulhern & Kulp 0 S. Maple Street, Suite 0 Ambler,
POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES
POLYGUARD RD-6 A FAIL SAFE PIPELINE COATING SYSTEM FOR REHABILITATION OR GIRTH WELDS ON CATHODICALLY PROTECTED PIPELINES A large percent of corrosion failures on cathodically protected structures are associated
SPECIFICATIONS FOR ERECTION OF PRECAST PRESTRESSED CONCRETE GIRDERS
SPECIFICATIONS FOR ERECTION OF PRECAST PRESTRESSED CONCRETE GIRDERS 1.0 DESCRIPTION The Work shall consist of:.1 Transportation, unloading, and erection of precast prestressed concrete girders;.2 Supply
Originally Issued: 11/24/2010 Revised: 01/20/2017 Valid Through: 11/30/ Design
EVALUATION SUBJECT: HRC 555 SERIES (XTENDER ) AND HRC 670 SERIES T-HEAD (HEADLOCK ) HEADED ENDS OF CONCRETE REINFORCEMENT REPORT HOLDER: Headed Reinforcement Corp. 11200 Condor Avenue Fountain Valley,
SECTION SEISMIC CONTROL OSHPD
SECTION 01451 PART 1 - GENERAL 1.01 DESCRIPTION A. Provide all required seismic restraints and calculations in order to insure that the installation of all architectural, mechanical, and electrical equipment/components
Description. This work shall consist of furnishing materials and placement of modular block wall constructed in accordance with
MODULAR CONCRETE BLOCK RETAINING WALL WITH GROUND REINFORCING The Standard Specifications are revised as follows: 732-R-310r 1of 11 Rev. 12-03-03 SECTION 105, AFTER LINE 48, INSERT AS FOLLOWS: When constructing
INDUSTRIAL PIPE FITTINGS, LLC
Page 1 of 9 SPIROLITE MUNICIPAL AND INDUSTRIAL ODOR CONTROL PIPING Municipal wastewater treatment plants, industrial processes and composting facilities can be assured of trouble free transport of foul
LANE ENTERPRISES, INC. STANDARDS & SPECIFICATIONS
LANE ENTERPRISES, INC. STANDARDS & SPECIFICATIONS The following pages are an index of standards and specifications associated with Lane products. For quick reference purposes, Lane products are shown below
Effect of excessive cement in prestressed concrete girder
Effect of excessive cement in prestressed concrete girder C.V. Kand, T.P. Thite and S.M. Litake DETAILS OF FLYOVER AND METHOD OF CONSTRUCTION This flyover was on an important road with heavy traffic, had
Carter Bridge to Brooks Street Design Build RFI Questions and Answers
1. Project Limits -- Nick Wyatt of Kokosing Construction Co., Inc The project criteria defines the project limits by listing 19 bridges. However, portions of these structures were very recently overlayed
Installation Instructions
EconoDrain Trench Forming System Installation Instructions MultiDrain We Drain Your Site, Not Your Budget MultiDrain Systems, Inc. P.O. Box 88, Barium Springs, NC 28010 (704) 508-1010 or Toll Free 800-433-1119
Installation Procedure
Installation Procedure Information provided herein, including but not limited to, any drawing, design, photograph, graphic, or statement(s) ("Materials") are proprietary and the property of Watson Bowman
INSPECTION OF FIELD WELDING
INSPECTION OF FIELD WELDING Objective Types of Projects Involving Welding Common Welding Terms & Symbols Welder Qualifications Common Welding Requirements Welding Inspection Types of Projects Involving
Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel ASTM A36, Fy = 36 ksi
STRUCTURAL NOTES MATERIAL STRENGTHS Structural Steel Reinforcing Steel Concrete Masonry Structural Lumber Anchor bolts ASTM F1554, Gr. 36 Wide flange beams ASTM A992, Fy = 50 ksi Misc. structural steel
Model: LoLander Series Truck Scale Model: LL FT Model: LL FT Installation, Set-Up and Operation Manual
SCALE WORKS, INC. Model: LoLander Series Truck Scale Model: LL8035-10FT Model: LL8035-11FT Installation, Set-Up and Operation Manual Cambridge Scale Works, Inc. P.O. Box 670 Honey Brook, PA. 19344 (800)
Selection, installation and USage of HatcHeS
Selection, installation and USage of HatcHeS Tech NoTe Hatches for utility structures are manufactured from cast iron, aluminum and steel. The casting requirements, in regard to concrete cover and required
Installation Manual. Orion. TL-3 Steel Barrier. VHD (v2)
Installation Manual Orion TL-3 Steel Barrier VHD (v2) 300914 Table of Contents Orion Introduction.......... 3 Limitations & Warnings. 4 Before Installation..... 3 System Design & Design Considerations
FATIGUE RESPONSE OF AN ULTRA-HIGH PERFORMANCE CONCRETE FIELD-CAST BRIDGE DECK CONNECTION
Graybeal 1 FATIGUE RESPONSE OF AN ULTRA-HIGH PERFORMANCE CONCRETE FIELD-CAST BRIDGE DECK CONNECTION B.A. Graybeal, Ph.D., P.E. Federal Highway Administration 6300 Georgetown Pike McLean, VA 22101 (202)