building movement solutions CONTROL JOINTS FOR FLOORS micratec range VEXCOLT

Transcription

1 building movement solutions CONTROL JOINTS FOR FLOORS micratec range VEXCOLT

2 2 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

3 VEXCOLT contents of micratec range Content Page No. Introduction Introduction 4 Application 5 Micratec Control Joints Micratec SE + SV 6-7 Micratec Ti-Lock NA/VA + NP/VP 8-9 Micratec Ti-Lock NL + ND Micratec Ti-Lock VL + VD Micratec Ti-Lock NS Micratec Ti-Lock VS Micratec TA Micratec TB

4 micratec control joints for floors Introduction Micratec control joints are designed to relieve the stresses within the floor finish layer caused by drying shrinkage, structural variations, thermal gain and loss and slab deflection. Alongside our extensive range of expansion joints, waterproofing systems and fire barriers, Vexcolt has been manufacturing Control Joints for well over 25 years. Throughout that time, quality has been high on our list of manufacturing criteria, and as a result, our control joints are favoured by leading building designers worldwide. Control joints, despite their small size play a very big part in maintaining the good looks of a tiled or paved area. These inconspicuous little joints go largely unnoticed once installed, but if omitted, the effects on expensive flooring finishes becomes embarrassingly obvious. Micratec control joints are designed to relieve the stresses within the floor finish layer caused by drying shrinkage, structural variations, thermal gain and loss and slab deflection. Stresses which, unchecked, will cause cracking or lifting of tiles. And unlike sealant joints, these factory formed profiles are quick and hassle-free to install and will provide lifelong protection of the tile edges. 4 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

5 VEXCOLT micratec control joints for floors Application Control joints can be broadly divided into 3 different types: Type 1 Control joints installed with finishes/wearing surface laid on a thin bed adhesive 2 to 5mm deep. (Micratec NA,NP) Type 2 Control joints that are compression fitted into a slot or saw-cut formed between finishes/wearing surface. (Micratec S) Type 3 Control joints that are installed as finishes/wearing surface are being laid in wet screed or sand/cement bed. (Micratec Ti Lock NL, ND, NS) As a general rule, control joints should be installed within internal floors at approximately 6 metre x 6 metre intervals. In addition, control joints should be considered in other locations; for example at perimeters, columns, kerbs, steps, above existing joints within the substrate, at changes of substrate material and doorways. Control joints should also be considered above supporting walls and beams and at the mid-point of slab spans where the anticipated deflection is expected to be greater than 20mm. Control joints should be installed at more frequent intervals where greater temperature variation is expected; for example in external paving and internal radiant heated screeds. In these circumstances, it is generally accepted that control joints should be installed at maximum 3 metre x 3 metre intervals. Wider control joints with greater movement capacity should be considered in applications where ambient temperatures regularly exceed 30ºC. Please contact our Technical Department who will be pleased to help. Micratec joints are installed in floors to absorb small localised deflections arising from drying, shrinkage, creep and thermal gain and loss. 5

6 CONTROL JOINT 3-7 mm ( 3/32-1/4 ) Joint Width Micratec : SE + SV Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Sightline Blockout Number Floor - Floor EPDM B (mm) ± [Total] H1 (mm) H2 (mm) A (mm) C (mm) ± 1.0 [2.0] 3 SE-003-(H1) - ± 1.5 [3.0] 35 kn 190 kn 30 kn 630 kn 25: 50: 75: SE-005-(H1) ± 2.0 [4.0] 7 SE-007-(H1) Floor - Floor VAMAC - ± 1.0 [2.0] 3 SV-003-(H1) ± 1.5 [3.0] 35 kn 190 kn 30 kn 630 kn 25: 50: 75: SV-005-(H1) ± 2.0 [4.0] 7 SV-007-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : SE denotes a control joint 50mm high. When specifying or ordering please select EPDM or VAMAC core colour as black, grey or stone (beige). 6 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

7 VEXCOLT CONTROL JOINT 3-7 mm ( 3/32-1/4 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 3mm minimum visible line width between finishes Micratec : SE + SV Movement Excellent movement capacity for profile width Traffic Frequency per day > 25,000 10,000 10,000 > 25,000 1,000 System Options Sightline width(s) Height(s) Metal type(s) 3, 5, 7 mm 25, 50, 75, 100 mm 304-grade Stainless Steel 316-grade Stainless Steel CZ 108 Brass Seal colour(s) Black (RAL 7021) Grey (RAL 7038) Beige (RAL 1015) Fire barrier Waterproofing Pre-assembly in factory APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 7

8 CONTROL JOINT 8-9 mm ( 5/16-3/8 ) Joint Width Micratec : Ti-Lock NA/VA Micratec : Ti-Lock NP/VP Micratec : Ti-Lock NA/VA Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Thickness Sightline Blockout Number Floor - Floor NEOPRENE B (mm) ± [Total] H1 (mm) T (mm) A (mm) C (mm) +0.5/-1.5 [2.0] 8: 10: NA-008-(H1) - 35 kn 190 kn 30 kn 630 kn +0.5/-1.5 [2.0] 13: NA-009-(H1) Floor - Wall NEOPRENE /-1.5 [2.0] 8: 10: NP-008-(H1) 35 kn 190 kn 30 kn 630 kn +0.5/-1.5 [2.0] 13: NP-009-(H1) Floor - Floor VAMAC /-1.5 [2.0] 8: 10: VA-008-(H1) 35 kn 190 kn 30 kn 630 kn +0.5/-1.5 [2.0] 13: VA-009-(H1) Micratec : Ti-Lock NP/VP Floor - Wall VAMAC /-1.5 [2.0] 8: 10: VP-008-(H1) 35 kn 190 kn 30 kn 630 kn +0.5/-1.5 [2.0] 13: VP-009-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : Ti-Lock NA denotes a control joint suitable for paving 10mm deep laid onto an adhesive bed. When specifying or ordering please select metal side plates from aluminium, 304-grade stainless steel, 316-grade stainless steel or brass. When specifying or ordering please select NEOPRENE or VAMAC core colour as black, grey or stone (beige). We hold a range of Ti-Lock in stock available for next day delivery. We can also manufacture bespoke heights, widths and colours. Please contact our Sales Department for more information. VEXCOLT 8 United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

9 VEXCOLT CONTROL JOINT 8-9 mm ( 5/16-3/8 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 8mm minimum visible line width between finishes VAMAC versions of these joints are London Underground Limited Fire Safety Performance of Materials tested and approved for below ground applications such as metro stations. Micratec : Ti-Lock NA/VA Micratec : Ti-Lock NP/VP Movement Good movement capacity Traffic Frequency per day > 25,000 1,000 1,000 > 10, System Options Sightline width(s) Height(s) Metal type(s) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 8, 9 mm 8, 10, 13, 15 mm 304-grade Stainless Steel 316-grade Stainless Steel 1005A Aluminium CZ 108 Brass Black (RAL 7021) NEOPRENE/VAMAC Grey (RAL 7038) NEOPRENE/VAMAC Beige (RAL 1015) NEOPRENE/VAMAC APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 9

10 CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Micratec : Ti-Lock NL Micratec : Ti-Lock ND Micratec : Ti-Lock NL Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Thickness Sightline Blockout Number Floor - Floor NEOPRENE B (mm) ± [Total] H1 (mm) T (mm) A (mm) C (mm) NL-008-(H1) +0.5/-1.5 [2.0] NL-009-(H1) - 35 kn 190 kn 30 kn 630 kn 22: 30: 42: NL-010-(H1) 55: 70: NL-014-(H1) +1.0/-3.0 [4.0] NL-015-(H1) NL-016-(H1) ND-008-(H1) +0.5/-1.5 [2.0] ND-009-(H1) Micratec : Ti-Lock ND Floor - Floor NEOPRENE /-3.0 [4.0] 35 kn 190 kn 30 kn 630 kn 22: 30: 42: 55: 70: ND-010-(H1) ND-014-(H1) ND-015-(H1) ND-016-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : Ti-Lock NL denotes a control joint 55mm high. When specifying or ordering please select metal side plates from aluminium, 304-grade stainless steel, 316-grade stainless steel or brass. When specifying or ordering please select NEOPRENE core colour as black, grey or stone (beige). We hold a range of Ti-Lock in stock available for next day delivery. We can also manufacture bespoke heights, widths and colours. Please contact our Sales Department for more information. 10 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

11 VEXCOLT CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 8mm minimum visible line width between finishes Micratec : Ti-Lock NL Micratec : Ti-Lock ND Movement Good movement capacity Traffic Frequency per day > 25,000 10,000 10,000 > 25,000 1,000 System Options Sightline width(s) Height(s) Metal type(s) Metal thickness(es) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 8, 9, 10, 14, 15, 16 mm 22, 30, 42, 55, 70, 90 mm 304-grade Stainless Steel 316-grade Stainless Steel 1005A Aluminium CZ 108 Brass 1.0, 1.5, 2.0, 3.0 mm Black (RAL 7021) NEOPRENE Grey (RAL 7038) NEOPRENE Beige (RAL 1015) NEOPRENE APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 11

12 CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Micratec : Ti-Lock VL Micratec : Ti-Lock VD Micratec : Ti-Lock VL Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Thickness Sightline Blockout Number Floor - Floor VAMAC B (mm) ± [Total] H1 (mm) T (mm) A (mm) C (mm) VL-008-(H1) +0.5/-1.5 [2.0] VL-009-(H1) - 35 kn 190 kn 30 kn 630 kn 22: 30: 42: VL-010-(H1) 55: 70: VL-014-(H1) +1.0/-3.0 [4.0] VL-015-(H1) VL-016-(H1) VD-008-(H1) +0.5/-1.5 [2.0] VD-009-(H1) Micratec : Ti-Lock VD Floor - Floor VAMAC /-3.0 [4.0] 35 kn 190 kn 30 kn 630 kn 22: 30: 42: 55: 70: VD-010-(H1) VD-014-(H1) VD-015-(H1) VD-016-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : Ti-Lock VL denotes a control joint 55mm high. When specifying or ordering please select metal side plates from aluminium, 304-grade stainless steel, 316-grade stainless steel or brass. When specifying or ordering please select VAMAC core colour as black, grey or stone (beige). We hold a range of Ti-Lock in stock available for next day delivery. We can also manufacture bespoke heights, widths and colours. Please contact our Sales Department for more information. 12 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

13 VEXCOLT CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 8mm minimum visible line width between finishes London Underground Limited Fire Safety Performance of Materials tested and approved for below ground applications such as metro stations. Micratec : Ti-Lock VL Micratec : Ti-Lock VD Movement Good movement capacity Traffic Frequency per day > 25,000 10,000 10,000 > 25,000 1,000 System Options Sightline width(s) Height(s) Metal type(s) Metal thickness(es) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 8, 9, 10, 12, 14, 15, 16 mm 22, 30, 42, 55, 70, 90 mm 304-grade Stainless Steel 316-grade Stainless Steel 5251 Aluminium CZ 108 Brass 1.0, 1.5, 2.0, 3.0 mm Black (RAL 7021) VAMAC Grey (RAL 7038) VAMAC Beige (RAL 1015) VAMAC APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 13

14 CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Micratec : Ti-Lock NS Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Thickness Sightline Blockout Number Floor - Floor - B (mm) ± [Total] H1 (mm) T (mm) A (mm) C (mm) +0.5/-1.5 [2.0] +1.0/-3.0 [4.0] 35 kn 190 kn 30 kn 630 kn 22: 30: 42: 55: 70: NS-008-(H1) NS-009-(H1) NS-010-(H1) NS-014-(H1) NS-015-(H1) NS-016-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : Ti-Lock NS denotes control a joint 42mm high. When specifying or ordering please select metal side plates from aluminium, 304-grade stainless steel, 316-grade stainless steel or brass. When specifying or ordering please select NEOPRENE core colour as black, grey or stone (beige). We hold a range of Ti-Lock in stock available for next day delivery. We can also manufacture bespoke heights, widths and colours. Please contact our Sales Department for more information. 14 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

15 VEXCOLT CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 8mm minimum visible line width between finishes Micratec : Ti-Lock NS Movement Good movement capacity Traffic Frequency per day > 25,000 10,000 10,000 > 25,000 1,000 System Options Sightline width(s) Height(s) Metal type(s) Metal thickness(es) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 8, 9, 10, 14, 15, 16 mm 22, 30, 42, 55, 70, 90 mm 304-grade Stainless Steel 316-grade Stainless Steel 5251 Aluminium CZ 108 Brass 1.0, 1.5, 2.0, 3.0 mm Black (RAL 7021) NEOPRENE Grey (RAL 7038) NEOPRENE Beige (RAL 1015) NEOPRENE APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 15

16 CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Micratec : Ti-Lock VS Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Thickness Sightline Blockout Number Floor - Floor VAMAC B (mm) ± [Total] H1 (mm) T (mm) A (mm) C (mm) VS-008-(H1) +0.5/-1.5 [2.0] VS-009-(H1) - 35 kn 190 kn 30 kn 630 kn 22: 30: 42: VS-010-(H1) 55: 70: VS-014-(H1) +1.0/-3.0 [4.0] VS-015-(H1) VS-016-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : T-Lock VS denotes control a joint 42mm high. When specifying or ordering please select metal side plates from aluminium, 304-grade stainless steel, 316-grade stainless steel or brass. When specifying or ordering please select VAMAC core colour as black, grey or stone (beige). We hold a range of Ti-Lock in stock available for next day delivery. We can also manufacture bespoke heights, widths and colours. Please contact our Sales Department for more information. 16 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

17 VEXCOLT CONTROL JOINT 8-18 mm ( 5/16-23/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 8mm minimum visible line width between finishes London Underground Limited Fire Safety Performance of Materials tested and approved for below ground applications such as metro stations. Micratec : Ti-Lock VS Movement Good movement capacity Traffic Frequency per day > 25,000 10,000 10,000 > 25,000 1,000 System Options Sightline width(s) Height(s) Metal type(s) Metal thickness(es) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 8, 9, 10, 14, 15, 16 mm 22, 30, 42, 55, 70, 90 mm 304-grade Stainless Steel 316-grade Stainless Steel 5251 Aluminium CZ 108 Brass 1.0, 1.5, 2.0, 3.0 mm Black (RAL 7021) VAMAC Grey (RAL 7038) VAMAC Beige (RAL 1015) VAMAC APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 17

18 CONTROL JOINT mm ( 13/32-25/32 ) Joint Width Micratec : TA Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Sightline Blockout Number Floor - Floor - B (mm) ± [Total] H1 (mm) H2 (mm) A (mm) C (mm) ± 1.0 [2.0] TA-010-(H1) 120 kn ± 1.5 [3.0] 2 kn 31 kn 30 kn 8: 10: TA-015-(H1) ± 2.5 [5.0] TA-020-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : TA denotes a control joint suitable for paving <10mm deep laid onto an adhesive bed. 18 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

19 VEXCOLT CONTROL JOINT mm ( 13/32-25/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 10mm minimum visible line width between finishes Micratec : TA Movement Excellent movement capacity for profile width Traffic Frequency per day > 25, System Options Sightline width(s) Height(s) Metal type(s) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 10, 15, 20 mm 8, 10, 12 mm 6063 T5 & T6 Aluminium No seal used APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 19

20 CONTROL JOINT mm ( 13/32-25/32 ) Joint Width Micratec : TB Expansion Joint Selection Criteria Load Rating Product Details Joint Gap Movement Eurocode Rating Product Dimensions Product Location Width Capacity (mm) Height Sightline Blockout Number Floor - Floor - B (mm) ± [Total] H1 (mm) H2 (mm) A (mm) C (mm) ± 1.0 [2.0] TB-010-(H1) 10 kn 46 kn 120 kn 25: 35: ± 1.5 [3.0] 30 kn TB-015-(H1) 50: 75 ± 2.5 [5.0] 5 kn 31 kn TB-020-(H1) When specifying or ordering please add the height (H1) required to the Product Reference. For example Micratec : TB denotes a control joint 50mm deep. 20 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

21 VEXCOLT CONTROL JOINT mm ( 13/32-25/32 ) Joint Width Features Surface Easy transit: Americans with Disabilities Act (ADA) compliant across the entire movement cycle 10mm minimum visible line width between finishes Micratec : TB Movement Excellent movement capacity for profile width Traffic Frequency per day > 25, System Options Sightline width(s) Height(s) Metal type(s) Seal colour(s) Fire barrier Waterproofing Pre-assembly in factory 10, 15, 20 mm 25, 35, 50, 75 mm 6063 T5 & T6 Aluminium No seal used APPLICATIONS Airport Terminals Educational Exhibition Centres Department Stores Distribution & Retail Warehouses Factories Hospitals Museums Offi ces & Hotels Parking Places of Worship Residential Buildings Rail, Metros & Elevated Rail Stations Roads & Bridges Shopping Centres Sports Stadiums Supermarkets 21

22 notes for micratec range 22 VEXCOLT United Kingdom T : +44 (0) E : enquiries@vexcolt.com W :

23 VEXCOLT 23

24 VEXCOLT Vexcolt The Sidings Redlake Trading Estate Ivybridge Devon PL21 0EZ United Kingdom T : +44 (0) E : enquiries@vexcolt.com W : Design by The Design Factor, Belfast