M36 My White LED Recessed

Transcription

1 Date: Customer: Project: Type: Qty: M6 My White Order Code: - A2 - TW Series L6 Multi-Mount Form L6R Continuous Flange (Flanged Endcaps) L6R2 Continuous Flange (Flangless Endcaps) A2 Light Engine A2 695lm/9.95W per foot Values calculated from a fixture with CLL using LW Shielding and DMD driver. For additional information please see page 2. TW CCT TW Tunable White K thru 6500K Shielding LW LED Optimized white lens MI Clear Lens w/microprism NB LMO Symmetric A2 LMO Asymmetric 20 Wall Washer A5 LMO Asymmetric 5 Wall Grazer BW LMO Batwing Mounting L6 SF Spackle Flange (/2 Drywall) SF2 Spackle Flange (5/8 Drywall) SF Spackle Flange (After Drywall) SG Slot Grid (9/6 ) (Wire Suspension or /-20 stud) DC Decoustic Ceiling (up to 2 thick) Mounting L6R or L6R2 TB 2 TBS 2 PMT 2 RC T-Bar w/ T-Bar T-Bar Rotating suspension clips w/ /-20 Stud Perimeter Mount Crossbar (Ceilings / to 2 thick ) TS /-20 Stud PM Perimeter Mount 2 L6R only Fixture 02 2 ft. 0 ft. 0 ft ft ft ft ft. XX Runs (over 8 ), round up to the nearest foot and replace the xx with the # (i.e. 09=09 nominal) Individual fixtures and runs are supplied in nominal lengths to ensure full, even, illumination. See pages 2 thru 6 for additional details. intended to fit centered between the grid for SG, TB, TBS, PMT mountings. Finish WH White BK Black SV Silver SP Specify Premium Color Custom colors are available, please consult factory Voltage Volt Volt UNV 20 thru /60hz capable Fixture Options DL Damp Location Rated FS In-line Fuse SS Separate Switching CCEA CCEA approved See page 8 for full details and restrictions Dimming Options DMD eldoled 0-0V (Logarithmic) DMX eldoled DMX (Linear) Emergency Options EC 5 Emergency Circuit Wiring 5 See page 8 for full details and restrictions Product Modifications Please list modification requirements for review by factory: Approvals 5YEAR LED WARRANTY ARRA Compliant Page of 0 M6MYWHITE v.7

2 /6 (6mm) 2 /6 (72mm) 2 /6 (72mm) 5 /6 (mm) 5 /6 (mm) 7 /6 (7mm) 2 7 /6 (62mm) Construction: Housing - Continuous, low copper 606-T6 extruded aluminum profile with aluminum endcaps, available as Individual fixtures (up to 2 ) or Runs. Flange - 9/6 (mm) wide flange runs full lengths of both sides and is part of the main extruded body. Specify continuous flange (L6R) or flush (L6R2) end cap. L6R2 does not work in T-Bar ceiling. Geartray - Low copper 606-T6 extruded aluminum profile. Shielding - Extruded, impact resistant acrylic lens: - LED optimized white lens (LW) - Clear lens with microprism inlay (MI) - LMO symmetric lens (NB) - LMO Asymmetric 5 wall grazer (A5) - LMO Asymmetric 20 wall washer (A2) - LMO Batwing (BW) As a result of the color mixing LEDs, LW lens is recommended for the most uniform illumination, other lenses may allow the separation of colors to be visible Mounting(s) - Spackle in (drywall), Slot grid, Decoustic, T-bar grid, Perimeter, Rotating Crossbar and Threaded Stud Mountings (see pages thru 6 for details). Standard Luminaire lengths - All standard luminaires are supplied in nominal lengths to ensure full, even, illumination. Runs are available in approximately increments starting at the nominal 8 fixture length. ** Individual luminaires are not joinable in the field. Exact length luminaires - Individual luminaires and runs are available in exact lengths to meet your project needs. Please consult factory with your requirements. ** Lens luminance may soften at the very ends of the straight sections for exact length luminaires. M6 Joiner(s) - Runs are supplied with multiple housings that are joined together in the field using the supplied M6 Joiner System. This allows ease of installation and ensures a uniform appearance (see page 8 for detail). Electrical/Performance: Constant Lumen Level (CLL) Curve Selux recommends utilizing the Constant Lumen Level (CLL) curve for the MyWhite product. This is achieved using an algorithm programmed into the controls for driving the two channels of the driver simultaneously so that while adjusting the CCT, the lumen output remains the same. For recommended controls for CLL, please consult Selux. Max Output An alternate way to control the output is by having each channel of the driver controlled individually while changing the CCT. Controlling the channels individually can result in a higher lumen level (see chart on Photometry page). LED Light Engine Brand-name mid-power LEDs create a high efficiency LED light engine able to provide a lumen maintenance of 9% at 25,000 hours and 86% at 60,000 hours per TM-2 report (based on CLL); 86% at 25,000 hours and 7% at 50,000 hours (based on max output). LED Life Calculated L70 greater than 0,000 hours and Reported L70 greater than 60, C per TM-2 (for CLL); Reported L70 of 58, C per TM-2 (for max output). Delivered Lumens - Due to LED manufacturer s tolerances the listed output has a ±5% tolerance. For outputs based on different shielding please see photometry section at the end. CCT - Tunable CCT from 2700K thru 6500K, tolerance within a -step MacAdam ellipse. CRI - Min. 80 Driver - High efficiency, constant current, soft start, Electronic Class 2 with a PFC>0.90. For more detailed information on the available drivers please see page 7. Thermal Performance: Ambient Operating Temperature - Luminaires suitable for Max. ambient temperature of 5 C (95 F) Min. ambient temperature of -20 C (- F) Luminaire Finish: Powder Coat - All Selux luminaries are finished in high quality polyester powder coating in our Tiger Drylac certified facility and are tested in accordance with test specifications for coatings from ASTM and PCI. All products undergo a five stage intensive pretreatment process where product is thoroughly cleaned, phosphated, and sealed. Selux powder coated products provide excellent salt and humidity resistance as well as ultraviolet resistance for color retention. Standard interior colors are White (WH), Black (BK), and Silver (SV). Selux premium colors (SP) are available, please specify from your Selux color selection guide. Warranty: 5 Year Limited LED Luminaire Warranty - Selux offers a 5 Year Limited Warranty to the original purchaser that the M6 MyWhite LED luminaire shall be free from defects in material and workmanship for up to five (5) years from date of shipment. This limited warranty covers the LED driver and LED light engine when installed according to Selux instructions and operated within the Ambient Temperature. For additional details and exclusions, see Selux Terms and Condition of Sale. Certifications and Compliance: NRTL - For Dry and Damp location (I.E. culus) ARRA Compliant RoHS Compliant IC-Rated Page 2 of 0 M6MYWHITE v.7

3 /2 Spackle Flange Mounting (SF) /2 Spackle Flange Mounting (SF) Installation brackets 5/8 Spackle Flange Mounting (SF2) 5/8 Spackle Flange Mounting (SF2) Installation brackets After Sheetrock Flange Mounting (SF) After Sheetrock Flange Mounting (SF) After drywall installation Installation brackets A O.A.L. w/o Flange Spackle Flange Mounting (SF, SF2 & SF) - Dimensions B End Suspensions * C (Ref.) Mid. Suspension D Power Feed Location DMX In/Out Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM 0 ( ft.) ' - 5/6" 0' - 5/8" 0' - 9 /8" 2 0' - /8" 05 0' - /8" (2 ft.) 2' - /" 66 0' - 5/8" ' - 9" 5 0' - /8" 05 0' - /8" 05 0 ( ft.) ' - 5/6" 92 0' - 6 /8" 56 2' - /8" 62 0' - 2 /8" 5 0' - 2 /8" 5 0 ( ft.) ' - /" 225 0' - 6 /8" 56 ' 9 0' - 2 /8" 5 0' - 2 /8" 5 05 (5 ft.) ' - 0 /6" 9 0' - 6 /8" 56 ' - 0 7/6" 80 0' - 2 /8" 5 0' - 2 /8" 5 06 (6 ft.) 5' - 0 5/8" 79 0' - 6 /8" 56 ' - 0 /8" 8 0' - 2 /8" 5 0' - 2 /8" 5 07 (7 ft.) 7' - /" 20 0' - 6 /8" 56 6' 829 0' - 2 /8" 5 0' - 2 /8" 5 08 (8 ft.) 8' - /" 2 0' - 6 /8" 56 7' 2 0' - 2 /8" 5 0' - 2 /8" 5 *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance.. /-20 Threaded rod to structure (supplied and installed by others) Coupler hardware (supplied and installed by others).. /-20 Stud (by Selux).. Ø5/6 [Ø7mm] mounting hole. 5. Drywall/Sheetrock screw (Ref.) 6. Drywall/Sheetrock (Ref.) 7. /6 Plaster skimcoat (Ref.) 8. Drywall/Sheetrock tape (Ref.) 9. Blocking to secure fixture (by others) 0. Electrical connection box, removable side cover for electrical connection pre-installation, once installed the wiring is accessible from below the ceiling through the luminaire.. Brackets installed and shipped in the closed position by Selux. - For runs, rotate bracket to open position so the geartray can be removed to make the housing and wiring connections. - After connections are made, rotate bracket back to the closed position (see installation instructions for full details). - Brackets to be removed only after the luminaire is completely secured to the sheetrock through the spackle flange. Page of 0 M6MYWHITE v.7

4 Slot Grid Mounting (SG) 9/6 Slot Grid Mounting (SG) (Wire Suspension or /-20 Stud) F. 9/6 Slot grid (shown as ref.) 2. Support wire to structure (supplied and installed by others).. /-20 Threaded rod to structure (supplied and installed by others).. /-20 Coupler hardware (supplied and installed by others). 5. /-20 Stud (by Selux). 6. Ø5/6 [Ø7mm] mounting hole. A Housing B End Suspensions Slot Grid Mounting (SG) - Dimensions * C (Ref.) Mid. Suspension D Power Feed Location Grid Spacing F DMX In/Out Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet Feet/Inch MM 02 (2 ft.) ' - 7/6" 595 0' - 5/8" ' - 8 /6" 5 0' - /8" 05 2 Center to Center 0' - /8" 05 0 ( ft.) ' - 7/6" 205 0' - 6 /8" 56 2' - /6" 89 0' - 2 /8" 5 Center to Center 0' - 2 /8" 5 05 (5 ft.) ' - 7/6" 50 0' - 6 /8" 56 ' - /6" 99 0' - 2 /8" 5 5 Center to Center 0' - 2 /8" 5 06 (6 ft.) 5' - 7/6" 85 0' - 6 /8" 56 ' - /6" 50 0' - 2 /8" 5 6 Center to Center 0' - 2 /8" 5 08 (8 ft.) 7' - 7/6" 22 0' - 6 /8" 56 6' - /6" 2 0' - 2 /8" 5 8 Center to Center 0' - 2 /8" 5 *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. Decoustic Mounting (DC) Decoustic Mounting (DC) (Panels up to 2 thick) A Housing Decoustic Mounting (DC) - Dimensions B End Suspensions * C (Ref.) Mid. Suspension D Power Feed Location DMX In/Out Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM 02 (2 ft.) 2' - /" 66 0' - 5/8" ' - 9" 5 0' - /8" 05 0' - /8" 05 0 ( ft.) ' - 5/6" 92 0' - 6 /8" 56 2' - /8" 62 0' - 2 /8" 5 0' - 2 /8" 5 0 ( ft.) ' - /" 225 0' - 6 /8" 56 ' 9 0' - 2 /8" 5 0' - 2 /8" 5 05 (5 ft.) ' - 0 /6" 9 0' - 6 /8" 56 ' - 0 7/6" 80 0' - 2 /8" 5 0' - 2 /8" 5 06 (6 ft.) 5' - 0 5/8" 79 0' - 6 /8" 56 ' - 0 /8" 8 0' - 2 /8" 5 0' - 2 /8" 5 07 (7 ft.) 7' - /" 20 0' - 6 /8" 56 6' 829 0' - 2 /8" 5 0' - 2 /8" 5 08 (8 ft.) 8' - /" 2 0' - 6 /8" 56 7' 2 0' - 2 /8" 5 0' - 2 /8" 5. /-20 Threaded rod to structure (supplied and installed by others). 2. /-20 Coupler hardware (supplied and installed by others).. /-20 Stud (by Selux).. Ø5/6 [Ø7mm] mounting hole. 5. wide alum. angle runs the entire length of fixture to block view into plenum area from below fixture. 6. Suitable for Decoustic ceiling panel installations with panels up to 2 thick (supplied and installed by others). Other ceiling systems possible, please consult factory. Decoustic is a registered trademark of Decoustics Ltd. Corporation. *Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. Page of 0 M6MYWHITE v.7

5 T-Bar Mounting (TB) T-Bar with Stud Mounting (TBS) G G T-Bar with Suspension Clips (TB) (9/6 or 5/6 grid) T-Bar with /-20 Stud (TBS) (9/6 or 5/6 grid). Support wire to structure (supplied and installed by others). 2. Spring steel suspension clips located approximately every ft. (supplied by Selux).. 9/6 T-bar grid (shown as ref.) a. 5/6 T-bar grid (shown as ref.). /-20 Threaded rod to structure (supplied and installed by others). 5. /-20 Coupler hardware (supplied and installed by others). 6. /-20 Stud (by Selux). 7. Ø5/6 [Ø7mm] mounting hole. A O.A.L. with Flange A O.A.L. without Flange T-Bar (TB & TBS) and Perimeter Mount (PMT) - Dimensions B End Suspensions BB (TB mtg.) Suspension Clips ** C (Ref.) Mid. Suspension D Power Feed Location Grid Spacing Feet/Inch MM Feet/Inch MM Feet/Inch MM Quantity Feet/Inch MM Feet/Inch MM Feet Feet/ Inch *02 (2 ft.) ' - /6" 605 ' - 0 5/6" 58 0' - 5/8" x ' - 7 /" 50 0' - /8" 05 2 Center to Center *0 ( ft.) ' - /6" 25 ' - 0 5/6" 9 0' - 6 /8" 56 6x 2' - 0 /" 882 0' - 2 /8" 5 Center to Center *05 (5 ft.) ' - /6" 59 ' - 0 5/6" 97 0' - 6 /8" 56 6x ' - 0 /" 87 0' - 2 /8" 5 5 Center to Center *06 (6 ft.) 5' - 7/8" 825 5' - " 80 0' - 6 /8" 56 6x ' - 0 /" 92 0' - 2 /8" 5 6 Center to Center *08 (8 ft.) 7' - /6" 2 7' - 0 5/6" 22 0' - 6 /8" 56 8x 6' - 0 /6" 20 0' - 2 /8" 5 8 Center to Center *For other lengths consult factory F Wall Angle ' - 0 /6" ' - 0 /" ' - 0 /6" 5' - 0 /" 7' - 0 /" MM G DMX In/Out Feet/ Inch 577 0' - /8" 87 0' - 2 /8" 9 0' - 2 /8" 797 0' - 2 /8" 206 0' - 2 /8" MM **Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance Perimeter Mounting T-Bar (PMT) Perimeter Mount T-Bar (PMT) (Recessed Wall Mounting) 8. Steel Wall Bracket with provision for /-20 fasteners (hardware to code by others) /-20 Stud (by Selux). 0. /2 x Alum. wall angle allows a gap between flange and wall to create shadow line allowing for uneveness of wall. Provision for #0 screws supplied approximately every 2 ft. (hardware to code by others). G Page 5 of 0 M6MYWHITE v.7

6 Rotating Crossbar Mounting (RC) /-20 Threaded Stud Mounting (TS) F Rotating Crossbars (RC) (/ to 2 thick ceiling) /-20 Threaded Stud (TS) ( Threaded Stud). Rotating Crossbar intended for inaccessible ceilings, adjustable for ceiling thickness of / to /-20 Threaded rod to structure (supplied and installed by others).. /-20 Coupler hardware (supplied and installed by others).. /-20 Stud (by Selux). 5. Ø5/6 [Ø7mm] mounting hole. A O.A.L. with Flange Rotating Crossbar (RC), Threaded Stud (TS), and Perimeter Mountings (PM) - Dimensions A O.A.L. without Flange B End Suspensions ** C (Ref.) Mid. Suspension D Power Feed Location Wall Angle F DMX In/Out Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM Feet/Inch MM 02 (2 ft.) 2' - /8" 68 2' - /" 66 0' - 5/8" ' - 9" 5 0' - /8" 05 2' 60 0' - /8" 05 0 ( ft.) ' - /6" 95 ' - 5/6" 92 0' - 6 /8" 56 2' - /8" 62 0' - 2 /8" 5 ' - /8" 97 0' - 2 /8" 5 0 ( ft.) ' - /8" 27 ' - /" 225 0' - 6 /8" 56 ' 9 0' - 2 /8" 5 ' 29 0' - 2 /8" 5 05 (5 ft.) ' - 9/6" 5 ' - 0 /6" 9 0' - 6 /8" 56 ' - 0 7/6" 80 0' - 2 /8" 5 ' - 0 7/6" 85 0' - 2 /8" 5 06 (6 ft.) 5' - /2" 86 5' - 0 5/8" 79 0' - 6 /8" 56 ' - 0 /8" 8 0' - 2 /8" 5 5' - 0 /8" 788 0' - 2 /8" 5 07 (7 ft.) 7' - /8" 262 7' - /" 20 0' - 6 /8" 56 6' 829 0' - 2 /8" 5 7' 2 0' - 2 /8" 5 08 (8 ft.) 8' - /6" 266 8' - /" 2 0' - 6 /8" 56 7' 2 0' - 2 /8" 5 8' /8 5 *RC mounting, consult factory for lengths under 2 **Dimension(s) rounded to the nearest /6 with a ± /6 (mm) tolerance. Perimeter Mount (PM) (Recessed Wall Mounting) Perimeter Mounting (PM) 6. Steel Wall Bracket with provision for /-20 fasteners (hardware to code by others) /-20 Stud (by Selux). 8. /2 x Alum. wall angle allows a gap between flange and wall to create shadow line allowing for uneveness of wall. Provision for #0 screws supplied approximately every 2 ft. (hardware to code by others). Page 6 of 0 M6MYWHITE v.7

7 eldoled Dimming Driver: eldoled DALI dimming (DMD) Luminaires supplied with DUALdrive DALI dimming driver for logarithmic dimming curve. Minimum dimming level preset at factory to %. For dim to dark (down to 0.%), please consult factory. Max. inrush current per driver 0mA²s. eldoled DMX dimming (DMX) Consult factory. *For control recommendation for eldoled drivers, please contact eldoled. Driver Quantity (consult factory for SS option driver quantity) 2 ft. ft. ft. 5 ft. 6 ft. 7 ft. 8 ft. 9 ft. 0 ft. ft. 2 ft. RUN DMD or DMX driver Approximately drivers per ft. Wiring Diagrams DALI Logarithmic (DMD) DMD Page 7 of 0 M6MYWHITE v.7

8 Wiring Diagrams DMX dimming (DMX) GREEN POWER FEED BLACK WHITE TERMINATION RESISTOR DMX FEED When Daisy Chaning fixtures, WHEN DAISY CHANING FIXTURES, REMOVE remove TERMINATION termination RESISTOR AND CONNECT resistor DMX and connect OUT CABLE DMX out cable HOUSING, INDIVIDUAL/START GREEN POWER FEED BLACK WHITE DMX CABLE HOUSING, MID 2 HOUSING, END 2 TERMINATION RESISTOR DMX FEED 2 2 BLACK - DMX NEGATIVE WHITE - DMX POSITIVE BARE - SHIELD BARE WHITE BLACK BLACK WHITE BARE POSITION MALE CONNECTOR 28-2 GA 00V 0A POSITION FEMALE CONNECTOR 28-2 GA 00V 0A BLACK WHITE BARE BARE WHITE BLACK POSITION MALE CONNECTOR 2-GA 00V 0A POSITION FEMALE CONNECTOR 2-GA 00V 0A 2 Page 8 of 0 M6MYWHITE v.7

9 Fuse (FS) - Fusing, luminaires supplied with a in-line fuse located on the hot wire for each feed. (supplied with an 8A slow burn fuse). Damp Location (DL) - Luminaires are suitable for use in damp location(s). Examples of such locations include protected areas under canopies, marquees, roofed porches, and similar locations where the fixture(s) are protected from direct contact with rain, snow, or excessive moisture (such as ocean spray). Interior locations include areas subject to moderate degrees of moisture, such as basements and certain barns and cold storage buildings. All solder points on LED boards are conformal coated. The phosphor layer of the LEDs is free of coating to avoid hazing. Separate Switching (SS) - Luminaires available with separately switched (nominal) sections starting at 7 and up. Luminaire is intended to be wired to the same panel/breaker (not intended for Emergency use). - To specify this option, the number of separately switched sections and locations of these sections must be provided at time of order. *If the project requires different separate switching than outlined above please consult the factory. Emergency Circuit (EC) - Luminaires with EC option compliant to UL 92 listed emergency luminaire. EC luminaires are intended to be wired to separate panels/breakers for emergency use. - For to 6 nominal luminaires, the entire fixture is wired for operation on emergency circuit. - For 7 and up nominal luminaires, the first nominal length is wired for operation by a separate EM circuit by default to meet the required Life Safety Code (NFPA 0). **If a different configuration is needed please consult the factory. Flex Whip - standard for FF mounting 90 Elbow on top of the housing (7/8" feed hole) /8" flexible metal conduit (6' long) 6" leads Straight fitting Joiner System - standard for Runs Fixture extrusion Recommended #2 Phillips drive Joiner extrusion Fixture extrusion Additional view Page 9 of 0 M6MYWHITE v.7

10 Photometry LW Optics / 8W LED / CLO Link to photometry (IES & PDF files) Catalog #: L6-A2-TW-LW-X-0-WH-20 Report #: 75-0CLL Delievered Lumens: 2776 Input Watts: 8.86W Efficacy: 70 Power Factor: Total Harmonic Distortion: 5.% CCT: K CRI: 8.2 Max Candela: from Vertical Spacing Criterion (0-80):.26 Spacing Criterion (90-270):.22 Spacing Criterion (Diagonal):. Maximum Candela = 06.7 Located At Horizontal Angle = 0, Vertical Angle = # - Vertical Plane Through Horizontal Angles (90-270) # 2 - Vertical Plane Through Horizontal Angles (0-80) 2 LUMEN OUTPUT BASED ON CONTROL SETTINGS MAX OUTPUT LEVEL Driver may limit output above this line This photometry can be used for all CCTs when utilizing the constant lumen level (CLL) curve for My White. For other outputs, please consult the factory. CONSTANT LUMEN LEVEL 2700K 6500K CCT RECOMMENDED AREA OF OPERATION (CONSTANT LUMEN LEVEL [CLL] SETTINGS) ADDITIONAL Results may LUMEN fluctuate ADJUSTABILITY when USING fixture MAX is OUTPUT used outside CURVE of the Constant Lumen Level curve. My White and the Circadian Rhythm Humans have an internal clock that affects everything from sleep patterns to productivity to health. This clock is called the circadian rhythm. As humans evolved in the days before electric lighting, they had natural exposure to various levels (both color temperature and intensity) from the sun. By adjusting electric lighting to mimic the natural hue and intensity of the sun, it can help restore the body to a natural state. Various studies have shown that this can help with alertness, behavioral issues, and productivity. The Selux proprietary My White technology allows you to adjust both the amount and color of your light, creating a comfortable environment for offices, educational facilities, hospitality, or any other installation where varying light could benefit the occupants. Set up the My White luminaires to a whole building solution, and you could create an automatic adjustment to the light to mimic daylight. Page 0 of 0 M6MYWHITE v.7