APPROVED MATERIALS AM-6 WASTEWATER TABLE OF CONTENTS. Table 6: Wastewater...2
|
|
|
- Mariah Garrett
- 6 years ago
- Views:
Transcription
1 APPROVED MATERIALS AM-6 WASTEWATER TABLE OF CONTENTS Table 6: Wastewater...2
2 Table 6: Wastewater Materials that are not on the following table MUST be approved by Council refer to AM-1 General Provisions. AM-6.1 Wastewater Pipe Trunk Mains: larger than 150mm. These to be specifically approved and specified by Council. Reticulation Mains: 150mm. Lateral/connection: 100mm and 150mm. Rising mains minimum 76mm ID. AM Spiral-welded Steel Pipe Internal linings include concrete or epoxy AM Ductile Iron Class K9 /K12 Structural mains NZS 4442 or AS1579 Structural mains AS/NZS 2280 and Specific design and approval. Polyken YG111 external wrapping or Speed Steel with polyethylene coatings. Note internal coating must be resistant to hydrogen sulphide. capable of meeting the required standard. Specific design and approval. Light cement lined with Tyton joints. External protection with greensleeve. Generally suspended pipes and high structural loadings. Note internal coating must be resistant to hydrogen sulphide. capable of meeting the required standard. Tubemakers of Australia Licence #2029 Steelpipe Zealand Tubemakers Australia Page 2 Updated 01/07/2014 New of
3 AM Ductile Iron Pipe Light Structural mains Cement-lined Tyton Excel PN20 and PN35 AM upvc Pipes (solid wall) and fittings for gravity applications. (SN 16 - TCC Only) AM upvc Pipes (solid wall) and fittings for pressure applications (SN 16) AM AM AM Polyethylene Pipe (PE) for pressure applications PE100 SDR17 or PE80, SDR 17 (minimum PN12) Tracer Wire / Warning Tape Tracer Wire Reticulation mains and lateral/ connections Trenchless Installation Rising Mains AS/NZS 2280 and Specific design and approval. Tyco Flow Control Pacific Page 3 Updated 01/07/2014 With Tyton joint elastomeric seals and socket / spigot joints (with blue polyethylene sleeving). Note: internal coating must be resistant to hydrogen sulphide. capable of meeting the required standard. Tyco Flow Control Pacific Licence #SMK0883 AS/NZS 1254 Rubber ring jointed Iplex Pipelines New Iplex Licence #1697 Zealand Marley Licence #2365 Marley New Zealand Limited RX Plastics AS/NZS 1477 Specific design and approval. Iplex Pipelines New Keyplas Zealand Marley New Zealand Limited RX Plastics AS/NZS 4130, 4131 Specific design and approval. Iplex Pipelines New Zealand Pipes shall be jointed in accordance with Marley New manufacturer s recommendations, and be standard Zealand Limited black colour with inner core colour brown. RX Plastics Electrofusion coupling will be accepted where pipe Waters & Farr line strings are to be connected, connection of fittings and repairs to pipelines. A continuous 4.0mm 2 multi-strand (minimum of 4) polythene sleeved cable.
4 AM Warning / Detection Tape Open Cut Installation AM-6.2 Seal Rings Comply with AS AM-6.3 Fittings AM Cast-iron Socket and Spigot Fittings Cast-iron Flanges AM Ductile Iron Pipe Flanged, Socket and Spigot Fittings Flanges AM Stand-alone Flanges AM Bolts, Nuts and Washers to be hot-dipped galvanised AS/NZS 1830 and AS/NZS 2544 Table D and coated to AS/NZS 4158 and. AS/NZS 2280 to Table D or Raised Face and drilled to AS 4087, and coated to AS/NZS 4158 and Table D coated to AS/NZS 4158 and AS/NZS 1111 and 1112 Width - 100mm (min.) Thickness 80mu Printing TBC Printing Height 80mm Tape Colour - TBC Elastomeric seals for wastewater purposes. Rated at PN16 or higher. Epoxy coated. PVC, ductile or cast iron. Steel and Tube - Unflanged adaptor - Ductile Iron ISO metric hexagon commercial bolts and screws and ISO metric hexagon nuts, including thin nuts, slotted nuts and castle nuts. Polymark Packaging Page 4 Updated 01/07/2014 Iplex Pipelines New Zealand (Licence #SMK1174) Gillies Metaltech HJ Asmus & Company Limited Crevet Pipelines Surecast Metals Tyco Flow Control Pacific Gillies Metaltech Hygrade Products Iplex Pipelines New Zealand Marley New Zealand Limited Steel and Tube Holdings Limited s who can supply to the relevant standards.
5 AM Stainless Steel Bolts, Nuts, Washers and fastenings provided they are 316-grade stainless steel with factory applied molybond coating AM Gibaults - Cast iron (coating as per standard) - Gunmetal DR LG2 with ABS belly - M stainless steel, (with clips fusion coating as per standard) AM PE Fittings Complying with AS 1252 High Strength Steel Fastenings 4158 and Coating to ASTM A276 AS/NZS 4158 Stainless Steel only to be used for buried installation. s who can supply to the relevant standards. Use 316-grade stainless steel bolts. Preference for long barrel. Use 316-grade stainless steel fasteners. Agru Butt welding and Electro fusion Fittings Viking Johnson Aqua fast, Aqua grip and Ultra grip Mechanical Fittings for Polyethylene Pipe. Hawle System 2000 Mechanical Fittings for Polyethylene Pipe Philmac Licence #1271 Pushlok Licence #1494 Plasson Licence #1494 and 1271 Alprene A16 Easygrip Licence #1157 GF Compression fittings Licence #1157 "Plassim" MDPE Fitting to AS/NZS 4129 Licence # WMKA21062 "Magnum" MDPE Fitting to AS/NZS 4129 Licence # SMK02432 Humes Hynds Pipeline Pipe Gillies Metaltech Viking Johnson Maxifit (with Sheraplex coated bolts) Crevet Pipelines Milnes Pty Tyco Flow Control Pacific Iplex Pipelines New Zealand Marley New Zealand Limited Asmuss Plastic Limited PPI Corporation (NZ) Limited Waters and Farr RX Plastics Hygrade Products RX Plastics AM upvc Fittings AS/NZS 1260 RRJ fitting only to be used. Iplex Pipelines New Keyplas Zealand Humes Page 5 Updated 01/07/2014 Pipeline
6 AM Rubber Sleeves Reticulation pipes (non-pressure) AM-6.4 Valves AM Valves 50mm Resilient seated anti-clockwise closing Rated at PN16 AM-6.5 External and Internal Protective Coating Flanges to be raised face and drilled as per standard Manholes Pump station and rising mains AS/NZS 4326 AS/NZS NZS/BS 5163 Class 1 AS/NZS 4158 and AS 4087 Iplex Licence #SMK1174 Marley Licence # WMKA20224 All couplings used shall have a central 316-grade stainless steel sheer band. Teflon gland packing or 2 or more O ring seals and dust cover. In-line valves shall be the same diameter as the reticulation main. AVK Australia Pty Licence #SAI2420 and 2573 Tyco Flow Control Pacific Licence #PRD/R61/0412/2 Crevet Pipelines Licence #1327 Hawle 4060E2 and 4500E2AS series Licence #SMK20123 Marley New Zealand Limited Furnco Pty AVK Australia Pty Gillies Metaltech Tyco Flow Control Pacific Crevet Pipelines Hawle Humes Hynds AM mm to 2500mm id with Precast Base "Done" Manhole Sherriff Drainage AM Concrete Lid (flat top) with 600mm openings Page 6 Updated 01/07/2014 Pipeline Pipe
7 AM Manhole Sealant, Flexible Jointing Compound AM Access Steps grade stainless steel access steps AM Plastic Encapsulated Stainless Steel Access Step AM Cast-iron Covers and Frames: 600mm nominal diameter minimum AM Ductile iron Covers and Frames: 600mm nominal diameter minimum AM Manhole Connectors AM AS/NZS 1657, AS4198 BS EN 124 vehicle loading or AS kN load rating AS kN (Class D) load rating Page 7 Updated 01/07/2014 BM100 or SM9020. Stainless manholes steps - 16mmÆ. Costavic Nextep Miyama NZ Licence #jp-jqa-qm6570 Includes "non-rock". Hygrade Products Pipe & Infrastructure Includes "non-rock". Gatic Pty Webforge NZ - Code DCC6DIPAC Saint Gobain PAM Gatic - Code GM300S6D4 Webforge NZ Hygrade Products St Gobain Korum Pipe & Infrastructure Hygrade 600mm Maestro PVC Proprietary units only. Iplex Pipelines New Zealand Humes Pipeline
8 AM PE PE 80. PE 100. Page 8 Updated 01/07/2014 Solo Plastics s who can supply to the relevant standards. AM Epoxy Sealing joints and step 2-part epoxy (e.g., Humebond, Hybond). irons AM Concrete Lid surround NZS MPa. AM Reinforcing Steel Lid surround AS/NZS 4671 D10 Grade 300. Pacific Steel Group AM Entry Safety Grill Entry Safety 75mm square Caliber Safety Grill Grill MH TCC Hygrade Products TCC Only mesh Galvanised 500mm Hot dipped Caliber Safety Grill Grill MH TCC Maestro Galvanised if made Galvanised 600mm of steel or of 316 grade stainless steel Caliber Safety Grill Grill MH TCC Maestro Stainless Steel 600mm Allows installation without heavily modifying existing manhole Capable of locking and securing to manhole Test load 400kg Can be removed easily by one person 5min Connected by chain or similar to ensure grill does not fall into All other products are subject to specific approval or trial installations. Humes mm Nominal Safety Grille. Humes mm Nominal Safety Grille.
9 AM-6.6 Rodding Eyes AM Reinforced Concrete Pipe AM Cast-iron Cover and Frames 545mm nominal diameter minimum. AM Ductile iron Cover and Frames 545mm nominal diameter minimum. To create chamber MH (must be able to support the weight of the grill) s name, applicable information on product Does not introduce any additional Health and Safety issues NZS soon to be replaced with AS/NZS 4058 BS EN 124 vehicle loading or AS kN load rating. AS kN (Class D) load rating. Page 9 Updated 01/07/ mm Ø cut to 600mm length. Hygrade Products Pipe & Infrastructure Hygrade 500 HD Hytec Cover & Frame Humes HD Non Rock Cover & Frame Hygrade Products Pipe & Infrastructure
10 AM UPVC Fttings and Bends AS/NZS deg swept bend. Solvent welded threaded mall fitting. Threaded cap. Page 10 Updated 01/07/2014 Iplex Pipelines New Keyplas Zealand (Licence #SMK1174) Marley New Zealand Limited (Licence # WMKA20224) AM Concrete Lid surround NZS MPa s who can supply to the relevant standards. AM Reinforcing Steel Lid surround AS/NZS 4671 D10 Grade 300. Pacific Steel Group AM-6.7 Pump Stations Fibreglass Packaged Pump stations by specific design & approval only AM Wet Well FRP Pump Stations are subject to specific design and approval. AM Centrifugally Spun AM Flushed Jointed Concrete Pipes Class 2 (X) Pump stations Minimum 1800mm Ø. Altex- Carboline product range : Carboguard 504 as the primer to new or used concrete surfaces followed by 2x coats of Carboguard 690 Guide Rails Pump stations Schedule 10, 316-grade stainless steel pipe. Any joints to be an internal pressed fit stainless steel sleeve. Guide Rail Brackets Pump stations Flygt 316-grade stainless steel. AM AM Cable Brackets Pump stations 316-grade stainless steel. 4 AM Pump Valve Chamber AM Chamber Walls Pump stations 200mm concrete block. 1 AM Chamber Floor Pump stations Cast in-situ concrete 17.5 Mpa. 2 AM Chamber Top Slab Pump stations Concrete may be precast 17.5 MPa.
11 3 AM AM AM AM AM AM Flanges Pump stations Gaskets shall be 3mm full face neoprene. Access Lids Pump stations 6mm aluminium chequer plate. Stainless steel 316-grade frame and fittings. Specific design that considers odour and water infiltration. Valves 50mm Resilient seated anti-clockwise closing Rated at PN16 External and internal protective coating Flanges to be raised face and drilled as per standard Ductile Iron Non-return Valves Pump stations AS/NZS NZS/BS 5163 Class 1 AS/NZS 4158 and AS 4087 Teflon gland packing or 2 or more O ring seals and dust cover. In-line valves shall be the same diameter as the reticulation main. Resilient seated anti-clockwise closing. Rated at PN16. External and internal protective coating. Flanges to be raised face and drilled as per standard. Valves to have hand wheels. AVK Australia Licence #SAI2420 and Tyco Flow Control Pacific Licence #PRD/R61/0412/2. Crevet Pipelines Licence #1327. Hawle 4060E2 and 4500E2AS series Licence #SMK Pump stations AS 4794 Ball type. Other types require specific approval. Ductile Iron Fittings Pump stations AS 2280 AS/NZS 4158 Entry Safety Grill All ductile valves, fittings and pipes shall be coated in accordance with AS/NZS Specific design and approval AVK Australia Pty Gillies Metaltech Tyco Flow Control Pacific Crevet Pipelines Hawle Humes Hynds Pipeline Pipe Page 11 Updated 01/07/2014
12 AM Pumps Pump stations Flygt submersible wastewater pumps. ITT Flygt AM Pump Discharge Pipes Pump stations AS 2280 Ductile iron pipes and fittings AS 2280:1999 Schedule 10, 316-grade stainless steel. AM Rising Main Pump stations AS/NZS 4130 Welded or flanged joints. RX Plastics PE100 or PE80 polyethylene pipe (minimum PN12). AM Bolts, Nuts and Washers Pump stations All to be 316-grade stainless steel and coated before installation to prevent "binding". AM Tracer Wire Rising main A continuous 4.0mm 2 multi-strand (minimum of 4) polythene sleeved cable. Page 12 Updated 01/07/2014
Application Standard Product / Comment
1 Table 2: Wastewater s that are not on the following table MUST be approved by Council refer to Chief Engineer AM-2.1 Wastewater Pipe Trunk mains: larger than 150mm. These to be specifically approved
APPROVED MATERIALS AM-5 STORMWATER TABLE OF CONTENTS. Table 5: Stormwater...2
APPROVED MATERIALS AM-5 STORMWATER TABLE OF CONTENTS Table 5: Stormwater...2 Table 5: Stormwater Materials that are not on the following table MUST be approved by Council - refer to AM-1 - General Provisions.
APPROVED MATERIALS AM-7 WATER SUPPLY TABLE OF CONTENTS. Table 7: Water Supply...2
APPROVED MATERIALS AM-7 WATER SUPPLY TABLE OF CONTENTS Table 7: Water Supply...2 Table 7: Water Supply Materials that are not on the following table MUST be approved by Council refer to AM-1 General Provisions.
Completed applications and supporting information should be addressed to:
Authorised by : City Waters Unit Manager Section A Page 1 of 5 SECTION A : ACCEPTABLE FITTINGS AND MATERIALS 1.0 SCOPE This specification covers the list of materials acceptable for use in Hamilton City
Appendix A: Acceptable pipe and fitting materials
Appendix A: Acceptable pipe and fitting materials Where the table in NZS4404:2010 and the Supplement document table conflict, precedence shall be given to the supplement document.. Pipe Materials VC (Vitrified
Technical Manual PE PIPE SYSTEM MAINTENANCE GUIDE ISSUE 1.1
Technical Manual PE PIPE SYSTEM MAINTENANCE GUIDE ISSUE 1.1 Ref: TM001 28 June 2008 Disclaimer In formulating this manual PIPA has relied upon the advice of its members and, where appropriate, independent
TECHNICAL SPECIFICATION
TECHNICAL SPECIFICATION TECHNICAL SPECIFICATION Request for Offer (RFO) SUPPLY AND DELIVERY OF DUCTILE IRON CEMENT LINED PRESSURE PIPES AND FITTINGS FOR HURSLEY ROAD AND TOOWOOMBA CECIL PLAINS ROAD (GREENWATTLE
SECTION 13. A. Extent of Work: The requirements of this section apply to the piping systems specified elsewhere in these specifications.
SECTION 13 PIPE, TUBE AND PART 1 - GENERAL 1.01 DESCRIPTION A. Extent of Work: The requirements of this section apply to the piping systems specified elsewhere in these specifications. 1.02 QUALITY ASSURANCE
PRODUCT SPECIFICATIONS FOR PRODUCTS AND MATERIALS. Numerical Listing
S FOR PRODUCTS AND MATERIALS Numerical Listing WSA PS 200 WSA PS 201 WSA PS 202 WSA PS 202S Ductile Iron Pipes (CIOD) for Pressure Applications - Water Supply and Sewerage Ductile Iron Fittings (CIOD)
DUCTILE IRON PIPES AND FITTINGS DETAILED PRODUCTS SPECIFICATIONS
DUCTILE IRON PIPES AND FITTINGS DETAILED PRODUCTS SPECIFICATIONS General All Materials shall be EN, ISO or equivalent standard and shall be supplied from approved manufacturers. According to the International
AVK Couplings and Adaptors
AVK SAUDI VALVES AVK Couplings and Adaptors Solutions for All Applications 2 A Comprehensive Range of Couplings and Adaptors Product quality The complete coupling range is manufactured by AVK in accordance
WANG TAPPING SADDLES. fast, permanent tapping SOLUTION FOR BOTH rigid and flexible pipe types FEATURES DESCRIPTION APPLICATION TECHNICAL DATA
WANG TAPPING SADDLES 0-0 fast, permanent tapping SOLUTION FOR BOTH rigid and flexible pipe types FEATURES bodies are manufactured from either stainless steel or Ductile Iron Fusion Bonded Epoxy coated
PRODUCT OVERVIEW AUG 2014
AUG 2014 PRODUCT OVERVIEW AUSTRALIAN OWNED AND OPERATED Clover Pipelines is Australia s fastest growing specialist supplier and distributor of innovative pipeline products with years of industry experience
List of Acceptable Product Specifications CPDMS0018
List of Acceptable Product Specifications CPDMS0018 17 July 2018 Contents Foreword 3 Pipe and Fittings 4 Polyvinylchloride (PVC) 4 Ductile Iron (DI) 4 Mild Steel (MS) 5 Polyethylene (PE) 5 Polypropylene
Facility Sanitary Sewers
University of New Hampshire University of New Hampshire Scholars' Repository Division 22 Plumbing Chapter 5 Technical Construction and Renovation Standards 4-23-2015 221313 - Facility Sanitary Sewers Sandra
Laboratory Accreditation Programmes
Laboratory Address PO Box 6178, Upper Riccarton, Christchurch, 8442 52 Hayton Road, Sockburn, Christchurch, 8042 Telephone 03 343-3530 URL Authorised Representative Client No. 153 Programme Accreditation
The Manitoba Water Services Board SECTION Standard Construction Specifications September 2013 Page 1 of 7
September 2013 Page 1 of 7 Part 1 General 1.1 DESCRIPTION OF WORK.1 The work described herein shall consist of the construction of a wetwell as shown on the Plans and in accordance with Section 01001,
SCHEDULE OF AMENDMENTS
SEQ Water Supply and Sewerage Design & Construction Code SEQ Accepted Infrastructure Products and Materials SCHEDULE OF AMENDMENTS Amendment No.12 October 2018 October 2018 SEQ D&C Code Schedule of Amendments
MATERIAL/MANUFACTURER SPECIFICATIONS FOR DISTRIBUTION WATER MAINS AND APPURTENANCES
MATERIAL/MANUFACTURER SPECIFICATIONS FOR DISTRIBUTION WATER MAINS AND APPURTENANCES REVISION April 2008 1 MATERIAL SPECIFICATIONS T.S. 1 GENERAL Materials incorporated in the finished work and used during
TAPPING SADDLES DN 40 - DN 450
TAPPING SADDLES 0-0 FAST, PERMANENT TAPPING SOLUTION FOR BOTH RIGID AND FLEXIBLE PIPE TYPES FEATURES bodies are manufactured from either stainless steel or Ductile Iron Fusion Bonded Epoxy coated (depending
If you require plastic pipe products that are not listed here, please contact Iplex Pipelines for further information.
IPLEX - The Company Iplex Pipelines is a major Australasian manufacturer and distributor of a wide range of plastics-based pipeline systems for the civil, mining, plumbing, irrigation, gas, telecommunications,
UNIVERSITY OF MISSOURI Hydronic Energy Distribution 2016 Q1
GENERAL: The scope of this document is to provide instruction for the installation and testing of chilled water piping installed for the University of Missouri. DESIGN GUIDELINES: 1. Materials 1.1. Pipe
CITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER
CITY OF WARRENVILLE STANDARD SPECIFICATIONS WATER MAIN, SANITARY SEWER AND STORM SEWER WATER MAIN 1. All open cut water main shall be polyvinyl chloride plastic (PVC) pressure pipe per AWWA specification
WATER 6.1 GUIDELINES
6-1 6.0 WATER 6.1 GUIDELINES The requirements of the Queensland Water Resources Commission Guidelines for Planning and Design of Urban Water Supply Schemes shall be followed in general. The requirements
PART A : CPVC PIPES AND FITTNGS (EXTERNAL WATERSUPPLY):
PART A : CPVC PIPES AND FITTNGS (EXTERNAL WATERSUPPLY): 01 Providing and Fixing of CPVC pipes confirming to ASTM standard including all CPVC fittings like tees, elbows, bends, unions, coupling, reducer
Terrain HDPE. Product Guide
TAGIG1-PT JULY 2009 Terrain HDPE Product Guide Terrain HDPE BBA BRITISH BOARD OF AGRÉMENT CERTIFICATE No. 07/4479 A modern high density polyethylene system with many advantages over cast iron and other
AVK FITTING SOLUTIONS
AVK FITTING SOLUTIONS AVK FITTING SOLUTIONS AVK FITTING SOLUTIONS FOR WATER AND WASTE WATER The AVK Group is one of the leading manufacturers of valves and fittings within the water, gas, waste water,
Date: 13/04/2015 1:14:38 PM
Date: 13/04/2015 1:14:38 PM Cad File No: J:\500-Cad-data\Standard_Drawings\Flow Systems\FSI-1000-FS_On-Lot Infrastructure Installation Set Out Details.dwg Date: 25/02/2015 11:18:14 AM Cad File No: J:\500-Cad-data\Standard_Drawings\Flow
Sewerage Code WSA Addendum PART 3 STANDARD DRAWINGS
Addendum to the Water Industry Technical Standards and National Codes of Practice DOCUMENT W2 Sewerage Code WSA 02-1999 Addendum PART 3 STANDARD DRAWINGS Gippsland Water Business Management System Detailed
The Viking Johnson range of MaxiFit products - High tolerance pipe couplings - MAXIFIT
Including Large Diameter MaxiFit The Viking Johnson range of MaxiFit products - High tolerance pipe couplings - MAXIFIT Overview MaxiFit High tolerance pipe couplings B A C The Viking Johnson range of
The system: it supports 3 load classes (A15, B125, C250) in compliance with Standard EN 1433
The system: it supports 3 load classes (A15, B125, C250) in compliance with Standard EN 1433 it is made up of a channel - entirely made from HD-PE - which needs no strengthening frame it has a wide usable
HAWLE-range of products
HAWLE-pRODucTS All OvER ThE world since 1948 HAWLE-range of products HAWLE subsidiaries HAWLE partners Illustrations, technical data, dimensions and weights are subject to alteration without notice. Edition
Pipe OD. KT1-075T0?? in the typical specifying. offtake size as shown
Tapping s - PN OPERATING PRESSURE rigid and flexible pressure pipe RIGI-TAP FLEXI-TAP VARI-TAP Pipe 0 0 0 00 0 00 0 00 0 00 0 RIGID PIPE FLEXIBLE PIPE DICL Steel CICL AC ABS* GRP* RC PVC HDPE MSCL GWI
SECTION FACILITY SANITARY SEWERS
PART 1 - GENERAL 1.01 SECTION INCLUDES A. Gravity-flow, non-pressure sanitary sewerage outside the building, with the following components: 1.02 DEFINITIONS 1. Cleanouts. 2. Precast concrete manholes.
SPECIFICATION FOR TUBULAR STEEL LIGHTING COLUMN. Reference is made in this Specification to the following:
SPECIFICATION FOR TUBULAR STEEL LIGHTING COLUMN 1. SCOPE This specification covers the design, fabrication and testing of tubular section, galvanised steel friction fit jointed street light columns of
Changes for the. TOHOPEKALIGA WATER AUTHORITY Standards, Specifications and Details
Changes for the 2017 TOHOPEKALIGA WATER AUTHORITY Standards, Specifications and Details The following changes are made to the existing standards and details to clarify or improve existing information.
HDPE Pipe Fittings PIPE & FITTING SYSTEMS
HDPE Pipe Fittings PIPE & FITTING SYSTEMS 1 The Plastics Experts. AGRU Pipe & Fitting Systems offer a complete range of high-quality pipes, fittings, valves and customized components made from polyethylene.
Storm Drainage
University of New Hampshire University of New Hampshire Scholars' Repository Division 33 Utilities Chapter 5 Technical Construction and Renovation Standards 4-23-2015 334100 - Storm Drainage Sandra Hickey
Material Supply Standard
Material Supply Standard Date: 01 June 2018 is uncontrolled when copied or printed Page 1 of 165 Revision Description By Date 1 First release J de Villiers Principal Engineer Standards 1.1 Material updates
SECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
SECTION 21 05 00 COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 - GENERAL 1.1 SUMMARY A. This section supplements all sections in this division, including pipe, fittings, valves, and connections for sprinkler
Whakatane District Council Chapter 6 Engineering Code of Practice CHAPTER 6 WATER SUPPLY
CHAPTER 6 WATER SUPPLY CHAPTER 6 WATER SUPPLY PART 1 DESIGN 6.1.1 INTRODUCTION This chapter sets out the basic design principles for the provision of reticulation for the supply of water. While some construction
CHAPTER 4 PIPES. Prof. Dr. Uğur Atikol
CHAPTER 4 PIPES Prof. Dr. Uğur Atikol History Materials: Lead used to be very popular material due to its availability, durability and ease of working. It had environmental problems Industrial developments
SECTION VIBRATION CONTROLS FOR PLUMBING PIPING AND EQUIPMENT
Page 220548-1 SECTION 220548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY PIPE HANGERS, Section PIPE HANGERS, SUPPORTS, AND RESTRAINTS
PART 1 GENERAL 1.01 SUMMARY Section 15140 PIPE HANGERS, This Section includes the furnishing and subsequent installation of: A. Pipe and equipment hangers, supports, and associated anchors B. Equipment
A. Gravity-Flow, Nonpressure, Drainage-Piping Pressure Rating: 10-foot head of water (30 kpa).
SECTION 221313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
SECTION 027 SPECIFICATIONS - PIPE MATERIALS FOR SEWERS
SECTION 027 SPECIFICATIONS - PIPE MATERIALS FOR SEWERS Pipe material used to construct, repair or modify sewers shall conform to the specifications within this Section. 1.0 Clay Pipe Construction of clay
SECTION 200 SANITARY SEWER MATERIAL SPECIFICATIONS
SECTION 200 SANITARY SEWER MATERIAL SPECIFICATIONS 200-1 MATERIAL SPECIFICATION LIST Rev. May 2011 SEWER UTILITY General: 1. All manufacturers products listed are preferred. Others may be submitted to
TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II
SECTION 221313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
SECTION PLUMBING PIPING
SECTION 22 1000 PLUMBING PIPING PART 1 GENERAL 1.1 QUALITY ASSURANCE A. Perform Work in accordance with authority having jurisdiction standards. Utilize products as indicated in drawings and as allowed
Pipe. Valves. Fittings. Fasteners. Tube and Tube Fittings. And Much More
Pipe Valves Fittings Fasteners Tube and Tube Fittings And Much More Tubing Sizes Materials 1/16" to 6" Diameter Stainless A269 & A511 Copper Monel Inconel Hastelloy DK Lok Tube Fittings Sizes Products
SAINT PETERSBURG CITY COUNCIL. Consent Agenda. Meeting of April 3, The Honorable James Bennett, Chair and Members of City Council
SAINT PETERSBURG CITY COUNCIL Consent Agenda Meeting of April 3, 2008 To : The Honorable James Bennett, Chair and Members of City Council Subject : Renewing a strategic partnership agreement with HD Supply
ENGINEERING STANDARDS MANUAL SECTION 6 WATER SUPPLY
CODE OF PRACTICE FOR CITY INFRASTRUCTURE & LAND DEVELOPMENT ENGINEERING STANDARDS MANUAL SECTION 6 WATER SUPPLY Issue 4.6 Sept 2008 Section 6 Page 1 SECTION 6.0 WATER SUPPLY 6.1 SCOPE This Section of the
PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 02630 - STORM DRAINAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
AS Supplement Engineering survey and engineering survey design drawing. Amend: Vehicular traffic Category V) lighting.
STANDARDS AS 2566.1:1998 AS 3680:1989 AS/NZS 1100.401:1984 AS/NZS 1158 V3 Plastics Pipelaying Design AS 2566.1 Supplement 1 1998 Polyethylene sleeving for ductile iron pipelines. Engineering survey and
SANITARY SEWERS. B. Construct or relocate building sanitary sewer services, stubs, and connections.
SANITARY SEWERS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Sanitary Sewer Gravity Mains B. Sanitary Sewer Force Mains C. Sanitary Sewer Services 1.02 DESCRIPTION OF WORK A. Construct sanitary sewer gravity
8. WATER SUPPLY AND RETICULATION
8. WATER SUPPLY AND RETICULATION 8.1 General This section covers the Kaipara District Council requirements for the design and construction of water supply services and associated structures. Water supply
2. A preconstruction meeting with the TWA s staff is required prior to initiating construction.
General: 1. Construct utilities in accordance to TWA approved plans and shop drawings. Any deviation from the approved plans shall be approved by the DEVELOPER S ENGINEER and TWA 2. A preconstruction meeting
Effective Date: Revision #: 1. Section K: Miscellaneous. Casing Insulators/ Stainless Steel. Polyethylene Encasement.
K 1 K 2 K 3 K 4 K 5 K 6 K 7 K 8 K 9 Casing Insulators/ Stainless Steel Polyethylene Encasement Manhole Inserts Pipe Saddle Support/ Valve Vaults/ Adjustable Cylindrical Wall Seals & Line Sleeves Metal
SECTION SANITARY SEWERAGE PART 1 GENERAL 1.01 RELATED DOCUMENTS
SECTION 02530 - SANITARY SEWERAGE PART 1 GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
SECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
Page 230548-1 SECTION 230548 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
A. Gravity-Flow, Nonpressure, Drainage-Piping Pressure Rating: 10-foot head of water.
SECTION 22 1313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
Ductile Iron Pipes (Socket & Spigot Pipes)
Ductile Iron Pipes (Socket & Spigot Pipes) Al-Saad Engineering Consulting Pipeline supply a High Quality and specifications with good Prices for the customers. The Range of Diameter that Al-Saad Engineering
Class 125S/200WOG Bronze Gate Valve Non-Rising Stem, Threaded Ends Testing: BS EN 12288, BS 5154, BS EN Working Pressure: PN16
Class 125S/200WOG Bronze Gate Valve Non-Rising Stem, Threaded Ends Testing: BS EN 12288, BS 5154, BS EN 12266 Working Pressure: PN16 FIG. 201 WORKING PRESSURE Working Pressure Non-Shock (psi) Saturated
MANHOLES, VAULTS AND CATCH BASINS SECTION A. Section Soil and Aggregate Materials. C. Section Storm Drainage Systems
SECTION 02607-1 1.0 GENERAL 1.1 SCOPE: A. This section covers the work necessary for the construction of sanitary and storm system manholes, catch basins, and miscellaneous concrete structures complete.
PLASTIC FITTINGS Avenue Edmonton, AB Canada T6E 5Z7. Toll Free: Phone: (780) Fax: (780)
9333 45 Avenue Edmonton, AB Toll Free: 1-800-272-9693 Phone: (780) 436-1930 Fax: (780) 435-4849 info@can-con.com TABLE OF CONTENTS PLASTIC FITTINGS POLYETHYLENE PIPE...- 1 - SERVICE RISERS... - 3 - TRANSITION
SECTION TAPPING SLEEVES AND VALVES
SECTION 33 12 16.17 TAPPING SLEEVES AND VALVES PART 1: GENERAL 1.01 SCOPE Furnish, install and test all tapping sleeves, tapping valves, and tapping saddles as shown on the Drawings. 1.02 RELATED WORK
NELSON CITY COUNCIL INFRASTRUCTURAL ASSETS SD 601 APPROVED SENIOR EXECUTIVE INFRASTRUCTURE
SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 601 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 602 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 603 SENIOR EXECUTIVE INFRASTRUCTURE DATE SD 604 NOTES 1. PRE-FORMED PLASTIC
EXPRESSION OF INTEREST (EOI) FOR. Mechanical Works
EXPRESSION OF INTEREST (EOI) FOR Mechanical Works KWtE-03-PR-EO-ACC-0 Rev01 15 Version: Date: Prepared by: Approved: 01 7/11/18 VMC AMN Page 1 OF 6 1 Project overview ACCIONA s Engineering, Procuring &
List of products of harmonised standards Code 28: PIPES-TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION
List of products of harmonised standards Code 28: PIPES-TANKS AND ANCILLARIES NOT IN CONTACT WITH WATER INTENDED FOR HUMAN CONSUMPTION EN 295-1 Part 1: Requirements for pipes, fittings and joints Vitrified
LinerGrip Pipeline Rehabilitation System
Enhanced LinerGrip Pipeline Rehabilitation System For use with Polyethylene Pipe Liners PIONEERS IN PIPE SOLUTIONS LinerGrip Overview A Bespoke Solution to Enhance Pipeline Rehabilitation In an attempt
Water & Industrial Products Catalog
Water & Industrial Products Catalog www.smith-blair.com info@smith-blair.com Phone: 800..9705 or 870.77.527 After Hours Number: 90.277.998 Fax: 800.8.792 or 870.77.52 EMERGENCY PHONE 90.277.998 In the
CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 602 MARCH 1993 CONSTRUCTION SPECIFICATION FOR THE INSTALLATION OF ELECTRICAL CHAMBER 602.01 SCOPE 602.02 REFERENCES 602.05 MATERIALS TABLE OF CONTENTS
12.1 MUELLER TAPPING MATERIALS AND SPECIALTY VALVES. MUELLER Tapping Sleeves and Crosses. MUELLER Tapping Valves. MUELLER Stainless Steel Tapping
MUELLER TAPPING MATERIALS AND SPECIALTY VALVES 12.1 Shaded area indicates change Rev. 7-16 MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including
American Flow control 2-12 Series 2500
American Flow control 2-12 Series 2500 Resilient wedge gate valve FLOW CONTROL Construction Ductile iron operating nut Provides strength and durability. Upper O-ring seals Can be replaced while the valve
Installation instructions. LORO-ATTIKASTAR siphonic drains
instructions with clamping flange, for pressure flow for bituminous or plastic roof sealing sheets, according to EN 1253, steel, hot-dip galvanised consist of the drain body and the stainless steel suction
SECTION UTILITY POLYETHYLENE CONTAINMENT PIPE SYSTEMS
SECTION 02670 UTILITY POLYETHYLENE CONTAINMENT PIPE SYSTEMS PART 1 - GENERAL 1.01 WORK INCLUDED A. Trenching and other excavation. B. Ground water control. C. Pipe bedding. D. Installation of containment
Date of update January 25, 2018 Valid until
CERTIFICATE PRODUCT APPLICATION VTT-C-4805-09 Date of update January 25, 2018 Valid until 12.10.2020 U Protect fire insulation solutions for ventilation ducts MANUFACTURER Saint-Gobain Finland Oy / ISOVER
SECTION STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY 1.2 SUBMITTALS 1.3 PROJECT CONDITIONS
SECTION 334100 - STORM UTILITY DRAINAGE PIPING PART 1 - GENERAL 1.1 SUMMARY Section Includes: 1. Pipe and fittings. 2. Drain Basin. 3. De-chlorination tablet feeder. 4. Non-pressure transition couplings.
LANE ENTERPRISES, INC. STANDARDS & SPECIFICATIONS
LANE ENTERPRISES, INC. STANDARDS & SPECIFICATIONS The following pages are an index of standards and specifications associated with Lane products. For quick reference purposes, Lane products are shown below
SEWER FORCE MAIN HDPE PIPE
SECTION 15150 SEWER FORCE MAIN HDPE PIPE PART 1: GENERAL 1-1 DESCRIPTION: This specification governs the material, pipe, fittings, joining methods and general construction practice for High Density Polyethylene
BILL OF QUANTITY ENGINEERING & MANAGEMENT CONSULTING CENTRE. "Beit Hanoun Emergency Water Supply Project"
"Beit Hanoun Emergency Water Supply Project" " Rehabilitation and Construction of Beit Hanoun Water Network " BILL OF QUANTITY ENGINEERING & MANAGEMENT CONSULTING CENTRE Bill of Quantities PREAMBLE TO
FLAT. The system: it supports 3 load classes (A15, B125, C250) in compliance with Standard EN 1433
The system: it supports 3 load classes (A15, B125, C250) in compliance with Standard EN 1433 it is made up of a channel - entirely made from HD-PE - which needs no strengthening frame it has a wide usable
ELECTRICAL CONTRACTORS THE UNIVERSITY OF TENNESSEE KNOXVILLE, TENNESSEE SECTION PAGE 1 SECTION SUPPORTING DEVICES
KNOXVILLE, TENNESSEE SECTION 26 05 29 PAGE 1 PART 1 - GENERAL: 1.01 DESCRIPTION OF WORK: SECTION 26 05 29 A. Extent of supports, anchors, sleeves and seals is indicated by drawings and schedules and/or
THOMAS. Buffalo Saddles. Tap In Products PIPE PRODUCTS. Universal Live Tap In Saddles for All Rigid Pipe Materials.
THOMAS PIPE PRODUCTS Tap In Products Buffalo Saddles Universal Live Tap In Saddles for All Rigid Pipe Materials A1 TAP IN PRODUCTS KITWE VALLEY - Copper Belt Province - Zambia PROJECT Kitwe Valley Pivot
Independent certification of your products & services. 2.2 Relevant Standards 1. SCOPE
1. SCOPE This schedule specifies requirements for the AquaSpira CSR (Composite Steel Reinforced) pipe system as manufactured by AquaSpira Limited. It is applicable for underground gravity drains, sewer
SECTION HANGERS AND SUPPORTS FOR PLUMBING
SECTION 22 05 29 HANGERS AND SUPPORTS FOR PLUMBING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
Ø mm. SYSTEM KAN-therm. High quality for reasonable price TECHNOLOGY OF SUCCESS ISO 9001
Ø 16 110 mm SYSTEM KAN-therm PP High quality for reasonable price TECHNOLOGY OF SUCCESS Contents 3 System KAN-therm PP The material... 94 Sanitary systems installation... 95 Pipes... 95 Thermal elongation...
SECTION BASIC FIRE SUPPRESSION MATERIALS AND METHODS. A. Section includes pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - BASIC FIRE SUPPRESSION MATERIALS AND METHODS PART 1 GENERAL 1.1 SUMMARY A. Section includes pipe, fittings, valves, and connections for sprinkler systems. B. Related Sections: 1. Section
Diffused Aeration Piping Equipment
1.0 General 1.1. The specifications in this section include all components of the Diffused Aeration System with the exception of the individual diffuser units. Refer to additional specification sections
Dŵr Cymru Welsh Water s Self-lay Policy for Water Mains and Services July 2015
Dŵr Cymru Welsh Water s Self-lay Policy for Water Mains and Services July 2015 Introduction This Self-Lay Policy applies when a developer decides to self-lay water mains and services (ie. construct water
City of Port Moody. Water Meter Specifications
City of Port Moody Water Meter Specifications Engineering Division, Updated December 2015 City of Port Moody Water Meter Specifications 1. Preamble... 3 2. Definitions... 3 3. Services to be Metered...
STANDARD CONSTRUCTION DETAILS SANITARY SEWER REVISED MARCH 2018 DEPARTMENT OF ENGINEERING
STANDARD CONSTRUCTION DETAILS REVISED MARCH 2018 GENERAL NOTES EMBEDMENT DETAILS EMBEDMENT DETAILS TWO-WAY CLEANOUT - EXISTING LATERAL TWO-WAY CLEANOUT - NEW CONSTRUCTION TYPICAL SEWER HOUSE SERVICE CONNECTION
NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 0548 - PIPING AND EQUIPMENT PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
D-1 FIRE PROTECTION PRODUCTS TAPPING VALVE. MUELLER Tapping Valves. MUELLER Tapping Sleeves and Crosses. MUELLER Stainless Steel Tapping Sleeves
TAPPING VALVE MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including cast iron, ductile iron, A-C, and cast iron O.D. PVC--Also outlet sealed
APPLICABILITY TABLE. Council BSC CHRC GRC IRC LSC MRC RRC Applicable Yes Yes Yes Yes Yes Yes Yes
Precast roof slabs refer Standard Drawing CMDG-D-03 Special cast iron cover and frame, refer Service Authority. Special cast iron cover and frame, refer Service Authority. Cast iron cover and frame Ø 200
B. Fiberglass for construction in back lot easements placed on cast-in-place base.
Section 02083 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Fiberglass manholes for unpaved areas placed on top of a precast base to form a manhole. B. Fiberglass for construction in back lot easements
SECTION (15150) - SANITARY WASTE AND VENT PIPING
SECTION 22 13 16 (15150) - SANITARY WASTE AND VENT PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Pipe Materials. 2. Fittings. 3. Joining Materials. B. Related Sections: 1.02 REFERENCES 1.
SPECIFICATIONS - DETAILED PROVISIONS Section Stainless Steel Sluice Gates C O N T E N T S
SPECIFICATIONS - DETAILED PROVISIONS Section 11294 - Stainless Steel Sluice Gates C O N T E N T S PART 1 - GENERAL... 1 1.01 SUMMARY... 1 1.02 REFERENCES... 1 1.03 DEFINITIONS... 1 1.04 DESIGN REQUIREMENTS...
WATER SUPPLY CODE SCHEDULE OF AMENDMENTS
SEQ Water Supply and Sewerage Design & Construction Code (SEQ WS&S D&C Code) WATER SUPPLY CODE SCHEDULE OF AMENDMENTS Amendment No.2 December 2018 December 2018 SEQ WS&S D&C Code Water Supply Code - Amendment