APPROVED MATERIALS AM-7 WATER SUPPLY TABLE OF CONTENTS. Table 7: Water Supply...2

Size: px

Start display at page:

Download "APPROVED MATERIALS AM-7 WATER SUPPLY TABLE OF CONTENTS. Table 7: Water Supply...2"

Erick Watkins
6 years ago
Views:

1 APPROVED MATERIALS AM-7 WATER SUPPLY TABLE OF CONTENTS Table 7: Water Supply...2

2 Table 7: Water Supply Materials that are not on the following table MUST be approved by Council refer to AM-1 General Provisions. Note: All parts of the water supply system in contact with drinking water shall be designed using components and materials that comply with AS/NZS 4020 AM-7. 1 Water Bulk water mains: larger than 200mm Ø. These to be specifically approved and specified by Council. Principal mains: 100mm, 150mm and 200mm Ø either upvc or PE. Rider mains: 50mm Ø (ID PVC), 63mm Ø (OD MDPE/PE 80). Services : 20mm, 25mm, 40mm and 50mm Ø. AM Spiral-welded Steel AM Ductile Iron Class K9 AM Ductile-iron pipe, light cement lined Tyton Excel PN20 and PN35 Generally (but not limited to) bulk mains unless other wise approved Bulk mains unless other wise approved Bulk mains unless other wise approved NZS 4442 or AS1579 AS/NZS 2280 and AS/NZS 2280 and Rubber ring joints and Polyken YG111 external wrapping or Speed Steel with polyethylene coatings. Internal Linings include concrete, epoxy and galvanised. Light cement lined with Tyton joints. External protection with greensleeve. Generally suspended pipes and high structural loadings. With Tyton Joint elastomeric seals and socket/spigot joints (with blue polyethylene sleeving) not for use in high water table areas. Licence #SMK0883 Steelpipe Zealand Tubemakers Australia New of AM PVC s and Fittings Bulk, principal and rider AS/NZS 1477 Coloured white. Iplex s New Page 2 Updated 01/07/2014

3 for pressure applications mains Joints shall be spigot and socket rubber ring type (Z joint). Solvent cement joint shall not be used. AM upvc Bulk, principal and rider mains AM mpvc RRJ AM Polyethylene (MDPE) PE80, PN12.5, SDR 11 Bulk, principal and rider mains Mains up to and including 100mmØ (125mm OD) Iplex Licence #SMK RX Plastics License Tel.Lic0001 Joints shall be spigot and socket rubber ring type (Z joint). Solvent cement joint shall not be used. Zealand Marley RX Plastics Iplex Licence #SMK RX Plastics License Tel.Lic0001 AS/NZS 1477 Joints shall be spigot and socket rubber ring type (Z Iplex s New joint). Solvent cement joint shall not be used. Zealand Marley New RX Plastics AS/NZS 4765: Series 2 AS/NZS 4130 and s shall be butt or fusion welded in accordance with the manufacturer s recommendations, and the standard coloured blue or blue jacket. Unrestrained mechanical couplers can be used where appropriate and meets relevant NZ standard. Iplex Licence #SMK P20400 RX Plastics Licence SMKP New Iplex s New Zealand Marley New RX Plastics Iplex s New Zealand Marley New RX Plastics Waters and Farr Hynds AM Polyethylene (HDPE) PE100 PN12.5, SDR 13.6 AM Copper Tube 20 50mm half-hard Mains 150mmØ (180mm OD) and greater. AS/NZS 4130 and s shall be butt or fusion welded in accordance Iplex s New with the manufacturer s recommendations, and the Zealand standard coloured blue or blue jacket. Marley New Hynds Unrestrained mechanical couplers can be used where appropriate and meets relevant NZ standard. RX Plastics Waters and Farr Iplex Licence #SMK P20400 RX Plastics Licence SMKP BPD on service mains NZS 3501 For use with RPZ backflow prevention devices only. Mico Metals Page 3 Updated 01/07/2014

4 AM-7.2 Seal Rings Comply with AS Elastomeric seals for waterworks purposes AM-7.3 Fittings AM Cast-iron Socket and Spigot Fittings Cast-iron Flanges AM Ductile-iron pipe Flanged, Socket and Spigot Fittings Flanges AM Stand-alone Flanges AM Bolts, Nuts and Washers to be hot-dipped galvanised AM Stainless Steel Bolts, Nuts and Washers are acceptable alternatives to hot-dipped galvanised fastenings, provided they Flanges to be to AS/ with required pressure (PN) rating to be specified. Flange coatings to be to AS/NZS Flanges to be to AS/ with required pressure (PN) rating to be specified. Flange coatings to be to AS/NZS Flanges to be to AS/ or AS 2129 (for mild steel) with required pressure (PN) rating to be specified. Flange coatings to be to AS/NZS AS/NZS 1111 and 1112 Complying with AS 1252 high-strength steel fastenings Rated at PN16 or higher. Epoxy coated. PVC, ductile- or cast-iron. Steel and Tube - Unflanged adaptor - Ductile Iron This particularly applies for use in corrosive soil conditions. NZ Channel Forms Page 4 Updated 01/07/2014 Gillies Metaltech HJ Asmus & Company Limited Crevet s Hygrade Products Iplex s New Zealand Marley New Steel and Tube Holdings Limited who meets the required standard who meets the required standard Hynds

5 AM AM are 316-grade stainless steel with factory applied molybond coating Gibaults - Cast-iron (coating as per standard) - M stainless steel, (with clips fusion coating as per standard) Unrestrained Mechanical Couplings - Ductile-iron (nylon coating as per standard) - M grade stainless steel barrel, (with clips fusion coating as per standard) AM MDPE Fittings - Electro Fusion - Butt Fusion - Mechanical <50mm Up to 200mm DI barrels and backing rings or SS barrels with DI backing rings. Above 200mm note in item and Use 316-grade stainless steel bolts as a preference. Coating to ASTM Use 316-grade stainless steel fasteners. A276 AS/NZS 4158 AS/NZ 4998 AS/NZS 4158 AS/NZ 4129 Use hot-dipped galvanised bolts as per or 316-grade stainless steel bolts. Use 316-grade stainless steel fasteners. Agru Butt welding and Electro fusion Fittings. "Plassim" MDPE Fitting to AS/NZS 4129 Lic No: WMKA21062 "Magnum" MDPE Fitting to AS/NZS 4129 Lic No: SMK02432 Viking Johnson Aqua fast, Aqua grip and Ultra grip Mechanical Fittings for Polyethylene. Hawle System 2000 Mechanical Fittings for Polyethylene. Innogaz Marley License #1271 Plasson Licence #1494 and 1271 Gillies Metaltech Viking Johnson Maxifit (with Sheraplex coated bolts) Crevet s Milnes Pty Gillies Metaltech Viking Johnson Crevet s Milnes Pty AVK Australia Pty (recommended for Gibaults >200 mm (ID)) Iplex s New Zealand Marley New Plasson Waters & Farr Page 5 Updated 01/07/2014 Hynds Hynds Asmuss Plastic Limited Hygrade Products RX Plastics Iplex s New Zealand

6 Asmuss Alprene A16 Easygrip Licence #1157 Plasson Series One Pushfit Fitting Hawle HAKU Saddle No.5250 AM Brass Fittings alloy 486 AM Manifold AM Ferrules: Gunmetal polyethylene fittings with AS ASTM B Recommend New Zealand manufacturer due to variability of imported materials. Acuflo GM900STR Bronze Manifold Assembly Acuflo CM2000 Composite Manifold Spartan Engineering Co. Acuflow Industries WBoPDC only AM Gaskets Potable Water Supply fittings AM-7.4 Valves Garlock 2500 Gasket Garlock Sealing Industries Bay Engineers Blackwoods Paykels Page 6 Updated 01/07/2014

7 AM Sluice Valves 80mm resilient seated anti-clockwise closing rated at PN16 External and internal protective coating Flanges to be raised face and drilled as per standard AM Gate Valves 25mm and 40mm Bulk, principal and rider mains AM Gate Valve 50mm Rider mains and connections AM Butterfly Valves AM-7.5 AM Fire Hydrants Tall pattern screw-down standard clockwise closing, rated to PN16 or higher Coated as per standard AM-7.6 Tapping Bands and Saddles AS/NZS NZS/BS 5163 Class1 AS/NZS 4158 and Flanges to be to AS/ with required pressure (PN) rating to be specified. Flange coatings to be to AS/NZS 4158 Teflon gland packing or 2 or more O ring seals and dust cover. In-line valves shall be the same diameter as the reticulation main. Licence #PRD/R61/0412/2 Hawle Licence #SMK20123 AVFI Non-Rising Stem Resilient Valve DN375 BS 5154 or AS 1628 Clock-wise closing dezincification-resistant materials or LG2 gunmetal, PN16 or higher. Gillies Metaltech Crevet s Hawle AVK Australia Pty Hygrade Products Page 7 Updated 01/07/2014 & Infrastructure KITZ Corporation (Lic #WMKA02054) Pegler Hattersley & (Lic #1850) Infrastructure KITZ Corporation License #WMKA02054 Pegler Hattersley License #1850 NZS/BS 5163 Clock-wise closing, resilient seating. Hawle (Licence WMKA 20123) AVK Australia Pty NZS/BS 750 AS/NZS 4158 and. Standards Australia MP52 Specific design and approval O ring sealing system. Drain holes for frost protection are not permitted. The use of ball hydrants is not permitted. Crevet s Hydravalve Gillies Metaltech Hawle & Infrastructure Tudor Supplies Co & Infrastructure AM mm-200mm AS/NZS 4793 / Tapping bands should be 25mm or greater for live Milnes Pty

8 AM-7.7 LG2 gunmetal DR type, fully enclosed Polyethylene type, fully enclosed with stainless steel bolts Water meters AM mm Manifold Meters MP52 Spec025 OMIL R49-1 tapping. Fully enclosed for mpvc blue brute, superblue, cast iron and spiral steel (AC sizing). Swivel bolt type with a flexible band for existing AC water main. Milnes Pty Licence #W134 Milnes Pty Series GM60A Milnes Pty Series 61 Maintenance Milnes Pty insulated type for ductile, cast or steel mains Licence #W134 Giltech Precision Castings Plasson Licence #1494 Meters must be rated Q3 = 2.5m3/hr and must have a minimum R value (Q3/Q1) of 160. Meters must be capable of transmitting a pulse output (for the purposes of data logging or remote reading). Construction shall be dezincification-resistant (DR) brass to NZS/AS 3688 or Construction of composite materials subject to approval of material specification. Giltech Castings Plasson Precision Elster/Kent Sensus Actaris Pty Sapel Aquadis A.D Riley and Co. DEECO Services Chatswood Trading Pty Page 8 Updated 01/07/2014

9 AM mm Inline Meters OMIL R49-1 Meters will be rated Q3 = 6.3 m3/hr and must have a minimum R value (Q3/Q1) of 160. Meters must be capable of transmitting a pulse output (for the purposes of data logging or remote reading). Construction shall be dezincification-resistant (DR) brass to NZS/AS Elster/Kent Sensus Actaris Pty Sapel Aquadis A.D Riley and Co. DEECO Services Chatswood Trading Pty AM mm Inline Meters OMIL R49-1 Meters will be rated Q3 = 16 m3/hr. and must have a minimum R value (Q3/Q1) of 160. Meters must be capable of transmitting a pulse output (for the purposes of data logging or remote reading). Construction shall be dezincification-resistant (DR) brass to NZS/AS AM Inline Meters >50mm OMIL R49-1 Specific design and approval Design information shall be provided for approval and shall include the design flow rates (minimum, average, maximum), proposed meter make/model and manufacturers specification. Elster/Kent Sensus Actaris Pty Sapel Aquadis A.D Riley and Co. DEECO Services Chatswood Trading Pty ABB A.D Riley and Co. DEECO Services Chatswood Trading Pty Page 9 Updated 01/07/2014

10 AM-7.8 Tracer Wire AM Tracer Wire AM Warning Tape / Detection Tape Trenchless Installation Rising Mains Open Cut Installation A continuous 4.0mm2 multi-strand (minimum of 4) polythene sleeved cable. Width - 100mm (min.) Thickness 80mu Printing TBC Printing Height 80mm Tape Colour - TBC Polymark Packaging AM-7.9 Boxes (Valve, Fire Hydrant, Meter), Packers and Valve Marker Plate Cast-iron/ductile-iron NZS/BS750 Hydrant cast box to NZS/BS750. Valve cast box - to Council Standard Drawings. Valve Marker Plate - WBoPDC only Hygrade Products AM-7.10 Concrete Products AM Concrete Valve / Hydrant Marker Post To Council Standard Drawings. Williamson Creative Products Newstead Concrete Products Page 10 Updated 01/07/2014

11 AM Fire Hydrant Concrete Surrounds AM Valve Surrounds AM-7.11 Wooden Products Concrete To Council Standard Drawings. To Council Standard Drawings. AM Wooden Valve Post WBoPDC Only To Council Standard Drawings. AM-7.12 Toby Boxes Cast iron Polyethylene AM-7.13 Backflow Prevention Devices To Council Standard Drawings. AS/NZ Types and classification of devices to meet Council requirements as assessed. For dedicated fire systems, use Verifire standard. Surecast Metals Chevron Industries 2001 Acuflow Industries Draper Enterprises Reliance Worldwide Acuflow Hygrade Products Hydroflow Distributors Deeco Services Hynds Page 11 Updated 01/07/2014

APPROVED MATERIALS AM-6 WASTEWATER TABLE OF CONTENTS. Table 6: Wastewater...2

APPROVED MATERIALS AM-6 WASTEWATER TABLE OF CONTENTS Table 6: Wastewater...2 Table 6: Wastewater Materials that are not on the following table MUST be approved by Council refer to AM-1 General Provisions.