POLY-GIB COUPLINGS DN 90 - DN 180
|
|
|
- Marilynn Barker
- 6 years ago
- Views:
Transcription
1 POLY-GIB COUPLINGS DN 90 - DN 180 RESTRINED MECHNICL COUPLING FOR CONNECTING TO HDPE PIPE FETURES The Poly-Gib range comes in a variety of configuration. Straight couplings, stepped couplings, flange adaptors and blank ends The Poly-Gib range of restrained couplings can be installed without the need to disassemble. significantly improving speed and ease of installation No internal stiffener required in application on HDPE pipe of SDR 11 or less Nitrile rubber seals suitable for potable water, waste water and oil/gas applications Fasteners feature a captive head configuration enabling single spanner installation Stainless steel components made from 316SS, that has been fully pickled and passivated Three bolt design is used in sizes up to DN 180 to improve installation in the field Components are pre-lubricated during assembly to assist installation Tapping pads on the blank end products permit a drain, flush or sampling point to be added to the system Manufacturing facility certified to ISO 9001 Quality ssured Standard DESCRIPTION PPLICTION TECHNICL DT Poly-Gib Mechanically Restrained Couplings, Flange daptors and Blank Ends provide an effective method for connecting HDPE pipe to new and existing pipe infrastructure The Poly-Gib range utilises a mechanical restraint and sealing system that is not effected by the presence of water, dirt or other contaminates, making it ideal as a universal coupling system The Poly-Gib straight and stepped couplings are ideal for connecting two HDPE pipes as either part of a new installation or as part of a pipe repair Poly-Gib Flange daptors are ideal for connecting HDPE pipe to flanged fittings or valves and are particularly useful in installing new valves into existing pipelines Poly-Gib Blank Ends provide an effective end cap that does not require thrust blocks to secure. The ability to complete an onsite tapping in the side and end of the cap is very useful in providing domestic connections, pressure testing new line or water sampling Poly-Gib Couplings are suitable for potable water, raw water, waste water and oil/gas applications. If used on gas applications, approval must be obtained from the asset manager before installation Size Range: DN 90 - DN 180 Maximum Operating Pressure: 1600 kpa Temperature Range: -10 C to 60 C Relevant Standards: S/NZS 129: Fittings for polyethylene (PE) pipes for pressure applications StandardsMark Licence Certificate No SMK0080 Not applicable to Stepped Couplings
2 STRIGHT POLY-GIB COUPLINGS Flange OD Bolt detail Barrel lengt Bolt length Pipe insertion depth Barrel DN Qty Size B C Minimum 90 KR0090DCS M DI KR0110CS M SS KR0125CS M SS KR0160CS M SS KR0180CS M SS 10.3 PPROX PRTS LIST 1 Barrel Ductile iron / S stainless steel / STM 20M 2 Flanges Ductile iron S Gaskets Nitrile (NBR) compound S 166 and S 020 Grippers Copper alloy S 235 and BS Bolts 316 stainless steel SECTION - 6 Washers 316 stainless steel 7 Nuts 316 stainless steel S Coating Fusion bonded epoxy ON DUCTILE IRON PRTS S/NZS 158
3 STEPPED POLY-GIB COUPLINGS Flange OD Bolt detail Barrel length Bolt length Pipe insertion depth Barrel DN Small Large Quantity Size B C Minimum 90 / 110 KRS DCS M DI / 125 KRS DCS M DI / 125 KRS CS M SS / 160 KRS DDS M DI / 180 KRS DDS M DI / 160 KRS DDS M DI / 180 KRS DDS M DI / 180 KRS CS M SS 10. PPROX PRTS LIST 1 Barrel Ductile Iron / S Stainless Steel / STM 20M 2 Flanges Ductile Iron S Gaskets Nitrile (NBR) Compound S 166 and S 020 Grippers Copper lloy S 235 and BS Bolts 316 Stainless Steel SECTION - 6 Washers 316 Stainless Steel 7 Nuts 316 Stainless Steel S Coating Fusion Bonded Epoxy ON DUCTILE IRON PRTS S/NZS 158
4 POLY-GIB FLNGE DPTER Flange OD Bolt detail Barrel length Bolt length Pipe insertion depth Barrel DN Qty Size B C Minimum 110 KRF0110F100DCS M DI KRF0125F100DCS M DI KRF0160F150DCS M DI KRF0180F150DCS M DI 13.8 PPROX PRTS LIST SECTION Body Ductile iron BRREL & FLNGE S Coupling Ductile iron flange S Gasket Nitrile (NBR) compound S 166 and S 020 Gripper Copper alloy S 235 and BS Bolts 316 stainless steel 6 Washers 316 stainless steel 7 Nuts 316 stainless steel S Coating Fusion bonded epoxy ON DUCTILE IRON PRTS S/NZS 158
5 POLY-GIB BLNK END Flange OD Bolt detail Barrel length Bolt length Pipe insertion depth Barrel DN Quantity Size B C Minimum 90 KRB0090DS M DI KRB0110DS M DI KRB0125DS M DI KRB0160DS M DI KRB0180DS M DI 12. PPROX. 1 SECTION PRTS LIST 1 Barrel Ductile iron / S stainless steel / STM 20M 2 Flanges Ductile iron S Gaskets Nitrile (NBR) compound S 166 and S 020 Grippers Copper alloy S 235 and BS Bolts 316 stainless steel 6 Washers 316 stainless steel 7 Nuts 316 stainless steel S Coating Fusion bonded epoxy ON DUCTILE IRON PRTS S/NZS 158
6 CLMPS & COUPLINGS WNG is one of the leading manufacturers and suppliers of Grade 316 Stainless Steel Repair and Tapped Clamps as well as Couplings for reticulated water, sewerage and gas mains including industrial piping systems. WNG products have become synonymous with quality and reliability. Our product range is widely utilised and relied upon by Water uthorities and Councils throughout ustralia in the installation and maintenance of their supply mains and reticulation network. KWIK CLMPS WNG products can be sourced through a range of international distributors, their details can be found on our web site. Quality ISO 9001 HDPE CLMPS TPPED CLMPS full circle repair clamp for small bore galvanised steel, copper and PVC pipe. DN 15 - DN 50 range of Flanged, Tapped and Repair Clamps specifically for HDPE pipe installations. DN 0 - DN 600 reliable means of tapping into old, unstable or damaged pipe. DN 50 - DN 1200 TPPING SDDLES FLNGED OFFTKE CLMPS SEWER OB JUNCTION CLMPS Permanent tapping solution for both rigid and flexible pipe. DN 0 - DN 50 cost effective means of achieving a T connection or under pressure tapping. DN DN 900 quick method of installing a new property service connection on a sewer main. DN DN 50 VRI GIB COUPLINGS HIGH PRESSURE COUPLINGS SOCKET JOINT LEK CLMPS Non-restrained mechanical couplings for connecting pipes with equal or unequal diameters. DN 0 - DN 1200 Provides a mechanical joint between similar or dissimilar pipes in high pressure environments. DN DN 2000 Provide a permanent and economical seal over a leaking socket-spigot joint. DN 80 - DN 1200 WNG COMPONENTS CNR GIBSON STREET & SNDFORD ROD, WNGRTT, VICTORI 3677 PHONE / FX EMIL sales@wang.com.au - WEB wang.com.au ll WNG trademarks and logos are owned by Wang Components, ll other brand or product names are trademarks or registered marks of their respective owners. Because we are continuously improving our products and services, Wang Components reserves the right to change specifications without prior notice P Wang Components. ll Rights Reserved.
TAPPING SADDLES DN 40 - DN 450
TAPPING SADDLES 0-0 FAST, PERMANENT TAPPING SOLUTION FOR BOTH RIGID AND FLEXIBLE PIPE TYPES FEATURES bodies are manufactured from either stainless steel or Ductile Iron Fusion Bonded Epoxy coated (depending
WANG TAPPING SADDLES. fast, permanent tapping SOLUTION FOR BOTH rigid and flexible pipe types FEATURES DESCRIPTION APPLICATION TECHNICAL DATA
WANG TAPPING SADDLES 0-0 fast, permanent tapping SOLUTION FOR BOTH rigid and flexible pipe types FEATURES bodies are manufactured from either stainless steel or Ductile Iron Fusion Bonded Epoxy coated
Features PAGE 1-2. Wide Range Restrained End Cap
www.romac.com 1-800-426-9341 RESTRINED JOINT RESTRINED JOINT Features PGE 1-2 Wide Range Restrained oupling ORIGINLLY RELESED IN THE SUMMER OF 2013, THE OUPLING INSTLLS IN OUT THREE MINUTES, ND OMMODTES
UL / FM D-1 FIRE PROTECTION PRODUCTS TAPPING VALVE. MUELLER Tapping Sleeves and Crosses. MUELLER Tapping Valves
UL / FM TAPPING VALVE SECTION Rev. 2-15 MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including cast iron, ductile iron, A-C, and cast iron O.D.
12.1 MUELLER TAPPING MATERIALS AND SPECIALTY VALVES. MUELLER Tapping Sleeves and Crosses. MUELLER Tapping Valves. MUELLER Stainless Steel Tapping
MUELLER TAPPING MATERIALS AND SPECIALTY VALVES 12.1 Shaded area indicates change Rev. 7-16 MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including
D-1 FIRE PROTECTION PRODUCTS TAPPING VALVE. MUELLER Tapping Valves. MUELLER Tapping Sleeves and Crosses. MUELLER Stainless Steel Tapping Sleeves
TAPPING VALVE MUELLER Tapping Sleeves and Crosses Full range of Tapping Sleeves and Crosses to fit most types of pipe including cast iron, ductile iron, A-C, and cast iron O.D. PVC--Also outlet sealed
SECTION POLYVINYL CHLORIDE (PVC) WATERLINE
SECTION 02632 POLYVINYL CHLORIDE (PVC) WATERLINE PART 1 - GENERAL 1.01 SCOPE OF WORK A. Furnish all labor, materials, equipment, and incidentals required, and install polyvinyl chloride (PVC) waterline,
SECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS (PRESSURE PIPE)
SECTION 02623 HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS (PRESSURE PIPE) PART 1 - GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment and incidentals required and install high density
SEWER FORCE MAIN HDPE PIPE
SECTION 15150 SEWER FORCE MAIN HDPE PIPE PART 1: GENERAL 1-1 DESCRIPTION: This specification governs the material, pipe, fittings, joining methods and general construction practice for High Density Polyethylene
PROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
Series 2000PV Mechanical Joint Restraint for PVC Pipe
Series 2000PV Mechanical Joint Restraint for PVC Pipe Features and Applications: For restraining plain end PVC pipe at mechanical joint fittings and appurtenances Sizes 3 inch through 36 inch Sizes 42
Technical Manual PE PIPE SYSTEM MAINTENANCE GUIDE ISSUE 1.1
Technical Manual PE PIPE SYSTEM MAINTENANCE GUIDE ISSUE 1.1 Ref: TM001 28 June 2008 Disclaimer In formulating this manual PIPA has relied upon the advice of its members and, where appropriate, independent
This section includes materials and installation of ductile-iron pipe and fittings for potable and recycled water systems.
NORTH MARIN WATER DISTRICT STANDARD SPECIFICATIONS SECTION 15056 DUCTILE-IRON PIPE AND FITTINGS PART 1 GENERAL 1.01 DESCRIPTION This section includes materials and installation of ductile-iron pipe and
SECTION HIGH DENSITY POLYETHYLENE PIPE AND FITTINGS
SECTION 02620 PART 1 GENERAL 1.1 SCOPE OF WORK A. Furnish all labor, materials, equipment, and incidentals required to install High Density Polyethylene (HDPE) pressure pipe, fittings, and appurtenances
SPECIFICATIONS - DETAILED PROVISIONS Section Plastic (PVC) Pressure Water Pipe & Fittings C O N T E N T S
SPECIFICATIONS - DETAILED PROVISIONS Section 15064 - Plastic (PVC) Pressure Water Pipe & Fittings C O N T E N T S PART 1 - GENERAL... 1 1.01 REQUIREMENT... 1 1.02 DELIVERY... 1 1.03 QUALITY ASSURANCE...
AMERICAN FLOW CONTROL 2"-12" SERIES 2500 RESILIENT WEDGE GATE VALVE
AMERICAN FLOW CONTROL 2"-12" SERIES 2500 RESILIENT WEDGE GATE VALVE CONSTRUCTION DUCTILE IRON OPERATING NUT Provides strength and durability. UPPER O-RING SEALS Helps isolate the lubrication chamber as
HAWLE-range of products
HAWLE-pRODucTS All OvER ThE world since 1948 HAWLE-range of products HAWLE subsidiaries HAWLE partners Illustrations, technical data, dimensions and weights are subject to alteration without notice. Edition
2. A preconstruction meeting with the TWA s staff is required prior to initiating construction.
General: 1. Construct utilities in accordance to TWA approved plans and shop drawings. Any deviation from the approved plans shall be approved by the DEVELOPER S ENGINEER and TWA 2. A preconstruction meeting
Couplings The Perfect Through Wall Connection
Specialist Wall Couplings The Perfect Through Wall Connection pipe CONNECTIONS, repair & flow control products for the utilities industry Wall Couplings Overview The Perfect Solution for Passing Pipes
SECTION C1 DUCTILE IRON PIPE AND FITTINGS GENERAL
SECTION C1 DUCTILE IRON PIPE AND FITTINGS GENERAL This section covers the furnishing and installation of ductile iron water pipe, fittings, thrust restraint and pipe disinfection. Ductile Iron Pipe MATERIALS
Dobbie Dico Meter Co (WA) Pty Ltd PRODUCT APPRAISAL REPORT 1622
WSAA Product Appraisal 1622 1 Dobbie Dico Meter Co (WA) Pty Ltd PRODUCT APPRAISAL REPORT 1622 Dobbie Resilient Seated Gate Valves DN 100 to DN 250 AS/NZS 2638.2:2011 Gate valves for waterworks purposes
PART 5 WATER SYSTEMS
PART 5 WATER SYSTEMS Abbreviations and Symbols Plan 501 Abbreviations and symbols for water... 205 Concrete Boxes and Hardware 502 27" Frame and cover... 207 503 38" Frame and cover... 209 505 Concrete
Sclairpipe VERSATILE HIGH DENSITY POLYETHYLENE PIPE
Sclairpipe VERSATILE HIGH DENSITY POLYETHYLENE PIPE Sclairpipe Sclairpipe high density polyethylene (HDPE) pipe represents the latest advances in both material and manufacturing techniques. Since 1968,
SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION DUCTILE IRON PIPE, FITTINGS AND SPECIAL ITEMS
SUB WATER DEPARTMENT STANDARD CONSTRUCTION SPECIFICATIONS TABLE OF CONTENTS SECTION 33 11 13.13 DUCTILE IRON PIPE, FITTINGS AND SPECIAL ITEMS PART 1 GENERAL... 3 1.1 Description... 3 1.2 Reference Specifications,
Daytona Beach Pier Building Renovation Jun 2010
SECTION 15150 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
CULINARY WATER SYSTEMS
CULINARY WATER SYSTEMS I. Water system size determination A. The minimum water line size is 8 inch for distribution lines in a residential subdivision. 1. Subdivisions that have a school or church will
TCC/SHORE TRANSIT BUS MAINTENANCE FACILITY - PHASE II
SECTION 221313 - FACILITY SANITARY SEWERS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
American Flow control 2-12 Series 2500
American Flow control 2-12 Series 2500 Resilient wedge gate valve FLOW CONTROL Construction Ductile iron operating nut Provides strength and durability. Upper O-ring seals Can be replaced while the valve
4 1 /2 MARK 73-5 AMERICAN FLOW CONTROL. It s What We Know. AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING 4 1 /2 MARK 73-5 FIRE HYDRANT
AMERICAN-DARLING FIRE HYDRANT AMERICAN-DARLING FIRE HYDRANT AMERICAN FLOW CONTROL It s What We Know. CONSTRUCTION AMERICAN-DARLING FIRE HYDRANT OPERATING NUT Cast one-piece bronze operating nut. Design
(For compliance with the new sewers for adoption regulation or building regulations part H1)
Plastic Drainage Keyline offers a comprehensive range of products suitable for all building, foul, surface water and land drainage applications - including new innovative, cost-effective systems for compliance
B. Drainage Piping: Building sewer piping outside building that conveys storm drainage from building.
SECTION 221316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
INTRODUCTION. PVC PRESSURE PIPE SPECIFICATIONS The SANS 966 is a two-part specification.
1 INTRODUCTION DPI Plastics (Pty) Ltd is a leading manufacturer of PVC and HDPE water reticulation and drainage pipe and fitting systems with two ISO 9001 certified South African factories based in Johannesburg
Innovation in Joint Restraint Systems for PVC Pressure Pipe and Fittings. Clean & Safe Drinking Water Workshop. Wednesday, March 25, 2015
Innovation in Joint Restraint Systems for PVC Pressure Pipe and Fittings Clean & Safe Drinking Water Workshop Wednesday, March 25, 2015 Thrust forces Gasketed joints are made to seal and not to restrain,
CONSTRUCTION SPECIFICATION FOR WATERMAIN INSTALLATION IN OPEN CUT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 441 APRIL 2017 (Formerly OPSS 441, November 2014 Note: The PROV implemented in April 2017 replaces OPSS 441 COMMON, November 2014 with no technical
MASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 22 PLUMBING
SECTION 221316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following soil and waste, sanitary drainage and vent piping inside the building: 1. Pipe, tube,
Section 3 Fusible PVC Pipe Connections
3.0 Fusible PVC pipe is joined together using butt-fusion joints, however, it may be necessary to utilize other connections to integrate Fusible PVC pipe sections into an overall pipe system. There are
A. This Section includes sanitary waste and vent piping inside the building and to locations indicated.
SECTION 221316 SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
Terrain HDPE. Product Guide
TAGIG1-PT JULY 2009 Terrain HDPE Product Guide Terrain HDPE BBA BRITISH BOARD OF AGRÉMENT CERTIFICATE No. 07/4479 A modern high density polyethylene system with many advantages over cast iron and other
DUCTILE IRON PIPE AND FITTINGS
Section 02501 PART 1 G E N E R A L 1.01 SECTION INCLUDES A. Ductile iron pipe and fittings for water lines, wastewater force mains, gravity sanitary sewers, and storm sewers. 1.02 MEASUREMENT AND PAYMENT
NORTH HARRIS COUNTY REGIONAL WATER AUTHORITY. Section DUCTILE IRON PIPE AND FITTINGS
Section 02501 PART 1 GENERAL 1.01 SUMMARY This Section includes ductile iron pipe and fittings for water lines, wastewater force mains, gravity sanitary sewers, and storm sewers. 1.02 MEASUREMENT AND PAYMENT
WATER 6.1 GUIDELINES
6-1 6.0 WATER 6.1 GUIDELINES The requirements of the Queensland Water Resources Commission Guidelines for Planning and Design of Urban Water Supply Schemes shall be followed in general. The requirements
NORTHWESTERN UNIVERSITY PROJECT NAME JOB # ISSUED: 03/29/2017
SECTION 22 1316 - SANITARY WASTE AND VENT PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
PRODUCT GUIDE. C.A. Baldwin & Co Ltd. Quality is our strength
PRODUCT GUIDE C.A. Baldwin & Co Ltd Quality is our strength INDEX Expansion / Anti-vibration Couplings Pages 1 7 Repair Bandage Page 8 Fixing and Repair Clamps Pages 9 19 Compression Fittings for Steel
CONSTRUCTION SPECIFICATION FOR SEWAGE FORCEMAIN INSTALLATION IN OPEN CUT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 412 NOVEMBER 2009 CONSTRUCTION SPECIFICATION FOR SEWAGE FORCEMAIN INSTALLATION IN OPEN CUT TABLE OF CONTENTS 412.01 SCOPE 412.02 REFERENCES 412.03
CONSTRUCTION SPECIFICATION FOR WATERMAIN INSTALLATION IN OPEN CUT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 441 NOVEMBER 2010 CONSTRUCTION SPECIFICATION FOR WATERMAIN INSTALLATION IN OPEN CUT TABLE OF CONTENTS 441.01 SCOPE 441.02 REFERENCES 441.03 DEFINITIONS
SANITARY SEWERS. B. Construct or relocate building sanitary sewer services, stubs, and connections.
SANITARY SEWERS PART 1 - GENERAL 1.01 SECTION INCLUDES A. Sanitary Sewer Gravity Mains B. Sanitary Sewer Force Mains C. Sanitary Sewer Services 1.02 DESCRIPTION OF WORK A. Construct sanitary sewer gravity
Material Specification for. Large Diameter Watermains
Engineering & Construction Services Division Standard Specifications for Sewers and Watermains TS 7.80 November 2016 Large Diameter Watermains Table of Contents TS 7.80.01 SCOPE... 2 TS 7.80.01.01 Application...
PIPE OUTSIDE DIAMETER GUIDE
August 17, 2017-1 PIPE OUTSIDE DIAMETER GUIDE PIPE OUTSIDE DIAMETER GUIDE - SMALL DIAMETER PIPE SIZES NOMINAL PIPE SIZES 1 /2" 3 /4" 1" 1 1 /4" 1 1 /2" 2" 2 1 /2" THIS O.D. GUIDE IS FOR YOUR CONVENIENCE
SECTION DUCTILE IRON FITTINGS. A. This section includes materials, installation, and testing of ductile iron fittings 48 inches and smaller.
PART 1 - GENERAL 1.1 DESCRIPTION A. This section includes materials, installation, and testing of ductile iron fittings 48 inches and smaller. 1.2 RELATED WORK SPECIFIED ELSEWHERE A. Section 01300 Record
Systems. Puriton Price List. Barrier pipe and fittings system Protecting drinking water through contaminated land
Systems Puriton List Barrier pipe and fittings system Protecting drinking water through contaminated land March 2018 Systems Puriton Barrier pipe & fittings system The barrier pipe system of choice for
UNI-BELL PVC PIPE ASSOCIATION UNI-B-15-10
UNI-BELL PVC PIPE ASSOCIATION UNI-B-15-10 RECOMMENDED STANDARD SPECIFICATION FOR POLYVINYL CHLORIDE (PVC) FABRICATED PRESSURE FITTINGS November 2010 UNI-BELL PVC PIPE ASSOCIATION 2711 LBJ Freeway, Suite
HDPE Pipe Fittings PIPE & FITTING SYSTEMS
HDPE Pipe Fittings PIPE & FITTING SYSTEMS 1 The Plastics Experts. AGRU Pipe & Fitting Systems offer a complete range of high-quality pipes, fittings, valves and customized components made from polyethylene.
SECTION WATER DISTRIBUTION
SECTION 33 10 00 WATER DISTRIBUTION PART 1 GENERAL 1.01 SUMMARY 1.02 CODES A. Section Includes: 1. Underground water service piping, watermains and appurtenances. A. All work shall comply with the most
Table of Contents. Section Pipe and Fittings Section Includes Description of Work Submittals 1. 1.
Table of Contents Section 5010 - Pipe and Fittings Page No. Part 1 - General 1.01 Section Includes 1 1.02 Description of Work 1 1.03 Submittals 1 1.04 Substitutions 1 1.05 Delivery, Storage, and Handling
VALVE PRODUCT OVERVIEW
WATER MANAGEMENT VALVE PRODUCT OVERVIEW WATER MANAGEMENT Double Eccentric BFV DEX Main Specification Double Eccentric BFV DEX Model Body Disc Shaft Retaining ring Internal bolts External bolts Bearing
ProSeal Flex Couplings
ProSeal Flex Couplings Stainless Steel Shielded Transition Couplings designed for resistance to shear forces as well as corrosion. Pasco s ProSeal Flex Couplings allow the plumber to make a wide variety
Diffused Aeration Piping Equipment
1.0 General 1.1. The specifications in this section include all components of the Diffused Aeration System with the exception of the individual diffuser units. Refer to additional specification sections
SECTION TAPPING SLEEVES AND VALVES
SECTION 33 12 16.17 TAPPING SLEEVES AND VALVES PART 1: GENERAL 1.01 SCOPE Furnish, install and test all tapping sleeves, tapping valves, and tapping saddles as shown on the Drawings. 1.02 RELATED WORK
AVK MORE THAN MEETS THE EYE EXPECT US TO EXCEED MARKET STANDARDS
AVK MORE THAN MEETS THE EYE EXPECT US TO EXCEED MARKET STANDARDS DURABILITY AND RELIABILITY ABOVE AND BELOW GROUND Product development and quality control Wedge and resilient rubber vulcanization Durability
BULLETIN MARCH DeZURIK VPB V-PORT BALL VALVES TECHNICAL SPECIFICATIONS
BULLETIN.00-2 MRCH 20 ezurik VPB V-PORT BLL VLVES TECHNICL SPECIFICTIONS 2 20 ezurik, Inc. Materials of Construction Flanged Construction 1 20" (25 500mm) Class 0 1 (25 300mm) Class 300 etailed (Enlarged)
AVK NEDERLAND INDUSTRIAL VALVES & FITTINGS MAKING A DIFFERENCE INDUSTRIAL 1
AVK NEDERLAND INDUSTRIAL MAKING A DIFFERENCE INDUSTRIAL 1 AVK NEDERLAND INDUSTRIAL AVK Group The AVK Group is a privately owned industrial group that currently comprises 90 companies. AVK s core business
1.2 ACTION AND INFORMATIONAL SUBMITTALS.1 Provide submittals in accordance with Section Submittal Procedures.
BID OPPORTUNITY NO. 253-2011 PAGE 1 OF 7 PART 1 GENERAL 1.1 REFERENCES.1 American Society of Mechanical Engineers (ASME).1 ASME B31.1, Power Piping, B31.3 Process Piping, B31.9 Building Services Piping..2
Improvements to the Distribution Pipe Lines in Zalengi, Central Darfur Please insert the currency Item Description
RETURNABLE BID SCHEDULE 4 BILL OF QUANTITIES Case No. SDPC/76613/WORKS/ITB056 Improvements to the Distribution Pipe Lines in Zalengi, Central Darfur Please insert the currency 1 General 1 Mobilization
ARTICLE 29 SANITARY SEWER FORCE MAINS
SANITARY SEWER FORCE MAINS Index 29.01 GENERAL 29.02 DESIGN CRITERIA 29.03 MATERIALS 29.04 VALVES 29.05 INSTALLATION 29.06 IDENTIFICATION 29.07 HYDROSTATIC TESTING BACK TO TABLE OF CONTENTS Section 29.01
STANDARD SPECIFICATIONS SECTION PRESSURE SEWER SYSTEM 1.2 REQUIREMENTS FOR MANUFACTURERS AND SUPPLIERS BEFORE DELIVERY
STANDARD SPECIFICATIONS SECTION 02533 PRESSURE SEWER SYSTEM PART 1 GENERAL 1.1 DESCRIPTION A. Section includes requirements to provide permanent grinder pump pressure sewer system, piping, and appurtenances.
Series 1100 Mechanical Joint Restraint for Ductile Iron Pipe
MEGALUG Series 1100 Mechanical Joint Restraint for Ductile Iron Pipe Features and Applications: Sizes 3 inch through 54 inch Constructed of ASTM A536 Ductile Iron Torque Limiting Twist-Off Nuts Nominal
Series A-C Single Stage Double Suction Large Split Case. TECHNICAL Brochure BAC9100
Series A-C 9100 Single Stage Double Suction Large Split Case TECHNICAL Brochure BAC9100 TABLE OF CONTENTS Useful Pump Formulas 2 Pump Engineering Data 3 Materials of Construction 4 Exploded View 6 USEFUL
ROOF DRAINS TABLE OF CONTENTS
Pictorial Index Product Recommendations Roof Drain Selection Factors Sizing Placement Material & Characteristics Pipe Connection Commonly Specified Options Typical Installations TABLE OF CONTENTS ROOF
Dŵr Cymru Welsh Water s Self-lay Policy for Water Mains and Services July 2015
Dŵr Cymru Welsh Water s Self-lay Policy for Water Mains and Services July 2015 Introduction This Self-Lay Policy applies when a developer decides to self-lay water mains and services (ie. construct water
Operating Instructions
Operating Instructions A-2600 SERIES AWWA SWING CHECK VALVE 500 West Eldorado Street Decatur, Illinois 62522 www.muellercompany.com! WARNING! 1. Read and follow all pertinent instructions carefully. Proper
Ref RESILIENT SEAT GATE VALVE ISO PN10-16 F4. Model/Ref:
Model/Ref: 180-181 - 182 www.lauridsenindustri.com Size : Ends : Min Temperature : Max Temperature : DN 40 to DN 600 ISO PN10/16 flanges - 10 C + 110 C with EPDM wedge Max Pressure : 16 Bars up to DN400,
7. Allowable Fittings.
7. Allowable Fittings. a. General Requirements. 1) The fittings listed in this section are generally the allowable fittings for the design of DIP and PVC pipe. For steel pipe and fittings, see Part One,
Romacon-korjausliittimet
Solutions for power transmission Romacon-korjausliittimet www.konaflex.fi Romacon Repair Clamp Type RS-0 Romacon stainless steel repair clamps Style RS-0 are used for permanent repairs of broken and damaged
G-FIRE GROOVED COUPLINGS
G-FIRE GROOVED COUPLINGS Figure 5 G-FIRE Rigid Page 5 Figure 5 Flexible Page GRINNELL are designed for grooved end pipe and are available in nominal sizes of 25mm (") to 3mm (2") including BS, and ISO
SECTION 18. AMERICAN General Index
SECTION 18 AMERICAN General Index General Index A Abbreviations Organizations...1-1 Standard, American...17-23 Abrasion Resistant Pipe...12-12 Accessories (See Joint Materials) American Flow Control Valves
Facility Sanitary Sewers
University of New Hampshire University of New Hampshire Scholars' Repository Division 22 Plumbing Chapter 5 Technical Construction and Renovation Standards 4-23-2015 221313 - Facility Sanitary Sewers Sandra
SECTION PLUMBING PIPING
SECTION 22 10 00 PLUMBING PIPING PART 1 GENERAL 1.1 SCOPE A. Work consists of all plumbing work indicated on drawings and specified herein. B. Included are requirements for fees/permits for installation
STATE UNIVERPROGRAM DIRECTIVES
DIRECTIVE 15H-10 PIPING TYPES AND MATERIALS Issue date: September 2017 Steam & Condensate Piping Service & Location Pipe Size Pipe Material & Weight Joint Type Fitting Material Insulation Material Low
SECTION PVC DISTRIBUTION PIPE (AWWA C900 & C905)
SECTION 402092 PVC DISTRIBUTION PIPE (AWWA C900 & C905) PART 1 - GENERAL A. Description This section includes materials, installation, and t esting of polyvinyl chloride (PVC) distribution pipe conforming
FIBERBOND DECK DRAINS
ENGINEERED COMPOSITE PIPING SYSTEMS DECK DRAINS www.fiberbond.com www.futurepipe.com DRAIN SERIES: Drain Selection and Installation Guide The drains contained in this booklet are available in the following
ONE PIPE LENGTH MAX (REFER TO 1/4"/FT SLOPE (MIN) 5'-0" (MIN) OR 4" LATERAL NOTE #1) INCREASER RIGHT-OF-WAY/ 4"x6" REFER TO TYPICAL EXCAVATION,
VENT CAP (MUSHROOM TYPE) SOLID CAP EXIST GRADE MIN BUILDING REFER TO NOTE #4 MIN CONCRETE SIDEWALK CURB OR EDGE OF SIDEWALK STREET CLEANOUT (REFER TO NOTE #3) VENT PIPE 4" PVC 6" PVC CLEANOUT CONCRETE
Universal Transition Coupling
TECHNICL MNUL METRIC/IMPERIL Universal Transition Coupling Committed to sustainable development, Philmac is well renowned for quality products and services. Philmac manufactures pipe fittings NT ccredited
ADDENDUM NO. 1. Mallory Valley Utility District Technical Specifications & Design Criteria for Water Supply & Distribution Facilities
ADDENDUM NO. TO Mallory Valley Utility District Technical Specifications & Design Criteria for Water Supply & Distribution Facilities Date of Addendum: December, 00 Hethcoat & Davis, Inc. 78 Franklin Road,
CHAPTER 3 - PRESSURE IRRIGATION
CHAPTER 3 - PRESSURE IRRIGATION 3.1 GENERAL This division covers furnishing and installing pressure pipe as shown on the Drawings or established in the field, and all flushing, testing, repairing, as required
SECTION PIPE & PIPE FITTINGS PART 1 GENERAL
SECTION 02610 PIPE & PIPE FITTINGS PART 1 GENERAL 1.01 DESCRIPTION A. This Section includes the material and bedding requirements for all pipe and pipe fittings for underground pressure and non-pressure
PERFORMANCE PIPE DRISCOPLEX 4000/4100 Pipe Water and Wastewater Piping Systems
PERFORMANCE PIPE DRISCOPLEX 4000/4100 Pipe Water and Wastewater Piping Systems Corrosion Resistant Leak Proof Fused Joints Ideal for Trenchless Applications Flexible Hydraulically Efficient Will Not Tuberculate
Fully Structural Renewal of 39-inch PCCP Water Transmission Main with Swagelining and HDPE
Caribbean Water & Wastewater Conference 2015 Topic: Water & Wastewater Pipeline Rehabilitation, Trenchless Technology Fully Structural Renewal of 39-inch PCCP Water Transmission Main with Swagelining and
2017 Material and Construction Specifications
2017 Material and Construction Specifications Water and Sewer Pre Construction Materials Standard Details Inspections & Testing Todd Marti, Director of Engineering South West, West Valley City, UT T: E:
Amendment to OPSS 493 (Nov 2015) Construction Specification for Temporary Potable Water Supply Services
Engineering & Construction Services Division Standard Specifications for Sewers and Watermains TS 493 September 2017 Amendment to OPSS 493 (Nov 2015) Construction Specification for Temporary Potable Water
Materials Carbon Steel is used in the manufacturing of riser and pipe clamps. Stainless Steel and other materials are available.
Pipe clamps offered in this section are designed for support and attachment of pipe to structural members. wide range of pipe clamps are available for various applications. Materials arbon Steel is used
PVC Fittings & Laterals for Solid-Wall PVC Sewer Pipe
Design and Installation Guide PVC Fittings & Laterals for Solid-Wall PVC Sewer Pipe TABLE OF CONTENTS Introduction 2 Products 3 Main-Line Fittings & Service-Line Fittings 3-4 Connections to Dissimilar
Metaval Consolidated Pty Ltd
WSAA Product Appraisal PA 1112 Issue 2 1 1. 2 Metaval Consolidated Pty Ltd PRODUCT APPRAISAL REPORT 1112 Part 1 Issue 2 VAG BAIO plus System Restrained Joint Ductile Iron Fittings for PE and ISO sized
IS First edition
INTERNATIONAL STANDARD IS0 7005-2 First edition 1988-12-15 INTERNATIONAL ORGANIZATION FOR STANDARDIZATION ORGANISATION INTERNATIONALE DE NORMALISATION MEXflYHAPOAHAfl OPTAHMA~Mfl I-IO CTAHflAPTMA~MM Metallic
The Uncloggable Roof Drain Dome LIT-058
www.mifab.com ROOFGUARD -018 CERTIFIED MANAGEMENT SYSTEM ISO 9001:015 Go to www.mifab.com for the most current product specification sheets. DESIGNED, ASSEMBLED AND PACKAGED IN THE USA The Uncloggable
Clay County Utility Authority Approved Materials " "
Clay County Utility Authority " "" Clay County Utility Authority "". "". " Clay County Utility Authority DESCRIPTION: Extruded sheets or panels with integral male/female sliding lock connection ends.
C900/RJ. CertainTeed. PVC Pipe. with CertainTeed s proven Certa-Lok restrained joint system. Directional Drilling
1 1 CertainTeed C900/RJ PVC Pipe with CertainTeed s proven Certa-Lok restrained joint system Directional Drilling Underground Water Mains and Restrained, Non-Metallic Change-of-Direction Fittings (No Thrust
PASSAIC COUNTY TECHNICAL INSTITUTE CCA 1422 NEW S.T.E.M. BUILDING 2017
SECTION 02630 - STORM DRAINAGE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
NOTICE OF DISCONTINUATION,
Sizes ", ", ", 6", 8", " NOTICE OF DISCONTINUATION, Effective May st Mueller Systems is discontinuing our current line of strainers. We will continue to offer our plate strainers on a first come, first
FUSIBLE PVC PIPE SYSTEMS Fusible C-900 Fusible C-905 FPVC
Fusible C-900 Fusible C-905 FPVC Installations Trenchless Horizontal directional drilling Sliplining Pipe bursting Jack-and-bore carrier pipe Open-Cut Applications Features and Benefits Gasketless, leak-free,
THE REGIONAL MUNICIPALITY OF PEEL STANDARD SPECIFICATIONS FOR WATERMAINS
THE REGIONAL MUNICIPALITY OF PEEL STANDARD SPECIFICATIONS FOR WATERMAINS INDEX Page No. W.1. GENERAL...1 W.2 SCOPE...2 W.3 MATERIALS...2 W.3.1 General... 2 W.3.2 Concrete... 2 W.3.3 Pipe Bedding and Backfill