Always. Reliable. Tight. CATALOGUE CABLE ENTRIES.

Transcription

1 Always. Reliable. Tight. CATALOGUE CABLE ENTRIES

2 Solutionworld CABLE. PIPE. BUILDING ENTRY. ALWAYS. RELIABLE. TIGHT. Electricity, telecommunication, water, waste water, gas or district heating - whenever a perfectly safe sealing of building entries is required, Hauff-Technik offers the best possible solution. Innovative cable and pipe entries, building entries and trenchless house connections of professional quality. All from one source. Out of the box or customized products. For highest efficiency, user-friendliness and longevity in all buildings. From single-family homes to complex major projects. Always Hauff. Always reliable. Always tight. 2

3 Application tachometer TO DETERMINE YOUR SPECIFIC REQUIREMENTS S e l e c t i o n c r i t e r Application: non-standing seepage water, soil humidity, rain water, splash water, waterproof concrete stress class 2 pressing water, waterproof concrete stress class 1 Application: standing seepage water, ground water, strata water, i a f o r c a b l e a nd pipe bar, installation depth 0 1 m s e a l s - d e p e n d bar, installation depth 0 3 m 0 > 0.3 bar, installation depth 0 >3 m requirement i n g o n s p e c i f i c r e qui Application: shock loads, high stress (chemical, thermal), r e m e n t s difficult installation conditions PRODUCTS ACCORDING TO LOAD CASES DIN 18195/STRESS CLASS WATER- PROOF CONCRETE, EXAMPLE USED IS PRESS SEAL FOR CABLES Product group Sealing width Catalogue page HRD 1 30 mm 36 HRD SG 40 mm 32 HRD 2 60 mm 38 Please note: Wall inserts and flanges must be used in compliance with DIN and/or EN206-1! 3

4 Overview wall structure/sealing of building entries BASIS TO DETERMINE THE APPROPRIATE CABLE AND PIPE ENTRY SYSTEMS Wall type basement/ Wall structure Sealing according to DIN Part 4, Soil humidity and non-standing seepage water Sealing according to DIN Part 6, Standing seepage water and pressing water No. 1 brick-built basement No. 5 wall brick-built basement wall Brick-built basement wall sealing on outside of building sealing on outside of building No. 2 No. 6 concreted basement concreted basement Concreted basement sealing on outside of building sealing on outside of building No. 3 No. 7 double wall/ element wall double wall/ element wall Double wall/element wall sealing on outside of building sealing on outside of building Double wall/element wall with thermal insulation No. 4 No. 8 thermal insulation double wall/ element wall sealing on outside of building thermal insulation double wall/ element wall sealing on outside of building WATERPROOF CONCRETE ACCORDING TO EN206-1 Concreted basement with waterproof concrete Concreted basement with waterproof concrete and thermal insulation Double wall/element wall with waterproof concrete Double wall/element wall with waterproof concrete and thermal insulation No. 9 No. 10 No. 11 No. 12 concreted concreted basement basement thermal insulation double wall/ element wall thermal insulation double wall/ element wall If you do not find your wall structure among above examples, kindly let us have a sketch. 4

5 Catalogue CONTENT CABLE ENTRIES CABLE SEALING SYSTEM 150 Wall inserts and plastic flange 6 9 System covers and system sealings for cables System covers for the connection of cable ducts Cable entry system Cable entries Accessories 21 CABLE SEALING SYSTEM 90 Wall inserts and aluminium flange System covers for cables System covers for the connection of cable ducts Cable entry system Accessories 31 PRESS SEALS CABLE PRESS SEALS Press seals Standard press seals Individual press seals (closed and split) WALL SLEEVES EXTRA Standard wall sleeves/wall sleeves with flanges Extra EARTHINGS FIRE PROTECTION ROOF ENTRIES FOUNDATION PIPES GENERAL SALES TERMS AND DELIVERY CONDITIONS General Terms of Business 5

6 Cable sealing system 150 HSI 150 VARIA CABLE ENTRY WITH ADJUSTABLE LENGHT SETTING APPLICATION: Waterproof concrete stress class 1 Cable entry HSI 150-K2 Varia: infinitely adjustable to the required wall thickness on-site plug-in frame system for block assembly on-site connection of system sealing possible on both sides insert of system covers for sealing of cables and connection of smooth and corrugated ducts available for double walls/element walls Cable entry HSI 150-GSM Varia: stepless adjustment to the required wall thickness on site plug-in frame system for block assembly on-site connection of system sealing possible on one side; there is also an integrated plug-in socket for the connection of smooth cable ducts 210 mm Frame size 220 x 220 mm 430 mm adjustable length mm Connection of cable entry system KES-M 150 Connection of stiff cable ducts Sealing with system cover HSI 150-DG HSI 150-GSM Varia fixed as package 6

7 Cable sealing system 150 HSI 150 VARIA CABLE ENTRY WITH ADJUSTABLE LENGHT SETTING HSI 150 VARIA CABLE ENTRY Item Cable entry HSI 150 Varia Cable entry HSI 150 Varia Suitable for wallthickness (in mm) Article code Article number Picture HSI 150-K2- Varia/ HSI 150-K2- Varia/ HSI 150-K2- Varia/ HSI 150-K2- Varia/ Inclusive hex key for fixing the adjusted length (included in scope of delivery) Cable entries HSI 150-GSM VARIA CABLE ENTRY Item Cable entry HSI 150-GSM Varia for pipe-ø 110 mm Cable entry HSI 150-GSM Varia for pipe-ø 125 mm Cable entry HSI 150-GSM Varia for pipe-ø 160 mm Suitable for wallthickness (in mm) Article code Article number Picture HSI 150-GSM110- Varia/ HSI 150-GSM110- Varia/ HSI 150-GSM110- Varia/ HSI 150-GSM110- Varia/ HSI 150-GSM125- Varia/ HSI 150-GSM125- Varia/ HSI 150-GSM125- Varia/ HSI 150-GSM125- Varia/ HSI 150-GSM160- Varia/ HSI 150-GSM160- Varia/ HSI 150-GSM160- Varia/ HSI 150-GSM160- Varia/ ACCESSORY Spacer to enlarge axis-centre distance to 250 mm (order separately) HSI-AH

8 Cable sealing system 150 WALL INSERTS AND PLASTIC FLANGE APPLICATION: Waterproof concrete stress class 1 Wall insert HSI 150-K/X: single-sided connection of systemsealing at the outside of the building minimum wall thickness 70 mm blind cover and blind plate (to be knocked out) guarantee double safety at wall thicknesses mm (in 10 mm steps) available for individual wall thicknesses 150 mm plug-in frame system for block assembly pressure-tight up to 2.5 bar after concreting Wall insert HSI 150-K2/X: connections of system sealing possible on both sides minimum wall thickness 100 mm available for individual wall thicknesses 100 mm plug-in frame system for block assembly, available ex stock closed on both sides with blind system cover special designs for double wall/ element walls available pressure-tight up to 2.5 bar after concreting Wall insert HSI 150-GSM: single-sided connection of system sealing, with integrated plug-in socket to connect smooth cable ducts no additional duct connection material necessary minimum wall thickness for pipe connection 110 and 125 mm diameter: 120 mm minimum wall thickness for pipe connection 160 mm diameter: 180 mm maximum wall thickness: 500 mm pressure-tight up to 0.5 bar depending on the cable duct used frame size 220 x 220 mm 430 mm 210 mm 210 mm mm Example as a 2x5 block for 200 mm wall thickness. Article code: HSI 150-2x5-K2/200 Double wall insert HSI 150 fixed as package into the formwork APPLICATION: non-standing seepage water, waterproof concrete stress class 1 Plastic flange HSI 150-DFK: with integrated spirit level flange made of glass fibre reinforced polyamide high force absorption due to high performance plastic max. stability thanks to reinforcing ribs form-closed surface seal made of EPDM fastening elements inclusive sealing rings against water ingress fastening elements made of stainless steel V4A (AISI 316L) sea water resistant Plastic flange HSI 150-DFK Sectional drawing spacing dimensions 8

9 Cable sealing system 150 WALL INSERTS AND PLASTIC FLANGE HSI 150 WALL INSERTS Single wall insert from wall thickness 70 mm Double wall insert from wall thickness 100 mm HSI 150-K/X X=wallthicknessinmm HSI 150-K2/X X=wallthicknessinmm XXX * XXX * 1 Cable entries Double wall insert for element walls HSI 150-K2-EW/X X=wallthicknessinmm XXX * 1 Single wall insert with integrated plug-in socket Ø 110 mm from wall thickness 120 mm HSI 150-GSM 110/X * 2 X=wallthicknessinmm * 1 Single wall insert with integrated plug-in socket Ø 125 mm from wall thickness 120 mm HSI 150-GSM 125/X * 2 X=wallthicknessinmm * 1 Single wall insert with integrated plug-in socket Ø 160 mm from wall thickness 180 mm combination in packages only possible with spacer HSI 150-GSM 160/X X=wallthicknessinmm * 1 Spacer one set consists of 2 pieces to increase center distances by 40 mm, possibility to combine HSI 150 and HSI 90 in bundles HSI-AH * 1 Please find the article number for the exact wall thickness on standard length: 70 up to 500 mm (gradation in 10 mm) * 2 restrictions regarding number and size of cables may occur Slanted wall inserts (30, 45 und 60 ) and customized solutions according to DIN part 6 available on request. HSI 150 PLASTIC FLANGE Plastic flange inclusive fastenings made of stainless steel V4A (AISI 316L) for concrete walls HSI 150-DFK Cartridge of 290 ml colour: grey elastic sealant to optimize wall surface when used with sealing flange EGO MS

10 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES System cover hot shrink sleeves HSI 150-D1/80, -D3/58 and -D7/33: wide application area easy installation with bayonet catch including centering tape at HSI 150-D1/80 and HSI 150-D3/58 unused opening can be closed off with blind plugs VS32/34 respectively VS 58/60 also available with cold shrink sleeves UV- and ozone resistant resistant to transformer oil Transformer station entry: low-voltage cable sealed with HSI 150-D1/80 Centering tape installed in system cover socket of HSI 150-D3/58 Cross-section of a concrete wall flexible, pressurestable KES-hose stainless steel hose clamp wrench size13 extension pipe concrete wall 3-ribbed seal wall insert clamping nut system cover cable rubber sleeve heat shrink-fit sleeve sliding and O-ring x = wall or masonry thickness 10

11 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES HSI 150 SYSTEM COVER HOT SHRINK SLEEVES Item Area of application cable/pipe diameter Article code Article number Picture System cover, closed - sealing cover System cover with 1 socket inclusive 1 piece heat-shrink sleeve 1 piece centering tape System cover with 3 sockets inclusive 3 pieces heat-shrink sleeves 3 pieces centering tape System cover with 7 sockets inclusive 7 pieces heat-shrink sleeves Blind cover HSI 150-D mm HSI 150-D1/ mm HSI 150-D3/ mm HSI 150-D7/ Cable entries Types with cold shrink sleeves available on request. HSI 150 ACCESSORIES Item Application Article code Article number Picture Sealing plug for system cover HSI 150-D7/33 (available as single unit or packing unit = 10 pcs) Sealing plug for system cover HSI 150-D3/58 (available as single unit or packing unit = 10 pcs) Centering tape set of 3 pieces elastomer strips 30 x 430 mm To seal unused sockets For centering and fixing the cables into the system cover sockets for optimal shrinking VS 32/ VS 58/ HSI-ZB HSI 150 REPLACEMENT -/ REPAIR SHRINK SLEEVES Item for system cover Article code Article number Replacement shrink sleeves for HSI 150 Repair sleeves for HSI 150 HSI 150-D1/80 TM HSI 150-D3/58 TM HSI 150-D7/33 TM HSI 150-D1/80 TMR HSI 150-D3/58 TMR HSI 150-D7/33 TMR

12 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES System cover for new and retrofit installation HSI 150-DG: split seal for new and retrofit installation individual adjustment to the diameter of the laid cables on site inscribed segment rings blind plugs for HSI 150-DG-3/24-54 and HSI 150-DG-6/10-36 included in the delivery transformer oil leak-tightness, tested over 90 days KIWA Institute plastic pressure plates made of polyamide 6.6 with 30 % glass-fibre reinforcement V4A (AISI 316L) stainless steel screws and nuts pressure-tight up to 2.5 bar Low-voltage cables sealed with HSI 150-DG-6/10-36 Various installation stages of HSI 150-DG-3/24-54 Pressure plate cover HSI 150-PA-3/24-54 HSI 150-DG: inscription of diameters on segments 12

13 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES HSI DG SYSTEM COVER FOR NEW AND RETROFIT INSTALLATION Item Area of application cable/pipe OD Article code Article number Picture Split system cover with 1 opening inclusive split adapter ring Split system cover with 1 opening inclusive split adapter ring mm HSI 150-DG-1/ mm HSI 150-DG-1/ Cable entries Split system cover with 3 openings inclusive split adapter ring and 3 pieces blind plugs mm HSI 150-DG-3/ Split system cover with 6 openings inclusive split adapter ring and 6 pieces blind plugs mm HSI 150-DG-6/ Scope of delivery of HSI 150-DG includes: lubricating stick GM, knife, cleaning cloth HSI DG ACCESSORIES Item Application Article code Article number Picture Press plate cover for HSI 150-DG-3/24-54 For protecting the threads against dirt HSI 150-PA-3/ Press plate cover for HSI 150-DG-6/10-36 For protecting the threads against dirt HSI 150-PA-6/ Torque wrench 4-20 Nm ¼ inch 1 adapater for cordless screwdriver, square end, ¼ inch 2 extensions, 150 mm ¼ inch 1 extension 100 mm, ¼ inch 1 wrench socket M6, AF 5, ¼ inch 1 wrench socket, M6, 100 mm with ball head, ¼ inch 1 wrench socket, M8, 50 mm with ball head, ¼ inch Tool for installation of system cover HSI 150-DG HSI 150-DG-W

14 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES SEGMENTO HSI 150-SEGMENTO: particularly flexible and gentle sealing for cables with 5 to 31 mm diameter individual clamping of segments no time-consuming modular design easy and quick installation of segments segments can be combined as necessary integrated torque control system simple reinstallation possible all segment openings closed with blind plugs gas- and watertight up to 0.5 bar when installed on outside of building HSI wall insert with SEGMENTO - sealing of control lines in a substation HSI SEGMENTO with integrated torque control system and bling plugs Sealing of cables for street lighting with SEGMENTO 14

15 Cable sealing system 150 SYSTEM COVERS AND SYSTEM SEALINGS FOR CABLES HSI 150-SEGMENTO System lid as segment receptacle The violet segment application area for 2 cables, diameter mm inclusive 2 blind plugs The yellow segment application area for 3 cables, diameter mm inclusive 3 blind plugs The blue segment application area for 6 cables, diameter mm inclusive 6 blind plugs The orange segment application area for 8 cables, diameter 5-15 mm inclusive 8 blind plugs HSI 150-S SEG 2/ SEG 3/ SEG 6/ SEG 8/ Cable entries COMBINATION KIT SEGMENTO KKS combination kit for pressure-tight outside sealing of core drillings with a diameter of 150 mm consisting of: 1x plastic flange HSI 150-DFK with fastenings, 1x system cover HSI 150-S3, 3x selected segments SEG x/xx, 1x GMS lubricant, 1x installation instructions KKS ordering example: KKS 338 comprise: 1x HSI 150-DFK, 1x HSI 150-S3, 2x SEG 3/26, 1x SEG 8/15, 1x GMS SEGMENTO ACCESSORIES Lubricant SEGMENTO 10 g GMS Cable diameter gauge SEGMENTO to determin the suitable segments according to the cable diameter Torque screwdriver (1,2 Nm) SEGMENTO with acoustic signal BSS DMS

16 Cable sealing system 150 SYSTEM COVERS FOR THE CONNECTION OF CABLE DUCTS Plug-in socket system HSI 150 D (pipe OD) GSM: for smooth pipes / ducts easy and quick installation, no additional connecting components necessary economic solution compact design pressure-tight up to 0.5 bar, depending on the pipe / duct used Sleeve method HSI 150 M (pipe OD): can be used with smooth and corrugated pipes patented clip ring technology for sealing of corrugated pipes (indicate pipe type and pipe manufacturer, please) mechanically stable, elastic connection using special sleeves and tightening straps made from stainless steel V4A (AISI 316L) pressure-tight up to 0.5 bar, depending on the pipe / duct used Cold shrink method HSI 150 D (pipe OD) KS: for corrugated pipes shrink method, no tools necessary stress-free sealing for pressure-sensitive pipes pressure-tight up to 0.5 bar, depending on the pipe / duct used Connection of corrugated pipes with cold shrink method HSI 150-M 168 Connection of corrugated pipes with cold shrink sleeves HSI 150-D 110-KS Connection of rigid cable protection pipe DN 125 with HSI 150-D 125-GSM 16

17 Cable sealing system 150 SYSTEM COVERS FOR THE CONNECTION OF CABLE DUCTS HSI 150 PLUG-IN SOCKET SYSTEM FOR SMOOTH PIPES Item Pipe OD Article code Article number Picture System cover for pipe connection System cover for pipe connection 110 mm HSI 150-D 110-GSM mm HSI 150-D 125-GSM Cable entries System cover for pipe connection 160 mm HSI 150-D 160-GSM HSI 150 RUBBER SLEEVES FOR SMOOTH AND CORRUGATED PIPES Item Pipe OD Article code Article number Picture System cover for smooth pipes System cover for corrugated pipes inclusive clip rings System cover for smooth pipes System cover for corrugated pipes inclusive clip rings System cover for smooth pipes System cover for smooth pipes System cover for corrugated pipes inclusive clip rings 110 mm 125 mm HSI 150-M HSI 150-M 110-WR* for Kabuflex: HSI 150-M HSI 150-M 125-WR* for Kabuflex: mm HSI 150-M mm HSI 150-M HSI 150-M 168-WR* for Kabuflex: * Kindly indicate pipe manufacturer and pipe type in your order. For each pipe connection 2 profile sealing rings are necessary (available from the pipe manufacturer, to be provided on-site). HSI 150 COLD SHRINK SLEEVES FOR CORRUGATED PIPES Item Pipe OD Article code Article number Picture System cover for corrugated pipes System cover for corrugated pipes 110 mm HSI 150-D 110-KS mm HSI 150-D 125-KS HSI 150 REPLACEMENT COLD SHRINK SLEEVES Item For system cover Article code Article number Replacement shrink-fit sleeves for HSI 150 HSI 150-D 110-KS KS HSI 150-D 125-KS KS

18 Cable sealing system 150 CABLE ENTRY SYSTEM APPLICATION: Waterproof concrete stress class 1 Cable entry system KES-M 150: pressure-tight ducting system up to 2.5 bar (outer pressure) for connecting HSI 150-wall inserts high mechanical stability elastic connection with special system sleeves and straps made of stainless steel smooth inner surface for gentle cable feeding sealingofcableswithheatshrinkorcoldshrinksleevesorrubberpressseals adaption with common cable ducts possible also available as role commodity (up to a length of 25 m), extensionpossiblewithconnectionsleevekes-m150htv Cross-section of a concrete wall flexible, pressurestable KES-hose stainless steel hose clamp wrench size13 extension pipe concrete wall 3-ribbed seal wall insert clamping nut system cover cable Pressure-tight connection of Hateflex to HSI 150-wall inserts rubber sleeve heat shrink-fit sleeve sliding and O-ring x = wall or masonry thickness SPIRAL HOSE WITH A SMOOTH INNER SURFACE FOR GENTLE CABLE FEEDING Øi = 150 MM Length (m) Article code Article number Picture 2 Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Hateflex 14150/ Customized lengths available 18

19 Cable sealing system 150 CABLE ENTRY SYSTEM KES-M 150 CABLE ENTRY SYSTEM Connection sleeve for hose extension / connection of Hateflex System cover for pressure-tight connection of spiral hose Hateflex to wall insert HSI 150 Cement-coated wall sleeve (legth 500 mm) with sleeve floor entry for Hateflex spiral hose Connection set for core drill/wall sleeves inclusive 2 press seals for connecting the Hateflex spiral hose to core drills Ø 200 mm. max. wallthickness 500 mm * Sealing set sleeve KES-M 150-WE including interchangeable insert with segmented ring technology for sealing cables at the end of the spiral hose Hateflex 14150: of 1 cable, Ø mm or 3 cables, Ø mm or 6 cables, Ø 8-36 mm (installation before cables are pulled through) inclusive blind plug Sleeve to be used with interchangeable insert WE 160-z/d to seal cables on end of spiral hose Hateflex (installation before cables are pulled through) Split interchangeable insert with segmented ring technology for installation in sleeve KES-M 150-WE for sealing: of 1 cable, Ø mm or 3 cables, Ø mm or 6 cables, Ø 8-36 mm inclusive blind plug Interchangeable insert to be used with sleeve KES-M 150-WE customized according to cables to be installed z= number of cables d= cable diameter * variants available at KES-M 150 HTV KES-M 150-D KES-M150-ZVR 150/ KES-M 150-KB-Set KES-M 150 WE160- SG-1/48-83 KES-M 150 WE160- SG-3/22-54 KES-M 150 WE160- SG-6/ KES-M 150-WE WE 160-SG-1/ WE 160-SG-3/ WE 160-SG-6/ WE 160-z/d e.g. KES-M 150 WE160-SG-6/8-36 e.g. WE 160-SG-3/22-54 Cable entries ACCESSORIES Installation fixture KES-M ZVR-FUBO-Fix C-rack KES-M ZVR-FUBO-FIX (length 1200 mm) with 4 adjustable earth spikes Fastening bow for Ø 160 mm suitable for fixing the KES-M 150-ZVR150/500 to the installation fixture, including fixing elements (max. 4 pieces in a row possible) Befestigungsbogen für KES-M ZVR- FUBO-FIX

20 Cable sealing system 150 CABLE ENTRY SYSTEM KES-M 150 CABLE ENTRY SYSTEMS Connection sleeve for connecting rigid cable ducts OD = 110 mm* to spiral hose Hateflex KES-M 150-M set of clip rings to stabilize the corrugated pipe within the sleeve (kindly indicate pipe manufacturer and pipe type in your order) CR 110 for Kabuflex: Connection sleeve for connecting rigid cable ducts OD = 125 mm* to spiral hose Hateflex KES-M 150-M set of clip rings to stabilize the corrugated pipe within the sleeve (kindly indicate pipe manufacturer and pipe type in your order) CR 125 for Kabuflex: Connection sleeve for connecting rigid cable ducts OD = 160 mm* to spiral hose Hateflex set of clip rings to stabilize the corrugated pipe within the sleeve (kindly indicate pipe manufacturer and pipe type in your order) Rigid pipe section OD = 160 mm with sleeve for connection to spiral hose Hateflex (tight wall sealing in core drillings when used together with HRD press seals). Spacer 2x3 for positioning of hose packages with Hateflex KES-M 150-M CR 160 for Kabuflex: KES-M 150-R KES 150-2x3 KA * additional clip rings CR are necessary to connect corrugated pipes For each pipe connection 2 profile sealing rings are necessary (available from the pipe manufacturer, to be provided on-site). HSI 150 / KES 150 TOOL AND ASSEMBLY SET Tool set for pressure-tight strap assembly, consisting of 1 torque 4-20 Nm, ¼ inch, 1 extension 150 mm, ¼ inch, 1 socket for hexagon spanner SW 13, ¼ inch 1 socket for hexagon spanner SW 8, ¼ inch Torque wrench 4-20 Nm ¼ inch 1 adapater for cordless screwdriver, square end, ¼ inch 2 extensions, 150 mm ¼ inch 1 extension 100 mm, ¼ inch 1 wrench socket M6, AF 5, ¼ inch 1 wrench socket, M6, 100 mm with ball head, ¼ inch 1 wrench socket, M8, 50 mm with ball head, ¼ inch KES-M-W HSI 150-DG-W

21 Cable sealing system 150 ACCESSORIES HSI 150 ACCESSORIES Flexible pin spanner Flexible pin spanner (buildings with perimeter insulation up to 100 mm) Sealing plug for system cover HSI 150-D7/33 (available as single unit or packing unit = 10 pcs) SLS 6G SLS 6GD VS 32/ Cable entries Sealing plug for system cover HSI 150-D3/58 (available as single unit or packing unit = 10 pcs) VS 58/ Centering tape set, consisting of 3 pieces elastomer strips 30 x 430 mm. For centering and fixing the cables into the system cover sockets for optimal shrinking. HSI-ZB finger sleeve for system cover HSI 150-D7/33 3-finger sleeve for system cover HSI 150-D3/58 4-finger sleeve for system cover HSI 150-D7/33 4-finger sleeve for system cover HSI 150-D3/58 AK.3F ,2 AK.3F AK.4F AK.4F Lubricant 200 g GML Hot-melt tape, cold welding, length 3 m, width approx. 35 mm Hatetherm Scapa Cable cleaner, content: 1000 ml, quick and residue-free evaporation KR M.T.X Cartridge of 290 ml colour: grey elastic sealant to optimize wall surface when used with sealing flange EGO MS Torque srewdriver (1,2 Nm) SEGMENTO with acoustic signal DMS

22 Cable sealing system 90 WALL INSERTS AND ALUMINIUM FLANGE APPLICATION: Waterproof concrete stress class 1 Wall insert HSI 90-K/X: single-sided connection to system sealing possible minimum wall thickness 70 mm available in individual thicknesses 70 mm plug-in frame system for block assembly on-site pressure-tight cover pressure-tight up to 2 bar after concreting Wall insert HSI 90-K2/X: connections to system sealing possible on both sides minimum wall thickness 100 mm available in individual wall thicknesses 100 mm plug-in frame system for block assembly, available ex stock pressure-tight cover on both sides pressure-tight up to 2 bar after concreting 135 mm 135 mm frame size 145 x 145 mm 685 mm 280 mm Example as a 2x5 block for 200 mm wall thickness: Article code: HSI 90-2x5-K2/200 Double wall insert HSI 90 fixed as package into the formwork APPLICATION: non-standing seepage water, waterproof concrete stress class 1 Aluminium flange HSI 90-DF: Aluminium flange HSI 90-DF mm Sectional drawing spacing dimensions 46 46mm connection to system sealing possible aluminium flange with KTL (cataphoretic) - coating (optimum protection against corrosion) for retrofit installation core drilling max. 90 mm diameter installation on container walls possible including chloroprene (CR) surface seal, 10 mm thick and fastenings made of stainless steel V4A (AISI 316L) for concrete walls mm Kernbohrung max.90 mm core drilling max. 90 mm diameter min. 185 mm 10 mm mm 22

23 Cable sealing system 90 WALL INSERTS AND ALUMINIUM FLANGE HSI 90 WALL INSERTS Single wall insert from wall thickness 70 mm HSI 90-K/X X=wallthicknessinmm * Cable entries Double wall insert from wall thickness 100 mm HSI 90-K2/X X=wallthicknessinmm * * Please find the article number for the exact wall thickness on HSI 90 ALUMINIUM FLANGE Aluminium flange inclusive fastenings made of stainless steel V4A (AISI 316L) for stainless steel HSI 90-DF Cartridge of 290 ml colour: grey elastic sealant to optimize wall surface when used with sealing flange EGO MS

24 Cable sealing system 90 SYSTEM COVERS FOR CABLES System cover hot shrink sleeves HSI 90-D1/75, -D3/32 and -D6/20: wide application area easy installation with bayonet catch including centering tape at HSI 90-D1/75 unused opening can be closed off with blind plugs VS 20, VS 32/34 respectively also available in cold shrink sleeves UV- and ozone resistant resistant to transformer oil Transformer station entry: low-voltage cable sealed with HSI 90-D1/75 and HSI 90-D3/32 Cross-section of a concrete wall flexible, pressurestable KES-hose stainless steel hose clamp wrench size13 extension pipe concrete wall 3-ribbed seal wall insert clamping nut system cover cable rubber sleeve heat shrink-fit sleeve sliding and O-ring x = wall or masonry thickness 24

25 Cable sealing system 90 SYSTEM COVERS FOR CABLES HSI 90 SYSTEM COVER HOT SHRINK SLEEVES Item Area of application cable/pipe diameter Article code Article number Picture System cover, closed - sealing cover System cover with 1 socket inclusive 1 piece heat-shrink sleeve 1 piece centering tape System cover with 3 sockets inclusive 3 pieces heat-shrink sleeves Blind cover HSI 90-D mm HSI 90-D1/ mm HSI 90-D3/ Cable entries System cover with 6 sockets inclusive 6 pieces heat-shrink sleeves 8 18 mm HSI 90-D6/ Types with cold shrink sleeves available on request. HSI 90 ACCESSORIES Item Application Article code Article number Picture Sealing plug for system cover HSI 90-D6/20 (available as single unit or packing unit = 10 pcs) Sealing plug for system cover HSI 90-D3/32 (available as single unit or packing unit = 10 pcs) To seal unused sockets VS 20 VS 32/ Centering tape set, consisting of 3 pieces elastomer strips 30 x 430 mm For centering and fixing the cables into the system cover sockets for optimal shrinking HSI-ZB HSI 90 REPLACEMENT -/ REPAIR HOT SHRINK SLEEVES Item for system cover Article code Article number Replacement heat shrink sleeves for HSI 90 Repair sleeves for HSI 90 HSI 90-D1/75 TM HSI 90-D3/32 TM HSI 90-D6/20 TM HSI 90-D1/75 TMR HSI 90-D3/32 TMR HSI 90-D6/20 TMR

26 Cable sealing system 90 SYSTEM COVERS FOR THE CONNECTION OF CABLE DUCTS APPLICATION: Waterproof concrete stress class 1 Sleeve method HSI 90 M (pipe OD): can be used with smooth and corrugated pipes patented clip ring technology for sealing of corrugated pipes (indicate pipe type and pipe manufacturer, please) mechanically stable, elastic connection using special sleeves and tightening straps made from stainless steel V4A (AISI 316L) pressure-tight up to 0.5 bar, depending on the pipe / duct used Cold shrink method HSI 90 D/75-KS: for corrugated pipes shrink-fit method, no tools necessary stress-free sealing for pressure-sensitive pipes pressure-tight up to 0.5 bar, depending on the pipe / duct used Assembly of double wall insert HSI 90-K2 before concreting HSI 90-K2 after concreting: empty ducts will be installed subsequently Connection of corrugated pipes HSI 90-D75 KS 26

27 Cable sealing system 90 SYSTEM COVERS FOR THE CONNECTION OF CABLE DUCTS HSI 90 SLEEVE METHOD FOR SMOOTH AND CORRUGATED PIPES Item Pipe outer diameter Article code Article number Picture System cover for smooth pipes System cover for smooth pipes System cover for corrugated pipes inclusive clip rings System cover for smooth pipes System cover for corrugated pipes inclusive clip rings 75 mm HSI 90-M mm 110 mm * Kindly indicate pipe manufacturer and pipe type in your order. HSI 90-M 90 HSI 90-M 90-WR* HSI 90-M 110 HSI 90-M 110-WR* for Kabuflex: for Kabuflex: Cable entries HSI 90 COLD SHRINK SLEEVES FOR CORRUGATED PIPES Item Pipe outer diameter Article code Article number Picture System cover for corrugated pipes 75 mm HSI 90-D 75-KS HSI 90 REPLACEMENT COLD SHRINK SLEEVES Item For system cover Article code Article number Replacement cold shrink sleeves for HSI 90 HSI 90-D 75-KS KS

28 Cable sealing system 90 CABLE ENTRY SYSTEM APPLICATION: Waterproof concrete stress class 1 Cable entry system KES-M 90: pressure-tight ducting system up to 2.5 bar (outer pressure) for connection to the HSI 90-wall inserts high mechanical stability elastic connection with special system sleeves and straps made of stainless steel smooth inner surface for gentle cable feeding sealingofcableswithheatshrinkorcoldshrinksleevesorrubberpressseals adaptation with common cable ducts possible also available as role commodity (up to a length of 25 m), extension possible withconnectionsleevekes-m90htv flexible, pressurestable KES-hose stainless steel hose clamp wrench size13 Cross-section of a concrete wall extension pipe concrete wall 3-ribbed seal wall insert clamping nut system cover cable KES-M 90-D Connection to the HSI 90 wall insert rubber sleeve heat shrink-fit sleeve sliding and O-ring x = wall or masonry thickness SPIRAL HOSE WITH A SMOOTH INNER SURFACE FOR GENTLE CABLE FEEDING Øi = 90 MM Customized lengths available Length (m) Article code Article number Picture 1,5 Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/ Hateflex 14090/

29 Cable sealing system 90 CABLE ENTRY SYSTEM KES-M 90 CABLE ENTRY SYSTEMS Connection sleeve for hose extension / connection of Hateflex System cover for pressure-tight connection of spiral hose Hateflex to HSI 90 wall insert Cement-coated wall sleeve (length 500 mm) with sleeve floor entry for Hateflex spiral hose KES-M 90 HTV KES-M 90-D KES-M90-ZVR 100/ Cable entries Connection set for core drill/wall sleeves inclusive 2 press seals for connecting the Hateflex spiral hose to core drills Ø 150 mm max. wall thickness 500 mm Sealing set sleeve KES-M 90-WE WE including interchangeable insert WE 100 with segmented ring technology for sealing cables at the end of the spiral hose Hateflex for: 1 cable, Ø mm inclusive blind plug KES-M 90-KB-Set KES-M 90-WE100- SG-1/ Sleeve to be used with interchangeable insert WE 100-z/d to seal cables to end of spiral hose Hateflex (installation before cables are pulled through) Split interchangeable insert with segmented ring technology for installation in sleeve KES-M 90-WE for sealing 1 = number of cables = cable Ø inclusive blind plug Interchangeable insert to be used with sleeve KES-M 90-WE customized according to cables to be installed z= number of cables d= cable diameter KES-M 90-WE WE100-SG-1/ WE 100-z/d ACCESSORIES Installation fixture KES-M ZVR-FUBO-Fix C-rack (length 1200 mm) with adjustable earth spikes KES-M ZVR-FUBO-FIX Fastening bow for Ø 110 mm suitable for fixing the KES-M90-ZVR100/500 to the installation fixture, including fixing elements (max. 5 pieces in a row possible) Befestigungsbogen für KES-M ZVR- FUBO-FIX

30 Cable sealing system 90 CABLE ENTRY SYSTEM KES-M 90 CABLE ENTRY SYSTEMS Connection sleeve for connecting rigid cable ducts OD = 90 mm* to spiral hose Hateflex KES-M 90-M set of clip rings to stabilize the corrugated pipe within the sleeve (kindly indicate pipe manufacturer and pipe type in your order) CR 90 for Kabuflex: Connection sleeve for connecting rigid cable ducts OD = 110 mm* to spiral hose Hateflex KES-M 90-M set of clip rings to stabilize the corrugated pipe within the sleeve (kindly indicate pipe manufacturer and pipe type in your order) CR 110 for Kabuflex: Rigid pipe section OD = 90 mm with sleeve for connection to spiral hose Hateflex (tight wall sealing in core drillings when used together with HRD press seals). KES-M 90-R Spacer 2x4 for positioning of hose packages with Hateflex KES 90-2x4 KA * additional clip rings CR are necessary to connect corrugated pipes For each pipe connection 2 profile sealing rings are necessary (available from the pipe manufacturer, to be provided on-site). HSI 90/KES 90 TOOL SET Tool set for pressure-tight strap assembly, consisting of 1 torque 4-20 Nm, ¼ inch, 1 extension 150 mm, ¼ inch, 1 socket for hexagon spanner SW 13, ¼ inch 1 socket for hexagon spanner SW 8, ¼ inch KES-M-W

31 Cable sealing system 90 ACCESSORIES HSI 90 ACCESSORIES Flexible pin spanner Flexible pin spanner (buildings with perimeter insulation up to 100 mm) Sealing plug for system cover HSI 90-D6/20 (available as single unit or packing unit = 10 pcs) SLS 6G SLS 6GD VS Cable entries Sealing plug for system cover HSI 90-D3/32 (available as single unit or packing unit = 10 pcs) VS 32/ Centering tape set, consisting of 3 pieces elastomer strips 30 x 430 mm HSI-ZB 3er Set finger sleeve for HSI 90-D3/32 AK.3F , finger sleeve for HSI 90-D3/32 AK.4F Lubricant 200 g GML Hot-melt tape, cold welding, length 3 m, width approx. 35 mm Hatetherm Scapa Cable cleaner, content: 1000 ml, quick and residue-free evaporation KR M.T.X Cartridge of 290 ml colour: grey elastic sealant to optimize wall surface when used with sealing flange EGO MS

32 Press seals for cables STANDARD PRESS SEAL HRK-SSG AND HRD SG UNIVERSAL SEAL FOR CABLES WITH SEGMENT RING TECHNOLOGY APPLICATION: standing seepage water, pressing water, waterproof concrete stress class 1 Standard press seal for cables HRK SSG: absolutely gas- and watertight sealing width 40 mm splitsealingforretrofitinstallation supersegmentedringtechnology-individualadjustmenttothecablediameteron-site segments with exact diameter indication form-fittingconnectionsofthepressplates EPDM rubber V4A (AISI 316L) stainless steel screws and nuts plasticpressureplatesmadeofglassfibrereinforcedpolyamide highly robust plastic pressure plates with reinforcement ribs Pressure plates with form-fitting connection Segments with exact diameter indication APPLICATION: standing seepage water, pressing water, waterproof concrete stress class 1 Standard press seal for cables HRD SG: absolutely gas- and watertight sealing width 40 mm splitsealingforretrofitinstallation segmentringtechnology individualadjustingtoinstalledcablediameterson-site EPDM rubber pressure plates made of stainless steel V2A (AISI 304L) sturdy 5 mm pressure plates HRD 150-SG installed in fibre cement wall sleeves HRD 150-SG-6/8-35 individual adjusting to diameters of cables 32

33 Press seals for cables STANDARD PRESS SEAL HRK-SSG AND HRD SG UNIVERSAL SEAL FOR CABLES WITH SEGMENT RING TECHNOLOGY HRK SSG STANDARD PRESS SEAL FOR CABLES WITH SUPER SEGMENTED RING TECHNOLOGY Core drilling/ wall sleeve ID 100 (available as single unit or packing unit = 9 pcs) Number of cables Cable diameter Article code Article number Picture mm HRK 100-SSG-1/ mm HRK 100-SSG-4/ (available as single unit or packing unit = 8 pcs) mm HRK 150-SSG-1/36-70 * mm HRK 150-SSG-1/ * mm HRK 150-SSG-3/ mm HRK 150-SSG-6/ e.g. HRK 150-SSG-3/ (available as single unit or packing unit = 8 pcs) * without plugs mm HRK 200-SSG-1/ * mm HRK 200-SSG-3/ Press seals HRD SG STANDARD PRESS SEAL FOR CABLES Core drilling/ wall sleeve ID Number of cables Cable diameter Article code Article number Picture mm HRD 80-SG-1/ ,5 mm HRD 100-SG-8/4-16, HRD 100-SG-2/8-30-3/4-16, of which mm of which ,5 mm mm HRD 104-SG-1/ mm HRD 104-SG-4/ ,5 mm HRD 104-SG-8/4-16, mm HRD 125-SG-3/ mm HRD 125-SG-6/ ,5 mm HRD 125-SG-10/4-16, mm HRD 150-SG-9/ HRD 150-SG-4/8-30-6/4-16, of which mm of which ,5 mm 7 HRD 200-SG-3/6-54-4/ of which mm 200 of which mm 15 HRD 200-SG-7/ /3,5-16, of which mm of which 8 3,5 16,5 mm e.g. HRD 200-SG-3/6-54-4/

34 Press seals for cables INDIVIDUAL PRESS SEAL WITH INTEGRATED TEST VALVE HRD PV APPLICATION: standing seepage water, pressing water, waterproof concrete stress class 1 Individual press seal HRD-PV: absolutely gas- and watertight sealing width 2 x 30 mm closed or split different outer diameters can be manufactured exactly to customers requirements easy to mount optionally available with overlapping flange (F) or eccentric simple monitoring/control tests possible with integrated test valve short delivery times for core drillings/wall sleeves from Ø mm EPDM, NBR, KTW or silicone rubber suitable for sealing rigid cable ducts pressure plates made from stainless steel V2A (AISI 304L), optionally V4A (AISI 316L) sturdy 5 mm pressure plates HRD 150-PVG in core drilling HRD 150-PVG in core drilling CONFIGURATION TABLE Number = Z cables/pipes Core drilling diameter HRD 80 Core drilling diameter HRD 100 Core drilling diameter HRD 125 Core drilling diameter HRD 150 Core drilling diameter HRD 200 Core drilling diameter HRD 250 Core drilling diameter HRD 300 Cable/pipe diameter = d max

35 Press seals for cables INDIVIDUAL PRESS SEAL WITH INTEGRATED TEST VALVE HRD PV INDIVIDUAL PRESS SEAL HRD-PV CLOSED Core drilling/ wall sleeve ID Optimal application range diameter for 1 cable Closed design Article code Article number Picture 80 mm 0 30 mm HRD 80-PV-1/d V2A/EPDM mm 0 50 mm HRD 100-PV-1/d V2A/EPDM mm 0 75 mm HRD 125-PV-1/d V2A/EPDM mm mm HRD 150-PV-1/d V2A/EPDM mm mm HRD 200-PV-1/d V2A/EPDM mm mm HRD 250-PV-1/d V2A/EPDM mm mm HRD 300-PV-1/d V2A/EPDM Customized diameters available * For maximum cable configuration please refer to table on page 34. d = cable diameter e.g. HRD 150-PV-1/50 INDIVIDUAL PRESS SEAL HRD-PV SPLIT Core drilling/ wall sleeve ID Optimal application range diameter for 1 cable Split design Article code Article number Picture Press seals 80 mm 0 30 mm HRD 80-PVG-1/d V2A/EPDM mm 0 50 mm HRD 100-PVG-1/d V2A/EPDM mm 0 75 mm HRD 125-PVG-1/d V2A/EPDM mm mm HRD 150-PVG-1/d V2A/EPDM mm mm HRD 200-PVG-1/d V2A/EPDM mm mm HRD 250-PVG-1/d V2A/EPDM mm mm HRD 300-PVG-1/d V2A/EPDM Customized diameters available * For maximum cable configuration please refer to table on page 34. d = cable diameter e.g. HRD 150-PVG-1/50 Further variants: blind insert, article code: e.g. HRD 117-PV-0 split, eccentric sealing insert, article code: e.g. HRD 156-PVG-1/45-ex-23 All individual press seal-variants also available with overlapping flange. ACCESSORIES Test pump with digital pressure gauge DIGIT PPM

36 Press seals for cables INDIVIDUAL PRESS SEAL (CLOSED AND SPLIT), SEALING WIDTH 30 MM APPLICATION: standing seepage water, pressing water, waterproof concrete stress class 1 Individual press seal HRD: absolutely gas- and watertight sealing width 30 mm closed or split different outer diameters can be manufactured exactly to customers requirements easy to mount optionally available with overlapping flange (F) or eccentric suitable for one or more cables for core drillings/wall sleeves from diameter 25 mm suitable for sealing rigid cable ducts EPDM, NBR or silicone rubber pressure plates made from stainless steel V2A (AISI 304L), optionally V4A (AISI 316L) sturdy 5 mm pressure plates HRD 150-1G sealing several cables per core drilling / wall sleeve HRD 200-1G installed in a steel pipe CONFIGURATION TABLE Number = Z cables/pipes Core drilling diameter HRD 50 Core drilling diameter HRD 80 Core drilling diameter HRD 100 Core drilling diameter HRD 125 Core drilling diameter HRD 150 Core drilling diameter HRD 200 Core drilling diameter HRD 250 Cable/pipe diameter = d max Further sizes up to diameter 1,500 mm available on short notice upon request. 36

37 Press seals for cables INDIVIDUAL PRESS SEAL (CLOSED AND SPLIT), SEALING WIDTH 30 MM, EPDM WITH V2A (AISI 304L) INDIVIDUAL PRESS SEAL CLOSED Core drilling/ wall sleeve ID Optimal application range diameter Closed design Article code Article number 50 mm 0 25 mm HRD /d mm 0 32 mm HRD /d mm 0 40 mm HRD /d mm 0 50 mm HRD /d mm 0 63 mm HRD /d mm mm HRD /d mm mm HRD /d mm mm HRD /d mm mm HRD /d Customized diameters available * For maximum cable configuration please refer to table on page 36 INDIVIDUAL PRESS SEAL SPLIT Core drilling/ wall sleeve ID Optimal application range diameter d = cable diameter Split design Article code Article number 50 mm 0 25 mm HRD 50-1G-1/d mm 0 32 mm HRD 60-1G-1/d mm 0 40 mm HRD 70-1G-1/d mm 0 50 mm HRD 80-1G-1/d mm 0 63 mm HRD 100-1G-1/d mm mm HRD 125-1G-1/d mm mm HRD 150-1G-1/d mm mm HRD 200-1G-1/d mm mm HRD 250-1G-1/d Picture Picture Press seals Customized diameters available * For maximum cable configuration please refer to table on page 36 d = cable diameter Further variants: blind insert, article code: e.g. HRD split, eccentric sealing insert, article code: e.g. HRD 156-1G-1/45-ex-23 All individual press seal-variants also available with overlapping flange. 37

38 Press seals for cables INDIVIDUAL PRESS SEAL (CLOSED AND SPLIT), SEALING WIDTH 60 MM APPLICATION: standing seepage water, pressing water, high stress (chemical, thermal), difficult installation conditions, waterproof concrete stress class 1 Individual press seal HRD: absolutely gas- and watertight sealing width 60 mm closed or split different outer diameters can be manufactured exactly to customers requirements easy to mount optionally available with overlapping flange (F) or eccentric suitable for one or more cables for core drillings/wall sleeves from diameter 25 mm EPDM, NBR or silicone rubber pressure plates made from stainless steel V2A (AISI 304L), optionally V4A (AISI 316L) sturdy 5 mm pressure plates HRD blind insert HRD 150-2G-2/18-2/27 CONFIGURATION TABLE Number = Z Cables/pipes Core drilling diameter HRD 50 Core drilling diameter HRD 80 Core drilling diameter HRD 100 Core drilling diameter HRD 125 Core drilling diameter HRD 150 Core drilling diameter HRD 200 Core drilling diameter HRD 250 Cable/pipe diameter = d max Further diameters up to 1,500 mm available on short notice upon request. 38

39 Press seals for cables INDIVIDUAL PRESS SEAL (CLOSED AND SPLIT), SEALING WIDTH 60 MM, EPDM WITH V2A (AISI 304L) INDIVIDUAL PRESS SEAL CLOSED Core drilling/ wall sleeve ID INDIVIDUAL PRESS SEAL SPLIT Core drilling/ wall sleeve ID Optimal application range diameter Optimal application range diameter Closed design Article code Split design Article code Article number 50 mm 0 25 mm HRD /d mm 0 32 mm HRD /d mm 0 40 mm HRD /d mm 0 50 mm HRD /d mm 0 63 mm HRD /d mm mm HRD /d mm mm HRD /d mm mm HRD /d mm mm HRD /d Customized diameters available * For maximum cable configuration please refer to table on page 36. d = cable diameter Article number 50 mm 0 25 mm HRD 50-2G-1/d mm 0 32 mm HRD 60-2G-1/d mm 0 40 mm HRD 70-2G-1/d mm 0 50 mm HRD 80-2G-1/d mm 0 63 mm HRD 100-2G-1/d mm mm HRD 125-2G-1/d mm mm HRD 150-2G-1/d mm mm HRD 200-2G-1/d mm mm HRD 250-2G-1/d Picture Picture Press seals Customized diameters available * For maximum cable configuration please refer to table on page 36. d = cable diameter Further variants: blind insert, article code: e.g. HRD split, eccentric sealing insert, article code: e.g. HRD 137-2G-1/39-ex-20 All individual press seal-variants also available with overlapping flange. 39

40 Wall sleeves SFR RENOVATION WALL SLEEVE APPLICATION: non-standing seepage water Renovation wall sleeve SFR: for subsequent installation in wall break-throughs, core drillings or rectangular openings breaking resistant, dimensionally stable can easily be shortened to required length suitable for all wall types except for waterproof concrete roughened surface will homogeneously connect to mortar compact design allows for smallest possible drillings / break throughs dimensions: SFR 100: ID = 100 mm, OD = 110 mm SFR 150: ID = 150 mm, OD = 162 mm SFR 200: ID = 200 mm, OD = 214 mm plastic-modified, bitumin thick coating with rounded groove interior diam. wall thickness 4,5 u. 6 mm min. 20 mm mortar all around Roughened surface SFR - installation according to DIN 18195, part 4 40

41 Wall sleeves SFR RENOVATION WALL SLEEVE SFR RENOVATION WALL SLEEVE Medium pipe Wall sleeve ID Wall sleeve OD Optimum application range OD Maximum poss. area of application OD* Minimum drilling Length Article code Article number Picture 100 mm 110 mm 0 63 mm 0 76 mm 150 mm 300 mm SFR 100/ mm 110 mm 0 63 mm 0 76 mm 150 mm 500 mm SFR 100/ mm 110 mm 0 63 mm 0 76 mm 150 mm 1000 mm SFR 100/ mm 162 mm mm mm 200 mm 300 mm SFR 150/ SFR 100/ mm 162 mm mm mm 200 mm 500 mm SFR 150/ mm 162 mm mm mm 200 mm 1000 mm SFR 150/ mm 214 mm mm mm 250 mm 300 mm SFR 200/ mm 214 mm mm mm 250 mm 500 mm SFR 200/ mm 214 mm mm mm 250 mm 1000 mm SFR 200/ Press seals * For maximum cable configuration please refer to table on page 36. Other wall thicknesses on request For more wall sleeves, please also refer to our catalogue.pipe entries 41

42 Wall sleeves SPECIAL SOLUTIONS BEFORE AFTER Existing rectangular opening has to be subsequently sealed Rectangular split flange for several cable penetrations Slanted core drilling in porous wall Fixed/loose flange with slanted empty hose connection and surface sealing Entry of high-voltage cables and cable ducts have to be subsequently sealed in a shaft wall Split fixed/loose flange according to DIN

43 Wall sleeves SPECIAL SOLUTIONS Split multiple HRD flange HRD (2xD)-FG Fixed and loose flange HRD (D)-FUFA for sealing according to DIN part 6 Press seals Split individual press seal HRD-SGi with segmented ring technology Individual press seal HRD 150/160-2SGi with segmented ring technology Slanted double wall insert HSI 150-1x3-K2 S45 /X Double wall insert HSI 150-K2F/X for sealing according to DIN part 6 You can find further special solutions on our website 43

44 Earthings ENTRIES APPLICATION: Waterproof concrete stress class 1 Entry for earthing in concrete HEA / HEA-E: 10 mm conductor core Ø 25 mm with a threaded connection on both sides M12, made of stainless steel V4A (AISI 316L), HEA-E also available with connecting thread M16 pressure-tight water barrier (profiled rubber flange, NBR) contact plates Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holes HEA wall thickness mm HEA-E wall thickness > 200 mm conductor core for HEA-E connection via M16 bolts, galvanised no twisting after installation in concrete according to DIN 18014, DIN EN VDE (with lightning protection) protective Schalungsscheibe cover Ø 72 mm Ø 25 mm Wassersperre water barrier Gewinde thread M12 APPLICATION: Waterproof concrete stress class 1 Insulated entry for substation construction HEA-IS-M12: water Wassersperre barrier protective Schutzabdeckung cover conductor core Ø 25 mm with a threaded connection on both sides M12, made of stainless steel V2A (AISI 304L) pressure-tight water barrier (profiled rubber flange, EPDM) contact plates Ø 72 mm made of stainless steel V2A (AISI 304L) with protective cover minimum wall thickness HEA-IS: 70 mm according to VDE 0101, EN short-circuit tested Ø 72 mm Ø 25 mm min. mind. wall Wandstärke thickness mm mm thread Gewinde M12 M12 APPLICATION: Waterproof concrete stress class 1 Earthing connection and entry HEA-PK-M12 / HEA-PK-M16: conductor core Ø 25 mm with a threaded connection on both sides M12/M16, made of stainless steel V4A (AISI 316L) terminal lug with cross clamp 70 x 70 mm made of steel St37, galvanised pressure-tight water barrier (profiled rubber flange, NBR) contact plates Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holes minimum wall thickness 200 mm conductor core connection with M16 threaded bolts, galvanised according to DIN 18014, DIN EN VDE (with lightning protection) water Wassersperre barrier thread Gewinde M12 or oder M16 M16 Ø 72 mm Ø 25 mm cross-clamp for connecting strip Kreuzklemme irons zum Anschluss up to 40 von x Bandeisen 4 mm 40 x 4 mm rod Rd /12 mm mm min. mind. wall Wandstärke thickness mm mm contact Schalungsscheibe plate thread Gewinde M12 M12 or oder M16 44

45 Earthings ENTRIES HEA / HEA-E ENTRY FOR EARTHING IN CONCRETE Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 12 on both sides, with water barrier and protective foils, for wall thickness 70 mm Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 12 on both sides, with water barrier and protective covers, for wall thickness 100 mm Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 12 on both sides, with water barrier and protective covers, for wall thickness 150 mm Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 12 on both sides, with water barrier and protective covers, for wall thickness 200 mm HEA-M12/ HEA-M12/ HEA-M12/ HEA-M12/ e.g. HEA-M12/100 Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 12 on both sides, with water barrier and protective covers, available for wall thicknesses mm Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M 16 on both sides, with water barrier and protective covers, available for wall thicknesses mm Increments of 10 mm possible HEA-E-M12/X HEA-E-M16/X X=wallthicknessinmm e.g. HEA-E-M12/240 HEA-IS-M12 INSULATED FEEDTHROUGH FOR STATION EARTHING Feedthrough for earthing connections made of stainless steel V2A (AISI 304L), connection M12 on both sides, with water barrier and protective cover (HEA-IS-M12) for wall thickness 100 mm HEA-IS-M12/ Feedthrough for earthing connections made of stainless steel V2A (AISI 304L), connection M12 on both sides, with water barrier and protective cover (HEA-IS-M12) for wall thickness 150 mm HEA-IS-M12/ Feedthrough for earthing connections made of stainless steel V2A (AISI 304L), connection M12 on both sides, with water barrier and protective cover (HEA-IS-M12) for wall thickness 200 mm HEA-IS-M12/ HEA-IS-M12/100 Extra Feedthrough for earthing connections made of stainless steel V2A (AISI 304L), connection M12 on both sides, with water barrier and protective cover (HEA-IS-M12) for wall thickness 250 mm HEA-IS-M12/ Increments of 10 mm possible HEA-PK-M12 EARTHING CONNECTION AND ENTRY Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M12 on both sides, with terminal lug and cross clamp, available for wall thicknesses mm, with water barrier and protective covers Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M16 on both sides, with terminal lug and cross clamp, available for wall thicknesses mm, with water barrier and protective covers Increments of 10 mm possible Short circuit-proof up to 10 KA/1s (VDE 0101/E DIN EN 50522) HEA-PK-M12/X HEA-PK-M16/X X=wallthicknessinmm 45

46 Earthings FIXED POINTS APPLICATION: Waterproof concrete stress class 1 Fixed point with cross clamb HEA-P-M12 / HEA-P-M16: conductor core, Ø 25 mm with threaded connection M12 /M16 made of stainless steel V4A (AISI 316L) cross clamp 70 x 70 mm with threaded bolt M12 or M16 galvanised contact plate Ø 72 mm made of stainless steel V4A (AISI 316L) protective cover made of PE with four nail holes minimum wall thickness 200 mm distance between formwork and earth connection approximately 120 mm according to DIN 18014, DIN EN VDE (with lightning protection) Schalungsscheibe contact plate Ø 72 mm Ø 25 mm Gewinde thread M12 M12 oder or M16 M16 min. mind. wall Wandstärke thickness 200 mm mm cross-clamp Kreuzklemme for connecting zum Anschluss strip irons von Bandeisen up to 40 bis x 40 4 mm x 4 mm rod Rd /12 mm APPLICATION: Waterproof concrete stress class 1 Fixed point with weld groove HEA-A-M12: conductor core, Ø 25 mm with threaded connection M12 made of stainless steel V2A (AISI 304L) fixed point with welded groove made of steel St37 to connect with mm round steel contact plate Ø 72 mm made of stainless steel V2A (AISI 304L) protective foil green transparent distance between formwork and the core iron 50 mm (HEA-A-M12/50) or 70 mm (HEA-A-M12/70) short-circuit tested according to VDE 0101, EN Ø 72 mm Ø 72 mm Ø 25 mm Ø 25 mm Gewinde M12 Gewinde thread M12 Schweißnut weld Schweißnut groove Abstand zur Armierung distance Abstand to zur reinforcement Armierung mind. Wandstärke 50 mm 100 mm abhängig von der min. mind. Beton-Expositionsklasse wall Wandstärke thickness mm mm depending abhängig on von exposure der Beton-Expositionsklasse class of concrete APPLICATION: Waterproof concrete stress class 1 Fixed point with welded or clamped connection HEA-S-M12 / HEA-S-M16: conductor core, Ø 25 mm with threaded connection M12/M16 made of stainless steel V4A (AISI 316L) steel rod Ø 12 mm made of steel St37 for welded or clamped connection in concrete contact plate Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holes according to DIN 18014, DIN EN VDE (with lightning protection) Schalungsscheibe contact plate Ø 72 mm Ø 25 mm Gewinde thread M12 M12 cross-clamp for Kreuzklemme zum connecting Anschluss strip von irons Bandeisen up to bis 40 x 405 x mm 5 mm Rd. rod 8/ mm mm nicht im Lieferumfang not included enthalten 46

47 Earthings FIXED POINTS HEA-P-M12 / HEA-P-M16 FIXED POINT WITH CROSS CLAMP Fixed point with screwed-on crossclamp for the connection in concrete, connection M12, made of stainless steel V4A (AISI 316L), with protective cover, installation length = 120 mm HEA-P-M Fixed point with screwed-on crossclamp for the connection in concrete, connection M16, made of stainless steel V4A (AISI 316L), with protective cover, installation length = 120 mm HEA-P-M HEA-P-M12 HEA-A-M12 FIXED POINT WITH WELD GROOVE Fixed point made of stainless steel V2A (AISI 304L) with weld groove made of steel St37, conductor core Ø 25 mm, connection M12, for distances between formwork and the core iron 50 mm Fixed point made of stainless steel V2A (AISI 304L) with weld groove made of steel St37, conductor core Ø 25 mm, connection M12, for distances between formwork and the core iron 70 mm HEA-A-M12/ HEA-A-M12/ HEA-A-M12/50 HEA-A-M12/70 Extra FIXED POINT WITH WELDED OR CLAMPED CONNECTION Fixed point made of stainless steel V4A (AISI 316L) with screwed-on steel rod made of steel St37, Ø 12 mm, connection M12, for welded or clamped connection in concrete HEA-S-M Fixed point made of stainless steel V4A (AISI 316L) with screwed-on steel rod made of steel St37, Ø 12 mm, connection M16, for welded or clamped connection in concrete HEA-S-M HEA-S-M12 47

48 Earthings ENTRIES APPLICATION: Waterproof concrete stress class 1 Entry for subsequent installation HEA-N: Abdichtung sealing M16 threaded rod made of stainless steel V4A (AISI 316L) with sealing on both sides contact plate Ø 72 mm made of stainless steel V4A (AISI 316L) terminal lug with cross clamp for FL 40 x 4 mm or rod mm suitable for wall thicknesses up to 600 mm, bigger wall thicknesses on request suitable for bore holes Ø mm according to DIN 18014, DIN EN VDE (with lightning protection) mind. min. Wandstärke wall thickness 200 mm 200 mm Gewindestange threaded rod M16 cross-clamp Kreuzklemme for connecting zum Anschluss strip irons von Bandeisen up to 40 x 4 mm 30 x 3,5 mm rod Rd mm APPLICATION: standing seepage water, pressing water, waterproof concrete stress class 1 Entry for black tank HEA-W: for buildings with watertight external sealing according to DIN part 6, manufactured according to DIN part 9 (fixed/loose flange, Ø 210 mm) conductor core Ø 25 mm made of stainless steel V4A (AISI 316L) with threaded connection on both sides M12/M16 and additional cross clamp M20 as an external connection made of stainless steel V4A (AISI 316L) conductor core connection with M16 threaded bolts and lock nuts, galvanised contact plates Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holse minimum wall thickness 180 mm according to DIN 18014, DIN EN VDE (with lightning protection) inside Gebäudeaußenseite of building fixed Festflansch flange Gebäudeaußenseite loose Losflansch flange Gebäudeaußenseite Festflansch Festflansch membrane bolt 30 x 30 mm Dichtbahn Bolzen mm Losflansch Losflansch insulated isoliert Dichtbahn Dichtbahn Bolzen 30 x 30 mm isoliert Gebäudeaußenseite Festflansch cross-clamp Kreuzklemme for Losflansch connecting zum Anschluss strip irons von up Bandeisen to bis 40 x 4 mm Dichtbahn Kreuzklemme 40 x 4 mm Rd mm zum rod Anschluss 8-12 mm von Bandeisen reinforcing Armierungsstahl steel bis 40 x 4 mm Rd mm Armierungsstahl Kreuzklemme zum Anschluss von Bandeisen bis 40 x 4 mm Rd mm bolt Bolzen Ø Ø 25 mm Bolzen Bolzen 30 Ø x mm mm isoliert thread Gewinde M12 or oder M16 M16 min. mind. wall Wandstärke thickness mm mm Armierungsstahl mind. Wandstärke 180 mmmind. Wandstärke 180 mm Kreuzklemme zum Anschluss von Bandeisen bis 40 x 4 mm Rd mm Gewinde M12 Bolzen oder 30 M16 x 30 mm isoliert outside Gebäudeinnenseite of building connecting Anschlussbolzen bolt oder Gebäudeinnenseite M12 or M16 Gebäu Bolzen Ø 25 mm Gewinde M12 Bolzen oder Ø M16 25 mm Gewinde M12 oder M16 Anschlussbolzen M12 oder M16 Anschl M12 o Gebäude Anschlus M12 ode APPLICATION: Waterproof concrete stress class 1 Armierungsstahl mind. Wandstärke 180 mm Entry for double wall /element wall HEA-EW-M12: Wassersperre Schalungsscheibe Wassersperre water barrier protective Schalungsscheibe cover conductor core Ø 25 mm with a threaded connection on both sides M12 made of stainless steel V4A (AISI 316L) conductor core connection with M16 threaded bolts, galvanised 2 water barriers (profiled rubber flange, NBR) and 1 additional seal on the threaded bolt, the position of which can be adapted on site contact plates Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holes minimum wall thickness 180 mm according to DIN 18014, DIN EN VDE (with lightning protection) Ø 72 mm Ø 72 Ø mm 72 mm Ø 25 mm Ø 25 Ø mm 25 mm Ø 72 mm Ø 72 mm Ø 25 mm Ø 25 mm Wassersperre Gewinde M12 M12 Schalungsscheibe thread Gewinde M12 mind. mind. Wandstärke 180 mm 180 mm min. mind. wall Wandstärke thickness 180 mm 180 mm 48 Gewinde M12 M12 mind. mind. Wandstärke mm mm

49 Earthings ENTRIES HEA-N ENTRY FOR SUBSEQUENT INSTALLATION Entry for earthing connections, M16, stainless steel V4A (AISI 316L), for wall thicknesses up to 200 mm for subsequent installation HEA-N-M16/ Entry for earthing connections, M16, stainless steel V4A (AISI 316L), for wall thicknesses up to 600 mm for subsequent installation Entry for earthing connections, M16, stainless steel V4A (AISI 316L), for walls with perimeter insulation up to 200 mm, for wall thicknesses up to 400 mm for subsequent installation HEA-W ENTRY FOR BLACK TANK HEA-N-M16/ HEA-ND-M16/ X=wallthicknessinmm HEA-N-M16/X Entry HEA-W/x for buildings with watertight external sealing according to DIN part 6, manufactured according to DIN part 9 (fixed/ loose flange, Ø 210 mm), internal connection M12, cross clamp with threaded bolt M20 (min. wall thinkness 180 mm) Entry HEA-W/x for buildings with watertight external sealing according to DIN part 6, manufactured according to DIN part 9 (fixed/ loose flange, Ø 210 mm), internal connection M16, cross clamp with threaded bolt M20 (min. wall thickness 180 mm) HEA-W-M12/X HEA-W-M16/X X=wallthicknessinmm HEA-W-M12/X Extra HEA-EW ENTRY FOR DOUBLE WALL / ELEMENT WALL HEA-EW-M12/ HEA-EW-M12/ Entry for earthing connections made of stainless steel V4A (AISI 316L), connection M12 on both sides, with 3 water barriers and protective covers (min. wall thickness 180 mm) HEA-EW-M12/ HEA-EW-M12/ HEA-EW-M12/ HEA-EW-M12/ HEA-EW-M12/ HEA-EW-M12/ HEA-EW-M12/X 49

50 Earthings ENTRIES APPLICATION: Waterproof concrete stress class 1 Entry for flexible earthing connections HEA-F (insulated) / HEA-PF: 100 mm conductor core Ø 25 mm made of stainless steel V4A (AISI 316L) with threaded connection on both sides M12 or M16 pressure-tightwaterbarrier(profiledrubberflange,nbr) contact plate Ø 72 mm made of stainless steel V4A (AISI 316L) protective covers made of PE with four nail holes forwallthicknessesupto600mm,biggerwallthicknesses onrequest HEA-F:Cugroundstrap50mm2,finelystranded,insulated HEA-PF:steelcabledia.10mm,galvanized.Canbefastenedto reinforcementbarswithcrossclampz-k40-st37fvz according to DIN 18014, DIN EN VDE (with lightning protection) Ø 72 mm Ø 25 mm thread Gewinde M12 or oder M16 type: HEA-PF 100 mm min. mind. wall Wandstärke thickness mm mm max. Wandstärke wall thickness mm mm steel Stahlseil cable Ø 10 Ø mm10 mm protective Schalungsscheibe cover Ø 25 mm Ø 72 mm thread Gewinde M12 or oder M16 ACCESSORIES Connection bolt M12 with washer, lock washer and screw nut made of material St37 zinc-plated Connection bolt M16 with washer, lock washer and screw nut made of material St37 zinc-plated Connection bolt M12 with washer, lock washer and screw nut made of stainless steel V4A (AISI 316L) Connection bolt M16 with washer, lock washer and screw nut made of stainless steel V4A (AISI 316L) Four-wire connector with screwed-on threaded bolt M12 made of material St37 zinc-plated Four-wire connector with screwed-on threaded bolt M12 made of stainless steel V4A (AISI 316L) Four-wire connector with screwed-on threaded bolt M16 made of stainless steel V4A (AISI 316L) Four-wire connector with screwed-on threaded bolt M12 made of stainless steel V4A (AISI 316L) for buildings with perimeter insulation up to 80 mm Four-wire connector with screwed-on threaded bolt M16 made of stainless steel V4A (AISI 316L) for buildings with perimeter insulation up to bis 80 mm Connection terminal 70 x 70 mm made of St37 zinc-plated for flat belt 40 x 4 mm or circular conductor connection 8 12 mm Connection terminal 70 x 70 mm made of stainless steel V4A (AISI 316L) for flat belt 40 x 4 mm or circular conductor connection 8 12 mm Z-B-M12-St37 Z-B-M16-St37 Z-B-M12-V4A Z-B-M16-V4A Z-KG-M12-fvz Z-KG-M12-V4A Z-KG-M16-V4A Z-KG-D-M12-V4A Z-KG-D-M16-V4A Z-K40-St37-fvz Z-K40-V4A Z-B-M12-St37 Z-KG-M12-V4A Z-KG-D-M12 Z-K40-V4A 50

51 Earthings ENTRIES HEA-F/HEA-PF ENTRY FOR FLEXIBLE EARTHING CONNECTIONS Flexible, insulated earthing entry and copper (Cu) ground strap 50 mm² with connecting thread M12 for wall thicknesses up to 600 mm HEA-F-M12/ Flexible, insulated earthing entry and copper (Cu) ground strap 50 mm² with connecting thread M16 for wall thicknesses up to 600 mm HEA-F-M16/ Flexible earthing entry with steel cable Ø 10 mm galvanised and connecting thread M12 for wall thicknesses up to 600 mm Flexible earthing entry with steel cable Ø 10 mm galvanised and connecting thread M16 for wall thicknesses up to 600 mm HEA-PF-M12/ HEA-PF-M16/ ACCESSORIES Terminal lug for connecting earthing conductors, equipotential busbar or lightning protection technology, lug stainless steel V4A (AISI 316L), with connecting screw M12 Terminal lug for connecting earthing conductors, equipotential busbar or lightning protection technology, lug stainless steel V4A (AISI 316L), with connecting screw M16 Z-AL30-M Z-AL40-M Extra Hot-melt tape, cold-welding, length 3 m, width approximately 35 mm, eminently suitable as corrosion protection for earthing connectors Hatetherm Scapa

52 Fire protection for cables HVS / HSS GAS- AND WATERTIGHT FIREWALL S 90 FOR INSTALLATION IN WALL INSERT HSI 150, WALL SLEEVES AND CORE DRILLINGS DIBT-approval Z (HSS) purs. to DIN Z (HVS) purs. to DIN Firewall S 90 HVS / HSS: fire protection S 90 for core drillings mm diameter for plastic wall sleeves mm diameter for wall inserts HSI 150 (maximum package 2 x 6) insulation thickness 280 mm as of wall thickness 150 mm no additional wall construction necessary no limitation of individual cable diameters pads assembly possible from one side high flexibility for subsequent insertion no additional coating of cables necessary HSS installation fire-stop pads in wall insert HSI 150-K2, sealing with system cover or SEGMENTO HSS installation in core drillings with HRD press seals APPLICATION TABLE HSS System HSS HRD 150/160 for HSI 150 SEG = SEGMENTO D / DG System cover Core drilling/wall sleeve (with HRD) Wall thickness in mm Cable configuration Total insulation thickness in mm Size in mm results from sealing system selection after package formation HSI 150 (max. 2-row, 6 pieces in a row) Ø 70 (80) 200 Tightness in bar bis 2,5 0,5 bis 2,5 bis 5 Insulation thickness in mm Cable type Installation Comment all cables and cross sections except for wave guides no cable cross section limitation in masonry, concrete or aerated concrete walls configuration is limited by the sealing systems 52

53 Fire protection for cables HVS / HSS GAS- AND WATERTIGHT FIREWALL S 90 FOR INSTALLATION IN WALL INSERT HSI 150, WALL SLEEVES AND CORE DRILLINGS HVS/HSS FIRE PROTECTIONS SET AND TOOLS Item Core drilling/ wall sleeve diameter Article code Article number Picture Approval no: Z fire protection S 90, gastight Gastight fire protection set in connection with HRD consisting of: fire-stop pads 2x HVS-K250, bis Ø 100 mm HSS-100-KB/FR-HRD x HVS-KB-60, label, stainless steel belt Gastight fire protection set in connection with HRD consisting of: fire-stop pads 2x HVS-K400, 3x HVS -K250, 3x HVS-KB-60, 1 x label, stainless steel belt bis Ø 150 mm HSS-150-KB/FR-HRD Approval no: Z fire protection S 90 Fire protection set consisting of: fire-stop pads 3x HVS -K250/2, 5x HVS-KB-60, bis Ø 100 mm HVS-KK x label, 2x stainless steel belts Fire protection set consisting of: fire-stop pads 2x HVS-K400, 5x HVS -K250/2, 6x HVS-KB-60, 1x label, 2x stainless steel belts bis Ø 150 mm HVS-KK Fire protection set consisting of: fire-stop pads 2x HVS-K720, 2x HVS-K400, 5x HVS -K250/2, 8x HVS-KB-60, 1x label, 4x stainless steel belts bis Ø 200 mm HVS-KK Delivery without HRD rubber press seal. Fitting panel, for close-fitting installation of HVS/HSS fire-stop pads HVS/HSS-MB Extra UNIVERSAL FIRE-RESISTANT SEALING FOR CABLE ENTRY HSI 150 Item Sealing Article code Article number Picture Approval no: Z fire protection S 90 Fire protection set consisting of: fire-stop pad 1x HVS-K720, 1x HVS-K400, 4x HVS -K250/2, 4x HVS-KB-60, label, stainless steel belt SEGMENTO Systemdeckel HSS-150/SEG/D/DG Fire protection set consisting of: fire-stop pads 2x HVS-K400, 3x HVS-K250, 3x HVS-KB-60, label, stainless steel belt HRD-press seal HSS-150/HRD Delivery without HRD rubber press seal, SEGMENTO respectively system cover. 53

54 Roof entries SHD SWAN NECK ROOF ENTRY Swan neck roof entry SHD: flexible, modular system suitable for all flat roof structures individual components, thus low transport weight height (min. 300 mm) and orientation can be adjusted (can be swivelled through 360 ) even after installation available in 4 sizes, 100, 150, 200 and 300 mm diameters all steel parts are hot-dip galvanized sealing of cables in swan neck after installing the cables possible with split sealing insert SKD (pressure plates made of stainless steel V2A (AISI 304L), rubber quality EPDM) pipe elbow 90 pipe elbow 30 Type A (mm) B (mm) C ( mm) D (Ø i mm) E ( mm) SHD SHD intermediate pipe (can be removed) SHD SHD drip cap height-adjustable extension pipe header membrane A B A = min./max. telescope range B = overall height C = hole pattern 4 x 12 mm diameter D = max. core drilling diameter E = base plate edge dimension insulation D C E membrane base plate Installed SHD 200 before laying of cables Swan neck entry SHD 200 complete with seal insert SKD 54

55 Roof entries SHD SWAN NECK ROOF ENTRY SHD SWAN NECK ROOF ENTRY Swan neck roof entry, nominal diameter = 100 mm, for dowelling above core drilled holes, rotatable by 360, height-adjustable SHD Swan neck roof entry, nominal diameter = 150 mm, for dowelling above core drilled holes, rotatable by 360, height-adjustable SHD Swan neck roof entry, nominal diameter = 200 mm, for dowelling above core drilled holes, rotatable by 360, height-adjustable SHD Swan neck roof entry, nominal diameter = 300 mm, for dowelling above core drilled holes, rotatable by 360, height-adjustable SHD SKD CABLE SEALING FOR SWAN NECK Seal insert, for swan neck SHD 100 (pressure plates made of stainless steel V2A (AISI 304L), rubber quality EPDM) SKD 100-2G-Z/d Seal insert, for swan neck SHD 150 (pressure plates made of stainless steel V2A (AISI 304L), rubber quality EPDM) SKD 150-2G-Z/d Extra Seal insert, for swan neck SHD 200 (pressure plates made of stainless steel V2A (AISI 304L), rubber quality EPDM) SKD 200-2G-Z/d Seal insert, for swan neck SHD 300 (pressure plates made of stainless steel V2A (AISI 304L), rubber quality EPDM) SKD 300-2G-Z/d Z = number of cables d = measured cable diameter 55