GRID SYSTEM ECOPLUS SYSTEMS TWO-WAY EXPOSED SUSPENDED CEILING GRID SYSTEM
|
|
- Scot Flynn
- 5 years ago
- Views:
Transcription
1 TWO-WAY EXPOSED SUSPENDED CEILING GRID SYSTEM TWO-WAY EXPOSED SUSPENDED CEILING GRID SYSTEM Ver 1.0 Dec. 2010
2 CONTENTS 3: TWO-WAY COMPONENTS & APPLICATION DETAIL 4: INSTALLATION DETAILS 5: INSTALLATION DETAILS CONTINUED TWO-WAY EXPOSED SUSPENDED CEILING GRID SYSTEM 6: PRODUCT DATA SPECIFICATIONS 7: CONTACT DETAILS
3 TWO-WAY COMPONENTS PRIMARY SECTIONS WALL ANGLE/ BULKHEAD TRIM ECOPLUS Main Tee ECOPLUS Cross Tee ECOPLUS Wall Angle Trim Steel 24 x 24mm APPLICATION DETAILS NOTE: Fixings used for direct hanging with wire are determined by building material above ceiling system (eg: concrete, timber or steel). Selected fixing ECOPLUS Ceiling Tiles Galvanised wire 2.5mm ECOPLUS Cross Tee ECOPLUS Main Tee ECOPLUS Two-Way Exposed Ceiling System Detail ECOPLUS CROSS TEE REMOVAL 3
4 INSTALLATION DETAILS TWO-WAY EXPOSED GRID SYSTEM NOTE: Work shall comply with the installation requirements of AS/NZS 2785:2000 by appropriately qualified trade contractors. All ceilings must be designed in accordance with the requirements of AS/NZS As part of this design process, seismic compliance to AS/NZS is required. Installation should not commence until the building is weathertight Refer AS/NZS STEP ONE The room must be checked on site to determine if it is out of square. Using the 3/4/5 method (Figure 1.) will assist in squaring up the room before installation. Layout ceiling grid module to datum shown on architects drawings, or give equal cut tiles at perimeter walls (refer Figure 2.) Work out an even margin along the sides and at both ends. EXAMPLE: (refer Figure 2.) MAIN TEE 4m divided by tile length (1.2m) = 3.3 tile modules. 4m less 3.6m (ie. 3 full tile lengths) = 400mm. Take 400mm and add one tile length (1.2m) = 1.6m. Divide 1.6m by 2 = 800mm margin along each side. CROSS TEE 5m divided by tile length (mm) = 8.3 tile modules. 5m less 4.8m (ie. 3 full tile lengths) = 200mm. Take 200mm and add one full tile width (mm) = 800mm. Divide 800mm by 2 = 400mm margin along each side. STEP TWO Mark each wall to the correct height of the ceiling. Cut the Perimeter wall angle trim to length, and fix to wall with suitable fasteners Eg: Gib grabber wafer head needle tip - at mm maximum centres. (Refer Figure 3.) The Wall Angle should be mitred at corner sections to provide an attractive appearance STEP THREE Fix the Main Tee suspension wire hanger at 1200mm centres maximum along supporting members (ie Purlins,Trusses, Concrete), with a Main Tee span of 1200mm. Fasteners to supporting structure to have a minimum ultimate design load capacity of 0.5kN. 4m WALL 5m WALL Figure 1: Using the 3/4/5 method to square up a room. Figure 2: Working out even margins. Figure 3: Perimeter wall angle trim. Fix with wafer head needle tip. 4
5 INSTALLATION DETAILS TWO-WAY EXPOSED GRID SYSTEM CONTINUED STEP FOUR Cut the Main Tee to length so that the first pre-punched cross tee slot as determined in Step One. (Figure 4.) STEP FIVE Install the Main Tee. The self locking tag ends are then pushed together to lock into position, leaving a hairline connection as detailed. STEP SIX With a gentle push, install Cross Tee at mm centres (to form a 1200 x mm grid) between Main Tee through pre-punched slots to form the required grid module. To give the required grid module, ensure positive locking of both Cross Tee connections into each other. (Refer Figure 5.) STEP SEVEN Level and align grid. The suspension points can be adjusted to either a string line or laser. Self-locking tag ends Self-locking tag ends Cross Tee Main Tee Self-locking tag ends Figure 4: Suspension tie-wire detail support hangers at maximum 1200mm centres on the Main Tee. Figure 5: Tee jointing details. 5
6 PRODUCT DATA SPECIFICATIONS For technical details refer to ECOPLUS Systems BUILDING PRODUCT QUALITY PLAN available on request. MATERIAL SPECIFICATIONS ECOPLUS Two-Way Exposed Grid Main and Cross Tee base sections are double-web cold roll formed from hot dipped, zinc-coated galvanised steel strip. The exposed capping face is cold rolled formed onto the base section also from hot dipped, zinc-coated galvanised steel strip with a factoryapplied polyester paint finish. Steel Yield Strength fy=270mpa minimum. ECOPLUS acoustic panel (2.4kg/m 2 ) to be used for ceiling. Suspension wire, 2.5mm diameter galvanised wire with minimum coating of 125g/m 2 MAIN TEE MASS 0.30kg per lineal meter CROSS TEE MASS 0.24kg per lineal meter ADDITIONAL LOADS The suspension system is designed to carry the weight of the ceiling only. Additional loads are not to be placed upon or carried by the suspension system mm thick ECOPLUS 24mm Main Tee Length 3 0.3mm thick ECOPLUS 24mm Cross Tee Length mm thick ECOPLUS Wall Angle Trim Length
7 C O N T A C T Chris Holden Sales and Marketing Manager Moblie chris@ecoplus-systems.com ecoplus-systems.com PO Box Auckland City Auckland
FASTLOCK SUSPENDED CEILING GRID ECOPLUS SYSTEMS. FasTLock SUSPENDED CEILING GRID. Stronger, more durable
ECOPLUS SYSTEMS FASTLOCK SUSPENDED CEILING GRID FasTLock SUSPENDED CEILING GRID Ver 3.0 Dec. 2011 ECOPLUS SYSTEMS CONTENTS 3: The FasTLock Advantage 4: FasTLock product detail 5: FasTLock 15 product detail
More information7 th October, Bailey Interiors / Australian Plaster Acoustics Boundary Rd Mortdale NSW Attn: Roger Bailey Ref: A
7 th October, 205 Bailey Interiors / Australian Plaster Acoustics 83-85 Boundary Rd Mortdale NSW 2223 Attn: Roger Bailey Ref: 4562 5 00A Warranty Confirmation: Rondo Building Services Pty Limited ABN 69
More informationEXPOSED GRID CEILING SYSTEMS INSTALLATION GUIDE
EXPOSED GRID CEILING SYSTEMS INSTALLATION GUIDE rondo duo EXPOSED GRID CEILING SYSTEM VARIOUS RONDO DUO COMPONENTS INTRODUCTION Rondo DUO Exposed Grid Ceiling System is a practical ceiling system which
More informationd u o installation guide duo Exposed Grid Ceiling System
d u o installation guide duo Exposed Grid Ceiling System rondo duo Typical Application Details. Select your preferred grid layout to suit either 200 x or x ceiling panels as shown in Table, selecting the
More informationRondo duo. Two-Way Exposed Suspended Ceiling Grid System. revised: august 2008
Rondo duo Two-Way Exposed Suspended Ceiling Grid System revised: august 2008 design considerations general information All components of the Rondo DUO Exposed Ceiling Grid System have been designed and
More informationSHORTSPAN. Features. Components
Armstrong DGS ShortSpan is a fast and easy solution for framing short spans and an economical alternative to TCR and Furring Channel constructions. Features ShortSpan enables framing without suspension
More informationduo installation guide DUO Exposed Grid Ceiling System
duo installation guide DUO Exposed Grid Ceiling System rondo duo EXPOSED GRID CEILING SYSTEM GENERAL INFORMATION This brochure provides details of the Rondo DUO Exposed Grid Ceiling System, which allows
More informationROCKFON SYSTEM T24 A/E
System description ROCKFON SYSTEM T24 A/E Versatile ceiling system Quick and easy to install Visible grid Easy integration with services and fittings Ceiling comprising Chicago Metallic T24 Click 2890
More informationSRP CEILING SYSTEMS HANDBOOK
SRP CEILING SYSTEMS HANDBOOK CONTENTS SRP Ceiling Product Range 3 Strength and Durability 7 Service 7 Use Only the Current Specification 8 Purpose 8 Scope of Use 8 Materials Table 1 8 Performance of Ceiling
More informationRondo DUO. Two-Way Exposed Suspended Ceiling Grid System
Rondo DUO Two-Way Exposed Suspended Ceiling Grid System DESIGN CONSIDERATIONS GENERAL INFORMATION All components of the Rondo DUO Exposed Ceiling Grid System have been designed and tested by Rondo engineers
More informationROCKFON SYSTEM T24 A/E
System description ROCKFON SYSTEM T24 A/E Versatile ceiling system Quick and easy to install Visible grid Easy integration with services and fittings Ceiling comprising Chicago Metallic T24 Click 2890
More informationTHIS SECTION IS BASED ON ROCKFON S TRADITIONS METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S TRADITIONS METAL CEILING PANELS. Rockfon Traditions Metal Ceiling Panels are meant for interior applications, specifications as shown here pertain to interior
More informationTHIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S CURVGRID ONE-DIRECTIONAL CURVED METAL CEILING PANELS. Rockfon CurvGrid One-Directional Curved Metal Ceiling Panels are meant for interior applications, specifications
More informationPEAKFORM SUSPENSION SYSTEMS
PEAKFORM SUSPENSION SYSTEMS THE PEAKFORM RANGE: WHERE INNOVATION MEETS PERFORMANCE PeakForm is a comprehensive range of suspended ceiling grid solutions designed to meet most commercial design requirements:
More informationSECTION NON-STRUCTURAL METAL FRAMING
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 09 22 16 1. Use this section only for NCA projects. 2. Delete between //----// if not applicable to project. Also delete any other item or paragraph not applicable
More informationSECTION Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco Ceramic Tile.
SECTION 09510 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310 - Ceramic Tile. 1.02 REFERENCES A. American
More informationPEAKFORM SUSPENSION SYSTEMS
PEAKFORM SUSPENSION SYSTEMS THE PEAKFORM RANGE: WHERE INNOVATION MEETS PERFORMANCE PeakForm is a comprehensive range of suspended ceiling grid solutions designed to meet most commercial design requirements:
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationROCKFON SYSTEM ULTRALINE E
System description ROCKFON SYSTEM ULTRALINE E Visible grid ceiling system SYSTE F unctional recess allows for the easy integration of partitions, track lighting and signage E15S8 EDGE WAR YEARS IT LIM
More information***************************************************************************************************************
09510 ACOUSTICAL CEILINGS SPECIFIER: CSI MasterFormat 2004 number 09 51 00 PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310
More informationSECTION Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco Ceramic Tile.
SECTION 09510 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09200 - Metal Studs, Lath, Suspension Ceilings, Plaster, and Stucco. 2. 09310 - Ceramic Tile. 1.02 REFERENCES A. American
More informationSECTION (09512) - ACOUSTICAL TILE CEILINGS
SECTION 09 51 23 (09512) - ACOUSTICAL TILE CEILINGS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Suspended Metal Grid Systems Complete With Wall Trim 2. Suspended Fiberglass Grid Systems Complete
More informationMETALWorkS. RH200 Custom Hook-on Panels. General Installation Instructions. Ceiling 1.0 GENERAL Site Conditions Product Description
Ceiling Systems Between us, ideas become reality METALWorkS General Installation Instructions RH200 Custom Hook-on Panels 1.0 GENERAL 1.1. Product Description RH200 system is a downward accessible, metal
More informationBanyan Air Service November 18, 2011 AVE Aviation and Commerce Center Building 1 Miami, FL
SECTION 09511 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationCEILING SYSTEMS. PeakForm. Between us, ideas become reality SUSPENSION SYSTEMS
CEILING SYSTEMS Between us, ideas become reality PeakForm SUSPENSION SYSTEMS The PeakForm Range: WHERE INNOVATION MEETS PERFORMANCE PeakForm is a comprehensive range of suspended ceiling grid solutions
More informationInstallation guide. ROCKFON System Z mm. 600 mm
Installation guide 600 mm ROCKFON tiles with the D edge detail are suitable for installation using this system. The following ceiling tile module sizes (mm) can be used with : 1500 x 600 1800 X 600 100
More informationBasic Suspension Systems
CEILING & WALL SYSTEMS Commercial Ceilings and Walls Solutions Guide Installing Armstrong Suspended Ceilings The ceiling system is made up of Armstrong panels which are supported by a suspension system
More informationDONN Suspension Systems
DONN Suspension Systems CI/SfB from the industry leader u (35) Xh2 DONN grid syst innovation and quality you USG is the world s leading manufacturer of ceiling grid, offering the widest range of profiles
More informationTHIS SECTION IS BASED ON ROCKFON S SPANAIR HOOKON METAL CEILING PLANKS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S SPANAIR HOOKON METAL CEILING PLANKS. Rockfon SpanAir HookOn Metal Ceiling Planks are meant for interior applications, specifications as shown here pertain to interior
More informationAND ACCESSORIES FOR DRYWALL CONSTRUCTION
STEEL TRIMS AND ACCESSORIES FOR DRYWALL CONSTRUCTION Quality in your corner. THE STRENGTH WITHIN MONTREAL TORONTO CALGARY EDMONTON VANCOUVER STEEL TRIMS AND ACCESSORIES for Construction BAILEY HAS YOUR
More informationTHIS SECTION IS BASED ON ROCKFON S PLANOSTILE D LAY-IN METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S PLANOSTILE D LAY-IN METAL CEILING PANELS. Though Rockfon Planostile D Lay-In Metal Ceiling Panels are meant for interior and exterior applications, Specifications
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. AC: Articulation
More informationROCKFON SYSTEM T24 X
System description ROCKFON SYSTEM T24 X Concealed ceiling system Continuous expression GRP SYSTE E asy integration of services X EDGE WAR YEARS IT LIM ED Quick and easy to install M NT Y L ow installation
More informationrondo accessories CONTENTS:
rondo accessories SUMMARY Rondo has a range of accessories to complement our steel wall and ceiling systems, which includes Top Hats, Reveal Beads and Angles, as well as a rod bending tool for suspended
More informationConstruction Standards PAGE
Construction Standards PAGE 095113-1 SECTION 095113 - PART 1 - GENERAL 1.1 M.S.U. ISSUES 1. It the intent of MSU that all joint sealants used on its projects will comply with LEED NC 3 Credit Requirements
More informationSUSPENSION REQUIREMENTS SEE DETAIL B1.2 TYPICAL SYSTEM SECTION SEE DETAIL 'A' THIS SHEET 2" MODULE. SPECIFICATIONS (unless noted otherwise)
1 5 32 " 2" 27 32 " REQUIRED FOR 1 1 4 " 113 32 " 2 21 32 " SEE DETAIL B1.2 CARRIER SPAN VARIES DEPENDING ON DESIGN WIND PRESSURE 12 GA HANGER WIRE, BY OTHERS, NOT BY HUNTER DOUGLAS SEE DETAIL B1.2 12
More informationMake Waves. Topo 3-Dimensional System
Make Waves Topo 3-Dimensional System User s Guide Topo panels are offered in translucent and opaque to work with existing lighting and complement any color palette. Optional preengineered utility circles
More informationSECTION ACOUSTICAL TILE. *(Filed Sub-Bid Required) 1.00 TIME, MANNER AND REQUIREMENTS FOR SUBMITTING SUB-BIDS
SECTION 090003 *(Filed Sub-Bid Required) PART 1 GENERAL 1.00 TIME, MANNER AND REQUIREMENTS FOR SUBMITTING SUB-BIDS A. Sub-bids shall be submitted in accordance with provisions of the General Laws (Ter.
More informationA. Product Data: Submit manufacturer's descriptive literature, and recommendations and instructions for installation.
SECTION 09512 - ACOUSTICAL TILECEILINGS (ACT-01 and ACT-02) PART 1 - GENERAL 1.01 SUMMARY A. Section includes ceilings consisting of acoustical panels and exposed suspension systems. This ceiling system
More informationCI/SfB. October RockLink 15. Installation system
CI/SfB (5) Xh2 October 2008 RockLink 15 Installation system RockLink 15 Rockfon tiles with A15 and E15 edge 1 6 2 details are suit able for installation using this system. 5 6 2 6 4 The following ceiling
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationCEILING SYSTEMS. Between us, ideas become reality. PeakForm SUSPENSION SYSTEMS
CEILING SYSTEMS Between us, ideas become reality PeakForm SUSPENSION SYSTEMS The PeakForm Range: WHERE INNOVATION MEETS PERFORMANCE PeakForm is a comprehensive range of suspended ceiling grid solutions
More informationDIVISION: FINISHES SECTION: SUSPENSION SYSTEMS SECTION: ACOUSTICAL CEILING SUSPENSION ASSEMBLIES REPORT HOLDER:
0 ICC-ES Report ICC-ES (800) 423-6587 (562) 699-0543 www.icc-es.org 000 Most Widely Accepted and Trusted ESR-3336 Reissued 01/2015 This report is subject to renewal 01/2017. DIVISION: 09 00 00 FINISHES
More informationSECTION AXIOM INDIRECT FIELD LIGHT COVE PERIMETER SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 09 51 13 AXIOM INDIRECT FIELD LIGHT COVE PERIMETER SYSTEM PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of Contract, including General and Supplementary Conditions and
More informationSECTION LINEAR METAL CEILINGS
SECTION 09 5423 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and other Division 01 Specification Sections, apply
More informationDIVISION: FINISHES SECTION: SUSPENSION SYSTEMS SECTION: ACOUSTICAL CEILING SUSPENSION ASSEMBLIES REPORT HOLDER:
0 Most Widely Accepted and Trusted ICC-ES Evaluation Report ICC-ES 000 (800) 423-6587 (562) 699-0543 www.icc-es.org ESR-3336 Reissued 01/2017 This report is subject to renewal 01/2019. DIVISION: 09 00
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationInstallation Guide December 2012
Guide December 2012 Guide Description USG Compositions are decorative ceiling clouds offered in convenient, ready-to-assemble kits. Compositions allow you to create a custom look, accentuate an area or
More informationRockfon System T24 Stepped Z D
Part of the ROCKWOOL Group Rockfon System T24 Stepped Z D System Description D-edge Clip 120 Concealed ceiling system Continuous expression -- Elegant, continous ceiling expression -- Every single tile
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 092216 - NON-STRUCTURAL METAL FRAMING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationROCKFON SYSTEM T24 XL A, E
System description ROCKFON SYSTEM T24 XL A, E Visible/Semi-concealed ceiling system Standard A EDGE E very tile is demountable and fewer hangers allow easy access to ceiling voids SYSTE GRP WAR YEARS NT
More informationMETALWORKS RH215 Faceted Custom Hook-on Panels
METALWORKS RH215 Faceted Custom Hook-on Panels Assembly and Installation Instructions 1. GENERAL 1.1 Product Description MetalWorks RH215 Faceted Custom Hook-on panel system is a downward accessible, custom
More informationCI/SfB. June RockLink 24 Monolith. Installation system
I/SfB (35) Xh2 June 2008 RockLink 24 Monolith Installation system RockLink 24 Monolith Gypsum / MF plasterboard border Rockfon s with edge detail D in module size x are suit able for installation using
More informationSECTION ACOUSTICAL CEILINGS
SECTION 09511 ACOUSTICAL CEILINGS PART 1 GENERAL 1.01 SECTION INCLUDES A. Acoustical ceiling panels. B. Exposed grid suspension system. C. Wire hangers, fasteners, main runners, cross tees, and wall angle
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 092216 - COLD FORMED STEEL FRAMING - NON-STRUCTURAL (CFSF-NS) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 ACTION
More information4 " " SEE DETAIL B1.2. SPECIFICATIONS (unless noted otherwise)
REQUIRED FOR DETAIL 7 1 8 " 7 8 " SUSPENSION REQUIREMENTS SEE DETAIL B1.2 8" 7 1 1 8 " 4 " 2 1 8 " SEE DETAIL B1.2 CARRIER SPAN VARIES DEPENDING ON DESIGN WIND PRESSURE 12 GA HANGER WIRE, BY OTHERS, NOT
More informationStore No MAY 13 Addendum No. 1 SECTION ACOUSTICAL PANEL CEILINGS
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSTEEL STUD, TRIMS AND ACCESSORIES FOR DRYWALL CONSTRUCTION MONTREAL TORONTO CALGARY EDMONTON VANCOUVER THE STRENGTH WITHIN
STEEL STUD, TRIMS AND ACCESSORIES FOR DRYWALL CONSTRUCTION MONTREAL TORONTO CALGARY EDMONTON VANCOUVER THE STRENGTH WITHIN STEEL STUD AND TRACK FOR DRYWALL PARTITIONS TAKE ADVANTAGE OF THE SAVINGS IN TIME
More informationGeneral applications. Fast. Easy. Customer Focused.
C E I L I N G S U S P E N S I O N S Y S T E M S Fast. Easy. Customer Focused. General applications 200 Snap-Grid (Hook) /16) 250 Fire-Front Snap-Grid (Hook) /16) Seismic 1200 & 1200 (Stab) /16) 1250 Fire-Front
More informationA. ASTM C635, Standard Specifications for Metal Suspension Systems. B. ASTM C636, Recommended Practice for Installation of Metal Suspension System
SECTION 09510 / 09 51 00 USG TRUE WOOD LINEAR PANELS Product Specification WOOD CEILING PANELS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General
More informationSECTION ACOUSTICAL PANEL CEILINGS
SECTION 095113 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationProject No: Pakenham Branch Library, Pakenham, Ontario Section DECEMBER, 2016 Page 1 of 6
DECEMBER, 2016 Page 1 of 6 1 GENERAL 1.01 RELATED SECTIONS.1 Section 01 33 00 - Submittal Procedures..2 Section 07 21 16 - Batt and Blanket Insulation..3 Section 07 92 10 - Sealants..4 Section 09 91 00
More informationBear Exhibit Fence Upgrades. The following modifications are hereby made part of the contract documents:
ADDENDUM TO BID T2017-04 Metropolitan Park District Department of Planning, Design and Development 4702 South 19 th Street Tacoma WA 98405 Date Prepared: November 17, 2017 Bid Number: T2017-04 Addendum
More informationStudent Services & Classroom Addition
SECTION 095133 - ACOUSTICAL METAL PAN CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01
More informationSoundmaster & Modernfold TECHNICAL DATA
This specification along with product information and model details can be downloaded from www.modernfold.com SPECIFICATION - SECTION 08 35 13 ACCORDION FOLDING DOORS PART 1 - GENERAL 1.1 RELATED DOCUMENTS
More information6" MAX CARRIER OVERHANG, TYP. MAX CARRIER SPACING VARIES DEPENDING ON DESIGN WIND PRESSURE, SEE DETAIL B1.2, TYP.
5 7 8 " NOM. 2" TYPICAL SYSTEM SECTION VERTICAL SUPPORT SPACING VARIES DEPENDING ON DESIGN WIND PRESSURE, SEE DETAIL B1.2, TYP. CARRIER SPLICE SEE DETAIL B1.4 6" MAX CARRIER OVERHANG, TYP. 1 12 GA HANGER
More informationLINEAR METAL CEILINGS Section
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
More informationSPECIFICATIONS (unless noted otherwise)
2" 150F SYSTEM PROFILE 5 7 8 " NOM. CARRIER SPLICE SEE DETAIL B1.4 12 GA HANGER WIRE, BY OTHERS, NOT BY HUNTER DOUGLAS SEE DETAIL B1.2 DETAIL 'A' TYPICAL SYSTEM SECTION SEE DETAIL 'A' THIS SHEET 1 VERTICAL
More informationsystem 130 modular lay-in tiles (exposed grid) SAS International +44 (0)
metal ceilings system 130 modular lay-in tiles (exposed grid) SAS International +44 (0) 118 929 0900 www.sasint.co.uk system 130 information System Description SAS System 130 is a range of lay-in tiles
More informationSECTION DRYWALL GRID LINEAR LIGHTING INTEGRATION
SECTION 09 22 26 DRYWALL GRID LINEAR LIGHTING INTEGRATION PART 1 - GENERAL 1.1 RELATED DOCUMENTS Drawings and general conditions of Contract, including General and Supplementary Conditions and Divisions-1
More informationRockfon System Maxispan T24 A, E
System description Rockfon System Maxispan T24 A, E Ceiling systems for special applications Corridor A-EDGE GRP SYSTE M WAR YEARS NT Y U p to 3 m span due to the strength of the profiles N o need for
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 095423 - LINEAR METAL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCode Compliance Meets the requirements for suspended ceilings in accordance with the 2012 International Building Code.
Pei Evaluation Service is an accredited ISO Standard 17065 Product Certifier, accredited by the IAS. This Product Evaluation Report represents a product that Pei ES has Evaluated and this product has a
More informationPRESTON HEALTH SERVICES ARCHITECT'S NO. 2700
SECTION 09 5113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationAdjustable Suspension Hanger Technical Datasheet
Adjustable Suspension Hanger sheet The Adjustable Suspension Hangers Clip are a component of the Keylock Ceiling System. The upper vertical side of the hanger allows the Suspension Rod that goes through
More informationSECTION COMPOSITE CORE ACOUSTICAL PANEL CEILINGS. Sound-Rite Inc. #9, rd Avenue NE Calgary, AB T2A 7P3
SECTION 09510 COMPOSITE CORE ACOUSTICAL PANEL CEILINGS Sound-Rite Inc. #9, 2821 3rd Avenue NE Calgary, AB T2A 7P3 Tel 403-296-0505 Fax 403-296-0511 Email info@sound-rite.com Web www.sound-rite.com Techstyle
More informationtechnicalnote Seismic Category D, E, F Installation Details Fully Concealed Rockfon CDX FIELD INSTALLATION Grid
technicalnote Seismic Category D, E, F Installation Details Fully Concealed Rockfon CDX Rockfon fully concealed CDX panels have been shake table tested under the following conditions; the installation
More informationDIVISION 5 METALS SECTION COLD-FORMED METAL FRAMING
DIVISION 5 METALS SECTION 05 40 00 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationSystem F - Free Span Systems
System F - Free Span Systems System F 1.1: THERMATEX GN (non) demountable System F 1.2: THERMATEX AW demountable System F 1.3: THERMATEX VT demountable System F 4.1: MONDENA corridor system System F as
More informationSECTION STEEL DECKING
SECTION 05 31 00 STEEL DECKING SPEC WRITER NOTE: 1. Delete text between // // not applicable to project. Edit remaining text to suit project. 2. Refer to Section 05 36 00, COMPOSITE METAL DECKING for floor
More informationRockfon Concealed Acoustical Ceiling Systems (CDX) for Seismic Category D, E, F Applications
Part of the ROCKWOOL Group Rockfon Concealed Acoustical Ceiling Systems (CDX) for Seismic Category D, E, F Applications Installation Guide Project Lions Park Søllerød in Nærum, Denmark Products Rockfon
More informationProduct Guide Specification
ALGRIP Manufactured by April 2017 104 North Maple Avenue P.O. Box 646 Leola, Pennsylvania 17540 Toll Free 800-345-8170 Fax 717-656-2041 Website www.algrip.com / www.rosstechnology.com E-mail sales@rosstechnology.com
More informationPLANK AND LARGE PANEL STABILIZER BARS APPLICATION GUIDE
USG Ceiling Solutions PLANK AND LARGE PANEL STABILIZER BARS APPLICATION GUIDE PLANK AND LARGE PANEL CEILING SYSTEMS Market demands for plank and large panel ceiling systems such as the USG Ceiling Systems
More information1222 Moonshine Rd, RD1, Porirua 5381 Private Bag Porirua 5240, New Zealand Tel: branz.co.nz. Important Notice
1222 Moonshine Rd, RD1, Porirua 5381 Private Bag 50 908 Porirua 5240, New Zealand Tel: 04 237 1170 branz.co.nz Important Notice Since the issue of this Appraisal, a revised version of the Approved Document
More informationSAS International Ltd. System 120 By SAS International Ltd. Product summary page for System 120 generated by ribaproductselector.
SAS International Ltd System 120 By SAS International Ltd Detailed description A range of square and rectangular clip-in metal ceiling tiles designed to take support from Emac proprietary spring tee suspension
More informationSECTION COMPOSITE METAL DECKING
PART 1 GENERAL 1.1 DESCRIPTION SECTION 05 36 00 1. Use this section only for NCA projects. 2. Delete between // ---- // if not applicable to project. Also delete any other item or paragraph not applicable
More informationEasy Elegance Ceiling Panel Installation Instructions
DESIGN CONSIDERTIONS Clearance: Easy Elegance ceiling panels are a drop/suspended ceiling, using rmstrong Prelude 15/16-in Grid. You will need to have approximately 6-in of clearance above the grid face
More informationSECTION ( Specialty Ceilings) TBAR LED Smartlight Acoustical Ceiling Integration
SECTION 09 50 00 (09 54 00 Specialty Ceilings) TBAR LED Smartlight Acoustical Ceiling Integration PART 1 - GENERAL 1.1 RELATED DOCUMENTS 1.2 SUMMARY Drawings and general conditions of Contract, including
More informationTHIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS.
PAGE 1 THIS SECTION IS BASED ON ROCKFON S PLANOSTILE SNAP-IN METAL CEILING PANELS. Though Rockfon Planostile Snap-In Metal Ceiling Panels are meant for interior and exterior applications, Specifications
More informationA. ASTM C635, Standard Specifications for Metal Suspension Systems. B. ASTM C636, Recommended Practice for Installation of Metal Suspension System
SECTION 09510 / 09 51 00 USG TRUE WOOD LAY IN AND ACCESSIBLE REVEAL Product Specification WOOD CEILING PANELS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract,
More informationSECTION ACOUSTICAL CEILINGS
PART 1- GENERAL 1.1 DESCRIPTION SECTION 09 51 00 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph not applicable
More informationROCKFON SYSTEM T24 A/E ECR
System description ROCKFON SYSTEM T24 A/E ECR Enhanced corrosion resistant ceiling systems for humid environments A EDGE C orrosion resistance Class D (EN 13964) YEARS IT LIM ED GRP WAR NT Y E very single
More informationNORTILE LAV-IN, LAY-ON. Metal Ceilings
NORTILE LAV-IN, LAY-ON Metal Ceilings fl1e l ntlllt..1 INTRODUCTION The Lay-in I Lay-on System is one of the most simplified and economical system in its range. This system is a modular ceiling available
More informationAXIOM Direct Light Coves Assembly and Installation Instructions
AXIOM Direct s Assembly and Installation Instructions 1. GENERAL 1.1 Description The Axiom Direct system is a pre-engineered lighting solution designed to be used at a wall condition and integrate with
More informationElectrical Services Standard Specification Cable Tray Installation. May For ROYAL HOLLOWAY UNIVERSITY OF LONDON
Electrical Services Standard Specification 4.0 - Cable Tray Installation May 2010 For ROYAL HOLLOWAY UNIVERSITY OF LONDON Prepared For The Estates Division By: Hulley & Kirkwood Consulting Engineers Ltd
More informationOCALA INTERNATIONAL AIRPORT MBI PN: GENERAL AVIATION TERMINAL JANUARY 16, 2018 ADDENDUM-ISSUE
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification
More informationSEISMIC RESTRAINT SYSTEM
1. GENERAL 1.1. Description: SECTION 16012 SEISMIC RESTRAINT SYSTEM 1.1.1. This specification covers design and installation of seismic bracing and anchorage required for conduit, cable tray, bus duct,
More informationShortSpan Brochure1 6/14/05 4:39 PM Page 1 CEILING SYSTEMS
CEILING SYSTEMS Armstrong Short Drywall Grid System was introduced to the North American commercial building market early in 2005. Many of its properties are similar to other framing systems commonly
More informationDoc
ANC-45 ACCORDION DOOR ACCORDION FOLDING PARTITIONS, WALLS OR DOORS GENERAL NOTES TO SPECIFIER: This specification section has been prepared to assist design professionals in the preparation of project
More information