ASSEMBLY INSTRUCTIONS. Due to continuing improvements, actual product may differ slightly from the product described herein.

Transcription

1 BISTRO SET PIECE WROUGHT IRON 9246 ASSEMBLY INSTRUCTIONS Due to continuing improvements, actual product may differ slightly from the product described herein. 49 Mission Oaks Blvd., Camarillo, CA 90 Visit our Web site at Copyright 2005 by Harbor Freight Tools. All rights reserved. No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools. For technical questions and replacement parts, please call

2 Specifications Table Diameter Materials Chair Dimensions Max. Table Capacity Max. Seat Capacity Net Weight 29-/4 Dia. Chair; Wrought Iron Frame w/polyester Fabric. Table; Wrought Iron Legs w/ Aluminum Table Rim and 5mm Tempered Glass; Rubber Feet 4 H x 8 W x 2-/2 D Lbs. 225 Lbs. 52 Lbs. Save This Manual You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry place for future reference. Safety Warnings and Precautions WARNING: When using this product, basic safety precautions should always be followed to reduce the risk of personal injury and damage to equipment. Read all instructions before using this product!. KEEP PRODUCT USAGE AREA CLEAN. Cluttered areas invite injuries. 2. SUPERVISE CHILDREN AROUND THIS PRODUCT. Do not allow children to climb upon these chairs or table top.. DO NOT ASSEMBLE THIS PRODUCT IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS. Read warning labels on prescriptions to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not attempt to assemble this product. 4. USE EYE PROTECTION. Wear ANSI approved safety impact goggles when assembling this product. Goggles are available from Harbor Freight Tools. 5. DO NOT OVERREACH. Keep proper footing and balance at all times when assembling this product. The glass top of the table should be handled with care. It is recommended that two people assemble this product. 6. STAY ALERT. Watch what you are doing at all times. Use common sense. Do not assemble this product when you are tired or distracted from the job at hand. SKU 9246 For technical questions, please call Page 2

3 7. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect this product. Replace or repair damaged or worn parts immediately. 8. DO NOT STAND ON THE TABLE AND CHAIRS. Use this product for its intended purpose only. Injury could occur if table is overloaded or unbalanced. Use with caution! Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator. Unpacking When unpacking this product check to make sure that all parts are included as shown in the parts list. If any parts are missing or broken, please call Harbor Freight Tools at the number below. ASSEMBLY INSTRUCTIONS NOTE: All parts below refer to the parts listed on page 6 of this manual. Table Assembly:. Place the Table Top () upside down on a smooth clean surface. Slip one Leg (2) into the Leg Holder in the underside of the Table Top (). See Figure and 2 on the next page. Leg (2) Support Bracket () Bolt (4) Washer (5) Table Top () Leg Holder Wrench (0) Bolt (4) Washer 5) Figure SKU 9246 For technical questions, please call Page

4 Leg Holder Figure 2 2. With the Table Top () still upside down on the floor, place the other two Legs (2) into the Leg Holders with all three Legs coming together in the center of the Table. See Figures 2 &.. Slip the Support Bracket () between the three Legs (2). Match up the predrilled holes in the Support Bracket () and Legs (2). Secure each Leg (2) with a Washer (5), Lockwasher (6) and then the Bolt (4). Tighten the Bolt with the Wrench (0). After tightening, tap on a Cover (7) over each of the Bolt heads. See Figure. Leg (2) Support Bracket () Bolt (4) Cover (7) Figure SKU 9246 For technical questions, please call Page 4

5 4. Tap the Feet (8) onto each Leg (2). Turn the Table assembly over and test to be sure it is level. See Figure 4 & 5. Feet (8) Figure 4 Figure 5 5. Unfold the Chairs (9) by holding the top of the chair in one hand and pulling up on the seat of the chair with the other hand. Sit the chairs around the Table. See Figure Observe the weight capacity for the Top of Chair chairs and table to avoid tipping and breakage. Maintenance Chair Folded. For better and safer performance, keep all parts of this product clean and dry at all times. 2. Excess exposure to the sun and harsh weather could weaken the fiber in the seat and backs of the chairs. Fold chairs and store in a dry place during these conditions. See Figure 6. Seat of Chair. Clean the glass Table Top with glass cleaner. Dry thoroughly. Clean the seat and chair backs with a damp cloth. Dry thoroughly. Figure 6 SKU 9246 For technical questions, please call Page 5

6 Parts List Part # Description Qty Table Top Leg Support Bracket Bolt Washer Lock Washer Covers Feet Chair Wrench 2 Part Part 4 Part 5 Part 6 Part 7 Parts Identification Part Part 9 Part 9 Part 0 Part 8 Part 2 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACE- MENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. SKU 9246 For technical questions, please call Page 6