TABLE OF CONTENTS IN TR O DUCT I ON S AFETY & PRE CAUTIONS D R O NE DI AGRAM TRAN SMI T T E R DIAGRAM INSTALLING THE TRANSMITTER BATTERY

Transcription

1 ITEM NO

2 TABLE OF CONTENTS IN TR O DUCT I ON 3 S AFETY & PRE CAUTIONS 3 D R O NE DI AGRAM 4 TRAN SMI T T E R DIAGRAM 4 INSTALLING THE TRANSMITTER BATTERY 5 INSTALLING THE DRONE BATTERY 5 ATTACHING THE SMART PHONE CRADLE 5 ATTACHING THE SMART PHONE 5 CHARGING THE DRONE BATTERY 6 TRANSMITTER LCD INTERFACE 7 SYNCING THE DRONE TO THE TRANSMITTER 7 FLIGHT CONTROLS - AUTOPILOT:TAKE OFF/LANDING 7 FLIGHT CONTROLS 8 LIVE FEED CAMERA APP OPERATION 9 ATTACHING THE DRONE CAMERA 9 USING THE DRONE CAMERA 9 ADJUSTING THE TRIM 10 SPECIAL ACTIONS 11 LOW VOLTAGE ALARM PROTECTION 11 POST FLIGHT 12 REPLACING THE ROTORS 12 TROUBLESHOOTING 13 BATTERY DISP OSAL WARNINGS 13 NOTES: 14 2

3 INTRODUCTION Thank you for purchasing this amazing World Tech Toys product. This drone is designed for outdoor flight. Please carefully read the entire manual before operating this drone and keep it for reference in the future. SAFETY & PRECAUTIONS 1. Important Instructions 1) This product is not a toy. It is a precision piece of equipment with integrated mechanical technologies, electronic, aero dynamics and radio frequencies. To avoid accidents, the operator must read these instructions carefully, prior to operation. If operated incorrectly, serious physical injury and/or property loss may occur. 2) This product is suitable for operators with previous hobby flying experience, age 14 and up. 3) Only fly in a safe environment that is legal for remote control flying. 4) We are not responsible for the operation and control of this device and related safety responsibilities. 2. Safety Instructions 1) Always operate far away from obstacles and crowds. This drone has uncertain flying speeds and conditions which present potential danger. Fly away from people, animals, high buildings, high voltage wiring, etc. To ensure a safe and fun flying environment avoid bad weather conditions like wind, rain, and thunder. 2) Avoid high temperatures. This drone is made of metal, plastic, electronic components and other materials. Keep away from any heat source and avoid using in high temperatures to prevent transformation and broken parts resulting from the heat. 3. Flight Environment The inside of this drone is integrated with precision electronic and mechanical parts. Avoid contact with water and wet environments as it may result in parts breakdowns and accidents may occur. 3. Attention Before Flying 1) The minimum recommended flying area is 25ft x 25ft x 15ft. 2) Be sure that the transmitter and drone batteries are fully charged. 3) Be sure that the throttle is at its lowest position to avoid premature flight. 4) Always turn on the drone first, then turn on the transmitter. Incorrect operation may result in failure and the possible influencing of other devices in area. 5) Ensure that all plugs and wires are secure and in place as they may loosen over time. 3

4 DRONE DIAGRAM BOTTOM OF DRONE Battery Compartment Rotor Power Switch Landing Skids HD Picture/Video Camera Mount HD Picture/Video Camera LED Lights Landing Skids TRANSMITTER DIAGRAM Smart Phone Cradle Power Indicator Speed Control Auto Pilot Camera Fine Tuning Forward/Backward Trim Adjustment Rudder Throttle Left/Right Trim Adjustment Power Switch Camera Follow Me A Return Orbit Video GPS Switch *Speed Control Modes: Low Speed: Transmitter beeps once. High Speed: Transmitter beeps twice. NOTE: Drone starts in the Low Speed Mode. Press the HIGH SPEED GEAR button to toggle. 4

5 INSTALLING THE TRANSMITTER BATTERY First remove the battery cover by sliding down. Next install 4 AA batteries with the correct polarity. Finally replace the battery cover. CAUTION: Battery Cover 1. Make sure the batteries are installed with the correct polarity. 2. Do not mix old and new batteries. 3. Do not mix different types of batteries. 4 AA Batteries (NOT INCLUDED) ATTACHING THE SMART PHONE CRADLE ATTACHING THE SMART PHONE To attach smart device, pull up on the black handle on top of the cradle and insert device between foam protectors. Align the Smart Phone Cradle with the opening on top of the remote and slide in. INSTALLING THE DRONE BATTERY Battery Compartment Power Switch Make sure the power switch on the battery pack is in the OFF position and the drone is free of debris. Align the connectors of the battery pack to the drone, then slide the battery pack into the drone until a click is heard. 5

6 CHARGING THE DRONE BATTERY Make sure the drone power button is in the OFF position. Push down on the button on top of the battery pack, above the power button. Slide the battery out of the drone. To Computer USB Power Supply Plug the USB charger into any standard USB Power Adaptor or computer USB power supply. Your battery will automatically charge. Connect the included USB charger via the port shown on the battery pack. USB CHARGER LED LIGHT INDICATOR Green Light Charging Red Light Charger is connected to a power supply without the battery attached. Battery pack is fully charged. Please Note: The charger light will turn on when plugged in to indicate there is power running through the device. Once the battery is connected the light will turn green. The light will turn back to red when charging is complete. BATTERY PACK SPECIFICATIONS Battery Type Battery Specification Usage Duration Charge Time Lithium Polymer 7.4V 2000mAh Flight Duration minutes Charging Time minutes CAUTIO N W HI L E CH A R GIN G: Do not charge with batteries still installed. Do not charge battery unsupervised. Do not immediately charge after use. Do not overcharge battery. Ideal charge time is minutes. Overcharging can cause a catastrophic failure. Always charge on dry and ventilated areas away from any heat source or flammable materials. Always use the original charger provided. Promptly change and replace old or defective batteries. 6

7 SYNCING THE DRONE TO THE TRANSMITTER Switch ON the drone and place it on a flat surface. The drone s LED lights will start flashing. Switch ON the transmitter and position the Ascend/Descend joystick (left joystick) straight down. The transmitter will emit 2 short beeps and the drone s LED lights will stop flashing. The signal icon will appear on the top left of the LCD screen indicating there is no signal. The power indicator will flash for approximately 5 seconds. After the transmitter successfully pairs with the drone, the signal icon will change to. The transmitter has successfully paired with the drone and control information will now appear on the LCD screen. TRANSMITTER LCD INTERFACE Signal Icon GPS Display Battery Level Camera Indicator Forward/Backward Trim Display Speed Mode (Low/High) Height/Distance Display Speedometer FLIGHT CONTROLS - AUTOPILOT: TAKE OFF/LANDING Before flying the drone for the first time please read the instructions carefully and make sure you fully understand how to control your drone. AUTO PILOT AUTOMATIC TAKE OFF Once you ve gone through the flight preparation, press the AUTO PILOT button once and the drone s rotors will start to spin. You can now slowly press up on the Ascend/Descend stick (left joystick) and the drone will take off. YOU MUST PRESS THE A KEY OFF BUTTON TO START THE ROTORS SPINNING. YOU WILL NOT BE ABLE TO TAKE OFF UNTIL YOU PRESS THIS BUTTON. AUTO PILOT AUTOMATIC LANDING When you are ready to land, press the AUTO PILOT button and the drone will slowly descend and land from an elevation of approximately 2 meters. Pressing again will cancel the operation. 7

8 FLIGHT CONTROLS Ascend/Descend Move Forward/Backward Move Left/Right FRONT Move Left Move Right BACK Turn Left Turn Left/Right FRONT Turn Right BACK 8

9 LIVE FEED CAMERA APP OPERATION Scan the corresponding QR code to download the application intended for you device. You can also download via the App Store, Google Play, or Search your phones application store for ECHO FPV and download the free app. This application allows you to see a live feed of your drones camera and take photos/videos that can be kept in the app or saved to your phone. Return Record Take Photo 2. Turn on the drone, go into the WI-Fi settings of your phone and select the network WIFIUFO-XXX (X s are the unique ID of your drone) to establish a connection. This must be done every time the drone is first turned on. Speed Gallery Gravity Atmospheric Pressure Reverse Picture Toggle Controls 3D Mode Fly forward Speed up 3. Open the ECHO FPV app and select PLAY to go to live feed screen shown to the right. Start flying and use touch controls to take photos or start and stop recording. Select Gallery to view/delete photos and videos in app. Copies are automatically saved to your phones media viewer. Additional info available in Help section on app. * NOTE: Some features listed may not be available for your device. Turn Left Turn Right Reset Gyro Stop 360 Flip Pitch Fine Tune Fly to the right Fly to the left Speed down Fly backwards Yaw Fine Tune Roll Fine Tune ATTACHING THE DRONE CAMERA Make sure the drone power switch is in the OFF position. Slide the camera onto the bracket on the bottom of the drone. Once camera is secured in the bracket, connect the three prong cord and the mini USB to the drone. USING THE DRONE CAMERA Make sure the both the drone and transmitter are turned on, and the transmitter is synced with the drone. Taking a Photo: Press the PHOTO button once on the transmitter. The camera indicator light located inside the camera will flash RED once when a photo is taken. Recording Video: Press the VIDEO button once on the transmitter. The camera indicator light located inside the camera will start flashing RED when recording video. Press the VIDEO button again to stop recording video. NOTE: YOU CAN NOT TAKE A PHOTO WHILE RECORDING VIDEO. The drone comes equipped with a 1 axis camera gimbal, and the camera angle can be adjusted using the CAMERA FINE-TUNING switch located next to the ASCEND/DESCEND joystick. CAMERA FINE-TUNING: Slide to adjust the lens angle forward and backwards. 9

10 ADJUSTING THE TRIM When the drone moves without transmitter input, adjust the trim controls until hovering is stable. Push the RIGHT TRIM button until the drone stops turning. Drone is turning to the left. Turn Right Trim Push the LEFT TRIM button until the drone stops turning. Drone is turning to the right. Turn Left Trim FRONT Push the BACKWARD TRIM button until the drone stops. Drone is moving forward. BACK Backward Trim FRONT Push the FORWARD TRIM button until the drone stops. Drone is moving backward. BACK Forward Trim FRONT Push the MOVE RIGHT TRIM button until the drone stops. Drone is moving to the left. BACK Move Right Trim FRONT Push the MOVE LEFT TRIM button until the drone stops. Drone is moving to the right. BACK Move Left Trim 10

11 SPECIAL ACTIONS FOLLOW ME You can set your drone to follow a consistent flight path by pushing the FOLLOW ME button. The drone will automatically fly to an altitude of 3 meters, stabilize and maintain its flight path in relation to the remote control. FOLLOW ME In FOLLOW ME mode, the drone will realign itself to follow the direction of the remote control. The drone will adjust to correspond with the trajectory of the remote. It will maintain the same distance and move relative to the transmitter. Be sure to always be aware of your surroundings. Check to make sure there are no obstacles in the drone s or pilot s path when engaged in FOLLOW ME. To disengage FOLLOW ME, simply press the FOLLOW ME button again and resume normal control of the drone. ORBIT The drone can circle the location of the remote automatically. Press the POINT OF INTEREST button and the drone will automatically rise to an altitude of 3 meters and fly a clockwise flight path around the area of the remote. GPS RETURN Engages a simple return of the drone to the GPS location of the remote transmitter. Press the GPS SWITCH to activate. LOW VOLTAGE ALARM PROTECTION For safety precautions, the drone will automatically notify the operator in the event of a low voltage occurrence that causes the signal from the remote to be interrupted. 1. When the battery voltage reaches the range of 6.5V-7.1V, the low voltage alarm will trigger and the front and rear lights on the drone will flash. 2. The Power Indicator Light located on the remote will flash. 3. Once the drone enters this mode, safe flight time is approximately 2-3 minutes. Operator should make any adjustments to the flight path in order to ensure a safe landing. 4. After the drone is safely landed and powered down, make sure to replace the batteries as needed before operating again. 11 Power indicator

12 POST FLIGHT After you are done flying the drone make sure the battery pack is disconnected and the transmitter power is turned off. If you are not going to use the drone for a long period of time, please remove the AA batteries from the transmitter to prevent them from draining or leaking. REPLACING THE ROTORS The rotors may become damaged during a collision. The drone comes with 4 spare rotors. Please replace damaged rotors immediately. The drone comes with 2 A rotors and 2 B rotors. The A and B rotors must be installed on specific locations on the drone for it to fly properly. Check the bottom of each rotor to see if it s labeled either A or B. Use the illustration to the right to install them in the correct location. Remove the decorative cap on the propeller by turning in a counterclockwise motion. A B FRONT BACK B A Remove the damaged rotor by lifting upward. Be sure not to misplace the cap. Place the correct A or B rotor on top of the peg. 12 Replace the cap on the rotor. Repeat the process for any other rotors that need replacing.

13 TROUBLESHOOTING PROBLEM CAUSE SOLUTION Drone is unresponsive. The transmitter light keeps flashing. Transmitter is not syncing with drone. Repeat the power up process. Drone is unresponsive. Transmitter and or drone is not powered ON. Transmitter batteries are installed incorrectly. Turn both transmitter and drone ON. Transmitter batteries are drained. Install fresh batteries in the transmitter. Drone s battery pack is drained. Charge the drone s battery pack. Autopilot isn t activated. Press the Autopilot button once and the rotors will start spinning. You will now be able to take off. Rotors are damaged. Replace the damaged rotors. Both drone and transmitter are ON. Drone is unresponsive. Drone s rotors spins but doesn t take off. Install the batteries with the correct polarity. Drone s battery pack is drained. Charge the drone s battery pack. Drone is not on a flat surface. Place the drone on a flat surface before attempting to take off. Drone is shaking when flying. Rotors are damaged. Replace the damaged rotors. Drone moves while hovering without transmitter input. Trim needs to be adjusted. Adjust the trim. Drone still moves forward after adjusting the trim. Gyroscope midpoint is off. Turn off both transmitter and drone. Go through power on process and make sure you place the drone on a flat surface before taking off. BATTERY DISPOSAL WARNINGS The battery lifespan is estimated to be approximately 300 charges. After this, it is recommended to replace the battery. Please follow all local, state and federal laws when disposing of electronics and electronic waste. It is recommended that the battery be fully discharged before discarding. If you plan to store your drone for an extended period of time, it is recommended to discharge the battery to at least 50% capacity before storing. Charging the stored battery once every three months will help maintain the battery life and ensure that a charge can be held. Should the battery expand or become physically damaged, it is recommended to stop using immediately and replace the battery. Continued use of a damaged battery could result in fire, explosion or other hazards. 13

14 NOTES: Website: Phone: (877) Monday - Friday / 8:00AM - 5:00PM / Pacific Time SPECIFICATIONS, COLORS AND CONTENT MAY VARY FROM ILLUSTRATIONS MADE IN CHINA 14