Altro Screed 5mm Rapicure standard, Altro Screed 5mm Rapicure slip-resistant
|
|
- Patience Quinn
- 6 years ago
- Views:
Transcription
1 Atro Screed 5mm Rapicure standard, Atro Screed 5mm Rapicure sip-resistant Sovent-free ow odour, rapid cure, epoxy screed Technica and instaation data sheet September 2016 Product description FeRFA 6 Atro Screed 5mm Rapicure is a fast cure, ow odour decorative epoxy resin system, comprising cear resin and cooured graded aggregates. Atro Screed provides a moderate eve of chemica and impact resistance. It is suitabe for use in medium to heavy duty areas. For areas where there is risk of a sip the Atro Screed 5mm Rapicure sip-resistant variant shoud be used. Atro Screed Rapicure standard sea coat is a cear soventfree epoxy, which reduces cure-times and provides a more rapid acquisition of resistance to spiage for an enhanced return-to-service time. Atro Screed Rapicure sip-resistant sea coat is a cear sovent-free epoxy, which offers the performance of Atro Screed Rapicure standard sea coat, with the added benefit of enhanced sip-resistance for areas where there is an increased risk of a sip*. Standard coours Atro Screed 5mm Rapicure variants are avaiabe in 39 standard coours. Bespoke coour systems require a minimum ead time and acceptance of a sampe. Advantages Fast return-to-service Sip-resistant surface variant Coveabe impervious finish Ease of ceaning Exceent water marking and chemica resistance Moderate impact and abrasion resistance Provides seamess foor finish (substrate joints must be cut through) Sustainabiity Atro s steps to sustainabiity program seeks to optimise our performance with respect to the panet s resources. Pease refer to for further information. Packaging Atro Screed 5mm Rapicure is avaiabe in a 23kg three part composite pack. Atro Screed Rapicure standard sea coat is avaiabe in a 2.3kg two part composite pack. Atro Screed Rapicure sip-resistant sea coat is avaiabe in a 3kg three part composite pack. Typica areas of use Circuation areas Laboratories Custodia areas Warehouses Pharmaceutica Canteens* CDT* Changing areas*
2 Chemica resistance AtroScreed 5mm Rapicure offers resistance to a range of commony used chemicas. However, premature or proonged contact with chemicas (incuding water during curing) may give rise to discoouration, staining and variation in goss. In a cases of chemica spiage, it is essentia that the spiage be immediatey removed and the surface washed down with cean water, removing water by wet vacuum after operation. Athough some chemicas may cause discoouration, this may not affect the durabiity and integrity of the resin screed. Pease refer to Atro and FeRFA Guidance Note No.3 for further information. Typica physica properties Atro Screed 5mm Rapicure Atro Screed Rapicure standard sea coat Atro Screed Rapicure sip-resistant sea coat Sip resistance DIN Shoes / oi BS 7976 Penduum test vaue (wet)-sider 96 Dependent on sea coat R9 R10 Dependent on sea coat Moderate potentia for sip 36 Low potentia for sip 40 Speed of cure 6-8 >20 C 6-8 hours >20 C 6-8 hours >20 C Over-coating time Light traffic 6-8 >20 C 24 hours > 20 C 48 hours >12 C 24 hours > 20 C 48 hours >12 C Working time C C C Return to service 3 > 20 C 5 12 C 3 > 20 C 5 12 C Atro Screed sip-resistant sea coats are not suitabe for use in bare foot shower areas. Coverage Atro Prime fast track 24m² per 5kg unit Atro Screed 5mm Rapicure 2.25m² / 23kg 5mm Atro Screed Rapicure standard sea coat 1st coat 9m² per 2.3kg unit 2nd coat 18m² per 2.3kg unit Atro Screed Rapicure sip-resistant sea coat 1st coat 7.5m² per 3kg unit 2nd coat 30m² per 3kg unit Atro Sea water-based matt Singe coat 100m² per 5kg unit Materia usage is dependent upon temperature, surface profie and porosity; stated coverage rates shoud be referred to for guidance ony and cannot be reied upon to determine exact quantities. Storage Ensure that the product is received in good order and store in a dry, frost-free environment, ideay between 15 C and 20 C for at east three days before aying. Excessivey high and ow storage temperatures wi affect the aying performance of the product. Suitabe substrates Atro Screed 5mm Rapicure may be appied to a variety of substrates incuding, but not imited to, concrete, poymer modified cementitious screeds, terrazzo, 25mm marine grade pywood (consut Atro for further guidance). For a proprietary subfoor systems refer to the manufacturer for recommendations and seek further guidance from Atro. FeRFA, The Resin Fooring Association, does not recommend Cacium Suphate, Anhydrite or Hemi-hydrite screeds for overayment with synthetic resin surfaces. Athough stringent quaity assurance processes are empoyed, when coour consistency is required, a singe batch shoud be used. We cannot guarantee batch matches between different batches of aggregate. Necessary transitions between batches shoud be panned for non-conspicuous areas. Dark cooured Atro Screed variants wi highight any defects such as roer ines and scratches.
3 Substrate requirements Substrates shoud be dry, structuray sound and free from contamination, friabe materias or aitance which may affect either the adhesion or penetration of the resin system. A residues of od paint coatings and dust must be removed. Substrates to achieve 26N/mm 2 compressive strength (BS EN ) and surface tensie strength 1.5N/mm² (BS EN ). Substrates must incude an effective damp proof membrane and contain residua moisture not greater than 5% by weight (75% R.H.) to BS Thin-bed synthetic resin systems foow the surface of the substrate, so it is essentia that the surface reguarity of fatness conforms to or exceeds BS cass SR2 (+/- 5mm under a 2 metre straight edge). Any deviation from this may require a surface improver to be appied which must be suitabe to receive an epoxy resin overay. Pease consut Atro or FeRFA Guide to the Specification and Appication of Synthetic Resin Fooring for further information. Substrate preparation Surface preparation is the most vita aspect of resin fooring appication. Inadequate preparation wi ead to oss of adhesion and faiure. The substrate in question wi dictate the method of preparation. In the case of a concrete foor, preparation by dust encosed diamond foor grinder may be appropriate, or if of a sufficient area for economic reasons, shoud be ighty shot basted to eave a textured surface free from contamination. If the foor has been treated with a cementitious surface improver, then the surface shoud be prepared in accordance with the manufacturer s recommendations, or abraded with an STR machine foowed by thorough vacuuming. Treatment of oca repairs such as cracks and hoes, improvement or modification of eves and remova of high spots, shoud be undertaken prior to the fooring instaation. Pease consut Atro or FeRFA s Guide to the Specification and Appication of Synthetic Resin Fooring for further guidance. Panning Before proceeding with the instaation, carefu consideration shoud determine the best way of instaing the Atro system. Efforts shoud be made to minimise day joints and optimise the open time of the product (i.e. minimise the distance between mixing and aying). It is best to aso consider the effect of externa infuences on the fina instaation (i.e. direction of ight from windows etc.). Time spent at this stage wi be invauabe towards the success of your instaation. The Atro Screed foor system is designed to be aid at a minimum of 5mm. Atro recommends that stainess stee mixing, aying and appication toos are used in this process. Meta transfer from mid stee toos may resut in discoouration of the screed which wi be unacceptabe to your customer. This wi be particuary noticeabe with pae coours, pease contact Atro for further guidance. Appication The foowing appication guide is based on aboratory and simuated site conditions. However, when instaations conditions differ appreciaby from those detaied by Atro, the performance characteristics of both mixing and aying may not be as expected. To achieve the best resuts at a times pease endeavour to estabish the correct conditions which in turn wi aow the materias to be aid effectivey, and meet your customer s expectations. Instaation conditions Appy in we ventiated areas. Both the sab and air temperature shoud be greater than 10 C and rising, up to 25 C. It is not advisabe to mix and ay epoxy resin products outside the range 10 C to 25 C. Ambient conditions shoud be maintained at east 3 C above dew point or beow 75% R.H. during the first 24 hours of cure. At site temperatures beow 10 C cure times wi be substantiay increased uness some form of externa heating is used. It must be recognised that the concrete sab temperature wi generay be ower than the air temperature, often as much as 10 C, and this wi govern the rate of cure. As the resin fooring cures, in condensing conditions moisture vapour may condense onto the surface and cause booming, a permanent couding of the surface. Mixing equipment Sow speed dri ( rpm), such as MM17 * Mixing padde, such as MR2 60B * Forced action mixer (stainess bades), such as RM65 * Stainess mixing vesse, such as RM65 drum * * A too number references reate to Refina Ltd Priming the substrate In order to achieve a uniform finish, prevent bubbes and maximise substrate adhesion, primer must be used. An Atro primer shoud be seected that is suited to the instaation and appropriate for the nature and moisture content of the substrate (seek further guidance from Atro). The appropriate Atro primer shoud be appied in accordance with the product data sheet. Whist the primer is wet, ighty seed with a sharp, medium size kin-dried aggregate (preferaby 0.7 to 1.2mm quartz in a coour to match the Atro Screed and eave to cure. Ensure that the primer provides a pore free continuous coat to fuy sea the substrate. Ensure that a hungry areas are addressed before proceeding to insta the system. If the overcoating time period for the primer is exceeded, the surface shoud be ighty abraded and vacuumed before further coats are appied.
4 Product instaation Remember to aways use the correct PPE. Using a sow speed dri and padde thoroughy mix together the base and hardener. Pour a the mixed base and hardener contents into a suitabe cean poypropyene or stainess stee mixing vesse. The aggregate shoud be added graduay into the pre-mixed binder, whist continuing the mixing action, and mix for a further 2-3 minutes in the forced action mixer. A singe padde Danes type mixer is unsuitabe for use with this product. Excessivey vigorous mixing shoud be avoided as this can ead to undesirabe air entrainment. Care shoud be taken to ensure that any materia adhering to the sides, bottom and corners of the mixer is thoroughy bended in. If the mixing area is not adjacent to the aying area the time required to transfer the mixed materia wi reduce the open instaation time. Using a cean stainess stee trowe or sedge appy the Atro Screed to the prepared primed substrate. Ensure that the system is being aid to the desired depth and fuy cosed off to eave a uniform compact surface. Because the fooring is hand finished, there may be sight variations in surface appearance resuting from the troweing. A skied operative wi endeavour to keep these to a minimum so that the overa appearance and performance of the fooring wi not be affected. Aow the Atro Screed to cure. The system must be seaed with two coats of Atro Screed sea. Ensure the surface of the resin screed is contamination-free and has been de-nibbed and thoroughy vacuumed as necessary. Aways use site overshoes to protect the screed. Atro Screed Rapicure standard sea coat Pour the contents of the hardener into the base unit, and using a sow speed dri and padde thoroughy mix the contents for two minutes. To ensure thorough mixing pour the materias into another container and mix again for a further minute. Ineffective mixing can ead to yeow staining in the sea coat. Appy the sea coat to the screed using a dense poypropyene foam squeegee, taking time to work the sea into the surface, ensuring that a porous areas of screed are fuy satisfied. Ro the surface with a short nap synthetic roer and eave to cure for not onger than 18 hours at 20 C. Mix and roer appy the finishing sea coat grouting into the screed using a dense poypropyene foam squeegee and ro the surface as before to eave a uniform cosed fim across the foor where a excess is removed. Faiure to remove excess may affect the sip resistance and appearance of the finished system. Do not food sea the Atro Screed as this can cause staining or discoouration, in the sea system. Atro Screed Rapicure sip-resistant sea coat Pour the contents of the hardener into the base unit and using a sow speed dri and padde thoroughy mix the contents for two minutes. To ensure thorough mixing pour the materias into another container and mix again for a further minute. Ineffective mixing can ead to yeow staining in the sea coat. Add the aggregate component. Mix for another minute unti uniform. Using a grouting foat, grout the Atro Screed sipresistant sea coat into the surface of the Atro Screed. Ensure that a porous areas of quartz are fuy satisfied. Remove any excess materia buid-up on the surface. Pre-wet a short pie poyester or nyon roer. Back roer the surface to form an even continuous coating. Leave to cure for not onger than 18 hours at 20 C. Mix and appy a tight second coat as above to eave an even cosed fim across the foor. Aways observe the coverage rates to ensure an even sip resistance of the finished system. Do not food sea the Atro Screed as this can cause staining or discoouration, in the sea system. Atro Sea water-based matt To achieve a cosmetic matt finish, the appication of a singe coat of Atro Sea water-based matt can be appied not more than 24 hours at 20 C foowing the fina sea. Pour the contents of the hardener into the base unit, and thoroughy mix using a sow speed dri and padde for two minutes making sure to incorporate a the matting agent in the base. Appy a very thin coat using a short nap synthetic roer appying the product to the foor from a paint tray. Heavy appication of this sea wi resut in an opaque appearance of the finished foor, therefore care is required in its appication. Ensure good air-fow and ventiation to assist with cure. Enough time shoud be given to aow the Atro Sea waterbased matt to reach its fu chemica cure. Physica drying of the surface aone is not indicative of the fu cure properties incuding wear and chemica resistance. Joints The spacing of movement joints must be determined by the design of the subfoor. A ive movement joints in the subfoor must be continued through the resin fooring, faiure to do so wi resut in ive cracks being refected through the resin finish. In a instances the type and positioning of movement joints shoud be agreed at the design stage between a parties concerned. Pease refer to Atro or FeRFA s Guide to the Specification and Appication of Synthetic Resin Systems for further guidance. A joints shoud be fied with Atro Expand fexibe jointing compound. Pease see Atro Expand data sheet for further information.
5 Protection Whist of an extremey durabe nature these foor systems must be thoroughy protected from the rigours and abuse that exist during the on-going contractua works. The resin foor shoud be ready for fu service in 3-4 days at 20 C. Untreated fet paper wi suffice as protection from ight traffic, however if protection is required from other trades then the foowing protection option shoud be considered. Where heavier access is required then a more suitabe medium to take the oadings, such as shuttering py or Correx by Cordek, shoud be paced on top of the untreated fet paper. The resin system shoud have cured for at east 24 hours prior to pacing the protection. No poyethyene sheets, inseed-treated hardboard, print or dyed card shoud be paced in contact with the resin surface. A joints in the protection medium shoud be taped, and a accidenta spiages shoud be recovered immediatey by remova and reinstatement of the protection. Damage wi occur to the system if the above guidance is not foowed. Ceaning (during instaation) A toos and equipment shoud be reguary ceaned using Atro Sove EP to reduce buid up and maintain the quaity of the instaation. Avoid contamination of the resin surface with sovent as this may cause ocaised boom to occur. Ensure that the correct PPE is worn at a times. Disposa Due diigence must be adopted if accidenta spiages occur. Recover using inert absorbent granues, transferring into a suitaby marked container. Disposa of a empty containers and accidenta spiages shoud be in accordance with the oca waste disposa authority. Ceaning guidance Optimum sip resistance and appearance can ony be maintained with reguar ceaning. The texture of the surface wi require mechanised ceaning; mop ceaning wi not be effective. Steam ceaners and / or hot pressure ceaners shoud not be used on the foor or was. A cod / ambient pressure washer may be used if required, but the pressure shoud not exceed 1400psi. Warm water wi offer improved ceaning, but the water temperature shoud not exceed 60 C Sweep or vacuum the foor to remove debris For norma ceaning, diute an akaine detergent such, as Atro Cean 44 or simiar, by 1:40 in cean water Aternativey, diute by 1:10 for infrequent heavy ceaning Liberay appy the water and detergent soution to the foor, scrubbing with a deck scrubber or sow-speed (< 400rpm) scrubbing machine and Atro UniPad or simiar Pay particuar attention to areas where residues may accumuate, such as interna corners of perimeter coves and around coumns etc If possibe, aow the detergent soution to remain on the foor for severa minutes to break down deposits, but not sufficienty ong to aow the soution to evaporate Remove the soution by wet vacuum recovery and foow this with a fresh water rinse, or rinse the soution into drains if permissibe It is important that a detergent residue is removed from the textured surface of the foor. Detergent may become sippery which affects safety, or sticky which attracts and hods more dirt Pease refer to materia safety data sheets prior to instaation. Aways wear correct PPE whist instaing Atro products. To order E-mai ResinSaesDesk@atro.com Ca Fax NOTE: Atro Ltd ( Atro ) endeavours to ensure that advice and information given in Product Data Sheets, Method Statements and Materia Safety Data Sheets (a known as Product Literature) is accurate and correct. However, where Atro has no contro over the seection of its products for particuar appications, it is important that any prospective customer, user or specifier, satisfies him / hersef that the product is suitabe for the intended appication. In this process, due regard shoud be taken of the nature and composition of the background / base and the ambient conditions both at the time of aying / appying / instaing / curing of the materia and when the competed work is to be brought into use. However, as site conditions and the execution of the work are beyond our contro, we accept no resutant iabiity. Atro s poicy is one of continuous research and deveopment and we reserve the right to update our products and information at any time without prior notice. Entrance matting wi reduce ceaning requirements and shoud aso enhance the ongevity of the foor, when combined with correct maintenance. If you d ike any more information or guidance pease get in touch, we re here to hep. te: fax: emai: enquiries@atro.com or expore
Altro Seal standard, Altro Seal slip-resistant and Altro Seal vertical
Atro Sea standard, Atro Sea sip-resistant and Atro Sea vertica UV stabe poyurethane foor coating Nomina thickness 180 microns Technica and instaation data sheet September 2016 Product description FeRFA
More informationAltro Grip 6mm slip-resistant
Atro Grip 6mm sip-resistant Sovent-free, epoxy finish Technica and instaation data sheet September 2016 Product description FeRFA type 4 Atro Grip 6mm sip-resistant variant is a muti-ayer epoxy resin system
More informationAltro Screed 3mm standard and Altro Screed 3mm
Atro Screed 3mm standard, Atro Screed 3mm sip-resistant Sovent-free, decorative, epoxy screed Technica and instaation data sheet September 2016 Product description FeRFA N/A Atro Screed 3mm standard and
More informationAltro Tect standard, Altro Tect slip-resistant, Altro Tect vertical, Altro Tect fast-track,
Atro Tect standard, Atro Tect sip-resistant, Atro Tect vertica, Atro Tect fast-track, Sovent-Free epoxy coating Nomina thickness 400-500 microns Technica and instaation data sheet Juy 2017 Product description
More informationAltro Mosaic standard matt, Altro Mosaic standard gloss, Altro Mosaic vertical matt and Altro Mosaic vertical gloss
Atro Mosaic standard matt, Atro Mosaic standard goss, Atro Mosaic vertica matt and Atro Mosaic vertica goss Muti-coour decorative foor finish system Nomina thickness 1-1.5mm Technica and instaation data
More informationAltro Flow 1mm standard, Altro Flow 2mm standard and Altro Flow 3mm standard
Atro Fow 1mm standard, Atro Fow 2mm standard and Atro Fow 3mm standard January 2019 Sef-smoothing epoxy fooring Technica and instaation data sheet Product description FeRFA type 5 Atro Fow 1mm standard,
More informationAltro Coat standard, Altro Coat slip-resistant,
Atro Coat standard, Atro Coat sip-resistant, Atro Coat vertica Water dispersed epoxy coating Nomina thickness 180 microns Technica and instaation data sheet September 2016 Product description FeRFA type
More informationAltro Crete 2mm slip-resistant, Altro Crete 4mm slip-resistant (PTV 36)
Atro Crete 2mm sip-resistant, Atro Crete 4mm sip-resistant (PTV 36) January 2019 Sef-smoothing poyurethane fooring Technica and instaation data sheet Product description FeRFA type 4 Atro Crete 2mm sip-resistant
More informationAltro Screed 4mm standard, Altro Screed 4mm slip-resistant
Atro Screed 4mm standard, Atro Screed 4mm sip-resistant Sovent-free, decorative, epoxy screed Technica and instaation data sheet September 2016 Product description FeRFA 6 Atro Screed 4mm is a three-part
More informationUniversal one coat DPM Nominal thickness 250 microns Technical and installation data sheet. Product description. Standard colours
Atro Proof standard Universa one coat DPM Nomina thickness 250 microns Technica and instaation data sheet October 2016 Product description Atro Proof standard variant is a singe coat, high-buid epoxy surface
More informationAltro Flexiflow 2mm classic standard, Altro Flexiflow 2mm classic slip-resistant
Atro Fexifow 2mm cassic standard, Atro Fexifow 2mm cassic sip-resistant February 2018 PU sef-smoothing fexibe fooring Technica and instaation data sheet Product description FeRFA type 5 Atro Fexifow cassic
More informationAltro Flexiflow 8mm acoustic standard, Altro Flexiflow 8mm acoustic slip-resistant
Atro Fexifow 8mm acoustic standard, Atro Fexifow 8mm acoustic sip-resistant March 2018 Sef smoothing fexibe comfort fooring Technica and instaation data sheet Product description FeRFA type 5 Atro Fexifow
More informationAltro Pol. Additive for increasing strength of cementitious systems Technical and installation data sheet. Typical applications. Product description
Atro Po Additive for increasing strength of cementitious systems Technica and instaation data sheet November 2016 Product description Atro Po is a compementary part of the Atro fooring package, faciitating
More informationAltro Multiscreed TM EP Naturals
Altro Multiscreed TM EP Naturals 4mm Solvent-Free Epoxy Screed NOVEMBER 2010 Product Description FeRFA Type 6 Altro Multiscreed EP Naturals is a three-part solvent-free epoxy resin system with a natural
More informationAltroCrete PU Excel TM HF
AltroCrete PU Excel TM HF Heavy Duty Polyurethane Floor Screed Nominal thickness 5-8mm Technical and installation data SEPTEMBER 2012 Product Description FeRFA Type 8 As part of the Altro PU Excel range
More informationRESIN FLOORING. To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING
M12 To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING 110A - Primer reference: None or Altro Prime standard dependant on substrate - Resin flooring reference: Altro Grip 1mm slip-resistant
More informationTAYLOR ROSE. Design Project Management Construction. The High Care Project Specialists
TAYLOR ROSE The High Care Project Speciaists Design Project Management Construction www.tayorroseuk.co.uk Contents Introduction What We Can Offer Services Civi & Structura Works Fooring & Drainage Mechanica
More informationK10 FM Soffit Board. Insulation INSULATION FOR STRUCTURAL CEILINGS (SOFFITS) Higher R value per inch than any commonly used insulation
Insuation First Revision March 2017 K10 FM Soffit Board INSULATION FOR STRUCTURAL CEILINGS (SOFFITS) Premium performance rigid thermoset insuation R vaue of 16.5 on 2 in Higher R vaue per inch than any
More informationK10 FM Soffit Board. Insulation INSULATION FOR STRUCTURAL CEILINGS (SOFFITS) Higher R value per inch than any commonly used insulation
Insuation Third Revision June 2018 K10 FM Soffit Board INSULATION FOR STRUCTURAL CEILINGS (SOFFITS) Premium performance rigid thermoset insuation R vaue of 16.5 on 2 in Higher R vaue per inch than any
More informationSingle Ply Roofing System
Insua t i o n Second Revision Juy 2018 Singe Py Roofing System NEXT GENERATION INSULATION SOLUTION FOR FLAT ROOFS Optimum performance rigid vacuum insuation pane Insuating performance up to five times
More informationHEMPADUR MULTI-STRENGTH GF 35870
because prevention is better than cure Tough, tougher Product description is an amine cured pure epoxy coating reinforced with a high content of speciay seected amear gass fakes. The product provides exceent
More informationUniclass L68111:L35 CI/SfB EPIC F811:C21 (28.9) R (K3) Agrement Certificate No 90/2500. Promat MASTERBOARD. The Versatile Board
Unicass L68111:L35 CI/SfB EPIC F811:C21 (28.9) R (K3) Agrement Certificate No 90/2500 Promat MASTERBOARD The Versatie Board Promat MASTERBOARD Introduction Promat MASTERBOARD is a versatie Cass 0 buiding
More informationHammer-Capsule Hammer-Capsule 57.1 Introduction Hammer Capsule Specifications Product Description
Hammer-Capsue 57.0 Hammer-Capsue 57.1 Introduction The Hammer-Capsue System consists of a sef contained, singe use, two-part gass capsue into which threaded anchor rod or reinforcing bars can be directy
More informationSikafloor -264 is a two part, economic, solvent-free coloured epoxy resin, suitable for use under hot climate condition.
Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -264 2-part epoxy roller and seal coat Construction Product Description Sikafloor -264 is a two part, economic, solvent-free coloured
More informationK12 Framing Board. Insula t i o n INSULATION FOR WOOD AND STEEL FRAMING SYSTEMS. Premium performance rigid thermoset insulation. R value of 16 on 2
Insua t i o n First Issue Apri 2017 K12 INSULATION FOR WOOD AND STEEL FRAMING SYSTEMS Premium performance rigid thermoset insuation R vaue of 16 on 2 Higher R vaue per inch than any commony used insuation
More informationK20 Concrete Sandwich Board
Insuation Third Revision November 2017 K20 Concrete Sandwich Board HIGH PERFORMANCE INSULATION FOR CONCRETE SANDWICH WALL SYSTEMS Premium performance rigid thermoset insuation R vaue of 17 on 2 in Higher
More informationK20 Concrete Sandwich Board
Insuation Fourth Revision June 2018 K20 Concrete Sandwich Board HIGH PERFORMANCE INSULATION FOR CONCRETE SANDWICH WALL SYSTEMS Premium performance rigid thermoset insuation R vaue of 17 on 2 in Higher
More information2-part self smoothing epoxy coating, highly chemically and mechanically resistant
Product Data Sheet Edition 01/01/2014 Identification no: 02 08 01 02 019 0 000010 Sikafloor -381 2-part self smoothing epoxy coating, highly chemically and mechanically resistant Construction Product Description
More information2-part PUR tough-elastic coloured seal coat
Product Data Sheet Edition 22/02/2012 Identification no: 02 08 01 04 025 0 000001 Sikafloor -359 N 2-part PUR tough-elastic coloured seal coat Construction Product Description Sikafloor -359 N is a two
More informationConstruction. 2-part epoxy primer. Product Data
Construction Product Data Sheet Edition 2 May 2013 Sikafloor -161 2-part epoxy primer Product Description Sikafloor -161 is an economic, two part, low viscosity epoxy resin for the use where substrate
More informationAppearance /Colours Resin - part A: transparent, liquid Hardener - part B: transparent, liquid Packaging. Pre-proportioned 5.
Product Data Sheet Edition 30/08/2012 Sikafloor -160 2-part solvent free epoxy primer & binder, modular Sikafloor system Construction Product Description Sikafloor -160 is a two part, low viscosity epoxy
More informationPRODUCT DATA SHEET Sikafloor -378
PRODUCT DATA SHEET 2-PART TOUGH-FLEXIBLE COLOURED EPOXY SEAL COAT DESCRIPTION is a two part tough-flexible, coloured,epoxy seal coat with improved resistance against amine blushing under critical weather
More informationFlooring and Bedding. RonaFloor SL. Self-smoothing seamless epoxy resin flooring system
FEATURES self smoothing epoxy floor screed seamless high strength decorative good chemical resistance easy to clean can be applied to green concrete with use of RonaFloor Epoxy DPM Description RonaFloor
More informationSikafloor -161 is an economic, two part, solvent free, low viscosity epoxy resin, suitable for use under hot climate condition.
Product Data Sheet Edition 05.08 Identification no: Provisional Sikafloor -161 2-part epoxy primer, levelling mortar, intermediate layer and mortar screed Construction Product Description Sikafloor -161
More informationCOMPOSITE FLOORS - II
24 COMPOSITE FLOORS - II 1.0 INTRODUCTION This chapter describes the basis for design of composite foors using profied deck sheets adopting the equations described in the chapter on composite foors - I
More information2-part water based epoxy coating. Sikafloor W is a two part, water dispersed, solvent free, coloured, epoxy resin based coating.
Product Data Sheet Edition 11.2006 Version no. 09.06 Sikafloor -2530 W 2-part water based epoxy coating Construction Product Description Sikafloor -2530 W is a two part, water dispersed, solvent free,
More informationConstruction. 2-part epoxy roller and seal coat. Product Description. Product Data. Form. Storage. Product Data Sheet Edition _1
Construction Product Data Sheet Edition 2015-12_1 2-part epoxy roller and seal coat Product Description is a two part, economic, solvent-free coloured epoxy resin. Uses Roller coat for concrete and cement
More informationRESIN FLOORING. To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING
M12 RESIN FLOORING To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING 110A RESIN FLOORING - Project: - Location: - Substrate: - Preparation: - Resin flooring system: - Manufacturer:
More information2-part epoxy primer, levelling mortar, intermediate layer and mortar screed
Construction Product Data Sheet Edition 21/11/2016 Identification no: 02 08 01 02 007 0 000004 Sikafloor -161 Sikafloor -161 2-part epoxy primer, levelling mortar, intermediate layer and mortar screed
More informationThe width of single glazing. The warmth of double glazing.
Therma Insuation CI/SfB (31) Ro5 (M5) September 2011 The width of singe gazing. The warmth of doube gazing. Pikington Spacia Revoutionary vacuum gazing. Pikington Spacia Revoutionary vacuum gazing soution.
More informationGatic Vortex gives you control of drainage volume and speed.
Unicass Juy 2014 L731 CI/SfB (52.7) h Gatic Vortex gives you contro of drainage voume and speed. Speciaised Engineering. Specia Advice. Harness the power of Vortex Gatic Vortex has been deveoped to bring
More informationPRODUCT DATA SHEET Sikafloor -242 LC
PRODUCT DATA SHEET 2-PART VERSATILE COLORED EPOXY RESIN SYSTEM DESCRIPTION is a two part, multi-purpose, high build, coloured epoxy resin. USES may only be used by experienced professionals. Roller, textured
More informationFlowfast SR (3mm) Technical Profile
Technical Profile FIRE RESISTANCE EN 13505-1 SLIP RESISTANCE Method described in AS4586-2013 Bfl-s1 Dry & Wet Rating is dependant on specification (in accordance with AS4586-2013) Flowfast SR (3mm) A durable,
More informationConstruction. 2-part water based protective epoxy coating. Product Description. Product Data. Tests. Form
Product Data Sheet Edition 16/07/2007 Identification no: 02 08 01 01 014 0 000000 Sikagard -67 2-part water based protective epoxy coating Construction Product Description Sikagard -67 is a water based,
More informationSOAKWELL INFORMATION
www.pastube.com.au SOAKWELL INFORMATION This document gives detai s on the Pastube range of Soakwe products, incuding the physica characteristics. It aso describes simpe design measures for Pastube soakwes
More informationPRODUCT DATA SHEET Sikafloor -264 HC
PRODUCT DATA SHEET 2- PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part, coloured epoxy resin. USES may only be used by experienced professionals. is used as: Roller coat for concrete and cement
More informationPRODUCT DATA SHEET Sikafloor -264 HC
PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part, economic, solvent-free coloured epoxy resin. USES may only be used by experienced professionals. Roller coat for concrete
More informationSikafloor -264 HC is a two part, economic, solvent-free coloured epoxy resin.
Product Data Sheet Edition 2011-11_1 2-part epoxy roller and seal coat Construction Product Description is a two part, economic, solvent-free coloured epoxy resin. Uses Roller coat for concrete and cement
More informationFlowfast SRQ (2mm) Technical Profile
Technical Profile Flowfast SRQ (2mm) A highly decorative, non-slip, fastcuring MMA resin-based flooring system featuring a blend of coloured quartz granules. Typically used in internal and external applications
More informationPRODUCT DATA SHEET Sikafloor -264 HC
PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part, economic, solvent-free coloured epoxy resin. USES may only be used by experienced professionals. Roller coat for concrete
More informationRESIN FLOORING. To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING
M12 RESIN FLOORING To be read with Preliminaries/ General Conditions TYPE(S) OF FLOORING 110A RESIN FLOORING - Project: - Location: - Substrate: - Preparation: - Resin flooring system: - Manufacturer:
More informationFlowcoat OP (0.3mm) Technical Profile
Technical Profile (0.3mm) High performance, solvent free, epoxy resin coating system designed to create a uniform Orange Peel surface texture. Typically used as a hard wearing, protective, coloured floor
More informationConstruction. 2-part High-build Solvent Free Epoxy Coating. Product Description. Product Data. Storage
Construction Product Data Sheet Edition: 22.10.2012 Identification no. Version: GCC 2-part High-build Solvent Free Epoxy Coating Product Description is a two-part, high-build, solvent free, coloured epoxy
More information2-part Epoxy coating and seal coat
Product Data Sheet Edition 24/01/2008 Identification no: 02 08 01 02 013 0 000002 2-part Epoxy coating and seal coat Construction Product Description Sikafloor -264 is a two part, economic, solvent-free
More informationPRODUCT DATA SHEET Sikafloor -264 SG
PRODUCT DATA SHEET 2-PART HIGH-BUILD SOLVENT FREE EPOXY COATING DESCRIPTION is a two-part, high-build, solvent free, coloured epoxy resin. Suitable for use in hot and tropical climatic conditions. USES
More informationAssembly Instructions
Assemby Instructions GENERAL Optoeectronic semiconductor devices can be mounted in any position. Connection wires may be bent provided the bend is not ess than 1.5 mm from the bottom of the case. During
More information2-part epoxy primer, levelling mortar and mortar screed
Construction Product Data Sheet Edition 25/07/2014 Identification no: 02 08 01 02 007 0 00001 Sikafloor -156 2-part epoxy primer, levelling mortar and mortar screed Product Description Sikafloor -156 is
More informationLinear Shafts ov -linear -shaf ts-divider - U pdated
Linear Shafts ov-inear-shafts-divider - Updated - 18-09-2017 163 Linear Shafts Technica Information Linear shaft bars ov-inear-shafts-technica-info - Updated - 18-09-2017 Linear Shafts from Automotion
More informationChem-Stud Chem-Stud 56.1 Introduction Product Description Chem-Stud Capsule Specifications. Chem-Stud Recommended Setting Time
56.0 Chem-Stud 56.1 Introduction The Chem-Stud Anchor System consists of sef contained two-part gass capsues and matching chise pointed anchor rod which is instaed using a rotary hammer dri and rod adapters.
More informationSikafloor -264 HC is a two part, economic, solvent-free coloured epoxy resin.
Product Data Sheet Version 31/01/2014 (Indonesia editon 1, 2007) Sikafloor -264 HC 2-Part Epoxy Roller and Seal Coat Construction Product Description Uses Characteristics / Advantages Form Sikafloor -264
More informationSikafloor -375 is a two part, solvent free, low viscosity, tough elastic, crackbridging polyurethane resin coating. CHARACTERISTICS / ADVANTAGES
PRODUCT DATA SHEET 2-part PUR tough elastic, crack-bridging coating PRODUCT DESCRIPTION Sikafloor -375 is a two part, solvent free, low viscosity, tough elastic, crackbridging polyurethane resin coating.
More informationGood chemical and mechanical resistance Easy application Economical Liquid proof Gloss finish Slip resistant surface possible
Product Data Sheet Edition 09/05/2016 Identification no: 02 08 01 02 013 0 000002 Sikafloor -ZA Sikafloor -264 ZA 2-part epoxy roller and seal coat Construction Product Description Sikafloor -264 ZA is
More information2-part water dispersed epoxy coating
Product Data Sheet Edition 21/07/2008 Identification no: 01 08 01 01 014 0 000001 2-part water dispersed epoxy coating Construction Product Description Sikagard -Wallcoat N is a two part, coloured, water
More informationConstruction. 3-part cement and epoxy combination micro mortar for surface sealing. Product Description 1 1/5. Tests
Product Data Sheet Edition 29/11/2007 Identification no: 02 03 02 01 002 0 000002 SikaGard -720 EpoCem ZA 3-part cement and epoxy combination micro mortar for surface sealing Construction Product Description
More informationGREASE SEPARATORS INSTALLATION DIAGRAM 1 OILS AND GREASES SEDIMENTS
1. OILS AND GREASES: inet zone in which the turbuence of the inet fow is dampened and in which the substances with a specific weight ower than water (ois, foams, etc...) accumuate. 1 OILS AND GREASES 2.
More informationRole: Sales Manager Name: Sample SM Candidate Date: 26 June 2012
Roe: Name: Saes Manager Sampe SM Candidate Date: 26 June 2012 :: Introduction This Saes Taent Assessment report is designed to hep you understand the candidate s potentia fit to the seected roe. This report
More information3-component epoxy self-smoothing screed
Construction Product Data Sheet Edition 26/07/2016 Identification no: 01 08 01 02 050 0 000017 3-component epoxy self-smoothing screed Product Description Uses Characteristics / Advantages Product Data
More informationConstruction. Two-part Epoxy Roller and Seal Coat. Product Data Sheet Edition No. 01 (October 2015) Sikafloor -264 HC. Product Description
Product Data Sheet Edition No. 01 (October 2015) Two-part Epoxy Roller and Seal Coat Construction Product Description is a two part, economic, solvent-free colored epoxy resin. Uses Roller coat for concrete
More informationInternational Laboratory Accreditation Cooperation. Why use an Accredited Laboratory?
Internationa Laboratory Accreditation Cooperation Why use an Accredited Laboratory? What factors shoud you consider when choosing a aboratory? When seecting a aboratory to fufi your testing, caibration
More informationFlowcoat SK (0.35mm) Technical Profile
Technical Profile FIRE RESISTANCE EN 13505-1 SLIP RESISTANCE Method described in AS4586-2013 Bfl-s1 Dry & Wet Rating is dependant on specification (in accordance with AS4586-2013) (0.35mm) A light non-slip,
More informationCHARACTERISTICS / ADVANTAGES. Yellowish-transparent. PACKAGING 20 kg per pail
PRODUCT DATA SHEET Epoxy-resin binder for priming, levelling mortar and for screeds PRODUCT DESCRIPTION Sikafloor -156 is a colourless, 2-component low viscosity epoxy resin. USES For priming and levelling
More informationIndustrial Extrusion
Industria Extrusion The Best Twin-Screw Design for Powder Coating Baker Perkins manufactures a comprehensive range of twin-screw extruders specificay for powder coating production, from the MPX19 for sma
More informationFlowcoat OP (1.5mm) Technical Profile
Technical Profile (1.5mm) High performance, coloured, epoxy resin coating system designed to create a non slip textured surface in industrial facilities. Typically used as a hard wearing, protective, coloured
More informationPrimer and Moisture Control for Wood Floor Bonding with Elastic SikaBond Adhesives on Difficult Substrates
Construction Product Data Sheet Edition: 29/05/2013 Identification no: Version no: GCC Sika Primer MB+ Sika Primer MB+ Primer and Moisture Control for Wood Floor Bonding with Elastic SikaBond Adhesives
More informationFlowcrete MF (4mm) Technical Profile
Technical Profile FIRE RESISTANCE EN 13501-1 SLIP RESISTANCE Method described in AS4586-2013 B FL - s1 Dry & Wet Rating is dependant on specification (in accordance with AS4586-2013) Flowcrete MF (4mm)
More informationPRODUCT DATA SHEET Sikafloor -161
PRODUCT DATA SHEET 2-PART EPOXY PRIMER, LEVELLING MORTAR, INTERMEDIATE LAY- ER AND MORTAR SCREED DESCRIPTION is an economic, two parts, low viscosity, solvent free epoxy resin. "Total solid epoxy composition
More informationPRODUCT DATA SHEET Sikafloor 359 N
PRODUCT DATA SHEET TWO PART PUR TOUGH ELASTIC COLOUR SEAL COAT (ONLY TO BE APPLIED BY A SIKA APPROVED CONTRACTOR) PRODUCT DESCRIPTION TESTS APPROVAL / STANDARDS PRODUCT DATA FORM Sikafloor 359 N is a two
More information2-part epoxy self-smoothing and broadcast system. Sikafloor -263 SLHC is a two part, economic, multi purpose binder based on epoxy resin.
Product Data Sheet Edition 2011-11_1 2-part epoxy self-smoothing and broadcast system Construction Product Description is a two part, economic, multi purpose binder based on epoxy resin. Uses Self-smoothing
More informationFlowfast Terrosso (2mm)
Technical Profile Flowfast Terrosso (2mm) A seamless, rapid curing, decorative, durable MMA floor finish that transforms commercial and industrial environments. Typically used in public areas including
More informationFlowfresh SR (9mm) Technical Profile
Technical Profile Flowfresh SR (9mm) A heavy duty, antimicrobial polyurethane resin floor system offering an anti-slip, chemical resistant, textured matte finish. Typically used in heavy duty wet processing
More informationInverted Roofing System
Insua t i o n First Issue September 2018 Roofing System NEXT GENERATION INSULATION SOLUTION FOR PROTECTED MEMBRANE FLAT ROOFS AND GREEN ROOFS Idea for constructions where a ack of construction depth or
More informationTechnical support and product training
Technica support The British Gypsum Drywa Academy provides a singe point of contact for queries on the appication and use of the Company s products and systems. An experienced technica team is on hand
More informationCONCERTINA GRILLE TECHNICAL GUIDE
CONCERTINA GRILLE TECHNICAL GUIDE RETRACTABLE SECURITY GATES PROPERTY PROTECTION SYSTEMS Commercia Retai Counter & Cabinet Domestic CS11 Insurance Approved Retractabe Security Gates CS11 X Lattice S Lattice
More information4. Floor Substrate Testing Prior to Floor Paint application
4. Floor Substrate Testing Prior to Floor Paint application At Buy Floor Paint we have tried to summarise some simple and practical tests that you can do with commonly available materials and equipment,
More informationFlowcoat UV (1.5mm) Technical Profile
Technical Profile Flowcoat UV (1.5mm) High performance, hard-wearing, positively textured, coloured epoxy and polyurethane resin coating system. Typically used as a UV and slip resistant, durable coating
More information225 H. Matrix : Styrene divinylbenzene copolymer. Functional Group : Sulphonic acid. Total exchange capacity : 1.8 meq/ml, minimum
225 H Hydrochoric acid Regeneration Description INDION 225 H is a premium grade strong acid cation exchange resin containing suphonic acid groups. It is based on cross-inked poystyrene and has a ge structure.
More information2-part, electrostatically conductive epoxy coating
May 2009 Sikafloor -220 W Conductive 2-part, electrostatically conductive epoxy coating Construction Product Description Sikafloor -220 W Conductive is a two part, water dispersed, epoxy resin with a high
More informationSikafloor -161 HC is an economic, two part, solvent free, low viscosity epoxy resin.
Product Data Sheet Version 15/06/2015 (Indonesia edition 1/2007) Sikafloor -161 HC 2-Part Epoxy Primer, Levelling Mortar, Intermediate Layer and Mortar Screed Construction Product Description Uses Characteristics
More informationConstruction. 2-part epoxy roller and seal coat. Product Description
Construction Product Data Sheet Edition 27/10/2015 Identification no: 02 08 01 02 013 0 000002 Sikafloor -264 2-part epoxy roller and seal coat Product Description Sikafloor -264 is a two part, economic,
More information2-part, electrostatically conductive epoxy coating
Product Data Sheet Edition 15/08/2006 Identification no: 02 08 01 02 012 0 000001 2-part, electrostatically conductive epoxy coating Construction Product Description Uses Characteristics / Advantages Product
More informationOffers excellent resistance to heat loss or gain, which saves energy and lowers operating costs. A low thermal conductivity of.23 at 75 F (24 C).
Submitta MSDS Guide Specifications Description Knauf 1000 Pipe Insuation is a moded, heavy-density, one-piece insuation made from inorganic gass fibers bonded with a thermosetting resin. It is produced
More informationFlowfresh SR (9mm) Technical Profile
Technical Profile Flowfresh SR (9mm) A heavy duty, semi-gloss, antimicrobial polyurethane resin floor system offering an anti-slip, chemical resistant, textured finish. Typically used in heavy duty wet
More informationPRODUCT DATA SHEET Sikafloor -263 SL HC
PRODUCT DATA SHEET 2- PART EPOXY SYSTEM BY RESIN DESCRIPTION is a two part, multipurpose binder based on epoxy resin. USES may only be used by experienced professionals. is used as: Self-smoothing and
More informationINSTALLATION METHOD STATEMENT
INSTALLATION METHOD STATEMENT 1.0 Introduction - Liquid screed is a flowing screed flooring system comprising a calcium sulphate binder, fine aggregate and water. - It is for internal use only, in general
More informationPRODUCT DATA SHEET Sikafloor -264
PRODUCT DATA SHEET 2-PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is two part, economic, coloured epoxy resins. "Total solid epoxy composition acc. to the test method of Deutsche Bauchemie" USES may only
More informationPRODUCT DATA SHEET Sikafloor -264
PRODUCT DATA SHEET 2 PART EPOXY ROLLER AND SEAL COAT DESCRIPTION is a two part coloured epoxy resin. Suitable for use in hot and tropical climatic conditions. USES may only be used by experienced professionals.
More informationPRODUCT DATA SHEET Sika Level-315 F
PRODUCT DATA SHEET CEMENTITIOUS SELF LEVELLING, FAST DRYING, FIBRE REINFORCED UNDERLAYMENT FOR USE 3-15MM THICK ON INTERIOR FLOORS PRODUCT DESCRIPTION Sika Level-315 F is a one part, polymer modified,
More informationConstruction. Sodium silicate based surface hardener, dustproofer, sealing and curing compound for concrete. Product Description.
Construction Product Data Sheet Edition 19 November 2012 Sikafloor -CureHard-24 Sodium silicate based surface hardener, dustproofer, sealing and curing compound for concrete Product Description Sikafloor
More informationIQ ASSURED. Delivering Building Energy Management
IQ ASSURED Deivering Buiding Energy Management A BEMS can efficienty contro as much as 84% of your buiding s energy consumption but, to do so, it must be working effectivey The Buiding Energy Management
More informationUltralevel SL Self Levelling Cementitious Underlay
Technical Data Sheet Ultralevel SL Self Levelling Cementitious Underlay SMF26a 17.06.13 DESCRIPTION Bostik Ultralevel SL is a rapid hardening self-levelling, single component cementitious underlay. Bostik
More information