This specification describes the minimum requirements for piping systems for the following service:
|
|
- Brittney Peters
- 6 years ago
- Views:
Transcription
1 1.0 APPLICATION 2017/0/12 1/ This specification describes the minimum requirements for piping systems for the following service: Process Water or Underground Dewatering Service piping systems at pressures up to. Design Conditions F Operating ambient temperature Design, Fabrication, Assembly, Erection and Approval Requirements Piping Classification and Identification SPEC Identify and paint the piping system according to the requirements indicated on the project drawings or the scope of work. SPEC Piping General Requirements SPEC SPEC CSA B51 ASME B31.1 System Approvals Leak Testing Requirements Pressure Piping and Vessels - Quality Requirements Boiler, Pressure Vessel and Pressure Piping Code Power Piping Piping systems are subject to the approval of TSSA, Boilers and Pressure Vessels Safety Division. Note: Due to the ph of some mine water, this carbon steel material specification may not be suitable. 2.0 MATERIALS 3/4 and smaller Sch 80 per ASME B3.10, carbon steel ASTM A10 Gr. B, seamless, plain ends. Use schedule 10 where threaded connections are absolutely necessary and cannot be avoided. Pipe 1 to 8 Sch 80 per ASME B3.10, carbon steel ASTM A10 Gr. B, seamless, beveled ends " thick wall per ASME B3.10, carbon steel ASTM A10 Gr. B, seamless, beveled ends.
2 2017/0/12 2/ Pipe (cont d) 12 to 14" Sch 80 per ASME B3.10, carbon steel ASTM A10, Gr. B, seamless, beveled ends. 3/4 and smaller Class 3000 per ASME B1.11, forged carbon steel ASTM A105, socket welded. 1 to 8 Sch 80 per ASME B1.9, carbon steel ASTM A234 Gr. WPB, seamless, butt weld. Fittings " thick wall per ASME B1.9, carbon steel ASTM A234 WPB, seamless, butt weld. 12 to 14 Sch 80 per ASME B1.9, carbon steel ASTM A234 Gr. WPB, seamless, butt weld. Butt weld elbows to be long radius R = 1 1/2 x dia. unless otherwise noted. Use: Threadolet and sockolet, Class 3000 per ASME B1.11 and MSS SP-97, forged carbon steel ASTM A105. Branch Connections Weldolet, Extra strong per ASME B1.11 and MSS SP-97, forged carbon steel ASTM A105. For header sizes 12 and 14, use Class 000 or S10 for Sockolets, Thredolets and Weldolets Attachment to run pipe by full penetration welds. For connection type, see Appendix A Branch Connections 3/4 and smaller Class 00 per ASME B1.5, forged carbon steel ASTM A105 socket welded, raised face. Flanges 1 to 14 Class 00 per ASME B1.5, forged steel ASTM A105, welding neck type, raised face. Bore of welding neck flanges to suit pipe ID.
3 2017/0/12 3/ Threaded Joint Sealant Flanged Joint Gaskets Flange Bolting Unions Valves Use Teflon Tape. Do not use wet sealants. 1/1" - thick ring type - inside bolts, non-asbestos synthetic fibre, nitrile bonding, expanded metal reinforced. Dimensions to ASME B1.21. Gasket dope is not permitted. Klinger C-4409 or approved equal. Manufacturer's gasket material recommendation subject to Vale approval. Alloy steel stud bolts ASTM A193 Gr. B7, threaded full length, with semifinished heavy hex nuts ASTM A194 Gr. 2H with Class 2A fit on bolts and 2B fit on nuts. Dimensions to ASME B and ASME B Not suitable for this specification. Selection by the Engineer. Valves to be lockable. 3.0 EXAMINATION AND INSPECTION Examination and inspection must meet the requirements of ASME B31.1 and specific instructions in the scope of work. 100% visual examination for all sizes and thicknesses is required. 4.0 APPENDICES Appendix A: Branch Connections
4 2017/0/12 4/ 5.0 REVISION AND TRANSITION NOTES Revision notes describe: what was changed, and if applicable, why it was changed, and the plan to implement the change, including whether changes are retroactive. Note: The revision notes are a summary of the changes and may not necessarily be a complete list. A risk code is entered for each revision and if applicable, the revision notes will describe how risk was addressed for the revision. Risk Code A Risk Category This revision is a minor change and/or introduces no risk. B C Risk has been addressed for this revision by the reviewer and approver. Low risk or no new hazards identified. For this revision, a PHR or other risk management tool has been used to address risk and minimize hazards. This risk assessment has been documented and is available through Central Engineering. Rev Revision Notes Document format and number changed due to Vale Engineering Document Program changes in Previous Standard number Rev 2. Specification updated. Approved for use in Thompson. Piping system approval requirements updated for Manitoba. Reference to SPEC corrected in Reference document section. No technical changes. Risk Code Approved by Reviewed by Issue Date YYYY/MM/DD --- BML BML 2012/04/2 --- BML BML 2012/10/ AD BML 2012/11/23 4 See Rev 4 Notes Below --- MDF MDF 2015/05/ Review Reformatted Regional approvals removed - minor technical changes Added SPEC and removed Sec 3 Testing, Changed Section 1 Table title to include Assembly and Erection per Code, removed SPEC as welding will be per Code, corrected bolting ASME specification to B , 12 pipe to be sch80 per Code, removed use of slip on flanges (not per Code at design pressure), changed gasket to C metal reinforced to suit pressure. Removed instrument isolation valve. A M.Fogarty A.Delost 201/11/08 A M. Fogarty B. Morris 2017//22
5 2017/0/12 5/ REV 4 Notes Added ph comment. Added some reference codes. Changed Pressure Rating to Design Conditions, added temperature range to design and operating conditions. Added ASME B3.10 references to the Pipe Section. The lb. was removed from Class designations per ASME definition. ANSI was removed from ANSI/ASME designations. Added ASME B1.11 and MSS SP-97 reference to Branch Connection section. Weldolet branch connection changed to extra strong from standard for consistency with other U/G specifications. Removed taper bore comment as it does not apply because all componentsare Sch 80. Added 14 and above note for fittings. Added SPEC and PROC-8300 reference. Removed content that is in the SPEC or PROC for clarity. Added inspection criteria per code. Clarified examination requirements. Change flanged class from 400 to 00 as Class 400 pressure allowable is 990 PSIG non shock however dewatering systems require a water hammer allowance. Rev 4 changes are applicable to any new installations and/or modifications to existing systems from this date forward
6 APPENDIX A: BRANCH CONNECTIONS Inches B R A N /0/12 / C H / / Inches /4 1/2 HEADER 1 = Equal Tee 2 = Reducing Tee 3 = Threadolet, Sockolet 4 = Weldolet
This specification describes the minimum requirements for piping systems for the following service:
1.0 APPLICATION 2017/0/12 1/ This specification describes the minimum requirements for piping systems for the following service: Process Water or Underground Dewatering Service piping systems at pressures
More informationThis specification describes the minimum requirements for piping systems for the following service: Plant air systems operating up to 125 PSIG.
SPEC-3501 2016/11/0 1/9 1.0 APPLICATION This specification describes the minimum requirements for piping systems for the following service: Plant air systems operating up to 125 PSIG. Design Conditions
More informationThis specification describes the minimum requirements for piping systems for the following service:
1.0 APPLICATION 1/8 This specification describes the minimum requirements for piping systems for the following service: Gland Water Design Condition Operating Conditions 50 PSIG @ 150 F 0 to 5 PSIG @ 35
More informationº to 150º F In accordance with this specification and
SPEC-3006 2016/0/18 1/10 1.0 PURPOSE This specification describes the minimum requirements gland water piping systems operating at or below 400 PSIG. Gland water systems are to be constructed either of
More informationFor outdoor installations, see Vale Engineering Standard Specification SPEC
SPEC-3023 1/7 1.0 PURPOSE This specification describes the minimum requirements for dry (less than 100 ppm H20) gaseous sulphur dioxide at pressures up to and including 10 PSIG for indoor service. Do not
More informationREVISIONS App PC. App Sud. App Thom 2011/10/26 GS 2012/10/01 BL 2011/10/26. Pending GS 2012/10/01 BL 2012/10/23. Pending MDF 2011/10/26 GS 2013/04/22
1/14 Rev 1 2 3 Description Document format and number changed. Previous number 3503-02.01.621 Approved for use in Thompson Piping system Approval Requirements for MB updated Specification Reference Correction
More informationREVISIONS. App Thom. App Sud. App PC 2011/12/01 BM 2011/12/01 GS 2012/10/01. Pending BM 2011/12/01 GS 2012/10/01. Pending BN 2015/02/25
1/19 REVISIONS Rev Description Rev n by App Sud App PC App Thom App VB App LH App Clyd App Act Issue Date YYYY/MM/DD 1 2 Specification updated and format and number revised. Previous number 303-03.02.611
More informationOntario ENGINEERING STANDARD SPECIFICATION 1.0 PURPOSE 2.0 PIPING AND FITTINGS
SPEC-5022 1/12 1.0 PURPOSE This specification describes the minimum requirements for natural gas piping systems in industrial applications for up to 60 psi service downstream of the utility distributor
More informationwall Seamless ASTM A333 Grade 6. Item 1.36 (Outdoor) wall Electric Fusion Welded
Number: 6503-4.1.611 Rev. 5 Process Piping System CCNR IPC Plant Service: Process Gas Low Pressure & Process Gas Vent Legend: (PG) Rev Issued Revised Approved Reviewed 2 January 14, 1993 November 30, 1998
More informationThis specification, applies at any Vale locations indicated with approval on the cover page, with the following exceptions:
1/5 1.0 PURPOSE This specification describes the minimum requirements for cold potable water plumbing systems within buildings. 2.0 APPLICATION This specification, applies at any Vale locations indicated
More informationRegardless of any alternative pricing provided, a quotation for the items specified herein shall be provided.
1/5 1.0 PURPOSE This specification describes the minimum requirements for design, material and construction requirements for air receivers. Ensure the design and fabrication of equipment and associated
More informationRegardless of any alternative pricing provided, a quotation for the items specified herein shall be provided.
1/5 1.0 PURPOSE This specification describes the minimum requirements for design, material and construction requirements for Expansion tanks. Ensure the design and fabrication of equipment and associated
More informationPHOENIX TUBES & FITTINGS. Corrosion resistant. Exotic materials. International Quality. Effecient supply chain management. Fast track delivery
Effecient supply chain management Corrosion resistant International Quality Exotic materials Fast track delivery AN ISO 9001:2008 CO. Company Profile In the lifeline of industries, our fittings make sure
More informationTrading LLC. QUALITY IS OUR BASIC STRATEGY FOR SURVIVAL AND FUTURE GROWTH
Trading LLC. QUALITY IS OUR BASIC STRATEGY FOR SURVIVAL AND FUTURE GROWTH ABOUT US In the Middle East as well as in any major economy, Oil and Gas, Power and Water are among the core sectors. In the Emirates,
More informationCONTENTS. Fittings, Bends, and Intersections
CONTENTS Foreword.............................................................................. Committee Roster Introduction Summary of Changes Chapter I 100 Chapter II Part 1 101 102 Part 2 103 104 Part
More informationGas Station & C Store SECTION CWM Job No
SECTION 211010 - PART 1 - GENERAL 1.1 WORK INCLUDED A. Provide labor, materials, equipment and services to perform operations required for the complete installation and related Work as required in Contract
More information1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME)
Issued 2005/06/01 Section 15113 Valves Cast Steel: Gate, Globe, Check, Ball Page 1 of 5 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National
More informationEQT MIDSTREAM DESIGN AND CONSTRUCTION MANUAL DESIGN STANDARD WELDING AND JOINING 3.4 HOT TAP AND BRANCH CONNECTIONS Total Pages: 13
Table of Contents Scope... 845 References... 845 Governmental... 845 EQT Midstream Publications... 845 Industry Standards... 846 Computer Programs... 846 1 Manufactured Branch Connections... 846 1.1 Extruded
More informationBASIC OF PIPING MATERIAL
By: Miduk Aritonang 1. MATERIAL MATERIAL METAL NON METAL: - Plastic : Fibre Rainforced Plastic (FRP), etc - Polymer : PE, PVC, PTFE/Teflon, etc FERRO: - Carbon Steel (CS) - Low Temperature Carbon Steel
More informationISO 9001:2008 IML Italy, Delcorte France, Metalfar Italy, ULMA Spain
Tylos Oilfield Services WLL was initially handled by Tylos Building Materials EST, and due to the increase in business volume became an independent establishment in 2008 to handle the oilfield related
More informationAll our products Quality Assurance QUALITY Ensure quality control and it strive for the following:
ALTOWS COMPANY ABOUT US ALTOWS CO. is a premium supplier of top quality piping components and fittings which include various pipes, tubes, threaded fittings, flanges, fasteners, bars, rods etc. Our products
More informationFORGED PRODUCTS & FLANGE FITTING PIPE TUBE PLATE AND OTHER MATERIALS
DOOLIM METAL CO. FORGED PRODUCTS & FLANGE FITTING PIPE TUBE PLATE AND OTHER MATERIALS 두림메탈 Doolim Metal Co. Dear Sirs, We sincerely thank you for your interest and consideration for our company. As a reliable
More informationASME B31.3 Process Piping. 19. What s Different in B31.1
ASME B31.3 Process Piping Charles Becht IV, PhD, PE Don Frikken, PE Instructors BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-1 19. What s Different in B31.1 Scope Organization of the Code
More informationOntario ENGINEERING STANDARD SPECIFICATION. 3.1 Submit schedules showing the proposed dates for tie-ins to existing piping systems.
1/12 1.0 PURPOSE This specification describes the minimum requirements for the installation of a fully operational piping system in accordance applicable Codes and Vale Standards. Piping systems include
More informationASTM Standards B127 B160 B161 B162 B163 B164 B165 B166 B167 B168 B333 B335 B407 B408 B409 B423
ASTM Standards : B127 Specification for Nickel-Copper Alloy (UNS N04400) Plate, Sheet, B160 Specification for Nickel Rod and Bar B161 Specification for Nickel Seamless Pipe and Tube B162 Specification
More informationCOMMITTEE CORRESPONDENCE ASME B16-F, FITTINGS
Page 1 of 6 6/14/2016 TO: NOTE FOR RECORD FROM: GUY A. JOLLY SUBJECT: ASME B16.11 HISTORY SPECIFIC TO SW FITTINGS ASA B16.11-1946, 1 ST EDITION, STEEL SOCKET-WELDING FITTINGS 1. This edition did not have
More informationPIP PNSM0115 Purchasing Requirements for Pipe
December 2016 Piping PIP Purchasing Requirements for Pipe PURPOSE AND USE OF PROCESS INDUSTRY PRACTICES In an effort to minimize the cost of process industry facilities, this Practice has been prepared
More informationCode. 1) Code. Standard or Specification. Bolting
Code 1. Code 1) Code (1) ASME B 31.1 : Power Piping (2) ASME B 31.3 : Process Piping (3) ASME B 31.4 : Pipeline Transportation Systems for Liquid Hydrocarbons and Other Liquids 2) Material Code Bolting
More informationSEA Certified Piping Design Engineer
SEA Certified Piping Design Engineer Certification Course Course Title Eligibility Criteria : SEA CERTIFIED PIPING DESIGN ENGINEER : Mechanical Engineer, Chemical & Petroleum Engineer Duration of Course
More informationQuality Suppliers of Buttweld Pipes Fittings Forged Fittings, Flanges Outlets & Fasteners
SIVOX STEEL (INDIA) Head Office nd No. 13, 2 Floor, Narayan Building, Ardeshir Dadi Street, Girgaon, Mumbai, 400 004, India. T/F: +91 22 6749 6271 Regd. Office No. 6, Ground Floor, Lavdeep Apartment, Dhumal
More informationDesign Standard HVAC Piping
Design Standard Revisions Log: Version Date Description of changes/updates 2 April 30, 2015 Expansion of direction pertaining to rooftop installations of copper piping Purpose: The heating, ventilating
More informationEos Common Steel Piping Database for Sage Timberline Office Estimating
for Sage Timberline Office Estimating Introduction The Common Steel Piping Database for Sage Timberline Office Estimating is designed to support piping estimating for buildings, process facilities, power
More informationGUJARAT NARMADA VALLEY FERTILIZERS & CHEMICALS LIMITED
CONTENTS 1. Scope 2. Referenced Documents 3. Abbreviations 4. Materials and Manufacture 5. Dimensions 6. Inspections and Tests 7. Markings 8. Preparation for Shipment - 1 - 1. Scope 1.1 This specification
More informationPipe. Valves. Fittings. Fasteners. Tube and Tube Fittings. And Much More
Pipe Valves Fittings Fasteners Tube and Tube Fittings And Much More Tubing Sizes Materials 1/16" to 6" Diameter Stainless A269 & A511 Copper Monel Inconel Hastelloy DK Lok Tube Fittings Sizes Products
More informationSpecification for Pipe Fittings
Specification for Pipe Fittings Specification for Pipe Fittings Page 1 of 11 Table of Contents 1.0 SCOPE...3 2.0 DEFINITIONS...3 3.0 REFERENCES, CODES AND STANDARDS...3 4.0 CONTRACTOR'S RESPONSIBILITIES...4
More informationREVISIONS. App Sud. App Thom. App PC AA 2011/12/09 AA 2012/07/19 AA 2013/02/28 AA 2013/10/18 AA 2013/11/27 AA 2013/11/29 AA 2014/03/06 AA 2014/12/17
- FABRICATION 1/12 REVISIONS Rev 1 2 3 Description Document format and number changed. Previous number 1402-01.01.311 Associated Drawings added See REV note 2 Associated Drawing for Ladders added See REV
More informationBS, ASTM, DIN, IS, ANSI, ASME
COMPANY PROFILE Established in the year 1973, we, 'Haresh Steel Centre, Mumbai', have gained specialization in manufacturing, exporting, supplying and trading a wide range of Pipes, Fittings, Flanges,
More informationDesign and Construction Standards SECTION HYDRONIC PIPING
SECTION 15510 HYDRONIC PIPING PART 1 GENERAL 1.1 REFERENCES A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More information1.2 REFERENCES.1 American National Standards Institute (ANSI)/American Society of Mechanical Engineers (ASME).
Issued 2005/06/01 Section 15112 Valves Cast Iron, Gate, Globe, Check Page 1 of 8 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards
More informationASME B16.5 History Rev Page 1 of 9
Page 1 of 9 Presented here is a history of the development of ASME B16.5, Pipe Flanges and Flanged Fittings prepared by Guy Jolly and Don Frikken. Topics included in separate sections are: 1. General History
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 15510 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications. B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300. C. ANSI/ASME
More informationCOMPANY SHORT PRESENTATION
Single source supplier of complete piping packages ICARUS SA is a leading single source supplier of complete piping packages and manufacturer of specialty valves, compact flanges acc Norsok L-005 and tailor
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:
More informationSECTION HYDRONIC PIPING
PART 1 GENERAL 1.1 REFERENCES SECTION 23 21 13 HYDRONIC PIPING A. ANSI/ASME SEC 9: Welding and Brazing Qualifications B. ANSI/ASME B16.3: Malleable Iron Threaded Fittings Class 150 and 300 C. ANSI/ASME
More informationA. Product Data: For Piping, fittings, transition fittings and dielectric fittings.
SECTION 22 11 16 - DOMESTIC WATER PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationINDUSTRIAL VALVES PIPING PACKAGES VARIOUS EQUIPMENT
INDUSTRIAL VALVES PIPING PACKAGES VARIOUS EQUIPMENT UNIVERSAL S.R.L. HEAD OFFICE FACTORY: 29010 TREVOZZO DI NIBBIANO V.T.(PC) ITALY- VIA MOLINO FRANZINI 13 TEL.+39/0523997677 TELEFAX +39/0523997354 VAT:
More information6.1 General. This chapter shall provide requirements for correct use of sprinkler system components and hardware.
NFPA 13-Proposed 2013 Edition Standard for the Installation of Sprinkler Systems TIA Log No.: 1054 Reference: Chapter 6 Comment Closing Date: June 1, 2012 Submitter: Bob Caputo, Fire & Life Safety America
More informationASTM A420-Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service
ASTM A420-Standard Specification for Piping Fittings of Wrought Carbon Steel and Alloy Steel for Low-Temperature Service 1. Scope 1.1 This specification 2 covers wrought carbon steel and alloy steel fittings
More informationA. Compatibility: Products shall be suitable for piping service fluids, materials, working pressures, and temperatures.
SECTION 23 05 16 PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationSECTION STEAM AND CONDENSATE HEATING PIPING
PART 1 GENERAL 1.01 SECTION INCLUDES A. Pipe and pipe fittings. B. Pipe hangers and supports. C. Valves. D. Steam piping system. E. Steam condensate piping system. 1.02 RELATED REQUIREMENTS A. Section
More informationBuilding Services Piping
ASME B31.9-2014 (Revision of ASME B31.9-2011) Building Services Piping ASME Code for Pressure Piping, B31 AN AMERICAN NATIONAL STANDARD ASME B31.9-2014 (Revision of ASME B31.9-2011) Building Services Piping
More informationASME B31.3 CUMULATIVE INDEX INTERPRETATIONS VOLS SUBJECT INDEX. Assembly and Erection Authorized Inspector (see Owner s Inspector)
SUBJECT INDEX Acceptance Criteria pressure tests 1-2 weld 1-1 1-9 1-14 1-41 2-8 5-09 5-13 5-17 5-18 5-20 6-04 7-06 8-32 12-22 13-16 14-02 14-07 24-03 24-26 Additive Manufacturing 25-39 25-40 Allowable
More informationEast Central College
SECTION 221116 - DOMESTIC WATER PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationFittings. Elbow Pipe. Specifications:
Elbow Pipe This type of fitting is widely used in piping systems to connect two straight sections of pipes of equal or different nominal diameter and with a curvature at a certain angle to change its direction;
More informationDirect contact and metal-to-metal seating make the T-pattern globe stop valve ideal for most shut-off applications.
Direct contact and metal-to-metal seating make the T-pattern globe stop valve ideal for most shut-off applications. Features Heavy integral Stellite hardfacing on both body and disc seating surfaces. Conical
More informationQuality Control How to Order and Specify Branch Connections Standard... 8,9. Extra Strong... 10,11. Schedule 160/XX Strong...
BRANCH CONNECTIONS , Weldolet, Thredolet, Sockolet, Flexolet, Latrolet, Elbolet, Sweepolet, Insert Weldolet, Nipolet, Brazolet, and Coupolet, are trademarks registered for the exclusive use of Bonney Forge
More informationADDENDUM NUMBER 1 PARTICULARS 1.01 DATE: APRIL 6, 2018
PARTICULARS 1.01 DATE: APRIL 6, 2018 ADDENDUM NUMBER 1 1.02 PROJECT: MIDLANDS TECHNICAL COLLEGE NE CAMPUS - CET CHILLER REPLACEMENT 1.03 OWNER'S PROJECT NUMBER: H59-N991-FW 1.04 ENGINEER: GMK ASSOCIATES
More informationQuality Control How to Order and Specify Branch Connections Standard... 8,9. Extra Strong... 10,11. Schedule 160/XX Strong...
BRANCH connections , Weldolet, Thredolet, Sockolet, Flexolet, Latrolet, Elbolet, Sweepolet, Insert Weldolet, Nipolet, Brazolet, and Coupolet, are trademarks registered for the exclusive use of Bonney Forge
More informationSeptember 6, 2016 Page 1 of 5
September 6, 2016 Page 1 of 5 1. SECTION 16100 Drawing E4.3, Note #39: Reference to the radio fire alarm panel and the fire station alerting master panel does not relate to the building fire alarm system.
More informationConsolidated* /2/3 Series (1) Electromatic* Ball Valve System
Technical Specifications Rev. C - 09/2018 Consolidated* 3500-1/2/3 Series (1) Electromatic* Ball Valve System Provides automatic or manual overpressure startup for steam boiler systems and assists startup
More informationPOWER PIPING J\$ME TO ASME B3I.I THE COMPLETE GUIDE. Charles Becht IV PRESS
POWER PIPING THE COMPLETE GUIDE TO ASME B3I.I by Charles Becht IV J\$ME PRESS Contents About the Author List of Figures List of Tables iii ix xi Chapter 1 Background and General Information 1 1.1 History
More informationPRODUCT: WELDED PIPE SPECIFICATION: 355.6*9.52 MATERIAL: S32205 PRODUCT: SEAMLESS PIPE. SPECIFICATION: Φ33mm*1mm MATERIAL: S31803
Special Piping Materials is renowned for the high volume of Duplex and Super Duplex products that it stocks. It supplies these materials to countless companies around the world who use its product s in
More informationBuilding Services Piping
ASME B31.9-2017 (Revision of ASME B31.9-2014) Building Services Piping ASME Code for Pressure Piping, B31 AN AMERICAN NATIONAL STANDARD ASME B31.9-2017 (Revision of ASME B31.9-2014) Building Services Piping
More informationSTAINLESS STEEL PIPE/TUBE & PIPE FITTINGS
STAINLESS STEEL PIPE/TUBE & PIPE FITTINGS In 1984, our journey into the business of repairing valves and industrial instrumentation began. That journey has led us to represent and service well known American
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION
Page 210500-1 SECTION 210500 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationPRO Alloy is Europe s leading stockholder for Stainless, Duplex, Super Duplex, Chrome Moly flanges and fittings.
Stainless, DUPLEX, Super Duplex flanges and fittings PRO Alloy is Europe s leading stockholder for Stainless, Duplex, Super Duplex, Chrome Moly flanges and fittings. introduction Our inventory consists
More informationRHINO VALVES WORLDWIDE. Cryogenic C44/C600 CRYOGENICS
RHINO VALVES WORLDWIDE Cryogenic C44/C600 CRYOGENICS Based on the Series 44, this valve has an extended stem to move away the drops cryogenic temperatures of the operator (human or automatic). This valve
More informationSection 11. API 7500lb Mud Gate Valves
Section 11. API 7500lb Mud Gate Valves Section 11a API 7500lb Rubber Seated Mud Gate Valves Gate Valves are designed and manufactured in accordance with the following specifications:- API 6A ANSI B31.3
More informationSECTION PLUMBING PIPING
SECTION 22 1000 PLUMBING PIPING PART 1 GENERAL 1.1 QUALITY ASSURANCE A. Perform Work in accordance with authority having jurisdiction standards. Utilize products as indicated in drawings and as allowed
More informationA. General provisions and other plumbing systems are specified in other Sections of Division 22.
PART 1: GENERAL 1.01 DESCRIPTION: A. General provisions and other plumbing systems are specified in other Sections of Division 22. B. This Section covers the natural gas system and equipment. C. See Section
More informationBrown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC PIPES AND TUBES
SECTION 23 20 00 - HVAC PIPES AND TUBES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes pipe and pipe fittings for: heating water, chilled water, steam and steam condensate, condenser water, glycol,
More informationSECTION TAPPING SLEEVES AND VALVES
SECTION 33 12 16.17 TAPPING SLEEVES AND VALVES PART 1: GENERAL 1.01 SCOPE Furnish, install and test all tapping sleeves, tapping valves, and tapping saddles as shown on the Drawings. 1.02 RELATED WORK
More informationShubham Enterprise.
+91-8048017823 Shubham Enterprise http://www.projectspipefittings.com/ We are leading wholesalers, suppliers and exporters of a wide variety of Stainless Steel Components. Our wide assortment of products,
More informationASTM Standards for Pipe & Fittings
for Pipe & Fittings There are many International Standards for stainless and carbon steel pipes and fittings. The list below is a basic overview of some of these. For more in-depth details of these Standards
More informationMASTERSPEC TECHNICAL SPECIFICATIONS DIVISION 23 HVAC
SECTION 230500 - COMMON WORK RESULTS FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Piping materials and installation instructions common to most piping systems. 2. Dielectric
More informationChrome Moly flanges and fittings
Chrome Moly flanges and fittings PRO Alloy is Europe s leading stockholder for Stainless, Duplex, Super Duplex, Chrome Moly flanges and fittings. introduction Our inventory consists of a complete range
More informationSTANDARD TECHNICAL SPECIFICATION FOR FLOW ORIFICE ASSEMBLY with ACCESSORIES
STANDARD TECHNICAL SPECIFICATION FOR FLOW ORIFICE ASSEMBLY with ACCESSORIES VOLUME - IIB SECTIONS-C & D SPECIFICATION No: PE-TS-XXX-145-I105A BHARAT HEAVY ELECTRICALS LIMITED POWER SECTOR PROJECT ENGINEERING
More informationCONTENTS --`,,```,,,,````-`-`,,`,,`,`,,`---
Buttwelding Ends CONTENTS Foreword... iv Committee Roster... v Correspondence With the B16 Committee... vi Summary of Changes... vii 1 Scope... 1 2 Transition Contours... 1 3 Welding Bevel Design... 2
More informationASTM B363-06a Standard Specification for Seamless and Welded Unalloyed
Standard Specification for Seamless and Welded Unalloyed Titanium and Titanium Alloy Welding Fittings 1. Scope :- 1.1 This specification cover fittings intended for general corrosion resisting and elevated
More informationSECTION HVAC PIPING
SECTION 23 21 13 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Heating Water Piping, Buried 2. Heating Water Piping, Above Ground 3. Chilled Water Piping, Buried 4. Chilled Water Piping, Above Grade
More informationStandard Tube & Pipe Adapters
Standard Tube & Pipe Adapters 1 to 8 OD Tube Sizes, 1 to 8 NPS Pipe Sizes Aluminum, Stainless Steel, Carbon Steel, Galvanized (Zinc-Coated) Steel. 11, 14, 16 Gauge Tube Wall Thicknesses; Schedule 5, 10,
More informationCopper-Nickel Products Copper-Nickel Tubing Fittings, Flanges, Sheet, Plate and Rod
Copper-Nickel Products Copper-Nickel Tubing Fittings, Flanges, Sheet, Plate and Rod ALASKAN COPPER WORKS ALASKAN COPPER & BRASS COMPANY C opper-nickel alloys are used in ship board and offshore drilling
More informationWELCOME TO TRUS GLOBAL CO.,LTD TOTAL SOURCING SOLUTION COMPANY
WELCOME TO GLOBAL CO.,LTD TOTAL SOURCING SOLUTION COMPANY 1. Index 1. Index 2. Introduction 3. Pipe Supply 4. Fitting Supply 5. Flange Supply 6. Hammer Wing Union Supply 7. Bolt / Nut Supply 8. Gasket
More informationConsolidated* Electromatic* Ball Valves
GE Oil & Gas Technical Specifications 05/2012 3500 Series Consolidated* Electromatic* Ball Valves Provides automatic or manual overpressure startup for steam boiler systems and assists startup and shutdown
More informationMILITARY STANDARD SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS
NOTICE OF CHANGE INCH-POUND 19 February 2002 MILITARY STANDARD SCHEDULE OF PIPING, VALVES, FITTINGS, AND ASSOCIATED PIPING COMPONENTS FOR NAVAL SURFACE SHIPS TO ALL HOLDERS OF : 1. THE FOLLOWING PAGES
More informationCROMONIMET STEEL LIMITED
+91-8048076501 CROMONIMET STEEL LIMITED https://www.indiamart.com/cromonimetsteel/pdf1.html We are a well- known Manufacturer, Exporter, Supplier and Importer of Stainless Steel Round Bar / Pipes and Tubes,
More informationBALL VALVES SPECIFICATION
DOCUMENT NO: 0000-TS-L006 BALL VALVES SPECIFICATION Prepared By: Chevron Niugini Project Services Limited 6 28 Feb 02 Approved for Construction SAC MGB PRW PRW LRF 5 04 May 01 Approved for Construction
More informationCity of Winnipeg BASES, HANGERS AND SUPPORTS Section NEWPCC - Pump Well Isolation Page 1 of 6 Tender No June 2003
NEWPCC - Pump Well Isolation Page 1 of 6 PART 1 General 1.1 RELATED SECTIONS.1 Section 01001 General Requirements..2 Section 03300 - Cast-in-Place Concrete..3 Section 05121 - Structural Steel for Buildings..4
More informationSTOCKIST SUPPLIERS & EXPORTERS:
PIPES & TUBES: Stainless Steel: ASTM A 312, A 213, A 213, A 249, A 269, A 358, A 240, A 276 Type: 202, 304, 304L, 304, 304H, 316, 316L, 316Ti, 321, 321H, 317, 317L, 310, 310S, 409, 410, 420, 430 etc. Carbon
More informationFLANGE DIMENSIONS TABLE TYPES
ADELAIDE BRISBANE PERTH OVERVIEW FLANGE DIMENSIONS TABLE TYPES In Australia the BS and AS flange standards are essentially the same but have been metricated. Consequently metric sizes are stated as DN
More information+91-8048762934 Ratna Exports http://www.ratnaexports.com/ We are engaged in the business of manufacturing, exporting and retailing Industrial Pipes, Forged Fittings and Flanges. Characterized by dimensional
More informationService Saddles/ Brass Alloy/ Stainless Steel Straps for Cast, Ductile & PVC Pipe
F 1 F 1.1 F 1.2 F 2 F 2.1 F 3 Service Saddles/ Hinged Type for 2 PVC Service Saddles/ Brass Alloy/ Stainless Steel Straps for Cast, Ductile & PVC Pipe Service Saddles/ Ductile Iron/ Stainless Steel Straps
More informationFLANGE DIMENSIONS TABLE TYPES
ADELAIDE BRISBANE PERTH OVERVIEW FLANGE DIMENSIONS TABLE TYPES In Australia the BS and AS fl ange standards are essentially the same but have been metricated. Consequently metric sizes are stated as DN
More information.1 ANSI/ASME B31.1, Power Piping, (SI Edition)..2 American Society for Testing and Materials (ASTM)
Fitness Facility Addition Page 1 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 03300 - Cast-in-Place Concrete.2 Section 05121 - Structural Steel for Buildings.3 Section 05500 - Metal Fabrications 1.2 REFERENCES.1
More informationNot Just Tight Shut Off Very Tight Shut Off!
APV-LLK-2 DELATITE VALVES Not Just Tight Shut Off Very Tight Shut Off! The Latest Technology in Severe Service Ball Valves Zero Leakage High Pressure High Temperature Metal Seated Repairable Model APV-LLK-2
More informationMETAL & DUAL SEATED PISTON VALVES
VP Series VESSEL & REACTOR VALVES METAL & DUAL SEATED PISTON VALVES PROCESS VALVES HIGH PERFORMANCE PISTON VALVES Dual Seal Piston Valve Code: VP4D-VP6D High sealing performance of Dual Seal specially
More informationMeter Connection Products: Overview
: Overview Georg Fischer Central Plastics entered the meter connection business in 1955 with the design and introduction of the insulated meter swivel and insulated union. We understand the critical nature
More informationVESSEL & REACTOR VALVES. VR Series RISING DISC PROCESS VALVES. Sold by: G&W Industrial Sales
VR Series VESSEL & REACTOR VALVES RISING DISC PROCESS VALVES CRUST BREAKING BOTTOM OUTLET VALVES Rising Disc Valves M Seal for high Pressure & Temperature. Dual Seal, Soft Seal, M Ring and M Control are
More informationSECTION FACILITY NATURAL-GAS PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS
SECTION 221223 - FACILITY NATURAL-GAS PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 0 1 Specification
More informationINSULATED JOINTS. Monolithic Joints for Electrically Isolating Pipelines
INSULATED JOINTS Monolithic Joints for Electrically Isolating Pipelines INSULATED JOINTS TUBE TURNS INSULATED JOINTS are a pre-fabricated, non-separable, union used to isolate specific sections of pipelines
More information