ASME B31.3 Process Piping. 19. What s Different in B31.1

Size: px

Start display at page:

Download "ASME B31.3 Process Piping. 19. What s Different in B31.1"

Bernadette Hudson
6 years ago
Views:

1 ASME B31.3 Process Piping Charles Becht IV, PhD, PE Don Frikken, PE Instructors BECHT ENGINEERING COMPANY, INC. What s Different in B What s Different in B31.1 Scope Organization of the Code Fluid Service Requirements Bases for Allowable Stresses Material Requirements Pressure Design Requirements Valve Requirements Fabrication and Installation Inspection, Examination and Testing BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-2

2 B31.1 Scope Rules for this Code Section have been developed considering the needs for applications which include piping typically found in electric power generating stations, industrial and institutional plants, geothermal heating systems and central and district heating and cooling systems. (100.1) BECHT ENGINEERING COMPANY, INC. What s Different in B B31.1 Scope Power piping systems as covered by this Code apply to all piping and their component parts They include but are not limited to steam water oil gas air [ ] BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-4

Boiler External Piping (BEP) Generally defined as piping between the boiler and the first block valve. BECHT ENGINEERING COMPANY, INC. What s Different in B31.

3 Boiler External Piping (BEP) Generally defined as piping between the boiler and the first block valve. BECHT ENGINEERING COMPANY, INC. What s Different in B Boiler External Piping Technical requirements are in accordance with B31.1 Administrative requirements are defined in ASME B&PV Code Section I and include requirements for B&PV Code stamp Data reports Quality control Inspection BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-6

4 Organization of the Code I II III IV V VI Scope and Definitions Design Materials Dimensional Requirements Fabrication, Assembly, and Erection Inspection, Examination and Testing BECHT ENGINEERING COMPANY, INC. What s Different in B Organization of the Code Appendices similar to B31.3 except II Rules for Design of Safety Valve Installations IV Corrosion Control V Recommended Practice for Operation, Maintenance and Modification VII Design of Restrained Underground Piping BECHT ENGINEERING COMPANY, INC. What s Different in B31.1-8

5 Organization of the Code B31.1 provides specific requirements for Boiler External Piping (Steam, Feedwater, Blowoff, Blowdown and Drains) Blowoff and Blowdown Piping (Non-BEP) Instrument, Control and Sample Piping Spray Type Desuperheater Piping Pressure Reducing Valves Pressure Relief Piping BECHT ENGINEERING COMPANY, INC. What s Different in B Organization of the Code B31.1 provides specific requirements for Piping for Flammable or Combustible Liquids Piping for Flammable Gases and Toxic Fluids Piping for Corrosive Fluids Temporary Piping Steam Trap Piping Pump Suction and Discharge Piping District Heating and Steam Distribution Systems BECHT ENGINEERING COMPANY, INC. What s Different in B

6 Fluid Service Requirements B31.1 does not define specific fluid services, but does have limitations for piping systems handling certain fluids Specific requirements for components and joints are described in paras BECHT ENGINEERING COMPANY, INC. What s Different in B Pipe Fluid Service Requirements Furnace butt welded pipe is not permitted for flammable, combustible or toxic fluids BECHT ENGINEERING COMPANY, INC. What s Different in B

7 Joint Fluid Service Requirements Socket welding size limited for BEP and toxic fluids Threaded joints size limited by temperature and pressure; example maximum pressure for NPS 3 joint is 400 psi (2750 kpa) Pipe thinner than STD WT may not be threaded Pipe shall be Sch 80 seamless for Steam over 250 psi (1750 kpa) Water over 100 psi (700 kpa) and 220ºF (105ºC) BECHT ENGINEERING COMPANY, INC. What s Different in B More Joint Fluid Service Requirements OD tubing compression and flared tubing limited to 2 in. (50 mm) Brazed joint may not be used for flammable or toxic fluids in fire hazard areas Soldered joints may not be used for flammable or toxic fluids Soldered joints may not be used in piping subject to vibration BECHT ENGINEERING COMPANY, INC. What s Different in B

8 Flanged Joint Requirements B31.1 has detailed requirements for flanged joints. Requirements include: Class 150 steel flanges bolted to Class 125 cast iron flanges are required to be flat faced gasket required to be full face Bolting dimensions for both US customary and metric bolting Bolt material requirements as a function of flanges and gaskets BECHT ENGINEERING COMPANY, INC. What s Different in B Bases for Design Stresses Most Materials (materials other than gray iron, malleable iron and bolting) below the creep range, the lowest of the specified minimum tensile strength divided by 3.5 1/3 of tensile strength at temperature 2/3 of specified minimum yield strength 2/3 of yield strength at temperature; except for austenitic stainless steels and nickel alloys with similar behavior, 90% of yield strength at temperature BECHT ENGINEERING COMPANY, INC. What s Different in B

9 Bases for Design Stresses ASTM A106 Grade B Carbon Steel (US Customary Units) Allowable Stress (ksi) /3 Yield Ultimate / 3 Ultimate / 3.5 B31.3 Allowable B31.1 Allowable Temperature (F) BECHT ENGINEERING COMPANY, INC. What s Different in B B31.1 Material Requirements Materials for BEP must meet ASME B&PV Code requirements; unlisted materials may not be used Unlisted materials may be used for OD tubing compression and flared tube fittings Use at temperatures above maximum in stress tables generally not permitted No rules for use at temperatures below -20ºF (-29ºC) BECHT ENGINEERING COMPANY, INC. What s Different in B

10 Pressure Design The rules for pressure design are essentially the same as for B31.3, but they are not identical. The two Section Committees are working to make the requirements the same. BECHT ENGINEERING COMPANY, INC. What s Different in B Design Pressure & Temperature allowance for pressure and temperature variation: The Code allows the design pressure to be set below the most severe coincident pressure and temperature for the following variations: Can exceed allowable by 20% for no more than 1 hr/event and no more than 80 hr/year Can exceed allowable by 15% for no more than 8 hr/event and nor more than 800 hr/year BECHT ENGINEERING COMPANY, INC. What s Different in B

11 Design Pressure & Temperature allowance for pressure and temperature variation - conditions: Except as limited by component standards Except as limited by manufacturers No limitations on cast iron or other non-ductile components No limitations on yield strength No limitations on longitudinal No limitations with respect to test pressure No permission from the owner required BECHT ENGINEERING COMPANY, INC. What s Different in B Valve Requirements Standard Valves Can be used within their pressure-temperature ratings and any additional limitations described in the Code Nonstandard Valves Shall be of a design which the manufacturer recommends for the service BECHT ENGINEERING COMPANY, INC. What s Different in B

12 Valve Requirements All Valves must have blow-out proof stems OS&Y required for NPS 3 and larger above 600 psi (4150 kpa) screwed bonnets not permitted for steam above 250 psi (1750 kpa) BECHT ENGINEERING COMPANY, INC. What s Different in B Fabrication and Installation Welder & brazer qualification and bending & forming requirements are very similar but not identical Preheating and heat treatment requirements are different B31.3 requires neither preheating or heat treatment for carbon steel with thickness less than or equal to 3/4 in. (19.0 mm) B31.1 requires preheating to 200ºF (95ºC) or heat treatment for the same thickness range BECHT ENGINEERING COMPANY, INC. What s Different in B

13 Fabrication and Installation Minimum socket weld size is 1.09 times nominal wall thickness versus B31.3 requirement for 1.25 time pressure design thickness Flange faces are required to be fitted so that gasket contact surfaces bear uniformly on the gasket Bolts must be threaded trough the nut BECHT ENGINEERING COMPANY, INC. What s Different in B Inspection, Examination and Testing Similar distinction between inspection and examination, but no specific owner s inspector Authorized inspector required for boiler external piping, ASME B&PV Code, Section I B31.1 does not include the concept of random with progressive examination either 100% or none BECHT ENGINEERING COMPANY, INC. What s Different in B

14 Inspection, Examination and Testing Examination is as required by Table 136.4: Over 750 F (400 C) Visual plus For NPS 2, MP or LP For NPS > 2, 100% radiography Over 1025 psig (70 bar) and 350 to 750 F (175 to 400 C) Visual plus For wall thickness ¾ (19 mm), 100% radiography All Others Visual only BECHT ENGINEERING COMPANY, INC. What s Different in B Inspection, Examination and Testing Visual examination is required for all welds with para acceptance criteria No surface cracks No surface undercut <1/32 in. (1.0 mm) Limits on weld reinforcement No surface lack of fusion No incomplete penetration applies when inside surface is readily accessible BECHT ENGINEERING COMPANY, INC. What s Different in B

15 Inspection, Examination and Testing BEP requires hydrotest in accordance with ASME B&PV Code, Section I Non BEP requires hydrotest or, at the owner s option, pneumatic, sensitive leak or initial service leak testing Lines open to the atmosphere do not require testing Joints must be exposed for examination during leak testing, except that insulated systems may be tested by fluid loss over time method BECHT ENGINEERING COMPANY, INC. What s Different in B Inspection, Examination and Testing Pressure must be held a minimum of 10 minutes, and then may be reduced to design pressure for leak examination period Stress during hydrotest is limited to 90% S Y, rather than 100% S Y Hydrotest pressure is 1.5 times the design pressure no temperature correction Pneumatic testing requires owner s approval Pneumatic test pressure is 1.2 to 1.5 times the design pressure BECHT ENGINEERING COMPANY, INC. What s Different in B

A Comparison: ASME B31.1 Power Piping versus ASME B31.3 Process Piping

A Comparison: ASME B31.1 Power Piping versus ASME B31.3 Process Piping Don Frikken, PE BECHT ENGINEERING COMPANY, INC. 1 Topics Discussed B31 History Scopes Organization of the Codes Bases for Allowable