NIBRA flat roof tile F 10 U

Size: px

Start display at page:

Download "NIBRA flat roof tile F 10 U"

Aldous Logan
6 years ago
Views:

1 NIBRA flat roof tile F 10 U

This makes the F 10 U the ideal tile for easy-lay roofing.

requirements than required - Twin head and side trough - Waterproof, frost-resistant, breathable

2 The NIBRA flat roof tile F 10 U. (sliding tile) The U stands for overlap and the variable covering length of 41.3 cm ± 12 mm. This makes the F 10 U the ideal tile for easy-lay roofing. New head and side troughs allow not only easy laying but also improve the rain inlet safety with a regular roof pitch of 22. The F 10 U in detail: - Pressed roof tile according to DIN/EN 1304 with far better quality requirements than required - Twin head and side trough - Waterproof, frost-resistant, breathable - Regular roof pitch 22 - Requirement per m 2 approx. 10 pcs. NIBRA tiles are manufactured from Westerwald clay in a ceramic quality. The correspondingly low water absorption of below 3 % and extreme resistance to frost are preconditions for the long life of NIBRA tiles.

green noble engobed (glazed) (matt black glazed) (Delivery period on request) (26) almond brown noble engobed

(Delivery period on request) (32) old black engobed Colour deviations: Our clay roof tiles are environment-friendly

This is often the case with naturally red tiles since the fired colour is the sole result of natural raw materials

3 The Colours. (01) natural red (02) red engobed (04) brown engobed (09) bordeaux red engobed (18) black noble engobed (20) pine green noble engobed (glazed) (matt black glazed) (Delivery period on request) (26) almond brown noble engobed (glazed) (29) bunt metallic edelengobiert (31) cobalt black noble engobed (glazed) (Delivery period on request) (Delivery period on request) (32) old black engobed Colour deviations: Our clay roof tiles are environment-friendly building materials. When using natural raw materials you may experience colour deviations. This is often the case with naturally red tiles since the fired colour is the sole result of natural raw materials with no added metal oxides to change the colour. Deviations are possible in the colours for reasons of printing methods. Clay roof tile surfaces: Minor impairments to the surface are possible due to transport. This does not affect the quality of the tiles.

4 The program. Moulded bricks for various functions meet the demand for homogeneous, architecturally demanding roofs. They are also an important safety factor. Moulded bricks and accessories reduce the amount of laying work and facilitate calculations. You will find the complete program for every tile on our Internet website Whole tile (also available with nail hole as required*) Weight: ~ 3.8 kg ~ 10.0 pcs/m 2 Double flap Width: ~ 32.4 cm Covering width: ~ 32.4 cm Weight: ~ 5.2 kg ~ 2.5 pcs/m Half tile Width: ~ 17.0 cm Covering width: ~ 11.9 cm Weight: ~ 2.6 kg Left verge tile Width: ~ 32.4 cm Covering width: ~ 24.0 cm Weight: ~ 6.3 kg ~ 2.5 pcs/m Right verge tile Width: ~ 29.2 cm Covering width: ~ 15.2 cm Weight: ~ 5.9 kg ~ 2.5 pcs/m Standard ridge tile ~ 2.7 pcs/m Length: ~ 43.5 cm Covering length: ~ 37.0 cm Width: ~ 25.1 cm Covering width: ~ 20.0 cm Weight: ~ 3.7 kg ~ 2.7 pcs/m Standard start ridge, bottom closed for verge tile with offset ridge Length: ~ 43.5 cm Covering length: ~ 30.5 cm Width: ~ 24.5 cm Covering width: ~ 20.0 cm Standard ridge end, bottom closed for verge tile with offset ridge Length: ~ 39.0 cm Covering length: ~ 31.0 cm Width: ~ 25.1 cm Covering width: ~ 20.0 cm Standard crest start Length: ~ 49.0 cm Covering length: ~ 42.0 cm Width: ~ 24.5 cm Covering width: ~ 20.0 cm Universal hip cap (also available with four outlets) Weight: ~ 4.5 kg Clay dormer ventilator (ventilation cross-section ~ 17 cm 2 ) Weight: ~ 4.2 kg Ceramic vent pipe tile with weather cap ø 150 and matching hose with adapter Ceramic aerial tile Ceramic thermal exhaust gas through pantile with universal collar (ø: max. 127 mm) (can be used up a max of 40 RP*) Length: ~ 48.7 cm Covering length: ~ 41,6 cm ± 12 mm Ridge connecting tile (left/right verge tiles also available) Length: ~ 48.7 cm Covering length: ~ 41.6 cm ± 10 mm Weight: ~ 4.2 kg Ridge tile extra ~ 2.6 pcs/m (matches ridge connecting tile) (Start and end ridge extra also available) Length: ~ 43.7 cm Covering length: ~ 38.0 cm Width: ~ 25.2 cm Covering width: ~ 21.1 cm Pent tile standard (90 ), pent tile according to custom measures (custom made tile available upon request) 1 2 Mansard tile (left/right verge tiles also available) Length: Covering length: Shed roof tile (left/right verge tiles also available) Length: Covering length: Ceramic solar through tile up to ø 70 mm ø: 70 mm Alu Solar carrier pantile** 2 Alu-walking grid tile, coated Width: ~ 34.0 cm Length: 40.0; 80.0 cm SnapStep universal alu step (40 cm and 80 cm universal walking grid with two brackets also available) coated, for mounting on different lath thicknesses, can be adjusted for roof pitches from 0-60 Alu base tile with single step Alu base pantile with twin tube holder Alu tile with round wood holder Alu tile with snow rib support Length: ~ cm Covering length: ~ 41.6 cm ± 12 mm Light tile Acrylic glass Length: ~ 48.2 cm Covering length: ~ 41.6 cm ± 12 mm Steel skylight, coated, 4-tiles, acrylic glazed Hatch: 45.0 x 55.0 cm wingopan hsv-tt-roof window incl. flashings Length ~ 78.0 cm Opening: upwards Width: ~ 55,0 cm Hatch: 47,0 x 54,0 cm Insulation glas: UG=1,0 W/m 2 K Ridge/crest lath holder Ridge or crest clip no. 470/41 for standard ridge tile Ridge or crest clip no. 470/170 for ridge tile extra Copper roll/alu roll 2000 Length: ~ 5 m, Width: ~ 29 cm, 33 cm, 36 cm Ventilation cross-section: permanent acc. to DIN 4108, Part 3 Natural copper/anthracite, red Multi storm claw Storm clip no. 456/005 for battens 30 x 50 V2A [1] Storm clip no. 456/013 for battens 40 x 60 V2A [1] Storm clip no. 409/012 V2A [2] All sizes are approx. sizes. Tolerances according to DIN EN Covering sizes are to be determined on site. Subject to technical changes. * Over 40 RP = special design of PVC on request ** Installation manual in the installati brochure or under

5 Laying the NIBRA flat roof tile F 10 U. Technical data Roof tile NIBRA flat roof tile F 10 U Manufacturer Nelskamp (D) Overall length ~ 48.7 cm Overall width ~ 29.6 cm Mean covering length ~ 41.6 cm ± 12 mm Mean covering width ~ 24.2 cm Requirement per m 2 ~ 10.0 pieces Weight per tile ~ 3.8 kg Requirement per m 2 ~ 38.0 kg Regular roof pitch 22 Storm clips: Multi storm claw Side-seam bracket (to hang in) 456/005 for battens 30 x 50 mm Side-seam bracket (to hang in) 456/013 for battens 40 x 60 mm Side seam bracket (to hit in) 409/012 Laying! The following applies for laying our concrete roofing tiles: 1. The NELSKAMP producers provisions. These can punctually deviate from the rules of the German Roofers Association and have to be applied with priority. (Installtion brochure) 2. The specialist rules of the roofing trade (rules for coverings with concrete roofing tiles) 3. The Construction Contract Procedures VOB (concrete roofing tiles) Material requirements for coverage Laths ~ 2.5 m/m 2 (incl. 10% waste) Counter-laths ~ 1.7 m/m 2 (incl. 10% waste) Roof tile ~ 10.0 pieces/m 2 Packing unit* Tiles per pallet 288 pieces Tiles per stack 36 pieces Half tile Double flap ~ 2.5 pieces/m for left side of roof only Verge tile ~ 2.5 pieces/m Walking grid pantile as required Ridge or crest tile ~ 2.7 pieces/m Copper roll/alu roll 2000 as required (5 m per roll) Ridge/crest clip 470/ piece per ridge tile standard Wood screws 1.0 piece per ridge tile d = 4.5 mm Screw depth: 24 mm Ridge or crest initial tile 1.0 piece per ridge or crest start Ridge end tile 1.0 piece per ridge end Ridge lath holder 1.0 piece per rafter Crest lath holder 1.0 piece/ ~ 70 cm Eaves fresh air element ~ 1.1 piece/m Fresh air ~ 200 cm 2 /m * only applies for deliveries in Germany Regular roof pitch for clay roof tiles Regular roof pitch flat roof tile F 10U Minimum roof pitch for roofing with clay roof tiles If the pitch is below the regular roof pitch the additional measures of the roofing trade rules must be carried out (cf. table). With equivalent roof substructure alternatives: pay attention to the manufacturer s and laying instructions. Warranty must be assumed by the relevant manufacturer. Classification of additional measures except for subordinate buildings 1) according to the technical rules of the German roofing trade Higher requirements 2) Roof Use - Design - Climatic conditions pitch no further one further two further three further increased requirement 2) increased requirement 2) increased requirement 2) 22 Class 6 Class 6 Class Underlayment 3.3 Underlayment 2.4 Overlapping / interlocking undercover (USB- A) (USB- A) (UDB- A; UDB- B 5) ) or Class Underlayment secured at seams (USB- A) Class Welded / bonded undercover 2.3 Undercover covered with bitumen sheeting 3.2 Underlayment secured at seams Class Rainproof roof substructure Class Welded / bonded undercover 2.3 Undercover covered with bitumen sheeting 3.2 Underlayment secured at seams Class Rainproof roof substructure Class Waterproof roof substructure increased requirement 2) Class Welded / bonded undercover 2.3 Undercover covered with bitumen sheeting 3.2 Underlayment secured at seams 3) Class Waterproof roof substructure MRP 10 1) The additional measures named in the table are minimum measures taking into account table 1 of the Leaflet for roof substructures, undercovers, underlays. 2) Higher requirements form categories in accordance with Section Further higher requirements may result from the weighting within a category according to Section For example, climatic conditions can lead to several higher requirements. 3) Only allowed if proof has been rendered of the functional reliability of the products used including accessories (sealing tapes, adhesive tapes, sealing compounds, ready-made seam protection, etc.) by the manufacturer during a driving rain test. The next highest class should otherwise be chosen. 4) Undercover- sheets are to be scheduled according to the classification Intruction note for under roofs, undercovers and underlayers. Producers limitations are to be fulfilled. Hints and information for the perforation securement are to be taken from the data sheets. 5) If indices 2), 3), 4), 5) in the product data sheet are met: 2) Resistance to driving rain, proven by the Driving rain test underlay and undercover sheets - TU Berlin 3) Higher requirements on ageing are proven by increasing the temperature in the test method Appendix C 5.2 of DIN EN to 80 C. 4) The manufacturer specifies the duration of the outdoor weathering period whist warranting the aforementioned properties. 5) The manufacturer confirms the suitability as a provisional cover and specifies the duration of the outdoor weathering period whist warranting the aforementioned properties.

6 Covering widths covering width left verge tile = 24.0 cm covering width double flap = 32.4 cm Roof lathing in conjunction with ridge flaps (dry ridge) Supporting laths: The following min. cross-sections must be used: (rules for roofing, notes on wood and timber materials) Nom. cross-sections Rafter intervals Sizing class of support laths (unit spacing) 30 x 50 mm 80 cm S x 60 mm 100 cm S 10 Chalk line marking lining out every 3-5 rows Eaves lath ~ 46 cm to end of rafter covering width right verge tile = 15.2 cm 72 Counter-laths: Rec. thickness of counter-laths acc. to rules for roofing (notes on wood and timber materials): Rafter length Rec. thickness up to 8 m 24 mm up to 12 m 30 mm over 12 m 40 mm 41.6 cm ± 12 mm Mean covering length 41.6 cm ± 12 mm tiefhängende Rinne: Rafter length X Distance upper support lath to ridge crown (see table) RP 30 > > 45 X ~ 30 mm ~ 25 mm ~ 20 mm The dimensions are planning figures and should be checked before laying. Details eaves design The dimensions are planning figures and should be checked before laying depending on the design and local circumstances. 1 With gutter & vent element 2 High-level gutter (recommended for flat roof pitches < 22 ) Tile overhang in gutter max. 1/3 of gutter width Eaves lath ~ 46 cm to end of rafter Eaves lath ~ 38 cm to end of rafter Vent element Eaves plate Fresh air Drip plate Ridge/crest details Verge details Ridge/crest clip No. 470/41 The height of the ridge/crest lath is determined by the customer. Nominal cross-section at least 24 x 48 mm tiefhängende Rinne: 0,6 kn/m Each ridge tile: wood screw, d = 4.5 mm screw depth: 24 mm Copper roll/alu roll 2000: Rec. for ridge flap band width 290 mm (narrow undercover) Rec. for ridge flap band width 330 mm (broad undercover) 0,6 kn/m Each verge tile: wood screw, d = 4.5 mm screw depth: 24 mm Also applies for the double flap! The screw connection in the verge should have a permanently elastic seal particularly for flat roof pitches (e.g. plumber screws) Ridge lath holder Ridge tiles should be fastened to the furring. 1 wood screw and 1 clip The distance between inner edge of the verge shield to the outer edge of the exterior wall / cladding must be min. 1cm. (The overhang of double lip stones or stones reaching over the outer edge of the gable wall / cladding or sub-structure must be min. 3cm.)

Pent tile standard (90 ), pent tile according to custom measures (custom made tile available upon request) Size sheets can be downloaded from the Internet Pent roof tiles should be fastened to the

Lath distance 330 mm Wide verge shield 110 mm Aeration and ventilation in steep roof 1 Eaves fresh air element 2 Copper roll/alu roll 2000 3 Clay dormer ventilator with fitted screen vent

Covering length: ~ 41.6 cm ± 12 mm Roof lath 30/50 Covering length: ~ 41.6 cm ± 12 mm 1) The vent cross-section at the eaves should be at least 200 cm 2 /m of eaves.

7 Pent tile standard (90 ), pent tile according to custom measures (custom made tile available upon request) Size sheets can be downloaded from the Internet Pent roof tiles should be fastened to the furring (see detail verge). Lath distance 330 mm Wide verge shield 110 mm Aeration and ventilation in steep roof 1 Eaves fresh air element 2 Copper roll/alu roll Clay dormer ventilator with fitted screen vent cross-section ~ 17 cm Aeration/venting Counter-laths Underlay/undercover sheet Eaves fresh air element Laying instructions for ridge connecting tile (with ridge tile extra) Roof lath 40/60 Covering length: ~ 41.6 cm ± 12 mm Roof lath 30/50 Covering length: ~ 41.6 cm ± 12 mm 1) The vent cross-section at the eaves should be at least 200 cm 2 /m of eaves. 2) The vent cross-section at the ridge or crest should be at least 0.5 of the total corresponding roof area, though at least 50 cm 2. (according to DIN ) Wall connection tile Size sheets can be downloaded from the Internet 2 Mansard and shed roof tile Size sheets can be downloaded from the Internet A D Ridge design with ridge connecting tiles Upper edge 1st lath from ridge crown up to 30 RP Laths 30 x 50 mm 6.0 cm up to 30 RP Laths 40 x 60 mm 5.0 cm up to 45 RP Laths 30 x 50 mm 5.5 cm up to 45 RP Laths 40 x 60 mm 4.5 cm over 50 RP Laths 30 x 50 mm 5.5 cm over 50 RP Laths 40 x 60 mm 4.5 cm The dimensions are planning figures and should be checked before laying. Installation instructions for universal alu step A chase is made in the head and foot interlocking joint of the gutter tile using a right angle grinder with diamond wheel to lead through the stainless steel suspension hinge. Hang the alu mounting bracket in the throat of the gutter tile so that the two rubber profiles with the lower end of the mounting bracket lie on the roof lath. The rubber profiles must rest where the gutter tiles overlap. Installation instructions on delivery Installation instructions for alu base pantile with single step/walking grid pantile/snow stop tile Of stainless steel/aluminium. No supporting laths needed! Fastening to supporting lath: Aluminium tile fastened to lath with 2 screws (V2A screw included) Horizontal orientation from 0-60 roof inclination possible Processing acc. to DIN Article 45 > 45 Walking grid every every tile row of tiles row of tiles Alu base tile every every w step tile row of tiles row of tiles tested to DIN EN 516 Mounting bracket Stainless steel suspension hinge can be adjusted for roof pitches from 0-60 Roof lath 2 x fastening in the counter-lath The same applies for alu pantiles with snow rib or round wood holder, whereby the max. support spacing should not exceed 90 cm. For higher demands you should reduce the support spacing (60 cm). Step tested to DIN EN 516 Storm clips Multi storm claw As a download on the Internet from Product specifications Laying instructions CAD data 1 Multi storm claw B No. 456/ x 50 V2A No. 456/ x 60 V2A C No. 409/012 V2A According to professional standards, we can supply storm clips for a simple and effective protection against wind suction. They can alternatively be clipped to the laths or knocked into the laths. Resistant to corrosion through stainless steel wire (A2) or ZIAL coating (corrosion protection). E That s new: Maximum protection against wind suction and easy installation: The multi storm claw is placed on top of the gutter tile at the appropriate point and screwed to the laths. The roof tiles remain completely free of screw holes that could impair their function. There is a clay groove pressed into the underside of the tile where the multi storm claw can be clipped into place. After screwing into place the next overlapping tile is simply laid in position. The multi storm claw audibly clips/grips the clay groove after a slight pressure is exerted on the tile. The multi storm claw ensures a combined (2-fold) fastening of the roof tile at its top and bottom. The pull-out values of former common side rabbet clips are greatly exceeded. The tiles are fastened in place absolutely stormproof in accordance with the technical rules for roofing. F Subject to technical changes. The dimensions are planning figures and should be checked before laying.

LONGLIFE matt CLIMALIFE concrete roofing tiles With their ClimaLife surface our roof pantiles clean our environment from contaminants resulting from heating, traffic and the industry.

8 For colourful, clean roofs. The Nelskamp concrete roofing tile program. S pantile TOP 2000 S, LONGLIFE gloss and CLIMALIFE Sigma pantile TOP 2000 S, LONGLIFE matt Finkenberger pantile TOP 2000 S, LONGLIFE gloss and CLIMALIFE Kronen pantile LONGLIFE matt Planum pantile LONGLIFE matt CLIMALIFE concrete roofing tiles With their ClimaLife surface our roof pantiles clean our environment from contaminants resulting from heating, traffic and the industry. Up to 90 percent are neutralized in daylight, without sunlight up to 70 percent. This is due to the titanium oxide content in the micro concrete. It mainly converts nitrogen oxides (NO X ) into harmless substances like NO 3 -. Again and again, because titanium oxide is a catalyst, which is never used up. The rain does the rest: It just flushes away the substances, which then are harmless. Conrete roof tiles LONGLIFE Slick - including the front edge: The fine surface of the LONGLIFE concrete roof tiles enables Nelskamp roofs a bright and shiny future. Due to the further development of the LONGLIFE technology also the visible front edge is now free of pores and therefore the complete roof area is long-term protected - for an optically harmonic roof. LONGLIFE concrete roof tiles stay clean for a long time - always as freshly tiled. Dirt, algae and moss hardly find grip and the rain becomes a shower for the roof. The new coating delivers bright shining results - and that in two grades of gloss: depending on the model the LONGLIFE conrete roof tiles are available in matt and glossy. Durably clean. Durably constant in colour. Durably resistant to ambient influences. LONGLIFE. TOP 2000 S concrete roofing tiles High-quality raw materials, the latest production methods and established coating technologies with numerous standard and special colours are characteristic of TOP 2000 S concrete roofing tiles. Concrete roofing tiles and clay roof tiles from Nelskamp. The obvious solution. Our strategically placed production facilities guarantee that our roof building materials are always well received. Six plants throughout Germany are the sound, logistical basis for co-operation and help spare the environment. Administration and sales Waldweg 6 D Schermbeck Postfach D Schermbeck Phone: / Fax: / vertrieb@nelskamp.de Internet: Production of concrete roofing tiles Gartrop Works Gahlener Straße 158 D Hünxe-Gartrop Phone: / /32 Fax: /45 59 Dieburg Works Lagerstraße 30 D Dieburg Phone: / Fax: /16 73 Schönerlinde Works Schönerlinder Bahnhofstraße 6 D Wandlitz Phone: / Fax: / Production of clay roof tiles Schermbeck Works Waldweg 6 D Schermbeck Phone: / /17 Fax: /26 70 Unsleben Works Wechterswinkler Straße 23 D Unsleben Phone: / Fax: /7 49 Groß-Ammensleben Works Magdeburger Straße 42 D Groß-Ammensleben Phone: /88-6 Fax: / Last revised 05/2013

Flat roof tile F 12 U - South

Flat roof tile F 12 U - South The flat roof tile F 12 U - South. The new head and side trough in the F 12 U - South flat roof tile allows a variable height overlap of 4 cm. With approx. 11.7 to 13.0 pcs.