HILTI FIRESTOP MORTAR CFS-M RG. European Technical Assessment ETA N o 12 / 0101

Transcription

1 HILTI FIRSTOP MORTAR FS-M RG uropean Technical Assessment TA N o 12 / 0101

2 HILTI FIRSTOP MORTAR FS-M RG APPLIATIONS Mixed penetrations in rigid walls and floors from 150 mm ables, cable bundles, cable trays and cable conduits Non-combustible (metal) pipes with non-combustible insulation Non-combustible (metal) and composite pipes with combustible insulation in combination with firestop bandage FS-B ombustible (PV-U and P) pipes in combination with firestop collar FS-, firestop collar FS- P or firestop wrap FS-W Technical ata Mix ratio (Mortar to Water by Weight) Max. compressive strength after 28 days Working time Shelf life (@73 F / 23 and 50% relative humidity) Application temperature range Application temperature range (Imperial) 2.5:1 2.9 N / mm² 45 min 12 month(s) F 176 F AVANTAGS asy to install with trowel or commercially available pumps thanks to adjustable consistency xcellent thermal insulating properties No shrinkage during curing or in the event of fire Paintable Assessments T2 / 0101 Base materials oncrete, aerated concrete and masonry Reaction to fire class lass A1 according to N The uropean Technical Assessment (TA) and the technical data sheet can be obtained via your local Hilti contact. Order designation Sales quantity Item number Firestop mortar FS-M RG 1 P

3 INSTALLATION INSTRUTIONS 1 lean and pre-moisten surfaces. ables and supporting structures must be dry and clean of dust, grease or oil and installed in compliance with local building and electrical standards. 2 Add Hilti Firestop Mortar FS-M RG to water in a ratio of approximately 2.5 : 1 (mortar to water by weight). The mix ratio of Hilti Firestop Mortar to water determines the desired consistency (stiffness) Stir the mixture thoroughly with, for example, a Hilti T-MP paddle. Large volumes of Hilti Firestop Mortar may be mixed using commercially available mixing or plastering machines. o not use any other binders or additives. 4 Place forms on one or both sides of large openings. Floor openings must have formwork underneath. Apply mixed mortar in the opening using a trowel or pump and compact it. nsure that all gaps and spaces are completely filled and closed. Smooth the surface as with standard concrete. 5 Ausführungsschild epending on the application and fire rating to be achieved, additional protection (e.g. mineral wool mat) may be required (see TA for details). For installation of additional components (e.g. Hilti Firestop ollar FS- P and Hilti Firestop Bandage FS-B) see TA. If required by national prescriptions mark the penetration seal with an identification plate containing the required information. In such a case fasten the identification plate in a visible position next to the seal. 03

4 ABL PNTRATION, PIP PNTRATION RIGI WALL The intended use of Hilti firestop mortar FS-M RG is to reinstate the fire resistance of: Rigid walls (), minimum thickness 150 or 175 mm (t ), concrete, aerated concrete or masonry, minimum density of 550 or 1100 kg / m 3. All penetrating items (cables, cable trays, conduits, metal pipes and plastic pipes) can be installed as a single, multiple or mixed configuration. Maximum seal size (width height) 1200 mm 2000 mm respectively 1000 mm 1500 mm depending on wall thickness. Minimum distances between penetrants and seal edges to be considered. ABLS, ABL BUNLS, ABL TRAYS AN ONUITS Additional protection epending on the required fire resistance, additional protection (AP) may be required. AP: mineral wool mat, wrapped around cables / cable support (trays, ladders), Al-faced side outside, fixed with wire, width (length along the cables LAP) 200 mm, thickness (tap) 30 mm. Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity Without additional protection (AP) With additional protection (AP) All sheathed cables up to 21 mm diameter I 120 I 120 All sheathed cables up to 80 mm diameter I 90 I 120 All non-sheathed cables max. diameter 24 mm I 30 I 120 Tied cable bundle max. diameter 100 mm with max. diameter of single cable 21 mm Plastic conduits and tubes 16 mm with or without cables or cable supports Steel conduits and tubes 16 mm with or without cables or cable supports Rigid Wall 150 mm minimum density of 550 kg / m 3 I 120 I 120 I 180-U / I 180- / U In case a conduit is installed with open ends on both sides (U / U), conduit must be closed with e.g. Hilti Firestop Acrylic Sealant FS-S AR. able penetrations without add. protection able penetrations with additional protection (AP) t t w A1 3 A1 AP 3 AP h tap ta1 LAP LAP A 1 ta1 t t w 2 AP 2 AP h t AP A 1 1 L AP L AP 1 04

5 MTAL PIPS WITH MINRAL WOOL INSULATION Penetration seal (A) / services () Wall type and thickness (t ) Insulation thickness (t ) lassification = Integrity Steel pipes mm diameter, pipe wall thickness 2.2 / mm Steel pipes mm diameter, pipe wall thickness 2.9 / mm 20 mm 40mm I 120- / U With continued insulation (), sustained Steel pipes mm diameter, pipe wall thickness 2.2 / mm Steel pipes 76.0 mm diameter, pipe wall thickness mm 20 mm 40 mm I 120- / U L 500 mm, sustained Steel pipes mm diameter, pipe wall thickness 2.9 / mm 40 mm I 90- / U Steel pipes mm diameter, pipe wall thickness mm Steel pipes mm diameter, pipe wall thickness mm Rigid Wall 150 mm minimum density of 550 kg / m 3 40 mm I 120- / U 40 mm I 120- / U With continued insulation (), interrupted L 800 mm, interrupted opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes mm diameter, pipe wall thickness 1.5 / mm 20mm 40 mm I 120- / U With continued insulation (), sustained opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes 54 mm diameter, pipe wall thickness mm 20 mm 40 mm I 120- / U L 500 mm, sustained opper pipes mm diameter, pipe wall thickness 1.5 / mm 40 mm L 800 mm, sustained ontinued insulation, sustained Local insulation, sustained t t t A1 t t A1 t d d ta1 L ta1 ontinued insulation, interrupted Local insulation, interrupted t t t A1 t t A1 t d d ta1 L ta1 05

6 MTAL PIPS WITH ARMAFLX AF INSULATION Steel, cast iron, stainless steel, Ni alloys (Niu, Nrr, NiMO alloys), copper pipes. With Hilti firestop bandage FS-B (A2), two layers wrapped around pipe insulation on each side of the seal. Penetration seal (A) / services () Wall type and thickness (t ) Insulation thickness (t ) lassification = Integrity Metal pipes, mm diameter, pipe wall thickness 2.2 / mm Metal pipes, mm diameter, pipe wall thickness 2.9 / mm 19 / mm 41 mm I 120- / U With continued insulation (), sustained Metal pipes, mm diameter, pipe wall thickness 2.2 / mm Metal pipes, mm diameter, pipe wall thickness 2.9 / mm opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes mm diameter, pipe wall thickness 1.5 / mm Rigid Wall 150 mm minimum density of 550 kg / m 3 19 / mm I 120- / U 41 mm I 60- / U mm I 120- / U 41 mm L 500 mm, sustained With continued insulation (), sustained opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes mm diameter, pipe wall thickness 1.5 / mm 19 / mm L 500 mm, sustained I 120- / U 41 mm L 800 mm, sustained ontinued insulation, sustained Local insulation, sustained t t t t t t d d A 2 L A 2 06

7 MTAL PIPS WITH ARMAFLX AF INSULATION Steel, cast iron, stainless steel, Ni alloys (Niu, Nrr, NiMO alloys), copper pipes. Additional protection: Armaflex AF, thickness 25 mm over a length of 200 mm from the seal on both sides. Penetration seal (A) / services () Wall type and thickness (t ) Insulation thickness (t ) lassification = Integrity Metal pipes, mm diameter, pipe wall thickness mm Metal pipes, mm diameter, pipe wall thickness mm Rigid Wall 150 mm minimum density of 550 kg / m 3 25 mm With continued insulation (), interrupted I 120- / U 25 mm L 780 mm, interrupted ontinued insulation, interrupted Local insulation, interrupted t t AP AP t t AP t t t AP t d d L AP L AP L L AP L AP 07

8 PLASTI PIPS With Hilti firestop collar FS- P PV-U pipes according to N ISO 1452, N ISO and IN 8061 / 8062 Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness mm I 120-U / U 63 mm, pipe wall thickness mm I 120-U / U 75 mm, pipe wall thickness mm I 180-U / U 90 mm, pipe wall thickness mm I 120-U / U 110 mm, pipe wall thickness mm Rigid Wall 150 mm minimum density of 550 kg / m 3 I 120-U / U 110 mm, pipe wall thickness 8.1 mm I 180-U / U 125 mm, pipe wall thickness mm I 120-U / U With Hilti firestop collar FS- P (A 3 ) on both sides of the seal, fixed together by M8 threaded rods, washers and nuts. Always use the appropriate collar size and number of hooks for the different pipe diameters. 160 mm, pipe wall thickness mm I 120-U / U 160 mm, pipe wall thickness 11.8 mm I 180-U / U P pipes according to N ISO 15494, IN 8074 / 8075 Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 2.9 mm I 180-U / U 50 mm, pipe wall thickness mm I 120-U / U 63 mm, pipe wall thickness mm I 90-U / U 63 mm, pipe wall thickness mm I 120-U / U 75 mm, pipe wall thickness mm 90 mm, pipe wall thickness mm Rigid Wall 150 mm minimum density of 550 kg / m 3 I 120-U / U I 120-U / U 110 mm, pipe wall thickness mm I 120-U / U With Hilti firestop collar FS- P (A 3 ) on both sides of the seal, fixed together by M8 threaded rods, washers and nuts. Always use the appropriate collar size and number of hooks for the different pipe diameters. 125 mm, pipe wall thickness mm I 120-U / U 160 mm, pipe wall thickness mm I 120-U / U 160 mm, pipe wall thickness 9.1 mm I 180-U / U P pipes according to N ISO Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 3.0 mm I 120-U / U 63 mm, pipe wall thickness 3.0 mm I 180-U / U 75 mm, pipe wall thickness 3.0 mm I 120-U / U 90 mm, pipe wall thickness 3.5 mm Rigid Wall 150 mm minimum density of 550 kg / m 3 I 180-U / U 110 mm, pipe wall thickness 4.2 mm I 120-U / U 125 mm, pipe wall thickness 4.8 mm I 120-U / U With Hilti firestop collar FS- P (A 3 ) on both sides of the seal, fixed together by M8 threaded rods, washers and nuts. Always use the appropriate collar size and number of hooks for the different pipe diameters. 160 mm, pipe wall thickness 6.2 mm I 120-U / U 08

9 PLASTI PIPS With Hilti firestop collar FS- PV-U pipes according to N ISO 1452, N ISO 15493, IN 8061 / 8062 Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 2.2 mm 110 mm, pipe wall thickness mm Rigid Wall 150 mm minimum density of 550 kg / m 3 I 180-U / With Hilti firestop collar FS- (A 3 ) on both sides of the seal, fixed together by M8 threaded rods, washers and nuts. Always use the appropriate collar size and number of hooks for the different pipe diameters. Plastic pipes t t d A 3 09

10 PLASTI PIPS With Hilti firestop wrap FS-W Hilti firestop wrap FS-W (A 4 ) on both sides of the mortar seal, flush with the surface of the seal. PV pipes according to N ISO 1452, N ISO 15493, IN 8061 / 8062 Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 32 mm, pipe wall thickness 1.8 mm FS-W L 1 layer 90 mm, pipe wall thickness 3.2 mm FS-W SG 110 mm, pipe wall thickness 3.2 mm FS-W SG Rigid Wall 175 mm, minimum I 240-U / density of 1100 kg / m 3 > mm, pipe wall thickness 3.2 mm FS-W L 2 layers 160 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 3 layers P pipes according to N ISO 15494, IN 8074 / 8075 Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 32 mm, pipe wall thickness 1.8 mm FS-W L 1 layer 90 mm, pipe wall thickness 2.7 mm FS-W SG 110 mm, pipe wall thickness 2.7 mm FS-W SG Rigid Wall 175 mm, minimum I 240-U / density of 1100 kg / m 3 > mm, pipe wall thickness 2.7mm FS-W L 2 layers 160 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 3 layers P pipes according to N Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity 160 mm, pipe wall thickness 6.2 mm FS-W SG Rigid Wall 175 mm, minimum I 180-U / density of 1100 kg / m 3 > mm, pipe wall thickness 6.2 mm FS-W L 3 layers Plastic pipes t A1 A 4 t d 10

11 ABL PNTRATION, PIP PNTRATION Rigid floors The intended use of the Hilti firestop mortar FS-M RG is to reinstate the fire resistance of: Rigid floors (), minimum thickness 150 or 175 mm (t ), concrete or aerated concrete, minimum density of 550 or 2400 kg / m 3. All penetrating items (cables, cable trays, conduits, metal pipes and plastic pipes) can be installed as a single, multiple or mixed configuration. Maximum opening sizes as well as minimum distances between penetrants and seal edges to be considered. ABLS, ABL BUNLS, ABL TRAYS AN ONUITS Additional protection epending on the required fire resistance, additional protection (AP) may be required. AP: mineral wool mat, wrapped around cables / cable support (trays, ladders), Al-faced side outside, fixed with wire, width (length along the cables) 200 mm, thickness 30 mm. Penetration seal (A) / services () Wall type and thickness (t ) lassification = Integrity Other criteria, description Without additional protection (AP) Without additional protection (AP) With additional protection (AP) 200 mm seal thickness 150 mm seal thickness All sheathed cables up to 21 mm diameter I 90 I 90 I 90 All sheathed cables up to 80 mm diameter I 90 I 60 I 90 All non-sheathed cables up to 17 mm diameter I 90 I 45 I 90 All non-sheathed cables up to 24 mm diameter Rigid Floor I 45 I 45 I 60 Tied cable bundle max. diameter 100 mm 150 mm with max. diameter of single cable 21 mm minimum density of 550 kg / m 3 I 90 I 90 I 90 Plastic conduits and tubes 16 mm with or without cables or cable supports Steel conduits and tubes 16 mm with or without cables or cable supports I 120-U / I 90-U / I 90-U / I 120- / U I 90- / U I 90- / U In case a conduit is installed with open ends on both sides (U / U), conduit must be closed with e.g. Hilti Firestop Acrylic Sealant FS-S AR. 11

12 able penetrations without add. protection able penetrations with additional protection (AP) t AP w L AP AP AP t t l 3 3 A 1 L AP t AP AP w t t AP l A 1 Seal type with 200 mm seal thickness d d ta1 d d t t

13 MTAL PIPS WITH MINRAL WOOL INSULATION Steel, cast iron, stainless steel, Ni alloys (Niu, Nrr, NiMO alloys), copper pipes. No additional protection (AP). Penetration seal (A) / services () Floor type and thickness (t ) Insulation thickness (t ) lassification = Integrity Steel pipes mm diameter, pipe wall thickness 2.2 / mm Steel pipes mm diameter, pipe wall thickness 2.9 / mm 20 mm 40 mm I 120- / U With continued insulation (), sustained Steel pipes mm diameter, pipe wall thickness 2.2 / mm Steel pipes 76.0 mm diameter, pipe wall thickness mm 20 mm 40 mm I 120- / U L 500 mm, sustained Steel pipes mm diameter, pipe wall thickness 2.9 / mm opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes mm diameter, pipe wall thickness 1.5 / mm Rigid Floor 150 mm minimum density of 550 kg / m 3 40 mm 20 mm 40 mm I 120- / U L 700 mm, sustained With continued insulation (), sustained opper pipes mm diameter, pipe wall thickness 1.0 / mm opper pipes 54 mm diameter, pipe wall thickness mm 20 mm 40 mm I 120- / U L 500 mm, sustained opper pipes mm diameter, pipe wall thickness 1.5 / mm 40 mm L 800 mm, sustained Metal pipes, mm diameter, pipe wall thickness mm Metal pipes, mm diameter, pipe wall thickness mm Rigid Floor 150 mm, minimum density of 2400 kg / m 3 40 mm 40 mm I 120- / U With continued insulation (), interrupted L 800 mm, interrupted ontinued insulation, sustained Local insulation, sustained t t L t t t t d d ontinued insulation, sustained Local insulation, interrupted t t L t t t t d d 13

14 MTAL PIPS WITH ARMAFLX AF INSULATION Steel, cast iron, stainless steel, Ni alloys (Niu, Nrr, NiMO alloys), copper pipes. With Hilti firestop bandage FS-B (A2), two layers wrapped around pipe insulation on each side of the seal. Penetration seal (A) / services () Floor type and thickness (t ) Insulation thickness (t ) lassification = Integrity Metal pipes, 26.7 mm diameter, pipe wall thickness mm 19 mm I 120- / U Metal pipes, mm diameter, pipe wall thickness 2.2 / mm Metal pipes, 76.0 mm diameter, pipe wall thickness mm mm I 90- / U 41 mm I 120- / U With continued insulation (), sustained Metal pipes, mm diameter, pipe wall thickness 2.9 / mm 41 mm I 90- / U Metal pipes, 26.7 mm diameter, pipe wall thickness mm 19 mm I 120- / U Metal pipes, mm diameter, pipe wall thickness 2.2 / mm mm I 90- / U L 500 mm, sustained Metal pipes, 76.0 mm diameter, pipe wall thickness mm 41 mm I 120- / U Metal pipes, mm diameter, pipe wall thickness 2.9 / mm Rigid Floor 150 mm minimum density of 550 kg / m 3 41 mm I 90- / U L 700 mm, sustained opper pipes 28 mm diameter, pipe wall thickness mm 19 mm I 120- / U opper pipes mm diameter, pipe wall thickness 1.0 / mm mm I 90- / U With continued insulation (), sustained opper pipes mm diameter, pipe wall thickness 1.5 / mm 41 mm I 120- / U opper pipes 28 mm diameter, pipe wall thickness mm 19 mm I 120- / U opper pipes mm diameter, pipe wall thickness 1.0 / mm mm I 90- / U L 500 mm, sustained opper pipes 54 mm diameter, pipe wall thickness mm opper pipes mm diameter, pipe wall thickness 1.5 / mm 41 mm 41 mm I 120- / U L 800 mm, sustained ontinued insulation, sustained Local insulation, sustained t t A 2 L A 2 A1 t t t t d d 14

15 MTAL PIPS WITH ARMAFLX AF INSULATION Steel, cast iron, stainless steel, Ni alloys (Niu, Nrr, NiMO alloys), copper pipes. Additional protection: Armaflex AF, thickness 25 mm over a length of 200 mm from the seal on the top side of the floor. Penetration seal (A) / services () Floor type and thickness (t ) Insulation thickness (t ) lassification = Integrity Metal pipes, mm diameter, pipe wall thickness mm Metal pipes, mm diameter, pipe wall thickness mm Rigid Floor 150 mm, minimum density of 2400 kg / m 3 25 mm 25 mm I 180-U / With continued insulation (), interrupted L 800 mm, interrupted ontinued insulation, interrupted Local insulation, interrupted t t t AP t AP AP L AP L AP L AP t t t t d d 15

16 PLASTI PIPS With Hilti FS- P firestop collar PV-U pipes according to N ISO 1452, N ISO and IN 8061 / 8062 Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness mm 63 mm, pipe wall thickness mm 75 mm, pipe wall thickness mm 90 mm, pipe wall thickness mm 110 mm, pipe wall thickness mm Rigid Floor 150 mm minimum density of 550 kg / m 3 I 120-U / U With Hilti firestop collar FS- P (A 3 ) fixed on the underside of the seal. Always use the appropriate collar size and number of hooks for the different pipe diameters. 125 mm, pipe wall thickness mm 160 mm, pipe wall thickness mm P pipes according to N ISO 15494, IN 8074 / 8075 Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness mm 63 mm, pipe wall thickness mm 75 mm, pipe wall thickness mm 90 mm, pipe wall thickness mm 110 mm, pipe wall thickness mm Rigid Floor 150 mm minimum density of 550 kg / m 3 I 120-U / U With Hilti firestop collar FS- P (A 3 ) fixed on the underside of the seal. Always use the appropriate collar size and number of hooks for the different pipe diameters. 125 mm, pipe wall thickness mm 160 mm, pipe wall thickness mm P pipes according to N ISO Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 3.0 mm 63 mm, pipe wall thickness 3.0 mm 75 mm, pipe wall thickness 3.0 mm 90 mm, pipe wall thickness 3.5 mm 110 mm, pipe wall thickness 4.2 mm Rigid Floor 150 mm minimum density of 550 kg / m 3 I 120-U / U With Hilti firestop collar FS- P (A 3 ) fixed on the underside of the seal. Always use the appropriate collar size and number of hooks for the different pipe diameters. 125 mm, pipe wall thickness 4.8 mm 160 mm, pipe wall thickness 6.2 mm 16

17 PLASTI PIPS With Hilti firestop collar FS- PV-U or PV- pipes according to N ISO 15493, N ISO 1452, IN 8061 / 8062, N , N and N Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 2.0 mm 110 mm, pipe wall thickness mm Rigid Floor 150 mm, minimum density of 2400 kg / m 3 I 180-U / With Hilti firestop collar FS- (A 3 ) fixed on the underside of the seal. Always use the appropriate collar size and number of hooks for the different pipe diameters. Plastic pipes t A 3 t d 17

18 PLASTI PIPS With Hilti firestop wrap FS-W Hilti firestop wrap FS-W (A 4 ) on the underside of the mortar seal flush with the lower surface of the mortar seal. PV-U pipes according to N ISO 1452, N ISO 15493, IN 8061 / 8062 Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 32 mm, pipe wall thickness 1.8 mm FS-W L 1 layer 50 mm, pipe wall thickness mm FS-W SG 63 mm, pipe wall thickness mm FS-W SG 75 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 1 layer I 120-U / 90 mm, pipe wall thickness mm FS-W SG 110 mm, pipe wall thickness mm > mm, pipe wall thickness mm Rigid Floor 175 mm, minimum density of 2400 kg / m 3 FS-W SG FS-W L 2 layers 125 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 2 layers 160 mm, pipe wall thickness mm FS-W SG I 60-U / > mm, pipe wall thickness mm FS-W L 3 layers 160 mm, pipe wall thickness mm FS-W SG I 120-U / > mm, pipe wall thickness mm FS-W L 3 layers P pipes according to N ISO 15494, IN 8074 / 8075 Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 32 mm, pipe wall thickness 1.8 mm FS-W L 1 layer 50 mm, pipe wall thickness mm FS-W SG 63 mm, pipe wall thickness mm FS-W SG 75 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 1 layer 90 mm, pipe wall thickness mm FS-W SG Rigid Floor 175 mm, minimum I 120-U / density of 2400 kg / m mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 2 layers 125 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 2 layers 160 mm, pipe wall thickness mm FS-W SG > mm, pipe wall thickness mm FS-W L 3 layers 18

19 P pipes according to N Penetration seal (A) / services () Floor type and thickness (t ) lassification = Integrity 50 mm, pipe wall thickness 3.0 mm FS-W SG 63 mm, pipe wall thickness 3.0 mm FS-W SG 75 mm, pipe wall thickness 3.0 mm FS-W SG 75 mm, pipe wall thickness 3.0 mm FS-W L 1 layer 90 mm, pipe wall thickness 4.8 mm FS-W SG Rigid Floor 175 mm, minimum I 120-U / density of 2400 kg / m mm, pipe wall thickness 4.8 mm FS-W SG 125 mm, pipe wall thickness 4.8 mm FS-W SG > mm, pipe wall thickness 4.8 mm FS-W L 2 layers 160 mm, pipe wall thickness 6.2 mm FS-W SG > mm, pipe wall thickness 6.2 mm FS-W L 3 layers Plastic pipes t A 4 t d 19

20 Specification for mineral wool products suitable for being used as additional protection (AP) for cables / cable supports: Stone wool according to N 14303, reaction to fire class according to N A1 or A2, thermal conductivity at W / (mk), density kg / m 3, surface faced with aluminum foil on one side. The following list contains suitable products but may not be exhaustive: Isover Ultimate U TFA 34 Knauf Lamella Forte LLMF AluR Paroc Lamella Mat 35 Alu oat Rockwool Klimafix, Klimarock or 133 (Lamella mat) Specification for mineral wool products suitable for being used as pipe insulation: Sustained insulation: Isover oquilla AT-LR, Protect 1000 S alu, Protect BSR 90 alu. Paroc Section Aluoat T Rockwool onlit Pipe sections, Klimarock, RS 800 pipe sections Interrupted insulation: Stone wool acc. to N 14303, class A2 or A1 acc. to N , Al-faced Specification for flexible elastomeric foam (FF) products suitable for being used as pipe insulation: Armacell International GmbH Armaflex AF ( marked acc. to N 14304) 20

21 HARATRISTIS OF FS-M RG Additional Attributes Hilti firestop products are comprehensively tested and individually matched to the technical requirements of a building s mechanical and electrical installations. In addition to their superior passive fire protection behavior, Hilti firestop products also meet increasingly significant requirements in building technology and also help designers and installers to meet these additional requirements. The assessment of fitness for use has been made in accordance with OTA TAG No 026 Part 2. haracteristics Assessment of characteristics Norm, standard, test Health and the environment Air and gas permeability (gas tightness) angerous substances Protection against noise (air-borne sound insulation) Safety in use Mechanical resistance and stability Resistance to impact / movement / adhesion nergy, economy and heat retention Thermal properties lectrical properties urability and serviceability Gas permeability with the gases air, nitrogen (N 2 ), carbon dioxide (O 2 ) and H 4 (methane) with specific flow rates. See TA for detailed results. oes not contain dangerous substances from the list of the uropean ommission above the acceptable limits. Weighted element-normalized level difference: n,w = 59dB Weighted sound reduction index R w = 52dB Safety in use: Internal walls: Highest risk zone type has been fulfilled (Type IV). For floors: soft body impact energy 600 Nm, hard body impact energy 10 Nm Serviceability: soft body impact energy 120 Nm, hard body impact energy 6 Nm Heat conductivity (λ 10, calculated): W / mk. Volume resistivity: ± 50+10Ωcm. Surface resistivity: ± 80+08Ω. ategory Y 1,( 5 / +70) (suitable for pe netration seals intended for use at temperatures between 5 and +70 with no exposure to rain. N 1026 Material safety data sheet N ISO N ISO OTA Technical Report TR001 A.1 and A.4 N IN I 93 (V 0303 Part 30): OTA Technical Report TR 024 TAG Reaction to fire lass A1 N SRVI With more than 20 years of experience worldwide, Hilti is one of the world s leading suppliers of firestop systems. We actively help you manage your firestop projects better by providing: Quick engineering judgments xtensive technical literature On-site training and demonstrations Sophisticated jobsite logistics Assurance of conformity with specific application requirements International network of Hilti firestop specialists Our network of experienced sales representatives, field engineers, firestop specialists and customer service representatives is just a phone call away (use the local toll-free Hilti number). 21

22 22

23 23

24 Hilti orporation 9494 Schaan, Liechtenstein P / hiltigroup Hilti = registered trademark of Hilti orp., Schaan W en 2 Printed in Liechtenstein 2017 Right of technical and programme changes reserved S.. & O.