COMcheck Software Version Interior Lighting Compliance Certificate

Transcription

1 COMcheck Software Version Interior Lighting Compliance Certificate Project Information Energy Code: Project Type: 2012 IECC New Construction Construction Site: 224 First Ave Eaton, CO Additional Efficiency Package Owner/Agent: Designer/Contractor: Lawrence Smith SRB Consulting Engineering, LLC 312 Cullison Ridge Rd Windsor, CO Reduced interior lighting power. Requirements are implicitly enforced within interior lighting allowance calculations. Allowed Interior Lighting Power A Area Category B Floor Area (ft2) C Allowed Watts / ft2 D Allowed Watts (B X C) 1-Municipal Rooms (Courthouse) Total Allowed Watts = 4169 Proposed Interior Lighting Power A Fixture ID : Description / Lamp / Wattage Per Lamp / Ballast B Lamps/ Fixture C # of Fixtures D Fixture Watt. E (C X D) 1-Municipal Rooms (Courthouse) LED 1: A: 6" LED Recessed Can: Other: LED 2: B: 4" LED Recessed Can: Other: LED 3: C: 4' LED Strip Light: Other: LED 4: D: 2x4 Volumetric Troffer: Other: LED 5: E: Decorative LED Pendant: Other: LED 6: F: 6" LED Wall Washer: Other: LED : G23: 23' LED Tape Light: Other: LED 8: P16: 16' LED Direct/Indirect Pendant: Other: Track lighting 1: T8: 8' Track, LED Heads, 60W Limite: Wattage based on current limiting device capacity Track lighting 2: T12: 8' Track, LED Heads, 60W Limite: Wattage based on current limiting device capacity Linear Fluorescent 1: (E): Existing 2x4, 3-Lamp Parabolic: 48" T8 32W: Electronic: Linear Fluorescent 2: (R): Relocated 2x4, 3-Lamp Parabolic: 48" T8 32W: Electronic: Linear Fluorescent 3: (R): Relocated 8' Strip: 48" T8 32W: Electronic: Total Proposed Watts = of

2 Interior Lighting PASSES: Design 2% better than code Interior Lighting Compliance Statement Compliance Statement: The proposed interior lighting design represented in this document is consistent with the building plans, specifications, and other calculations submitted with this permit application. The proposed interior lighting systems have been designed to meet the 2012 IECC requirements in COMcheck Version and to comply with any applicable mandatory requirements listed in the Inspection Checklist. Name - Title Signature Date 2 of

3 COMcheck Software Version Inspection Checklist Energy Code: 2012 IECC Requirements: 6.0% were addressed directly in the COMcheck software Text in the "Comments/Assumptions" column is provided by the user in the COMcheck Requirements screen. For each requirement, the user certifies that a code requirement will be met and how that is documented, or that an exception is being claimed. Where compliance is itemized in a separate table, a reference to that table is provided. Section # & Req.ID C103.2 [PR4] 1 C406 [PR9] 1 Plan Review? Comments/Assumptions Plans, specifications, and/or calculations provide all information with which compliance can be determined for the interior lighting and electrical systems and equipment and document where exceptions to the standard are claimed. Information provided should include interior lighting power calculations, wattage of bulbs and ballasts, transformers and control devices. Plans, specifications, and/or calculations provide all information with which compliance can be determined for the additional energy efficiency package options. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) 3 of

4 Section # & Req.ID 1 [EL22] 2 C [EL23] 2 C [EL15] 1 3 [EL16] 2 C [EL1] 3 2 [EL18] 1 3 [EL20] 1 3 [EL21] 1 C [EL4] 1 C405.3 [EL19] 3 C405.4 [EL6] 1 C [EL8] 1 Rough-In Electrical Inspection? Comments/Assumptions Automatic controls to shut off all building lighting installed in all buildings. Independent lighting controls installed per approved lighting plans and all manual controls readily accessible and visible to occupants. Lighting controls installed to uniformly reduce the lighting load by at least 50%. Daylight zones provided with individual controls that control the lights independent of general area lighting. Sleeping units have at least one master switch at the main entry door that controls wired luminaires and switched receptacles. Occupancy sensors installed in required spaces. Primary sidelighted areas are equipped with required lighting controls. Enclosed spaces with daylight area under skylights and rooftop monitors are equipped with required lighting controls. Separate lighting control devices for specific uses installed per approved lighting plans. Fluorescent luminaires with odd numbered lamp configurations that are within 10 feet center to center (if recess mounted) or are within 1 foot edge to edge (if pendant or surface mounted) shall be tandem wired. Exit signs do not exceed 5 watts per face. Additional interior lighting power allowed for special functions per the approved lighting plans and is automatically controlled and separated from general lighting. Additional Comments/Assumptions: Exception: Lighting controlled by occupancy sensors. Exception: Areas that are controlled by an occupancy sensor. 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) 4 of

5 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) 5 of

6 Section # & Req.ID C [FI16] 3 C303.3, C [FI1] 3 Final Inspection? Comments/Assumptions Furnished as-built drawings for electric power systems within 30 days of system acceptance. Furnished O&M instructions for systems and equipment to the building owner or designated representative. C [FI18] 1 Interior installed lamp and fixture lighting power is consistent with what is shown on the approved lighting plans, demonstrating proposed watts are less than or equal to allowed watts. See the Interior Lighting fixture schedule for values. C408.3 [FI33] 1 Lighting systems have been tested to ensure proper calibration, adjustment, programming, and operation. Additional Comments/Assumptions: 1 High Impact (Tier 1) 2 Medium Impact (Tier 2) 3 Low Impact (Tier 3) 6 of

7 of