City of Ottawa Street Lighting. HID Coach Style Luminaire

Transcription

1 TITLE: Engineering Specification RECOMMENDED: S. Edey NO: 1 REV: APPROVED: D. O Keefe LLS0001 OF REV. DATE: City of Ottawa Street Lighting HID Coach Style Luminaire For City of Ottawa Use Only

2 REVISION SHEET REVISION DESCRIPTION DATE INITIAL 1 Add Lumec LU40, csm/jb adapter brackets, and Nema Labelling. Text and Drawing 2 Title renamed General Conditions & Electrical Characteristics referenced in separate specification Light distribution: removed M-SCO-III & bulb type 3 Associated Standard Drawings identified (11.0) Revised Marking (4.6.4) Added reference to electrical characteristics (4.12) csm jb jb 4 Included Full Cutoff & Type III (4.10) jb 5 Approval and Recommended authorization changed se do For City of Ottawa Use Only LLS0001 Rev.5 Page 2 of 9

3 TABLE OF CONTENTS 1.0 GENERAL SCOPE REFERENCE STANDARDS APPROVAL OF SOURCE PHYSICAL CHARACTERISTICS MOUNTING ARRANGEMENTS TERMINAL BLOCK AND GROUND LUG CONNECTION DIAGRAM BALLAST, STARTER AND CAPACITORS LAMP SOCKET MARKING HOUSING TWIST LOCK RECEPTACLE REFRACTOR PANELS LIGHT DISTRIBUTION PATTERN COLOUR AND FINISHING ELECTRICAL CHARACTERISTICS INSPECTION PACKAGING AND SHIPPING WARRANTY INSTRUCTIONS TO BIDDERS GENERAL EXCEPTIONS MODIFICATIONS TECHNICAL INFORMATION REQUESTED SAMPLES MAINTENANCE PARTS INFORMATION SUPPLIED TO THE BIDDER DRAWINGS... 9 For City of Ottawa Use Only LLS0001 Rev.5 Page 3 of 9

4 1.0 General 1.1 Scope This specification covers the supply of High Pressure Sodium (HPS) luminaires complete with integral ballast for post-top and side mounting. This specification shall be read in conjunction with engineering specification LGC0001 and LLS Reference Standards Luminaires shall comply with all applicable requirements in the latest issues of the following standards: ANSI/IES RP-8 ANSI Standard C ANSI Standard C ANSI Standard C ANSI Standard C82.9 ANSI Standard C ANSI Standard C CSA Standard C22.2, No.9 CSA Standard C22.2, No. 43 CSA Standard C22.2, No. 74 CSA Standard C22.2, No. 97 CSA Standard C164 CSA Standard C653 Roadway Lighting Specifications for 70W S62 High Pressure Sodium Lamps Specifications for 100W S54 High Pressure Sodium Lamps Specifications for 150W S55 High Pressure Sodium Lamps Definitions for HID Lamp Ballasts and Transformers Lock-type Photocontrol Devices and Mating Receptacles Physical and Electrical Interchangeability and Testing Field Identification of High Intensity Discharge Lamps in Luminaires Luminaires Lamp holders Equipment for use with Electric Discharge Lamps Outdoor and Submersible Floodlights Hot Dip Galvanizing of Irregularly Shaped Articles Performance Standards for Roadway Lighting Luminaires NEMA Standard OD Field Identification of High-Intensity Discharge Lamps in Luminaires used in Roadway Lighting Equipment. 3.0 Approval Of Source Luminaires supplied to this specification shall be supplied only by manufacturers approved by the City of Ottawa or its agent. Only luminaires evaluated and approved by the City of Ottawa or its agent before or at the time a quotation is submitted will be accepted. Luminaires supplied shall be of the same construction as the sample luminaire currently approved by the City of Ottawa or its agent and, once approved, the supplier shall not change material, type or source or production method without prior approval from the City of Ottawa or its agent. 4.0 Physical Characteristics 4.1 Mounting Arrangements Slipfitter The luminaire shall be designed with an integral slipfitter to accommodate a 76 mm OD by 64 mm tenon and provided with three ¼ - 20 set screws to secure the luminaire to the tenon. For City of Ottawa Use Only LLS0001 Rev.5 Page 4 of 9

5 An adapter is required to mount the L40U to the standard 76mm tenon on the street lighting pole. Side Mounted The luminaire shall be designed to accept a scroll arm bracket. Refer to engineering specification XBS Terminal Block and Ground Lug A terminal block shall be provided and so placed that connection of No. 14 AWG solid copper supply wires to it will be convenient and easy to make without special tools. In addition, a ground lug shall be placed so that connection to it with a No. 14 AWG solid copper ground wire can be made easily without special tools. 4.3 Connection Diagram A connection diagram of a permanent material shall be located so as to be easily visible when making connections. 4.4 Ballast, Starter and Capacitors The ballast, starter and capacitors shall be mounted within the luminaire so that replacement may be achieved easily. Further, special precautions in the form of spacing and barriers shall be taken to shield the components from heat emitted by the lamp. Capacitors shall be non-pcb and permanently marked "Non-PCB". 4.5 Lamp Socket The standard lamp socket shall be a mogul screw base made from cold moulded porcelain and pulse rated for HPS operation. The shell shall be nickel-plated with dimples or slots to prevent the lamp loosening with vibration and shall be secured to the socket using a machine screw and nut combination. The centre contact shall be nickel-plated and spring-loaded for positive contact. 4.6 Marking Each luminaire shall have a permanent type nameplate indicating the manufacturers name, catalogue/model number, wattage, supply voltage and frequency, input current and year of manufacture. This nameplate may be a metallic nameplate attached to the luminaire with self-tapping screws or alternatively a high quality stick-on foil type label providing that the foil label is installed at the place of manufacture under quality controlled conditions and will not fade, chip, peal or otherwise deteriorate under normal service conditions A permanent label including a wiring diagram and stating ballast type and compatible starter number and capacitor value shall be provided and attached to the ballast or interior of the luminaire so that it is clearly visible during maintenance operations Labels identifying "House Side" and/or "Street Side" shall be affixed inside the luminaire so they are clearly visible during installation and maintenance Each luminaire shall have an exterior identification marker affixed to the underside of the luminaire near the bracket that would be visible from the ground and indicate the size of For City of Ottawa Use Only LLS0001 Rev.5 Page 5 of 9

6 4.7 Housing lamp used in the luminaire. When an underside location is not appropriate, a selfadhesive label is to be supplied with the fixture and attached in the location directed by the City of Ottawa Street Light agent. The luminaire housing/refractor assembly shall be designed and fabricated to prevent the ingress of moisture, insects and other foreign material. Suitable gaskets and filters shall be provided to minimize the accumulation of dirt on the lamp reflector and refractor panels. Removable covers shall be firmly secured from under side of cover but easily removed to allow access to the lamp socket, ballast, terminal block and ground connector for field servicing. 4.8 Twist Lock Receptacle The luminaire shall be equipped with a twist lock receptacle for a photoelectric controller. When installed, the photoelectric controller shall be adjustable for a north-facing window and be concealed within an imitation smoke chimney on top of the luminaire. 4.9 Refractor Panels The refractor panels shall be heat-resistant acrylic, either clear or translucent white so as not to distort the colour of the light Light Distribution Pattern Luminaires shall be adjusted at the factory for a MSCO-II, MSCO-III, MFCO-II or MFCO-III light distribution pattern. Lamp wattages are to be 70W, 100W, or 150W Colour and Finishing Except for the refractor panels, all visible parts of the luminaire shall be finished with Black Epoxy Baking Enamel. Permanent black anodizing to match is acceptable for aluminium parts. Surfaces and edges shall be smooth and free from burrs and sharp corners 4.12 Electrical Characteristics Refer to LLS Inspection The City of Ottawa or its agent reserves the right to request and be granted permission to visit the manufacturer's plant to inspect the luminaires and manufacturing methods during assembly and testing. For City of Ottawa Use Only LLS0001 Rev.5 Page 6 of 9

7 6.0 Packaging And Shipping Luminaires shall be shipped complete, suitably packaged to ensure all parts are delivered as an entity. The supplier shall advise the City of Ottawa or its agent Purchasing Department three days prior to his shipping date of his intent to deliver. 7.0 Warranty The manufacturer shall warrant that the luminaires furnished by him conform to all the requirements and conditions of this specification. The manufacture shall remedy, at no expense to the City of Ottawa or its agent, defects due to faulty workmanship, material or design for the period of one year after installation of the luminaires, but in no case for more than two years after receipt of the units by the City of Ottawa or its agent. 8.0 Instructions To Bidders 8.1 General Suppliers shall submit with their tenders the technical information requested herein. Suppliers who fail to provide the information requested might have their tenders rejected as incomplete. 8.2 Exceptions Where the tender is not in complete accordance with the requirements of this specification, the supplier shall submit a detailed list specifically outlining the exceptions or changes. If such a list is not provided, it will be understood that the supplier shall comply with all the requirements. 8.3 Modifications The supplier shall also submit a list of any changes in the design, components, construction or materials employed if the luminaires of the type being quoted differ from these previously approved by the City of Ottawa or its agent. Failure to notify the City of Ottawa or its agent of such changes when tendering may constitute sufficient reason to reject the tender. 8.4 Technical Information Requested Manufacturer's Reference a) Catalogue number of the luminaire b) Catalogue number and manufacturer of major components including ballast, starter, capacitor and refractor panels Photometric Performance a) Isocandela diagram b) Iso-lux (iso-foot candle) diagram and utilization data. For City of Ottawa Use Only LLS0001 Rev.5 Page 7 of 9

8 c) Vertical candlepower distribution curve d) Luminaire maintenance factor (suggested by manufacturer) Mechanical Characteristics a) Dead weight b) Effective projected area of luminaire c) Gasket/filter mechanisms for preventing dirt build-up on the lamp, reflector and refractor panels d) Types of finishes applied to various parts Electrical Characteristics and Performance (Rated Supply Voltage Assumed) a) Under open circuit condition, ballast input current and lamp voltage (O.C.V.) b) Inrush current on striking of arc c) Normal or operating ballast input and lamp currents and maximum values of same d) Normal or operating ballast lamp voltage e) Variation in lamp wattage for rated supply voltage variation f) Ballast power factor g) Nominal ballast supply voltage h) Input watts and losses i) Rated Life of ballast j) Ballast trapezoidal drawings Luminaire drawings and ballast schematic drawing Quality control program carried out by manufacturer including description of tests and sampling plan. 8.5 Samples Unless the luminaire being proposed has been previously approved by the City of Ottawa or its agent, the supplier shall provide a sample identical in every way to the units tendered. Samples will be returned to the supplier after evaluation. 9.0 Maintenance Parts Suppliers are requested to quote on the following maintenance parts or components: a) Ballast Kit, including ballast, capacitor, starter, and PEC receptacle prewired with interconnecting wiring and mounting hardware as required by this specification b) Refractor panels c) Starter For City of Ottawa Use Only LLS0001 Rev.5 Page 8 of 9

9 10.0 Information Supplied To The Bidder The following minimum information will be supplied to the bidders when requesting a quotation: a) Quantity b) Lamp wattage c) Light distribution pattern, if other than as specified in Section 4.10 d) Input voltage of ballast, if other than as specified in specification LLS Drawings LLD0001, LLD0006, LLD0008. For City of Ottawa Use Only LLS0001 Rev.5 Page 9 of 9