Seem 4 LED Perimeter FSM4L_FL2

Transcription

1 Seem LED Perimeter FSML_FL MUST BE INSTALLED PRIOR TO DRYWALL /HARD CEILING READ ALL INSTALLATION INSTRUCTIONS BEFORE BEGINNING INSTALLATION focal point parts key attention power off power on parts list outside corner housing inside corner 7 8 sliding sleeve (ss) (SHIPPED INSTALLED. SSB INDICATES A SLIDING SLEEVE AT BOTH ENDS) j-rail finish plate tie-wire/grid bracket corner j-rail hardware bag by others 9 0 tie-wire bracket 7 joiner bracket 8 joiner bracket 9 lens end piece 0 lens tool GRID CEILING - /" or 9/" flat tee main runner required for finish edge. housing types (' shown) WALL/CEILING PREP individual (may include sliding sleeves) j-rail must be flush with wall texture 7.7 overall height start (shown with sliding sleeve) wall texture must extend to bottom of j-rail.0 intermediate ceiling line end (shown with sliding sleeve) drywall/hard ceilings mount below housing. grid ceiling - /" or 9/" flat tee main runner required for finish edge. IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of

2 BASIC INSTALLATION STEPS - SLIDING SLEEVES SEE PG CORNERS SEE PG FOCAL POINT RECOMMENDS STARTING WITH CORNER INSTALLATION IF APPLICABLE SLIDING SLEEVE PAIRS (SSB) START & END WITH A SLIDING SLEEVE AVOID ALL CONTACT WITH LED SURFACE, LEDs ARE EASILY DAMAGED! MOUNT J-RAIL TO WALL hardware by others GRID DRYWALL/HARD CEILING use caution: damage may result if housing impacts wall bend tee tabs GRID 7 level houisng and secure to structure above with tie-wire lift housing into place engaging j-rail and tee grid 8 x 9 x 0 repeat steps - for each housing section IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of

3 REFERENCE INSTRUCTIONS ON INCLUDED TOOL FOR LENS INSTALLATION. DRYWALL/HARD CEILING drywall/hard ceiling mounts below housing (structure by others) EMERGENCY SEE BATTERY MANUFACTURER INSTRUCTIONS emergency maximum mounting height:.00 SLIDING SLEEVES MAX LENGTH " PER SLEEVE SLIDING SLEEVES & CORNERS DO NOT INTEGRATE SINGLE SLIDING SLEEVE (SS): EXAMPLE: ' run length - 0' housing = " sliding sleeve SLIDING SLEEVE PAIR (SSB): EXAMPLE: (' run length - 0' housing) / = " sliding sleeve on each end " " " IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of

4 remove knockouts for electrical access if necessary CUT FINISH PLATE TO DETERMINED LENGTH 7 8 CORNERS " MIN / " MAX PER SIDE INSIDE CORNER: "min/"max OUTSIDE CORNER: CORNERS & SLIDING SLEEVES DO NOT INTEGRATE INSIDE CORNER "min/"max."min."max OUTSIDE CORNER IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of

5 INSIDE CORNER SHOWN hardware by others lift housing into place engaging j-rail remove knockouts for electrical access if necessary SECURE TO STRUCTURE ABOVE WITH TIE-WIRE 8 TION CUT FINISH PLATE TO DETERMINED LENGTH each run requires electrical connection IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of

6 DRIVER SERVICE AVOID ALL CONTACT WITH LED SURFACE, LEDs ARE EASILY DAMAGED! Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS09 REV. D 07 Focal Point, LLC S. Pulaski Rd., Chicago, IL 0 of