focus wall wash FWSL 1 housing 2 splay 3 light module 4 j-rail 12 hardware bag 5 end cap 6 flanged end cap (FACTORY OPTION) 7 sliding sleeve & splay

Transcription

1 focus wall wash FWSL MUST BE INSTALLED PRIOR TO DRYWALL /HARD CEILING READ ALL INSTALLATION INSTRUCTIONS BEFORE BEGINNING INSTALLATION focal point parts key power off 6 7 power on 8 attention 9 parts list housing splay light module j-rail hardware bag sliding sleeve lock & splay, endcaps, j-box screw (700) (8-8 SCREW) 0 6 end cap 6 flanged end cap (FACTORY OPTION) 7 sliding sleeve & splay 8 inside corner (FACTORY OPTION) 9 (FACTORY OPTION) 0 j-box joiner bracket joiner screw (7066) (0- SCREW) joiner to splay screw (70) (6- / SCREW) housing joiner screw (70068) (SCR,0-X PHL PAN MS FST SCREW) housing joiner nut (7068) (NUT KEPS 0-) feed locations indicates feed location ' ' '.7".7".7" ' 6'.7".7" IS06 REV. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

2 WALL/CEILING PREP 9.0 +/-. BASIC INSTALLATION STEPS - SLIDING SLEEVES SEE PG LED MODULES SEE PG CORNERS SEE PG EMERGENCY CIRCUIT SEE PG FOCAL POINT RECOMMENDS STARTING WITH INSIDE CORNER INSTALLATION IF APPLICABLE ceiling line 6.0 drywall/hard ceilings mount below housing. MOUNT J-RAIL TO WALL (hardware by others) remove knockout INSTALL END CAPS ON START OF RUN AND SLIDING SLEEVE (END OF RUN) LIFT HOUSING INTO PLACE ENGAGING J-RAIL 6 LEVEL HOUISNG AND WITH TIE-WIRE 7 IS06 Rev. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

3 8 9 0 SLIDE JOINER INTO PLACE ALIGN WITH EXTRUDED EDGE. SLIDING SLEEVES SLIDING SLEEVE +/- IS06 REV. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

4 6 7 8 CUT SPLAY TO DETERMINED LENGTH 9 0 DRYWALL/HARD CEILING GRID CEILING SLIDE JOINER INTO PLACE ALIGN WITH EXTRUDED EDGE. drywall/hard ceiling mounts below housing (structure by others) IS06 REV. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

5 LED MODULE MODULE LATCH ENGAGES WITH EXTRUSION CONNECT THRU-WIRE FOR RUNS POSITION LED MODULES MAX FROM ONE ANOTHER AND MAX FROM WALL CORNERS INSIDE CORNER: OUTSIDE CORNER: inside corner start with inside corner installation POSITION LED MODULES MAX FROM WALL/CORNER LIFT CORNER INTO PLACE ENGAGING J-RAIL IS06 REV. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

6 inside corner inside corner ONE SIDE OF RUN MUST BE INSTALLED PRIOR TO OUTSIDE CORNER EMERGENCY CIRCUIT remove knockout IS06 REV. B 0 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7

7 EMERGENCY SEE BATTERY MANUFACTURER INSTRUCTIONS emergency maximum mounting height:.00 DRIVER SERVICE RELEASE LED MODULE LATCH ON BOTH SIDES a b Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. Any reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS06 REV. B 06 Focal Point, LLC S. Pulaski Rd., Chicago, IL of 7