seem 4 mud-in drywall FSM4-XF

Transcription

1 seem 4 mud-in drywall FSM4-F LUMINIRE MUST E INSTLLED PRIOR TO DRYWLL. configurations are run specific, please consult factory drawings before beginning installation. focal point parts lists key shipped in hardware bag power off U - individual reflector (70008) (6-32 5/16 PN-HED MCHINE SCREW) mud flange (70005) (8-32 5/16 FLT UNDERCUT HED SCREW) power on attention S - start of run lens tool ( ) (FFIED TO LENS. ONE PER RUN) backer flange (72001) (8-32 3/8 WSHER HE HED SCREW) housing spacer shipped installed I - intermediate tie-wire bracket screw (72010) (8-18 x 1/4 SELF TPPING SCREW) joiner bracket (920) backer flange (may be pre-installed or shipped loose) tie wire bracket (12547) E - end of run lens end piece (07670) joiner bracket (849) mud flange (shipped loose) CKER FLNGE PLCEMENT GUIDE C D E F G H Y Y orientation 1 orientation 2 drywall orientation guide point position thickness 3 /8" 1 F 1 /2" 1 E 5 /8" 1 D 3 /4" 1 C 7 /8" 1 1" /8" 1 Y G 1 1 /4" 2 Y F 1 3 /8" 2 Y E 1 1 /2" 2 Y D 1 5 /8" 2 Y C 1 3 /4" 2 Y 1 7 /8" 2 Y 2" 2 E 2 1 /8" 2 D 1 /2" drywall C D E F G H orientation 1 1 /2 5 /8" drywall C D E F G H orientation 1 5 /8 IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6

2 CEILING INSTLLTION (see page 4 for wall installation) using the backer flange placement guide from page 1 determine the proper placement of the backer flange for your drywall thickness. if backer flanges were pre-installed skip to step 5 4 2' 3' - 4' 5' - 6' 7' - 8' individual installations skip to step 8 9 x4 10 x4 IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6

3 12 make electrical connections slide reflectors together by hand. center reflectors in run. gaps at ends should be equal. secure reflectors to housing (2 screws per reflector) TTENTION before beginning drywall DRYWLL installation consult guide on install page 1 to ensure the backer flange is set at the correct depth for the drywall. spacers every 12" DRYWLL MUD IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6

4 REFERENCE INSTRUCTIONS ON INCLUDED TOOL FOR LENS INSTLLTION. WLL INSTLLTION 1 2"x6" FRMING REQUIRED ON OTH SIDES OF OF HOUSING 5.625" min 6.0" max 3 using the backer flange placement guide from page 1 determine the proper placement of the backer flange for your drywall thickness. if backer flanges were pre-installed skip to step 4 3 2' 3' - 4' 5' - 6' 7' - 8' install spacers every 12" IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6

5 7 x4 individual installations skip to step 12 9 x x4 12 OR remove spacers 90 fitting required make electrical connections install reflectors starting from bottom slide reflectors together by hand. center reflectors in run. gaps at ends should be equal. make electrical connections secure reflectors to housing (2 screws per reflector) TTENTION before beginning drywall installation consult guide on page 1 to ensure the backer flange is set at the correct depth for the drywall. DRYWLL IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6

6 DRYWLL MUD REFERENCE INSTRUCTIONS ON INCLUDED TOOL FOR LENS INSTLLTION. LLST SERVICE Contractor is responsible for adequately reinforcing walls and/or ceilings to support luminaire weight. Focal Point, LLC accepts no responsibility for inadequately reinforced walls and/or ceilings. The information contained in this drawing is the sole property of Focal Point, LLC. ny reproduction in part or whole without the written permission of Focal Point, LLC is prohibited. IS0291 Rev. H 2016 Focal Point, LLC 4141 S. Pulaski Rd., Chicago, IL of 6