Certificate of Compliance
|
|
- Thomas Lewis
- 5 years ago
- Views:
Transcription
1 Certificate of Compliance Certificate: (065182_0_000) Issued to: EGS Electrical Group LLC 9377 W Higgins Rd Rosemont, Illinois USA Attention: Steve Blais The products listed below are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US or with adjacent indicator 'US' for US only or without either indicator for Canada only. Issued by: Thong Tong Thong Tong PRODUCTS CLASS - C FIXTURES AND FITTINGS-For Hazardous Locations CLASS - C FIXTURES AND FITTINGS-For Hazardous Locations-Certified to U.S. Standards Class I Div 2; Groups A, B, C, D, T5, Type 4X, IP66, Marine Outside type Saltwater N2LED series Emergency LED wall mounted fixture Model Number N2LED2T1 Electrical Rated: 120V-277 Vac 50/60Hz N2LED series battery wall mounted fixture Model Number N2LED0T1 Input Rated: 120V-277 Vac 50/60Hz Output: 3.2Vdc, 1A, 12 W maximum N2LED series Remote wall mounted fixtures Model Numbers N2LEDR1R1 & N2LEDR2R1 Electrical Rated: 3.2Vdc, 1A, 3.2W max DQD 507 Rev Page 1
2 APPLICABLE REQUIREMENTS CAN/CSA-C22.2 No General Requirements-Canadian Electrical Code, Part II CSA Standard C22.2 No Emergency Lighting Equipment CSA Standard C22.2 No Luminaires CSA Standard C22.2 No Light emitting diode (LED equipment CAN/CSA Standard C Performance of Internally Lighted Exit Signs CSA Standard C22.2 No. 137-M Electric Luminaires for Use in Hazardous Locations UL Standard No. 844, 12 th Ed - Luminaires for Use in Hazardous (Classified) Locations UL Standard No. 924, 9 th Ed - Emergency Lighting and Power Equipment (Ninth Edition) UL Standard No. 1598, 3 rd Ed - Luminaires UL Standard No. 1598A, 1st Ed - Luminaires (Marine) MARKINGS The manufacturer is required to apply the following markings: Products shall be marked with the markings specified by the particular product standard. Products certified for Canada shall have all Caution and Warning markings in both English and French. Additional bilingual markings not covered by the product standard(s) may be required by the Authorities Having Jurisdiction. It is the responsibility of the manufacturer to provide and apply these additional markings, where applicable, in accordance with the requirements of those authorities. The products listed are eligible to bear the CSA Mark shown with adjacent indicators 'C' and 'US' for Canada and US (indicating that products have been manufactured to the requirements of both Canadian and U.S. Standards) or with adjacent indicator 'US' for US only or without either indicator for Canada only. Nameplate adhesive label material approval information: The following markings must appear on each unit, in a permanent manner. 1. The manufacturer's name or CSA File Number or Master Contract Number and CUS Monogram. 2. The catalogue number. 3. The electrical rating: rated input in Volts, Hertz, Amperes 4. The date code (indicating the month and year of manufacture). 5. The battery identification, where applicable, shall be permanently marked within the battery compartment or other location, where readily visible after installation. The battery identification includes the battery manufacturer's name, type or catalogue designation, date of manufacture and the design life expectancy. DQD 507 Rev Page 2
3 CAUTION: REPLACE BATTERY ONLY WITH (MODEL), and ATTENTION: REMPLACER LA BATTERIE UNIQUEMENT PAR UNE BATTERIE (MODÈLE) 6. Installation wiring terminal or lead identification permanently affixed to or near all terminals or leads intended for the connection of field wiring. Colour coding of leads is considered sufficient identification. CSA C22.2 No. 141, Emergency Lighting Equipment and Appareil d éclairage de secours In addition to the above markings on the unit, the following shall be provided. 7. Installation, operation, or maintenance instructions permanently affixed to each unit, or provided on a separate sheet packed with each unit, if the unit is marked "CAUTION: See instruction manual for installation, operating and maintenance instructions." and ATTENTION : Voir manuel d'instructions pour l'installation, manuel d'utilisation et d'entretien. Note: A marking that begins with the word "CAUTION" shall be permanent and shall be in the form of paint-stencilled, die-stamped, or indelible lettering, or an indelibly printed label. The word "CAUTION" shall be in letters no less than 1/8 inch (3.2mm) in height. 8. Hazardous location designation: Class I, Div 2, Groups A, B, C, D, T5 temperature code (as applicable) - In addition to the marking above, markings clarifying the suitable area classification (as per the CEC, Part I and NEC Article 505.9) may also be included, such as; - IP66 (optional) - Tye 4X (optional) - MARINE OUTSIDE TYPE SALTWATER (optional) - Class I, Zone 2, Group IIC (optional) - The following bilingual Cautions or equivalent must appear: WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT WHILE CIRCUIT IS LIVE UNLESS AREA IS KNOWN TO BE NON- HAZARDOUS, and, AVERTISSEMENT - RISQUE D'EXPLOSION. NE PAS DEBRANCHER TANT QUE LE CIRCUIT EST SOUS TENSION, A MOINS QU'IL NE S'AGISSE D'UN EMPLACEMENT NON DANGEREUX. - The following bilingual Cautions must appear near the battery: WARNING - EXPLOSION HAZARD - BATTERIES MUST ONLY BE CHANGED IN AN AREA KNOWN TO BE NON-HAZARDOUS and AVERTISSEMENT - RISQUE D'EXPLOSION AFIN D'EVITER TOUT RISQUE D'EXPLOSION, S- ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX AVANT DE CHANGER LA BATTERIE. In addition to the marking above, markings clarifying the suitable area classification (as per the CEC, Part I) may also be included, such as; Equipment Certified to the requirements of CAN/CSA C22.2 Series Standards Class I; Division 2; Groups A, B, C and/or D; T_ DQD 507 Rev Page 3
4 as applicable. In addition to the marking above, markings clarifying the suitable area classification (as per the CEC, Part I) may also be included, such as; Class I, Zone, II_; T_ DQD 507 Rev Page 4
5 Supplement to Certificate of Compliance Certificate: (065182_0_000) The products listed, including the latest revision described below, are eligible to be marked in accordance with the referenced Certificate. Project Date Description Product Certification History The scope of this project is to update report to include: - Drawing revision levels - Component manufacturer changes Update report to add alternate factory test Update report to include minor changes to construction and update to drawings HAZ : Model certification of the Marine Outside Type Emergency light, evaluated to ordinary locations prior to Hazloc evaluation DQD 507 Rev Page 1
Certificate of Compliance
Certificate of Compliance Certificate: 70072210 (065182_0_000) Issued to: EGS Electrical Group LLC 9377 W Higgins Rd Rosemont, Illinois 60018 USA Attention: Mickey Scherer The products listed below are
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2701662 Master Contract: 201067 Issued to: Chalmit Lighting A Division of Hubbell Lighting Ltd. 388 Hillington Rd Glasgow, G52 4BL United Kingdom Attention: Mr. George
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2531848 (030391_0_000) Issued to: EGS Electrical Group LLC 9377 W Higgins Rd Rosemont, Illinois 60018 USA Attention: Mickey Scherer The products listed below are
More informationCertificate of Compliance
FF0002 Certificate of Compliance Issued to: Festo AG & Co. KG Ruiterstrasse 82 Esslingen, 73734 GERMANY Attention: Mr. A. Ganzenberg The products listed below are eligible to bear the CSA Mark shown with
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1731876 (078713_0_000) Issued to: Hawke International A Division of Hubbell Limited Oxford St W Ashton-Under-Lyne, Lancashire OL7 0NA UNITED KINGDOM Attention: Andy
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1602514 (LR 39156) Master Contract: 212516 Issued to: Rosemount Analytical Inc. Process Analytic Division Solon Research & Development Ctr 6565-P Davis Industrial
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70128861 Master Contract: 229177 (LR 103294) Project: 70128861 Date Issued: 2017-04-04 Issued to: Murata Power Solutions 4118 14th Ave Markham, Ontario L3R 0J3 CANADA
More informationCertificate of Compliance
FF0001 Certificate of Compliance Certificate: 1717515 Issued to: Limatherm SA ul. Tarnowska 1 Limanowa, 34-600 POLAND Attention: Honorata Janik The products listed below are eligible to bear the CSA Mark
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2700364 (078713_0_000) Issued to: Hawke International A Division of Hubbell Limited Oxford St W Ashton-Under-Lyne, Lancashire OL7 0NA UNITED KINGDOM Attention: Roger
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2700364 (078713_0_000) Issued to: Hawke International A Division of Hubbell Limited Oxford St W Ashton-Under-Lyne, Lancashire OL7 0NA UNITED KINGDOM Attention: Andy
More informationCertificate of Compliance
Certificate of Compliance Certificate: 1015065 (078713_0_000) Issued to: Hawke International A Division of Hubbell Limited Oxford St W Ashton-Under-Lyne, Lancashire OL7 0NA UNITED KINGDOM Attention: Andy
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2557737 (LR104031) Master Contract: 182407 Issued to: Hummel AG Lise-Meitner-Strasse 2 Denzlingen, 79211 Germany Attention: Klaus Gehri The products listed below
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70038032 (166720) Issued to: WIKA Alexander Wiegand SE & Co. KG Alexander-Wiegand-Str 30 Klingenberg, 63911 GERMANY Attention: Harald Gollas The products listed below
More informationAn Urgent Bulletin from CSA International
Ref No: I10-125 Wiring Harnesses No. 2 (Supersedes INFORMS Wiring Harnesses No. 1) Date: October 29, 2010 An Urgent Bulletin from CSA International Existing Certification not affected Apply any time to
More informationInstallation Procedure Supplement Manual (Revision A, 6/2016) LECM Large Engine Control Module
Installation Procedure Supplement Manual 26832 (Revision A, 6/2016) LECM Large Engine Control Module See Manual 26757 for complete installation, operation, maintenance, and certification information. Publications
More informationAn Urgent Bulletin from CSA International
Ref No: I12-008 Component Acceptance Service No. 52 Date: February 9, 2012 An Urgent Bulletin from CSA International New Service available as of today Apply any time to have your products evaluated Announcing:
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2015-12-22 Page 1 of 13 Report Reference # E182560-V4-S35 UL TEST REPORT AND PROCEDURE Standard: ANSI/AAMI ES60601-1 (2005/(R) 2012 +A1:2012, C1: 2009/(R) 2012 + A2:2010/(R) 2012) Amendment
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2015-09-29 Page 1 of 14 Report Reference # E182560-V4-S20 UL TEST REPORT AND PROCEDURE Standard: ANSI/AAMI ES60601-1 (2005/(R) 2012 +A1:2012, C1: 2009/(R) 2012 + A2:2010/(R) 2012) Amendment
More informationINSTALLATION INSTRUCTIONS DirectAC Universal Voltage ( V) Engine Refrofit Kit TJTUNV034ACxxxB
INSTALLATION INSTRUCTIONS DirectAC Universal Voltage (120-277V) Engine Refrofit Kit TJTUNV034ACxxxB Reference spec sheet for full part numbers Installation Instructions subject to change without notice.
More informationAMIGA. Installation Instructions
AMIGA These installation instructions are for use with Drexan Energy Systems PipeGuard Hot (PGH), PipeGuard Warm (PGW) and MultiTrace (MT) self regulating heater products. This kit may be installed in
More informationELECTRICAL SAFETY Information Bulletin
ELECTRICAL SAFETY Information Bulletin January 2014 CEC-2 [rev-8] Page 1 of 8 SUBJECT: Section 2 General Rules CANADIAN ELECTRICAL CODE Administrative Rules The Safety Codes Act and associated regulations
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2164381 Master Contract: 201161 Issued to: SonoSite, Inc. 21919 30th Dr SE Bothell, WA 98021-3904 USA Attention: Jean Bishop The products listed below are eligible
More informationELECTRICAL SAFETY Information Bulletin
ELECTRICAL SAFETY Information Bulletin February 2019 Page 1 of 7 2018 CANADIAN ELECTRICAL CODE SUBJECT: Section 2 General rules Administrative The Safety Codes Act and associated regulations, supplemented
More informationCertificate of Compliance
Certificate of Compliance Certificate: 2389070 (LR 034186) Master Contract: 155560 Issued to: Rosemount Analytical Inc. Uniloc Division 2400 Barranca Pky Irvine, CA 92606 USA Attention: Dana Crowley The
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2015-09-28 Page 1 of 10 Report Reference # E182560-V4-19 UL TEST REPORT AND PROCEDURE Standard: ANSI/AAMI ES60601-1 (2005/(R) 2012 +A1:2012, C1: 2009/(R) 2012 + A2:2010/(R) 2012) Amendment
More informationStarPack LED Luminaire
INSTALLATION AND MAINTENANCE MANUAL StarPack LED Luminaire (Wet Location) Document No: 0078 Rev A Apr. 2015 IMPORTANT: Read carefully before installation and retain for future reference. NOTE: Installation
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2010-03-30 Page 1 of 12 Report Reference # E186249-A59-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: UL 60950-1, 2nd Edition, 2011-12-19 (Information Technology Equipment
More informationRef No: I Date: November 5, 2004
Ref No: I04-108 Date: November 5, 2004 INFORMATION TECHNOLOGY AND ELECTRICAL BUSINESS EQUIPMENT NO. 14 Existing Certification not affected New products to certify? Call us today! 1-800-463-6727 Announcing:
More informationTallSlateTM Grandee Installation Manual
TallSlateTM Grandee Installation Manual PLEASE READ THIS GUIDE COMPLETELY BEFORE INSTALLING OR USING THE SOLAR ELECTRIC MODULES Disclaimer of Liability...2 General Information...2 General Safety...2 TM
More informationMATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR UNDERPASS LIGHTING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 2434 November 2016 MATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR UNDERPASS LIGHTING TABLE OF CONTENTS 2434.01 SCOPE 2434.02 REFERENCES
More informationREVISION HISTORY Rev Description Author. Approved by Date A Initial release per ECO Daniel Livingston
MD200001 AGENCY DOCUMENTS, ET2401LM Series REVISION HISTORY Rev Description Author. Approved by Date A Initial release per ECO-13-0706 Daniel Livingston Daniel Livingston September 12, 2013 DOC #: MD200001
More informationPHOTOVOLTAIC (PV) SUBMITTAL REQUIREMENTS
PHOTOVOLTAIC (PV) SUBMITTAL REQUIREMENTS Building Division 555 Santa Clara Street Vallejo CA 94590 707.648.4374 1. PERMIT INFORMATION: The installation of a photovoltaic solar electric system requires
More informationProduct: Plumbing Fixtures (Stainless Steel) File No. 5914
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the
More informationROUND LIGHTPLANE 1 3D SURFACE
INSTALLATION INSTRUCTIONS ROUND LIGHTPLANE 1 3D SURFACE RLP1/3D Surface Mount Configuration LED A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com Safety & Warnings!
More informationSmall Wind Turbine Electrical System Considerations
Small Wind Turbine Electrical System Considerations Presented by: Tom Buchal Senior Staff Engineer Intertek Renewables International Small Wind Association of Testers Conference Ithaca, NY April 25, 2012
More informationDescriptive Report and Test Results
Descriptive Report and Test Results MASTER CONTRACT: 266909 REPORT: 700584 Edition 1: August 12, 2016; Project 700584 Albuquerque Prepared by Chase Henson; Reviewed by Ze Guo Contents: Certificate of Compliance
More informationSTANDARDS UPDATE NOTICE (SUN) ISSUED: August 16, 2018
STANDARDS UPDATE NOTICE (SUN) ISSUED: August 16, 2018 STANDARD INFORMATION Standard Number: CSA C22.2 No. 223 Standard Name: Power Supplies with Extra-Low-Voltage Class 2 Outputs Standard Edition and Issue
More informationOptoLum MegaLine RGBW Luminaire
OptoLum MegaLine RGBW Luminaire Getting Started OptoLum MegaLine RGBW Luminaires offer indoor cove lighting and wall washing in a compact linear form. This guide contains important information on planning,
More informationBLAZE BASICS 100 LED Tape Light 24V. 18/ft Color Temperature. 2700K, 3000K, 5000K CRI 90+ Dimmable
diode led a division of elemental LED BLAZE BASICS 100 LED Tape Light UL Listed Field Cuttable 12VDC 24VDC IP20 90 HIGH CRI Item # Project 12V 24V DI12VBLBSC1 DI24VBLBSC1 Voltage 12V 24V Wattage 1.46/ft.
More informationMATERIAL SPECIFICATION FOR SIGNAL HEADS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 2461 April 2017 MATERIAL SPECIFICATION FOR SIGNAL HEADS TABLE OF CONTENTS 2461.01 SCOPE 2461.02 REFERENCES 2461.03 DEFINITIONS 2461.04 DESIGN
More informationCity of Ottawa Street Lighting. Photoelectric Controllers
TITLE: Engineering Specification RECOMMENDED: S. Edey NO: 1 REV: APPROVED: D. O Keefe LAS0001 OF REV. DATE: 2010-01-07 7 2 City of Ottawa Street Lighting Photoelectric Controllers For City of Ottawa Use
More informationINFORMATION BULLETIN
APPROVAL OF MANUFACTURED HOMES & FACTORY-BUILT STRUCTURES (RELOCATABLE AND NON-RELOCATABLE) The following bulletin provides guidance on the application Electrical Safety Regulation, Section 21. This information
More informationSECTION FIELD PANELS
Stanford University Facilities Design Guidelines SECTION 25 14 23 FIELD PANELS PART 1 - GENERAL 1.1 SUMMARY A. This section includes control panel and enclosure requirements for building control systems.
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 4. Trim. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 4 Trim A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP4R - Safety & Warnings! 1. Read all instructions. 2. Install
More informationEFFECTIVE DATE: November 1, 2011, unless a later date is cited at the end of a section. [ NMAC - Rp,
TITLE 14 CHAPTER 10 PART 4 HOUSING AND CONSTRUCTION ELECTRICAL CODES 2011 NEW MEXICO ELECTRICAL CODE 14.10.4.1 ISSUING AGENCY: The Construction Industries Division of the Regulation and Licensing Department.
More informationCertificate of Compliance
Certificate of Compliance Certificate: 70025164 Issued to: Vega Grieshaber KG Am Hohenstein 113 Schiltach, Baden-Württemberg 77761 GERMANY Attention: Sebastian Schaller The products listed below are eligible
More informationReference Information:
Solar PV Simplified Standard Permit Application Requirements For: Central/String Inverter(s) & Micro-Inverter(s) Systems for One and Two Family Dwellings SCOPE: Use this application only for utility-interactive
More informationMATERIAL SPECIFICATION FOR LUMINAIRE RAISING AND LOWERING EQUIPMENT
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 2476 JANUARY 1990 MATERIAL SPECIFICATION FOR LUMINAIRE RAISING AND LOWERING EQUIPMENT 2476.01 SCOPE 2476.02 REFERENCES 2476.05 MATERIALS TABLE OF CONTENTS
More informationSECTION SECTIONAL OVERHEAD DOORS 511 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 511 SERIES ALUMINUM SECTIONAL OVERHEAD DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word
More informationMANUFACTURER'S RESPONSIBILITIES AND REQUIREMENTS FOR FACTORY TESTS
MANUFACTURER'S RESPONSIBILITIES AND REQUIREMENTS FOR FACTORY TESTS 1.0 MANUFACTURER'S RESPONSIBILITIES: The manufacturer's responsibilities include, but are not limited to: 1.1 Control of UL Mark - Restrict
More informationAmendment A National Electric Code
Amendment A-5 2014 National Electric Code Part 5 BUILDING REGULATIONS AND CODES National Electric Code, 2014 Edition (NEC, 2014) Part 5, Chapter 5 National Electric Code Article 100 I. General ENGINEERING
More informationSECTION 16496A MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number
MTS MANUAL TRANSFER SWITCH (MANUAL CONTROL ONLY) Note to Spec Writer: { } Denotes EATON Feature reference number PART 1 GENERAL 01 02 03 04 SCOPE Furnish and install Manual Transfer Switches (MTS) and
More informationSECTION SECTIONAL OVERHEAD DOORS 416 SERIES SECTIONAL STEEL DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 416 SERIES SECTIONAL STEEL DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on
More informationSECTION SECTIONAL OVERHEAD DOORS 424 SERIES SECTIONAL STEEL DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 424 SERIES SECTIONAL STEEL DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on
More informationPD662 LOOP-POWERED METER Instruction Manual
PD662 LOOP-POWERED METER C US 4-20 ma Input Loop-Powered -1999 to 2999 Display Easy Four-Button Programming NEMA 4X Enclosure Programmable Noise Filter Loop-Powered Backlight Option 1.7 Volt Drop without
More informationUL TEST REPORT AND PROCEDURE
Issue Date: 2012-02-09 Page 1 of 22 Report Reference # E254758-A32-UL UL TEST REPORT AND PROCEDURE Standard: Certification Type: CCN: Product: Model: ANSI/AAMI ES60601-1 (2005 + C1:09 + A2:10)(Medical
More informationFile E Project June 27, 2014 REPORT. Cabinets and Cutout Boxes. BOCCHIOTTI SPA Milano, MI, Italy
Copyright 2014 UL LLC File E466141 Project 4786190420 June 27, 2014 REPORT On Cabinets and Cutout Boxes BOCCHIOTTI SPA Milano, MI, Italy UL LLC authorizes the above named company to reproduce this Report
More informationINSTALLATION INSTRUCTIONS SUPERPLANE 4. Mud-In. A nd Avenue, Unit 1 Oakland, CA P E W alwusa.
INSTALLATION INSTRUCTIONS SUPERPLANE 4 Mud-In A 1035 22nd Avenue, Unit 1 Oakland, CA 94606 P 510.489.2530 E TalkToUs@alwusa.com W alwusa.com SP4R - Safety & Warnings! 1. Read all instructions. 2. Install
More informationDangerous Goods and Rail Safety. A Technical Publication from the Co-ordination and Information Centre. Documentation Review
Dangerous Goods and Rail Safety A Technical Publication from the Co-ordination and Information Centre Documentation Review July 2017 - 2 - This material is meant as a guide to certain parts of the Transportation
More informationBULLETIN SUBJECT: GENERAL BULLETIN, 2015 SASK INTERPRETATIONS CORRECTIONS, AND ELECTRIC SERVICE REQUIREMENT CHANGES OR ADDITIONS
SaskPower Electrical Inspections BULLETIN 01-2017 February 15, 2017 TO: LICENSED ELECTRICAL CONTRACTORS ELECTRICAL CONSULTANTS AND ENGINEERS SUBJECT: GENERAL BULLETIN, 2015 SASK INTERPRETATIONS CORRECTIONS,
More informationRECOGNIZED COMPONENT Constructional Data Report (CDR)
RECOGNIZED COMPONENT Constructional Data Report (CDR) 1.0 Reference and Address Report Number 150611019SZN-001 Original Standard(s) Applicant Information Technology Equipment Safety Part 1: General Requirements
More informationTop Changes 2014 NEC
Top Changes 2014 NEC MICHAEL JOHNSTON EXECUTIVE DIRECTOR STANDARDS AND SAFETY NECA General Information This presentation previews significant changes for the 2014 NEC. Two-part series on 2014 NEC changes
More informationSECTION SECTIONAL OVERHEAD DOORS 418 SERIES INSULATED STEEL DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 418 SERIES INSULATED STEEL DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on
More informationMATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR HIGHWAY LIGHTING
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS 2432 NOVEMBER 2015 MATERIAL SPECIFICATION FOR HIGH PRESSURE SODIUM LUMINAIRES FOR HIGHWAY LIGHTING TABLE OF CONTENTS 2432.01 SCOPE 2432.02 REFERENCES
More informationMar11 Rev B
Product Specification 108-1543 11Mar11 Rev B Header, MATE-N-LOK*, Mini-Universal 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for MATE-N-LOK* mini-universal
More informationSECTION SECTIONAL OVERHEAD DOORS 422 SERIES INSULATED STEEL DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 422 SERIES INSULATED STEEL DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on
More informationSECTION SECTIONAL OVERHEAD DOORS 432 SERIES INSULATED STEEL DOORS
SECTION 08 36 00 SECTIONAL OVERHEAD DOORS 432 SERIES INSULATED STEEL DOORS Display hidden notes to specifier by using Tools / Options / View / Hidden Text. On newer versions of Microsoft Word click on
More informationRevised October 2017, the information contained in this bulletin supercedes the requirements of all previous bulletins.
EB 0901 Revised October 2017, the information contained in this bulletin supercedes the requirements of all previous bulletins. 1. An Electrical Permit must be purchased BEFORE electrical work is carried
More informationLARSON ELECTRONICS, LLC US-HWY 175 Kemp, Texas USA
LARSON ELECTRONICS, LLC. 99 US-HWY Kemp, Texas USA INSTALLATION, OPERATION & MAINTENANCE DATA SHEET For EPL-AEC Series Threaded Enclosures. For use in Class I, Groups B, C & D, Class II, Groups E, F &
More informationUNIFIED FACILITIES GUIDE SPECIFICATIONS
USACE / NAVFAC / AFCEC / NASA UFGS-01 33 23.33 (February 2010) -------------------------------- Preparing Activity: USACE UNIFIED FACILITIES GUIDE SPECIFICATIONS References are in agreement with UMRL dated
More informationSECTION SECONDARY UNIT SUBSTATIONS
SECTION 26 12 16 SECONDARY UNIT SUBSTATIONS PART 1 GENERAL 1.1 SUMMARY This section describes metal-clad, indoor or outdoor, secondary unit substations with integral primary fused disconnect switches,
More informationMATERIAL SPECIFICATION FOR UNINTERRUPTIBLE POWER SUPPLY SYSTEMS FOR LED TRAFFIC SIGNALS
ONTARIO PROVINCIAL STANDARD SPECIFICATION METRIC OPSS.PROV 2475 April 2017 MATERIAL SPECIFICATION FOR UNINTERRUPTIBLE POWER SUPPLY SYSTEMS FOR LED TRAFFIC SIGNALS TABLE OF CONTENTS 2475.01 SCOPE 2475.02
More informationWilo MC Self Priming, Horizontal Multi-Stage, High Pressure Pumps. Engineering Specification
Wilo MC Self Priming, Horizontal Multi-Stage, High Pressure Pumps Engineering Specification PART 1 - GENERAL 1.1 SUMMARY A. Furnish and install horizontal multi-stage, high pressure, self priming pressure
More informationQPS Evaluation Services Inc.
QPS Evaluation Services Inc. Testing, Certification, and Field Evaluation Body Accredited in Canada, the USA and Internationally YOUR FULL SERVICE PARTNER IN GLOBAL CONFORMITY ASSESSMENT TESTING - CERTIFICATION
More informationMUSCO ENGINEERING ASSOCIATES Consulting Engineers
Consulting Engineers website: www.muscoengineering.com 375 Morgan Lane, Unit 307 West Haven, CT 06516 Telephone #: (203) 932-1901 Fax #: (203) 931-1550 email: admin@muscoengineering.com Electrical Equipment
More informationELECTRICAL INSPECTION BULLETIN (Effective )
ELECTRICAL INSPECTION BULLETIN (Effective 2009-02-01) Rule 36-000 Customer Owned High Voltage Installations With the increase in customer own high voltage equipment there appears to be confusion over which
More informationSECTION CONVECTORS
SECTION 23 82 33 PART 1 - GENERAL 1.1 DESCRIPTION SPEC WRITER NOTES: 1. Use this section only for NCA projects. 2. Delete between // // if not applicable to project. Also delete any other item or paragraph
More informationWhat to You Need to Know When Limited Production Certification is Your Hazardous Locations Compliance Strategy
What to You Need to Know When Intertek 70 Codman Hill Road Boxborough, MA 01719 www.intertek.com/hazloc 1-800-WORLDLAB icenter@intertek.com Introduction Complying with safety standards and requirements
More informationDangerous Goods and Rail Safety. A Technical Publication from ALBERTA EDGE (ENVIRONMENTAL AND DANGEROUS GOODS EMERGENCIES) Documentation Review
Dangerous Goods and Rail Safety A Technical Publication from ALBERTA EDGE (ENVIRONMENTAL AND DANGEROUS GOODS EMERGENCIES) Documentation Review February 2018 - 2 - This material is meant as a guide to certain
More informationLIGHTING RETROFIT CONFORMANCE REPORT
LIGHTING RETROFIT CONFORMANCE REPORT Date Contractor Permit Number Business Owner Site Address Program Type Fixture Type Quantity Voltage Amperage Max Wattage Bulletin Requirements YES / NO Requirements
More informationELECTRICAL EQUIPMENT (PRODUCT) APPROVAL REQUIREMENTS
PURPOSE INFORMATION BULLETIN / PUBLIC ELECTRICAL CODE REFERENCE NO.: LAEC 110.2, 110.3, 93.0401,0402 & 0403 Effective: 01-01-2017 DOCUMENT NO.: P/EC 2017-013 Revised: Previously Issued As: P/EC 2014-013
More informationA. Provide a complete Distribution Panelboard system as indicated on the drawings, and as specified herein.
16470 PANELBOARDS ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 24 16 An optional keynote to
More informationDec05 Rev A
Product Specification Z-DOK* and Z-DOK*+ Connectors 108-1985 12Dec05 Rev A 1. SCOPE 1.1. Content This specification covers performance, tests and quality requirements for Z-DOK* and Z-DOK*+ Connectors.
More informationV1504 VERTICAL PLATFORM LIFT PLANNING GUIDE
V1504 VERTICAL PLATFORM LIFT PLANNING GUIDE Applicable Codes: ASME A17.1 ASME A18.1 CAN/CSA B355 CAN/CSA B613 Part No. 000690 22-m08-2017 Copyright 2017 Savaria Concord Lifts, Inc. All rights reserved.
More informationDangerous Goods and Rail Safety. A Technical Publication from the Co-ordination and Information Centre. Documentation Review
Dangerous Goods and Rail Safety A Technical Publication from the Co-ordination and Information Centre Documentation Review February 2018 - 2 - This material is meant as a guide to certain parts of the
More informationSPECIFIC TECHNICAL CRITERIA
Issue Date: 2004-09-15 Page 4 of 55 Report Reference # E116994-A16-UL-1 SPECIFIC TECHNICAL CRITERIA TEST REPORT UL2601-1 Medical Electrical Equipment Part 1: General requirements for safety Report Reference
More informationBUSWAY LOW VOLTAGE (POW-R-WAY III) SECTION SECTION 16466
BUSWAY LOW VOLTAGE (POW-R-WAY III) PART 1 GENERAL 1.01 1.02 SCOPE The Contractor shall furnish and install the busway system including all necessary fittings, hangers and accessories as specified herein
More information37-SDMS-01 REV. 03 SPECIFICATIONS FOR
37-SDMS-01 REV. 03 SPECIFICATIONS FOR LOW VOLTAGE MOLDED CASE CIRCUIT BREAKERS FOR SERVICE CONNECTIONS This specification is property of SEC and subject to change or modification without any notice CLAUSE
More informationCONSTRUCTION STANDARDS SECTION CS 15 STREET LIGHTING
CONSTRUCTION STANDARDS SECTION CS 15 STREET LIGHTING CS 15-0l SCOPE: Street Lighting improvements shall be constructed in conformance with Section 86, Signals, Lighting and Electrical Systems, of the CALTRANS
More informationBuilding and Safety Division Public Information
B&S STD E-18 Solar Photovoltaic (PV) Systems Revised: January, 2017 The following document outlines the requirements for the issuance of building and electrical permits for solar photovoltaic systems.
More informationArticle 10 - ADMINISTRATIVE SECTION
Article 10 - ADMINISTRATIVE SECTION 10.1 TITLE These Administrative Regulations along with the requirements included in the 2005 Edition of the National Electrical Code (NFiPA-70-2005) as approved by the
More informationEffective Date: December Rev. 3/22/2018- Void After: December Product: Flush Valves File No. 3949
IAPMO Research and Testing, Inc. is a product certification body which tests and inspects samples taken from the supplier's stock or from the market or a combination of both to verify compliance to the
More informationRegardless of any alternative pricing provided, a quotation for the items specified herein shall be provided.
1/5 1.0 PURPOSE This specification describes the minimum requirements for design, material and construction requirements for air receivers. Ensure the design and fabrication of equipment and associated
More informationSECTION AUTOMATIC TRANSFER SWITCH
SECTION 26 36 23 AUTOMATIC TRANSFER SWITCH PART 1: GENERAL 1.01 SCOPE A. Furnish all labor, materials, equipment and appurtenances, install and test electrically operated, automatic transfer switch (ATS)
More informationRef No: N Date: August 26, 2009
Ref No: N09-052 Date: August 26, 2009 ELECTRICAL TOOLS NO. 23 (Supersedes Certification Notices and Informs in Attachment 1) Effective Date: Call us today! We can help you stay on top of changes that will
More informationLabeling of Wireless Devices Prepared by Element Materials Technology
Labeling of Wireless Devices Prepared by Element Materials Technology FCC FCC ID: Statement 47 CFR 2.925(a)(1): FCC Identifier consisting of the two elements in the exact order specified in 2.926. The
More informationInspection Guide for PV Systems in One- and Two- Family Dwellings (For Rooftop Photovoltaic Systems meeting the Standard Plan)
TOOLKIT DOCUMENT #7 Inspection Guide for PV Systems in One- and Two- Family Dwellings (For Rooftop Photovoltaic Systems meeting the Standard Plan) This document has two sections. Neither section is all-inclusive
More informationThe Canadian Electrical Code (Saskatchewan Amendments) Regulations, 1999
CANADIAN ELECTRICAL CODE 1 The Canadian Electrical Code (Saskatchewan Amendments) Regulations, 1999 Repealed by Chapter E-6.3 Reg 8 (effective June 24, 2003). Formerly Chapter E-6.3 Reg 6 (effective March
More informationApproval Standard. for. Electrical Equipment for Measurement, Control and Laboratory Use
Approval Standard for Electrical Equipment for Measurement, Control and Laboratory Use Class Number 3810 January 2005 2005 FM Approvals LLC. All rights reserved. Foreword Approval Standards are intended
More information