Design+ Flooring Installation instructions for the patented installation system UNI fit!

Transcription

1 Design+ Flooring Instlltion instrutions for the ptented instlltion system UNI fit! DUAL SEAL

2 Neessry testing nd preprtion / Su-floors 1. Neessry testing nd preprtions EGGER's Design+ flooring is mnuftured in speifi prodution stges in the most modern prodution sites. Both finished nd semi-finished produts re sujeted to regulr nd stringent heks. Despite qulity ontrols, dmge to individul ords, for exmple during trnsport, nnot lwys e ompletely prevented. Therefore, it is requirement to doule-hek Design+ flooring elements efore the instlltion jo. 2. Su-floors 2.1 All su-floors must e prepred for instlltion in ordne with norml su-floor preprtion proedures nd epted tolernes within the flooring industry. Plese onsider the following points efore strting to instll EGGER Design+ flooring: Cheking the moisture level in the su-floor: Use CM devie to ensure the following levels re not exeeded: For ement sreed 2 CM % heted sreed 1.8 CM % For lium sulphte sreed / lium sulphte sreed 0.5 CM % heted onrete 0.3 CM % These vlues pply to sreeds without dditives. With the use of dditives nd in se of fst-setting sreed, the mesurements nd limits speified y the respetive mnufturer shll pply. The test mteril must e otined from the lower one-third of the sreed. During this proess, the thikness of the sreed must e mesured nd doumented. Cheking if the su-floor is level: The test for level floor is sed on ommon stndrds nd tkes ple y pling yrdstik / strightedge on the high points of the surfe nd determining the guge t the deepest lotion in reltion to the ering surfes (mesuring point intervls). Use mx. 2 mm guge (vertil devition) t 100 m intervls. Lrger devitions should e ddressed y suitle mesures (e.g. with self-levelling ompounds). Cheking the lod ering pity of the su-floor: The su-floor must e seled, self-supporting lyer. Cheking if the su-floor is len: The su-floor must e vuum lened. Cheking tmospheri onditions: The following onditions should e met efore, during nd fter instlltion: n ir temperture of min. 18 C floor surfe temperture of min. 15 C reltive ir humidity of etween 40 % nd 70 % 2.2 Suitle for the full-surfe glueing of EGGER Design+ flooring: ll types of sreed inluding hot wter-heted sreed ermi tiles hipord strutures fireords whih pply when estlishing rediness for instlltion in line with the requirements outlined under point 2.1. Su-floors not suitle for full-surfe glueing re: textile floor overings existing floor overings mde of PVC, linoleum, vinyl su-floors not prepred for instlltion in ordne with norml proedures nd epted tolernes within the flooring industry 2.3 EGGER Design+ flooring instlled s floting flooring system n e instlled on ll su-floors whih meet the requirements desried under point 2.1. This inludes: ll types of sreed inluding hot wter-heted sreed hipord onstrutions fireords floor overings suh s PVC, linoleum, nd ermi tiles 2

3 Su-floors not suitle for floting instlltion re: textile floor overings Su-floors not prepred for instlltion in ordne with norml proedures nd epted tolernes within the flooring industry Su-floors with limited degree of suitility for oth floting instlltion nd full-surfe glueing re: eletrilly operted floor nd film heting systems (ontrol of surfe temperture) Eletril floor heting systems re lssified s su-floors with limited suitility given tht rnge of film-sed, eletril heting systems re le to generte surfe tempertures tht signifintly exeed 28 C. EGGER pproves n eletrilly operted floor heting system when the elow pplies: it is integrted in the sreed or the onrete lyer nd n e ontrolled digitlly, so tht the surfe temperture never exeeds 28 C. it is film heting system loted on top of the sreed / onrete lyer nd n e ontrolled digitlly, so tht the surfe temperture never exeeds 28 C. the mnufturer hs delred the produt s tehnilly suitle for instlltion in omintion with lminte flooring nd multilyer, modulr floors (EGGER Cork+, EGGER Design+) with Cli onnetion. Attention! When instlling on minerl su-floors, it is solutely neessry to instll moisture protetion film with n SD vlue > 75 m s vpour rrier elow the insultion underly, on the entire surfe nd extending up the wll. When using insulting produts whih re not prt of the EGGER essories rnge, floting instlltion on heted flooring strutures (surfe heting systems) voids ll wrrnties with regrd to ompline with the effetive, mximum llowle therml trnsfer resistne of the overll struture. Sreed When instlling EGGER Design + flooring onto sreed using the full-surfe glueing method, it is oligtory to ensure tht n dhesive or dhesive system pproved y EGGER is used for this purpose. An overview of pproved dhesives is ville t For floting instlltion of EGGER Design + flooring over sreed, it must e tken into ount tht possile residul moisture in the su-floor will seep to the surfe. This requires lying moisture protetion film with n SD vlue > 75 m s vpour rrier efore pplying system-speifi insulting su-floor ross the full surfe nd extending up the wll using the full-surfe glueing method (exeption st sphlt). The strips must overlp in the joining res y 20 m, or in the se of omintion mts (see EGGER Silenzio Duo), ording to instlltion instrutions. Suitle / pproved underlys re ville t Sreeds with hot wter floor heting When uilding heted flooring struture, ll prtiipnts (uilder, rhitet, heting speilist, heting tehniin, instller, nd flooring mnufturer) should o-ordinte tehnil requirements with eh other. Any surfe-heted flooring requires pproprite plnning nd o-ordintion for the heting system nd sreed to ensure mximum long-term performne without using ny dmge. Importnt: The surfe temperture of heted floor my not exeed 28 C (83 F). Prior to eginning the flooring instlltion, existing floor overings must e removed nd the su-floor's suitility for instlltion (levelness, lod ering pity, moisture) must e heked ording to the EGGER instlltion instrutions for Design+ floors. The stndrd heks of the instlltion su-floor must inlude inspeting the funtion of the floor heting / ooling system (funtionl heting / ooling), nd in ddition, proper rising nd lowering of the temperture of the heted sreed struture in ny seson must e proven nd doumented. Funtionl heting nd floor uring heting When heting the lod nd het distriution lyer, distintion is mde etween funtionl heting nd floor uring heting. Funtionl heting: Funtionl heting is the proof of the heting instller tht proper struture hs een uilt nd is used to verify the funtionlity of heted flooring strutures. Funtionl heting must tke ple ording to DIN EN As prt of the heting system instlltion, funtionl heting must tke ple nd e doumented ording to the mnufturer's instrutions nd the orresponding heting protool. In the event tht the su-floor is ement sreed, the heting-up phse must not egin efore 21 dys from instlltion. In the event tht the su-floor is lium sulphte sreed, do not strt the heting-up phse efore 7 dys fter instlltion. Attention! Oserve the mnufturer s speifitions! Begin the heting-up phse with wter temperture of 25 C (77 F), whih must e mintined for three dys. The wter temperture is susequently inresed until the design flow wter temperture is rehed (generlly 45 C / 131 F). Mintin the mximum flow wter temperture over period of 4 dys without night-time shutoff. Importnt: Funtionl heting does not gurntee tht the sreed hs rehed the residul moisture required for instlltion suitility. Therefore, instlltion uring eomes or is generlly neessry. 3

4 Floor uring heting: This is the expelling of the residul moisture in the sreed until instlltion suitility is rehed. In the event tht the su-floor is ement sreed, do not strt the heting-up phse until minimum 28 dys fter instlltion. In the event tht the su-floor is lium sulphte sreed, do not strt the heting-up phse until minimum 14 dys fter instlltion. Attention! Oserve the mnufturer s speifitions! Requirements for the mximum sreed moisture (CM mesurement) if the top floor is Design+ floor: Cement sreed (trget): 1.8 % Clium sulphte sreed (trget): 0.3 % When full-surfe glueing EGGER Design + flooring elements over heted sreed, it is oligtory to ensure tht n dhesive or dhesive system pproved y EGGER is used. An overview of pproved dhesives is ville t For the floting instlltion of EGGER Design + flooring over heted sreed, it must e tken into ount tht possile residul moisture in the su-floor will seep to the surfe of the su-floor. This requires lying over ll sreeds moisture protetion film with SD vlue > 75 m s vpour rrier efore pplying system-speifi insulting su-floor ross the full surfe nd extending up the wll. When properly instlled, the strips must overlp in the joining res y 20 m, or, in the se of omintion mts (see EGGER Silenzio Duo), ording to proessing instrutions. When using insulting lyers outside of the EGGER essories rnge, floting instlltion on heted sreed voids ll wrrnties in regrds to ompline with the effetive, mximum llowle therml trnsfer resistne of the overll struture. Suitle / pproved underlys re ville t Floor heting systems whih het nd ool: These systems re lso suitle if ll forementioned points, suh s relese y the system mnufturer for use under EGGER Design+ flooring, digitl temperture ontrol, s well s mximum surfe temperture of 28 C when heting, re oserved. Furthermore, when ooling, these systems must mintin minimum surfe temperture of 15 C. The proper instlltion of dew point sensor to monitor possily ourring ondenstion is lso required. Woodhip nd fireord When full-surfe glueing EGGER Design + flooring elements on woodhip or fireord, it is oligtory to mke sure tht n dhesive or dhesive system pproved y EGGER is used. An overview of pproved dhesives is ville t For floting instlltion of EGGER Design + floors on woodhip or fireords, system-speifi insulting lyer must e used to improve the impt nd mient sound. A vpour rrier is not neessry. Suitle / pproved underlys re ville t Cermi tiles When full-surfe glueing EGGER Design + flooring over ermi tiles, it is neessry to ensure tht n dhesive or dhesive system pproved y EGGER is used. An overview of pproved dhesives is ville t For floting instlltion of EGGER Design + flooring on ermi tiles, it should e tken into ount tht possile residul moisture in the su-floor will seep to the surfe. This requires lying moisture protetion film with SD vlue > 75 m s vpour rrier efore pplying system-speifi insulting su-floor, ross the full surfe nd extending up the wll. For proper instlltion, the strips must overlp in the joining res y 20 m, or in the se of omintion mts (see EGGER Silenzio Duo), ording to proessing instrutions. Suitle / pproved underlys re ville t Elsti flooring surfes (PVC, linoleum, vinyl) The full-surfe glueing of EGGER Design + flooring on elsti flooring surfes is not permitted. The floting instlltion of EGGER Design + flooring on elsti flooring surfes is permitted if the ltter re in suitle stte, disply stle nd losed surfe (no ulges / dethments, no rks), nd re onsidered suffiient for instlltion with regrd to the requirements outlined under point 2.1. For floting instlltion of EGGER Design + flooring on suh surfes, instlling moisture protetion film nd impt sound underly is not neessry, given tht the elsti flooring surfe fulfills these roles. 4

5 3. INSTALLATION PREPARATION Alimtising the flooring pnels Prior to instlltion, the Design+ flooring must e stored nd limtised in the room where they will e instlled or in room with the sme limte ondition. Alimtistion must follow the elow onditions: unopened pkging over period of t lest 48 hours lid flt, minimum of 50 m from ll wlls t room temperture of minimum 18 C t flooring surfe temperture of minimum 15 C t reltive tmospheri humidity of etween 40 % nd 70 % Lying diretion There is no speifi lying diretion required, therefore EGGER Design+ flooring n e instlled s preferred. However, Design+ flooring looks est when the ords re instlled prllel to the light diretion. Plnning the first row First, the room must e mesured to determine whether the width of the first row of ords should e redued. This will e neessry if the lst row is lulted to e less thn 5 m wide. Attention! The pnel should e ut lengthwys strting from the tongue side (red plsti lip). Plnning expnsion gps EGGER Design+ flooring hs speifi movement ehviour due to hnging mient limte onditions. Movement of the finished, instlled floor will pose no prolems when llowed through the use of expnsion joints to ll fixed ojets. Noise trnsfer is therefore lso voided. Consequently, to ensure sound insultion from the rest of the struture (the wlls), oth the floting instlltion nd the fullsurfe glueing of Design+ flooring requires n edge / wll distne of width of 8 mm to 10 mm to the fixed omponents of the onstrution, suh s wlls, door frmes, pipe onduits, pillrs, stirwys, et. Plnning movement profiles Given the mteril-speifi movement ehviour of Design+ floors nd reognised rules of the trde, movement profiles must lwys e uilt into the following surfe res / room sizes: ) in the se of instlltion vi full-surfe glueing: In the se of full-surfe instlltion of Design + flooring, movement profiles only need to e uilt into door thresholds / pssgewys if there is funtionlly required joint (expnsion joint) inluded in the struture. Both res must overlp in spe, s funtionlly required onstrution joints must e expnded into the top floor. In the se of full-surfe glueing of Design + flooring, the mximum surfe size is determined y the funtionlly required onstrution joints. In this generl ontext, the following reognised rule of the trde pplies: All funtionlly required onstrution joints (e.g., movement joints) loted in the su-floor my never e sujeted to forefitting losing nd must e expnded into the top floor. ) in se of floting instlltion: door thresholds pssgewys ngled res individul room lengths nd / or widths of more thn 15 m Attention! With most profile types, the se (su-profile) to ept the over profile must e instlled prior to instlling the EGGER Design+ floor. Built-in kithens / uilt-in inets Built-in kithens nd uilt-in inets should e ssemled prior to instlltion nd the Design+ floor should e pled only until under the plinth pnel. 5

6 4. INSTALLATION Privte living re: In privte pplition res, EGGER Design+ floors enefit from the ptented UNI fit! onnetion, oth glued over the whole re or instlled s floting floor. We reommend instlltion vi full-surfe glueing, s desried in setion 4.1, s it hs series of dvntges. signifint improvement of footfll sound (mient sound) nd impt sound optiml suitility for floor heting, i.e., more effiient het flow due to minimised therml trnsfer resistne stle nd ompt Design+ flooring with redued movement ehviour nd low instlltion height lrge surfe instlltion, given tht only funtionlly required onstrution joints must e expnded into the top floor (Design+ flooring) vi movement profile Alterntively, the EGGER Design + floor n lso e used in privte living res with floting instlltion, s desried under point 4.2. Commeril re: In ll ommeril pplition res (spe used ommerilly), the EGGER Design+ floors must e glued full-surfe s desried under point 4.1. In se of non-ompline, ll wrrnty lims re void Instlltion vi full-surfe glueing As generl rule: The su-floor prepred for floor ldding works must e dry, len, free of relese gents, rk-free, level, s well s disply tensile nd ompression strength ording to DIN nd DIN (With regrd to levelness, the inresed requirement of < 2 mm / m must e oserved.) The floor instller must express ny onerns in writing if the su-floor is not redy for instlltion, i.e. if it displys defets or the top floor my e dmged due to the su-floor's struture. If the levelness of the su-floor s required for instlltion is not hieved, preot nd / or filling must e pplied s speifi to the system. The sreed must e snded nd spirted with n industril vuum lener. The full-surfe glueing of EGGER Design+ flooring must tke ple using the dhesives listed nd pproved t All speifitions provided y the dhesive mnufturer, for exmple fitting nd setting times, must e oserved. The dhesive must e pplied on the entire surfe with the stipulted trowel noth. Depending on the su-floor, the nothed trowel must e repled y new one every m². Generlly speking: Fulty plements in the dhesive ed must e voided, nd ground ots or fillings tht my e neessry must e exeuted system-speifilly, s instlltion sfety nd n optiml instlltion result n only e gurnteed y using oordinted uilding mterils. EGGER Retil Produts GmH & Co. KG is not lile for the proper use nd proessing of the dhesive system. In the se of the full-surfe glueing of EGGER Design+ flooring, the individul ords re loked with the help of the ptented UNI fit! onnetion, pled nd pressed one y one, so tht the full surfe of the ord reverse is overed. Chek the elements for visile dmge / defets efore instlltion. Also ensure tht the reverse of the Design + floor elements re free of dust nd identify whih is the tongue nd the groove of the elements (fig. K5 / K6). The dhesive is pplied onto the su-floor with the help of nothed trowel to the flooring elements. As rule, egin pplying the dhesive in left-hnd room orner nd ontinue ross the entire length of the rows to e instlled, for mximum width of 50 m, so tht there re lwys 2 rows of EGGER Design+ flooring tht n e instlled t one (fig. K1 / fig. K2 / fig. K3 / fig. K4 / K7). K1 K2 K3 K4 Detils: CT: < 1,8 CM% CA/CAF: < 0,3 CM% Detils: Detils: Begin instlling the first two rows in left-hnd orner of the room t distne to the wll of 8-10 mm, with oth tongue sides of the first element fing the wll nd oth grooved sides fing the instller (fig. K8). The elements of the first two rows my e instlled simultneously, in onstnt lterntion whilst oserving the minimum offset of the short ends re t 20 m, s represented nd desried elow. 6

7 8-10 mm Wll 8-10 mm Element 1 = Instlltion nd pling in left-hnd orner of the room (fig. K8) Element 2 = Angling the long side of this element ut to length. For this purpose, ple the longitudinl tongue t slight ngle from ove into the longitudinl groove of element 1 nd lower the element 2 until it rehes flt position nd press it into the dhesive ed. (fig. K9) Element 3 = Angling the long side nd pressing in the short side. To egin with, return the longitudinl tongue t slight ngle from ove into the longitudinl groove of element 1. Now push element 3 in this ngled position towrds the front of element 2, until the short sides of oth elements push ginst eh other in perfet fit. One gin lok the longitudinl onnetion y lowering nd t the sme time the frontl onnetion y pushing until you n feel them snp into ple, so tht the full surfe of the element is loted in the dhesive ed. (fig. K10) Element 4 = Opposite ngling of the long side nd pressing of the short side s ove. Ple the longitudinl groove t slight ngle under the longitudinl tongue of element 3. Push element 4 in this ngled position towrds the front of element 1, until the short sides of oth elements push ginst eh other in perfet fit. Now one gin lok the longitudinl onnetion y lowering nd t the sme time the frontl onnetion y pushing until you n feel them snp into ple nd the full surfe of the element is loted in the dhesive ed. (fig. K11) Element 5 = Angling the long side nd pressing in the short side s well s pressing into the dhesive ed (see element 3) Element 6 = Angling the long side nd pressing in the short side s well s pressing into the dhesive ed (see element 4) Element 7 = Angling the long side nd pressing in the short side s well s pressing into the dhesive ed (see element 3) Element 8 = Angling the long side nd pressing in the short side s well s pressing into the dhesive ed (see element 4) Instll ll remining elements for the first nd the seond row s desried ove. The lst elements re ut to length. (fig. K12 + K13) K5 K6 K7 K mm K mm K10 K11 K12 K13 Susequently, repply dhesive with the nothed trowel ross the entire length for width of mximum 50 m, so tht the next 2 rows of the Design+ flooring n e instlled one fter the other, one element t time. (fig. K14 + K15) K14 K15 7

8 Instll the first element of the third row y inserting the longitudinl tongue side into the longitudinl groove of the seond row t slight ngle from ove. Then lower the element until it is lying flt nd press it into the dhesive ed. To instll the seond element of the third row, one gin tilt the long edge with the tongue down nd slide it into the groove on the long side of the seond row. With the element in this tilted position, now slide it towrds the end of the first pnel in the third row until the frontl onnetion mehnisms re ove eh other so they re perfetly fitting. Now lok the long edge y lowering the pnel nd the front y pushing until you n feel it lok nd the full surfe of the element is in the dhesive ed. Instll ll remining elements of the third row s desried ove. The lst element is one gin ut to length. All susequent rows re lwys strted with the lst pnel in the preeding row, if it is t lest 200 mm long. You n ontinue to instll element fter element now. In order to prepre the finl row of elements for instlltion, tke the element nd ple it extly on top of the row efore lst. By mens of residul pnel (element width) it is possile to trnsfer the wll strutures to the element within pre-hosen distne. Attention! Mke sure tht the short ends re stggered t lest 200 mm (8 ). In se of produts with evel nd / or with speil pttern (e.g., tiles deor), ensure the offset is even ording to the evel nd / or pttern. The drying nd hrdening time of the respetive dhesive must e oserved efore the instlled EGGER Design + flooring surfe is pproved for use. 8

9 4.2. Floting instlltion (only in privte living re) As generl rule: The su-floor prepred for floor ldding works must e dry, len, free of relese gents, rk-free, level, s well s disply tensile nd ompression strength ording to DIN nd DIN (With regrd to levelness, the inresed requirement of < 2 mm / m must e oserved.) The floor instller must express ny onerns in writing if the su-floor is not redy for instlltion, i.e., if it displys defets or the top floor my e dmged due to the su-floor's struture. If the levelness of the su-floor s required for instlltion is not hieved, preot nd / or filling must e pplied s speifi to the system. In the se of EGGER Design + flooring, the system-speifi EGGER Silenzio Duo underly mt must e used for floting instlltion. When using Silenzio Duo s underly (omintion mt with integrted moisture protetion), no seprte vpour rrier is neessry. Alterntive underlys re ville t (fig. B1). In the se of the floting instlltion of EGGER Design+ flooring in privte living res, the individul ords re loked in ple with the help of the ptented UNI fit! onnetion. Chek the elements for visile dmge / defets. Mke sure you understnd the differene etween the tongue nd the groove on the element (fig. B2 / B3). Begin instlling the first row in left-hnd orner of the room with oth tongue sides of the first element fing the wll nd oth grooved sides fing the instller (fig. B2 / B3). The elements of the first two rows my e instlled simultneously, in onstnt lterntion while oserving the minimum offset of the short ends re t 20 m, s represented nd desried elow m Wll 8-10 mm Element 1 = Instlltion in left-hnd orner of the room (fig. B4) Element 2 = Angling the long side of this element ut to length. For this purpose, ple the longitudinl tongue t slight ngle from ove into the longitudinl groove of element 1 nd lower the element 2 until it rehes flt position. (fig. B4) Element 3 = Angling the long side nd pressing in the short side. To egin with, return the longitudinl tongue t slight ngle from ove into the longitudinl groove of element 1. Now push element 3 in this ngled position towrds the front of element 2, until the short sides of oth elements push ginst eh other in perfet fit. One gin lok the longitudinl onnetion y lowering nd t the sme time the frontl onnetion y pushing until you n feel them snp into ple. (fig. B5) Element 4 = Opposite ngling of the long side nd pressing of the short side s ove. Ple the longitudinl groove t slight ngle under the longitudinl tongue of element 3. Push element 4 in this ngled position towrds the front of element 1, until the short sides of oth elements push ginst eh other in perfet fit. Now one gin lok the longitudinl onnetion y lowering nd t the sme time the frontl onnetion y pushing until you n feel them snp into ple. (fig. B6) Element 5 = Angling the long side nd pressing in the short side (see element 3) Element 6 = Angling the long side nd pressing in the short side (see element 4) Element 7 = Angling the long side nd pressing in the short side (see element 3) Element 8 = Angling the long side nd pressing in the short side (see element 4) Instll ll remining elements for the first nd the seond row s desried ove. The lst elements re ut to length. (fig. B7) Finlly, orientte the first two rows to fe the wlls, s required, while oserving the wll distne (8-10 mm ) to the wll nd ple the spers. (fig. B7 / B8) B1 50 mm B2 B3 B mm m EGGER Silenzio Duo Detils: B5 B6 B mm 8-10 mm B8 9

10 Instll the first element of the third row y inserting the longitudinl tongue side into the longitudinl groove of the seond row t slight ngle from ove. Then lower the element until it is lying flt. To instll the seond element of the third row, one gin tilt the long edge with the tongue down nd slide it into the groove on the long side of the seond row. With the element in this tilted position, now slide it towrds the end of the first pnel in the third row until the frontl onnetion mehnisms re ove eh other so they re perfetly fitting. One gin lok the long edge y lowering the element nd the front y pushing until you n feel it lok. Instll ll remining elements for the third row s desried ove. The lst pnel is one gin ut to length. All susequent rows re lwys strted with the lst pnel in the preeding row, if it is t lest 200 mm long. Continue to instll element fter element now. In order to prepre the finl row of elements for instlltion, tke the element nd ple it extly on top of the row efore lst. By mens of residul pnel (element width) it is possile to trnsfer the wll strutures to the element within pre-hosen distne. Attention! Ensure tht the short ends re stggered t lest 200 mm (8 ). In se of produts with evel nd / or with speil pttern (e.g., tiles deor), ensure the offset is even ording to the evel nd / or pttern. Removl / dismntling of elements for floting instlltion In order to reple instlled pnels without destroying them, first unlok the entire row y tilting it nd then offset the pnels t the ends while they re lying flt. Proeed with due re in order to void dmging the tongue nd groove. B9 B10 B11 B12 10

11 4.3. Instlltion in wet res In wet res, suh s for exmple privte throoms, EGGER Design+ floors enefit from the ptented UNI fit! onnetion, oth glued over the entire re or instlled s floting floor. In se of ommeril pplition res (spe used ommerilly, e.g. throoms in hotel rooms), wet res of use lso require tht EGGER Design+ is lwys glued full-surfe. Definition wet re Rooms with elevted ut not permnent moisture / liquid exposure nd / or periodilly high mient humidity. Exmples of wet res inlude throoms, kithens, hllwys, nd entrne res. Attention! Applitions exlude wet rooms (suh s, for exmple, suns, stem ths, shower ins or ells, ommunity lundry rooms, nd swimming pool res), res with permnent moisture or liquid, s well s ny outdoor re The full-surfe glueing of EGGER Design+ flooring in wet res n e rried out on ll types of sreed, inluding heted sreeds on the sis of hot wter, s well s ermi tiles whih n e onsidered redy for instlltion in view of the requirements outlined under point 2.1. If the levelness of the su-floor s required for instlltion is not hieved, system-speifi preot nd / or filling must e pplied. The sreed must e snded nd spirted with n industril vuum lener. Floor struture: 1) Su-floor (ement sreed, lium sulphte sreed, lium sulphte flow sreed nd their heted sreeds on the sis of hot wter, ermi tiles) 2) Vpour-permele omposite wter-proofing (system-speifi seling nd vpour rrier whih prevents the seeping of the liquid into the onstrution, fig. K17) 3) Adhesive (pproved dhesives see fig. K18) 4) EGGER Design+ Flooring The tul instlltion of the Design+ flooring tkes ple s desried in setion 4.1, where the individul ords re loked with the ptented UNI fit! onnetion. Attention! Only trnsition, djustment, nd end profiles mde of luminium shll e used. The joint etween profile nd wll must e wterproofed with n ryli selnt (silion) (see fig. K23). The drying nd hrdening time of the respetive dhesive must e oserved efore the instlled EGGER Design+ flooring surfe is pproved for use (fig. K21). K16 K17 K18 K19 Drying Time Bthroom Detils: K20 K21 Drying Time K22 K23 SILICONE 25 Detils: 11

12 The floting instlltion of EGGER Design+ flooring in wet res (privte use) n e done on ll types of sreed, inluding heted sreeds on the sis of hot wter, s well s existing floor overings of existing tiles whih n e onsidered redy for instlltion in view of the requirements outlined under point 2.1. Floor struture: 1) Su-floor (ement sreed, lium sulphte sreed, nd heted sreeds on the sis of hot wter, ermi tiles) 2) Underly mt EGGER Silenzio Duo nd EGGER Aqu+ Tpe (seling off wll onnetion res) 3) EGGER Design+ Flooring Attention! It is solutely neessry to ensure the full-surfe instlltion of the system-speifi EGGER Silenzio Duo nd to use EGGER Aqu+ Tpe to sel off the wll onnetion res. B13 The tul instlltion of the Design+ flooring tkes ple s desried in setion 4.2, where the individul ords re loked with the ptented UNI fit! onnetion. The sper tpe integrted in the EGGER Aqu+ Tpe ensures tht the neessry wll distne of 8-10 mm is mintined. After ompleting the instlltion, the sper tpe must e removed. B14 B15 50 mm B16 EGGER Silenzio Duo Detils: B mm m B18 B19 B20 B21 B22 B23 B mm 8-10 mm B mm B26 B27 SILICONE 25 B28 SILICONE 25 Only trnsition, djustment, nd end profiles mde of luminium should e used. The joint etween profile nd wll must e wterproofed with n ryli selnt (silion). 12

13 4.4. Additionl instlltion instrutions Pipes mm 8-10 mm 8-10 mm Mesure the position of the pipes nd mrk on the pnel (llow for edge joint). Drill t lest 16 mm more thn the dimeter of the pipe. Sw to the holes t 45 ngle. Fit nd glue the swn piee. Door frmes = + 16 mm If there re wooden door frmes, it is reommended to shorten them in greement with the lient y the height of the Design + flooring plus glue pplition or underly mterils (fig. 1). Susequently instll the Design + flooring until underneth the door frme leving the neessry expnsion gp. For esy instlltion t door frmes, the respetive element n e ngled y length nd lowered. Susequently, the element pled flt on the floor is pushed under the door frme nd the frontl onnetion is loked through horizontl knoking with hmmer nd tpping lok. (fig ) For door frme whih nnot e shortened, e.g. mde of metl, we reommend to lose or over the expnsion gps with selnt or suitle end profiles. (fig. 2) Inserting floor profiles nd skirting ords Instll the required floor profiles nd the skirtings fter the Design + flooring hs een properly instlled s desried ove. Simple ssemly instrutions re enlosed with ll the essories. Attention! With most profile types, the se (su-profile) to the over profile must e instlled prior to instlling the floor. In the se of speil instlltion ses, e.g., stirs, or for other tehnil questions, plese ontt your retil prtner or the tehnil Customer Servie of EGGER Retil Produts GmH & Co. KG. 13

14 5. Clening nd Mintenne Simply len! Most dirt n lredy e kept out y hving pproprite doormts or len-off zones in the entrne re. For the rest, use the rush tthment on the vuum lener. Depending on the frequeny of use nd mount of dirt, you should lso wipe the floor regulrly with dmp loth. Cre should e tken to len the evels in longitudinl diretion. For optimum lening we reommend Clen-it, the EGGER system flooring lener. Optiml re nd protetion for the EGGER Design+ flooring! Entrne res must e fitted with properly sized len-off zone / doormt. In the se of ommeril pplitions where the EGGER Design + re leds diretly outside, n ppropritely sized len-off zone should e uilt into the floor struture. Lift furniture when moving, rther thn pushing or drgging. Atth felt pds to the feet of furniture, inluding hirs nd tles. Clen these regulrly, hek for proper funtionlity nd reple if required. Use soft furniture stors (type W) in the se of offie hirs nd ll other ojets on stors. Clen offie hir nd furniture stors regulrly, hek for proper funtionlity nd reple if required. Use the hrd floor nozzle when vuum lening. Clen the Design + with dmp loth only. Do not let puddles / splsh (wet) or moisture dry off, ut rther wipe them dry s soon s possile (within 1 hour). Do not use residue uilding lening produts. We reommend our system-relted flooring lener Clen-it from EGGER. When using regulr stem lener, it is neessry to keep the mhine onstntly moving. The stem lener should only e filled nd operted with len wter. Do not dd lening produts or other dditives. Never use rsives or souring gents on the EGGER Design + floor. Wxing nd / or polishing is not neessry, nor permitted. Full-surfe seling of the EGGER Design + flooring during use is not neessry, nor permitted. *The EGGER Design+ Flooring wrrnty terms pply, whih re ville from your distriutor or to downlod on the Internet. 14

15 Notes 15

16 EGGER Retil Produts GmH & Co. KG Im Kissen Brilon Germny t f flooring@egger.om EN_EGGER_Design+_Fußoden_Verlegenleitung_11/2016 Sujet to tehnil modifitions nd error. Advie, servie nd more: