CONTACT LIST DOORS IN THE PATH OF EGRESS TRAVEL SHALL MEET THE REQUIREMENTS OF ICC / ANSI A117.1 : SECTION MANEUVERING CLEARANCES AT DOORS

Size: px

Start display at page:

Download "CONTACT LIST DOORS IN THE PATH OF EGRESS TRAVEL SHALL MEET THE REQUIREMENTS OF ICC / ANSI A117.1 : SECTION MANEUVERING CLEARANCES AT DOORS"

Baldwin Jones
6 years ago
Views:

1 DOORS TO EXTERIOR HAVE CLOSURES & LATCHES AND MEET THE REQUIREMENTS OF ICC / ANSI A7. : SECTION DOOR HARDWARE SECTION CLOSING SPEED SECTION DOOR OPENING FORCE SECTION TRESHOLDS DOORS IN THE PATH OF EGRESS TRAVEL SHALL MEET THE REQUIREMENTS OF ICC / ANSI A7. : SECTION MANEUVERING CLEARANCES AT DOORS ALL EGRESS DOORS SHALL BE ACCESSIBLE PROVIDING A MINIMUM OF TWO ACCESSIBLE MEANS OF EGRESS FROM BUILDING AS REQUIRED BY ICC SECTION 007. CONTACT LIST ARCHITECT SCHILLACI ARCHITECTS LTD. E.TROUT RUN RD. EPHRATA, PA MARK SCHILLACI SCHILLARCS@GMAIL.COM STRUCTURAL ENGINEER EAGLE ENGINEERING COLUMBIA, PA MITCH WEAVER eagleengineering00@gmail.com MEP EVOLUTION BUILDING SERVICES, LLC LANCASTER, PA TODD POSTLETHWAIT toddmepdesign@comcast.net

4 GENERAL :. THE MECHANICAL SYSTEM INDICATED ON THE DRAWINGS ARE GENERALLY DIAGRAMMATIC TO SHOW THE OWNER'S INTENT AND THE MECHANICAL EQUIPMENT LOCATIONS. ALL EQUIPMENT AND ACCESSORIES ARE SHOWN APPROXIMATELY AND SHALL BE INSTALLED CONSISTENT WITH JOB CONDITIONS AND APPLICABLE CODE REQUIREMENTS. THE HVAC CONTRACTOR SHALL PROVIDE ALL LABOR AND MATERIALS NECESSARY FOR A COMPLETE WORKING SYSTEM AND ALL FINAL DESIGN OF THE COMPLETE MECHANICAL SYSTEM. THE MECHANICAL CONTRACTOR SHALL BE RESPONSIBLE FOR SEALED PERMIT DRAWINGS AND PERMIT COSTS. 2. THE MECHANICAL DESIGN AND INSTALLATION SHALL MEET ALL THE REQUIREMENTS OF THE AUTHORITY HAVING JURISDICTION. IT SHALL ALSO MEET THE 2009 INTERNATIONAL BUILDING CODES, ASHRAE 2007 STANDARD 90., NPFA CODES, ENERGY CODES AND THE NATIONAL ELECTRIC CODE. 3. THE MECHANICAL CONTRACTOR SHALL EXAMINE THE ARCHITECTURAL DRAWINGS AND SITE TO FULLY INFORM ITSELF OF ALL CONDITIONS. 4. THE MECHANICAL CONTRACTOR SHALL BE RESPONSIBLE FOR PROVIDING ALL CONDENSATE DRAINS. 5. THE MECHANICAL CONTRACTOR SHALL PROVIDE A TRAINING WALK THROUGH WITH THE OWNER AND GENERAL CONTRACTOR TO DISCUSS ALL HVAC COMPONENTS AT THE CONCLUSION OF THE PROJECT. 20 CFM 4"o FR- 35 CFM 0 CFM 05 CFM 6. THE MECHANICAL CONTRACTOR SHOULD SUBMIT AS - BUILT DRAWINGS AND O & M MANUALS AT THE CONCLUSION OF THE PROJECT. 7. ALL OCCUPIED SPACES SHALL MEET THE NATURAL VENTILATION REQUIREMENTS OF THE 2009 INTERNATIONAL MECHANICAL CODE SECTION INSTALL ALL EQUIPMENT AND ACCESSORIES PER THE MANUFACTURER INSTRUCTIONS. ALLOW THE MANUFACTURERS RECOMMENDED CLEARANCE AROUND ALL COMPONENTS. 9. ALL TUBING AND FITTINGS SHALL BE RATED AND LISTED FOR APPLICATION OF USE. VERIFY THE PROPER PRODUCT TYPE IS LISTED FOR ITS INTENDED USE. 0. IT IS THE CONTRACTOR'S RESPONSIBILITY TO PROVIDE A COMPLETE WORKING SYSTEM. THESE DRAWINGS ARE FOR THE SYSTEM INTENT PER THE OWNER. SYSTEM INSTALLATION, DESIGN, ENGINEERING AND OPERATION IS THE SOLE RESPONSIBILITY OF THE MECHANICAL CONTRACTOR.. ALL HVAC DUCTWORK SHALL BE GALVANIZED G90 SHEET METAL AND SHALL MEET THE MINIMUM REQUIREMENTS OF THE LATEST EDITION OF THE SMACNA DUCTWORK CONSTRUCTION STANDARDS. THE DUCTWORK SHALL BE EXTERNALLY WRAPPED WITH BLANKET R-6 INSULATION. 20 CFM FR- 20 CFM 2x22 RETURN DUCT RR- 050 CFM T RR-2 25 CFM CU 2. ALL BRANCH SUPPLY AND RETURN GRILLES SHALL HAVE VOLUME DAMPERS TO BALANCE EACH AIR DEVICE OUTLET. 3. ALL DUCTWORK ELBOWS AND TEES SHALL HAVE TURNING VANES INSTALLED TO MINIMIZE STATIC PRESSURE DROP. 20x20 DUCT ABOVE DOOR TO RR- (2)2x8 UP & DN 4. EXISTING BOILER, BOILER PIPING AND RADIATOR FOR REUSE. WALL HEATER SCHEDULE LABEL (ID) WH- MAKE QMARK MODEL AWH4408 KW 2.0 VOLTAGE 208 PH AMPS 9.6 SEE BELOW : PROVIDE WITH MOUNTING HARDWARE AND INTEGRAL T-STAT. ELECTRIC BASEBOARD HEAT SCHEDULE 5 CFM CAN 20x20 DUCT FIT BELOW CEILING AND ABOVE CLOSET DOOR? IF NOT WOULD THE SECONDARY LOCATION WORK? FR-4 65 CFM LABEL (ID) MAKE MODEL LENGTH WATTS VOLTAGE PH AMPS - QMARK 2542W 2'-0" SEE BELOW -2 QMARK 2544W 4'-0", SEE BELOW : PROVIDE WITH UNIT MOUNTED INTEGRAL T-STAT. 5 CFM 5 CFM FR-2 80 CFM WH FR-4 65 CFM EXHAUST FAN SCHEDULE LABEL (ID) MAKE MODEL CFM S.P. VOLTAGE PH AMPS WATTS(HP) DISCHARGE - BROAN QTRE0FLT " " SEE NOTE, 2, 3, 4 :. EXHAUST FANS SHALL HAVE BACKDRAFT DAMPERS. 2. PROVIDE WITH ANY NECESSARY DUCT TRANSITIONS & NEOPRENE ISOLATERS. 3. PROVIDE WITH WALL CAP OR ROOF JACK. 4. PROVIDE WITH ALL ACCESSORIES NECESSARY FOR A COMPLETE INSTALLATION. AIR CONDITIONER SPLIT SYSTEM SCHEDULE LABEL (ID) MAKE MODEL(INDOOR UNITS) HP VOLT PH AMPS FUSE MODEL (OUTDOOR) TON SEER VOLTAGE PH MCA MOCP AHU-/CU- GOODMAN ASPT06D4 208/ GSX / AMP SEE :. PROVIDE SPLIT SYSTEM WITH LOW AMBIENT KIT, HARD START KIT, CRANKCASE HEATER AND 7 DAY PROGRAMMABLE THERMOSTAT. AIR DEVICE SCHEDULE LABEL (ID) MAKE MODEL SIZE NECK CFM DESCRIPTION FR- HART & COOLEY "x FLOOR DIFFUSER PROVIDE WITH BRANCH AND INTEGRAL DAMPER FOR BALANCING FR-2 HART & COOLEY 4 4x HART & COOLEY 4 6x FLOOR DIFFUSER FLOOR DIFFUSER PROVIDE WITH BRANCH AND INTEGRAL DAMPER FOR BALANCING PROVIDE WITH BRANCH AND INTEGRAL DAMPER FOR BALANCING FR-4 HART & COOLEY 4 6x FLOOR DIFFUSER PROVIDE WITH BRANCH AND INTEGRAL DAMPER FOR BALANCING CD- HART & COOLEY A502 0x WAY OPPOSITE CEILING GRILLE - TG- RR- RR-2 HART & COOLEY A650 4x TRANSFER GRILLE - HART & COOLEY RHD45 20x HIGH WALL RETURN PROVIDE WITH TAMPER PROOF VOLUME DAMPER HART & COOLEY RHD45 2x HIGH WALL RETURN PROVIDE WITH TAMPER PROOF VOLUME DAMPER :. COORDINATE AIR DEVICE QUANTITY, THROW, SIZE, AND CEILING TYPE HARDWARE BORE ORDERING. 2. EXAMINE EXISTING CONDITIONS BORE ORDERING AIR DEVICES. OIL BURNER EMERGENCY SHUTOFF SWITCH MEETING ALL REQUIREMENTS OF THE 2009 IMC SECTION DS (2)TG- CD- 65 CFM 6"o 4x6 TRANSFER THRU WALL CD- 65 CFM 6"o (2)RR CFM EACH COORDINATE CHASE W/ ARCHITECT 20x8 5"o 20x0 20x0 5"o 20x2 AHU 20x8 2x22 UP (2)2x8 UP (3)CD- 25 CFM EA. (2)TG- 4x6 TRANSFER THRU WALL FR- 30 CFM 4"o UP THRU ROOF (2) 2x8 RETURN DROPS DOWN FR-2 80 CFM 5"o EXISTING OIL BOILER FOR HEATING PROVIDE ADD ALTERNATE TO ZONE FIRST AND SECOND FLOORS. 6"o

5 NOTE: PROVIDE CEILING FAN RATED BOXES FOR NEW CEILING FANS. NOTE: ALL CIRCUITS THAT ARE EXISTING TO BE RE-USED A- A- A- A- A- A- A- A- NEW FAN A- A- A- A- A- NEW FAN OPEN DOOR BUTTON A- A-3 A- A- A- A- A-0 8,30 A-0 A-0 A-4 PROVIDE ALL LOW VOLTAGE WIRING THROUGH DOOR FRAME AS REQUIRED. A-5 A- WH A-7,9 A- A- A- A-0 A-4 A- A- NEW FAN NEW FAN A-0 A- A- A- A-0 A-0 A-6 A-0 A- CU A-34,36 A- A- A- A- A- NOTE: PROVIDE CEILING FAN RATED BOXES FOR NEW CEILING FANS. NOTE: ALL CIRCUITS THAT ARE EXISTING TO BE RE-USED A- NEW FAN A- A- 4,26 A-3 A- 4,26 A- A- A- 2 A- A-38,40 A-5 A- A- A-6 20V TO BPS POWER SUPPLY FOR DOOR OPENING DEVICE BELOW DESK. A- GENERAL :. THE ELECTRICAL SYSTEM LAYOUTS INDICATED ON THIS DRAWING IS DIAGRAMMATIC IN AN FORT TO SHOW THE OWNERS INTENT THE CONTRACTOR SHALL SURVEY AND VERIFY ALL EXISTING CONDITIONS ON SITE. 2. THE CONTRACTOR SHALL VERIFY THE NUMBER AND LOCATION OF ALL OUTLETS, LIGHTING BASEMENT LIGHTS CIRCUIT A-3 AHU A-3 FIXTURES AND EQUIPMENT. 3. THE ENTIRE ELECTRICAL INSTALLATION SHALL MEET THE REQUIREMENTS SET FORTH BY THE 2008 NATIONAL ELECTRIC CODE AND ANY OTHERS REQUIREMENTS BY THE AUTHORITY HAVING JURISDICTION. 4. THE ENTIRE INSTALLATION SHALL BE IN COMPLIANCE WITH APPLICABLE OSHA, FEDERAL, STATE, ANSI, NEMA, NFPA AND MUNICIPAL LAWS AND REGULATIONS. 5. CONNECT ALL EMERGENCY LIGHTING AHEAD OF LOCAL LIGHTING CIRCUITS. 6. ALL ELECTRICAL COMPONENTS AND DEVICES SHALL BE UL LISTED. 7. COORDINATE LOCATIONS OF RECEPTACLES, LIGHTING AND SWITCHES BORE INSTALLATION. 8. ALL EXPOSED CONDUIT SHALL MEET THE REQUIRES SET FORTH BY THE 2008 NEC STANDARDS. 9. SEE HVAC AND PLUMBING PLANS FOR EQUIPMENT LOADS. 0. THE ELECTRICAL CONTRACTOR SHALL PROVIDE ALL LABOR AND MATERIALS NECESSARY FOR A COMPLETE WORKING SYSTEM AND ALL FINAL DESIGN OF THE COMPLETE ELECTRICAL SYSTEM.. EXISTING BASEMENT RECEPTACLES SHALL REMAIN FOR REUSE RECONNECT CIRCUITS TO NEW PANEL AS REQUIRED. 2. REPLACE EXISTING INTERIOR LIGHT SWITCHES WITH OCCUPANCY SENSOR LIGHT SWITCHES TO A-3 A-32 2-/2" CONDUIT TO UTILITY POLE. CONDUCTORS BY PPL. MEET THE 2009 INTERNATIONAL ENERGY CONSERVATION CODE SECTION & ALL NEW LIGHTING SWITCHES SHALL ALSO BE OCCUPANCY SENSOR LIGHT SWITCHES. 2" CONDUIT WITH (3)4/O AL ()#4 AL * CONFIRM AIC RATING WITH UTILITY PROVIDER NEW 200A -PH SELF CONTAINED METER BASE A-3 EXISTING OIL BOILER FOR REUSE. NEW 42 SPACE 200 AMP SERVICE AND PANEL A NOTE: RECIRCUIT EXISTING LOADS AND SUBPANELS IN BASEMENT TO NEW PANEL A. PROVIDE BREAKERS AS REQUIRED FOR EXISTING LOADS. NEW 200 AMP PH SELF CONTAINED METER BASE PANEL A 200A MCB 20/240V, PH 3 WIRE 22K AIC* A-3 #4 CU BOND METAL WATER PIPE AND ANY OTHER INCOMNING UNDERGROUND METAL PIPES #6 CU TO (2)GROUND RODS MIN. 6' APART

6 GENERAL PLUMBING :. THE PLUMBING LAYOUT INDICATED ON THE DRAWINGS IS DIAGRAMMATIC IN AN FORT TO SHOW THE DESIGN INTENT. 2. THE PLUMBING CONTRACTOR FOR SHALL INSPECT AND ACQUAINT THEMSELVES WITH THE PROJECT CONDITIONS IN ORDER THAT HE FULLY UNDERSTAND THE WORK REQUIRED. HE SHALL FIELD MEASURE AND VERIFY ALL DIMENSIONS AND CONDITIONS BORE PROCEEDING WITH THE WORK. 3. ALL PLUMBING WORK SHALL CONFORM WITH THE PENNSYLVANIA STATE UNIFORM CONSTRUCTION CODE, STATE BARRIER FREE REQUIREMENTS, THE 2009 INTERNATIONAL PLUMBING CODE (I.P.C.) AND THE INTERNATIONAL FUEL GAS CODE (IFGC). 2" 2" 2" DOWN 4. THE PLUMBING CONTRACTOR SHALL VERIFY ALL LOCATIONS AND ELEVATIONS OF EXISTING SERVICES AND UTILITIES BORE STARTING ANY WORK. REPORT ANY DISCREPANCIES TO THE ARCHITECT FOR A RESOLUTION. 2"CW T- 5. THE PLUMBING CONTRACTOR SHALL REPLACE ANY PIPING SYSTEM COMPONENTS WHICH DO NOT PASS TESTING PROCEDURES SPECIFIED AND RE-TEST REPAIRED PORTIONS OF THE SYSTEM. 6. ALL WORK AND MATERIAL SHALL HAVE A GUARANTEE AND BE FREE FROM DECTS FOR A PERIOD OF ONE YEAR AFTER THE COMPLETION OF THE PROJECT, DURING WHICH ALL REPAIRS SHALL BE MADE AT NO COST TO THE OWNER. 2"CW 2"HW S- 2" VTR. -/2"S DOWN 7. COORDINATE ALL WORK WITH THE GENERAL CONSTRUCTION & THE OTHER TRADES. 8. PIPING LAYOUTS ARE DIAGRAMMATIC AND INTENDED TO SHOW GENERAL ARRANGEMENT, SIZE AND CAPACITY. ALL OFFSETS ARE NOT NECESSARILY SHOWN. THE PLUMBING CONTRACTOR SHALL ARRANGE AND COORDINATE THE WORK, FURNISH NECESSARY OFFSETS, VALVES, VENTS, ACCESS DOORS, CLEAN OUTS AND FITTINGS TO AVOID CONFLICTS WITH OTHER MECHANICAL AND ELECTRICAL SERVICES AND WITH STRUCTURAL AND ARCHITECTURAL ELEMENTS. 9. ALL CONCRETE FLOOR, WALL, AND FOOTING PENETRATIONS SHALL BE MADE WITH CORE DRILLED HOLES. SAWCUT & REMOVAL BY OTHERS. 0. SEE ARCHITECTURAL PLANS FOR MOUNTING HEIGHTS OF ALL PLUMBING FIXTURES.. RER TO ARCHITECTURAL DRAWINGS FOR EXACT LOCATION OF ALL HANDI-CAP FIXTURES. MOUNT THESE FIXTURES IN ACCORDANCE WITH THE STATE ADOPTED BARRIER FREE SUBCODE WITH RESPECT TO SUCH ASPECTS AS MOUNTING HEIGHT, DISTANCE FROM GRAB BARS, LOCATION OF HAND CONTROLS, CLEARANCES, ETC. 2. ALL SANITARY PIPING TO PLUMBING FIXTURES SHALL BE CAST IRON PIPE TO MATCH EXISTING OR SCH 40 PVC. PIPE SIZE SHALL BE AS INDICATED ON DRAWINGS. ALL DOMESTIC WATER SHALL TO BE COPPER PIPE TO MATCH EXISTING. 3. PROVIDE INDIVIDUAL SHUT-OFF VALVES AT ALL WATER CONNECTIONS TO FIXTURES AND EQUIPMENT. 4. THE PLUMBING CONTRACTOR SHALL INSTALL PIPING SO AS NOT TO ENCROACH ON REQUIRED CLEARANCES ABOVE ANY ELECTRIC PANEL/SWITCHBOARDS. NO PIPING SHALL BE INSTALLED DIRECTLY OVER ELECTRICAL PANELS AND NO PIPING SHALL BE INSTALLED WITH THE BOTTOM AT LESS THAN 6'-6" ABOVE THE WORKING SPACE IN FRONT OF ANY ELECTRIC PANELS/SWITCHBOARDS. PLUMBING: SYMBOL CW HW HWR CO FD S WH W V UTR DESCRIPTION WALL HYDRANT COLD WATER SUPPLY PIPING HOT WATER SUPPLY PIPING HOT WATER RECIRCULATING PIPING CLEAN OUT FLOOR DRAIN SANITARY WALL HYDRANT SANITARY WASTE VENT UP THRU ROOF HOT WATER RECIRC PUMP HW DN TO BASEMENT -/2"S UP TO S-2 UP TO T-2 HW 5. THE PLUMBING CONTRACTOR SHALL MAKE ALL FINAL CONNECTIONS TO ALL FIXTURES AND EQUIPMENT UNLESS OTHERWISE NOTED. 6. PROVIDE ACCESS DOORS IN WALLS AND CEILINGS AS REQUIRED TO MAKE VALVES, WATER HAMMER ARRESTERS, TRAP PRIMERS, ETC. READILY ACCESSIBLE. COORDINATE LOCATION OF ACCESS DOOR WITH INSTALLATION OF VALVES, WATER HAMMER ARRESTERS, TRAP PRIMERS, ETC. IN FIELD DURING CONSTRUCTION. 7. ALL BACK FLOW PREVENTION DEVICES SHALL BE ACCESSIBLE AND SHALL INCLUDE A STRAINER AND ISOLATING VALVES UNLESS OTHERWISE INDICATED. DOUBLE CHECK VALVES AND REDUCED PRESSURE ZONE VALVES SHALL BE INSTALLED AT NOT LESS THAN 2" ABOVE THE FLOOR AND A MAXIMUM OF 60" ABOVE THE FLOOR. S-3 STUDOR VENT BELOW. -/2" S DOWN. 8. THE PLUMBING CONTRACTOR SHALL MAKE ALL FINAL CONNECTIONS TO SANITARY LATERALS INSTALLED BY SITE CONTRACTOR. 9. ALL VENT PIPING SHALL BE SLOPED TO DRAIN BACK TO THE DRAINAGE SYSTEM. 20. ALL MATERIAL, EQUIPMENT AND ACCESSORIES SHALL BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER'S WRITTEN INSTALLATION INSTRUCTIONS. COORDINATE EXACT LOCATIONS TO ACCOMMODATE ALL REQUIRED CLEARANCES AND OBSERVE ALL REQUIREMENTS FOR VALVING AND CONNECTIONS. 2. SEE PLUMBING SCHEDULE FOR BRANCH MINIMUM PIPE BRANCH SIZES. 22. REUSE WATER, VENT AND DRAIN LINES WHERE POSSIBLE. PROPERLY CAP PIPING NOT BEING REUSED. VERIFY THAT ALL BUILDING FIXTURES ARE CONNECTED PROPERLY WITHOUT LEAKS. 23. POTABLE WATER SHALL BE TESTED IN ACCORDANCE WITH THE 2009 INTERNATIONAL PLUMBING CODE SECTION THE EXISTING EXTERIOR HOSE FAUCET ON THE WEST WALL NORTH CORNER SHALL FOR USE. 25. THE PLUMBING CONTRACTOR SHALL PROVIDE ALL LABOR AND MATERIALS NECESSARY FOR A COMPLETE WORKING SYSTEM AND ALL FINAL DESIGN OF THE COMPLETE PLUMBING SYSTEM. THE PLUMBING CONTRACTOR SHALL BE RESPONSIBLE FOR SEALED PERMIT DRAWINGS AND PERMIT COSTS. 2" VENT UP THRU ROOF SEE NOTE 24 3" UP TO T- EXISTING SANITARY -/2"S UP TO S- 3" TIE INTO EXISTING HW 3" TIE INTO EXISTING HW UP T-2 S- 2"HW 2" VENT UP THRU ROOF -/2"S DOWN 2"CW DOWN 2"CW UP 3 4"CW FROM 2ND FLOOR TOILET ROOM -/2"S 3 4"HW REUSED EXISTING INDIRECT DOMESTIC HEAT EXCHANGER. 2"HW EXISTING WATER SOFTENERS FOR REUSE. -/2" UP TO S "CW

CONSTRUCTION DOCUMENTS NECESSARY FOR PLAN REVIEW

CONSTRUCTION DOCUMENTS NECESSARY FOR PLAN REVIEW 2012 International Residential Code 2012 International Building Code 2012 International Fire Code 2014 NFPA 70 National Electrical Code 2012 International Existing Building Code 2012 International Plumbing