I-GUIDE SAFEPASS ROAD BARRIER SAFETY SOLUTIONS JONSEREDS 1/12 IG-SAFEPASS ROAD BARRIER-1710
|
|
- Joseph Hunter
- 6 years ago
- Views:
Transcription
1 I-GUIDE SAFEPASS ROAD BARRIER IG-SAFEPASS ROAD BARRIER /12
2 SAFEPASS GENERAL About SafePass Road Barrier SafePass Road Barrier is intended for use as work zone protection where a longitudinal road barrier is required. SafePass Road Barrier is tested according to the European standard EN 1317, containment level T3. General requirements! Always do an assessment and a method statement for the installation.! Perform a safety inspection on products before use.! Never use damaged or rusty materials.! Use tools intended for the installation.! Use lifting equipment with sufficient load capacity.! Use adequate personal protection equipment.! Use personal fall arrest equipment when working at height.! Installation and handling of the road barrier shall be done by trained, competent personnel.! Safety Solutions Jonsereds (SSJ) product liability only applies to combinations of SSJ products that are assembled according to SSJ s I-guides.! No design changes may be made without consulting SSJ.! Make sure all documentation needed is available and up-to-date. Safety recommendations Road barrier systems are often installed in dangerous circumstances with live carriage near by. Make sure national safety regulations are followed when working with the road barrier! SSJ recommend that an adequate safety zone between the working area and the carriage way is maintained during installation/dismounting. Never work alone! 2/12
3 SAFEPASS GENERAL System specification Contaiment level Working width class Working width (W) Dynamic deflection Impact Severity Level (ASI) MIN installation length End anchoring Radii capacity MAX height difference at joint T3 W3 1,0 m 0,5 m A 57 m YES R105 m 4,5 cm W 3/12
4 Ø25 Ø SAFEPASS ROAD BARRIER SafePass Road Barrier 5,16 m Galvanized kg SafePass Road Barrier End Element Galvanized 800 kg Anchor Nail Galvanized 1,4 kg 300 4/12
5 SAFEPASS STORAGE & HANDLING Stacking/storage/transport The barrier units can be stacked on top of each other by letting the feet rest in the service channels of the underlying barriers. Thus, no stacking material is needed. Make sure that the elements in the bottom layer are placed parallel, and as close together as possible. Make sure that all barriers stands firmly, and that all barrier feet are fully engaged into the underlying barriers. Stack a maximum of 3 levels. Beware of crush and tipping risks when handling and stacking the barriers act accordingly. Always secure the barriers during transportation. MAX x 3 Handling The SafePass Road Barrier can be handled using boom trucks, excavators, wheel loaders or fork lifts. Lifting points for forks, 2 leg chain sling, lifting clamp and webbing sling are available. SSJ recommend handling using a lifting clamp or forks this way, work at height can be avoided. To avoid exceeding safe working load limits - never lift interconnected barriers. 5/12
6 SAFEPASS INSTALLATION Prerequisites Installation shall be carried out according to national regulations plan the work site accordingly. Prepare underground SafePass Road Barrier is intended for use on cold asphalt. Make sure that the surface is free of any sand, soil etc that could affect the surface friction properties. Height differences exceeding 4,5 cm around the butt joint area must be evened out before installation. Prepare installation Activate the connector by pulling the handle. (This may be done while the barriers are still stacked). 6/12
7 SAFEPASS INSTALLATION Connect barriers The barrier units are easily connected by letting the connector engage over the locking pin in the end of the next of barrier. Attention do not stand by the joint area if needed, the person on the ground can assist guiding the element from the far end. Make sure that the handle has completely fallen down. The barrier elements should be separated as much as possible after interconnection is done. Move the connector SafePass Road Barrier can be mounted in any direction. If the connector is located at the wrong end, there is no need to turn the barrier around simply move the connector to the other end. 7/12
8 Ø22 SAFEPASS INSTALLATION End anchoring The installed road barrier system shall be anchored in each end. Connect end elements to standard barrier elements. Drill 8x Ø22 mm holes through the anchoring plates (4 in each end). Thereafter, drive anchor nails into each hole. 8 x 8/12
9 SAFEPASS DISMOUNTING Loosen end element Loosen the anchor nails using for instance a crowbar. All pinholes in the carriageway must be restored after removal! Disengage connector and remove barriers Disengage all connectors by lifting the handle and then sliding the connector back. Thereafter remove the barriers. Start by lifting the barriers sideways to avoid damaging/hitting the connector in the next barrier. 9/12
10 SAFEPASS CREATE AN OPENING Create an opening Remove the connectors completely from both sides of the barrier to be removed. Thereafter the element can be removed. Pay attention to if the elements are somewhat jammed together risk of exceeding safe working load limits if adjacent barriers come along when lifting. Close opening Put the barrier element back in to place and re-engage the connectors. 10/12
11 SAFEPASS INSPECTIONS & MAINTANENCE Final inspection When installation is completed, a final safety inspection shall be carried out. The inspection shall be performed using the control guide C-Guide SafePass Road Barrier. Regular inspections Regular inspections shall be carried out, preferably on a daily basis. The C-Guide SafePass Road Barrier can be used as a basis for the inspection. Inspection after impact If an impact has occurred, the barrier system must be inspected. Inspection and any repairing/disposal shall be carried out by competent personnel, using the general maintenance guide M-Guide SafePass Road Barrier General in combination with the product specific M- Guides. Recycling Products or part of products shall be recycled to the extent possible. 11/12
12 SAFEPASS CONTACT Tecnichal support For further information, please contact us: Safety Solutions Jonsereds AB Lägervägen 3 SE Frösön, SWEDEN Tel +46 (0) jonsereds.com 12/12
Instruction Guide. FreeSpan SR. English
English Instruction Guide 7EN130103-01 2007-05-11 FreeSpan SR FreeSpan SR is a freestanding lift system that is intended for use with Liko s Multirall or Likorall lift units. It consists of three main
More informationInstallation. Natrix
Installation Natrix Table of Contents 1 Prerequisites for Installation Site... 2 1.1 On-site Delivery and Insertion at Ground Level... 2 1.2 On-site Delivery and Insertion via Ramp... 2 1.3 Intermediate
More informationCOMBISAFE Multibox 9541 Multibox End Panel USER INSTRUCTIONS _001
COMBISAFE 9540 Multibox 9541 Multibox End Panel 9540-9541_001 USER INSTRUCTIONS Contents 9540 Multibox 9541 Multibox End Panel Contents GENERAL INFORMATION... 3 TECHNICAL DATA... 4 Lift Angles... 4 Internal
More informationStrengthened Soil Wall Construction Manual
Strengthened Soil Wall Construction Manual This information has been prepared by Shaw Technologies, Inc. as an aid in constructing their Strengthened Soil Wall system. Final determination of the suitability
More informationArmorZone TL-2 Barrier
ArmorZone TL-2 Barrier Product Manual ANOTHER AMORFLEX DEVELOPMENT Table of contents Introduction 3 System overview 3 Before installation 3 Limitations and warnings 4 Safety statements 4 System design
More informationProduct Manual Release 05/17
Temporary Safety Barrier (TL-2 MASH) Product Manual VHD (v3) www.valmonthighway.com Table of Contents 1.0 ArmorZone Introduction... 3 2.0 Before Installation... 3 3.0 Limitations & Warnings... 3 4.0 System
More informationNiklas portable freestand
USER`S MANUAL Niklas portable freestand The Niklas portable freestand offers you the unique possibility to lift and move a patient easily and safely without straining the patient or the caregiver. The
More informationInstallation Manual. Orion. TL-3 Steel Barrier. VHD (v2)
Installation Manual Orion TL-3 Steel Barrier VHD (v2) 300914 Table of Contents Orion Introduction.......... 3 Limitations & Warnings. 4 Before Installation..... 3 System Design & Design Considerations
More informationEdge Support Trench Lining System
User Guide Conquip Trench Box Edge Support Trench Lining System Introduction The Conquip 3.5m Trench Box is a simple to assemble, two sided trench lining support system designed to be installed by an excavator
More informationArmorZone TL-2 Barrier and End Treatment
ArmorZone TL-2 Barrier and End Treatment Product and Installation Manual ANOTHER AMORFLEX DEVELOPMENT Table of contents Introduction 3 System Overview 3 Before Installation 3 Limitations and Warnings 4
More informationTable of contents. 1.0 Assembly procedure for pallet live storage Supplemental information for "VARIOFIX" roller conveyor system - 2 -
Table of contents Page 1.0 Assembly procedure for pallet live storage - 2-1.1 Supplemental information for "VARIOFIX" roller conveyor system - 2-1.2 Information on alignment and test run - 3-2.0 Operating
More informationTrench Box. Important Notes. Introduction. User Guide
User Guide Trench Box Introduction The Conquip 3.5m Trench Box is a simple to assemble, two sided trench lining support system designed to be installed by an excavator using the dig and push technique,
More informationTEMPORARY EDGE PROTECTION SYSTEM DESCRIPTION CTS. Combisafe International AB
TEMPORARY EDGE PROTECTION SYSTEM DESCRIPTION CTS Combisafe International AB CTS Combisafe International AB Contents Safety instructions... 3 Important... 4 General... 4 Data... 5 Safety posts 4140/4145/4150...
More informationUSER S Manual. HAKI Bridge System (HBS)
USER S Manual HAKI Bridge System (HBS) HAKI AB 2018 Important information HAKI s product liability and user s manuals apply only to scaffolds that are entirely composed of components that have been made
More informationis generally suitable for trench depths of up to 7.16m, widths of up to 3.92m, pipe lengths of up to 3.0m and a pipe OD of up to 2.6m.
MGF Trench Box Description Simple to assemble, robust, two sided mechanical excavation support system designed to be installed by an excavator utilising the dig and push or excavate and lower in place
More informationAR SCAFFOLDING AR ALUMINUM MOBILE AR STEEL MOBILE
SAFETY RULES and INSTRUCTIONS FOR AR SCAFFOLDING AR ALUMINUM MOBILE AR STEEL MOBILE INTERIOR or EXTERIOR USE ! WARNING! Improper assembly, dismantling or use of Multi-Use Scaffold may result in serious
More informationMGF TECHNICAL FILE TRENCH BOXES. Description. Product Notes.
Description Simple to assemble, robust, two sided mechanical excavation support system designed to be installed by an excavator utilising the dig and push or excavate and lower in place techniques. Normally
More informationBOH FPU Systems BOH ENVIRONMENTAL LLC Avion Parkway, Suite 220 Chantilly, VA POC Jim Stokes (703)
FPU SYSTEMS OPERATION MANUAL BOH QUADCON MODULES, ADAPTERS and RESTRAINT SYSTEM BOH FPU Field Pack/up Units (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH FPU Systems BOH ENVIRONMENTAL LLC 14520 Avion
More informationCreated by EBCCW 00:06. X65 Locating module. User Documentation
Created by EBCCW 00:06 by EBCCW 96:05 00:06 X65 Locating module User Documentation Created by EBCCW 96:05 00:06 Created by EBCCW 00:06 by EBCCW 96:05 00:06 X65 Locating module Created by EBCCW 96:05 00:06
More informationS-60-MI2 : 500kg mini tower system v.2
S-60-MI2 : 500kg mini tower system v.2 INSTRUCTION MANUAL ALC Truss S-60-MI2 Mini Tower v.2 Manual Version 1.2 1 FOREWORD This manual is intended for sound-, lighting- and rigging technicians. The set-up
More informationAutolock Tipping Skip
User Guide Autolock Tipping Skip Introduction Conquip Autolock Tipping Skip FA800 is the choice for many sites and leading plant companies. Its primary function is for the transportation of waste material.
More informationMevaFlex Assembly and Operating Instructions
Assembly and Operating Instructions is a slab formwork which is not restricted by modular dimensions and therefore doesn't dictate to any rules of a modular system. Due to the versatility of the system,
More informationBOH FPU Systems BOH ENVIRONMENTAL LLC Avion Parkway, Suite 220 Chantilly, VA POC Jim Stokes (703)
FPU SYSTEMS OPERATION MANUAL (INCLUDING REPAIR PARTS & SPECIAL TOOL LIST) BOH QUADCON MODULES, ADAPTERS and RESTRAINT SYSTEM BOH FPU Field Pack/up Units BOH FPU Systems BOH ENVIRONMENTAL LLC 14520 Avion
More informationSafeDeck Supported Scaffold System
SafeDeck Supported Scaffold System Table of Contents Origination 1 Range of Motion 1 Installation Efficiency 2 Third-Party Testimonial 2 SafeDeck Specifications 3 Competent Person 4 Tools Required 4 Components
More informationPERI PD 8 The cost-effective shoring for slab tables and high loads
PERI PD 8 The cost-effective shoring for slab tables and high loads Edition 06/2010 PERI GmbH Formwork Scaffolding Engineering P.O. Box 1264 89259 Weissenhorn Germany Tel +49 (0)7309.950-0 Fax +49 (0)7309.951-0
More informationINDUSTRIAL CONSTRUCTION GENERAL MANUFACTURING
DtEC MATERIALS HANDLING The one stop shop for WAREHOUSE INDUSTRIAL CONSTRUCTION GENERAL MANUFACTURING email: sales@tippingskips.com www.tippingskips.com DtEC Materials Handling is a leading manufacturer
More informationSummary. Mini KKP - Assembly and operating manuel Pile guide box. Montage. Implementation. Accessories. Technical data
Summary Technical data Montage Implementation Accessories p3 p5 p6 p7 KRINGS INTERNATIONAL FRANCE - Mini KKP - 1 Conformité DIN 4124 DIN EN 13331 H L L c b C0 b CU b t pl Plate height Plate length Pipe
More informationix Stage stage platform
ix Stage stage platform user manual Musikhaus Thomann Thomann GmbH Hans-Thomann-Straße 1 96138 Burgebrach Germany Telephone: +49 (0) 9546 9223-0 E-mail: info@thomann.de Internet: www.thomann.de 26.01.2016,
More informationLesson 4: Flood Response Methods
Lesson 4: Flood Response Methods In this lesson, you will learn the advantages and disadvantages of expedient flood works. Selecting the proper flood response technique is essential to the success of the
More informationh Installation Manual
h Installation Manual 1 General Information The installation of HOBAS GRP Pipes is subject to applicable standards and guidelines such as EN 1610 and ISO/ TS 10465-1. Correct installation always requires
More informationSP Prop Steel prop. // Versatile, strong, safe
Steel prop // Versatile, strong, safe IMPORTANT: Any safety provisions as directed by the appropriate governing agencies must be observed when using our products. The pictures in this brochure are snapshots
More information8 Rung Industrial Tower
A SAFER WAY TO REACH NEW HEIGHTS 8 Rung Industrial Tower Instruction Manual Mobile Access Tower 3T - Through the trap method Introduction This Assembly Guide is intended to provide you with step-by-step
More informationSAFEEND P4 WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE. Doc. No.: SafeEnd P4 - Rev. A
SAFEEND P4 WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE Doc. No.: SafeEnd P4 - Rev. A Working Description Prepared by: Fredrik Sangö Doc. no.: SafeEnd P4 Introduction/data: SafeEnd P4 is a
More informationInstructions. Slim temporary safety barriers SB 50 Installation and Maintenance Manual. Documentation for license partners
Slim temporary safety barriers SB 50 Installation and Maintenance Manual Documentation for license partners General information 2 Planning 3 Installation 4 Special elements 7 Procedures after an impact
More informationMETALWORKS RH215 Faceted Custom Hook-on Panels
METALWORKS RH215 Faceted Custom Hook-on Panels Assembly and Installation Instructions 1. GENERAL 1.1 Product Description MetalWorks RH215 Faceted Custom Hook-on panel system is a downward accessible, custom
More informationINSTALLATION MANUAL IN-GROUND
INSTALLATION MANUAL IN-GROUND Dig holes according to positions on drawings (see the following pages). Dimensions of holes: e.g. 50 x 50 x 75 cm (see the following pages). Fill with concrete leaving a depth
More informationBirsta 3PH2b WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE. Doc. No.: Birsta 3PH2b - Rev. 0
Birsta 3PH2b WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE Doc. No.: Birsta 3PH2b - Rev. 0 Working Description Prepared by: Fredrik Sangö Doc. no.: Birsta 3PH2b Introduction/data: Birsta 3P
More informationTL-2 Plastic Water Filled Barrier
TL-2 Plastic Water Filled Barrier Product Manual ANOTHER AMORFLEX DEVELOPMENT Table of contents Introduction 3 System overview 3 Before installation 3 Limitations and warnings 4 Safety statements 4 System
More informationCivil and Structural Engineering CONSTRUCTION OF BRIDGE STRUCTURES SHALL BE IN ACCORDANCE WITH THE FOLLOWING SPECIFICATIONS, LISTED IN ORDER OF PRECEDENCE: 1. CDOT STANDARD SPECIFICATIONS FOR ROAD AND
More informationUSER S MANUAL HAKI PUBLIC ACCESS STAIR
USER S MANUAL HAKI PUBLIC ACCESS STAIR HAKI AB 2017 Important information HAKI s product liability and user s manuals apply only to scaffolds that are entirely composed of components that have been made
More informationStormTech Construction Guide
Stormtech MC-3500 Construction Guide 12/31/14 11:18 AM Page 1 M /M 00 35 C- A division of REQUIRED MATERIALS AND EQUIPMENT LIST 00 45 C- StormTech Construction Guide Detention Retention Water Quality Acceptable
More informationMDS TL5 Minimum Deflection Systems
MDS Minimum Deflection Systems Approvals FHWA NCHRP 350 MASH EN1317 H4 MDS BARRIERS Bridge & Road STEEL BARRIER SYSTEMS Page Page 1 1 V11 MDS BARRIERS Run-off-road crashes are one of the most common types
More information1450/850. Instruction Manual. Mobile Access Tower
A SAFER WAY TO REACH NEW HEIGHTS 1450/850 Instruction Manual Mobile Access Tower 3T - Through the trap method Introduction This Assembly Guide is intended to provide you with step-by-step instructions
More informationMDS TL4 Minimum Deflection Systems
MDS Approvals FHWA NCHRP 350 MASH-08 EN1317 H2 Bridge & Road STEEL BARRIER SYSTEMS Page 1 V11 Run-off-road crashes are one of the most common types of crashes in urban and highway environments. Installing
More informationAssembly and users manual. Pallet racking Alfa
Assembly and users manual Pallet racking Alfa ASSEMBLING OF FRAMES Tightening Torque Screw M0 8.8 Max. tightening torque 7 Nm Taptite M6 Max. tightening torque 5 Nm Taptite M8 Max. tightening torque 5
More informationRolling Towers. Layher Rolling Towers Uni Wide. Safety Structure Instructions for Assembly and Use. Mobile working platforms to DIN EN 1004:
Layher Rolling Towers Uni Wide Safety Structure Instructions for Assembly and Use Mobile working platforms to DIN EN 1004:2005-03 Working platform 1.5 x 2.85 m Rolling Towers max. working height: indoors
More informationSTRAIL - installation instructions. Subject to technical changes / December STRAIL level crossing systems & STRAILastic track damping systems
STRAIL - installation instructions Subject to technical changes / December 2009 STRAIL level crossing systems & STRAILastic track damping systems Gummiwerk KRAIBURG Elastik Gmbh / D-85429 Tittmoning Goellstrasse
More informationEnviroModule TM 2 installation guide
EnviroModule TM 2 installation guide assembly excavation installation backfilling design examples contents Product specifications 2 Assembly 3 Excavation 5 Installation 6 Rainwater harvesting - residential
More information" RISKS ASSOCIATED WITH THE INSTALLATION OF THE SYSTEM
PALLET RACK 85-110 installation, use and maintenance instructions Shelving made entirely of first grade certified steel sheet and cold-profiled steel with galvanized steel according to SENDZIMIR process
More informationS4 Taifun Installation Manual
CEIL ING LIGHTING AMBIENCE S4 Taifun Installation Manual GENERAL INFORMATION GENERAL INFORMATION This assembly manual addresses all metal ceilings manufactured by durlum. The different sections describe
More informationMECHANICAL LEVELERS. P.O. Box 338 Spring Hill, Tennessee /486/ /251/3382 Fax 931/486/0316
EDE & BLE Owner s Manual MECHANICAL LEVELERS P.O. Box 338 Spring Hill, Tennessee 37174 931/486/2296 800/251/3382 Fax 931/486/0316 www.pioneerleveler.com SM SECTION 1 RECEIVING: INSTALLATION INSTRUCTIONS
More informationPHYSICAL BARRIERS MACHINE GUARDS ROBOTIC WORK CELLS PERIMETER OR AREAS GUARDS PHYSICAL BARRIERS
PHYSICAL BARRIERS MACHINE GUARDS ROBOTIC WORK CELLS PERIMETER OR AREAS GUARDS PHYSICAL BARRIERS Quick-Ship Ships in 48 Hours The 6-2 Guard System Our barriers are a reliable, versatile, and economical
More informationStormTech Construction Guide
A division of StormTech solid end caps and pre-cored end caps StormTech chambers StormTech manifolds and fittings Acceptable fill materials per Table 1 Woven and non-woven geotextiles 80-7 DC REQUIRED
More informationSafety First Mobile Towers - 3T Method
USER GUIDE Edition Aug 2011 MiniMax Mobile Aluminium Trade Quality Access Tower System 3T - Through the Trapdoor Method Safety First Mobile Towers - 3T Method INTRODUCTION Please read this guide carefully.
More informationMALTE Outdoor. the compact and versatile posterior-walker. Instructions for use
MALTE Outdoor the compact and versatile posterior-walker Instructions for use Dear Customer, At this point we would like to thank you for placing your trust in our company and for purchasing our product.
More informationAssembly and Usage Instructions Z 600 S-PLUS mobile scaffold tower with stabilisers Z 600 S-PLUS folding scaffold unit COMPACT
09/2016 No. 291358 en Assembly and Usage Instructions Z 600 S-PLUS mobile scaffold tower with stabilisers Z 600 S-PLUS folding scaffold unit COMPACT 2 Contents en 1 General information... 4 1.1 Introduction...4
More informationMaterials Handling, Storage, and Disposal
Materials Handling, Storage, and Disposal Material Handling 14.A.01 - Employees shall be trained in and shall use safe lifting techniques. 14.A.03 - Material handling devices shall be available for material
More informationS7 Taifun Installation Manual
CEIL ING LIGHTING AMBIENCE S7 Taifun Installation Manual GENERAL INFORMATION GENERAL INFORMATION This assembly manual addresses all metal ceilings manufactured by durlum. The different sections describe
More informationRAPID Column Formwork For the highest requirements on concrete surfaces and edge formation. Product Brochure Issue 10/2017
For the highest requirements on concrete surfaces and edge formation Product Brochure Issue 10/2017 Content System advantages 5 For the highest requirements on concrete surfaces and edge formation 8 For
More informationLADDERSPAN AGR. BoSS Camlock Advance Guardrail Mobile Aluminium Tower 1450/850 Frames USER GUIDE
LADDERSPAN AGR BoSS Camlock Advance Guardrail Mobile Aluminium Tower 1450/850 Frames USER GUIDE Contents Safety First Safety Checklist Quantity Schedules Assembly and Dismantling Procedure Toe Boards Stabilisers
More informationImperial. folds. Wall braces are attached to the multifunction. guard-railing post. Formworkprop. connectors and flange screws.
Wall all braces / Working scaffolds folds Wall braces are attached to the multifunction profiles by formwork-prop connectors and flange screws. guard-railing post brace frame 250 consists of push-pull
More informationSafety First Mobile Towers - 3T Method
Safety First Mobile Towers - 3T Method INTRODUCTION Please read this guide carefully. Please note that diagrams are for illustrative purposes only. User guides are also available to download from our website
More informationAssembly and usage instructions REACHMASTER
Assembly and usage instructions REACHMASTER Assembly and usage instructions Assembly and usage instructions 3 Table of contents 1. General information 4 1.1. Introduction 4 1.2. Manufacturer 4 1.3. Type
More informationMAXIMO MXH Heated Formwork The cost-effective solution for concreting operations at low temperatures. Product brochure
MAXIMO MXH Heated Formwork The cost-effective solution for concreting operations at low temperatures Product brochure Product advantages MAXIMO MXH Heated Formwork The cost-effective solution for concreting
More informationTOWER EXTENSION PACK 3 Model No. SSCL3. TOWER EXTENSION PACK 4 Model No. SSCL4 INSTRUCTIONS FOR: PLATFORM SCAFFOLD STAND. Model No. SSCL1.
TOWER EXTENSION PACK 3 Model No. SSCL3 INSTRUCTIONS FOR: PLATFORM SCAFFOLD STAND Model No. SSCL1.V2 TOWER EXTENSION PACK 4 Model No. SSCL4 Thank you for purchasing a Sealey product. Manufactured to a high
More informationSYSTEM S4-RHOMBOS INSTALLATION MANUAL
SYSTEM S4-RHOMBOS INSTALLATION MANUAL GENERAL INFORMATION GENERAL INFORMATION This assembly manual addresses all metal ceilings manufactured by durlum. The different sections describe the related/relevant
More informationMiniMax USER GUIDE. Mobile Aluminium Trade Quality Access Tower System. 3T - Through The Trapdoor Method
MiniMax Mobile Aluminium Trade Quality Access Tower System 3T - Through The Trapdoor Method USER GUIDE Contents Safety First Component Diagram Component Quantity & Safety Data Schedule Build Method Pre-use
More informationInstallation Guide. PrivacyShield Outdoor Enclosure
Installation Guide PrivacyShield Outdoor Enclosure Table of Contents 1.0 Introduction... 2 2.0 Materials, Delivery & Tools... 2 3.0 Layout and Post Locations. 3 4.0 Foundations... 5 5.0 PVC Installation....
More informationmandarin imports & exports
mandarin imports & exports Forklift Attachments Catalogue Tyne Extension Slippers P1 SPECIALISING IN CUSTOM MADE & DESIGN Container ramps P2-3 Safety cages/work platforms P4 Goods Cage P5-6 Jibs P7-15
More informationFormwork Direct International. Tel: Heavy Duty Panel System
Formwork Direct International Tel: 0151 532 0179 sales@formworkdirect.co.uk www.formworkdirect.co.uk Heavy Duty Panel System Product Overview The FD Max panel is a heavy duty wall formwork system capable
More informationSpaceInvader pallet rack Manual. Scan QR code or go to to view a practical video introduction
SpaceInvader pallet rack Manual Scan QR code or go to www.spaceinvader.com/video to view a practical video introduction Product description Technical tool consisting of two identical racks, which combined
More informationHeavy-Duty Braces Triplex Assembly and Operating Instructions
Heavy-Duty Braces Triplex Assembly and Operating Instructions Product features and use How to read this manual Triplex is a heavy duty brace (three chords) to align and brace formwork with heights exceeding
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS Multifunction Rolling Scaffold Towers 6, 12 and 18 READ ALL INSTRUCTIONS AND WARNINGS BEFORE USING THIS PRODUCT. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. This manual provides
More informationASSEMBLY INSTRUCTION ROLLING TOWER RT 1400 & RT 1400XR ROLLING TOWER RT 750 & RT 750XR STAIR TOWER ST 1400 FOLDABLE TOWER FT 750 & FT 750XR
ASSEMBLY INSTRUCTION ROLLING TOWER RT 1400 & RT 1400XR ROLLING TOWER RT 750 & RT 750XR STAIR TOWER ST 1400 FOLDABLE TOWER FT 750 & FT 750XR EN 1298 - IM - en SC1809 12 SAFETY IN EVERY STEP wibeladders.com
More informationCONNECTOR S T U D S H E A R. Design for Composite Structural Action STUD SHEAR CONNECTOR APPLICATION
S T U D S H E A R CONNECTOR STUD SHEAR CONNECTOR APPLICATION Design for Composite Structural Action Exterior ashlar-type masonry veneer, typically of clay brick or concrete block masonry, are commonly
More informationSYSTEM S7-RHOMBOS INSTALLATION MANUAL
SYSTEM S7-RHOMBOS INSTALLATION MANUAL GENERAL INFORMATION GENERAL INFORMATION This assembly manual addresses all metal ceilings manufactured by durlum. The different sections describe the related/relevant
More informationPACIFIC SHORING, LLC ALUMINUM SHORING PRODUCTS ALUMINUM S-PANEL SHIELDS. TABULATED DATA Effective April 01, 2014
1 ALUMINUM S-PANEL SHIELDS Effective April 01, 2014 PSH 265 Roberts Avenue Santa Rosa, Ca. 95407 (707) 575-9014 Construction Engineering Resource 1837 Wright Street Santa Rosa, Ca. 95404 jmtengr2@aol.com
More informationStormTech Construction Guide
M /M 00 35 C- A division of REQUIRED MATERIALS AND EQUIPMENT LIST 00 45 C- StormTech Construction Guide Detention Retention Water Quality Acceptable fill materials per Table 1 Woven and non-woven geotextiles
More informationHydraulic Excavators
Chapter 8 Hydraulic Excavators Hydraulic excavators are designed to excavate below the ground surface on which the machine rests. These machines have good mobility and are excellent for general-purpose
More informationLEADING IN WELDING SAFETY CATALOGUE 2014 CONSTRUCTION. Version 14/01
LEADING IN WELDING SAFETY CATALOGUE 2014 CONSTRUCTION Version 14/01 CONSTRUCTION Table of contents TABLE OF CONTENTS General information 3 Quality 4 Swivel arms 5 Swivel arms supports 16 Poles 18 Columns
More informationMOBILE ACCESS TOWER INSTRUCTION MANUAL SHALLOW BRACE. Incorporating the 3T method of assembly
MOBILE ACCESS TOWER Incorporating the 3T method of assembly SHALLOW BRACE INSTRUCTION MANUAL 2 INTRODUCTION This instruction manual contains all the information required to correctly assemble the OCTO
More informationOperator Manual JCB Q-Fit to Sanderson Adapter
1 Operator Manual JCB Q-Fit to Sanderson Adapter Main Street Garton-on-the-Wolds Driffield, YO25 3ET Tel: 01377 259140 Email: sales@agriweld.co.uk www.agriweld.co.uk 2 Contents Page 3 Assembly Page 4 Part
More informationSAFETY SYSTEM. G-Deck Consideration. Manual Handling
INTRODUCTION The G-Deck load deck system is a high strength, low cost access platform which is quick to erect, durable and flexible enough to meet your site access needs. Safety is a priority and G-Deck
More informationSAFE ERECTION AND USE OF ALUMINIUM TOWERS/SCAFFOLDS
SAFE ERECTION AND USE OF ALUMINIUM TOWERS/SCAFFOLDS PERSONNEL DIVISION Revised 2002 CONTENTS Page 1 INTRODUCTION 1 2 APPLICATION 1 3 ERECTION AND INSPECTION 1 4 ERECTION 1 4.1 Before erection of tower
More informationUser Manual Agreto Heavy Duty Modules 5t/10t/15t
User Manual Agreto Heavy Duty Modules 5t/10t/15t 21.6.2017 Content 1 Introduction... 3 2 Scope of delivery... 3 3 Intended use... 3 4 Security... 4 5 Technical Specifications... 5 6 Mounting the Agreto
More informationConergy SolarFamulus II
Conergy SolarFamulus II Installation manual www.conergy.com Table of Contents Table of Contents SolarFamulus II for universal use on flat roofs 1 Introduction 1 1.1 Short description 1 1.2 Intended use
More informationPipes, Piles, and Accessories
Pipes, Piles, and Accessories ON-SITE RECOMMENDATIONS FOR SAFE HANDLING Contents: 1. General 2. Reception of products and inspection 3. Unloading and moving 4. Storage 5. Handling of coated pipes 6. Installation
More informationA SAFER WAY TO REACH NEW HEIGHTS. Instruction Manual. Mobile Access Tower. 3T - Through the trap method
A SAFER WAY TO REACH NEW HEIGHTS UTS1450/850 Instruction Manual Mobile Access Tower 3T - Through the trap method Introduction This Assembly Guide is intended to provide you with step-by-step instructions
More informationSafety Ladders: Made of Aluminium
Y-Spar Anodized aluminium alloy ladder. Guide-rail profile: 52 x 51 mm. Comes with joint plate. Mounting brackets extra to order. Mounting distance: recommended 1400 mm - max. 1680 mm. Installation of
More informationCUSTERS FOLDY MOBILE SCAFFOLDING
INSTRUCTION MANUAL CUSTERS FOLDY MOBILE SCAFFOLDING Maximum payload: 150 kg/m 2 (2 persons plus equipment) 9505.770.001EN sept 2016 CUSTERS HYDRAULICA B.V. Smakterweg 33 5804 AE VENRAY NL Tel. : +31 (0)
More informationHigh Performance. Cost Effective. Easy Installation.
High Performance Cost Effective Easy Installation 1 www.highwaycareint.com Testing & Approval BarrierGuard 800 has been tested to meet the highest performance standards in the world, passing both the American
More informationPROLYTE ST-TOWER MANUAL ASSEMBLY INSTRUCTIONS
Make sure to read and fully understand this manual, and its specific notes and warnings, prior to assembly and erection of the structure. PROLYTE ST-TOWER MANUAL ASSEMBLY INSTRUCTIONS Contents: 1 System
More informationS-60-TO : 1 ton tower system
S-60-TO : 1 ton tower system INSTRUCTION MANUAL ALC Truss S-60-TO Tower Manual Version 1.4 1 FOREWORD This manual is intended for sound-, lighting- and rigging technicians. The set-up and operation of
More informationSTRAIL level crossing systems & STRAILastic track damping systems
pontistrail - installation instructions Subject to technical changes / February 2010 STRAIL level crossing systems & STRAILastic track damping systems Gummiwerk KRAIBURG Elastik GmbH / D-84529 Tittmoning
More informationOperator Training Program. PROSTAK Storage Management Systems
Operator Training Program PROSTAK Storage Management Systems Operator Training Index 1. PROSTAK System Nomenclature Slide 3 2. Safe Operating Guidelines Slides 4 and 5 3. Types of PROSTAK Stackers Slide
More informationInstallation and Operating Instructions Interroll Roller Conveyors Ball Table RM 8130 Omni Wheel Table RM 8140 non-powered
Installation and Operating Instructions Interroll Roller Conveyors Ball Table RM 830 Omni Wheel Table RM 840 non-powered Version. (0/206) en-us Manufacturer's address Interroll Automation GmbH Dietmar-Hopp-Straße
More informationSectional Scaffold. Scaffold Access Unit Installation Instructions
Sectional Scaffold Scaffold Access Unit Installation Instructions 2 Scaffold Access Unit Installation Instructions SAU6 Painted: 18.3 lb Galvanized: 20.2 lb Label 7112A0003 NOTICE Please read and follow
More informationCONNECTOR B L O C K S H E A R. Design for Composite Structural Action BLOCK SHEAR CONNECTOR APPLICATION. Airspace
B L O C K S H E A R CONNECTOR BLOCK SHEAR CONNECTOR APPLICATION Airspace Design for Composite Structural Action Exterior ashlar-type masonry veneer, typically of clay brick or concrete block masonry, are
More informationMGF TECHNICAL FILE ALUMINIUM UTILITY MANHOLE BRACE. Description. Product Notes.
Description Simple to assemble, four sided, aluminium hydraulic bracing frame system, designed to be used with steel trench sheets to brace small, shallow cofferdams for the safe installation of manholes
More informationMiller Collective Safety at Height Solutions EPIC ULTRA Barrier System EPIC Post-N-Barrier System EPIC Basic Barrier System
For over 65 years the Miller brand has been synonymous with personal fall protection products and services. As the global leader in safety at height solutions, Honeywell Safety Products introduces a new
More information