GIBERTINI OP150S. User manual. Installation Guide GIBERTINI. Supporto AZ/EL per parabole Ø 150 mm AZ/EL support for satellite dishes of Ø 150 mm
|
- Dwain McDaniel
- 3 months ago
- Views:
Transcription
1 Supporto AZ/EL per parabole Ø 150 mm AZ/EL support for satellite dishes of Ø 150 mm art SUPP. AZ/EL G TECHNICAL SPECIFICATIONS OP150S Frequency range (GHz) Feed illumination angle 70 Outside dimension (cm) x Feeder clamp (mm) 40 / 23 Reflecting dimension (cm) x Elevation angle Illumination efficiency * (%) 70 Gain GHz (dbi) Mast clamp (mm) Gain GHz (dbi) Alu reflector thickness (mm) 2.0 Gain GHz (dbi) Steel reflector thickness (mm) not available Cross polarization * on axis (dbc) - 28 alu 23,8 Antenna net weight (kg.) First side lobe level * (dbc) - 25 steel n. a. Noise temp. 12GHz, 36 elevation (K) 31 Wind 120 km/h (kg) [worst-case] 250 F/D radio 0.66 Working temperature - 30 / dB Beam 11.7GHz 1.07 Humidity 0 100% Offset pointing angle 21.3 WARNINGS We strongly encourage you to read this manual before installation and use of the product and strictly observe the recommendation hereof. v OP150S satellite offset antenna Ø 150cm Installation Guide - The producer pag. 1
2 CONTENTS OF THE PACKAGE n 1 RL150A n 1 SCC150 Reflector Refector support n 1 SPL125 n 1 SCL125 n 1 SB125 n 1 SD125-HR Pole Clamp components Elevation bracket pag. 2
3 CONTENTS OF THE PACKAGE n 1 SIN-150 n 1 SSCPAP n 1 TRL150FC n 1 TRL150FL n 1 SA150F Arms and Feed Holder mount components BERTINI n 2 TTL150 Side rods pag. 3
4 CONTENTS OF THE PACKAGE Elements and thread parts 1 for Pole mount clamp w Elements and thread parts for the Elevation bracket and reflettor support n 2 M8x20 - ISO UNI DIN933 n 4 Ø6 - ISO UNI DIN125A n 6 M8 - ISO UNI 5587 n 4 Ø8 - ISO UNI DIN125A n 6 Ø8 - DIN 6798A - UNI8842A n 4 M6x45 - ISO UNI DIN933 n 6 Ø8 - ISO UNI DIN125A n 4 M8x20 - ISO UNI DIN933 n 2 M8 - [VTM8380I] 3 Elements and thread parts for Elevation adjuster 4 Elements and thread parts for Bracket and pole mount unit assembly n 2 M8 - ISO UNI 5587 n 3 M8 - ISO UNI 5587 n 2 Ø8 - DIN 6798A - UNI8842A n 3 Ø8 - DIN 6798A - UNI8842A n 1 M8x40 - ISO UNI 5739 n 2 Ø8 - ISO UNI DIN125A n 1 L=20 - [YVD20G] n 1 [VHIPID] n 1 L=175 - [VPO175I-PR] n 3 M8x170 - ISO UNI DIN931 n 1 [SB120] n 1 [VB140] TINI pag. 4
5 CONTENTS OF THE PACKAGE 5 Elements and thread parts for Arms and feed holder mount 6 Elements and thread parts for Antenna reflector n 5 M6 - ISO UNI DIN934 n 6 M6 - ISO DIN UNI7474 n 5 Ø6 - DIN 6798A - UNI8842A n 6 M6x12 - ISO4762 n 5 Ø6 - ISO UNI DIN125A n 1 M6x45 - ISO UNI DIN933 n 2 M6x50 - ISO UNI DIN933 n 2 M6x70 - ISO UNI DIN933 n 1 CHBR4 7 Elements and thread parts for Antenna reflector n 1 M6 - ISO UNI DIN934 n 1 Ø6 - DIN 6798A - UNI8842A n 1 Ø6 - ISO UNI DIN125A n 1 M6x45 - ISO UNI DIN933 n 2 M6 - ISO DIN UNI7474 n 2 M6x12 - ISO4762 ERTINI pag. 5
6 ASSEMBLING STEPS 1 Assembly of the pole clamp mount - 2 Assembly of the Elevation bracket to the reflector support 3 Assembly of the Elevation fine regulation threaded tie-rod
7 ASSEMBLING STEPS 4 Assembly of the antenna rear bracket to the pole clamp mount 5 Assembly of arms and feed holder assy - - OK NO -
8 ASSEMBLING STEPS y Assembly of the antenna reflector on the bracket assy. BERTINI
9 ASSEMBLING STEPS u Assembly of side rods IBERTINI
10 Installation All GIBERTINI the dishes Antennas are manufactured are manufactured using using well certified well certified materials and and assembly components that ensure a a reliable and and long long life product. life product. During installation, for proper use and safety, screws and bolts have to be used in proper indicated place without exchange in position (e.g. do not use a M4 bolt where an M6 is foreseen). The personnel in charge of installation will be the sole responsible of the pole fixation on roof or wall, and have to take care of the proper tightening between antenna components. If not elsewhere indicated, the following table report the recommended tightening torque, in Newton * meter, to be applied on different mechanical couplings. Thread size Tightening Torque Bolt/Nut assembly Tightening Torque Bolt/Insert assembly pitch min [Nm] max [Nm] min [Nm] max [Nm] M M M M M M Maintenance Plan All GIBERTINI the dishes Antennas have shown have shown good good durability durability even even in worst in worst conditions, provided than that no no permanent demages damages to plating or painting have been procured during the installation or due to to other origins after installation. Nevertheless, a periodic maintenance enforce the warranty validity and help in order to elongate the life of the assembly. Period General care Paint Zinc plating Every two years or in case of storm wind and/or strong hailstorm Verify the integrity of the antenna assembly. Clean with a conventional duster the dish surface and the LNB feed -do not use solvents for normal cleaning- dry cleaning is normally enough, use water or alcohol to remove solid attached elements, dry with a cloth. If the painting has been ruined, remove gently the rust, if present, using a fine abrasive paper (type 00), then clean with acetone, chloroform or similar oil free solvent, dry and than repaint with two pass of -water based- opaque paint of the proper RAL. (Conventional paint used in car repair. Please refer to the paint Manufacturer recommendations for the latency time between the painting). Chemical solvents are flammable and volatile : do not expose directly, protect with mask and gloves. Use only opaque paints. Brilliant paints can over heat the LNB cooking it with permanent damages. If damaged due to environmental corrosion, zinc plating can be restored with a chemical zinc spray (ZINK TK0105 by TEKNICA -Italy- or similar products from other Manufacturers like TALKEN, etc.). Using a metallic brush remove oxidation and rust if present, clean with acetone, chloroform or similar oil free solvent and live it to dry. Apply one or two pass of spray zinc, having care to cover uniformly all the exposed surfaces (this apply specifically the clamp brackets). Carefully follow the indications of the spray zinc Manufacturer. The spray contain Toluene: flammable, do not expose to fire, do not smoke, do not dry with direct flame or hot air irons at temperature higher than 80 C. Vapors can cause irritation and narcotic effects, protect with mask and gloves.
Fitting and Operating Instructions
ISO 9001:2008 Cert.-No. 01 100 89747 ISO 14001:2004 Cert.-No. 01 104 069609 Metall- und Plastikverarbeitungs- GmbH & Co. KG Kierspe Internet: www.mpk-kierspe.de Fitting and Operating Instructions GB Rooflight
MOUNTING SYSTEM FOR PITCHED ROOF WITH TILES. mounting system for pitched roof with tiles for solar panels in landscape setup. Rev
MANUAL EN MOUNTING SYSTEM FOR PITCHED ROOF WITH TILES mounting system for pitched roof with tiles for solar panels in landscape setup ESDEC BV 2016 TABLE OF CONTENT 1. Introduction 1 2. General installation
ASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS for the vehicle barrier system KREMSBARRIER 2 RH2B for pile-drivable subgrades Performance class in accordance with EN 1317-2: Containment level: Impact severity level: Working width:
INSTALLATION MANUAL. METAL INSULATED PANELS -ROXUL -Expanded Polystyrene
INSTALLATION MANUAL METAL INSULATED PANELS -ROXUL -Expanded Polystyrene Insulated Metal Panels London Eco-Metal Manufacturing Inc. **Also see Eco-Metal s Handling Manual** These instructions are provided
Coating Specifications
Quadax Series Butterfly Valves Version May 2011 müller co-ax ag Gottfried-Müller-Str. 1 74670 Forchtenberg Germany Tel. +49 7947 828-0 Fax +49 7947 828-11 E-Mail info@co-ax.com Internet www.co-ax.com Table
DIN 3015 CLAMPS B1-1 PN# / / ACC
DIN 0 CLAMPS DIN 0 Clamps HYDAC manufactures a complete line of hose, tube, and pipe mounting components according to the DIN 0 standard. HYDAC clamps assure a simple, reliable dampening support for lines
2-Finger-Parallel-Gripper RH
Translation of the original manual 2-Finger-Parallel-Gripper RH 901-940 Assembly and Operating Manual Superior Clamping and Gripping Imprint Imprint Copyright: This manual remains the copyrighted property
Fitting and Operating Instructions
ISO 9001:2008 Cert.-No. 01 100 89747 ISO 14001:2004 Cert.-No. 01 104 069609 Metall- und Plastikverarbeitungs- GmbH & Co. KG Kierspe Internet: www.mpk-kierspe.de Fitting and Operating Instructions D Rooflight
ITEM 686 TRAFFIC SIGNAL POLE ASSEMBLIES (STEEL)
ITEM 686 TRAFFIC SIGNAL POLE ASSEMBLIES (STEEL) 686.1. Description. This Item shall govern for designing, fabricating, furnishing and erecting steel traffic signal pole assemblies of the various types
ASSEMBLY AND OPERATING MANUAL LTW SHORING BOXES VB 100
Dealer: MV Trench Support Ltd Letham Road Houston Industrial Estate Livingston EH54 5BY Phone: +44 (0) 1506 / 445800 Fax: +44 (0) 1506 / 443080 Mobile: +44 (0) 7917 / 208767 MV Trench Support Ltd * Letham
Sub-construction for Wall-mounted Longlight
modular skylights Sub-construction for Wall-mounted Longlight Subconstruction for Wall-mounted Longlight at 5-40 pitch modular skylights in a wall-mounted longlight solution, can be installed on a sub-construction
FEATURES APPLICATIONS. Technical data sheet SSW - STEEL STRONG-WALL FOR TIMBER FRAME RACKING RESISTANCE.
The Steel Strong-Wall is a corrugated steel panel which is designed to be fixed directly to the concrete foundations of a building, within the external or internal wall, via a bolted connection. FEATURES
Materials Carbon Steel is used in the manufacturing of riser and pipe clamps. Stainless Steel and other materials are available.
Pipe clamps offered in this section are designed for support and attachment of pipe to structural members. wide range of pipe clamps are available for various applications. Materials arbon Steel is used
PITCHED ROOF. Photovoltaic Mounting Systems. Assembly Instructions. for roofing tiles, plain tiles and slate
Photovoltaic Mounting Systems Assembly Instructions PITCHED ROOF for roofing tiles, plain tiles and slate S:FLEX GmbH 09/2017 / design and engineering is subject to change 1 Index 1 Introduction 1.1 Intended
Troubleshooting Guide 9702 Series
Troubleshooting Guide 9702 Series Satellite Solutions for Mobile Markets 11200 Hampshire Avenue South, Bloomington, MN 55438-2453 Phone: (800) 982-9920 Fax: (952) 922-8424 www.kingcontrols.com 1305-AUTO
Preparation and Installation of the FA, FAV, and FAS Type Rupture Discs in Forward Acting Insert, Full Bolted, and Union Type Holders
GEP-6050 Rev. F 23777 Ref. I.D.: 8681 Preparation and Installation of the FA, FAV, and FAS Type Rupture Discs in Forward Acting Insert, Full Bolted, and Union Type Holders WARNING USER SHOULD READ AND
Concrete screw BSZ Steel/steel zinc flake coated
Concrete screw BSZ Steel/steel zinc flake coated Concrete screw BSZ-SU Concrete screw BSZ-SUH Concrete screw BSZ-SK Concrete screw BSZ-K Concrete screw BSZ-GK Approvals and Certificates Concrete screw
PE45 AMAZON MONKEY BARS OWNER'S MANUAL
PE45 AMAZON MONKEY BARS OWNER'S MANUAL WARNING! The disassembled product may contain small parts which pose a choking hazard to children under 3. IMPORTANT: This product may contain sharp points and small
Fig Beam Clamp Retaining Strap (B-Line B3367)
Fig. 69 - Beam Clamp Retaining Strap (B-Line B3367) Size Range: 3 /8"-16 thru 3 /4"-10 rod 4 (101.6mm) thru 16 (406.4mm) lengths Note: longer lengths are available consult factory Material: Pre-Galvanized
Gyptone edge D1 system Installation manual
Installation manual Design and technique Product description Gyptone edge D is a pre-painted, demountable suspended acoustic ceiling, mounted in a concealed grid system (T-). Gyptone ceilings can be used
Technical Specification for LV ABC Fuse Switch Disconnectors
Ergon Energy Corporation Limited Technical Specification for LV ABC Fuse ETS-06-02-02 Check this is the latest Process Zone version before use. Specification ETS 06-02-02 Ver 3 Contents 1. Purpose and
Raised Basement. Mechanical Installation Guide
R Raised Basement Mechanical Installation Guide Ensure masonry work is correct. If recessed, the depth must be 14 inches deep unless otherwise specified for a custom application. Width and length may vary
Huck Seiltechnik GmbH Aßlar/Berghausen Germany
Seiltechnik GmbH 35614 Aßlar/Berghausen Germany A Assembly Instructions Arch Swing with Buried Ground Anchors Art-No. 4580-4B Operator: Location: T:\PLAY\Play Installation Instructions\Word Document Install
Sprinkler Identification Numbers (SINs)
Worldwide Contacts www.tyco-fire.com Model 2.8 K-factor Combustible Concealed Space Sprinklers Specific Application, Upright General Description The Model Combustible Concealed Sprinklers are fast response,
2-finger angular gripper SGB 32-50
www.comoso.com Translation of the original manual 2-finger angular gripper SGB 32-50 Assembly and Operating Manual Superior Clamping and Gripping Imprint www.comoso.com Imprint Copyright: This manual remains
0500/12.02 SEAL LOCK. Sealing nuts with reduced installation effort and prevention against loss
0500/12.02 SEAL LOCK Sealing nuts with reduced installation effort and prevention against loss The reliable solution for sealing bolt-nut joints Screwed connections remain in very common use. In many cases,
DURA-BLOK is made from 100% recycled rubber and qualifies for LEED credits. Reflective strips on both sides allow for easy product visibility.
is made from 100% recycled rubber and qualifies for LEED credits. Reflective strips on both sides allow for easy product visibility. Channels are through bolted on all sizes for added strength and a 1
ELECTRONIC EARTHING EQUIPMENT SERIES GRD 4200
ELECTRONIC EARTHING EQUIPMENT SERIES GRD 4200 The GRD 4200 is an electronic earthing equipment for tankers during loading and unloading operations of flammable liquids in places with danger of explosion.
Z5378 E6 Horizontal bracket Mounting instructions (1.0 EN)
Z5378 E6 Horizontal bracket Mounting instructions (1.0 EN) Contents 1. Product description and scope of supply...3 2. Intended use...4 3. Safety precautions...4 4. Assembly...4 5. Maintenance and care...5
Z5033 E3 Ball joint adapter Mounting instructions
Z5033 E3 Ball joint adapter Mounting instructions Z5033 E3 Ball joint adapter References in the manual This refers to a potentially dangerous situation which may lead to personal injury. This refers to
built build to FORMWORKS CLIMBING, RETAINING WALLS, SPECIAL
uilt build to FORMWORKS Company Projects Products CLIMBING SYSTEMS Pilosio s CLIMBING SYSTEM with mechanical handling enable vertical construction joints to be created in succession without the aid of
Jet Tunnel Fans.
Jet Tunnel Fans www.systemair.de by Division AJ (T) Tunnel Jet Fans Standard features: Thrust efficiency in excess of 40 N/kW Adjustable aluminium impellers for maximum efficiency Terminal box on the casing
Table of Contents. List of Drawings
SCOPE OF WORK Hastings Stadium Exhibition Park, 81 London Road, Guelph, Ontario Structural and Maintenance Remedial Work Prepared For City of Guelph City Hall, 1 Carden Street, Guelph, ON N1H 3A1 Prepared
Installation manual ValkTriple EN-UK
Van der Valk Solar Systems TRCKING ND FIXED SOLR MOUNTING SYSTEMS Installation manual ValkTriple EN-UK Version 08 EN General user instructions Solar mounting systems Congratulations on buying a Van der
1-part polyurethane pourable self levelling floor joint sealant
Product Data Sheet Edition 29/03/2007 Identification no: 02 05 01 01 018 0 000001 1-part polyurethane pourable self levelling floor joint sealant Construction Product Description Uses Characteristics /
E-Series Steel Gantry Crane
SPANCO PRODUCT SPECIFICATIONS 1 E-Series Steel Gantry Crane This guide can be used to prepare a bid specification for the incorporation of an E-Series Gantry Crane into a competitive bid project or application.
Design and Analysis of Antenna Reflector Using Composite Materials
Design and Analysis of Antenna Reflector Using Composite Materials Mithunkumar C.N, Venkateshmurthy Mechanical department, NMAMIT, Nitte, India. Abstract: An Antenna is basically a dish-shaped device of
Better by being quick to translate market trends into products. In this way, our innovative strength helps you to secure competitive advantages.
02 Stainless Steel Rittal The System. The whole is more than the sum of its parts. The same is true of Rittal The System. With this in mind, we have bundled our innovative enclosure, power distribution,
Z5043 MAX Horizontal bracket Mounting instructions
Z5043 MAX Horizontal bracket Mounting instructions Z5043 MAX Horizontal bracket References in the manual This refers to a potentially dangerous situation which may lead to personal injury. This refers
TRANSPORT II " 10.5" MOUNTING POSTS FENCE LINE POST. Classic gate shown GATE OPENING CANTILEVER GATE SAFETY WARNING
TRANSPORT ESTATE TRANSPORT IS TRANSPORT LINK ADAPTRACK 2"sq x.25" UPRIGHTS & DIAGONAL BRACES 1"sq x.125" PICKETS GATE TRACKS PRE-DRILLED FOR LEFT OR RIGHT OPENINGS FENCE LINE POST 13.8125" 10.5" MOUNTING
Thermal Diffusion Galvanizing
Engineering Test Report M-571 Thermal Diffusion Galvanizing For Pole Line Hardware Revision D 11.17.2017 Added further Corrosion Test results and Abrasion Test results Prepared by 1. Introduction to Thermal
Z5377 E6 Swivel bracket Mounting instructions (1.2 EN)
Z5377 E6 Swivel bracket Mounting instructions (1.2 EN) Contents 1. Product description and scope of supply...3 2. Intended use...3 3. Safety precautions...4 4. Assembly...4 5. Operation...4 6. Maintenance
5230VS Series. Chevron Long Edge Milling Cutter (Porcupine)
5230VS Series Chevron Long Edge Milling (Porcupine) Shoulder / Profiling / Slotting HIGH PERFORMANCE LONG EDGE MILLING CUTTERS The Stellram 5230VS09 and VS12 Series is perfectly quali ed for pro ling and
Installation Instructions
Installation Instructions Dynarail Safety Ladder System Corrosion Resistant Nonconductive Fire Retardant High Strength-To-Weight Ratio Long, Low Maintenance Life Meets OSHA, BOCA & Other Building Code
The Perfect Building Integrated PV Solution Simple Beautiful Efficient
Solar Innovative technology with an optimum of efficiency and a perfect appearance The Perfect Building Integrated PV Solution Simple Beautiful Efficient Energaia Innovation Trophy 2008 Winner (best innovation
Triangolo. Small Triangolo. Large Triangolo. Small Triangolo Fresnel lens. Large Triangolo. Fresnel lens. Small Triangolo Diamond lens
Triangolo Small Triangolo Registered patent Large Triangolo Small Triangolo Large Triangolo Small Triangolo Diamond lens 1987: Triangolo takes the market. Since that time Triangolo is the original and
Installation and operating manual for DIN , DIN , DIN EN ISO FIXED VERTICAL LADDERS
Installation and operating manual for DIN 18799-1, DIN 14094-1, DIN EN ISO 14122-4 FIXED VERTICAL LADDERS Introduction Dear Customer, with the purchase of the fixed ladder system you have chosen a quality
Three-sided barrier compliant to DIN EN ISO Depending on location, design also as wind protection. Clear height (DH) Three-sided barrier
of 5 Page Car SingleVario 06 Stack Parker 06 50 for vehicle up to 5.00 m = 6 long (50 for vehicle up to 5.0 m 7 long) Depending on location, design also as wind protection. Product Data CONFORMITY 06/06/G63
ALUBOX Series Junction boxes in IP66 aluminium alloy
UBOX Series Junction boxes in IP aluminium alloy > ENCLOSURES IP UBOX Series UBOX-EX Series Dimensions () Screw for attaching cover Earthing screws Weight (Kg) 00 x 00 x 59 n 2 M5x0 n M4x 0,290 /32 53.00
W TEC SURFACE PROTECTION
WÜRTH Industrie Service DE EN W TEC SURFACE PROTECTION Optimum corrosion protection for your C-Parts CHROMIUM(VI)-FREE REACH COMPLIANT Table of contents Page Preface 1 Ban of chromium(vi) 2 Würth Surface
PERI PD 8 The cost-effective shoring for slab tables and high loads
PERI PD 8 The cost-effective shoring for slab tables and high loads Edition 06/2010 PERI GmbH Formwork Scaffolding Engineering P.O. Box 1264 89259 Weissenhorn Germany Tel +49 (0)7309.950-0 Fax +49 (0)7309.951-0
European Technical Assessment ETA-10/0422 of 08/01/2016
ETA-Danmark A/S Göteborg Plads 1 DK-2150 Nordhavn Tel. +45 72 24 59 00 Fax +45 72 24 59 04 Internet www.etadanmark.dk Authorised and notified according to Article 29 of the Regulation (EU) No 305/2011
Tandem subtly articulates the entry to the building. We were very pleased with the result.
Tandem subtly articulates the entry to the building. We were very pleased with the result. RACHEL PETRO RNL Lighting designer TANDEM National Renewable Energy Labs Golden, Colorado Architeture by RNL 24
SYSTEM S7-RHOMBOS INSTALLATION MANUAL
SYSTEM S7-RHOMBOS INSTALLATION MANUAL GENERAL INFORMATION GENERAL INFORMATION This assembly manual addresses all metal ceilings manufactured by durlum. The different sections describe the related/relevant
SECTION SECTIONAL OVERHEAD DOORS
SECTION 08360 SECTIONAL OVERHEAD DOORS PART 1 GENERAL 1.1 SECTION INCLUDES A. Aluminum Doors B. Track and Framing 1.2 RELATED SECTIONS A. Section 04810 - Unit Masonry Assemblies: Prepared opening in masonry.
Installation plan. Tumble dryer. PT 8807 EL (Electrically heated) en - US Mat. NR / 02
Installation plan Tumble dryer PT 8807 EL (Electrically heated) 38.15 en - US Mat. NR. 09 883 210 / 02 U.S.A. Miele, Inc. National Headquarters 9 Independence Way Princeton, NJ 08540 Phone: Fax: 800-991-9380
Fig. 1 - Standard Clevis Hanger
Revision 10/24/2007 Fig. 1 - Standard Clevis Hanger Component of State of California OSHPD Approved Seismic Restraints System Size Range Size 1/2" thru 36" pipe. Function Recommended for the suspension
Presentation of prefabricated houses. - Main equipments. - Assembly steps. - Some realisations
Prefabricated Houses Presentation of prefabricated houses - Employed components - Main equipments - Assembly steps - Some realisations SKA spa via Agosta, 3-36066 Sandrigo (VI) - Italy - Tel. + 39 0444
REPORT HOLDER: FASTENING SPECIALISTS, INC. 726 CENTRAL FLORIDA PARKWAY ORLANDO, FLORIDA EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Evaluation Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2328 Reissued 10/2017 This report is subject to renewal 10/2018. DIVISION: 03 00
A. This Section includes acoustical panel ceilings installed with exposed suspension systems.
SECTION 09511 ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
MALTE Outdoor. the compact and versatile posterior-walker. Instructions for use
MALTE Outdoor the compact and versatile posterior-walker Instructions for use Dear Customer, At this point we would like to thank you for placing your trust in our company and for purchasing our product.
ValkPitched - Insert
ValkPitched - Insert Installation manual Use in combination with the Project Report of the ValkPVplanner Version 14 EN Van der Valk Solar Systems Solar Mounting Systems Please Note Table of contents This
Superstrut. Metal Framing. Pipe Straps, Pipe Clamps and Hangers
Design Loads Where design loads are indicated, they provide for a safety factor of 3 in conformance with the American Standard Code for Pressure Piping. Hanger Design Pipe hangers are of advanced design
FASTENERS FOR THE AGRICULTURAL INDUSTRY
FASTENERS FOR THE AGRICULTURAL INDUSTRY 2 Fully-automated warehouse logistics About REYHER Today, with 130 years experience REYHER is one of the leading trading companies for fasteners and fixing technology
1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases.
SECTION 260529 - HANGERS AND SUPPORTS PART 1 - GENERAL 1.1 SUMMARY A. Section includes: 1. Hangers and supports for electrical equipment and systems. 2. Construction requirements for concrete bases. 1.2
ETALLODOMI S.A. Head Office: 12, Kastorias str Athens GREECE. Main Warehouse: 49, Agiou Orous str. GREECE
About the company... METALLODOMI S.A. was founded in 1995 and since then is experiencing a constant growth. The company operates primarily in steel sheet processing sector and in particular the production
2. Cab, interior finishes, control panel and facings including cab doors. 3. Fire rated hoistway doors, sills, and frames.
PART 1: GENERAL 1.01 Summary Section Includes: 1. Electric traction Dumbwaiter system. 2. Cab, interior finishes, control panel and facings including cab doors. 3. Fire rated hoistway doors, sills, and
VAN RACKING SYSTEMS.
VAN RACKING SYSTEMS www.baggioedesordi.com VAN RACKING SYSTEMS We organize the space of each van and improving its capacity. Our objective? Making the interior equipment rational and safe. Upright > Material:
DUGOUT MODEL (4 POST) 10 x 24 SPECIFICATIONS
DUGOUT MODEL (4 POST) 10 x 24 SPECIFICATIONS Dimensions: Roof Dimensions 10-0 x 24 Column Dimensions (center to center) 6-7 x 22-9 Minimum Clearance 7-6 Minimum Clearance @ Front ±9-2 Roof Pitch 2:12 pitch
QUICK-LOCK QUICK-LOCK. A complete survey of all Quick-Lock ceiling systems. QUICK-LOCK Ceiling systems. QUICK-LOCK Cross-Lock.
A complete survey of all Quick-Lock ceiling systems QUICK-LOCK Ceiling systems QUICK-LOCK Cross-Lock QUICK-LOCK Omega QUICK-LOCK Insula QUICK-LOCK The best base for your ceiling. Unique systems The Quick-Lock
AKS Coatings GmbH. A new Generation of protective surface coatings. Technical Data Sheet 01/01/2014 AKS PS POLYMER SILICATE COATING MORTAR
Technical Data Sheet 01/01/2014 AKS PS POLYMER SILICATE COATING MORTAR Product Description AKS-PS it a 2 or 3 component, solvent free polymer-silicate, trowel applied Performance Coating which offers optimum
Surface Protection Systems
Surface Protection Systems Industrial Corrosion Protection Applications Technology Bekaplast Bolted Lining 8408SKCe2c.indd 2 11.04.2012 17:13:54 Description of the System Bekaplast Bolted Lining is a thermoplastic
DURO-SHIELD ROOF COATING CARE GUIDE TABLE OF CONTENTS
TABLE OF CONTENTS Overview 2 General 3 4 Inspections and Repairs 5 Semi-Annual Inspections 5 Minor Repairs 5 Emergency Repairs 5 www.duro-last.com 1 of 5 OVERVIEW Due to its constant exposure to heat,
PF-Series Gantry Crane
SPANCO PRODUCT SPECIFICATIONS 1 PF-Series Gantry Crane This guide can be used to prepare a bid specification for the incorporation of a PF-Series Gantry Crane into a competitive bid project or application.
Jupiter 2 Installation Guidelines
Xplornet Tech Tool 1195 Jupiter 2 Installation Guidelines This TechTool provides reminders and tips on how to properly install and provision for Jupiter 2. Many of these reminders are important and failure
Welding on the chassis frame. Weld areas IMPORTANT!
General General All welding must be carried out professionally by trained personnel. Avoid welding on the chassis frame as all welding increases the risk of fracture formation in the area around the weld.
Thermal Transfer Polyester Label Material
Thermal Transfer Polyester Label Material Technical Data May 2017 Product Description Construction Polyester Label Materials 7871, 7872 and 7873 are gloss polyester label materials that offer premium durability
Installation manual Flat Roof Insert System
Van der Valk Solar Systems TRACKNG AND FXED SOLAR MOUNTNG SYSTEMS nstallation manual System Use in combination with installation manual 1-2-3 PV Planner Version 12 EN General user instructions Solar mounting
SECTION VIBRATION CONTROLS FOR HVAC PIPING AND EQUIPMENT
SECTION 230548 - PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following: 1. Elastomeric Isolation pads. 2. Elastomeric Isolation mounts. 3. [Freestanding] [Restrained] [Freestanding and restrained]
greenline fischer greenline
greenline fischer greenline The first range of fixing products with renewable resources. greenline The fixing assortment made with sustainable natural sources. Sustainable building With the introduction
SPECIFICATION: LINE TAPS FOR ALUMINIUM/ACSR AND COPPER CONDUCTORS
Page no. :1 of 11 SPECIFICATION: LINE TAPS FOR ALUMINIUM/ACSR AND COPPER CONDUCTORS Prepared by: Eng. T. Lev (-חתום-) Checked by: I. Bester (-חתום (- Approved by: Eng. Y. Samoocha (-חתום (- 1 Page no.
Fastening technology for metals and plastics
Fastening technology for metals and plastics Thread forming screws for metals TAPTITE 2000 (M1 approx. M10) The TAPTITE 2000 allows chipless forming during the fastening process. It is characterized by
PRICES: DESIGN: TAXES:
CLICK HERE TO START TERMS AND CONDITIONS AGREEMENTS: All agreements are subject to strikes, accidents or other causes beyond our control. GUARANTEE: We guarantee for one year from date of delivery our
NOTES FOR THE PERFORMANCE BASED SPECIFICATION FOR TRAFFIC SIGNS
CONTENTS NOTES FOR THE PERFORMANCE BASED SPECIFICATION FOR TRAFFIC SIGNS 1. SCOPE... 2 2. RELATED DOCUMENTS... 2 3. DEFINITIONS... 2 4. COMPLIANCE... 2 5. SIGN FACE DESIGN... 3 6. VISIBILITY... 3 6.1 Performance
PRODUCT DATA SHEET Sika Unitherm Platinum
PRODUCT DATA SHEET Solvent free, ultra high build, two pack, modified epoxy resin based, intumescent fire protection coating for internally or externally exposed structural steel. Ideal for in-shop application.
Fixings, bonds and clamps
Square tape clamp Material 25 x 3mm Copper 0.12kg CT105-H 25 x 6mm Copper 0.30kg CT110-H 50 x 6mm Copper 0.60kg CT115-H Manufactured from high quality copper and aluminium alloys. Simple to install, providing
Fabrications, Safety & Lighting Solutions. Product Data Sheet. Kingspan Day-Lite Trapezoidal Plus KS1000 DLTR PLUS 1.3 & 0.8
Fabrications, Safety & Lighting Solutions Kingspan Day-Lite KS1000 DLTR PLUS 1.3 & 0.8 Applications Designed to be an integral part of the Trapezoidal Roof panel system, Kingspan Day-Lite is a range of
BIRSTA 1P N2 WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE. Doc. No.: Birsta 1P N2 - Rev. 0
BIRSTA 1P N2 WORKING DESCRIPTION INSTALLATION, REPAIRS AND MAINTENANCE Doc. No.: Birsta 1P N2 - Rev. 0 Working Description Prepared by: Fredrik Sangö Doc. no.: Birsta 1P N2 Introduction/data: Birsta 1P
Features: Specifications: Applications:
SILVER MIRROR Silver Mirror is a kind of functional glass, which is produced through a series of processing work(cleaning,spraying-sensitized,silver-coated,copper-coated,second-time spraying-painted and
Sub-construction for longlight
modular skylights Sub-construction for longlight Sub-construction for longlight at 5-25 pitch modular skylights installed in a longlight solution are build on a sub-construction made of wood, steel or
IBC Mounting Systems. System solutions for all application areas
IBC Mounting Systems System solutions for all application areas IBC Mounting Systems System solutions for all application areas By using IBC Mounting Systems, you will find that our carefully designed
Good Husband Brand Remote Lighting Lifter
Good Husband Brand Remote Lighting Lifter National Patent Number:200520069085.5 200520075680.X 200520075677.8 200520075679.7 International Patent Number: PCT/CN2006/000409 Product Standard: Q/QABC002-2009
UNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 095113 - ACOUSTICAL PANEL CEILINGS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. AC: Articulation
Why Does Rust Occur? 7.1 IN GENERAL
Why Does Rust Occur? 7.1 IN GENERAL Rust damage on products costs large sums every year, and can also cause breakdowns through various kinds of corrosion weakening supporting structures. There are therefore
Allround Scaffolding. Layher Allround Bridging System Instructions for Assembly and Use. Modular truss system for wide spans
Layher Allround Bridging System Instructions for Assembly and Use Modular truss system for wide spans Certification according to DIN ISO 9001/EN 29 001 by TÜV-CERT Allround Scaffolding } CONTENT 1. Introduction...3
HELIOSTAR 252, 218 HORIZONTAL, FREE INSTALLATION
HELIOSTAR 252, 218 HORIZONTAL, FREE INSTALLATION INSTALLATION INSTRUCTIONS ENERGY AND SANITARY SYSTEMS Installation requirements General requirements The free-standing installation set is to be used for
Select adequate material of construction
NEWSLETTER March 2011 Select adequate material of construction Corrosion is recognized as one of the most serious problems in our modern societies and the resulting losses each year are in the hundreds
APPLICATION GUIDELINES EXTERIOR DECK SYSTEM
APPLICATION GUIDELINES EXTERIOR DECK SYSTEM Revision 6 Issue Date: 15 th September 2015 Registered Office The AkzoNobel Building, Wexham Road, Slough, SL2 5DS Page 1 CONTENTS Page 1. SCOPE AND PURPOSE
Mapefix PE Wall. Chemical anchor for masonry and light loads
Mapefix PE Wall Chemical anchor for masonry and light loads European Technical Approval ETAG 029 M8 M12 AREAS OF USE Mapefix PE Wall is an adhesive for chemically anchoring metal bars in holes made in
Smart Solutions for the Design and Renovation of Facades. Building Wrap Film instead of Paint
Smart Solutions for the Design and Renovation of Facades Building Wrap Film instead of Paint RENOLIT REFACE Gives Facades a Fresh, New Appearance Versatile, Durable and Sustainable. Customise a building