TOTAL OCCUPANTS = 28 OCC

Transcription

1 GENERAL NOTE 1. THE DRAWING AND THE PECIFICATION ARE PREPARED TO HOW THE ARCHITECT' INTENT IN THE DEIGN AND CONTRUCTION OF THE PROJECT. IN ALL MATTER RELATED TO THE UE OR INTERPRETATION OF THEE VARIOU DRAWING OR PECIFICATION, THE ARCHITECT' WRITTEN TATEMENT HALL BE CONIDERED FINAL. 2. ALL WORK HALL BE DONE IN ACCORDANCE WITH THE APPLICABLE CODE. 3. THE CONTRACTOR HALL VERIFY ALL DIMENION AND CONDITION ON ITE AND NOTIFY THE ARCHITECT IN WRITING OF ANY DICREPANCIE PRIOR TO COMMENCING THE WORK. CONTRUCTION THAT PROCEED BEYOND CONFORMANCE WITH THEE REQUIREMENT HALL BE PERFORMED AT CONTRACTOR OLE RIK. 4. HOULD UNFOREEEN CONDITION NECEITATE CONTRUCTION NOT IN ACCORDANCE WITH THEE DRAWING, THE CONTRACTOR HALL NOTIFY AND UBMIT TO THE ARCHITECT THE PROPOED METHOD TO ACCOMPLIH THE DEIGN INTENT PRIOR TO PROCEEDING WITH THE CONTRUCTION. 5. THE CONTRACTOR HALL CONFIRM CONNECTION LOCATION FOR UTILITIE UCH A ANITARY EWER, GA LINE, ELECTRIC, WATER FOR THE BUILDING PRIOR TO COMMENCING CONTRUCTION. 6. HOULD A DICREPANCY APPEAR IN THE DRAWING OR THE PECIFICATION, THE CONTRACTOR HALL NOTIFY THE ARCHITECT PRIOR TO PROCEEDING WITH CONTRUCTION. CONTRUCTION THAT PROCEED BEYOND CONFORMANCE WITH THEE REQUIREMENT HALL BE PERFORMED AT CONTRACTOR' OLE RIK. 7. PROTECT FROM DAMAGE ALL TRUCTURE, FINIHE, UTILITIE, EQUIPMENT, VEGETATION, ETC. INDICATED TO REMAIN. WORK THAT EFFECT THE TRUCTURAL INTEGRITY OF THE BUILDING HALL BE COORDINATED WITH THE ARCHITECT PRIOR TO PROCEEDING WITH THE WORK. PROVIDE TEMPORARY PROTECTIVE DUT AND WEATHER TIGHT ENCLOURE WHERE AND WHEN REQUIRED BY THE AUTHORITY HAVING JURIDICTION. 8. THE CONTRACTOR HALL ADEQUATELY BRACE AND PROTECT ALL WORK DURING CONTRUCTION AGAINT DAMAGE, BREAKAGE, COLLAPE, DITORTION AND MIALIGNMENT IN ACCORDANCE TO THE APPLICABLE CODE, TANDARD OF GOOD PRACTICE AND THE AUTHORITY HAVING JURIDICTION. 9. THE CONTRACTOR HALL COORDINATE WORKMEN' PARKING AND DELIVERY LOCATION WITH THE OWNER. 10. THE ARCHITECT HALL NOT BE REPONIBLE FOR THE UPERVIION OF THE CONTRUCTION. 11. GENERAL CONTRACTOR HALL PROVIDE A LIT OF ALL UBCONTRACTOR TO THE OWNER PRIOR TO IGNING OF CONTRACT AND FURNIH A WAIVER OF LIEN FOR ALL WORK AND MATERIAL UPON COMPLETION OF EACH TRADE WORK. 12. THE WORK INCLUDE ALL CUTTING AND PATCHING AND RETORATION OF AREA DITURBED DURING THE EXECUTION OF THI CONTRACT. MATCH TYPE, COLOR, QUALITY, TEXTURE, PATTERN, COURING, ETC. OF ALL ADJACENT URFACE (NEW AND/OR.) 13. THE CONTRACTOR HALL ECURE AND PAY FOR ALL PERMIT AND INPECTION, ALL FINAL APPROVAL AND CERTIFICATE OF OCCUPANCY (AT THE COMPLETION OF CONTRUCTION) A REQUIRED IN ACCORDANCE WITH APPLICABLE CODE AND THE AUTHORITY HAVING JURIDICTION. 14. THE BUILDING AND GROUND HALL BE KEPT CLEAN AT ALL TIME. REMOVE ALL DEBRI FROM THE ITE TO A POINT OF LEGAL DIPOAL A APPROVED BY THE AUTHORITY HAVING JURIDICTION. ONLY MATERIAL AND EQUIPMENT NECEARY FOR THI PROJECT ARE TO BE TORED ON ITE. 15. THE CONTRACTOR HALL TORE MATERIAL, DIPOE OF DEBRI, COORDINATE AND CHEDULE THE WORK IN COOPERATION WITH THE OWNER FOR MINIMUM DIRUPTION; MAINTAIN CLEAR ACCE TO THE BUILDING AND THE ITE AT ALL TIME; PROVIDE AND MAINTAIN ALL AFETY BARRICADE, AFETY DEVICE, BARRIER, ETC. TO PROTECT PERON AND PROPERTY IN ACCORDANCE WITH ALL LOCAL AND TATE REGULATION. CODE ANALYI JURIDICTION APN NEVADA TATE PUBLIC WORK DIVIION & NEVADA TATE FIRE MARHALL 1) CODE YEAR / TYPE 2012 IBC, 2012 IFC, 2012 IECC, 2011 NEC, 2012 UMC, 2012 UPC. 2) OCCUPANCY CLAIFICATION (IBC chapter 3) B (TI COPE) 3) TYPE OF CONTRUCTION (IBC chapter 6) II-B 4) FIRE PRINKLER (IBC 903, 903.3) YE, 5) FIRE ALARM (IBC 907) YE, 6) OCCUPANT LOAD (IBC 1004, , Table ) / / ROOM ROOM 622 1:50 NET = 13 OCC 414 1:50 NET = 9 OCC 267 1:50 GRO = 6 OCC TOTAL OCCUPANT = 28 OCC 7) NUMBER OF EXIT (IBC , 1021, and Tables , , ) EXIT REQUIRED AT EACH PACE 1 EXIT PROVIDED AT EACH PACE 1 EXIT WIDTH REQUIRED AT () 48 OCC x 0.2 = 9.6" EXIT WIDTH PROVIDED AT () 32" ALLOWABLE TRAVEL DITANCE (IBC ) LONGET TRAVEL DITANCE: 300' MAXIMUM (EE PLAN) 8) PACE REQUIRING FIRE REITANCE RATED EPARATION (IBC 420, 509, 706, 707, 708, 709, 711, , , 1022, 1023, 3006, Tables 509, ) NONE REQUIRED 9) REQUIRED PLUMBING FIXTURE (IBC 2902 and Table ): RETROOM ARE NO QUARE FOOTAGE I BEING ADDED AND OCCUPANCY I NOT CHANGING. ITE PLAN WENON TREET n o r t h OVERALL PLAN THOMA AND MACK AREA OF WORK - LOWER LEVEL MENDENHALL DRAWING INDEX GENERAL ARCHITECTURAL MECHANICAL ELECTRICAL NO. HELLO G000 G001 G002 A100 A101 A102 A103 A M000 M101 E000 E001 E201 E301 E500 NOTE, ITE PLAN AND INDEX PECIFICATION PECIFICATION PECIFICATION DEMOLITION PLAN FLOOR PLAN REFLECTED CEILING PLAN FINIH FLOOR PLAN & DETAIL HEET DOOR CHEDULE, WINDOW CHEDULE & DETAIL ALTERNATE MECHANICAL COVER HEET MECHANICAL PLAN ELECTRICAL COVER HEET ELECTRICAL PECIFICATION LIGHTING CEILING PLAN POWER PLAN RENOVATION UNLV Project #: MDC-1802 ELECTRICAL INGLE LINE DIAGRAM AND CHEDULE FM/PWD ubmittal 1 2 3, CONTRACTOR HALL UBMIT IN WRITING PROPOAL FOR ALL CHANGE TO THE CONTRACTED COPE OF WORK FOR REVIEW AND APPROVAL BY THE ARCHITECT AND OWNER PRIOR TO COMMENCEMENT OF ALL UCH WORK. CONTRUCTION THAT PROCEED BEYOND CONFORMANCE WITH THEE REQUIREMENT HALL BE PERFORMED AT CONTRACTOR' OLE RIK. AREA OF WORK 17. THE CONTRACTOR HALL BE FULLY REPONIBLE FOR ALL MATERIAL DELIVERED TO THE ITE AND WILL AUME OWNERHIP OF AME UNTIL THEY HAVE BEEN PROPERLY INTALLED. BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras 18. ALL WORKMANHIP AND MATERIAL HALL BE GUARANTEED FOR A MINIMUM PERIOD OF ONE (1) YEAR AFTER ACCEPTANCE BY THE OWNER, UNLE OTHERWIE NOTED. 19. FOR THE DURATION OF THE CONTRUCTION PERIOD, THE CONTRACTOR HALL AUME FULL REPONIBILITY FOR ALL DAMAGE CAUED BY HI FORCE OR UBCONTRACTOR' FORCE. THE CONTRACTOR HALL REPAIR AND/OR REPLACE ALL BROKEN PART, INCLUDING GLA, AT NO ADDITIONAL COT TO THE OWNER. 20. THE CONTRACTOR HALL PROVIDE ALL NECEARY TEMPORARY FACILITIE, UCH A HEAT ELECTRICITY AND WATER, REQUIRED FOR THE COPE OF WORK PER THE CONTRACT. TEMPORARY WORK OF ANY NATURE, INCLUDING TAIR, LADDER, RUNWAY AND CAFFOLDING, HALL MEET THE AFETY REQUIREMENT OF THE AUTHORITY HAVING JURIDICTION. 21. WORKMANHIP: IT I REQUIRED THAT ALL WORK HALL BE PERFORMED BY PERON WHO ARE KILLED AND EXPERIENCED IN THEIR REPECTIVE TRADE. ALL INTALLATION HALL OPERATE PROPERLY IN A HIGHET QUALITY MANNER. WORKMANHIP HALL CONFORM TO THE BET TRADE PRACTICE. FINIH URFACE HALL BE PLUMB AND LEVEL, TRAIGHT AND FREE FROM IMPERFECTION AND ET FIRMLY TO ACCURATE MEAUREMENT. FINIHED PRODUCT HALL BE TOTALLY FREE OF COVERING MATERIAL, LOOE AND FOREIGN MATERIAL, ETC. 22. CONTRACTOR AND UBCONTRACTOR HALL COORDINATE THEIR WORK WITH ADJACENT WORK AND COOPERATE WITH OTHER TRADE TO FACILITATE THE PROGRE OF THE WORK. EACH TRADE HALL AFFORD ALL OTHER TRADE EVERY REAONABLE OPPORTUNITY FOR INTALLATION OF THEIR COPE OF WORK AND FOR THE TEMPORARY TORAGE OF THEIR TOOL AND MATERIAL. 23. GENERAL CLEANING: UPON COMPLETION OF CONTRUCTION, THE CONTRACTOR HALL CLEAN ALL AREA, REMOVING ALL TAIN, DEBRI, ETC. REULTING FROM CONTRUCTION. THE CONTRACTOR HALL ALO CLEAN ALL GLA, INIDE AND OUT, WITH FINAL APPROVAL OF ALL CLEANING WORK TO BE PROVIDED BY THE OWNER AND ARCHITECT. IECC CALCULATION/YNOPI BUILDING WA UBMITTED UNDER EPARATE PERMIT. NO CHANGE ARE BEING MADE TO THE ENVELOPE OR THE BUILDING. FOR ELECTRICAL AND LIGHTING CALCULATION EE ELECTRICAL PLAN. FOR MECHANICAL CALCULATION EE MECHANICAL PLAN. ALTERNATE 1. REMODEL BREAK ROOM (A). NEW CAEWORK, KITCHEN EQUIPMENT, AND FINIHE, EE DRAWING ON A. 2. NEW LIGHTING FIXTURE (T-BAR LIGHTING) THROUGHOUT (), EE REFLECTED CEILING PLAN ON A, ZONED WITH (2) TWO DIMMABLE WITCHE. 3. FULLY REPLACE RUBBER FLOORING IN BREAK ROOM (A). 4. FULLY REPLACE RUBBER FLOORING IN COACHE LOCKER ROOM (). n o r t h EXITING PLAN 6 OCC TRAVEL DITANCE 102'-3" TRAVEL DITANCE 99'-4" 9 OCC OCC FILM ROOM TRAVEL DITANCE 75'-6" (HATCHED AREA NOT IN COPE) A 13 OCC PROJECT TEAM OWNER University of Nevada, Las Vegas P F ARCHITECT aptus 1200 outh 4th treet MECHANICAL/ELECTRICAL FEA Consulting Engineers 2821 West Horizon Ridge Parkway, #200 Henderson, Nevada P F NOTE, ITE PLAN AND INDEX HELLO

2 BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras ENERGY NOTE 1. ALL EXTERIOR DOOR HALL LIMIT AIR INFILTRATION AROUND THEIR PERIMETER IN A CLOED POITION. 2. PROVIDE EAL AT HEAD ILL AND JAMB. 3. OPEN EXTERIOR JOINT AROUND WINDOW AND DOOR FRAME, BETWEEN WALL AND FOUNDATION, BETWEEN WALL AND ROOF, BETWEEN WALL PANEL, AT PENETRATION OF UTILITIE THROUGH THE ENVELOPE, HALL BE EALED, CAULKED, OR WEATHER-TRIPPED TO LIMIT AIR LEAKAGE. FIRE DEPARTMENT NOTE 1. PROVIDE FIRE EXTINGUIHER A REQUIRED BY THE AUTHORITY HAVING JURIDICTION' FIRE DEPT. FIELD INPECTOR. 2. ALL EXIT DOOR HALL WING IN THE DIRECTION OF TRAVEL. 3. ALL EXIT DOOR HALL BE OPENABLE FROM THE INIDE WITHOUT THE UE OF A KEY OR ANY PECIAL KNOWLEDGE OR EFFORT. 4. PROVIDE EXIT IGN ABOVE EXIT WITHIN MIN. ¾ X 6 LETTER ON CONTRATING BACKGROUND. 5. PROVIDE ROOM CAPACITY IGN A REQUIRED BY FIRE DEPT. 6. MAINTAIN A MIN. OF 44 AILE TO EXIT OR PUBLIC WAY. 7. ANY DECORATION UED HALL BE NON-COMBUTIBLE OR FLAME PROOFED IN AN APPROVED MANNER. 8. UBMIT PLAN FOR FIXED FIRE EXTINGUIHING YTEM FOR APPROVAL OF INTALLATION AND OPERATION PRIOR TO INTALLATION TO THE AUTHORITY HAVING JURIDICTION' FIRE DEPT. 9. PROVIDE OUTIDE GA HUT OFF VALVE CONPICUOULY MARKED. 10. PROVIDE FIRE DAMPER WHERE AIR DUCT PENETRATE FIRE RATED WALL OR CEILING. ACCEIBILITY NOTE 1. ACCE TO THEE FACILITIE HALL BE PROVIDED AT PRIMARY ENTRANCE. 2. THE LOPE OF PUBLIC WALK HALL NOT EXCEED 5%. 3. WALKING URFACE LOPING LE THAT 6% HALL BE LIP REITANT. 4. PROVIDE A 60 X 60 MIN. LANDING ON TRIKE IDE OF DOOR W/ 44 MIN. LENGTH IN DIRECTION OF TRAVEL. 5. WALK HALL EXTEND 24 TO THE IDE OF THE TRIKE EDGE OF A DOOR OR GATE THAT WING TOWARD THE WALK. 6. THE LOPE OF RAMP HALL NOT EXCEED 8.33%. 7. RAMP HALL HAVE A NON-LIP URFACE. 8. RAMP HALL BE 48 WIDE MIN. 9. EVERY REQUIRED EXIT DOORWAY HALL BE IZED FOR A DOOR NOT LE THAN 3 FT. WIDE BY NOT LE THAT 6-8 HIGH CAPABLE OF OPENING 90 AND MOUNTED O THAT THE CLEAR WIDTH OF THE EXIT WAY I 32 MIN. 10. THREHOLD HOULD BE A MAX 1/2" ABOVE THE ADJACENT FLOOR OR MAX 1/2" WITHA 1/4" BEVEL AT 2: MAXIMUM EFFORT TO OPERATE DOOR HALL NOT EXCEED 5 LB. FOR INTERIOR DOOR OR 8.5 LB. FOR EXTERIOR DOOR WHEN FIRE DOOR ARE REQUIRED THE MAXIMUM EFFORT CAN BE INCREAED BUT NOT TO EXCEED 15 LB. 12. THE BOTTOM 10 OF ALL DOOR EXCEPT AUTOMATIC AND LIDING HALL HAVE A MOOTH UNINTERRUPTED URFACE. 13. PROVIDE LEVER TYPE HARDWARE PANIC BAR, PUH-PULL ACTIVATING BAR, OR OTHER HARDWARE DEIGNED TO PROVIDE PAAGE WITHOUT REQUIRING THE ABILITY TO GRAP THE OPENING HARDWARE. (30 TO 44 A.F.F.) 14. ALL DOORWAY LEADING TO ANITARY FACILITIE HALL HAVE 32 CLEAR UNOBTRUCTED OPENING. 15. PROVIDE 1.1/4 Ø GRAB BAR AT 33 A.F.F. AT REAR AND IDE OF W.C. GRAB BAR AT IDE TO BE 42 LONG AND EXTEND 24 BEYOND FRONT OF TOILET. GRAB BAR TO BE 36 LONG AT BACK W/ 1.1/2 CLR. FROM WALL. BAR FATENER AND MOUNTING UPPORT TO WITHTAND 250 LB. PER FT. IN BENDING, HEAR AND TRE. 17. WATER CLOET HALL HAVE A EAT HEIGHT OF 17 TO 19 FLUH VALVE TO HAVE MAX. 5 LB. OPERATING FORCE, AND 29 CLEAR FROM FLOOR TO BOTTOM OF APRON WITH KNEE. MTD. ON WIDE IDE OF 44 A.F.F. 18. URINAL TO HAVE A CLEAR PACE OF 30 X 48 IN FRONT. FLUH VALVE TO HAVE MAX. 5 LB. OPERATING FORCE. 19. PROVIDE 30 X 48 CLEAR PACE IN FRONT OF LAVATORY. 20. PROVIDE CLEARANCE OF 29, 8 DEPTH AT THE TOP AND A TOE CLEARANCE OF 9 FROM THE FLOOR AND 17 DEEP FROM THE FRONT OF THE LAVATORY. 21. INULATE HOT WATER AND DRAIN PIPE. 22. FAUCET CONTROL HALL BE OPERABLE WITH ONE HAND AND NOT REQUIRED GRAPING, PINCHING, OR TWITING. FAUCET TO HAVE MAX. 5 LB. OPERATING FORCE. 23. LOCATE TOWEL, ANITARY NAPKIN, AND WATE RECEPTACLE WITH ALL OPERABLE PART WITHIN 40 FROM FLOOR. 24. LOCATED TIUE DIPENER ON THE WALL WITHIN 12 OF THE FRONT EDGE OF THE TOILET EAT. 25. ELF CLOING VALVE TO REMAIN OPEN FOR MIN. 10 EC. DIVIION 1 - GENERAL DATA 1. THE PROJECT CONIT OF A MINOR REMODEL FOR THE, TUDY ROOM, AND COACH' LOCKER ROOM ON THE LOWER LEVEL OF THE MENDENHALL BUILDING. THE PROJECT I LOCATED ON 4505 OUTH MARYLAND PARKWAY LA VEGA, NEVADA 89154, A HOWN ON CONTRACT DOCUMENT PREPARED BY: APTU TH TREET, UITE 206 LA VEGA, NEVADA 2. DURING THE CONTRUCTION PERIOD THE CONTRACTOR HALL HAVE FULL UE OF THE PREMIE FOR CONTRUCTION OPERATION, INCLUDING UE OF THE ITE. THE CONTRACTOR UE OF THE PREMIE I LIMITED ONLY BY THE OWNER RIGHT TO PERFORM CONTRUCTION OPERATION WITH IT OWN FORCE OR TO EMPLOY EPARATE CONTRACTOR ON PORTION OF THE PROJECT. CONFINE OPERATION TO AREA WITHIN THE CONTRACT LIMIT INDICATED. PORTION OF THE ITE BEYOND AREA IN WHICH CONTRUCTION OPERATION ARE INDICATED ARE NOT TO BE DITURBED. KEEP DRIVEWAY AND ENTRANCE ERVING THE PREMIE CLEAR AND AVAILABLE TO THE OWNER AND OWNER' EMPLOYEE AT ALL TIME. DO NOT UE THEE AREA FOR PARKING OR TORAGE OF MATERIAL. 3. THE OWNER REERVE THE RIGHT TO OCCUPY AND TO PLACE AND INTALL EQUIPMENT IN COMPLETED AREA OF THE BUILDING, PRIOR TO UBTANTIAL COMPLETION PROVIDED THAT UCH OCCUPANCY DOE NOT INTERFERE WITH COMPLETION OF THE WORK. 4. COORDINATE CONTRUCTION ACTIVITIE INCLUDED UNDER VARIOU ECTION OF THEE CONTRUCTION DOCUMENT TO AURE EFFICIENT AND ORDERLY INTALLATION OF EACH PART OF THE WORK. WHERE INTALLATION OF ONE PART OF THE WORK I DEPENDENT ON INTALLATION OF OTHER COMPONENT, EITHER BEFORE OR AFTER IT OWN INTALLATION, CHEDULE CONTRUCTION ACTIVITIE IN THE EQUENCE REQUIRED TO OBTAIN BET REULT. WHERE AVAILABILITY OF PACE I LIMITED, COORDINATE INTALLATION OF DIFFERENT COMPONENT TO AURE MAXIMUM ACCEIBILITY FOR REQUIRED MAINTENANCE, ERVICE AND REPAIR. MAKE ADEQUATE PROVIION TO ACCOMMODATE ITEM CHEDULED FOR LATER INTALLATION. 5. COORDINATE CHEDULING AND TIMING OF REQUIRED ADMINITRATIVE PROCEDURE WITH OTHER CONTRUCTION ACTIVITIE TO AVOID CONFLICT AND ENURE ORDERLY PROGRE OF THE WORK. UCH ADMINITRATIVE ACTIVITIE INCLUDE, BUT ARE NOT LIMITED TO, THE FOLLOWING: PREPARATION OF CHEDULE. INTALLATION AND REMOVAL OF TEMPORARY FACILITIE. DELIVERY AND PROCEING OF UBMITTAL. PROGRE MEETING. PROJECT CLOE-OUT ACTIVITIE. 6. WITHIN 15 DAY OF NOTICE TO PROCEED, UBMIT A LIT OF THE CONTRACTOR PRINCIPLE TAFF AIGNMENT, INCLUDING THE UPERINTENDENT AND OTHER PERONNEL IN ATTENDANCE AT THE ITE; IDENTIFY INDIVIDUAL, THEIR DUTIE AND REPONIBILITIE; LIT THEIR ADDREE AND TELEPHONE NUMBER. 7. REQUIRE THE INTALLER OF EACH MAJOR COMPONENT TO INPECT BOTH THE UBTRATE AND CONDITION UNDER WHICH WORK I TO BE PERFORMED. DO NOT PROCEED UNTIL UNATIFACTORY CONDITION HAVE BEEN CORRECTED IN AN ACCEPTABLE MANNER. 8. COMPLY WITH MANUFACTURER' INTALLATION INTRUCTION AND RECOMMENDATION, TO THE EXTENT THAT THOE INTRUCTION AND RECOMMENDATION ARE MORE EXPLICIT OR TRINGENT THAN REQUIREMENT CONTAINED IN THE CONTRACT DOCUMENT. 9. INPECT MATERIAL OR EQUIPMENT IMMEDIATELY UPON DELIVERY AND AGAIN PRIOR TO INTALLATION. REJECT DAMAGED AND DEFECTIVE ITEM 10. PROVIDE ATTACHMENT AND CONNECTION DEVICE AND METHOD NECEARY FOR ECURING WORK. ECURE WORK TRUE TO LINE AND LEVEL. ALLOW FOR EXPANION AND BUILDING MOVEMENT. 11. PROVIDE UNIFORM JOINT WIDTH IN EXPOED WORK. ARRANGE JOINT IN EXPOED WORK TO OBTAIN THE BET VIUAL EFFECT. REFER QUETIONABLE CHOICE TO THE ARCHITECT FOR FINAL DECIION. 12. RECHECK MEAUREMENT AND DIMENION, BEFORE TARTING EACH INTALLATION. 13. INTALL EACH COMPONENT DURING WEATHER CONDITION AND PROJECT TATU THAT WILL ENURE THE BET POIBLE REULT. IOLATE EACH PART OF THE COMPLETED CONTRUCTION FROM INCOMPATIBLE MATERIAL A NECEARY TO PREVENT DETERIORATION. 14. WHERE MOUNTING HEIGHT ARE NOT INDICATED, INTALL INDIVIDUAL COMPONENT AT TANDARD MOUNTING HEIGHT RECOGNIZED WITHIN THE INDUTRY FOR THE PARTICULAR APPLICATION INDICATED. REFER QUETIONABLE MOUNTING HEIGHT DECIION TO THE ARCHITECT FOR FINAL DECIION. 15. COORDINATE PREPARATION AND PROCEING OF UBMITTAL WITH PERFORMANCE OF CONTRUCTION ACTIVITIE. ALLOW UFFICIENT REVIEW TIME O THAT INTALLATION WILL NOT BE DELAYED A A REULT OF THE TIME REQUIRED TO PROCE UBMITTAL, INCLUDING TIME FOR REUBMITTAL. 16. HOP DRAWING: UBMIT NEWLY PREPARED INFORMATION, DRAWN TO ACCURATE CALE. HIGHLIGHT, ENCIRCLE, OR OTHERWIE INDICATE DEVIATION FROM THE CONTRACT DOCUMENT. HOP DRAWING INCLUDE FABRICATION AND INTALLATION DRAWING, ETTING DIAGRAM, CHEDULE, PATTERN, TEMPLATE AND IMILAR DRAWING. INCLUDE THE FOLLOWING INFORMATION: DIMENION IDENTIFICATION OF PRODUCT AND MATERIAL INCLUDED. COMPLIANCE WITH PECIFIED TANDARD. NOTATION OF COORDINATION REQUIREMENT. NOTATION OF DIMENION ETABLIHED BY FIELD MEAUREMENT. COPIE OF ARCHITECT/ENGINEER DRAWING WILL NOT BE ACCEPTED. 17. UBMIT FULL-IZE, FULLY FABRICATED AMPLE CURED AND FINIHED A PECIFIED AND PHYICALLY IDENTICAL WITH THE MATERIAL OR PRODUCT PROPOED. AMPLE INCLUDE PARTIAL ECTION OF MANUFACTURED OR FABRICATED COMPONENT, CUT OR CONTAINER OF MATERIAL, COLOR RANGE ET, AND WATCHE HOWING COLOR, TEXTURE AND PATTERN. 18. UE KILLED CRAFTMEN. WORKMEN WHO DO NOT KNOW AND FOLLOW BAIC REQUIREMENT FOR HIGH QUALITY WORK OF THE TYPE THEY ARE PERFORMING HALL BE REMOVED FROM THE JOB. WHERE FINIH OPERATION DO NOT PRODUCE FINIH URFACE A PECIFIED, THE WORK HALL BE REMOVED AND CORRECTED A DIRECTED. 19. EMPLOY EXPERIENCED WORKER OR PROFEIONAL CLEANER FOR FINAL CLEANING. CLEAN EACH URFACE OR UNIT TO THE CONDITION EXPECTED IN A NORMAL, COMMERCIAL BUILDING CLEANING AND MAINTENANCE PROGRAM. COMPLY WITH MANUFACTURER' INTRUCTION. 20. COMPLETE THE FOLLOWING CLEANING OPERATION. REMOVE LABEL THAT ARE NOT PERMANENT. CLEAN TRANPARENT MATERIAL, INCLUDING MIRROR AND GLA IN DOOR AND WINDOW. REMOVE GLAZING COMPOUND AND OTHER UBTANCE THAT ARE NOTICEABLE VIION-OBCURING MATERIAL. REPLACE CHIPPED OR BROKEN GLA AND OTHER DAMAGED TRANPARENT MATERIAL. CLEAN EXPOED EXTERIOR AND INTERIOR HARD-URFACED FINIHE TO A DUT-FREE CONDITION, FREE OF TAIN, FILM AND IMILAR FOREIGN UBTANCE. RETORE REFLECTIVE URFACE TO THEIR ORIGINAL REFLECTIVE CONDITION. LEAVE CONCRETE FLOOR BROOM CLEAN. VACUUM CARPETED URFACE. WIPE URFACE OF MECHANICAL AND ELECTRICAL EQUIPMENT. REMOVE EXCE LUBRICATION AND OTHER UBTANCE. CLEAN LIGHT FIXTURE AND LAMP. CLEAN THE ITE, INCLUDING LANDCAPE DEVELOPMENT AREA, OF RUBBIH, LITTER AND OTHER FOREIGN UBTANCE. WEEP PAVED AREA BROOM CLEAN; REMOVE TAIN, PILL AND OTHER FOREIGN DEPOIT. RAKE GROUND THAT ARE NEITHER PAVED NOR PLANTED, TO A MOOTH EVEN-TEXTURED URFACE. 21. REFER TO THE GENERAL CONDITION FOR THE TERM OF THE CONTRACTOR PECIAL WARRANTY OF WORKMANHIP AND MATERIAL. MANUFACTURER' DICLAIMER AND LIMITATION ON PRODUCT WARRANTIE DO NOT RELIEVE THE CONTRACTOR OF THE WARRANTY ON THE WORK THAT INCORPORATE THE PRODUCT, NOR DOE IT RELIEVE UPPLIER, MANUFACTURER, AND UBCONTRACTOR REQUIRED TO COUNTERIGN PECIAL WARRANTIE WITH THE CONTRACTOR. 22. WHEN CORRECTING WARRANTED WORK THAT HA FAILED, REMOVE AND REPLACE OTHER WORK THAT HA BEEN DAMAGED A A REULT OF UCH FAILURE OR THAT MUT BE REMOVED AND REPLACED TO PROVIDE ACCE FOR CORRECTION OF WARRANTED WORK. 23. WHEN WORK COVERED BY A WARRANTY HA FAILED AND BEEN CORRECTED BY REPLACEMENT OR REBUILDING, REINTATE THE WARRANTY BY WRITTEN ENDOREMENT. THE REINTATED WARRANTY HALL BE EQUAL TO THE ORIGINAL WARRANTY WITH AN EQUITABLE ADJUTMENT FOR DEPRECIATION. DIVIION 1 - GENERAL DATA - (CONT'D) 24. UPON DETERMINATION THAT THE WORK COVERED BY A WARRANTY HA FAILED, REPLACE OR REBUILD THE WORK TO AN ACCEPTABLE CONDITION COMPLYING WITH REQUIREMENT OF THE CONTRACT DOCUMENT. THE CONTRACTOR I REPONIBLE FOR THE COT OF REPLACING OR REBUILDING DEFECTIVE WORK REGARDLE OF WHETHER THE OWNER HA BENEFITED FROM THE UE OF THE WORK THROUGH A PORTION OF IT ANTICIPATED UEFUL ERVICE LIFE. 25. THE OWNER REERVE THE RIGHT TO REJECT WARRANTIE AND TO LIMIT ELECTION TO PRODUCT WITH WARRANTIE NOT IN CONFLICT WITH REQUIREMENT OF THE CONTRACT DOCUMENT. THE OWNER REERVE THE RIGHT TO REFUE TO ACCEPT WORK FOR THE PROJECT WHERE A PECIAL WARRANTY, CERTIFICATION, OR IMILAR COMMITMENT I REQUIRED ON UCH WORK OR PART OF THE WORK, UNTIL EVIDENCE I PREENTED THAT ENTITIE REQUIRED TO COUNTERIGN UCH COMMITMENT ARE WILLING TO DO O. DIVIION 2 - ITEWORK DIVIION 3 - CONCRETE DIVIION 4 - MAONRY DIVIION 5 - METAL DIVIION 6 - WOOD & PLATIC 1. ROUGH CARPENTRY: a. PROVIDE AND INTALL BLOCKING, BACKING, PLYWOOD HEATHING, FURRING, AND MICELLANEOU LIGHT FRAMING REQUIRED FOR COMPLETION OF THE WORK, WHICH I GENERALLY NOT EXPOED; WHERE NOTED ON THE DRAWING AND A PECIFIED HEREIN. b. PROVIDE BLOCKING IN PARTITION FOR MOUNTING OF EQUIPMENT, HELVING, PLUMBING FIXTURE, ETC. c. ET ROUGH CARPENTRY ACCURATELY TO REQUIRED LEVEL AND LINE, WITH MEMBER PLUMB AND TRUE AND ACCURATELY CUT AND FITTED. ECURELY ATTACH WORK TO UBTRATE. d. PLACE WALL HEATHING WITH END JOINT TAGGERED. ECURE HEET OVER FIRM BEARING. MAINTAIN MINIMUM 1/16 INCH AND MAXIMUM 1/8 INCH PACING BETWEEN JOINT OF HEET ON WALL. PLACE PERPENDICULAR TO FRAMING MEMBER. DIVIION 7 - THERMAL/MOITURE PROTECTION 1. INULATION: a. COMPLY WITH INULATION MANUFACTURER' INTRUCTION APPLICABLE TO PRODUCT AND APPLICATION INDICATED. EXTEND INULATION FULL THICKNE A INDICATED TO ENVELOP ENTIRE AREA TO BE INULATED. CUT AND FIT TIGHTLY AROUND OBTRUCTION, AND FILL VOID WITH INULATION. REMOVE PROJECTION THAT INTERFERE WITH PLACEMENT. APPLY A INGLE LAYER OF INULATION OF REQUIRED THICKNE, UNLE OTHERWIE HOWN OR REQUIRED TO MAKE UP TOTAL THICKNE. b. PROTECT INTALLED INULATION AND VAPOR RETARDER FROM DAMAGE DUE TO HARMFUL WEATHER EXPOURE, PHYICAL ABUE, AND OTHER CAUE. PROVIDE TEMPORARY COVERING OR ENCLOURE WHERE INULATION WILL BE UBJECT TO ABUE AND CANNOT BE CONCEALED AND PROTECTED BY PERMANENT CONTRUCTION IMMEDIATELY AFTER INTALLATION. 2. INTERIOR PARTITION ACOUTICAL INULATION: PART 1 - GENERAL 1.01 UMMARY A. PROVIDE GLA FIBER ACOUTICAL INULATION FOR INTERIOR PARTITION A INDICATED IN BUILDING PLAN UBMITTAL A. PRODUCT DATA: UBMIT OWEN-CORNING PRODUCT LITERATURE, AMPLE AND INTALLATION INTRUCTION FOR PECIFIED INULATION DELIVERY, TORAGE AND HANDLING A. PROTECT INULATION FROM PHYICAL DAMAGE AND FROM BECOMING WET, OILED, OR COVERED WITH ICE OR NOW. COMPLY WITH MANUFACTURER' RECOMMENDATION FOR HANDLING, TORAGE AND PROTECTION DURING INTALLATION. B. LABEL INULATION PACKAGE TO INCLUDE MATERIAL NAME, PRODUCTION DATE AND/OR PRODUCT CODE LIMITATION A. DO NOT UE UNFACED INULATION IN EXPOED APPLICATION WHERE THERE I POTENTIAL FOR KIN CONTACT AND IRRITATION. B. KRAFT AND TANDARD FOIL FACING WILL BURN AND MUT NOT BE LEFT EXPOED. THE FACING MUT BE INTALLED IN UBTANTIAL CONTACT WITH THE UNEXPOED URFACE OF THE CEILING, WALL OR FLOOR FINIH. PROTECT FACING FROM ANY OPEN FLAME OR HEAT OURCE. PART 2 PRODUCT 2.01 MANUFACTURER A. OWEN-CORNING (OR APPROVED EQUAL) 2.02 OUND ATTENUATION A. TYPE: UNFACED GLA FIBER ACOUTICAL INULATION COMPLYING WITH ATM C 665, TYPE I B. URFACE BURNING CHARACTERITIC: 1. MAXIMUM FLAME PREAD: MAXIMUM MOKE DEVELOPED: 10 WHEN TETED IN ACCORDANCE WITH ATM E 84 C. COMBUTION CHARACTERITIC: PAE ATM E 136 D. FIRE REITANCE RATING: PAE ATM E A PART OF A COMPLETE FIRE TETED WALL AEMBLY. E. OUND TRANMIION CLA: TC 45 F. DIMENIONAL TABILITY: LINEAR HRINKAGE LE THAN 0.1% PART 3 EXECUTION 3.01 INPECTION AND PREPARATION A. EXAMINE UBTRATE AND CONDITION UNDER WHICH INULATION WORK I TO BE PERFORMED. A ATIFACTORY UBTRATE I ONE THAT COMPLIE WITH REQUIREMENT OF THE ECTION IN WHICH THE UBTRATE AND RELATED WORK I PECIFIED. B. VERIFY MECHANICAL AND ELECTRICAL ERVICE WITHIN THE WALL HAVE BEEN TETED AND INPECTED. C. OBTAIN INTALLER' WRITTEN REPORT LITING CONDITION DETRIMENTAL TO PERFORMANCE OF WORK IN THI ECTION. DO NOT PROCEED WITH INTALLATION OF INULATION UNTIL ATIFACTORY CONDITION HAVE BEEN CORRECTED. D. CLEAN UBTRATE OF UBTANCE HARMFUL TO INULATION INTALLATION - GENERAL A. COMPLY WITH MANUFACTURER' INTRUCTION FOR PARTICULAR CONDITION OF INTALLATION IN EACH CAE. B. BATT MAY BE FRICTION-FIT IN PLACE UNTIL THE INTERIOR FINIH I APPLIED. INTALL BATT TO FILL ENTIRE TUD CAVITY. IF TUD CAVITY I LE THAN 96" IN HEIGHT, CUT LENGTH TO FRICTION- FIT AGAINT FLOOR AND CEILING TRACK. WALL AND PENETRATION REQUIRE THAT INULATION BE CAREFULLY CUT TO FIT AROUND OUTLET, JUNCTION BOXE AND OTHER IRREGULARITIE. C. WHERE WALL ARE NOT FINIHED ON BOTH IDE OR INULATION DOE NOT FILL CAVITY DEPTH, UPPLEMENTARY UPPORT MUT BE PROVIDED TO HOLD PRODUCT IN PLACE. D. WHERE INULATION MUT EXTEND HIGHER THAN 8 FEET, TEMPORARY UPPORT CAN BE PROVIDED TO HOLD PRODUCT IN PLACE UNTIL FINIH MATERIAL I APPLIED. 3. EALANT: a. APPLY JOINT EALANT AT ALL INTERIOR OCCURRENCE OF CONTROL AND EXPANION JOINT ON EXPOED INTERIOR URFACE OF EXTERIOR WALL. PERIMETER JOINT OF EXTERIOR OPENING WHERE INDICATED. PERIMETER JOINT BETWEEN INTERIOR WALL URFACE AND FRAME OF INTERIOR DOOR, WINDOW AND OTHER INTERECTION OF DIIMILAR MATERIAL. b. PROVIDE JOINT EALANT THAT HAVE BEEN PRODUCED AND INTALLED TO ETABLIH AND MAINTAIN AIRTIGHT CONTINUOU EAL THAT ARE WATER REITANT, AND CAUE NO TAINING OR DETERIORATION OF JOINT UBTRATE. PROVIDE COLOR OF EXPOE EALANT A ELECTED BY ARCHITECT FROM MANUFACTURER FULL RANGE OF TANDARD COLOR. EALANT TO BE OF TYPE APPROPRIATE FOR INTENDED APPLICATION. c. ALL EALANT HALL BE APPLIED IN ACCORDANCE WITH MANUFACTURER PRINTED INTALLATION INTRUCTION APPLICABLE TO PRODUCT AND APPLICATION UNLE OTHERWIE INDICATED. DIVIION 8 - DOOR & WINDOW 1. GLAZING FURNIH AND INTALL GLAZING A HOWN ON DRAWING. COMPLY WITH RECOMMENDATION OF "FLAT GLA MARKETING AOC." (FGMA) AND "EALANT MANUAL" FOR ALL GLAZING AND EALANT. CLEAR FLOAT GLA HALL BE TYPE 1 (TRANPARENT GLA, FLAT); TEMPERED GLA HALL BE CLEAR A HOWN ON THE DRAWING AND HALL BE TYPE "FT" (FULLY TEMPERED). INULATING GLA HALL BE PREAEMBLED UNIT OF ORGANICALLY EALED PANE OF GLA ENCLOING A HERMETICALLY EALED DEHYDRATED AIR PACE COMPLYING WITH ATM E774 FOR GLA, AIR PACE, EALING YTEM, EALANT, PACER MATERIAL, CORNER DEIGN AND DEICCANT. EXTERIOR PANE TO BE CLEAR A INDICATED ABOVE; INTERIOR PANE TO BE CLEAR. GLAZING EALANT, TAPE, ETC., FOR INTALLATION HALL BE A RECOMMENDED BY THE MANUFACTURER. INTALLATION HALL BE IN TRICT ACCORDANCE W/ MANUFACTURER' RECOMMENDATION; ALL GLAZING HALL BE THOROUGHLY CLEANED AT THE COMPLETION OF THE PROJECT. CRATCHED, CHIPPED, BROKEN OR OTHERWIE DAMAGED GLA UNIT HALL BE REPLACED AT NO COT TO THE OWNER. 4. HOLLOW METAL DOOR AND FRAME 1.1 UBMITTAL A. PRODUCT DATA: FOR EACH TYPE OF PRODUCT INDICATED. INCLUDE CONTRUCTION DETAIL, MATERIAL DECRIPTION, CORE DECRIPTION, HARDWARE REINFORCEMENT, PROFILE, ANCHOR, FIRE-REITANCE RATING, AND FINIHE. B. DOOR HARDWARE UPPLIER I TO FURNIH TEMPLATE, TEMPLATE REFERENCE NUMBER AND/OR PHYICAL HARDWARE TO THE TEEL DOOR AND FRAME UPPLIER IN ORDER TO PREPARE THE DOOR AND FRAME TO RECEIVE THE FINIH HARDWARE ITEM. C. HOP DRAWING: INCLUDE THE FOLLOWING: 1. ELEVATION OF EACH DOOR DEIGN. 2. DETAIL OF DOOR, INCLUDING VERTICAL AND HORIZONTAL EDGE DETAIL AND METAL THICKNEE. 3. FRAME DETAIL FOR EACH FRAME TYPE, INCLUDING DIMENIONED PROFILE AND METAL THICKNEE. 4. LOCATION OF REINFORCEMENT AND PREPARATION FOR HARDWARE. 5. DETAIL OF ANCHORAGE, JOINT, FIELD PLICE, AND CONNECTION. 6. DETAIL OF ACCEORIE. 7. DETAIL OF MOLDING, REMOVABLE TOP, AND GLAZING. 8. DETAIL OF CONDUIT AND PREPARATION FOR POWER, IGNAL, AND CONTROL YTEM. D. AMPLE FOR VERIFICATION: 1. AMPLE ARE ONLY REQUIRED BY REQUET OF THE ARCHITECT AND FOR MANUFACTURE THAT ARE NOT CURRENT MEMBER OF THE TEEL DOOR INTITUTE. E. INFORMATIONAL UBMITTAL: 1.2 QUALITY AURANCE A. OURCE LIMITATION: OBTAIN HOLLOW METAL DOOR AND FRAME THROUGH ONE OURCE FROM A INGLE MANUFACTURER WHEREVER POIBLE. B. QUALITY TANDARD: IN ADDITION TO REQUIREMENT PECIFIED, COMPLY WITH ANI/DI A250.8, LATET EDITION, "RECOMMENDED PECIFICATION FOR TANDARD TEEL DOOR AND FRAME". C. PRE-UBMITTAL CONFERENCE: CONDUCT CONFERENCE IN COMPLIANCE WITH REQUIREMENT IN DIVIION 01 ECTION "PROJECT MEETING" WITH ATTENDANCE BY REPREENTATIVE OF UPPLIER, INTALLER, AND CONTRACTOR TO REVIEW PROPER METHOD AND PROCEDURE FOR INTALLING HOLLOW METAL DOOR AND FRAME AND TO VERIFY INTALLATION OF ELECTRICAL KNOCKOUT BOXE AND CONDUIT AT FRAME WITH ELECTRIFIED OR ACCE CONTROL HARDWARE. 1.3 DELIVERY, TORAGE, AND HANDLING A. DELIVER HOLLOW METAL WORK PALLETIZED, WRAPPED, OR CRATED TO PROVIDE PROTECTION DURING TRANIT AND PROJECT ITE TORAGE. DO NOT UE NON-VENTED PLATIC. B. DELIVER WELDED FRAME WITH TWO REMOVABLE PREADER BAR ACRO BOTTOM OF FRAME, TACK WELDED TO JAMB AND MULLION. C. TORE HOLLOW METAL WORK UNDER COVER AT PROJECT ITE. PLACE IN TACK OF FIVE UNIT MAXIMUM IN A VERTICAL POITION WITH HEAD UP, PACED BY BLOCKING, ON MINIMUM 4-INCH HIGH WOOD BLOCKING. DO NOT TORE IN A MANNER THAT TRAP EXCE HUMIDITY. 1. PROVIDE MINIMUM 1/4-INCH PACE BETWEEN EACH TACKED DOOR TO PERMIT AIR CIRCULATION. DOOR AND FRAME TO BE TACKED IN A VERTICAL UPRIGHT POITION. 1.4 PROJECT CONDITION A. FIELD MEAUREMENT: VERIFY ACTUAL DIMENION OF OPENING BY FIELD MEAUREMENT BEFORE FABRICATION. 1.5 COORDINATION A. COORDINATE INTALLATION OF ANCHORAGE FOR HOLLOW METAL FRAME. FURNIH ETTING DRAWING, TEMPLATE, AND DIRECTION FOR INTALLING ANCHORAGE, INCLUDING LEEVE, CONCRETE INERT, ANCHOR BOLT, AND ITEM WITH INTEGRAL ANCHOR. DELIVER UCH ITEM TO PROJECT ITE IN TIME FOR INTALLATION. 1.6 WARRANTY A. PECIAL WARRANTY: MANUFACTURER' TANDARD FORM IN WHICH MANUFACTURER AGREE TO REPAIR OR REPLACE DOOR THAT FAIL IN MATERIAL OR WORKMANHIP WITHIN PECIFIED WARRANTY PERIOD. B. WARRANTY INCLUDE INTALLATION AND FINIHING THAT MAY BE REQUIRED DUE TO REPAIR OR REPLACEMENT OF DEFECTIVE DOOR. PART 2 - PRODUCT 2.1 MANUFACTURER A. MANUFACTURER: UBJECT TO COMPLIANCE WITH REQUIREMENT, PROVIDE PRODUCT BY ONE OF THE FOLLOWING: 1. CECO DOOR PRODUCT. 2. CURRIE COMPANY. 3. ECURITY METAL PRODUCT. 2.2 MATERIAL A. COLD-ROLLED TEEL HEET: ATM A 1008/A 1008M, COMMERCIAL TEEL (C), TYPE B; UITABLE FOR EXPOED APPLICATION. D. PREFORMED METAL FRAME FOR LIGHT OPENING: MANUFACTURER' TANDARD FRAME FORMED OF INCH-THICK, COLD ROLLED TEEL HEET; WITH BAKED ENAMEL OR POWDER COATED FINIH; AND APPROVED FOR UE IN DOOR OF FIRE PROTECTION RATING INDICATED. MATCH PRE- FINIHED DOOR PAINT COLOR WHERE APPLICABLE. E. GLAZING: COMPLY WITH REQUIREMENT IN DIVIION 08 ECTION "GLAZING" AND WITH THE HOLLOW METAL DOOR MANUFACTURER' WRITTEN INTRUCTION. 1. FACTORY GLAZING: FACTORY INTALL GLAZING IN DOOR A INDICATED. DOOR WITH FACTORY INTALLED GLA TO INCLUDE ALL OF THE REQUIRED GLAZING MATERIAL. 2.7 ACCEORIE A. MULLION AND TRANOM BAR: JOIN TO ADJACENT MEMBER BY WELDING OR RIGID MECHANICAL ANCHOR. B. GROUT GUARD: FORMED FROM AME MATERIAL A FRAME, NOT LE THAN INCHE THICK. 2.8 FABRICATION A. FABRICATE HOLLOW METAL WORK TO BE RIGID AND FREE OF DEFECT, WARP, OR BUCKLE. ACCURATELY FORM METAL TO REQUIRED IZE AND PROFILE, WITH MINIMUM RADIU FOR THICKNE OF METAL. WHERE PRACTICAL, FIT AND AEMBLE UNIT IN MANUFACTURER' PLANT. WHEN HIPPING LIMITATION O DICTATE, FRAME FOR LARGE OPENING ARE TO BE FABRICATED IN ECTION FOR PLICING OR PLINING IN THE FIELD BY OTHER. B. TOLERANCE: FABRICATE HOLLOW METAL WORK TO TOLERANCE INDICATED IN ANI/DI A C. HOLLOW METAL DOOR: 1. EXTERIOR DOOR: PROVIDE OPTIONAL WEEP-HOLE OPENING IN BOTTOM OF EXTERIOR DOOR TO PERMIT MOITURE TO ECAPE WHERE PECIFIED. 2. GLAZED LITE: FACTORY CUT OPENING IN DOOR WITH APPLIED TRIM OR KIT TO FIT. FACTORY INTALL GLAZING WHERE INDICTED. 3. LOUVER: FACTORY CUT OPENING IN DOOR AND INTALL LOUVER INTO PREPARED OPENING WHERE INDICATED. 4. ATRAGAL: PROVIDE OVERLAPPING ATRAGAL A NOTED IN DOOR HARDWARE ET IN DIVIION 08 ECTION "DOOR HARDWARE" ON ONE LEAF OF PAIR OF DOOR WHERE REQUIRED BY NFPA 80 FOR FIRE-PERFORMANCE RATING OR WHERE INDICATED. EXTEND MINIMUM 3/4 INCH BEYOND EDGE OF DOOR ON WHICH ATRAGAL I MOUNTED. 5. CONTINUOU HINGE REINFORCEMENT: PROVIDE WELDED CONTINUOU 12 GAUGE TRAP FOR CONTINUOU HINGE PECIFIED IN HARDWARE ET IN DIVIION 08 ECTION "DOOR HARDWARE". D. HOLLOW METAL FRAME: 1. HIPPING LIMITATION: WHERE FRAME ARE FABRICATED IN ECTION DUE TO HIPPING OR HANDLING LIMITATION, PROVIDE ALIGNMENT PLATE OR ANGLE AT EACH JOINT, FABRICATED OF AME THICKNE METAL A FRAME. 2. WELDED FRAME: WELD FLUH FACE JOINT CONTINUOULY; GRIND, FILL, DRE, AND MAKE MOOTH, FLUH, AND INVIIBLE. A. WELDED FRAME ARE TO BE PROVIDED WITH TWO TEEL PREADER TEMPORARILY ATTACHED TO THE BOTTOM OF BOTH JAMB TO ERVE A A BRACE DURING HIPPING AND HANDLING. PREADER BAR ARE FOR BRACING ONLY AND ARE NOT TO BE UED TO IZE THE FRAME OPENING. 3. IDELIGHT AND TRANOM BAR FRAME: PROVIDE CLOED TUBULAR MEMBER WITH NO VIIBLE FACE EAM OR JOINT, FABRICATED FROM AME MATERIAL A DOOR FRAME. FATEN MEMBER AT CROING AND TO JAMB BY BUTT WELDING. 4. EQUAL RABBET FRAME: PROVIDE FRAME WITH EQUAL RABBET DIMENION UNLE GLAZING AND REMOVABLE TOP REQUIRE WIDER DIMENION ON GLA IDE OF FRAME., PECIFICATION G

3 BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras DIVIION 8 - (CONT'D) 5. HIGH FREQUENCY HINGE REINFORCEMENT: PROVIDE HIGH FREQUENCY HINGE REINFORCEMENT AT DOOR OPENING 48-INCHE AND WIDER WITH MORTIE BUTT TYPE HINGE AT TOP HINGE LOCATION. 6. CONTINUOU HINGE REINFORCEMENT: PROVIDE WELDED CONTINUOU 12 GAUGE TRAP FOR CONTINUOU HINGE PECIFIED IN HARDWARE ET IN DIVIION 08 ECTION "DOOR HARDWARE". 7. PROVIDE COUNTERUNK, FLAT- OR OVAL-HEAD EXPOED CREW AND BOLT FOR EXPOED FATENER UNLE OTHERWIE INDICATED FOR REMOVABLE TOP, PROVIDE ECURITY CREW AT EXTERIOR LOCATION. 8. MORTAR GUARD: PROVIDE GUARD BOXE AT BACK OF HARDWARE MORTIE IN FRAME AT ALL HINGE AND TRIKE PREP REGARDLE OF GROUTING REQUIREMENT. 9. FLOOR ANCHOR: WELD ANCHOR TO BOTTOM OF JAMB AND MULLION WITH AT LEAT FOUR POT WELD PER ANCHOR. 10. JAMB ANCHOR: PROVIDE NUMBER AND PACING OF ANCHOR A FOLLOW: A. MAONRY TYPE: LOCATE ANCHOR NOT MORE THAN 18 INCHE FROM TOP AND BOTTOM OF FRAME. PACE ANCHOR NOT MORE THAN 32 INCHE O.C. AND A FOLLOW: 1) TWO ANCHOR PER JAMB UP TO 60 INCHE HIGH. 2) THREE ANCHOR PER JAMB FROM 60 TO 90 INCHE HIGH. 3) FOUR ANCHOR PER JAMB FROM 90 TO 120 INCHE HIGH. 4) FOUR ANCHOR PER JAMB PLU 1 ADDITIONAL ANCHOR PER JAMB FOR EACH 24 INCHE OR FRACTION THEREOF ABOVE 120 INCHE HIGH. D. DRILL AND TAP DOOR AND FRAME TO RECEIVE NON-TEMPLATE, MORTIED, AND URFACE-MOUNTED DOOR HARDWARE. 3.3 INTALLATION A. GENERAL: INTALL HOLLOW METAL WORK PLUMB, RIGID, PROPERLY ALIGNED, AND ECURELY FATENED IN PLACE; COMPLY WITH DRAWING AND MANUFACTURER' WRITTEN INTRUCTION. B. HOLLOW METAL FRAME: INTALL HOLLOW METAL FRAME OF IZE AND PROFILE INDICATED. COMPLY WITH ANI/DI A AND NFPA 80 AT FIRE RATED OPENING. 1. ET FRAME ACCURATELY IN POITION, PLUMBED, ALIGNED, AND BRACED ECURELY UNTIL PERMANENT ANCHOR ARE ET. AFTER WALL CONTRUCTION I COMPLETE AND FRAME PROPERLY ET AND ECURED, REMOVE TEMPORARY BRACE, LEAVING URFACE MOOTH AND UNDAMAGED. HIM A NECEARY TO COMPLY WITH INTALLATION TOLERANCE. 2. FLOOR ANCHOR: PROVIDE FLOOR ANCHOR FOR EACH JAMB AND MULLION THAT EXTEND TO FLOOR, AND ECURE WITH POT-INTALLED EXPANION ANCHOR. 3. MAONRY WALL: COORDINATE INTALLATION OF FRAME TO ALLOW FOR OLIDLY FILLING PACE BETWEEN FRAME AND MAONRY WITH MORTAR. 4. GROUT REQUIREMENT: DO NOT GROUT HEAD OF FRAME UNLE REINFORCING HA BEEN INTALLED IN HEAD OF FRAME. DO NOT GROUT VERTICAL OR HORIZONTAL CLOED MULLION MEMBER. C. HOLLOW METAL DOOR: FIT HOLLOW METAL DOOR ACCURATELY IN FRAME, WITHIN CLEARANCE PECIFIED BELOW. HIM A NECEARY. 1. NON-FIRE-RATED TANDARD TEEL DOOR: A. JAMB AND HEAD: 1/8-INCH PLU OR MINU 1/16 INCH. B. BETWEEN EDGE OF PAIR OF DOOR: 1/8-INCH PLU OR MINU 1/16 INCH. C. BETWEEN BOTTOM OF DOOR AND TOP OF THREHOLD: MAXIMUM 3/8 INCH. D. BETWEEN BOTTOM OF DOOR AND TOP OF FINIH FLOOR (NO THREHOLD): MAXIMUM 3/4 INCH. 2. FIRE-RATED DOOR: INTALL DOOR WITH CLEARANCE ACCORDING TO NFPA 80. D. FIELD GLAZING: COMPLY WITH INTALLATION REQUIREMENT IN DIVIION 08 ECTION "GLAZING" AND WITH HOLLOW METAL MANUFACTURER' WRITTEN INTRUCTION. 3.4 ADJUTING AND CLEANING A. FINAL ADJUTMENT: CHECK AND READJUT OPERATING HARDWARE ITEM IMMEDIATELY BEFORE FINAL INPECTION. LEAVE WORK IN COMPLETE AND PROPER OPERATING CONDITION. REMOVE AND REPLACE DEFECTIVE WORK, INCLUDING HOLLOW METAL WORK THAT I WARPED, BOWED, OR OTHERWIE UNACCEPTABLE. B. REMOVE GROUT AND OTHER BONDING MATERIAL FROM HOLLOW METAL WORK IMMEDIATELY AFTER INTALLATION. C. PRIME-COAT AND PAINTED FINIH TOUCHUP: IMMEDIATELY AFTER ERECTION, AND MOOTH RUTED OR DAMAGED AREA OF PRIME COAT, OR PAINTED FINIHE, AND APPLY TOUCHUP OF COMPATIBLE AIR DRYING, RUT-INHIBITIVE PRIMER, ZINC RICH PRIMER (EXTERIOR AND GALVANIZED OPENING) OR FINIH PAINT. 1.6 DELIVERY, TORAGE, AND HANDLING A. COMPLY WITH REQUIREMENT OF REFERENCED TANDARD AND MANUFACTURER' WRITTEN INTRUCTION. B. PACKAGE DOOR INDIVIDUALLY IN CARDBOARD CARTON AND WRAP BUNDLE OF DOOR IN PLATIC HEETING. C. MARK EACH DOOR ON TOP RAIL WITH OPENING NUMBER UED ON HOP DRAWING. 1.7 PROJECT CONDITION A. ENVIRONMENTAL LIMITATION: DO NOT DELIVER OR INTALL DOOR UNTIL PACE ARE ENCLOED AND WEATHERTIGHT, WET WORK IN PACE I COMPLETE AND DRY, AND HVAC YTEM I OPERATING AND MAINTAINING AMBIENT TEMPERATURE AND HUMIDITY CONDITION AT OCCUPANCY LEVEL DURING THE REMAINDER OF THE CONTRUCTION PERIOD. B. ENVIRONMENTAL LIMITATION: DO NOT DELIVER OR INTALL DOOR UNTIL PACE ARE ENCLOED AND WEATHERTIGHT, WET WORK IN PACE I COMPLETE AND DRY, AND HVAC YTEM I OPERATING AND MAINTAINING TEMPERATURE BETWEEN 60 AND 90 DEG F (16 AND 32 DEG C) AND RELATIVE HUMIDITY BETWEEN 17 AND 50 PERCENT DURING THE REMAINDER OF THE CONTRUCTION PERIOD. 1.8 WARRANTY A. PECIAL WARRANTY: MANUFACTURER' TANDARD FORM IN WHICH MANUFACTURER AGREE TO REPAIR OR REPLACE DOOR THAT FAIL IN MATERIAL OR WORKMANHIP WITHIN PECIFIED WARRANTY PERIOD. 1. FAILURE INCLUDE, BUT ARE NOT LIMITED TO, THE FOLLOWING: a. WARPING (BOW, CUP, OR TWIT) MORE THAN 1/4 INCH (6.4 MM) IN A 42-BY-84-INCH (1067- BY-2134-MM) ECTION. b. TELEGRAPHING OF CORE CONTRUCTION IN FACE VENEER EXCEEDING 0.01 INCH IN A 3- INCH (0.25 MM IN A 76.2-MM) PAN. 2. WARRANTY HALL ALO INCLUDE INTALLATION AND FINIHING THAT MAY BE REQUIRED DUE TO REPAIR OR REPLACEMENT OF DEFECTIVE DOOR. 3. WARRANTY PERIOD FOR OLID-CORE EXTERIOR DOOR: ONE YEAR FROM DATE OF UBTANTIAL COMPLETION. 4. WARRANTY PERIOD FOR OLID-CORE INTERIOR DOOR: LIFE OF INTALLATION. PART 2 - PRODUCT 2.1 MANUFACTURER A. MANUFACTURER: UBJECT TO COMPLIANCE WITH REQUIREMENT, PROVIDE PRODUCT BY ONE OF THE FOLLOWING: 1. GRAHAM; AN AA ABLOY GROUP COMPANY. 2. MAIMAN; AN AA ABLOY GROUP COMPANY 2.2 DOOR CONTRUCTION, GENERAL A. CERTIFIED WOOD: FABRICATE DOOR WITH CORE NOT LE THAN 70 PERCENT OF WOOD PRODUCT PRODUCED FROM WOOD OBTAINED FROM FORET CERTIFIED BY AN FC-ACCREDITED CERTIFICATION BODY TO COMPLY WITH FC TD , "FC PRINCIPLE AND CRITERIA FOR FORET TEWARDHIP." B. LOW-EMITTING MATERIAL: FABRICATE DOOR WITH ADHEIVE AND COMPOITE WOOD PRODUCT THAT DO NOT CONTAIN UREA FORMALDEHYDE. C. LOW-EMITTING MATERIAL: FABRICATE DOOR WITH ADHEIVE THAT COMPLY WITH THE TETING AND PRODUCT REQUIREMENT OF THE CALIFORNIA DEPARTMENT OF HEALTH ERVICE' "TANDARD PRACTICE FOR THE TETING OF VOLATILE ORGANIC EMIION FROM VARIOU OURCE UING MALL-CALE ENVIRONMENTAL CHAMBER." D. WDMA I..1-A PERFORMANCE GRADE: EXTRA HEAVY DUTY. E. WDMA I..1-A PERFORMANCE GRADE: 1. EXTRA HEAVY DUTY: F. PARTICLEBOARD-CORE DOOR: 1. PARTICLEBOARD: ANI A208.1, GRADE LD PARTICLEBOARD: TRAW-BAED PARTICLEBOARD COMPLYING WITH ANI A208.1, GRADE LD-2 OR M-2, EXCEPT FOR DENITY. 3. BLOCKING: PROVIDE WOOD BLOCKING IN PARTICLEBOARD-CORE DOOR A FOLLOW: a. 5-INCH (125-MM) TOP-RAIL BLOCKING, IN DOOR INDICATED TO HAVE CLOER. b. 5-INCH (125-MM) BOTTOM-RAIL BLOCKING, IN EXTERIOR DOOR AND DOOR INDICATED TO HAVE KICK, MOP, OR ARMOR PLATE. c. 5-INCH (125-MM) MIDRAIL BLOCKING, IN DOOR INDICATED TO HAVE EXIT DEVICE. 4. PROVIDE DOOR WITH EITHER GLUED-WOOD-TAVE OR TRUCTURAL-COMPOITE-LUMBER CORE INTEAD OF PARTICLEBOARD CORE FOR DOOR INDICATED TO RECEIVE EXIT DEVICE. DIVIION 8 - (CONT'D) 2.3 DOOR FOR OPAQUE FINIH A. INTERIOR OLID-CORE DOOR: 1. GRADE: CUTOM. 2. FACE: ANY CLOED-GRAIN HARDWOOD OF MILL OPTION, HARDBOARD OR MDF. a. HARDBOARD FACE: AHA A135.4, CLA 1 (TEMPERED) OR CLA 2 (TANDARD). b. MDF FACE: ANI A208.2, GRADE 150 OR EXPOED VERTICAL AND TOP EDGE: ANY CLOED-GRAIN HARDWOOD. 4. CORE: PARTICLEBOARD TYPE LD CONTRUCTION: FIVE PLIE. TILE AND RAIL ARE BONDED TO CORE, THEN ENTIRE UNIT ABRAIVE PLANED BEFORE VENEERING. 2.4 PLATIC-LAMINATE-FACED DOOR A. INTERIOR OLID-CORE DOOR: 1. LOW PREURE LAMINATE FACE THERMALLY FUED TO CORE UNDER HEAT AND PREURE, COMPLYING WITH LAMINATING MATERIAL AOCIATION PRODUCT TANDARD AND TYPICAL PHYICAL PROPERTIE OF DECORATIVE OVERLAY. LMA COLOR OR WOOD GRAIN PATTERN <INERT COLOR OR WOOD GRAIN PATTERN>. 3. EXPOED VERTICAL, TOP AND BOTTOM EDGE: IMPACT-REITANT POLYMER EDGING, MINIMUM.040 THICK, APPLIED AFTER FACE. a. POLYMER EDGING COLOR: AME COLOR A FACE. 4. CORE: PARTICLEBOARD TYPE M FABRICATION A. FACTORY FIT DOOR TO UIT FRAME-OPENING IZE INDICATED. COMPLY WITH CLEARANCE REQUIREMENT OF REFERENCED QUALITY TANDARD FOR FITTING UNLE OTHERWIE INDICATED. 1. COMPLY WITH REQUIREMENT IN NFPA 80 FOR FIRE-RATED DOOR. B. FACTORY MACHINE DOOR FOR HARDWARE THAT I NOT URFACE APPLIED. LOCATE HARDWARE TO COMPLY WITH DHI-WDH-3. COMPLY WITH FINAL HARDWARE CHEDULE, DOOR FRAME HOP DRAWING, DHI A115-W ERIE TANDARD, AND HARDWARE TEMPLATE. 1. COORDINATE WITH HARDWARE MORTIE IN METAL FRAME TO VERIFY DIMENION AND ALIGNMENT BEFORE FACTORY MACHINING. 2. METAL ATRAGAL: FACTORY MACHINE ATRAGAL AND FORMED-TEEL EDGE FOR HARDWARE FOR PAIR OF FIRE-RATED DOOR. C. TRANOM AND IDE PANEL: FABRICATE MATCHING PANEL WITH AME CONTRUCTION, EXPOED URFACE, AND FINIH A PECIFIED FOR AOCIATED DOOR. FINIH BOTTOM EDGE OF TRANOM AND TOP EDGE OF RABBETED DOOR AME A DOOR TILE. 1. FABRICATE DOOR AND TRANOM PANEL WITH FULL-WIDTH, OLID-LUMBER[, RABBETED,] MEETING RAIL. PROVIDE FACTORY-INTALLED PRING BOLT FOR CONCEALED ATTACHMENT INTO JAMB OF METAL DOOR FRAME. D. OPENING: CUT AND TRIM OPENING THROUGH DOOR IN FACTORY. 1. LIGHT OPENING: TRIM OPENING WITH MOLDING OF MATERIAL AND PROFILE INDICATED. 2. GLAZING: FACTORY INTALL GLAZING IN DOOR INDICATED TO BE FACTORY FINIHED. COMPLY WITH APPLICABLE REQUIREMENT IN DIVIION 08 ECTION "GLAZING." 3. LOUVER: FACTORY INTALL LOUVER IN PREPARED OPENING. 2.6 HOP PRIMING A. DOOR FOR OPAQUE FINIH: HOP PRIME DOOR WITH ONE COAT OF WOOD PRIMER PECIFIED IN DIVIION 09 ECTION "INTERIOR PAINTING". EAL ALL FOUR EDGE, EDGE OF CUTOUT, AND MORTIE WITH PRIMER. B. DOOR FOR TRANPARENT FINIH: HOP PRIME DOOR WITH TAIN (IF REQUIRED), OTHER REQUIRED PRETREATMENT, AND FIRT COAT OF FINIH A PECIFIED IN DIVIION 09 ECTION "INTERIOR PAINTING OR TAINING AND TRANPARENT FINIHING." EAL ALL FOUR EDGE, EDGE OF CUTOUT, AND MORTIE WITH FIRT COAT OF FINIH. 2.7 FACTORY FINIHING A. GENERAL: COMPLY WITH REFERENCED QUALITY TANDARD FOR FACTORY FINIHING. COMPLETE FABRICATION, INCLUDING FITTING DOOR FOR OPENING AND MACHINING FOR HARDWARE THAT I NOT URFACE APPLIED, BEFORE FINIHING. 1. FINIH FACE, ALL FOUR EDGE, EDGE OF CUTOUT, AND MORTIE. TAIN AND FILLER MAY BE OMITTED ON TOP AND BOTTOM EDGE, EDGE OF CUTOUT, AND MORTIE. B. FINIH DOOR AT FACTORY. C. FINIH DOOR AT FACTORY THAT ARE INDICATED TO RECEIVE TRANPARENT FINIH. FIELD FINIH DOOR INDICATED TO RECEIVE OPAQUE FINIH. D. FINIH DOOR AT FACTORY WHERE INDICATED IN CHEDULE OR ON DRAWING A FACTORY FINIHED. E. UE ONLY PAINT AND COATING THAT COMPLY WITH THE TETING AND PRODUCT REQUIREMENT OF THE CALIFORNIA DEPARTMENT OF HEALTH ERVICE' "TANDARD PRACTICE FOR THE TETING OF VOLATILE ORGANIC EMIION FROM VARIOU OURCE UING MALL-CALE ENVIRONMENTAL CHAMBER." F. TRANPARENT FINIH: 1. GRADE: PREMIUM. 2. FINIH: WDMA TR-6 CATALYZED POLYURETHANE <INERT FINIH DEIGNATION>. 3. TAINING: A ELECTED BY ARCHITECT FROM MANUFACTURER' FULL RANGE. 4. EFFECT: EMIFILLED FINIH, PRODUCED BY APPLYING AN ADDITIONAL FINIH COAT TO PARTIALLY FILL THE WOOD PORE. 5. HEEN: ATIN. PART 3 - EXECUTION 3.1 EXAMINATION A. EXAMINE DOOR AND INTALLED DOOR FRAME BEFORE HANGING DOOR. 1. VERIFY THAT FRAME COMPLY WITH INDICATED REQUIREMENT FOR TYPE, IZE, LOCATION, AND WING CHARACTERITIC AND HAVE BEEN INTALLED WITH LEVEL HEAD AND PLUMB JAMB. 2. REJECT DOOR WITH DEFECT. B. PROCEED WITH INTALLATION ONLY AFTER UNATIFACTORY CONDITION HAVE BEEN CORRECTED. 3.2 INTALLATION A. HARDWARE: FOR INTALLATION, EE DIVIION 08 ECTION "DOOR HARDWARE." B. INTALLATION INTRUCTION: INTALL DOOR TO COMPLY WITH MANUFACTURER' WRITTEN INTRUCTION AND THE REFERENCED QUALITY TANDARD, AND A INDICATED. 1. INTALL FIRE-RATED DOOR IN CORREPONDING FIRE-RATED FRAME ACCORDING TO NFPA 80. C. JOB-FITTED DOOR: ALIGN AND FIT DOOR IN FRAME WITH UNIFORM CLEARANCE AND BEVEL A INDICATED BELOW; DO NOT TRIM TILE AND RAIL IN EXCE OF LIMIT ET BY MANUFACTURER OR PERMITTED FOR FIRE-RATED DOOR. MACHINE DOOR FOR HARDWARE. EAL EDGE OF DOOR, EDGE OF CUTOUT, AND MORTIE AFTER FITTING AND MACHINING. 1. CLEARANCE: PROVIDE 1/8 INCH (3.2 MM) AT HEAD, JAMB, AND BETWEEN PAIR OF DOOR. PROVIDE 1/8 INCH (3.2 MM) FROM BOTTOM OF DOOR TO TOP OF DECORATIVE FLOOR FINIH OR COVERING UNLE OTHERWIE INDICATED. WHERE THREHOLD I HOWN OR CHEDULED, PROVIDE 1/4 INCH (6.4 MM) FROM BOTTOM OF DOOR TO TOP OF THREHOLD UNLE OTHERWIE INDICATED. a. COMPLY WITH NFPA 80 FOR FIRE-RATED DOOR. 2. BEVEL NON-FIRE-RATED DOOR 1/8 INCH IN 2 INCHE (3-1/2 DEGREE) AT LOCK AND HINGE EDGE. 3. BEVEL FIRE-RATED DOOR 1/8 INCH IN 2 INCHE (3-1/2 DEGREE) AT LOCK EDGE; TRIM TILE AND RAIL ONLY TO EXTENT PERMITTED BY LABELING AGENCY. D. FACTORY-FITTED DOOR: ALIGN IN FRAME FOR UNIFORM CLEARANCE AT EACH EDGE. E. FACTORY-FINIHED DOOR: RETORE FINIH BEFORE INTALLATION IF FITTING OR MACHINING I REQUIRED AT PROJECT ITE. 3.3 ADJUTING A. OPERATION: RE-HANG OR REPLACE DOOR THAT DO NOT WING OR OPERATE FREELY. B. FINIHED DOOR: REPLACE DOOR THAT ARE DAMAGED OR THAT DO NOT COMPLY WITH REQUIREMENT. DOOR MAY BE REPAIRED OR REFINIHED IF WORK COMPLIE WITH REQUIREMENT AND HOW NO EVIDENCE OF REPAIR OR REFINIHING. C. OPAQUE FINIH: FIELD APPLIED OLID PAINTED COLOR OVER PECIFIED PAINT GRADE VENEER EXAMINATION A. EXAMINE DOOR AND INTALLED DOOR FRAME BEFORE HANGING DOOR. 1. VERIFY THAT FRAME COMPLY WITH INDICATED REQUIREMENT FOR TYPE, IZE, LOCATION, AND WING CHARACTERITIC AND HAVE BEEN INTALLED WITH LEVEL HEAD AND PLUMB JAMB. 2. REJECT DOOR WITH DEFECT. B. PROCEED WITH INTALLATION ONLY AFTER UNATIFACTORY CONDITION HAVE BEEN CORRECTED INTALLATION A. HARDWARE: FOR INTALLATION, EE DIVIION 8 ECTION "DOOR HARDWARE." B. INTALLATION INTRUCTION: INTALL DOOR TO COMPLY WITH MANUFACTURER' WRITTEN INTRUCTION AND THE REFERENCED QUALITY TANDARD, AND A INDICATED. 1. INTALL FIRE RATED DOOR IN CORREPONDING FIRE RATED FRAME ACCORDING TO NFPA 80. C. FACTORY FITTED DOOR: ALIGN IN FRAME FOR UNIFORM CLEARANCE AT EACH EDGE. D. FACTORY FINIHED DOOR: RETORE FINIH BEFORE INTALLATION IF FITTING OR MACHINING I REQUIRED AT PROJECT ITE ADJUTING A. OPERATION: RE-HANG OR REPLACE DOOR THAT DO NOT WING OR OPERATE FREELY. B. FINIHED DOOR: REPLACE DOOR THAT DO NOT COMPLY WITH REQUIREMENT. DOOR MAY BE REPAIRED OR REFINIHED IF WORK COMPLIE WITH REQUIREMENT AND HOW NO EVIDENCE OF REPAIR OR REFINIHING. DIVIION 9 - FINIHE 1. GYPUM DRYWALL YTEM: HALL CONIT OF METAL FRAMING UPPORT MEMBER (TUD AND/ OR FURRING CHANNEL) AND HALL INCLUDE INTALLATION OF YTEM, ANCHORING, TAPING, BEDDING, AND TEXTURING. ALL MEMBER HALL COMPLY WITH THICKNEE AND PACING A HOWN ON THE DRAWING. FURNIH ALL MATERIAL REQUIRED FOR COMPLETE INTALLATION. FURNIH AND INTALL METAL CORNER BEAD AT ALL EXTERIOR CORNER AND J-MOLDING AT ALL LOCATION WHERE GYPUM BOARD ABUTT A DIIMILAR MATERIAL.FURNIH AND INTALL WATERPROOF DRYWALL WHERE HOWN ON THE DRAWING AND, PECIFICALLY, ON ALL WALL OF TOILET ROOM. ATTACH ALL WALLBOARD WITH DRYWALL CREW PECIFICALLY DEIGNED AND IZED FOR THE PURPOE OF THE INTALLATION. IOLATE TEEL FRAMING FROM BUILDING TRUCTURE TO PREVENT TRANFER OF LOADING IMPOED BY TRUCTURAL MOVEMENT; PROVIDE LIP JOINT WHERE PARTITION AND WALL FRAMING ABUTT OVERHEAD TRUCTURE. FINIH ALL DRYWALL IN ACCORDANCE WITH MANUFACTURER' RECOMMENDATION, BUT IN NO CAE HALL FINIH TREATMENT BE LE THAN 3 COAT FINIH WORK. TEXTURE OF DRYWALL TO BE LIGHT "ORANGE PEEL" TEXTURE. 2. REILIENT BAE: FURNIH AND INTALL REILIENT BAE, EE CHEDULE FOR COLOR. ALL ADHEIVE HALL BE WATERPROOF. UE ONLY PRODUCT ACCEPTABLE TO AND/OR RECOMMENDED BY MANUFACTURER OF BAE MATERIAL. ALL JOINT HALL BE TIGHT AND CAREFULLY ALIGNED; ALL BAE HALL BE NEATLY LEVELED. REPLACE ANY MATERIAL DAMAGED DURING CONTRUCTION AT NO ADDITIONAL COT TO THE OWNER. UE PREMOLDED INIDE AND OUTIDE CORNER. 3. PAINTING: INCLUDE FIELD PAINTING OF ALL EXPOED BARE DUCTWORK, PIPE, HANGER, EXPOED TEEL AND IRON WORK, A WELL A PRIMED METAL URFACE OF MECHANICAL AND ELECTRICAL EQUIPMENT, GYPUM DRYWALL, FERROU METAL, WOOD DOOR (WHERE CHEDULED). IN GENERAL, ALL MATERIAL EXPOED TO VIEW AND NOT FACTORY PREFINIHED HALL BE PREPARED AND PAINTED. ALL PAINT MATERIAL HALL BE NEW, DELIVERED TO PROJECT ITE IN UN-OPENED CONTAINER. DO NOT APPLY PAINT TO DAMP OR WET URFACE. RE-PRIME URFACE PRIOR TO PAINTING IF FACTORY PRIME I CRATCHED OR MARRED DURING DELIVERY OR INTALLATION. CLEAN ALL URFACE THOROUGHLY PRIOR TO PAINTING, INCLUDING THE REMOVAL OF OIL OR GREAE. CHEDULE PAINTING O THAT DUT AND OTHER CONTAMINANT FROM THE CLEANING PROCE WILL NOT FALL ON NEWLY PAINTED URFACE. PROVIDE BARRIER COAT OVER INCOMPATIBLE PRIMER OR REMOVE AND RE-PRIME. UE NON-PETROLEUM BAED OLVENT TO CLEAN GALVANIZED URFACE PRIOR TO PAINTING. DO NOT PAINT OVER DIRT, RUT, CALE, GREAE, MOITURE, CUFFED URFACE OR OTHER CONDITION DETRIMENTAL TO FORMATION OF A HARD, DURABLE, MOOTH PAINT FILM. EE DRAWING FOR PAINT COLOR. EXTERIOR & INTERIOR PAINT CHEDULE - LOW VOC THE FOLLOWING PRODUCT ARE BAED ON FRAZEE PAINT. OTHER PRODUCT ARE ACCEPTABLE UPON APPROVAL BY THE ARCHITECT. INTERIOR URFACE GYPUM DRYWALL YTEM 1st COAT: C152 ULTRA TECH PRIMER/EALER 2nd COAT: ENDURABLE HEEN A ELECTED BY OWNER 3rd COAT: ENDURABLE HEEN A ELECTED BY OWNER WOOD - PAINTED 1T COAT: C312 ULTRA TECH INT/EXT ACRYLIC WOOD PRIMER 2nd COAT: 124 MIRRO GLIDE G 3rd COAT: 124 MIRRO GLIDE G WOOD - CLEAR FINIH -WATER BAED POLYURETHANE 3 COAT: VARATHANE DIAMOND POLYURETHANE ATIN OR EMIGLO FINIH WOOD - EMI-TRANPARENT TAIN FINIH 1st COAT: OLD MATER EMI-TRANPARENT TAIN 3 COAT: VARATHANE DIAMOND POLYURETHANE ATIN OR EMIGLO FINIH FERROU METAL 1st COAT: C309 ULTRA TECH UNIVERAL PRIMER 2nd COAT: 520 ACRYLIC DTM G 3rd COAT: 520 ACRYLIC DTM G METAL - GALVANIZED / ALUMINUM (ENAMEL FINIH) PRETREATMENT: KRUD KUTTER METAL ETCH 1st COAT: C309 ULTRA TECH UNIVERAL PRIMER 2nd COAT: 520 ACRYLIC DTM G 3rd COAT: 520 ACRYLIC DTM G ENAMEL FINIHE: GLO: 144 ENDURABLE ACRYLIC LATEX ENAMEL 143 MIRRO GLIDE 100% ACRYLIC ENAMEL EMIGLO: 124 MIRRO GLIDE 100% ACRYLIC ENAMEL EGGHELL: 126 MIRRO GLIDE 100% ACRYLIC ENAMEL LOW HEEN: 022 LOW GLO ACRYLIC LOW HEEN FLAT FINIH: 015 MAJETIC FLAT FINIH 4. TILE ETTING MATERIAL AND ACCEORIE PART 1 GENERAL 1.1 ECTION INCLUDE A. URFACE PREPARATION PRODUCT: BACKERBOARD, ELF-LEVELING UNDERLAYMENT, WATERPROOFING, UNCOUPLING AND CRACK IOLATION MEMBRANE, PRE-FORMED HOWER PAN, OUND REDUCTION MAT UNDERLAYMENT. B. ETTING MATERIAL: ARCHITECTURALLY ENGINEERED MORTAR YTEM, THIN-ET MORTAR, MEDIUM BED MORTAR, RAPID ETTING MORTAR, CHEMICAL REITANT MORTAR, CERAMIC TILE ADHEIVE. C. COLORED TILE GROUT: ANDED, NON-ANDED, INGLE COMPONENT AND EPOXY GROUT.. D. EDGE PROTECTION AND TRANITION PROFILE. E. TILE AND TONE CARE AND MAINTENANCE PRODUCT. 1.2 UBMITTAL A. UBMIT UNDER PROVIION OF ECTION B. PRODUCT DATA: MANUFACTURER' DATA HEET ON EACH PRODUCT TO BE UED, INCLUDING: 1. PREPARATION INTRUCTION AND RECOMMENDATION. 2. TORAGE AND HANDLING REQUIREMENT AND RECOMMENDATION. 3. INTALLATION METHOD. C. ELECTION AMPLE: FOR EACH FINIH PRODUCT PECIFIED, TWO COMPLETE ET OF COLOR CHIP REPREENTING MANUFACTURER' FULL RANGE OF AVAILABLE COLOR AND PATTERN. D. VERIFICATION AMPLE: FOR EACH FINIH PRODUCT PECIFIED, TWO AMPLE, MINIMUM IZE 6 INCHE (150 MM) QUARE, REPREENTING ACTUAL PRODUCT, COLOR, AND PATTERN. 1.3 QUALITY AURANCE A. MANUFACTURER QUALIFICATION: COMPANY PECIALIZING IN MANUFACTURING THE PRODUCT OF THI ECTION WITH MINIMUM TEN YEAR DOCUMENTED EXPERIENCE. B. INTALLER QUALIFICATION: COMPANY PECIALIZING IN PERFORMING THE WORK OF THI ECTION WITH MINIMUM FIVE YEAR DOCUMENTED EXPERIENCE. C. MOCK-UP: PROVIDE A MOCK-UP FOR EVALUATION OF URFACE PREPARATION TECHNIQUE AND APPLICATION WORKMANHIP. 1. LOCATE MOCK-UP ON ITE IN LOCATION AND IZE DIRECTED BY ARCHITECT. 2. FINIH AREA DEIGNATED BY ARCHITECT. DIVIION 9 - FINIHE (CONT'D) 3. DO NOT PROCEED WITH REMAINING WORK UNTIL WORKMANHIP, COLOR, AND HEEN ARE APPROVED BY ARCHITECT. 4. REFINIH MOCK-UP AREA A REQUIRED TO PRODUCE ACCEPTABLE WORK. 5. RETAIN AND MAINTAIN MOCK-UP DURING CONTRUCTION IN UNDITURBED CONDITION A A TANDARD FOR JUDGING COMPLETED UNIT OF WORK. 6. OBTAIN ARCHITECT' ACCEPTANCE OF MOCK-UP BEFORE TART OF FINAL UNIT OF WORK. D. CONDUCT CONFERENCE AT PROJECT ITE TO COMPLY WITH REQUIREMENT OF DIVIION 1 ECTION "PROJECT MEETING." 1.4 DELIVERY, TORAGE, AND HANDLING A. DELIVER AND TORE PACKAGED MATERIAL IN ORIGINAL CONTAINER WITH EAL UNBROKEN AND LABEL INTACT UNTIL TIME OF UE. COMPLY WITH REQUIREMENT OF ANI A137.1 FOR LABELING EALED TILE PACKAGE. B. PREVENT DAMAGE OR CONTAMINATION TO MATERIAL BY WATER, FREEZING, FOREIGN MATTER AND OTHER CAUE. C. TORE AND DIPOE OF OLVENT-BAED MATERIAL, AND MATERIAL UED WITH OLVENT-BAED MATERIAL, IN ACCORDANCE WITH REQUIREMENT OF LOCAL AUTHORITIE HAVING JURIDICTION. 1.5 PROJECT CONDITION A. MAINTAIN ENVIRONMENTAL CONDITION (TEMPERATURE, HUMIDITY, AND VENTILATION) WITHIN LIMIT RECOMMENDED BY MANUFACTURER FOR OPTIMUM REULT. DO NOT INTALL PRODUCT UNDER ENVIRONMENTAL CONDITION OUTIDE MANUFACTURER' ABOLUTE LIMIT. B. ENVIRONMENTAL: INTALL MORTAR, ET AND GROUT TILE WHEN URFACE AND AMBIENT TEMPERATURE I MINIMUM 50 DEGREE F (10 DEGREE C) AND MAXIMUM 90 DEGREE F (32 DEGREE C). CONULT WITH MANUFACTURER FOR PECIFIC REQUIREMENT. C. DO NOT INTALL MORTAR, ET OR GROUT TILE EXTERIOR WHEN INCLEMENT WEATHER CONDITION ARE EXPECTED WITHIN 48 HOUR AFTER WORK I COMPLETED UNLE PROPERLY PROTECTED. D. PROTECTION: PROTECT ADJACENT WORK URFACE DURING TILE WORK. CLOE ROOM OR PACE TO TRAFFIC OF ALL TYPE UNTIL MORTAR AND GROUT HA ET. E. AFETY: OBERVE THE MANUFACTURER' AFETY INTRUCTION INCLUDING THOE PERTAINING TO VENTILATION. 1.6 WARRANTY A. PRODUCT HALL BE PROVIDED WITH THE MANUFACTURER TANDARD WARRANTY A FOLLOW: 1. INTALLATION YTEM LIMITED WARRANTY: a. 5 YEAR. PART 2 PRODUCT 2.1 MANUFACTURER A. ACCEPTABLE MANUFACTURER: CUTOM BUILDING PRODUCT, WHICH I LOCATED AT: EAL BEACH BLVD.; EAL BEACH, CA 90740; TOLL FREE TEL: ; FAX: ; REQUET INFO (JACKIEL@CBPMAIL.NET); WEB: ARCHITECT.APX B. MAPEI. C. OR APPROVED EQUAL. 2.2 MATERIAL A. ANTI-FRACTURE MEMBRANE/CLEAVAGE MEMBRANE: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR IOLATING THE INTALLATION FROM CRACKING DUE TO MINOR UBTRATE MOVEMENT AND NORMAL TRUCTURAL DEFLECTION A PECIFIED IN ANI A AND COMPLYING WITH ANI A CUTOM BUILDING PRODUCT CRACK BUTER PRO CRACK PREVENTION MAT UNDERLAYMENT; HEET APPLIED PEEL N TICK MEMBRANE. B. WATERPROOFING AND ANTI-FRACTURE MEMBRANE: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR THIN-ET TILE INTALLATION AND COMPLYING WITH ANI FOR WATERPROOF MEMBRANE. 1. CUTOM BUILDING PRODUCT REDGARD WATERPROOFING AND CRACK PREVENTION MEMBRANE. C. MOITURE BARRIER YTEM: WHERE INDICATED ON THE DRAWING AND ELEWHERE A REQUIRED FOR THIN-ET TILE INTALLATION. 1. REDGARD WATERPROOFING AND CRACK PREVENTION MEMBRANE. EE MOITURE BARRIER INTALLATION INTRUCTION FOR REDGARD. REDUCE MVT FROM 12 LB/24 HR/1000 Q FT TO LE THAN 3 LB/24 HR/ 1000 Q FT. D. ELF-LEVELING UNDERLAYMENT: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED TO PROVIDE A FLAT, LEVEL URFACE FOR DIRECT RECEIPT OF TILE AND OTHER FLOOR COVERING ON DRY, INTERIOR INTALLATION. 1. CUTOM BUILDING PRODUCT LEVELLITE ELF-LEVELING UNDERLAYMENT FOR FILL UP TO 2 INCHE (51 MM) THICK. WEIGHT I 3 LB / Q FT AT 1/2 INCH THICK. E. CEMENTITIOU BACKER UNIT: COMPLYING WITH ANI A WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR FLOOR AND WALL, INTERIOR AND/OR EXTERIOR, WET AREA, AND DRY A RECOMMENDED UBTRATE FOR TILE, FIRE RATED WALL INTALLATION, HEAT HIELD WITH UL LITING FOR FLOOR AND WALL; INTALLATION TO COMPLY WITH ANI A AND MANUFACTURER' INTALLATION INTRUCTION. 1. 1/2 INCH (12 MM) WONDERBOARD BACKERBOARD (EXTERIOR OR INTERIOR FLOOR, WALL, CEILING, COUNTERTOP). F. CEMENTITIOU TILE ADHEIVE: 1. ANI A118.4, POLYMER-ENHANCED MORTAR: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR ETTING TILE A PECIFIED BY ANI A108.5, DRY-ET PORTLAND CEMENT MORTAR OR LATEX PORTLAND CEMENT MORTAR, OVER UBTRATE PREPARED ACCORDINGLY. a. FOR INTALLING LARGE FORMAT CERAMIC OR NATURAL TONE TILE (TILE WITH ONE EDGE GREATER THAN 15 INCHE), UTILIZING A MEDIUM BED MORTAR YTEM. 1) CUTOM BUILDING PRODUCT MEGALITE CRACK PREVENTION MORTAR. WITH HEAR BOND TRENGTH GREATER THAN 650 PI, PER ANI A118.4 EC FOR WALL AND FLOOR AEMBLIE WHERE MAXIMUM TRENGTH I DEIRED. G. TILE GROUT: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR FILLING THE JOINT BETWEEN TILE. COMPLIE WITH ANI A INTALLATION OF GROUT IN TILE WORK. 1. CHEMICAL REITANT, WATER-CLEANABLE TILE ETTING AND GROUTING EPOXY; ANI A118.3: a. CUTOM BUILDING PRODUCT FUION PRO INGLE COMPONENT, HIGH PERFORMANCE GROUT. MEETING THE PERFORMANCE REQUIREMENT OF ANI A118.3 AND A H. ELATOMERIC JOINT CAULK: PROVIDE WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED AT ALL JOINT BETWEEN FLOOR AND WALL AND AT JOINT BETWEEN TILE AND DIIMILAR MATERIAL. 1. CUTOM BUILDING PRODUCT COMMERCIAL 100 PERCENT ILICONE CAULK. CONFORM TO ATM C 920 FOR MOVEMENT JOINT IN HEAVY TRAFFIC AREA AND ATM C 794. I. CERAMIC AND NATURAL TONE TILE CARE AND MAINTENANCE: REQUIRED FOR PROPER MAINTENANCE OF THE COMPLETED TILE AEMBLY. 1. AQUA MIX EALER' CHOICE GOLD: WATER-BAED, PENETRATING EALER TO PROVIDE MAXIMUM TAIN PROTECTION. PART 3 EXECUTION 3.1 EXAMINATION A. EXAMINE URFACE, WHICH ARE TO RECEIVE TILE. B. DO NOT PROCEED WITH WORK UNTIL DEFECT OR CONDITION WHICH WOULD ADVERELY AFFECT QUALITY, EXECUTION AND PERMANENCE OF FINIHED TILE WORK ARE CORRECTED (ANI A108.3). C. IF UBTRATE PREPARATION I THE REPONIBILITY OF ANOTHER INTALLER, NOTIFY ARCHITECT OF UNATIFACTORY PREPARATION BEFORE PROCEEDING. 3.2 PREPARATION A. CLEAN URFACE THOROUGHLY PRIOR TO INTALLATION. B. PREPARE URFACE UING THE METHOD RECOMMENDED BY THE MANUFACTURER FOR ACHIEVING THE BET REULT FOR THE UBTRATE UNDER THE PROJECT CONDITION. C. CONDITION OF URFACE TO RECEIVE TILE. 1. AURE THAT URFACE TO RECEIVE TILE ARE TABLE, FLAT, FIRM, DRY, CLEAN AND FREE OF OIL, WAXE AND CURING COMPOUND. 2. DEFLECTION OF UBTRATE NOT TO EXCEED 1/360TH OF THE PAN 1/2 INCH (12 MM) IN 15 FEET (4.6 M) IN ACCORDANCE WITH ANI A ALLOW FOR LIVE AND IMPACT LOAD A WELL A DEAD LOAD WEIGHT OF TILE AND ETTING BED. 3. PROTECT ADJACENT URFACE PRIOR TO BEGINNING TILE WORK. 3.3 INTALLATION A. INTALL IN ACCORDANCE WITH MANUFACTURER' INTRUCTION. B. URFACE PREPARATION FOR TILE AND TONE WORK. 1. GENERAL: a. ALL UPPORTING URFACE HALL BE TRUCTURALLY OUND, OLID, TABLE, LEVEL, PLUMB, AND TRUE TO A TOLERANCE IN PLANE OF 1/4 INCH (6 MM) IN 10 FEET 0 INCH (3 M) FOR WALL, 1/4 INCH (6 MM) IN 10 FEET (3 M) FOR FLOOR WHEN PECIFIED FOR THIN-ET METHOD. WHEN INTALLING LARGE FORMAT TILE WITH ONE IDE GREATER THAN 15 INCHE OR 38 CM, THE TOLERANCE I REDUCED TO 1/8 INCH IN 10 FEET (3 MM IN 3 M). ANI A ECTION 2.6.2, PECIFICATION G

4 BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras DIVIION 9 - FINIHE (CONT'D) b. URFACE HALL BE CLEAN AND FREE OF DUT, OIL, GREAE PAINT, TAR, WAX, CURING COMPOUND, PRIMER, EALER, FORM RELEAE AGENT, LAITANCE, LOOELY BONDED TOPPING, LOOE PARTICLE OR ANY DELETERIOU UBTANCE AND DEBRI WHICH MAY PREVENT OR REDUCE ADHEION. c. MECHANICALLY AND AND CARIFY THE UBTRATE TO COMPLETELY REMOVE ALL PAINT, LOOELY BONDED TOPPING, LOOE PARTICLE AND CONTRUCTION DEBRI. d. NEUTRALIZE ANY TRACE OF TRONG ACID OR ALKALI. e. ALL UBTRATE HALL BE DRY. THE MOITURE CONTENT HALL NOT EXCEED 50 PERCENT. f. TURN OFF ALL FORCED VENTILATION AND RADIANT HEATING YTEM AND PROTECT WORK AGAINT DRAFT DURING INTALLATION AND FOR A PERIOD OF AT LEAT 72 HOUR AFTER COMPLETION. UE INDIRECT AUXILIARY HEATER TO MAINTAIN THE TEMPERATURE IN THE AREA AT THE RECOMMENDED WORKABLE LEVEL. VENT TEMPORARY HEATER TO EXTERIOR TO PREVENT DAMAGE TO TILE WORK FROM CARBON DIOXIDE BUILD-UP. g. PREWOOD, PARTICLEBOARD, CHIPBOARD, MAONITE, GYPUM FLOOR PATCHING COMPOUND, ABETO BOARD, LUAN AND IMILAR DIMENIONALLY UNTABLE MATERIAL ARE NOT ACCEPTABLE UBTRATE. h. BEFORE WORK COMMENCE EXAMINE THE AREA TO BE COVERED AND REPORT ANY FLAW OR ADVERE CONDITION IN WRITING TO THE ARCHITECT AND TO THE GENERAL CONTRACTOR. DO NOT PROCEED WITH WORK UNTIL URFACE AND CONDITION COMPLY WITH THE REQUIREMENT INDICATED IN ANI A108 PECIFICATION. 2. CONCRETE AND MAONRY: a. CONCRETE AND MAONRY URFACE MUT COMPLY WITH ANI A ECTION 3.2. b. ALL CONCRETE UBTRATE HALL BE AT LEAT 28 DAY OLD, COMPLETELY CURED AND FREE OF HYDROTATIC CONDITION, AND/OR MOITURE PROBLEM. 3. PLYWOOD: a. PLYWOOD UBFLOOR AND UNDERLAYMENT MUT COMPLY WITH ANI A ECTION OB PANEL: a. OB PANEL I NOT A UITABLE URFACE FOR DIRECT BONDING CERAMIC TILE. OB HOULD BE COATED WITH CUTOM BUILDING PRODUCT REDGARD WATERPROOFING AND ANTI-FRACTURE MEMBRANE PRIOR TO THE INTALLATION OF CERAMIC TILE. 5. BACKERBOARD UNIT INTALLATION OF FLOOR, DECK OR COUNTERTOP: a. CEMENTITIOU BACKERBOARD HALL BE INTALLED PER THE GUIDELINE IN ANI A WALL AND CEILING INTALLATION a. WALL AND CEILING URFACE MUT COMPLY WITH ANI A ECTION GYPUM URFACE: a. GYPUM BOARD HALL BE INTALLED PER THE GUIDELINE OF ANI A ECTION TEEL: a. TEEL UBTRATE HALL BE RIGID, OLIDLY FIXED, DRY, WELL ANDED AND FREE OF DUT, OIL, GREAE, PRIMER AND ALL DELETERIOU UBTANCE, WHICH MAY PREVENT OR DIMINIH THE BOND. 9. TILING OVER OLD UBTRATE: a. OLD CEMENT TERRAZZO, CERAMIC TILE PAVER, QUARRY TILE, VINYL AND VINYL COMPOITION FLOOR COVERING OTHER THAN CUHION VINYL HALL BE OUND, OLIDLY IN PLACE, FLAWLE, TRIPPED OR ANDED, CLEAN, FREE OF DUT, WAX, GREAE, EALER, OAP REIDUE AND ALL OTHER DELETERIOU UBTANCE WHICH MAY PREVENT OR REDUCE THE ADHEION. FOR FURTHER DETAIL, ANI A108.01, ECTION C. INTALL TILE IN ACCORDANCE WITH APPROPRIATE ANI A108 PECIFICATION AND MANUFACTURER' DIRECTION. D. EXPANION JOINT, CONTROL JOINT, INULATION JOINT, ETC., MUT BE LOCATED IN COMPLIANCE WITH TCA EJ171 AND FILLED WITH APPROPRIATE MATERIAL. 1. JOINT MUT BE CARRIED THROUGH ALL LAYER OF INTALLATION MATERIAL INCLUDING TILE, ETTING BED, MORTAR BED AND REINFORCING WIRE. REFER TO TCNA HANDBOOK, EJ171 AND ANI AN-3.8 FOR DETAIL ON PLACEMENT, IZE AND PECIFICATION OF MATERIAL.). E. INTALL GROUT IN ACCORDANCE WITH GROUT ANI A PECIFICATION AND MANUFACTURER' DIRECTION. F. INTALL ELATOMERIC TILE CAULK AROUND INK, TUB AND HOWER AND WHERE TILE MEET TILE OR ANOTHER URFACE. URFACE HOULD BE CLEAN, DRY AND FREE OF ALL CONTAMINATION. MAXIMUM JOINT WIDTH AND DEPTH HOULD NOT EXCEED 1/4 INCH (6 MM). G. EAL GROUT, TONE AND UNGLAZED TILE WITH AN APPROPRIATE EALER HOUR AFTER GROUT APPLICATION. 3.4 PROTECTION A. PROTECT INTALLED PRODUCT UNTIL COMPLETION OF PROJECT. B. TOUCH-UP, REPAIR OR REPLACE DAMAGED PRODUCT BEFORE UBTANTIAL COMPLETION. 3.5 CHEDULE A. INTALL TILE UING TCNA METHOD. 2.2 MATERIAL A. ANTI-FRACTURE MEMBRANE/CLEAVAGE MEMBRANE: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR IOLATING THE INTALLATION FROM CRACKING DUE TO MINOR UBTRATE MOVEMENT AND NORMAL TRUCTURAL DEFLECTION A PECIFIED IN ANI A AND COMPLYING WITH ANI A CUTOM BUILDING PRODUCT CRACK BUTER PRO CRACK PREVENTION MAT UNDERLAYMENT; HEET APPLIED PEEL N TICK MEMBRANE. B. WATERPROOFING AND ANTI-FRACTURE MEMBRANE: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR THIN-ET TILE INTALLATION AND COMPLYING WITH ANI FOR WATERPROOF MEMBRANE. 1. CUTOM BUILDING PRODUCT REDGARD WATERPROOFING AND CRACK PREVENTION MEMBRANE. C. MOITURE BARRIER YTEM: WHERE INDICATED ON THE DRAWING AND ELEWHERE A REQUIRED FOR THIN-ET TILE INTALLATION. 1. REDGARD WATERPROOFING AND CRACK PREVENTION MEMBRANE. EE MOITURE BARRIER INTALLATION INTRUCTION FOR REDGARD. REDUCE MVT FROM 12 LB/24 HR/1000 Q FT TO LE THAN 3 LB/24 HR/ 1000 Q FT. D. ELF-LEVELING UNDERLAYMENT: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED TO PROVIDE A FLAT, LEVEL URFACE FOR DIRECT RECEIPT OF TILE AND OTHER FLOOR COVERING ON DRY, INTERIOR INTALLATION. 1. CUTOM BUILDING PRODUCT LEVELLITE ELF-LEVELING UNDERLAYMENT FOR FILL UP TO 2 INCHE (51 MM) THICK. WEIGHT I 3 LB / Q FT AT 1/2 INCH THICK. E. CEMENTITIOU BACKER UNIT: COMPLYING WITH ANI A WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR FLOOR AND WALL, INTERIOR AND/OR EXTERIOR, WET AREA, AND DRY A RECOMMENDED UBTRATE FOR TILE, FIRE RATED WALL INTALLATION, HEAT HIELD WITH UL LITING FOR FLOOR AND WALL; INTALLATION TO COMPLY WITH ANI A AND MANUFACTURER' INTALLATION INTRUCTION. 1. 1/2 INCH (12 MM) WONDERBOARD BACKERBOARD (EXTERIOR OR INTERIOR FLOOR, WALL, CEILING, COUNTERTOP). F. CEMENTITIOU TILE ADHEIVE: 1. ANI A118.4, POLYMER-ENHANCED MORTAR: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR ETTING TILE A PECIFIED BY ANI A108.5, DRY-ET PORTLAND CEMENT MORTAR OR LATEX PORTLAND CEMENT MORTAR, OVER UBTRATE PREPARED ACCORDINGLY. a. FOR INTALLING LARGE FORMAT CERAMIC OR NATURAL TONE TILE (TILE WITH ONE EDGE GREATER THAN 15 INCHE), UTILIZING A MEDIUM BED MORTAR YTEM. 1) CUTOM BUILDING PRODUCT MEGALITE CRACK PREVENTION MORTAR. WITH HEAR BOND TRENGTH GREATER THAN 650 PI, PER ANI A118.4 EC FOR WALL AND FLOOR AEMBLIE WHERE MAXIMUM TRENGTH I DEIRED. G. TILE GROUT: WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED FOR FILLING THE JOINT BETWEEN TILE. COMPLIE WITH ANI A INTALLATION OF GROUT IN TILE WORK. 1. CHEMICAL REITANT, WATER-CLEANABLE TILE ETTING AND GROUTING EPOXY; ANI A118.3: a. CUTOM BUILDING PRODUCT FUION PRO INGLE COMPONENT, HIGH PERFORMANCE GROUT. MEETING THE PERFORMANCE REQUIREMENT OF ANI A118.3 AND A H. ELATOMERIC JOINT CAULK: PROVIDE WHERE INDICATED ON THE DRAWING, AND ELEWHERE A REQUIRED AT ALL JOINT BETWEEN FLOOR AND WALL AND AT JOINT BETWEEN TILE AND DIIMILAR MATERIAL. 1. CUTOM BUILDING PRODUCT COMMERCIAL 100 PERCENT ILICONE CAULK. CONFORM TO ATM C 920 FOR MOVEMENT JOINT IN HEAVY TRAFFIC AREA AND ATM C ACOUTICAL PANEL CEILING PART 1 - GENERAL 1.1 RELATED DOCUMENT DRAWING AND GENERAL CONDITION OF CONTRACT, INCLUDING GENERAL AND UPPLEMENTARY CONDITION AND DIVIION-1 PECIFICATION ECTION APPLY TO WORK OF THI ECTION. DIVIION 9 - FINIHE (CONT'D) 1.2 UMMARY A. ECTION INCLUDE: 1. ACOUTICAL CEILING PANEL. 2. EXPOED GRID UPENION YTEM. 3. WIRE HANGER, FATENER, MAIN RUNNER, CRO TEE, AND WALL ANGLE MOLDING. B. RELATED ECTION: 1. ECTION (01450) - CODE 2. ECTION (01450) - CODE-REQUIRED PECIAL INPECTION AND PROCEDURE 3. ECTION (09250) - PLATER AND GYPUM BOARD 4. DIVIION 23 (15) - HVAC 5. DIVIION 26 (16) ECTION - ELECTRICAL WORK C. ALTERNATE 1. PRIOR APPROVAL: UNLE OTHERWIE PROVIDED FOR IN THE CONTRACT DOCUMENT, PROPOED PRODUCT UBTITUTION MAY BE UBMITTED NO LATER THAN TEN (10) WORKING DAY PRIOR TO THE DATE ETABLIHED FOR RECEIPT OF BID. ACCEPTABILITY OF A PROPOED UBTITUTION I CONTINGENT UPON THE ARCHITECT' REVIEW OF THE PROPOAL FOR ACCEPTABILITY AND APPROVED PRODUCT WILL BE ET FORTH BY THE ADDENDA. IF INCLUDED IN A BID ARE UBTITUTE PRODUCT WHICH HAVE NOT BEEN APPROVED BY ADDENDA, THE PECIFIED PRODUCT HALL BE PROVIDED WITHOUT ADDITIONAL COMPENATION. 2. UBMITTAL WHICH DO NOT PROVIDE ADEQUATE DATA FOR THE PRODUCT EVALUATION WILL NOT BE CONIDERED. THE PROPOED UBTITUTION MUT MEET ALL REQUIREMENT OF THI ECTION, INCLUDING BUT NOT NECEARILY LIMITED TO, THE FOLLOWING: INGLE OURCE MATERIAL UPPLIER (IF PECIFIED IN ECTION 1.5); UNDERWRITER' LABORATORIE CLAIFIED ACOUTICAL PERFORMANCE; PANEL DEIGN, IZE, COMPOITION, COLOR, AND FINIH; UPENION YTEM COMPONENT PROFILE AND IZE; COMPLIANCE WITH THE REFERENCED TANDARD. 1.3 REFERENCE A. AMERICAN OCIETY FOR TETING AND MATERIAL (ATM): 1. ATM A 1008 TANDARD PECIFICATION FOR TEEL, HEET, COLD ROLLED, CARBON, TRUCTURAL, HIGH-TRENGTH LOW-ALLOY AND HIGH-TRENGTH LOW-ALLOY WITH IMPROVED FORMABILITY. 2. ATM A 641 TANDARD PECIFICATION FOR ZINC-COATED (GALVANIZED) CARBON TEEL WIRE. 3. ATM A 653 TANDARD PECIFICATION FOR TEEL HEET, ZINC-COATED (GALVANIZED) BY THE HOT-DIP PROCE. 4. ATM C 423 OUND ABORPTION AND OUND ABORPTION COEFFICIENT BY THE REVERBERATION ROOM METHOD. 5. ATM C 635 TANDARD PECIFICATION FOR METAL UPENION YTEM FOR ACOUTICAL TILE AND LAY-IN PANEL CEILING. 6. ATM C 636 RECOMMENDED PRACTICE FOR INTALLATION OF METAL CEILING UPENION YTEM FOR ACOUTICAL TILE AND LAY-IN PANEL. 7. ATM E 84 TANDARD TET METHOD FOR URFACE BURNING CHARACTERITIC OF BUILDING MATERIAL. 8. ATM E 1414 TANDARD TET METHOD FOR AIRBORNE OUND ATTENUATION BETWEEN ROOM HARING A COMMON CEILING PLENUM. 9. ATM E 1111 TANDARD TET METHOD FOR MEAURING THE INTERZONE ATTENUATION OF CEILING YTEM. 10. ATM E 1264 CLAIFICATION FOR ACOUTICAL CEILING PRODUCT. 11. ATM E 1477 TANDARD TET METHOD FOR LUMINOU REFLECTANCE FACTOR OF ACOUTICAL MATERIAL BY UE OF INTEGRATING-PHERE REFLECTOMETER. 12. ATM D 3273 TANDARD TET METHOD FOR REITANCE TO GROWTH OF MOLD ON THE URFACE OF INTERIOR COATING IN AN ENVIRONMENTAL CHAMBER. 13. ATM E TANDARD TET METHOD FOR FIRE TET OF BUILDING CONTRUCTION AND MATERIAL. B. AHRAE TANDARD , "VENTILATION FOR ACCEPTABLE INDOOR AIR QUALITY" C. INTERNATIONAL CODE COUNCIL-EVALUATION ERVICE - AC 156 ACCEPTANCE CRITERIA FOR EIMIC QUALIFICATION TETING OF NON-TRUCTURAL COMPONENT D. INTERNATIONAL CODE COUNCIL-EVALUATION ERVICE - EVALUATION REPORT, ER-1308, FIRE- AND NONFIRE-REITANCE-RATED UPENDED CEILING FRAMING YTEM E. ACE 7 TANDARD - AMERICAN OCIETY OF CIVIL ENGINEER, MINIMUM DEIGN LOAD FOR BUILDING AND OTHER TRUCTURE F. CICA EIMIC ZONE 3 & 4 - CEILING AND INTERIOR YTEM CONTRUCTION AOCIATION GUIDELINE FOR EIMIC RETRAINT FOR DIRECT HUNG UPENDED CEILING AEMBLIE 1. YTEM DECRIPTION a. EIMIC LOAD: DEIGN AND IZE COMPONENT TO WITHTAND EIMIC LOAD IN ACCORDANCE WITH THE INTERNATIONAL BUILDING CODE, ECTION 1621 FOR CATEGORY D,E, AND F. 1.5 UBMITTAL A. PRODUCT DATA: UBMIT MANUFACTURER' TECHNICAL DATA FOR EACH TYPE OF ACOUTICAL CEILING UNIT AND UPENION YTEM REQUIRED. B. AMPLE: MINIMUM 6 INCH X 6 INCH AMPLE OF PECIFIED ACOUTICAL PANEL; 8 INCH LONG AMPLE OF EXPOED WALL MOLDING AND UPENION YTEM, INCLUDING MAIN RUNNER AND 4 FOOT CRO TEE. C. HOP DRAWING: LAYOUT AND DETAIL OF ACOUTICAL CEILING. HOW LOCATION OF ITEM WHICH ARE TO BE COORDINATED WITH, OR UPPORTED BY THE CEILING. D. CERTIFICATION: MANUFACTURER' CERTIFICATION THAT PRODUCT COMPLY WITH PECIFIED REQUIREMENT, INCLUDING LABORATORY REPORT HOWING COMPLIANCE WITH PECIFIED TET AND TANDARD. FOR ACOUTICAL PERFORMANCE, EACH CARTON OF MATERIAL MUT CARRY AN APPROVED INDEPENDENT LABORATORY CLAIFICATION OF NRC, CAC, AND AC. E. IF THE MATERIAL UPPLIED BY THE ACOUTICAL UBCONTRACTOR DOE NOT HAVE AN UNDERWRITER' LABORATORY CLAIFICATION OF ACOUTICAL PERFORMANCE ON EVERY CARTON, UBCONTRACTOR HALL BE REQUIRED TO END MATERIAL FROM EVERY PRODUCTION RUN APPEARING ON THE JOB TO AN INDEPENDENT OR NVLAP APPROVED LABORATORY FOR TETING, AT THE ARCHITECT' OR OWNER' DICRETION. ALL PRODUCT NOT CONFORMING TO MANUFACTURER' CURRENT PUBLIHED VALUE MUT BE REMOVED, DIPOED OF AND REPLACED WITH COMPLYING PRODUCT AT THE EXPENE OF THE CONTRACTOR PERFORMING THE WORK. 1.6 QUALITY AURANCE A. INGLE-OURCE REPONIBILITY: PROVIDE ACOUTICAL PANEL UNIT AND GRID COMPONENT BY A INGLE MANUFACTURER. B. FIRE PERFORMANCE CHARACTERITIC: IDENTIFY ACOUTICAL CEILING COMPONENT WITH APPROPRIATE MARKING OF APPLICABLE TETING AND INPECTING ORGANIZATION. 1. URFACE BURNING CHARACTERITIC: A FOLLOW, TETED PER ATM E 84 AND COMPLYING WITH ATM E 1264 FOR CLA A PRODUCT. a. FLAME PREAD: 25 OR LE b. MOKE DEVELOPED: 50 OR LE C. EIMIC PERFORMANCE: PROVIDE ACOUTICAL CEILING YTEM THAT HA BEEN EVALUATED BY AN INDEPENDENT PARTY AND FOUND TO BE COMPLIANT WITH THE 2003 INTERNATIONAL BUILDING CODE, EIMIC CATEGORY D, E, AND F. 1. TETED PER INTERNATIONAL CODE COUNCIL - EVALUATION ERVICE - AC 156 ACCEPTANCE CRITERIA FOR EIMIC QUALIFICATION TETING OF NON-TRUCTURAL COMPONENT A EVIDENCED BY INTERNATIONAL CODE COUNCIL EVALUATION REPORT, ER D. HANDLE ACOUTICAL CEILING UNIT CAREFULLY TO AVOID CHIPPING EDGE OR DAMAGED UNIT IN ANY WAY. 1.7 DELIVERY, TORAGE, AND HANDLING A. DELIVER ACOUTICAL CEILING UNIT TO PROJECT ITE IN ORIGINAL, UNOPENED PACKAGE AND TORE THEM IN A FULLY ENCLOED PACE WHERE THEY WILL BE PROTECTED AGAINT DAMAGE FROM MOITURE, DIRECT UNLIGHT, URFACE CONTAMINATION, AND OTHER CAUE. B. BEFORE INTALLING ACOUTICAL CEILING UNIT, PERMIT THEM TO REACH ROOM TEMPERATURE AND A TABILIZED MOITURE CONTENT. C. HANDLE ACOUTICAL CEILING UNIT CAREFULLY TO AVOID CHIPPING EDGE OR DAMAGED UNIT IN ANY WAY. DIVIION 9 - FINIHE (CONT'D) 1.8 PROJECT CONDITION A. PACE ENCLOURE: ALL CEILING PRODUCT AND UPENION YTEM MUT BE INTALLED AND MAINTAINED IN ACCORDANCE WITH ARMTRONG WRITTEN INTALLATION INTRUCTION FOR THAT PRODUCT IN EFFECT AT THE TIME OF INTALLATION AND BET INDUTRY PRACTICE. PRIOR TO INTALLATION, THE CEILING PRODUCT MUT BE KEPT CLEAN AND DRY, IN AN ENVIRONMENT THAT I BETWEEN 32 F (0 C) AND 120 F (49 C) AND NOT UBJECT TO ABNORMAL CONDITION. ABNORMAL CONDITION INCLUDE EXPOURE TO CHEMICAL FUME, VIBRATION, MOITURE FROM CONDITION UCH A BUILDING LEAK OR CONDENATION, EXCEIVE HUMIDITY, OR EXCEIVE DIRT OR DUT BUILDUP. TANDARD CEILING: DO NOT INTALL INTERIOR CEILING UNTIL PACE I ENCLOED AND WEATHERPROOF; WET WORK IN PLACE I COMPLETED AND NOMINALLY DRY; WORK ABOVE CEILING I COMPLETE; AND AMBIENT CONDITION OF TEMPERATURE AND HUMIDITY ARE CONTINUOULY MAINTAINED AT VALUE NEAR THOE INTENDED FOR FINAL OCCUPANCY. BUILDING AREA TO RECEIVE CEILING HALL BE FREE OF CONTRUCTION DUT AND DEBRI. 1.9 WARRANTY A. ACOUTICAL PANEL: UBMIT A WRITTEN WARRANTY EXECUTED BY THE MANUFACTURER, AGREEING TO REPAIR OR REPLACE ACOUTICAL PANEL THAT FAIL WITHIN THE WARRANTY PERIOD. FAILURE INCLUDE, BUT ARE NOT LIMITED TO: 1. ACOUTICAL PANEL: AGGING AND WARPING A A REULT OF DEFECT IN MATERIAL OR FACTORY WORKMANHIP. 2. GRID YTEM: RUTING AND MANUFACTURER' DEFECT 3. ACOUTICAL PANEL WITH BIOBLOCK PLU OR DEIGNATED A INHERENTLY REITIVE TO THE GROWTH OF MICRO-ORGANIM INTALLED WITH ARMTRONG UPENION YTEM: VIIBLE AG AND WILL REIT THE GROWTH OF MOLD/ MILDEW AND GRAM POITIVE AND GRAM NEGATIVE ODOR AND TAIN CAUING BACTERIA. B. WARRANTY PERIOD: 1. ACOUTICAL PANEL: ONE (1) YEAR FROM DATE OF UBTANTIAL COMPLETION. 2. GRID: TEN YEAR FROM DATE OF UBTANTIAL COMPLETION. C. THE WARRANTY HALL NOT DEPRIVE THE OWNER OF OTHER RIGHT THE OWNER MAY HAVE UNDER OTHER PROVIION OF THE CONTRACT DOCUMENT AND WILL BE IN ADDITION TO AND RUN CONCURRENT WITH OTHER WARRANTIE MADE BY THE CONTRACTOR UNDER THE REQUIREMENT OF THE CONTRACT DOCUMENT MAINTENANCE A. EXTRA MATERIAL: DELIVER EXTRA MATERIAL TO OWNER. FURNIH EXTRA MATERIAL DECRIBED BELOW THAT MATCH PRODUCT INTALLED. PACKAGED WITH PROTECTIVE COVERING FOR TORAGE AND IDENTIFIED WITH APPROPRIATE LABEL. 1. ACOUTICAL CEILING UNIT: FURNIH QUALITY OF FULL-IZE UNIT EQUAL TO 5.0 PERCENT OF AMOUNT INTALLED. 2. EXPOED UPENION YTEM COMPONENT: FURNIH QUANTITY OF EACH EXPOED UPENION COMPONENT EQUAL TO 2.0 PERCENT OF AMOUNT INTALLED. PART 2-PRODUCT 2.1 MANUFACTURER A. CEILING PANEL: 1. ARMTRONG WORLD INDUTRIE, INC. CHELEA CLARK (213) CRCLARK@ARMTRONGCEILING.COM, MATCH TILE & GRID ACOUTICAL CEILING UNIT A. ACOUTICAL PANEL TYPE: MATCH 1. URFACE TEXTURE: MATCH 2. COMPOITION: MATCH 3. COLOR: MATCH 4. IZE: 24 IN X 24 IN, MATCH 5. EDGE PROFILE: MATCH 6. NOIE REDUCTION COEFFICIENT (NRC): ATM C 423; CLAIFIED WITH UL LABEL ON PRODUCT CARTON CEILING ATTENUATION CLA (CAC): ATM C 1414; CLAIFIED WITH UL LABEL ON PRODUCT CARTON ABIN: N/A 9. ARTICULATION CLA (AC): N/A 10. FLAME PREAD: ATM E 1264; CLA A (UL) 11. LIGHT REFLECTANCE (LR) WHITE PANEL: ATM E 1477; DIMENIONAL TABILITY: HUMIGUARD PLU 13. RECYCLE CONTENT: POT-CONUMER - 1% PRE-CONUMER - 43% 14. MATERIAL INGREDIENT TRANPARENCY: HEALTH PRODUCT DECLARATION (HPD); DECLARE LABEL 15. LIFE CYCLE AEMENT: THIRD PARTY CERTIFIED ENVIRONMENT PRODUCT DECLARATION (EPD) 16. ACCEPTABLE PRODUCT: CANYON, NO ADDED FORMALDEHYDE A MANUFACTURED BY ARMTRONG WORLD INDUTRIE PART 3 - EXECUTION 3.1 EXAMINATION A. DO NOT PROCEED WITH INTALLATION UNTIL ALL WET WORK UCH A CONCRETE, TERRAZZO, PLATERING AND PAINTING HA BEEN COMPLETED AND THOROUGHLY DRIED OUT, UNLE EXPRELY PERMITTED BY MANUFACTURER' PRINTED RECOMMENDATION. (EXCEPTION: HUMIGUARD MAX CEILING) 3.2 PREPARATION A. MEAURE EACH CEILING AREA AND ETABLIH LAYOUT OF ACOUTICAL UNIT TO BALANCE BORDER WIDTH AT OPPOITE EDGE OF EACH CEILING. AVOID UE OF LE THAN HALF WIDTH UNIT AT BORDER, AND COMPLY WITH REFLECTED CEILING PLAN. COORDINATE PANEL LAYOUT WITH MECHANICAL AND ELECTRICAL FIXTURE. B. COORDINATION: FURNIH LAYOUT FOR PREET INERT, CLIP, AND OTHER CEILING ANCHOR WHOE INTALLATION I PECIFIED IN OTHER ECTION. 1. FURNIH CONCRETE INERT AND IMILAR DEVICE TO OTHER TRADE FOR INTALLATION WELL IN ADVANCE OF TIME NEEDED FOR COORDINATION OF OTHER WORK. 3.3 INTALLATION (CATEGORY D,E,F) A. INTALL UPENION YTEM AND PANEL IN ACCORDANCE WITH THE INTERNATIONAL BUILDING CODE, ECTION 1621, EXCEPT A NOTED IN ECTION OF ER-1308, AND WITH THE AUTHORITIE HAVING JURIDICTION. B. ER-1308, ECTION , ALTERNATE EIMIC DEIGN CATEGORY D,E AND F INTALLATION: UNDER THI INTALLATION, THE RUNNER MUT BE RATED HEAVY-DUTY AND HAVE A MINIMUM IMPLE PAN UNIFORM LOAD OF POUND PER LINEAL FOOT (238 N/M); MAXIMUM CEILING WEIGHT PERMITTED I 4.0 POUND PER QUARE FOOT (19.5 KG/M2). 1. THE BERC-2 CLIP I UED TO ECURE THE MAIN RUNNER AND CRO RUNNER ON TWO ADJACENT WALL TO THE TRUCTURE AND THE TWO OPPOITE WALL TO THE PERIMETER TRIM, A DETAILED BELOW. A NOMINAL 7/8-INCH (22 MM) WALL MOLDING I UED IN LIEU OF THE 2-INCH (51 MM) PERIMETER UPPORTING CLOURE ANGLE REQUIRED BY ECTION (B) OF ACE-7 FOR EIMIC DEIGN CATEGORIE D, E AND F. EXCEPT FOR THE UE OF THE BERC-2 CLIP AND THE 7/8-INCH (22 MM) WALL MOLDING AND ELIMINATION OF PREADER BAR, INTALLATION OF THE CEILING YTEM MUT BE A PRECRIBED BY THE APPLICABLE CODE. 2. THE BERC-2 CLIP I ATTACHED TO THE WALL MOLDING BY LIDING THE LOCKING LANCE OVER THE HEM OF THE VERTICAL LEG OF THE WALL MOLDING. CLIP INTALLED ON THE WALL WHERE THE RUNNER ARE FIXED ARE ATTACHED TO THE RUNNER BY A HEET METAL CREW THROUGH THE HORIZONTAL LOT IN THE CLIP INTO THE WEB OF THE RUNNER. ALTERNATE #2: IF ACCEPTABLE TO ARCHITECT, FIXED ATTACHMENT MAY BE ACCOMPLIHED BY POP-RIVETING THE RUNNER TO THE WALL MOLDING. DIVIION 9 - FINIHE (CONT'D) 3. CLIP INTALLED ON THE WALL WHERE THE RUNNER ARE NOT FIXED TO THE RUNNER ALLOW THE TERMINAL RUNNER END TO MOVE 3/4 INCH (19.1 MM) IN BOTH DIRECTION. BERC-2 CLIP INTALLED IN THI MANNER ARE AN ACCEPTABLE MEAN OF PREVENTING RUNNER FROM PREADING IN LIEU OF PACER BAR REQUIRED IN CICA 3-4, WHICH I REFERENCED IN ACE 7, ECTION , WHICH I REFERENCED IN IBC ECTION C. THE JCG EIMIC EPARATION JOINT CLIP I TO BE INTALLED PER THE MANUFACTURER' INTRUCTION, C D. THE JMR15 EIMIC JOINT CLIP MAIN BEAM I TO BE INTALLED PER THE MANUFACTURER' INTRUCTION, C E. THE PREENCE OF A HANGER WIRE WITHIN 3 INCHE OF AN EXPANION RELIEF JOINT A CALLED FOR IN ATM C636 HALL BE REQUIRED IN ADDITION TO THE REQUIREMENT OF THE INTERNATIONAL BUILDING CODE, ECTION AND WITH THE AUTHORITIE HAVING JURIDICTION. 1. ONLY APPLIE WHEN UING PRELUDE XL FIRE GUARD 15/16Ï ½; PRELUDE PLU XL FIRE GUARD 15/16Ï ½; AND UPRAFINE XL FIRE GUARD 9/16Ï ½ EXPOED TEE YTEM. F. FOR REVEAL EDGE PANEL: CUT AND REVEAL OR RABBET EDGE OF CEILING PANEL AT BORDER AREA AND VERTICAL URFACE. G. INTALL ACOUTICAL PANEL IN COORDINATION WITH UPENDED YTEM, WITH EDGE RETING ON FLANGE OF MAIN RUNNER AND CRO TEE. CUT AND FIT PANEL NEATLY AGAINT ABUTTING URFACE. UPPORT EDGE BY WALL MOLDING. 3.4 FIELD QUALITY CONTROL A. UPENDED CEILING HALL BE UBJECT TO THE PECIAL INPECTION REQUIREMENT IN ECTION (01450) - CODE-REQUIRED PECIAL INPECTION AND PROCEDURE. 3.5 ADJUTING AND CLEANING A. REPLACE DAMAGED AND BROKEN PANEL. B. CLEAN EXPOED URFACE OF ACOUTICAL CEILING, INCLUDING TRIM, EDGE MOLDING, AND UPENION MEMBER. COMPLY WITH MANUFACTURER' INTRUCTION FOR CLEANING AND TOUCH UP OF MINOR FINIH DAMAGE. 1. CEILING TOUCH-UP PAINT, (ITEM #5760, 8OZ. BOTTLE) (ITEM #5761, QUART IZE CAN), "GLOBAL WHITE" LATEX PAINT HOULD BE UED TO HIDE MINOR CRATCHE AND NICK IN THE URFACE AND TO COVER FIELD TEGULARIZED EDGE THAT ARE EXPOED TO VIEW. C. REMOVE AND REPLACE WORK THAT CANNOT BE UCCEFULLY CLEANED AND REPAIRED TO PERMANENTLY ELIMINATE EVIDENCE OF DAMAGE. DIVIION 10 - PECIALTIE DIVIION 11 - EQUIPMENT DIVIION 12 - FURNIHING DIVIION 13 - PECIAL CONTRUCTION DIVIION 14 - CONVEYING YTEM DIVIION DIVIION 21 - FIRE UPPREION DEIGN BUILD BY FIRE PRINKLER UBCONTRACTOR DIVIION 22 - PLUMBING DIVIION 23 - HVAC EE MECHANICAL DRAWING DIVIION 24 AND 25 DIVIION 26 - ELECTRICAL EE ELECTRICAL DRAWING DIVIION 27 - COMMUNICATION DIVIION 28 - ELECTRONIC AFETY AND ECURITY DIVIION 29 AND 30 DIVIION 31 - EARTHWORK DIVIION 32 - EXTERIOR IMPROVEMENT DIVIION 33 - UTILITIE DIVIION 34-49, PECIFICATION G

5 DEMOLITION GENERAL CONDITION 1. THEE DRAWING ARE INDICATION OF CONTRUCTION AND ARE DIAGRAMMATIC. EXACT LOCATION, IZE, EXTENT AND CONDITION OR CONTRUCTION TO BE REMOVED, RELOCATED, OR TO REMAIN HALL BE VERIFIED AT THE ITE BY THE CONTRACTOR. 2. COORDINATE ALL WORK WITH THAT HOWN IN TRUCTURAL, MECHANICAL, PLUMBING AND ELECTRICAL DRAWING. 3. PROTECT FLOOR, TRUCTURE, AND FINIHE CHEDULED TO REMAIN DURING DEMOLITION AND CONTRUCTION. 4. THE CONTRACTOR HALL NOTIFY THE ARCHITECT IMMEDIATELY OF ANY DICREPANCY ON THE DRAWING OR THE UNCOVERING OF ANY HIDDEN CONDITION THAT AFFECT THE NEW CONTRUCTION. 5. THE CONTRACTOR HALL CONFORM TO ALL PROCEDURE A ETABLIHED BY THE APPLICABLE BUILDING CODE AND MUNICIPAL REQUIRED. 6. CONTRUCTION, EQUIPMENT, AND MATERIAL INDICATED TO BE REMOVED HALL BE REMOVED COMPLETE FOR THAT ITEM, INCLUDING FRAMING, UPPORT, ANCHOR, FATENER, AND FINIHE FOR A MAKE-READY CONDITION FOR NEW CONTRUCTION, EXCEPT A OTHERWIE NOTED. 7. DEMOLITION HALL BE UFFICIENT TO COMPLETE THE NEW WORK HOWN IN THE DOCUMENT. CONTRACTOR HALL NEATLY CUT AND REMOVE FINIHE A REQUIRED TO A NATURAL POINT OF DIVIION TO ENABLE INTALLATION OF BLOCKING, BACKING, FRAMING, HEATHING, UTILITIE, OR OTHER CONCEALED WORK, WHETHER PECIFICALLY HOWN OR INFERRED FOR NEW WORK. REFER TO OTHER DRAWING FOR CONCEALED WORK. 8. REMOVE ALL WALL FINIHE TO TUD UNLE OTHERWIE NOTED. REMOVE ALL PROTRUDING CREW, NAIL, ETC. A REQUIRED FOR NEW WORK. 9. REMOVE ALL EXPOED CONDUIT, BOXE, AND FIRE ALARM COMPONENT. EE ELECTRICAL DRAWING FOR ADDITIONAL INFORMATION AND NEW WORK. 10. REMOVE ALL FIXTURE, DEVICE, PLUMBING AND MECHANICAL DEVICE COMPLETELY, UNLE NOTED OTHERWIE. 11. DO NOT CUT, REMOVE, OR ALTER ANY TRUCTURAL MEMBER OR PORTION OF THE FLOOR YTEM UNLE PECIFICALLY NOTED OR HOWN. NOTIFY ARCHITECT IMMEDIATELY OF ANY UNTABLE OR UN-UNRECORDED TRUCTURAL MEMBER. DO NOT PROCEED WITH WORK IN THE AREA UNTIL DIRECTED TO DO O BY THE ARCHITECT. 12. INPECT EXPOED TRUCTURE FOR DAMAGE AND ADVIE ARCHITECT., WHERE LAB CUTTING OCCUR, COORDINATE AND MINIMIZE ALL LAB CUTTING TO THAT NECEARY TO COMPLETE THE WORK HOWN IN THE TRUCTURAL, ELECTRICAL, PLUMBING, AND MECHANICAL DRAWING. 14. THE CONTRACTOR HALL NOT CAUE OR IMPOE ANY IMPACT LOAD OR EXCEIVE VIBRATION DURING DEMOLITION. MATERIAL HALL NOT BE PILED, TACKED, OR ALLOWED TO ACCUMULATE IN A MANNER THAT WOULD EXCEED THE AFE LOAD LIMIT OF THE TRUCTURE. 15. HORING I THE REPONIBILITY OF THE CONTRACTOR. 16. DUT CONTROL HALL BE IMPLEMENTED DURING DEMOLITION. TILE FLOOR TO REMAIN REMOVE CEILING ABOVE FOR NEW ROOM 17. KEEP JOBITE WEATHER TIGHT DURING DEMOLITION. 18. PATCH AND PREPARE URFACE OF FINIHE ON WALL AND CEILING CHEDULED TO REMAIN. 19. REMOVE ALL MATERIAL REULTING FROM DEMOLITION. ALL AREA HALL BE BROOM CLEANED UPON COMPLETION OF THE DEMOLITION WORK. COACH 20. ALL HAZARDOU MATERIAL RELATED IUE HOULD BE REVIEWED WITH OWNER AND HAZARDOU MATERIAL ABATEMENT CONULTANT PRIOR TO COMMENCEMENT OF DEMOLITION. 21. ALL HAZARDOU MATERIAL TO BE REMOVED BY OTHER PRIOR TO THE TART OF THE PROJECT. REMOVE AND RELOCATE LOCKER REMOVE DOOR AND FRAME, ALAVGE FOR REUE REMOVE CARPET AND BAE IN THI ROOM, PREPARE LAB FOR REPLACEMENT CARPET TELEVIION AND BRACKET TO BE REMOVED (HATCHED AREA NOT IN COPE) REMOVE ET OF DRINKING FOUNTAIN, PREPARE WALL FOR NEW DRINKING FOUNTAIN WITH BUILT IN BOTTLE FILLER (ALTERNATE #1) 22. HAZARDOU MATERIAL ABATEMENT WILL NOT TART UNTIL APPROVAL FROM THE AHJ. 23. ALL PLUMBING TACK ABANDONED TO REMAIN AND TO BE CAPPED. 24. ITEM TO BE ALVAGED HALL BE REMOVED BY CONTRACTOR AND AFELY TORED FOR REUE. COORDINATE WITH OWNER AND ARCHITECT. WALL TYPE LEGEND WALL TO REMAIN BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras REMOVE PORTION OF WALL FOR RELOCATED DOOR REMOVE GYP BOARD FURRING THI IDE OF THE COLUMN PREPARE LAB UNDERNEATH LOCKER FOR RUBBER FLOORING (BAE BID) REMOVE FLOORING/BAE AND PREPARE LAB FOR NEW RUBBER FLOORING THROUGHOUT LOCKER ROOM (ALTERNATE #4) DEMOLITION PLAN n o r t h REMOVE GYP. A NEEDED TO INTALL BACKING/NEW TUD FOR COUNTER REMOVE BOOTH AND ALL ELECTRONIC EQUIPMENT REMOVE CARPET AND BAE, PREPARE LAB FOR NEW CARPET AND RUBBER FLOOR FINIH (EE FINIH PLAN) REMOVE AND ALVAGE INK FOR REUE, BAE AND UPPER CABINET (ALTERNATE #1) PREPARE LAB FOR NEW RUBBER FLOORING THROUGHOUT LOCKER ROOM (ALTERNATE #3) TELEVIION AND BRACKET TO BE REMOVED, ALVAGE TO OWNER REMOVE LIGHT FIXTURE IN () AND ALVAGE FOR FUTURE REUE, EE RCP AND ALTERNATE #2 FOR REPLACEMENT LIGHT FIXTURE IT CABINET TO BE REMOVED, IT EQUIPMENT TO BE RELOCATED WALL TO BE REMOVED DEMOLITION PLAN A

6 3'-0" A1 2" -1B 2'-6" 2'-0" CUT UPPORT EDGE 45 DEGREE CONC. FLOOR LAB 2'-0" WALL TYPE LEGEND WALL TO REMAIN WALL TO BE REMOVED OUND BATT INULATION PROVIDE BACKING UPPORT A ALL EDGE CHEDULED BAE BUILT-IN COUNTER DETAIL ATTACH UPPORT ANGLE TO PLYWOOD WITH 3/4" LONG #8 6" OC 2 1/2" X 2 1/2" X 1/4" TEEL ANGLE OC AND AT EACH COUNTER END CREW UPPORT TO 12 GA TUD W/ 1/4" DIAMETER 6" OC ADD 12 GA TUD NEXT TO TUD AND AT EACH ANGLE UPPORT TUD. ATTACH WITH (2) #8 8" OC, TAGGERED CALE: 1" = NEW WALL, ALL WALL TO BE TYPE 'A', UNO. EE WALL TYPE ON A2 GENERAL NOTE EQ. EQ. EQ. EQ. -1B A1 A101 A. PATCH/REPAIR ALL GYP WHERE BACKING/BLOCKING AND UTILITIE ARE ADDED/RELOCATED. 3" 3'-0" ROOM - EAT A3 LINE OF DOOR WING 3'-0" EQ. EQ. 6'-0" NEW OFOI 75"-80" MONITOR & BRACKET. GC TO PROVIDE BACKING, POWER & DATA INFILL DOOR, PATCH TO MATCH ADJACENT ROOM - WET LINE OF OFFIT MILLWORK (NO CHANGE) NEW HEADER AT OPENING A4 PILATER ALUMINUM TOREFRONT WINDOW 1/4" GLAZING, MATCH PT-2 "EDUCATION I THE TEPPING TONE TO UCCE!" - JOE ANTETT 4'-0" ROOM - NORTH 3'-6" 4'-0" NEW VINYL DECAL GRAPHIC, CFCI. QUOTED TEXT TO BE 5" HIGH LETTER, FINAL GRAPHIC TO BE APPROVED BY CLIENT, OPEN TO BEYOND 7'-0" 8'-10" RELOCATED LOCKER PROVIDE BAE/BACKING UPPORT A NEEDED 2'-2" EQ EQ B3 LOUNGE - NORTH ELEVATION A102 A1 A2 LINE OF OFFIT ABOVE NEW MONITOR OFOI, GC TO PROVIDE BACKING, POWER AND DATA INFILL DOOR OPENING TO MATCH A3 12'-4" A4 A101 A2 NEW BUILT-IN COUNTER A1 A101 (HATCHED AREA NOT IN COPE) NEW CFCI TELEVIION & BRACKET. GC TO PROVIDE BACKING, POWER & DATA, EE ELEC. (e) FOR ALTERNATE #1 CHANGE TO BREAK ROOM, REFER TO HEET A EQ. EQ. BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/9/18; 10:56 AM; Edrick Ferreras FLOOR PLAN NEW BROOM CLOET, MILLWORK TO MATCH NEW GYP BOARD ATTACHED TO FURRING CHANNEL ATTACHED TO COLUMN. PAINT AND TEXTURE TO MATCH ADJACENT. CONTRACTOR TO NOTIFY ARCHITECT IMMEDIATELY IF REQUIRED R.O. FOR DOOR CANNOT BE ACHIEVED n o r t h 2'-0" VIF WITH IT UPPLIER ALIGN RELOCATED IT EQUIPMENT, PROVIDE EQUIPMENT RACK AND MILLWORK DOOR NEW 7'-0" AFF NEW TELEVIION, EE ELEC. (e) ALIGN 4'-0" D4 B3 A101 C3 ALIGN A D3 ALIGN NEW WALL WITH OFFIT ABOVE NEW TELEVIION, EE ELEC. C3 6'-0" EG-1 LOUNGE - OUTH ELEVATION NEW CUTOM GRAPHIC, CFCI PILATER EQ. 6'-0" EQ. NEW CFCI TELEVIION & BRACKET. GC TO PROVIDE BACKING, POWER & DATA, EE ELEC. D3 LOUNGE - EAT ELEVATION D4 PL-1B LOUNGE - WET ELEVATION NEW MILLWORK DOOR FOR RELOCATED IT EQUIPMENT, HANDLE TO MATCH IN BREAK ROOM (A), MAGNETIC LATCH FLOOR PLAN A

7 A1 WET WALL OF ROOM TO REMAIN COACH LOCKER ROOM 45 MAX 2" MIN. 12'-0" TYP. 45 MAX 12'-0" TYP. 6'-0" MAX 45 MAX 45 MAX MAIN RUNNER CRO RUNNER LINE OF WALL 12 GA. VERTICAL 4'-0" O.C. RIGID TRUT AT PLAY WIRE LOCATION IF REQ'D HALL COMPLY WITH ALL GOVERNING CODE. 12 GA. PLAY 12" O.C. IN THE PLANE OF EACH RUNNER CRO RUNNER MAIN RUNNER TYPICAL ACOUTICAL CEILING TILE LAYOUT NEW 2X2 REPLACEMENT TILE WHERE CEILING I CUT NEW 2X2 CELING GRID IN (), MATCH PRODUCT AND TYLE EIMIC HANGER WIRE PLAYED 45D FROM MAIN RUNNER IN EACH DIRECTION AND 45D FROM CRO RUNNER IN EACH DIRECTION 12'-0" O.C. EACH WAY & 6'-0" FROM WALL VERTICAL HANGER 4'-0" O.C. EACH WAY & 8" FROM WALL 2"TYP TRUT CHEDULE EMT IZE (NOMINAL) LENGTH (L/r < 200) 1/2" < 3'-10" 3/4" < 5'-0" 1" < 6'-6" 1 1/4" < 8'-6" 1 1/2" < 9'-10" EMT - ELECTRICAL METALLIC TUBING NEW MANUALLY OPERATED ROLLER HADE WITH CUTOM GRAPHIC. MFR TO BE MECHOHADE OR APPROVED EQUAL, UNLV TO PROVIDE GRAPHIC/LOGO 45 MAX 45 MAX 45 MAX 45 MAX IF HANGER MUT BE PLAYED MORE THAN 1- IN-6 OUT OF PLUMB, PROVIDE COUNTER LOPED HANGER EMT CONDUIT TRUT FATENED TO MAIN RUNNER AND EXTENDED TO AND FATENED TO TRUCTURAL MEMBER UPPORTING THE ROOF OR FLOOR ABOVE, IF REQ'D BY LOCAL JURIDICTION. LOCATE ALL EIMIC HANGER WIRE. EE CHEDULE FOR TRUT IZE. LOT CONDUIT END TO FIT OVER CEILING RUNNER AND ATTACH W/ #10 ELF-TAPPING CREW DO NOT BEND WIRE AROUND INTERFERING EQUIPMENT. PROVIDE TWO 1 1/2" CHANNEL TRAPEZE NOTE: 1. PROVIDE HEAVY DUTY GRID YTEM A REQUIRED PER EIMIC ZONE 'D' 1. HANGER WIRE MUT BE NO. 12 GA. MIN. OFT- ANNEALED, MILD TEEL WIRE. WIRE HALL BE WRAPPED TIGHTLY AT RUNNER AND UPPORT AND TIED WITH A MIN. OF 3 TURN. 2. CLIP HALL HOLD RUNNER TIGHTLY TOGETHER. PLICE CLIP HALL BE CAPABLE OF REITING AT LEAT 50 LB. IN TENION OR COMPREION. 3. FOR MANUFACTURED YTEM, UBMIT UBTANTIATION IN ACCORDANCE WITH THE GOVERNING CODE. 4. RUNNER HALL BE CAPABLE OF UPPORTING CEILING YTEM WITH DEFLECTION LE THAN INCH. 5. LOCAL KINK AND BEND HALL NOT BE MADE IN HANGER WIRE FOR LEVELING. 6. HALL COMPLY WITH ALL GOVERNING CODE, ATM C 635 & ATM C 636, A WELL A CICA REQUIREMENT. NOT TO CALE REFLECTED CEILING PLAN GENERAL NOTE A. CENTER ALL GRID IN ROOM U.N.O. B. CENTER ALL LIGHT IN CEILING TILE U.N.O. C. CENTER ALL FIRE PRINKLER IN CEILING TILE U.N.O. D. PAINT ALL EXPOED DUCTWORK, TRUCTURE, CONDUIT, AND DEVICE. E. PAINT ALL MECHANICAL DEVICE IN GYP. BD. CEILING TO MATCH CEILING. F. CONTRACTOR TO VERIFY / CONFIRM (E) LOCATION OF (E) AUTOMATIC FIRE PRINKLER YTEM PIPING AND (E) HVAC PIPE OR DUCT PRIOR TO TART CONTRUCTION. IF ANY CONFLICT /DICREPANCIE BETWEEN THE DRAWING AND THE ACTUAL CONDITION ARE DICOVERED, THE CONTRACTOR HALL ADVIE THE ARCHITECT AND REQUET A CLARIFICATION. G. EE ELECTRICAL DRAWING FOR HORN, PEAKER, PULL TATION, LIGHT FIXTURE AND OTHER FEATURE NOT OTHERWIE HOWN. H. EE ELECTRICAL DRAWING FOR EXIT IGN & EMERGENCY LIGHTING CONDITION. J. EE MECHANICAL DRAWING FOR PIPING, REGITER, AND VENT NOT OTHERWIE HOWN. MECHANICAL DUCT LOCATION DIMENION ARE NOMINAL. VERIFY IN FIELD TO MAINTAIN CLEARANCE TO FIXED ELEMENT. END CEILING LEGEND (e) UPENDED ACOUTIC TILE TO REMAIN UPENDED GYPUM BOARD CEILING, PAINTED. UPEND WITH ARMTRONG DRYWALL/TUCCO/PLATER GRID YTEM 2' x 2' LIGHT FIXTURE TO BE RELOCATED NEW UPPLY, EE MECH. DWG. NEW 15/16" DIFFUING LEN T-BAR LED LIGHT FIXTURE BY JLC-TECH (FOR ALTERNATE #2 LIGHT FIXTURE, REFER TO D3/A) NEW 2' x 2' KYTRIM LIGHT FIXTURE IN FIXTURE LOCATION RELOCATED NEW NOT A PART, LINE OF WD-1 OFFIT EQ. 9'-1 1/2" (e) VIF C L C L C L (e) (e) A1 A102 (e) (e) EQ. LINE OF NEW OFFIT, FACE TO BE WD-1,MATCH CEILING TRIM AT NEW WALL TO MATCH (e) (e) (e) (HATCHED AREA NOT IN COPE) WD-1 NEW ALIGN WITH TOP NEW MILLWORK BROOM CLOET, WOOD FINIH TO MATCH, FLUH WITH ADJACENT RELOCATED LOCKER (HOWN HATCHED) BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras REFLECTED CEILING PLAN n o r t h REMOVE (E) LIGHT FIXTURE NEW GYP. BOARD OFFIT WITH WOOD PANEL FACE AND BOTTOM (WD-1), WHERE LOCKER HAVE BEEN RELOCATED PATCH CEILING WHERE COLUMN FURRING HA BEEN REPLACED GYP. BOARD MILLWORK DOOR AND RELOCATED IT EQUIPMENT (e) (e) (e) 7'-0" GYP. BD. HEADER ALIGN NEW WALL WITH FACE OF OFFIT A REPAINT CEILING/ OFFIT PT-2 FOR ALTERNATE #2 LIGHT FIXTURE, REFER TO /A C4 D4 - EAT NEW GYP. BOARD OFFIT RELOCATED LOCKER WD-1 AT FACE OF NEW OFFIT WD-1 (NEW WOOD PANEL UNDER GYP. BOARD OFFIT - OUTH NEW HANDLE TO MATCH LOCKER TO REMAIN WD-1 REFLECTED CEILING PLAN A

8 NO. A ROOM NAME ID C LVT-1B PL-1B PT-2 RF-1 RF-2 EG-1-1A -1B WD-1 WT-1B FLOOR C C C MATERIAL TYPE CARPET LUXURY VINYL TILE LAMINATE PAINT PAINT RUBBER BAE RUBBER FLOORING RUBBER FLOORING ILICONE EDGE GRAPHIC OLID URFACE OLID URFACE WOOD WALL TILE GENERAL MATERIAL NOTE: BAE NORTH ROOM FINIH CHEDULE WALL CEILING EAT OUTH WET MANUFACTURER INTERFACE HAW CONTRACT FORMICA DUNN EDWARD DUNN EDWARD MANNINGTON MONDO MONDO TECHTONIC AMUNG AMUNG CERAMIC TECHNIC TYLE NAME/# DETOUR UNVEIL/0601V GRAY RED TARON TARON - PT-2 INTERIOR COLOR AND MATERIAL LEGEND COLOR NAME/#/PATTERN ONYX/ TARNIH/01585/AHLAR FOLKTONE HEX/6473/ COLD MORNING/DE6365/ COVERED IN PLATINUM/DE6367/ IRON/908 / MEDIUM GRAY/W69/PUNTI-3MM RED/H70/HARMONI-3MM ANDED BIRCH/B412/ UNIVER/U053/ TONEWORK INDUTRIAL REFLECTION - WHITE COMMENT WALL FINIH AT ALL EXPOED GYPUM BOARD. PATCH WITH NEW "RF-2" RUBBER FLOORING ACCENT WHERE LOCKER ARE REMOVED (BAE BID). PROVIDE NEW "RF-1" RUBBER FLOORING THOUGHOUT LOCKER AREA, (ALTERNATE #4), EE PLAN FOR PAINT FINIH PATCH WITH NEW "RF-2" RUBBER FLOORING ACCENT WHERE CARPET I REMOVED (BAE BID). PROVIDE NEW FINIHE THRUOUT (ALTERNATE #1). PROVIDE NEW "RF-1" RUBBER FLOORING THOUGHOUT, (ALTERNATE #3). COMMENT TYPICAL BUILDING TANDARD CARPET 9"X36" TILE, ALTERNATE #1 - EE NOTE BELOW ALTERNATE #1 MATCH MATCH COLOR, UE TRAIGHT BAE ALTERNATE #3 & #4, EE NOTE BELOW EE NOTE BELOW 14'-0" X 4'-5" CUTOM FRAME, GRAPHIC TO BE PROVIDED BY OWNER ALTERNATE #1 NEW COUNTER IN (), BAE BUILD MATCH WOOD FINIH ON LOCKER & OFFIT 4"X8" TILE WITH 1/8" MAPEI AVALANCHE GROUT, ALTERNATE #1 PREPARE AND CLEAN CONCRETE LAB URFACE AND INTALL A REQUIRED BY MFR INTRUCTION. INTALLER TO BE A COMPANY PECIALIZING IN PERFORMING THI WORK WITH A MINIMUM OF 5 YEAR DOCUMENTED EXPERIENCE. PROVIDE PRODUCT DATA AND (2) VERIFICATION AMPLE, MIN. 6" QUARE OF ACTUAL PRODUCT COLOR & PATTERN., PT-2 C TILE FLOOR TO REMAIN PT-2 C RF-2 (HATCHED AREA NOT IN COPE) RUBBER FLOOR TO REMAIN. (ALTERNATE #3, REFINIH FLOOR IN ENTIRE BREAK ROOM, REFER TO HEET A) BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/9/18; 10:57 AM; Edrick Ferreras RUBBER FLOOR TO REMAIN. (ALTERNATE #4, REFINIH FLOOR IN ENTIRE AREA, REFER TO HEET A) FINIH FLOOR PLAN n o r t h D3 A103 D3 A103 IM C A RF-2 D3 MIN. DOOR (WHERE OCCUR) CARPET A CHEDULED RUBBER FLOORING UNDERLAY TOPPED WITH THINET TO FORM MOOTH TRANITION TO CARPET, OVERLAY WITH RUBBER FLOORING A CHEDULED RUBBER FLOORING TO CARPET TRANITION CALE: 3" = FT-01 FINIH FLOOR PLAN & DETAIL A

9 18" L X 6" W 12 GA. HEET METAL 24" O.C. WITH (4) X 1" HILTI HOT PIN (1) #10 CREW INTO EACH LEG OF TUD DETAIL 0 1/2" CLEAR PACE (3) #10 CREW (TOP TRACK TO PLATE) 18 GA. UNPUNCHED TRACK 2 1/2" DEEP LEG LOTTED 1 1/2" = HEIGHT UP TO 12'-0" UP TO 18'-0" BRACE LENGTH 6'-0" OR UNDER 6'-1" TO 8'-0" METAL TUD IZE AND PACING 24" O.C. 24" O.C. BRACE IZE NOTE: 1. TUD BRACED BY GYPUM WALL BOARD EACH IDE. MAXIMUM CREW PACING HALL NOT EXCEED 12" O.C PF MAX. LATERAL LOAD 3. Fy (MIN.) = 33 KI 4. L/120 DEFLECTION LIMIT 5. EE FINIH CHEDULE AND/OR INTERIOR ELEVATION FOR ALL FINIHE 6. TO HEAR WALL. 7. EE ARCHITECTURAL REQUIREMENT FOR RATED WALL. METAL TUD BOX BEAM HEADER CONTINUOU EALANT, BOTH IDE HIM, A REQUIRED DOOR NO. LOCATION W 3'-0" 3'-0" 3'-0" H 7'-0" 7'-0" 7'-0" A B B TYPE DOOR FINIH HARDWARE TYPE DOOR CHEDULE FRAME MATERIAL -- FINIH U.L. RATING RELOCATED DOOR GENERAL NOTE: 1. CONTRACTOR TO UE THE ARCHITECT' DOOR TYPE PLAN DEIGNATION NUMBER IN ADDITION TO THE ROOM NUMBER ON ALL HOP DRAWING CHEDULE UBMITTAL. 2. ALL DOOR IN MEAN POF EGRE YTEM TO BE OPERABLE FROM INIDE WITHOUT UE OF KEY OR PECIAL KNOWLEDGE OR EFFORT. 3. THE MAXIMUM EFFORT TO OPERATE DOOR CANNOT EXCEED 8.5 POUND FOR EXTERIOR DOOR, AND 5.0 POUND FOR INTERIOR DOOR. 4. THE BOTTOM 10" ON THE PUH IDE OF THE DOOR HALL HAVE A MOOTH UNINTERRUPTED URFACE THAT ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOTRET WITHOUT CREATING A TRAP OR HAZARDOU CONDITION. 5. COORDINATE ALL KEYING REQUIREMENT WITH OWNER. 6. DOOR THICKNE HALL BE 1 3/4" - U.N.O. 7. DOOR HALL MATCH, COLOR TO MATCH ADJACENT DOOR. 8. ALL DOOR FRAME HALL BE "TIMELY" HOLLOW METAL FRAME - PAINTED U.N.O. 9. PROVIDE BLOCKING FOR ANY IN-WALL ACCEORIE, UCH A WALL-MOUNTED DOOR TOP. NOTE: 1. DOOR NUMBER: THE DOOR NUMBER IN THE CHEDULE CORREPOND WITH THE NUMBER OF THE ROOM OF WHICH THE DOOR I LOCATED. PLU THE LETTER UFFIX INDICATED ON THE PLAN FOR THAT DOOR, REFER ALO TO THE FLOOR PLAN AND THE INTERIOR AND EXTERIOR ELEVATION. 2. OPENING IZE I EQUAL TO NET OPENING. ROUGH OPENING I EQUAL TO OPENING IZE AND FRAME DIMENION. 3. ALL EXTERIOR DOOR HALL BE WEATHER TRIPPED. 4. ALL DOOR HALL BE PROVIDED WITH A LEVEL FLOOR OR LANDING. ALL THREHOLD PROVIDED HALL HAVE A MAXIMUM OF 1/2" ABOVE THE FLOOR OR LANDING PER CODE. 5. EXCEPT FOR LIDING DOOR, THE LOWER 12" OF ALL DOOR HALL COMPLY WITH CODE AND HALL BE MOOTH AND UNINTERRUPTED, TO ALLOW THE DOOR TO BE OPENED BY A WHEELCHAIR FOOT RET, WITHOUT CREATING A TRAP OR HAZARDOU CONDITION. 6. THE MAXIMUM EFFORT TO OPERATE DOOR, APPLIED AT RIGHT ANGLE TO HINGED DOOR OR AT THE CENTER PLANE LIDING DOOR HALL COMPLY WITH THE LATET CODE REQUIREMENT. 7. UNLE NOTED OTHERWIE: DOOR OPENING IN RATED WALL HALL BE PROTECTED BY A TIGHT FITTING MOKE AND DRAFT CONTROL AEMBLY HAVING A FIRE PROTECTION RATING IF NOT LE THAN (20) MINUTE. THE LABELED AEMBLY HALL BE ELF CLOING OR AUTOMATIC CLOING ACTUATION OF A MOKE DETECTOR AND HALL BE PROVIDED WITH A CONTINUOU GAKET ALONG THE TOP AT THE DOOR JAMB AND HEAD. 8. ALL INTERIOR WOOD DOOR HALL BE FINIHED A CHEDULED. 9. CONTRACTOR TO VERIFY DOOR FRAME WIDTH REQUIRED AT WALL, WHICH VARY IN THICKNE. DOOR HARDWARE NOTE: ALL HARDWARE TO BE LEVER TYPE PER IBC AND ICC/ANI REQUIREMENT. FINIH EQ. TO BRUHED ALUMINUM. HARDWARE TO MEET REQUIREMENT OF IBC ECTION AND ICC/ANI A ECTION MOUNTING HEIGHT HALL BE BETWEEN 34" AND 48". LEVER TYLE TO BE PA - VIF, MATCH ADJACENT DOOR HARDWARE ET OPTION: HW ET 01 - RELOCATED DOOR - VERIFY PECIFIED LOCK WILL FIT IN PREP For use on mark/door #(s): Provide each GL door(s) with the following: Qty Description Catalog Number Finish Mfr 3 EA HINGE 5BB1 4.5 X IVE 1 EA CLAROOM LOCK ND70BD PA 626 CH 1 EA FIC PERM CORE KEYMARK-BY UNLV LOCK HOP 626 MED 1 EA KICK PLATE " X 2" LDW B-C 630 IVE 1 EA WALL TOP W406/407CCV 630 IVE 3 EA ILENCER R64 GRY IVE HW ET 03 For use on mark/door #(s): Provide each GL door(s) with the following: Qty Description Catalog Number Finish Mfr 3 EA HINGE 5BB1 4.5 X IVE 1 EA PUH PLATE " X 16" 626 IVE 1 EA PULL PLATE " 4" X 16" 630 IVE 1 EA URFACE CLOER 4040XP HEDA 689 LCN 1 EA KICK PLATE " X 2" LDW B-C 630 IVE 1 EA WALL TOP W406/407CCV 630 IVE 3 EA ILENCER R64 GRY IVE HW ET 02 For use on mark/door #(s): REMARK Provide each GL door(s) with the following: Qty Description Catalog Number Finish Mfr 3 EA HINGE 5BB1 4.5 X IVE 1 EA ENTRANCE LOCK ND53BD PA 626 CH 1 EA FIC PERM CORE KEYMARK-BY UNLV LOCK HOP 626 MED 1 EA KICK PLATE " X 2" LDW B-C 630 IVE 1 EA WALL TOP W406/407CCV 630 IV 3 EA ILENCER R64 GRY IVE, ALUMINUM TOREFRONT YTEM TRUCTURAL MEMBER ABOVE 1/4" GLAZING (1) #8 CREW PER TUD TYPICAL CONNECTION EACH FLANGE OF TUD TO TEEL TRAP (TOP & BOTTOM TRACK) A HEAD BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/6/18; 12:17 PM; Edrick Ferreras A WALL TYPE 18 GA. UNPUNCHED TRACK 2 1/2" DEEP LEG LOTTED CEILING - EE REFLECTED CEILING PLAN NOTE: CRIBE TUD / GYPUM BOARD TO THE DECK / JOIT A REQUIRED. WALL HEATHED BOTH IDE FULL HEIGHT WITH GYP. BD. PER CURRENT CODE. TAPE/FLOAT/TEXTURE/ PAINT. PROVIDE 5 / 8 " GREEN BOARD ON ALL WET WALL. METAL TUD (EE CHEDULE) R-13 BATT 3 5/8" TUD, R-19 BATT 6" TUD CONTINUOU 20 GA. UNPUNCHED TRACK (1 5/16"" MIN. FLANGE) WITH HILTI POWDER ACTUATED FATENER X-U DIA WITH MIN. 1" 32" O.C. OR EQUAL (ICC ER-2269) (1) #8 CREW PER TUD TYPICAL CONNECTION EACH FLANGE OF TUD TO TEEL TRAP (TOP & BOTTOM TRACK) CONCRETE LAB 1/2" = B C 5/8" GYP BOARD BATT INULATION WHERE OCCUR 5/8" GYP BOARD JAMB 5/8" GYP BOARD ILL CONTINUOU EALANT AND BACKER ROD BOTH IDE ALUMINUM FRAMED TOREFRONT HIM A REQUIRED ALUMINUM TOREFRONT FRAME BEYOND ALUMINUM FRAMED TOREFRONT INT. TOREFRONT WINDOW (MTL TUD) CALE: 3" = DW-08 BATT INULATION A OCCUR, EE WALL TYPE 5/8" GYPUM BOARD OVER METAL TUD. EE PLAN AND WALL TYPE FOR IZE A B HEAD 5/8" GYPUM BOARD OVER METAL TUD. EE PLAN AND WALL TYPE FOR IZE BATT INULATION A OCCUR, EE WALL TYPE JAMB METAL TUD BOX BEAM HEADER, 3 5/8" TUD FOR OPENING 60" OR LE, 6" TUD FOR LARGER OPENING CONTINUOU EALANT BOTH IDE CHEDULE DOOR FRAME, PAINTED CHEDULE DOOR CONTINUOU EALANT BOTH IDE CHEDULE DOOR, EE CHEDULE JAMB ANCHOR, PROVIDE 3 PER IDE CHEDULE DOOR FRAME, PAINTED INTERIOR HM DOOR (MTL TUD) CALE: 3" = DOOR TYPE NOT TO CALE A WELDED HOLLOW METAL (MATCH ) B WELDED HOLLOW METAL WITH VIION LIGHT (MATCH ) DOOR CHEDULE, WINDOW CHEDULE & DETAIL

10 A1 NEW REFRIGERATOR AND FREEZER, PROVIDE POWER REPLACE DRINKING FOUNTAIN WITH NEW UNIT WITH INTEGRAL BOTTLE FILLER LINE OF PILATER ATTACH TOE KICK TO FULL-HEIGHT BAE CABINET DOOR 12" DEEP UPPER CABINET WITH (2) ADJUTABLE HELVE AND WHITE MELAMINE INTERIOR FINIH, TYP. WT-1B PL-1B -1A PL-1B 24" DEEP LOWER CABINET WITH (1) ADJUTABLE HELF AND WHITE MELAMINE INTERIOR FINIH, TYP. BREAK ROOM - NORTH ALTERNATE #1 LINE OF PILATER OPEN TO BEYOND ALTERNATE 1. REMODEL BREAK ROOM (A). NEW CAEWORK, KITCHEN EQUIPMENT, AND FINIHE, EE DRAWING ON A. 2. NEW LIGHTING FIXTURE (T-BAR LIGHTING) THROUGHOUT (), EE REFLECTED CEILING PLAN ON A, ZONED WITH (2) TWO DIMMABLE WITCHE. 3. FULLY REPLACE RUBBER FLOORING IN BREAK ROOM (A). 4. FULLY REPLACE RUBBER FLOORING IN COACHE LOCKER ROOM ()., B1 BREAK ROOM - OUTH ALTERNATE #1 12" DEEP UPPER CABINET WITH (2) ADJUTABLE HELVE AND WHITE MELAMINE INTERIOR FINIH, TYP. NEW MICROWAVE, PROVIDE POWER PL-1B LINE OF PILATER PROTECT IN PLACE TRANITION TRIP WT-1B -1A RF-1 PL-1B RF-1 A C1 24" DEEP LOWER CABINET WITH (1) ADJUTABLE HELF AND WHITE MELAMINE INTERIOR FINIH, TYP. BREAK ROOM - EAT ALTERNATE #1 C2 D3 A103 BREAK ROOM ALTERNATE #3 C3 ROOM ALTERNATE #4 BIM erver: bimserver.aptusgroup.com - BIM erver 21/ ; 4/9/18; 10:58 AM; Edrick Ferreras WALL TYPE LEGEND D1 4'-0" LVT-1B WALL TO REMAIN WALL TO BE REMOVED NEW WALL, ALL WALL TO BE TYPE 'A', UNO. EE WALL TYPE ON OUND BATT INULATION (HATCHED AREA NOT IN COPE) REPLACE DRINKING FOUNTAIN WITH NEW UNIT WITH INTEGRAL BOTTLE FILLER R 4'-8" 7'-1 1/2" F A NEW REFRIGERATOR AND FREEZER, CFCI - MFR TO BE TRUE, MODEL # GDM-19T-HC~TL01 (REFRIGERATOR) & GDM-19T-F-LD (FREEZER). CONTRACTOR TO PROVIDE POWER A1 B1 C1 NEW MECHANICAL, ELECTRICAL AND PLUMBING IN THI ALTERNATE TO BE DEIGN BUILD BY CONTRACTOR FLOOR PLAN ALTERNATE #1 5'-10" VIF 8" ø OLID URFACE GROMMET WITH TRAH CAN BELOW - CFCI INK TO BE REUED NEW MICROWAVE, CFCI - CONTRACTOR TO PROVIDE POWER GENERAL NOTE D D NOTE: ELECTRICAL IN THI ALTERNATE TO BE DEIGN BUILD BY CONTRACTOR REFLECTED CEILING PLAN ALTERNATE #2 CEILING LEGEND (e) UPENDED ACOUTIC TILE TO REMAIN UPENDED GYPUM BOARD CEILING, PAINTED. UPEND WITH ARMTRONG DRYWALL/TUCCO/PLATER GRID YTEM 2' x 2' LIGHT FIXTURE TO BE RELOCATED NEW UPPLY, EE MECH. DWG. NEW 15/16" DIFFUING LEN T-BAR LED LIGHT FIXTURE BY JLC-TECH (FOR ALTERNATE #2 LIGHT FIXTURE, REFER TO D3/A) NEW 2' x 2' KYTRIM LIGHT FIXTURE IN FIXTURE LOCATION RELOCATED NEW NOT A PART NOTE: FOR RCP GENERAL NOTE EE HEET A102 ALTERNATE A

11 P No A RO FE Exp MECHANICAL EVAD N I O N A L ROBERT P. FINNEGAN APR MECHANICAL COVER HEET MP000 7 F O ATE EN G - T INEE R FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

12 A P No A RO FE Exp MECHANICAL EVAD N I O N A L ROBERT P. FINNEGAN APR MECHANICAL AND PLUMBING PLAN MP101 7 F O ATE EN G - T INEE R FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

13 ELECTRICAL COVER HEET E FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

14 ELECTRICAL PECIFICATION E FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

15 D A C.2 D D.1 D.2 E D D A D D D C.2 D D.1 D.2 E LIGHTING CEILING PLAN E FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

16 A A POWER PLAN E FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154

17 ELECTRICAL INGLE LINE DIAGRAM AND CHEDULE E FEA C O N U L T I N G E N G I N E E R W W W. F E A L A V E G A. C O M 2821 W. HORIZON RIDGE PKWY. UITE 200 H E N D E R O N, N E V A D A P F copyright 2018 by aptus 1200 outh 4th treet, 89154