DILLARD'S INC TEST PROTOCOL FOR DILL USA- (V38) SPECIAL CLAIMS

Transcription

1 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 1 of 7 SCOPE: This protocol predominantly applies to fabric, garment and accessories that include claims with special function in products. Test only the darkest color for each test within this protocol. NLYTICL ntibacterial activity assessment on textile TCC / CPSD-N [nti-bacterial] Shall be no growth for the product with "anti-microbial" and/or "anti-bacterial" claim only. Note: Test on original state and after 5 washes. ssessment of antibacterial finishes on textile ntifungal activity assessment on textile TCC / CPSD-N TCC Test 3 / CPSD- N PHYSICL CHRCTERISTICS Fur-Doc Microscopic / BV testing / CPSD-GB PERFORMNCE Water wicking CPSD-SL Water vapor transmission of materials Drying Time DIDS-GB treated 1 untreated Client requirement [nti-bacterial] Report actual result in percent (%) reduction for the product with "antimicrobial" and/ or "anti-bacterial" claim only. Testing on both 'treated' and 'untreated' fabric/garment samples. Note: Test on original state and after 5 washes. Client requirement 1 [nti-bacterial] Shall be no growth for the product with "anti-microbial" and/ or "Mold/ fungus inhibitor" claim only. Client requirement -- [dditional claims] Verification if applicable. Document review. 1 [Moisture management] [If claimed "Wicks way Moisture" or similar] 7.5 cm (minimum) at 30 minutes. (Original state, after 5X launderings and 10X launderings) STM E [Moisture management] [Original, after 5X launderings and 10X launderings] 500 g/m² 24 hours 3 [Moisture management] 20% retained moisture after 30 minutes (Original, after 5X launderings and 10X launderings)

2 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 2 of 7 R bsorbency of textiles Soil release: oily stain release Water repellency: spray test Water repellency: spray test rain test hydrostatic pressure test ppearance of textile end products after repeated home laundering Wrinkle recovery of fabrics: appearance TCC [Moisture management] [Test only the side facing the skin] [Original, after 5X launderings and 10X launderings] Maximum 30 seconds. TCC [Stain release claims] Original : Grade 4.0 minimum fter 5 washes (Per care instructions): Grade 3.5 minimum TCC [If stain resistance / stain repellency / stain release claims] Original: ISO 90 minimum fter 5 wash (Per care instruction): ISO 70 minimum. TCC [Nano tex products / Coolest comfort] Original: ISO 100 minimum 5 Washes: ISO 90 minimum 30 Washes: ISO 70 minimum. TCC [Nano tex products/coolest comfort] Less than 1 gram penetration after 2 minutes at 600 mm. TCC [Nano tex products / coolest comfort] 25 psi minimum. TCC [Nano tex products / coolest comfort] Evaluate after 5 and 10 home launderings as per client requirement including, the seams, fabric and creases evaluations to meet the claim. Evaluations to be made on the following: 100% Cotton and CVC blends / Synthetic and Blends Wrinkle free / Wrinkle resistant Smoothness: Grade 4.0 minimum Seams: Grade 4.0 minimum Pleats / Creases: Grade 4.0 minimum Easy care Smoothness: Grade 3.5 minimum Seams: Grade 3.5 minimum Pleats / Creases: Grade 3.5 minimum. TCC [Nano tex products / coolest confort] [Original and fter 3 Launderings] Grade 3.5 minimum Oil repellency TCC [Nano tex products / coolest comfort] Original: Grade 6.0 minimum

3 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 3 of 7 Soil release test CPSD-SL rain test hydrostatic pressure test ppearance of textile end products after repeated home laundering Wrinkle recovery of fabrics: appearance Durability of flocking Resistance to puncture 5 washes: Grade 5.0 minimum 30 washes: Grade 4.0 minimum. 1 [Nano tex products / coolest comfort] Report original and after 5 launderings (Per care instructions) Stain to used: Ketchup, mustard, grape juice and kool aid Original: Grade 4.0 minimum fter 5 washes (Per care instructions): Grade 3.5 minimum. TCC [Water claims] [If claimed water resistant] Less than 1 gram penetration after 2 minutes at 600 mm. TCC [Water claims] [If claimed waterproof] 25 psi minimum. TCC [Durable press/wrinkle free/easy care claims] [DP] Evaluate after 5 and 10 home launderings as per client requirement including, the seams, fabric and creases evaluations to meet the claim. Evaluations to be made on the following: 100% Cotton and CVC blends / Synthetic and Blends Wrinkle free / Wrinkle resistant Smoothness: Grade 4.0 minimum Seams: Grade 4.0 minimum Pleats / Creases: Grade 4.0 minimum Easy care Smoothness: Grade 3.5 minimum Seams: Grade 3.5 minimum Pleats / Creases: Grade 3.5 minimum. TCC [Durable press/wrinkle free claims] [Original and fter 3 Launderings] Grade 3.5 minimum. CPSD-SL STM F (R2013)e1 1 [dditional claims] Compare original and after 3 washes, wash according to care instructions No obvious defects/observations affecting the end performance/appearance, color change/ staining, satisfactory performance of the components and trims. 1 [dditional claims] 5 lb minimum

4 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 4 of 7 brasion STM D resistance of (R2017) fabric: rotary platform, doublehead ir permeability STM D R2016 Snagging resistance of fabrics: mace Oven mitt and pot holder temperature 1 [dditional claims] No surface changes after 300 cycles Use: CS17 abradant & 500 g. Head weight. 1 [dditional claims] 10 cfm maximum STM D [dditional claims] Minimum Grade 4.0 for 600 revolutions. CPSD-HL [Heat resistance products] [If heat resistant coating is present] No melting or burning should occur up to 3 minutes and a maximum rise of temperature up to 160 F within 30 seconds is considered safe. gradient Oil repellency TCC [If stain resistance / stain repellency / stain release claims] Report original and after 5 laundering (per care instructions) Original: Grade 6.0 minimum fter 5 washes: Grade 4.0 minimum. Impact resistance of plastic sewthrough buttons Button center strength STM D [Super durable button] (67 mm height) Test all garments. 10 if submitted loosely. CPSD-SL No fractures, cracks or chipping. Maximum 10 % breakage allowed. - [Super durable button] Ligne size: (Light duty) < lb 20 to lb 26 to lb > lb Ligne Size: (Heavy duty) < lb 20 to lb 26 to lb > lb Soil release test CPSD-SL [If stain resistance / stain repellency / stain release claims] Report original and after 5 launderings (Per care instructions)

5 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 5 of 7 Ultraviolet protection factor (UPF) Waist Band Stretch and Recovery COLORFSTNESS Colorfastness to ozone OTHERS content filling power turbidity cleanliness fat & oil STM D / TCC / STM D (Mod) STM D R2015 (Mod) Stain to used: Ketchup, mustard, grape juice and kool aid Original: Grade 4.0 minimum fter 5 washes (Per care instructions): Grade 3.5 minimum. [If claimed UPF] Perform on "original" and "after simulated use and care" samples. For simulated use and care, need to prepare the sample as per STM D6544 The UPF rating shall be given as per STM Method D6603 as below: 15-24: Good UV protection 25-39: Very good UV protection : Excellent UV Protection Modification: Wash only to 20 washes [If Claim TEKFIT] Using Instron: elongate 2, record force required to maintain 2 elongation Using Wall Mounted Stretch and Recovery Rack pply load recorded from Instron and maintain for 60 minutes Measure recovery immediately (Data only) llow to relax for 1 hour Remeasure recovery: Waistband growth 0.5 inch (maximum) Test before and after 5 machine wash TCC [On denim fabric and any fabric using indigo dye only] Grade 4.0 minimum (1 cycle). STM D R2012/IDFB part 3 s specified (for labeling, follow the US( D) Textile Labeling Guidelines for Feather and Down) 2-3% tolerance. IDFB Part 10-B [Steam conditioning] s claimed: ± 5% minimum If no claim is made,report value only. IDFB Part mm minimum (U.S. measurement) IDFB part 4/JIS 6.3/EN 1163 Hypo-allergenic / Super clean claims: 500 mm minimum. 0.7% minimum - 2.0% maximum.

6 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 6 of 7 IDFB part 7/JIS 6.6/EN 1162/STM D R2012 oxygen number odor evaluation downproofness - tumbling IDFB / BV In house - FD 001 FTMS 191- Method 5530 (Mod) ir permeability STM D R2016 Less than 10 Hypo-allergenic / Super clean claims: < 5 No putrid condition Grade 4.0 minimum. 1 [dditional claims] Downproof: 5 cfm maximum. NOTE ON SMPLE SELECTION: Dillard's Testing Protocol addresses "Representative Sampling" by requiring every style to be tested at least once per Season. Further, When Selecting Style to be sent for Testing, the Vendor/Factory Quality representative should randomly select finished products which have been fully produced in the Factory ssembly lines and comply with all supplied( or authorized by Dillard's) Style and BOM specifications. No. Of Required for Complete Testing No. Of (Fully Packed) Cartons For Transit Testing: No. Of Working Days For Complete Testing: - 5 Client pproval: Creation Date: Last Revision Date: Pricing Review Date Lucy Feng 21/Dec/ /ug/ /Dec/2017 Technical Review Date: Key M R dditional Charge For This Test Mandatory Regulatory

7 DILLRD'S INC TEST PROTOCOL FOR DILL US- (V38) SPECIL CLIMS By/Date: Page 7 of 7 Result Key C R M NM N NT Claimed Recorded Meets Does Not Meet Not pplicable Not Tested Rating Key PSS FIL NR Pass Fail Not Requested