The National BIM Library

Transcription

1 The National BIM Library BIM Object Guide: Platon Plaster Base Version rd December Version rd December 2012 Page 1 of 9

2 Table of Contents 1.0 Introduction Naming Parameters National BIM Library Parameters Manufacturers Parameters IFC Parameters COBie Parameters Abbreviations... 9 Version rd December 2012 Page 2 of 9

3 1.0 Introduction This guide covers the use of Triton Systems Platon Plaster Base included within the National BIM Library. Triton Systems Platon Plaster Base All products listed below are included in the following file: nbl_mbrn_tritonsystems_platonplasterbase nbl_tritonsystems_platonplasterbase Version rd December 2012 Page 3 of 9

4 1.1 Naming National BIM Library objects are named to identify their type and configuration. Fields are segregated using an under bar (_) and information within each field is segregated using hyphens (-). Fields are abbreviated to reduce characters and capitals used at the start of each abbreviation to aid readability. File name and objects are named as below: File name Field1 Author_Field2 Category_Field3 Manufacturer_Field4 Product Range Object Field1 Author_Field2 Manufacturer_Field3 Product Version rd December 2012 Page 4 of 9

5 2.0 Parameters Parameters included in all National BIM Library Triton Systems Platon Plaster Base BIM object are as follows: 2.1 National BIM Library Parameters Author BIMObjectName Description Help IssueDate Manufacturer URL NBSDescription NBSReference Version Authors Name. Name of the BIM object as it will appear in Software. Using NBL naming procedure. The full description of a product or system. National BIM Library website. The date the object goes live. Manufacturer s main website link. NBS Uniclass title. NBS Uniclass section/clause number. The version number of the object. Version rd December 2012 Page 5 of 9

6 2.2 Manufacturers Parameters WaterDrainageCapacity StudHeight MaterialThickness Weight SofteningTemperature The maximum amount of water the object can effectively drain. Measured in units of [L/m per second at 2% slope.] The product stud height. Measured in [mm] Thickness of the material from which the object is constructed. The relative mass or the quantity of matter contained by it, giving rise to a downward force; the heaviness of an object. Measured in units of [g/m²]. Temperature or range of temperatures at which a substance softens. Measured in [ C] 2.3 IFC Parameters Note: IFC definitions have been obtained from BuildingSmart IFC2x3 website ( Material Main material of the covering Version rd December 2012 Page 6 of 9

7 2.4 COBie Parameters The following COBie parameters have been included within Triton Systems Platon Plaster Base BIM objects and can be used to prepare COBie data schedules: AccessibilityPerformance AssetIdentifier BarCode CodePerformance Colour Constituents Cost Documentation DocumentReference Features Finish Grade InstallationDate Accessibility issue(s) which the product satisfies. The asset identifier assigned to an occurrence of a product (prior to handover). The identity of the bar code (or rfid) given to an occurrence of the product. Code Compliance requirement(s) which the product satisfies. Characteristic or primary colour of product. Optional constituent features, parts or finishes. Cost impact of replacement process. Location (Uniform Resource Information) for further product information. Location (Uniform Resource Information) for the source or updates to this product information. Other important characteristics or features relevant to product specification. Characteristic or primary finish of product. Standard grading which the product corresponds. The date that the manufactured item was installed. LifeCyclePhase Life Cycle Phase as defined in ISO Manufacturer MethodOfMeasurement ModelLabel ModelReference The organization that manufactured or assembled the item. Method of measurement The model number assigned by manufacturer. The name used by the manufacturer Version rd December 2012 Page 7 of 9

8 NominalHeight NominalLength NominalWidth Process ProductionYear ReferenceStandard ReplacementCost SerialNumber ServiceLifeDuration ServiceLifeType Shape Size Typically the vertical or secondary characteristic dimension. Typically the larger or primary horizontal dimension. Typically the characteristic or secondary horizontal or characteristic dimension. Specification of process The year of production of the manufactured item. Reference standard(s) to which the product is compliant. An indicative cost for unit replacement. The serial number assigned to an occurrence of a product by the manufacturer. The service life that an artefact is expected to have under current operating conditions. The typical service life that is quoted for an artefact under reference operating conditions. Characteristic shape of product. Characteristic size of product. SustainabilityPerformance Sustainability issue(s) which the product satisfies. TagNumber WarrantyDescription WarrantyDurationLabour WarrantyDurationParts WarrantyGuarantorLabour WarrantyGuarantorParts WarrantyStartDate The tag number assigned to an occurrence of a product Description of the warranty. Duration of labour warranty (years). Duration of parts warranty (years). Organization acting as guarantor of labour warranty. Organization acting as guarantor of parts warranty. The date on which the warranty commences. Version rd December 2012 Page 8 of 9

9 3.0 Abbreviations nbl National BIM Library mbrn Membrane Version rd December 2012 Page 9 of 9