SPECIFICATIONS FULL AUTOMATION OF THE MULTIPURPOSE GAMMA IRRADIATION FACILITY
|
|
- Gyles Sherman
- 5 years ago
- Views:
Transcription
1 SPECIFICATIONS FULL AUTOMATION OF THE MULTIPURPOSE GAMMA IRRADIATION FACILITY 1. Scope This Statement of Work (SOW) describes the requirements for equipment and services necessary for the full automation of the multipurpose (hereinafter referred as the System ) of the Philippine Nuclear Research Institute (PNRI) (hereinafter referred as the End-User ). Upon completion, the System shall be continuous, fully automated, 4-pass 2-level tote box irradiator with additional source rack containing 2-modules Background Information The irradiation facility started as a Gammabeam-651 PT irradiator (Nordion Canada) in 1989 with 4 turntables and 8 individually-operated source racks. It was upgraded in 2008 from a batch to a semi-automated, 2-pass 2-level tote box type of irradiator, 3 tote boxes per pass and 14 tote boxes per batch. It has a single source rack containing 4 modules with 40 pencils per module. The tote boxes are manually loaded by pushing these boxes from the storage area to the source pass mechanism and the tote boxes rotate automatically around the source during irradiation. The irradiation facility is located inside the End-User compound. The irradiation cell is located at the ground floor of the building. It is a rectangular room and the irradiator is of wet-storage type. The details of layout of the existing facility building, irradiation cell, pool, roof inserts, source rack and source configuration can be seen in Figures 1 to 6 and Tables 1 to 2. The irradiator is being used for the different applications of radiation processing such as food irradiation, decontamination of cosmetic raw materials, radiation sterilization of medical devices and for R&D Specification of the Existing Irradiation Facility: Batch, semi-automated 2-pass, 2-level tote box irradiator, 3 tote boxes per pass, 14 tote boxes per batch; Single source rack with four modules (with 40 pencils per module). Presently loaded with 45 radioactive pencils; Size of tote box: 70 x 50 x 90 cm (inner dimension); PLC system; and Wet-storage type. 2. Applicable Documents The following documents shall be applicable for this Specification to the extent specified hereinafter: 2.1. Automation of the facility shall strictly follow the relevant international standards provided for in IAEA Safety Guide Radiation Safety of Gamma, Electron and X Ray Irradiation Facilities for protecting people and the environment No. SSG-8, 2010, Specific Safety Guide, latest version. See In the event of conflict between the documents listed above and the content of this Specification, the content of this Specification shall take precedence to the extent of the conflict. Page 1 of 12
2 3. Requirements 3.1. Functional and Performance Requirements The System shall meet the following functional and performance requirements: Conversion to a fully automated conveyer system; Operated in stationary, batch and continuous mode, providing maximum efficiency Technical Requirements The System shall meet the following technical requirements: Fully functional rolling transport system, 2-levels, from storage area to the irradiation cell; Source pass mechanism, four-pass system (2-pass on each side of the source, 2-levels, 4-tote boxes per pass. Total of 34 tote boxes (inner dimension is 70 x 50 x 90 cm, maximum load is 125 kg); Additional source rack containing 2 modules and each module with 40 dummy pencils. This shall be integrated with the existing source rack with 4 modules. The two source racks can be operated independently; Additional source hoist system (pneumatic system); Pneumatic cylinders for source pass mechanism; New PLC control system; Safety interlocks and radiation monitors; Provision of temporary container for Co-60 source; Unloading of existing Co-60 source to the temporary container; Re-loading of existing Co-60 source to the 2 source racks (existing and additional) with the best source configuration to obtain optimum dose distribution; Provide details whether the return of installation tools and temporary container is required. The details of layout of the proposed fully-automated facility and proposed source rack configuration can be seen in Figures 7. to Specific Requirements The Contractor shall provide complete technical procedures, protocols, plans, including fabrication of any necessary infrastructure and/or tools required, radiation budget anticipated for personnel and time schedule for completion of the Work, as required for submission by the End-User to appropriate National Safety Regulatory Authorities for approval The Contractor shall, at the request of IAEA/End-User, ship from origin to the End-User and return installation tools and temporary container. 4. Marking The System shall have all safety markings in English language. 5. Packing The System, for the shipment by air to the End-User, shall be packed in accordance with international standards that are applicable for the shipment by air of this kind of equipment. Page 2 of 12
3 6. Quality requirements The System shall be manufactured, shipped and installed in accordance with the Contractor s ISO quality assurance system or an equivalent quality assurance system; The Contractor shall document the compliance with this quality assurance system. 7. Testing and Acceptance 7.1. The System, prior to shipment, shall be tested for conformance of the System with manufacturer s performance specifications and the minimum requirements specified herein. Conformance certificate or statement shall be supplied prior to on site validation The System, after installation, shall be tested by the Contractor together with the End-User (on site) to demonstrate that the performance meets the manufacturer s performance specifications and the minimum requirements specified herein as determined by the IAEA and the End-User The results of the testing of the System shall be documented by the Contractor in an Acceptance Document that shall be signed and dated by the End-User. 8. Installation and Training 8.1. The Contractor shall install the System at the End-User location; 8.2. The Contractor shall provide minimum five (5) days operation and safety (on-site) training to three (3) End-User technical staff members in the English language. 9. Deliverable Data Items The Contractor shall provide two (2) complete sets in hard copies and one (1) in electronic version in the English language of the following: 9.1. Operating Instructions; 9.2. Preventive Maintenance and Service Manual; 9.3. Technical drawings of the System and Detailed Drawing of the Irradiator; 9.4. Conformance certificate and Acceptance Document as per paragraphs 7.1. and 7.3. respectively; 9.5. Warranty Certificates. 10. Qualification Requirements The Contractor shall work in close cooperation with End-User and the IAEA in all aspects of the Work; The Contractor shall provide evidence of relevant international experience (complete planning, supply and/or rehabilitation of gamma irradiators, supply of control and conveyor systems). A minimum of three (3) such completed relevant jobs must have been performed in the last ten (10) years. Page 3 of 12
4 Figure 1. Floor Plan of the Multipurpose -ground floor (measurement in meter not to scale) Page 4 of 12
5 Figure 2. Floor Plan of Existing Irradiation Cell, with semi-automated, batch, 2-pass, 2-levels tote box system and single source rack (R1) - (measurement in mm not to scale) Page 5 of 12
6 Figure 3. Section of Irradiation Cell showing pool dimension (measurement in meter not to scale) 9 Holes Roof Insert of Source Rack of Gammabeam 651PT Irradiator 3 Holes Roof Insert of the Existing Source Rack of Irradiator Figure 4. Roof Inserts (taken from inside of irradiation cell) Page 6 of 12
7 Figure 5. Structure and Dimension of Existing Source Rack with 4-modules (measurement in mm not to scale) Figure 6. Existing Source Rack - Rack 1 (R1) with 4 modules, 40 pencils per module, with 45 radioactive C-188 Co-60 pencils Page 7 of 12
8 Table 1. Source Loading Report - Modules 1 & 3 (as of February 2009) Page 8 of 12
9 Table 2. Source Loading Report- Modules 2 & 4 (as of February 2009) Page 9 of 12
10 Figure 7. Proposed Floor Plan of Irradiation Cell with fully-automated, continuous, 4-pass, 2-levels tote box system and 2 source racks (R1 and R2) - (measurement in mm not to scale) Figure 8. Proposed Source Pass Mechanism (fully automated continuous, 4-pass, 2-levels tote box system with 4 tote boxes per pass, total of 34 tote boxes) Page 10 of 12
11 Figure 9. Proposed Source Racks: Rack 1 (R1) with 4-modules and Rack 2 (R2) with 2-modules R1: Existing Source Rack (4 modules) R2: Additional Source Rack (2 modules) Figure 10. Proposed Source Rack Configuration (R1 and R2) Page 11 of 12
12 Figure 11. Proposed Rolling Transport System at the Irradiation Cell Figure 12. Proposed Rolling Transport System at the Storage Area) Page 12 of 12
SPECIFICATION. Ir-192 hot cell
SPECIFICATION Ir-192 hot cell 1. Scope The purpose of this document is to define the specifications for the construction of a class C hot cell with two chambers (hereinafter referred as the System ) intended
More informationSPECIFICATION. High Dose Rate Brachytherapy Equipment Package
1. Scope SPECIFICATION High Dose Rate Brachytherapy Equipment Package This specification describes the equipment requirements for a new high dose rate brachytherapy service required at National Cancer
More informationSPECIFICATION. High Dose Rate Brachytherapy Equipment Package
SPECIFICATION High Dose Rate Brachytherapy Equipment Package 1. Scope This specification describes the equipment requirements for a new high dose rate brachytherapy service required at the Hospital General
More informationSPECIFICATION CT SIMULATOR FOR BLACK LION HOSPITAL, ADDIS ABEBA, ETHIOPIA
SPECIFICATION CT SIMULATOR FOR BLACK LION HOSPITAL, ADDIS ABEBA, ETHIOPIA 1. Scope This specification describes the requirements for the supply, delivery, installation, and acceptance testing of a CT Simulator
More informationA Proposed Design for Moveable Mechanical Conveyor System Increases Radiation Safety of Industrial Cobalt-60 Irradiators
Arab Journal of Nuclear Sciences and Applications The Egyptian Society of Nuclear Vol 50, 3, (104-111) 2017 Sciences and Applications ISSN 1110-0451 Web site: esnsa-eg.com A Proposed Design for Moveable
More informationThe Path Ahead. Scientific Forum IAEA General Conference Vienna; 2015 Sept
The Path Ahead Scientific Forum IAEA General Conference Vienna; 2015 Sept. 15 16 Paul Gray; V.P. External Relationships and Global Logistics, Nordion Chairman; International Source Suppliers and Producers
More informationQUALITY AGREEMENT. This Quality Agreement is made between. (Customer Legal Entity Name Hereinafter called CUSTOMER ) And
QUALITY AGREEMENT This Quality Agreement is made between (Customer Legal Entity Name Hereinafter called CUSTOMER ) And (Pall Legal Entity Name Hereinafter called PALL ) 1. Table of Contents 1. Table of
More informationSPECIFICATION DIGITAL MAMMOGRAPHY UNIT AND ASSOCIATED SERVICES
1 Digital Mammography Unit 1. Scope SPECIFICATION DIGITAL MAMMOGRAPHY UNIT AND ASSOCIATED SERVICES This specification describes the requirements for a digital mammography equipment and associated services
More informationSTATEMENT OF WORK. Refurbishment of the cooling system of the Nuclear Research Reactor at the Nuclear Center "Dr. Nabor Carrillo Flores".
STATEMENT OF WORK Refurbishment of the cooling of the Nuclear Research Reactor at the Nuclear Center "Dr. Nabor Carrillo Flores". Page 1 of 8 STATEMENT OF WORK 1. Introduction This Statement of work (SOW)
More informationSection 4. Annex to IAEA Request for Proposal STATEMENT OF WORK. Primary/Secondary cooling water Heat Exchangers
Section 4 Annex to IAEA Request for Proposal 25919 STATEMENT OF WORK Primary/Secondary cooling water Heat Exchangers WWR-SM Research Reactor, UZBEKISTAN Page 1 of 17 1. Scope 1.1 This Statement of Work
More informationSPECIFICATION STATEMENT OF WORK. Performance Specification for a radiotherapy linear accelerator
Specifications / Statement of Work / Terms of Reference SPECIFICATION STATEMENT OF WORK Performance Specification for a radiotherapy linear accelerator 1. Scope These specifications describe the requirements
More informationINDUSTRIAL GAMMA IRRADIATION FACILITY WITH A WET STORAGE SOURCE IN SYRIAN ARAB REPUBLIC
IAEA-SM 350/44 INDUSTRIAL GAMMA IRRADIATION FACILITY WITH A WET STORAGE SOURCE IN SYRIAN ARAB REPUBLIC XA9847746 I. OTHMAN, A. MOUSSA Atomic Energy Commission, Damascus, Syrian Arab Republic D.G. STEPANOV,
More informationOfficial-Mail.Tenders@iaea.org ATTACHMENT 1 TO RFQ NO. 29868-AS - Cooling Water Heat Exchangers for Uzbekistan SPECIAL INSTRUCTIONS TO BIDDERS FOR PREPARATION OF THE PROPOSAL These Special Instructions
More informationScientific Production Company Doza GAMMA RAY IRRADIATION UNIT UPG-P FOR CALIBRATION SERVICES. User Manual FVKM RE
Scientific Production Company Doza GAMMA RAY IRRADIATION UNIT UPG-P FOR CALIBRATION SERVICES User Manual Content 1 Description and operation of the product 3 1.1 Product functionality.. 3 1.2 Technical
More informationTURBO MACH A DIVISION OF VT SAA
TERMS AND CONDITIONS PAGE: 1 OF 5 1. PURPOSE To define specific terms and conditions for the purchase of product, materials and services. 2. SCOPE All products, materials and services purchased for use
More informationSample Vial Secure Container SPECIFICATION. 1. Scope
1. Scope SPECIFICATION Sample Vial Secure International Atomic Energy Agency (IAEA) inspectors must maintain continuity of knowledge on all safeguard samples and, in particular, on those samples drawn
More information317 DECREE. of the State Office for Nuclear Safety of 13 June 2002,
317 DECREE of the State Office for Nuclear Safety of 13 June 2002, On type-approval of packagings for shipment, storage and disposal of nuclear materials and radioactive substances, on type-approval of
More informationMedical Devices. The technical requirements also apply when the submitter is not the legal manufacturer 1 (i.e: a distribution company).
UNFPA Technical requirements for medical devices 1. Introduction The following document provides UNFPA s technical requirements in the procurement of medical devices (medical equipment, renewable medical
More informationAnnular Core Research Reactor Pneumatic Transfer System Design
Annular Core Research Reactor Pneumatic Transfer System Design September 21, 2010 Tri Q. Trinh*, Ed Rombach + *Sandia National Laboratories, NM Albuquerque, NM 87185-1142 + Automation Concepts Inc. Sandia
More informationInternational Conference on Applications of Radiation Science and Technology (ICARST-2017) IAEA Headquarters, Vienna, Austria April 2017
International Conference on Applications of Radiation Science and Technology (ICARST-2017) IAEA Headquarters, Vienna, Austria 24 28 April 2017 15/04/2017 IAEA meeting, Warsaw 2016 1 UPGRADING AND CONTINUOUS
More informationSample Vial Secure Container SPECIFICATION. 1. Scope
1. Scope SPECIFICATION International Atomic Energy Agency (IAEA) inspectors must maintain continuity of knowledge on all destructive analysis (DA) samples shipped from nuclear facilities to the IAEA`s
More informationASA-100 QUALITY MANUAL
ASA-100 QUALITY MANUAL Origination Date: XXXX Document Identifier: Date: Document Revision: Latest Revision Date Abstract: This quality manual describes (your Company's) quality management system policies
More informationCOUNCIL OF STATE GOVERNMENTS - SOUTHERN STATES ENERGY BOARD RADIOACTIVE MATERIALS TRANSPORTATION COMMITTEE
COUNCIL OF STATE GOVERNMENTS - SOUTHERN STATES ENERGY BOARD RADIOACTIVE MATERIALS TRANSPORTATION COMMITTEE WHO IS GIPA? An alliance created to advocate the development of responsible regulations that enhance
More informationDEXION RACKING. The Product picture Effect of picture. 80/90/100/120/mm POST. Standard Medium Heavy Extra Heavy
DEXION RACKING Upright Profiles 75mm upright pitch Cold Forming Process on a high speed rolling mill Omega section, Front-Centre-Ribbed Powder coated finish Profile width 80x70, 90x70, 100x70, 120x70mm
More informationPRESENT STATUS OF LEGAL & REGULATORY FRAMEWORK AND DECOMMISSIONING PLANNING FOR DNRR. Prepared by NUCLEAR RESEARCH INSTITUTE, VAEC.
TECHNICAL MEETING ON THE RESEARCH REACTOR DECOMMISSIONING DEMONSTRATION PROJECT: CHARACTERIZATION SURVEY PHILIPPINES, 3 7 DECEMBER 2007 PRESENT STATUS OF LEGAL & REGULATORY FRAMEWORK AND DECOMMISSIONING
More informationANNEXURE "C1" Summary of Prices and Delivery Schedule. for Specification ZB for 220VDC STATION STORAGE BATTERY
ANNEXURE "C1" Summary of Prices and Schedule for Specification ZB-1530 for 220VDC STATION STORAGE BATTERY for Rutenberg Power Station, Unit 3&4 30/10/2017 Page C1 - G2-1 - of - 7 General Important Instructions
More informationSPECIFICATION FOR RUBBER INSULATING GLOVES FOR MEDIUM VOLTAGE CLASS 2, 3
Page no.: 1 SPECIFICATION FOR RUBBER INSULATING GLOVES FOR MEDIUM VOLTAGE CLASS 2, 3 ( חתום ( I.Bar-David Prepared by: Checked by: (חתום) A.Brodetsky )חתום ) N.Liberman Approved by: Page no.: 2 Contents:
More informationSUPPLIER REQUIREMENTS FOR QUALITY, DESIGN & MANUFACTURING
SUPPLIER REQUIREMENTS FOR QUALITY, DESIGN & MANUFACTURING 1.0 PURPOSE The purpose of this document is to define the requirements of Anaren Microwave, Anaren Ceramics and MS Kennedy (collectively Anaren)
More informationCapital Projects Group Air Filters and Accessories Specification
Capital Projects Group Air Filters and Accessories Specification Specification 23 41 00 Revision 0 Date: August 2018 Air Filters and Accessories Specification Specification 23 41 00 Publication Date: August
More informationPROCUREMENT QUALITY PROVISIONS Revision G January 9, 2017
NOTICE: PROCUREMENT QUALITY PROVISIONS Revision G January 9, 2017 The quality provisions below are part of the Purchase Order to the extent applicable. Supplier shall NOT disposition nonconforming material
More informationHarmonization with the International Atomic Energy Agency Regulation for the Safe Transport of Radioactive Material
United Nations Secretariat ST/SG/AC.10/C.3/2018/54 Distr.: General 11 April 2018 Original: English Committee of Experts on the Transport of Dangerous Goods and on the Globally Harmonized System of Classification
More information80/90/100/120/mm POST Standard Medium Heavy Extra Heavy
Upright Profiles 75mm upright pitch Cold Forming Process on a high speed rolling mill Omega section, Front-Centre-Ribbed Powder coated finish Profile width: 80x70, 90x70, 100x70, 120x70mm Standard JIS
More informationEPEAT CONFORMITY ASSESSMENT PROTOCOLS 4.5 Energy conservation
EPEAT CONFORMITY ASSESSMENT PROTOCOLS 4.5 Energy conservation 4.5.1 Power management system 4.5.1.1 Required ENERGY STAR Verification Guidance Product Verification Committee Clarifications References and
More informationDecommissioning the Philippine Research Reactor (Under R2D2P): Updates and Challenges
Decommissioning the Philippine Research Reactor (Under R2D2P): Updates and Challenges C.C. Bernido,, F.L. Santos, L.S. Leopando Philippine Nuclear Research Institute Philippine Research Reactor (PRR-1)
More informationRegional Workshop on Safety Review and Assessment for Regulators
Regional Workshop on Safety Review and Assessment for Regulators 9-13 September 2013 Thelma P. Artificio and Romelda P. Azores Nuclear Regulatory Division THE PHILIPPINES 7,107 Islands - Major island groups
More informationSection Table of Contents Page Number
Derby Fabricating Solutions Section Table of Contents Page Number 1.1 Introduction 2 1.2 Derby Quality Policy 2 1.3 Environmental Policy 2 1.4 Supplier Requirements Manual 2 1.5 Social Accountability 2
More informationMeggitt Oregon Purchase Order Quality Notes
QP-1 QP-2 QP-3 QP-4 QP-5 QP-6 QP-7 QP-8 Inspection System: Supplier shall maintain an inspection system that complies with ISO 9001; AS9100; Meggitt Supplier Quality Requirements Document - MPRC-10, or
More informationADVANCED DECONTAMINATION AND DECOMMISSIONING SYSTEM
ABSTRACT ADVANCED DECONTAMINATION AND DECOMMISSIONING SYSTEM Julia L. Tripp Idaho National Engineering and Environmental Laboratory P.O. Box 1625 Idaho Falls, Idaho 83415-3720 Radioactive waste packaging
More informationVendor Quality. Requirements Manual
ate Released 05/07/10 Last Review ate 03/14/16 Page 1 of 7 Vendor Quality Requirements Manual Nasco Aircraft Brake, Inc. 13300 Estrella Ave. Gardena California 90248 Telephone No. 310-532-4430 Fax. No.
More informationStacking columns for automotive logistics
Stacking columns for automotive logistics Standard and special solutions for all type of car parts transportation www.towersautomotive.com Our Company Towers Automotive is engineering, manufacturing and
More informationSECTION A. Product Data: Manufacturer's data sheets on each product to be used, including:
Page 1 of 7 SECTION 083925 MECHANICAL ROOM FLOOD DOORS AND FRAMES **Note to Specifier** This specification contains component and configuration options. Where indicated, choose the appropriate choice for
More informationSatellite Aerospace, Inc. TERMS & CONDITIONS Page 1 of 6
TERMS & CONDITIONS Page 1 of 6 1.0 PURPOSE 1.1 Satellite Aerospace, Inc. Quality Requirements to Subtier Sources. 2.0 SCOPE 2.1 This document applies to all purchasing and sales personnel responsible for
More informationA. The purpose of this section is to specify Division 23 responsibilities in the commissioning process.
SECTION 23 99 50 - (ADD#4) PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationIAEA Specification, Dismantle & installation of cooling system. Dated 2017/07/19
Dismantle & installation of 1. Introduction This Statement of work (SOW) describes the requirements for the services needed to refurbish the ( The System ) of the nuclear research reactor at the Instituto
More informationPRR-1 Decommissioning: Preparing for Dismantling and Decontamination. R2D2 Project Meeting, Manila, Philippines September
PRR-1 Decommissioning: Preparing for Dismantling and Decontamination R2D2 Project Meeting, Manila, Philippines 15-19 September 2008 1 Presented by Leonardo S. Leopando Philippine Nuclear Research Institute
More informationProposal Data. Submittal Form
Proposal Data Submittal Form Request for Proposal - Part Three of Four FORM REQUEST FOR The tables below are to be completed by the Contractor. Data that has already been input shall be met for any project
More informationPRODUCTION OF COBALT-60 IN PARR-1/KANUPP (CANDU) Mushtaq Ahmad Isotope Production Division, PINSTECH, Islamabad
PRODUCTION OF COBALT-60 IN PARR-1/KANUPP (CANDU) Mushtaq Ahmad Isotope Production Division, PINSTECH, Islamabad COBALT-60 Cobalt is a metal element with only one stable isotope: cobalt-59. When natural
More informationREGULATION REGARDING EQUIPMENT PROCUREMENT PROCESS AND APPROVAL OF MANUFACTURERS FOR NUCLEAR FACILITIES
REGULATION REGARDING EQUIPMENT PROCUREMENT PROCESS AND APPROVAL OF MANUFACTURERS FOR NUCLEAR FACILITIES SECTION ONE Purpose, Scope, Basis, Definitions and General Considerations Purpose and scope ARTICLE
More informationThe Selections Checked Below Apply To This Equipment
SCS CONVEYOR SYSTEM APPLICATION The SCS Conveyor System is a flexible, semi-automated (motorized and nonmotorized conveyors) or fully automated, modular conveyor system intended to heighten facility productivity
More informationOverview of Philippine Nuclear Regulations. Eulinia M. Valdezco Nuclear Regulations, Licensing and Safeguards Division
Overview of Philippine Nuclear Regulations Eulinia M. Valdezco Nuclear Regulations, Licensing and Safeguards Division Legal Framework Three (3) Laws exist but not covering decommissioning RA 2067 (The
More informationUser Requirement Specifications
Page 1 of 13 ANNEXURE III User Requirement Specifications MACHINE :Linear Bottle Washing CAPACITY: 120 Bottles/ minute Page 2 of 13 Table of Contents 1.0 APPROVAL SIGNATURES....03 2.0 INTRODUCTION...04
More informationSTANDARD QUALITY ASSURANCE PROVISIONS FOR PURCHASED MATERIALS
1. GOVERNMENT/CUSTOMER SOURCE INSPECTION: a. Government/Customer inspection is required prior to shipment from your plant. Upon receipt of this order, promptly notify the Government/Customer representative
More informationSchedule D3. Data Item Descriptions. Quality Assurance
DID, Front Cover QA Document Identifier Number: [* insert VSY Document #] Rev: 1 Title: DID Front Cover Quality Assurance Ship applicability: All Document Owner: [* insert name] Document Approver: [* insert
More informationPROForms. Specifications SECTION FIBERGLASS REINFORCED POLYMER (FRP) PULTRUDED PRODUCTS
PROForms Specifications SECTION 06600 FIBERGLASS REINFORCED POLYMER (FRP) PULTRUDED PRODUCTS Disclaimer BEDFORD REINFORCED PLASTICS INC. disclaims liability for any personal injury, property or other damages
More informationClauses applicable only when specified by Q-number on the purchase order.
Clauses applicable only when specified by Q-number on the purchase order. Q1 Certification of Raw Materials. Seller shall provide with each shipment, a certification of conformance to ARROW s specification
More informationAssociation of American Railroads Quality Assurance System Evaluation (QASE) Checklist Rev. 1/12/2017
Company: Prepared By: Date: Changes from previous version highlighted in yellow. Paragraph Element Objective Evidence 2.1 Objective of Quality Assurance Program 2.2 Applicability and Scope 2.3 QA Program
More informationSECTION A. Manufacturer's data sheets on each product to be used, including:
Page 1 of 7 SECTION 084239 PRESSURE-RESISTANT ENTRANCES **Note to Specifier** This specification contains component and configuration options. Where indicated choose the appropriate choice for your specific
More information2. GENERAL REQUIREMENTS
1. PURPOSE AND SCOPE 1.1 This document defines the Supplier Quality Requirements to be met by suppliers in the performance of the purchase order issued by Sagetech to ensure that externally provided processes,
More informationPurchase Order Quality Clauses These quality clauses are in addition to the Standard Ameriflex Inc.Terms & Conditions
Purchase Order Quality Clauses These quality clauses are in addition to the Standard Ameriflex Inc.Terms & Conditions Quality Requirements 1-9 are Mandatory on all Purchase Orders for products or services
More informationSupplier Quality Procurement Requirements (SQPR) DATED: 01/31/2018
Supplier Quality Procurement Requirements (SQPR) DATED: 01/31/2018 NOTE: Futuramic is responsible for ensuring all items procured from its supplier base including customer directed sources, conform to
More informationGrading of the Management System Requirements to the Safe
Grading of the Management System Requirements to the Safe Transport of Radioactive Materials Y.E. Tawfik ETRR-2 Complex, Egyptian Atomic Energy Authority, Cairo Egypt Received: 1/3/2016 Accepted: 7/6/2016
More informationSECTION A. Product Data: Manufacturer's data sheets on each product to be used, including:
Page 1 of 7 SECTION 083925 MECHANICAL ROOM FLOOD DOORS AND FRAMES **Note to Specifier** This specification contains component and configuration options. Where indicated, choose the appropriate choice for
More informationMevex Equipment for Phytosanitary Irradiation. Chapman University 2016 Tony Brown Mevex Corporation
Mevex Equipment for Phytosanitary Irradiation Chapman University 2016 Tony Brown Mevex Corporation Introduction to Mevex Manufacturers of medium sized electron beam accelerators E-beam systems from 2-40
More informationGamma irradiators. Andrzej G. Chmielewski. Training /learning course 2nd week at URCA Reims, France September 12-16, 2016
Joint innovative training and teaching/learning program in enhant and transfer knowledge of application of ionizing radiation in materials processing Gamma irradiators Andrzej G. Chmielewski Training /learning
More informationTable of Contents Table of Contents... 2 Introduction to Manual... 3 Scope... 3
Supplier Quality Manual Original Issue 12 February 2015 Uncontrolled in printed form Page 1 of 8 f Table of Contents Table of Contents... 2 Introduction to Manual... 3 Scope... 3 Supplier Responsibility...3
More informationSECTION A. Product Data: Manufacturer's data sheets on each product to be used, including:
Page 1 of 8 SECTION 083921 PEDESTRIAN FLOOD DOORS AND FRAMES **Note to Specifier** This specification contains component and configuration options. Where indicated, choose the appropriate choice for your
More informationPURCHASING QUALITY CLAUSES
Page 1 of 5 These requirements apply to all suppliers A. Right of Entry Tri Models, Tri Model s customer and their customers or applicable regulatory agencies shall have right of access to all facilities,
More information3.7 Radioactive Waste Management (RWM) Status in the Philippines
3.7 Radioactive Waste Management (RWM) Status in the Philippines The Philippine Nuclear Institute (PNRI), formerly the Philippine Atomic Energy Commission (PAEC), was created upon the passage of Republic
More informationPP Quality Assurance Procurement Clauses for Suppliers
PP 360.3 Quality Assurance Procurement Clauses for Suppliers Version No: 7 Created By: Approved By: Erik Keim on 01/29/2019 at 10:44 PM Eric Deffarges on 02/05/2019 at 09:17 AM Valid From: 06/12/2017 Strictly
More informationISO 9001 PMA and 14 CFR 21 QUALITY POLICIES HANDBOOK
ISO 9001 PMA and 14 CFR 21 QUALITY POLICIES HANDBOOK Origination Date: XXXX Document Identifier: Date: Document Revision: QMS-00 QMS Quality Policies Handbook Latest Revision Date Orig Abstract: This quality
More informationSECTION A. Product Data: Manufacturer's data sheets on each product to be used, including:
Page 1 of 8 SECTION 083919 WATERTIGHT DOORS **Note to Specifier** This specification contains component and configuration options. Where indicated, choose the appropriate choice for your specific project
More informationThese requirements apply to all suppliers:
Page 1 of 5 These requirements apply to all suppliers: A. Right of Entry Tri Models, Tri Model s customer and their customers or applicable regulatory agencies shall have right of access to all facilities,
More informationMain Page The Company The Technology Safety Locks Electric Lifts. Air Lifts
Incorporated date: 1985 Location: Walled Lake, Michigan Lot size: Approximately 3 acres Building: Approximately 33,000 square feet Military Application Employees: 40 Strengths: ISO certified Long Term
More informationLOW-LEVEL RADIOACTIVE WASTE FORUM, INC.
LOW-LEVEL RADIOACTIVE WASTE FORUM, INC. 2657 Bayview Drive Ft. Lauderdale, FL 33306 (754) 779-7551 * (754) 223-7452 FAX Disposition Options and Costs for Certain Radioactive Sealed Sources and Devices
More informationSTATEMENT OF WORK DIGITAL MAMMOGRAPHY UNIT AND ASSOCIATED SERVICES
1 1. Scope STATEMENT OF WORK DIGITAL MAMMOGRAPHY UNIT AND ASSOCIATED SERVICES 1.1. This Statement of Work (SOW) describes the requirements for the digital mammography equipment and associated services
More informationDangerous Goods and Rail Safety. A Technical Publication from the Co-ordination and Information Centre. Documentation Review
Dangerous Goods and Rail Safety A Technical Publication from the Co-ordination and Information Centre Documentation Review July 2017 - 2 - This material is meant as a guide to certain parts of the Transportation
More informationIncreasing Your Competitiveness in PCB Assembly
Increasing Your Competitiveness in PCB Assembly This article offers a seven step model for analyzing and integrating production systems. This phased approach can reduce costs, improve on-time delivery,
More informationTrident Precision Manufacturing
Trident Precision Manufacturing QASQC Rev. A 6/7/06 Title: Supplier Quality Clauses Author: April V. Lusk Director of Quality General Suppliers are responsible for compliance to all stated Quality Clauses
More informationPresented by Ananth Vas Director Marketing and Sales Symec Engineers (India) Pvt. Ltd.
Presented by Ananth Vas Director Marketing and Sales Symec Engineers (India) Pvt. Ltd. Symec Engineers (I) Pvt. Ltd. Is a Engineering company engaged in developing high technology custom designed equipment
More informationSpecification for Pipe Fittings
Specification for Pipe Fittings Specification for Pipe Fittings Page 1 of 11 Table of Contents 1.0 SCOPE...3 2.0 DEFINITIONS...3 3.0 REFERENCES, CODES AND STANDARDS...3 4.0 CONTRACTOR'S RESPONSIBILITIES...4
More informationWälischmiller Engineering
Wälischmiller Engineering Cutting-Edge Technology with Tradition Wälischmiller Engineering is a specialist manufacturer of remote-handling, robotics and radiation-protection solutions for environments
More informationREVISION RECORD AND DESCRIPTION CONTINUED ON NEXT PAGE.
REVISION RECORD REV DESCRIPTION DATE 0 INITIAL RELEASE 06/18/08 REVISION RECORD AND DESCRIPTION CONTINUED ON NEXT PAGE. CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART REVISION PAGE NO. 1 2 3 4 5 6 7 8
More informationOpenText Prime Protect
OpenText Prime Protect Software Maintenance Program Handbook 1. Introduction Welcome to Open Text Corporation s OpenText (OT) Prime Protect Software Maintenance Program. This handbook provides you with
More informationSITE MASTER FILE For MHRA
ABC CO., LTD. For MHRA Prepared by Date Approved by Date Verified by Date Document No.: SMF, Version No: 01, Effective Date: 09/05/06 Document No.: SMF Version No.: 01 Effective Date: 09/05/06 Page 2 of
More informationMechanical & Electrical Product Workmanship Standards Procedure
Workmanship Standards Page: 1 of 14 Mechanical & Electrical Product Workmanship Standards Procedure Workmanship Standards Page: 2 of 14 1.0 PURPOSE AND SCOPE 1.1 Purpose 1.1.1 The purpose of this procedure
More informationRevisions. SEPTA Specification
Revisions SEPTA Specification Change No. Release Date Reason for Change Release Approval 1 7/14/2016 Correct document quantities description 6.0, 7.1 change from one (1) to two (2) test units PJD 7/14/2016
More informationDELIVERY, SHIPMENTAND HANDLING
DELIVERY, SHIPMENTAND HANDLING 1. Delivery Instructions: The Equipment shall be delivered in accordance with INCOTERMS 2000 subject to the special terms specified in the Agreement/Purchase Order and the
More informationEXPRESSION OF INTEREST
EXPRESSION OF INTEREST White Rose Extension Project (WREP) EOI / Prequalification Multiphase Flow Meters EOI-101414-701.0 Mustang Canada, Inc is seeking prequalification responses from interested companies
More informationSUPPLIER QUALITY REQUIREMENTS
SUPPLIER QUALITY REQUIREMENTS TABLE OF CONTENTS 1) PURPOSE PG 2 2) KINNEAR PURCHASE ORDER PG 2 3) USE AND COMMUNICATION PG 2 4) SUPPLIER APPROVAL PG 2 5) GENERAL REQUIREMENTS PG 3 SQD Rev 2 2014-08-13
More informationD&D OF A PU EXTRACTION FACILITY IN VNIINM
ABSTRACT D&D OF A PU EXTRACTION FACILITY IN VNIINM S.V.Mikheikin, S.L.Khrabrov, A.Yu.Smirnov, L.V.Pronina, P.P.Poluectov, V.F.Derzhavin, A.Ya.Chilikin (VNIINM) V.D.Akhunov (Minatom) Old Pu extraction facility
More informationQ2A First Article Inspection (FAI) AS9102 Completely Revised
Page 1 of 6 Q2A First Article Inspection (FAI) AS9102 Completely Revised A hard copy of this document may not be the document currently in effect. The current version is always the version on the Lockheed
More informationOctaform Quick Liner Wall & Ceiling Panels Guide Specification CAN Page 1
Guide Specification CAN Page 1 This master guide specification Section is intended for use when specifying plastic panelling. This section includes performance, and descriptive type specifications; edit
More informationPURCHASE ORDER REQUIREMENTS (Quality Assurance Provisions)
PURCHASE ORDER REQUIREMENTS (Quality Assurance Provisions) Requirements 1-12 and 18 are applicable to all Mission Aerospace, Inc. purchase orders issued. Requirements 13-17 are applicable when specifically
More informationQuality Flow-Down Requirements to Suppliers
1.0 Calibration System: Seller s (herein referred to as Supplier) calibration system shall meet the requirements or standards of; ISO 9001, ISO 10012-1, or AS9100, and ANSI-Z540-1, or MIL-STD-45662. 2.0
More informationTransport Regulations (SSR-6 and SSG-26) 2015 Review Cycle
Transport Regulations (SSR-6 and SSG-26) 2015 Review Cycle Reviewer: Page... of... Country/Organization: Date: [1] Comment No. 1 2 3 [2] SSR-6/SSG-26 Para/Line No. 220 Table 1 COMMENTS BY REVIEWER [3]
More information(A.2) DURING PERFORMANCE OF THIS ORDER, YOUR QUALITY CONTROL SYSTEMS AND MANUFACTURING PROCESS ARE SUBJECT TO REVIEW, VERIFICATION,
(A) GENERAL: (A.1) PRATT & WHITNEY IS THE END USER. (A.2) DURING PERFORMANCE OF THIS ORDER, YOUR QUALITY CONTROL SYSTEMS AND MANUFACTURING PROCESS ARE SUBJECT TO REVIEW, VERIFICATION, ANALYSIS, AND APPROVAL
More informationStock Management Methods in SAP: Some distinctive differences between IM, WM, and EWM John Gardner
[ Stock Management Methods in SAP: Some distinctive differences between IM, WM, and EWM John Gardner [ We are an SAP Service Partner and Value Added SAP reseller. We are headquartered in Chicago, and with
More informationChapter 50. Radioactive Uranium Hexafluoride (UF6) Production, Processing and Use of UF6 50.1
Chapter 50 Radioactive Uranium Hexafluoride (UF6) 50.1 Production, Processing and Use of UF6 The raw material to make fuel for nuclear power stations is uranium ore, the main sources of which are South
More informationStatement of Work. Quality Management System (including data management and record keeping) development and implementation in Moldova
Statement of Work Quality Management System (including data management and record keeping) development in Moldova 1. Scope: The Statement of Work (SoW) describes the requirements for development and implementation
More informationDangerous Goods and Rail Safety. A Technical Publication from ALBERTA EDGE (ENVIRONMENTAL AND DANGEROUS GOODS EMERGENCIES) Documentation Review
Dangerous Goods and Rail Safety A Technical Publication from ALBERTA EDGE (ENVIRONMENTAL AND DANGEROUS GOODS EMERGENCIES) Documentation Review February 2018 - 2 - This material is meant as a guide to certain
More information