Schedule of Accreditation issued by United Kingdom Accreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK

Transcription

1 Schedule of ccreditation United Kingdom ccreditation Service 2 Pine Trees, Chertsey Lane, Staines-upon-Thames, TW18 3HR, UK ccredited to Moxley Industrial Centre Western Way Wednesbury WS10 7G United Kingdom Contact: Mr Philip Raybould Tel: +44 (0) Fax: +44 (0) philraybould@rotechlabs.co.uk Website: s covered by the organisation and their relevant activities Laboratory locations: details ctivity code ddress Western Way Wednesbury WS10 7G Local contact Mr Philip Raybould Testing Chemical tests Corrosion tests Mechanical tests Metallurgical tests Weldment Tests ddress Linley Lodge Laboratory Westgate ldridge Walsall WS9 8DG Local contact Mr Philip Raybould Testing Corrosion tests Mechanical tests Metallurgical tests Weldment Tests ssessment Manager: C3 Page 1 of 8

2 Schedule of ccreditation United Kingdom ccreditation Service ccredited to DETIL OF CCREDITTION METLS, LLOYS and METL PRODUCTS Chemical Tests luminium alloys Si, Fe, Mn, Cu, Mg, Zn, Cr, Pb, Sn, Ti RP101 using Optical Emission Spectroscopy luminium alloys (Wrought) Si, Fe, Cu, Mn, Mg, Cr, Ni, Zn, Ti, Pb, Sn, Zr, V, Ga, i s RP 116 & 117 using ICP-OES Ferrous ased lloys Mn, Si, P, Cu, Ni, Cr, Mo, V, Ti, l, Nb, Documented In0House s RP 116 & 117 using ICP-OES Ferrous ased lloys C, Mn, Si, S, P, Cu, Ni, Cr, Mo, Sn, Nb, V, l, Ti,, Zr, Pb, W, Co, Mg, N RP101 using Optical Emission Spectroscopy Nickel lloys C, Si, Mn, P, S, Cr, Mo, Ni, l, Co, Cu,, Ti, W, V, Nb, Fe, Ta, Zr RP101 using Optical Emission Spectroscopy Determination of Carbon and Sulphur RP138 Cast iron, copper alloys, ferro alloys, high alloyed steels, low alloyed steels, nickel and cobalt alloys, plain carbon steels and refractories Qualitative and Semi- Quantitative analysis of elements above atomic No.5 RP362 using Energy Dispersive Spectroscopy High alloyed steels, low alloyed steels, nickel and cobalt alloys, plain carbon steels. Determination of Nitrogen RP136 ssessment Manager: C3 Page 2 of 8

3 Schedule of ccreditation United Kingdom ccreditation Service ccredited to METLS, LLOYS and METL PRODUCTS (cont d) Corrosion Tests ustenitic stainless steels Susceptibility to intergranular corrosion S EN ISO :1998 STM Practice, C and E STM G48-11 ustenitic stainless steels Susceptibility to intergranular corrosion STM Practice E STM G48-11 Wrought nickel rich chromium bearing alloys Susceptibility to intergranular corrosion STM G28-02(15) Mechanical Tests end S EN ISO 7438:2016, Hardness: rinell (5/750, 10/3000) S EN ISO :2014 STM E10:15 Rockwell Scales & C S EN ISO :2016 STM E18-16 Vickers HV5, 10, 30 and 100 S EN ISO :2005 STM E92-16 Vickers HV10 and 30 S EN ISO :2005 STM E92-16, Low Force Vickers HV0.3, 0.5 and 1 S EN ISO :2005, Micro Hardness HV 0.10 STM E384-11e1 Micro Hardness HV 0.3, 0.5 and 1.0 STM E384-11e1 ssessment Manager: C3 Page 3 of 8

4 Schedule of ccreditation United Kingdom ccreditation Service ccredited to METLS, LLOYS and METL PRODUCTS (cont d) Mechanical Tests Impact: Izod S 131:Part 1:1961(2015) Charpy (V- and U- notches) (-196 C and -140 C to ambient) S EN ISO 148-1:2010 STM E23-16b STM 923:2014, Crystallinity S 131:Part 5:1965(2015) Tensile Tensile (mbient temperature, forces from 2 kn to 600 kn) S EN ISO :2016 s & STM E8/8M-16a STM STM M-10, Tensile (temperatures from ambient to 600 C, forces from 2 kn to 100 kn) S EN ISO :2011 STM E21-09 Pipes and tubes Crush, Flattening and Expanding S EN ISO 8492:2013 S EN ISO 8493:2004 S EN ISO 8495:2013 S 6323:Part 1:1982(1990) (Superseded) STM ssessment Manager: C3 Page 4 of 8

5 Schedule of ccreditation United Kingdom ccreditation Service ccredited to METLS, LLOYS and METL PRODUCTS (cont d) Mechanical Tests (cont d) Fasteners (Including olts, Screws and Nuts) Proof Load and Tension S 4395:Part 1:1969 (withdrawn) S 4395:Part 2:1969 (withdrawn) S EN ISO :2009 S EN ISO :2009 S EN ISO 898-1:2013 S EN ISO 898-2:1992 S EN ISO 898-6:1996 (withdrawn) STM F606-14a STM F606M-14a STM F738-02(2008) STM Partial decarburization depth S EN ISO 898-1:2013 Metallurgical Tests ustenite spacing Case depth (Surface Hardened Layers) DNV-RP- F112 October 2008 S 6286:1982(2005)/ISO 4970:1979 S EN ISO 2639:2002 S EN 10328:2005 Depth of Decarburisation S EN ISO 3887:2003 Detrimental intermetallic phases STM 923:2014, Dezincification S EN ISO 6509:1995 S 2345:2006 Grain size (Comparison) S EN ISO 643:2012 STM E112-13( ) Grain size (Comparison) STM E112-13( ) Graphite in Iron STM S EN ISO 945-1:2008 ssessment Manager: C3 Page 5 of 8

6 Schedule of ccreditation United Kingdom ccreditation Service ccredited to METLS, LLOYS and METL PRODUCTS (cont d) Metallurgical Tests Inclusion content ( only) ISO 4967:2013ED3 STM E45-13 Macrostructure STM E381-01(2012) STM 604/604M- 07(2017) Fractographic and microscopical examination RP 361 Volume fraction STM E562-11, Weldments and razing Tests designated in specified Welding s as detailed below:- end, Fracture, Hardness, Impact, Tensile, Visual examination, Macro / Micro examination S EN 287:Part 1:2011 S EN ISO :2004 S EN ISO :2004+2:2012 S EN ISO :2005 S EN ISO 9016:2012 S EN ISO 5178:2011 S EN ISO4136:2012 S EN ISO 5173:2010+1:2011 S EN ISO 17637:2016 S EN ISO :2011 S EN ISO :2016 S EN ISO 9017:2013 S EN ISO 17639:2013 S EN ISO :2016 S 1140:1993 S 4871:Part 3:1985 S 4872:Part 1:1982 S 4872:Part 2:1976 S EN ISO 15620:2000 SME IX:2015, ssessment Manager: C3 Page 6 of 8

7 Schedule of ccreditation United Kingdom ccreditation Service ccredited to METLS, LLOYS and METL PRODUCTS (cont d) Weldments and razing (cont d) Tests designated in specified Welding s as detailed below:- T/SP/P1-Feb 02 T/SP/P2-Sept 03 GC/PS Part P5:1976 GC/PS Part P8:1975 T/SP/P9- pril 03 DGQ V.P84 D CR 8-10 S EN ISO 15613:2004 S EN 288-9:1999 (Withdrawn) S EN ISO 9018:2015, METLLIC COTINGS Corrosion Tests Neutral salt spray STM S EN ISO 9227:2012 Metallurgical Tests Plating/coating thickness S EN ISO 1463:2004 S EN ISO 1456:2009 Coating mass S EN 10346:2015 S EN 10152:2017 Chemical Test Chromate treated surfaces Presence of hexavalent chromium Documented In-house RP110 ssessment Manager: C3 Page 7 of 8

8 Schedule of ccreditation United Kingdom ccreditation Service ccredited to PINT and VRNISHES Environmental Tests Resistance to dry heat Immersion Salt spray resistance Resistance to Humidity (continuous condensation) (cyclic condensation) S U 148 Part 9:1969(1990) (Withdrawn) s based on customer specifications S U 148 Part 13:1969(1990) (Withdrawn) s based on customer specifications S U 148 Part 2:1969(1990) (Withdrawn) STM S EN ISO :2001 Mechanical Tests dhesion S EN ISO 2409:2013 Ford FLTM I Hardness S U 148 Part 6:1969(1990) (Withdrawn) Clause 3 Pencil method PLSTIC COTINGS Corrosion Tests Salt spray resistance STM END ssessment Manager: C3 Page 8 of 8