Introduction. Introduction. The micro mechanical properties of the wood cell wall. Xinan Zhang M.S. Candidate

Transcription

1 The micro mechanical properties of the wood cell wall Xinan Zhang M.S. Candidate Nowadays, with the fast development of nanotechnology, more attention has been paid to micro and sub-micro scale area. The micro mechanical properties and sub-micro mechanical properties of wood cell wall are paramount because of its potential applications in wood based nano-composites in future. As far as wood science aspect is concerned, the mechanical contribution of process in the cell wall is not fully understood. Nanoindentation testing Wimmer was the first to prove the capability of nanoindentation to determine mechanical properties of cell walls in wood. It allows an indenter to penetrate the sample of a material, at the same time, the penetration depth and load can be recorded. As a result, the stiffness and hardness of the indented location can be calculated. 1

2 P H = A E r max dp 1 = dh 2 E = (1 v s 2 s π A 1 1 v )( E E r 2 i 1 i ) Strain gradient effects are unavoidable Micro-pillar compression test Through this effective experiment, the yield stress and modulus of the material can be tested. Strain gradients can be avoided. Micro-pillar model Zhang H, Schuster BE, Wei Q, Ramesh KT. The design of accurate micro-compression experiments. Scripta Materialia 2006;54: Fillet radius/post radius ratios of are recommended The post aspect ratio (defined as height/diameter ratio) of 2 3 is reasonable Taper of the pillar should be minimized during micro-pillar fabrication, it would results in overestimated elastic modulus, spurious strain hardening and increased apparent yield 2

3 Michael D. Uchic, Dennis M. Dimiduk. A methodology to investigate size scale effects in crystalline plasticity using uniaxial compression testing. Materials science and engineering A (2005) Invested a methodology for performing uniaxial compression tests on samples having micron-size dimensions. Sample fabrication is accomplished using focused ion beam milling to create cylindrical samples of uniform cross-section that remain attached to the bulk substrate at one end. Once fabricated, samples are tested in uniaxial compression using a nanoindentation device outfitted with a flat tip, and a stress strain curve is obtained. a single-crystal Ni superalloy, D<5 um, size effect appeared. 3

4 C. A. VOLKERT and E. T. LILLEODDEN. Size effects in the deformation of sub-micron Au columns. Philosophical Magazine 2006 (86) Single crystal Au columns ranging in diameter from 180nm to 8 um. The compressive yield stress scales roughly as the inverse square root of the column diameter. Stresses as large as 1 GPa are reached. Johann Michler, Kilian Wasmer, Stephan Meier, and Fredrik Östlunda. Plastic deformation of gallium arsenidemicropillars under uniaxial compression at room temperature. Applied physics letters 2007 (90) Compressive strength of gallium arsenide (GaAs) pillars with a diameter of 1 um by uniaxial compression tests. The micropillars were found to exhibit ductile plasticity comparable to macroscopic tests. The yield stress was 1.8±0.4 GPa 4

5 Julia R. Greer, Warren C. Oliver, William D. Nix. Size dependence of mechanical properties of gold at the micron scale in the absence of strain gradients. Acta materialia 2005(53) Uniaxial compression experiments on gold at the sub-micron scale, without stress/strain gradients. A significant flow stress increase, up to several GPa. These high strengths appear to be controlled by dislocation starvation, unique to small crystals. H. Bei, S. Shim, E.P. George, M.K. Miller, E.G. Herbertc and G.M. Pharr. Compressive strengths of molybdenum alloy micro-pillars prepared using a new technique. Scripta materialia 2007 (57) chemically etching Single-crystal micro-pillars of a molybdenum alloy Diameter ranging from 360 to 1000 nm. 5

6 Focused ion beam (FIB) FIB is a useful technology using gallium liquid metal ion source (LMIS) for sample preparation. FIB Started in 1974 Liquid source: Cesium, gallium, mercury and so on Long lifetime (over 500 h) and high stability variation (less than ±1%) The typical accelerating voltage is between 5 and 50 kev while the primary ion penetration depth is ~20 nm (25 kev Ga+) FIB Application FIB technology was first used to improve semiconductor devices for maskless implantation techniques. Then the FIB became a powerful tool for transmission electron microscopy (TEM) sample preparation. Although the most popular application area of FIB is semiconductor field, FIB is a versatile tool, it can mill most kinds of materials. It can be used in solid state devices for lithography, etching, deposition and doping. 6

7 lithography etching deposition doping Application in wood science Steffen Orso Ulrike G. K. Wegst Eduard Arzt The elastic modulus of spruce wood cell wall is about 28 GPa Damage in the sample surface It was reported that at 30 kev, the top 25 nm of a silicon substrate will be amorphized. Minimize the milling time Lowering the gallium ion energy in the final step of milling A plasma cleaner. Low energy Ar ions were induced by immersing the sample in the plasma source, while the ratio of Ar:O 2 is 3:1. Yet some researchers said that the results obtained from a wide range of materials show that important results can be received without damage layer removal. 7

8 Objectives The objective of this work is to investigate the micro mechanical properties of wood cell wall through a micro-pillar uniaxial compression test. The sample will be prepared by a focused ion beam (FIB) system. Yield stress and modulus of wood cell wall will be invested, and this engineering modulus can be compared with the result got by nanoindentation test. AFM non-contact mode for surface scan Materials Softwood --loblolly pine Hardwood -- teak In the same growth ring to minimize any unintended variations 8

9 Equipment Microtoming (glass knife and diamond knife) Optical microscopy Atomic force microscopy (AFM) Scanning electron microscopy (SEM) Focused ion beam (FIB) Micro-compression system Nanoindentation Initial sample preparation Late wood part of the sample will be chosen and cut into 3mm 3mm 2mm. Embede in Spur resin, which is commonly used as an embedding medium for electron microscopy of biological samples. Microtoming glass knife and diamond knife Name ERL-4221 DER-736 NSA DAME pr opor t i on wei ght 2. 5g 1. 5g 6. 5g 0. 1g 9

10 SEM beam energy 3KV working distance about 6mm aperture 60mm loblolly pine FIB milling Beam voltage 30 kev Bean current na Extraction voltage 6.33kV Emission current 2.4 kv Species Number Micro-column diameter (um) Height (um) Fillet radiuses (um) Loblolly pine Teak

11 Micro-compression system Optical Microscopy Moving stage Micro-compression tip Tip Micro-pillar uniaxial compression test l l0 l ε = = l 0 l0 P P σ = = A 1 π d 4 σ E = ε 2 11

12 Acknowledgements Dr. Siqun Wang Dr. John Dunlap Dr. Cheng Xing Dorothy Coffey Rosa Trejo (UTK) (UTK) (UTK) (ORNL) (ORNL) Questions? Thank you 12