Asbestos/Lead Paint Survey

Transcription

1 Asbestos/ Survey At: Camp Lejeune Bldg. 500 Repair Indoor Physical Fitness Center Prepared for: The Walker Group Architecture Inc. PO Box 541 New Bern, NC PEI Project No.: Walker Group Project No.: AL Date: Inspectors: June 20, 2017 Jonathan Guetta, Michael Krupa NC Asbestos Inspectors: 11936/12880 NC Lead Inspector/Risk Assessor Prepared by: 3802 Cherry Ave. Wilmington, NC Tel: (910) Fax: (

2 3802 Cherry Ave. Wilmington, NC Tel: Fax: June 19, 2017 The Walker Group Architecture, Inc. Attn: Beth Walker PO Box 541 New Bern, NC Re: Asbestos Bulk Sampling & Analysis at: Camp Lejeune Building 500 Repair Indoor Physical Fitness Center Contract No. N D-0857 Client Project No.: PEI Project No.: AL On June 14, 2017, Jonathan Guetta and Michael Krupa (NC Asbestos Building Inspector Accreditation Nos and 12880, respectively) of Precision Environmental, Inc. (Precision) conducted an asbestos survey within the above referenced building. The inspection included all materials scheduled to be disturbed/removed during the upcoming renovation project as described in the written scope of work supplied to Precision by the Client. The purpose of the survey was to verify the presence or absence of asbestos-containing materials (ACM) associated with the building prior to renovation procedures. Prior to sample collection, a visual inspection was conducted in order to determine homogeneous materials/areas and sample locations. Asbestos-containing materials are defined as materials that contain greater than 1% asbestos via Polarized Light Microscopy (PLM). Homogeneous Areas (HGA) are determined by the material s color and texture. Asbestos-containing materials are defined by the following descriptions: surfacing material (SM), thermal system insulation (TSI) and miscellaneous materials (M). Both friable and non-friable materials were included in the inspection. Friable materials are defined as those that can be pulverized by hand pressure. Bulk sampling of suspect ACM was conducted in accordance with the sampling requirements promulgated by the United States Environmental Protection Agency s Asbestos-Containing Materials in Schools Rule (40 CFR 763, Subpart E), commonly referred to as the Asbestos Hazard Emergency Response Act or AHERA regulations. Specific compliance to these requirements include, but are not limited to, the type and number of samples to be collected. Sample locations were selected at random. As a result, a total of thirty-seven (37) bulk samples were collected from sixteen (16) suspect asbestos-containing materials. A listing of identified suspect ACM materials and the number of samples collected from each homogeneous area (HGA) is provided in Table 1 below: Table 1: Identified Suspect Asbestos Materials Suspect material (HGA) Description Friable/Nonfriable Sample Location No. of Samples Collected 1. Textured wall plaster SM F 1 st Floor Main Gym Area 5 2. Textured ceiling material SM F 1 st Floor Front Lobby Area 3 3. Wallboard M F 1 st Floor Storage Room below stairs, 2 nd Floor Hallway 2 4. Joint compound M F 1 st Floor Storage Room below stairs, 2 nd Floor Hallway 2 5. Stone pattern linoleum flooring M NF 1 st Floor Men s Bathroom (top layer) 2 6. Black floor tile/mastic M NF 1 st Floor Men s Bathroom (bottom layer) 2

3 The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Asbestos Survey Report June 19, 2017 Page 2 of 4 Suspect material (HGA) Description No. of Samples Friable/Nonfriable Sample Location Collected 7. Felt paper below Gym hardwood flooring M NF 1 st Floor Main Gym Area 2 8. Mastic below rubber floor tiles M NF 1 st Floor Rear Locker Room 2 9. Hard wall plaster SM F Rear Gym Vestibules x 12 beige marbled floor tile/mastic M NF 2 nd Floor Hallway x 12 white floor tile/mastic M NF 2 nd Floor Center Office 2 12.Covebase mastic M NF 2 nd Floor Hallway Gray duct mastic M NF Attic White exterior window caulking M NF Exterior windows White exterior door caulking M NF Exterior doors Roofing shingles M NF Rooftop 2 SM=Surfacing material/tsi=thermal system insulation/m= Miscellaneous material/f=friable/nf=non-friable Collected samples were given a unique identification number, which included the date, building number (500) and sample number, logged onto a chain of custody form and shipped to an accredited laboratory for analysis. All samples were analyzed by Polarized Light Microscopy (PLM) via EPA method 600/M4/82/020. Multi layered samples were separated prior to analysis and analyzed separately per EPA protocol. In an effort to reduce cost, Precision instructed the laboratory to STOP analysis at the first positive sample for each suspect material HGA and not to analyze the remaining samples from the same HGA. As a result, a total of thirty-nine (39) samples were analyzed. Results Laboratory analysis of the bulk samples collected revealed that suspect material 1 contains asbestos in quantities greater than 1% and is considered to be an asbestos-containing material. The remaining suspect materials revealed no asbestos detected and may be treated as NON-ACM. Listing of identified ACM and NON-ACM materials is provided in Table 2 below: Table 2: Identified ACM and NON-ACM Materials Material Description Friable/ Non-friable Location Laboratory Result Approx. Quantity 1. Textured wall plaster SM F 1 st Floor Main Gym Area 2. Textured ceiling material SM F 1 st Floor Front Lobby Area 2% Chrysotile asbestos Trace Chrysotile asbestos 2,555 SF N/A 3. Wallboard M F Throughout building None detected N/A 4. Joint compound M F Throughout building None detected N/A 5. Stone pattern linoleum flooring M NF 1 st Floor Men s Bathroom (top layer) and Rear Locker Room Area Bathrooms None detected N/A 1 st Floor Men s Bathroom (bottom layer) None detected N/A 6. Black floor tile/mastic M NF 7. Felt paper below Gym hardwood flooring M NF 1 st Floor Main Gym Area None detected N/A

4 The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Asbestos Survey Report June 19, 2017 Page 3 of 4 Material Description Approx. Friable/ Location Laboratory Quantity Non-friable Result 8. Mastic below rubber floor tiles M NF 1 st Floor Rear Locker Room None detected N/A 9. Hard wall plaster SM F Throughout building None detected N/A x 12 beige marbled floor tile/mastic M NF Throughout 2 nd Floor None detected N/A x 12 white floor tile/mastic M NF Throughout 2 nd Floor None detected N/A 12.Covebase mastic M NF Throughout 2 nd Floor None detected N/A 13. Gray duct mastic M NF Throughout building None detected N/A 14. White exterior window caulking M NF Exterior windows None detected N/A 15. White exterior door caulking M NF Exterior doors None detected N/A 16. Roofing shingles M NF Rooftop None detected N/A SF = Square Feet N/A = Not Applicable Based on the sample analysis, the following materials should be considered to be Asbestos-Containing Materials: Textured wall plaster located in the 1 st Floor Main Gym Area (approximately 2,555 square feet) Asbestos-containing materials are regulated materials and must be handled accordingly. If the materials are to be disturbed/removed, the materials must be removed in accordance with all applicable Federal, State and Local regulations. In addition, the materials must be disposed of as asbestos-containing waste and may not be disposed of as construction debris. A physical/visual inspection revealed the following: No destructive investigation techniques were used during this inspection. It should be understood that suspect asbestos-containing pipe insulation materials may exist within presently concealed wall and/or ceiling cavities and pipe chase spaces. Non-suspect ceramic tile floors were noted in bathrooms within the building. Non-suspect FRP wall board material was noted within interior bathrooms. Non-suspect T1-11 boards were noted within the Gym area. Non-suspect wood base molding was noted in various areas within the building. Non-suspect fiberglass pipe insulation and associated fiberglass and/or PVC fittings were noted throughout the interior spaces (including bathrooms) within the building. Non-suspect rubber flooring material was noted in the locker rooms. Non-suspect fiberglass duct insulation was noted on the ductwork in the locker rooms. The ceiling of the main gymnasium space was noted to consist of confirmed non-asbestos-containing wallboard and joint compound materials. Non-suspect fiberglass pipe insulation and fiberglass duct insulation were noted in the attic. Piping within the confined space steam pit at the rear of the building appeared to be insulated with non-suspect fiberglass pipe insulation. Non-suspect fiberglass pipe insulation and duct insulation materials were noted within the crawlspace. The exterior soffit/overhang was noted to consist of non-suspect concrete. No suspect asbestos-containing window glazing compound was noted at the windows. Non-suspect vinyl siding was noted at the upper exterior facades of the building. All efforts were made to discover/sample all suspect asbestos-containing materials. If additional materials not addressed during this inspection are to be disturbed, Precision strongly recommends that those materials either be assumed to be asbestoscontaining, or that bulk samples be collected to determine the materials asbestos content prior to their disturbance.

5 The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Asbestos Survey Report June 19, 2017 Page 4 of 4 All bulk samples analytical results as well sample location are outlined in detail on the attached BULK SAMPLE DATA AND CHAIN OF CUSTODY form and laboratory s BULK ASBESTOS ANALYSIS RESULTS form. Attached please find the following: Bulk Asbestos Analysis Sheet Bulk Sample Data And Chain Of Custody Form Laboratory and Personnel Certificates If you have any questions or require additional information, please do not hesitate to contact me at (910) Sincerely, Precision Environmental, Inc. Michael Krupa NC Asbestos Inspector Accreditation #12880

6

7

8

9

10

11

12

13

14

15 3802 Cherry Ave. Wilmington, NC Tel: Fax: June 19, 2017 The Walker Group Architecture, Inc. Attn: Beth Walker PO Box 541 New Bern, NC Re: Bulk Sampling & Analysis at: Camp Lejeune Bldg. 500 Repair Indoor Physical Fitness Center Contract No. N D-0857 Client Project No.: PEI Project No.: AL Precision Environmental Inc. (Precision) was retained by The Walker Group Architecture, Inc. to conduct a lead paint survey and analysis of coated surfaces associated with the above referenced facility. The inspection included all materials scheduled to be disturbed/removed during the upcoming renovation project as described in the written scope of work supplied to Precision by the Client. The purpose of the survey was to determine if lead painted components exist within and on the exterior of the the structure prior to renovation procedures. The bulk sampling was performed by Precision s representative, Jonathan Guetta (NC Risk Assessor/ Lead Inspector Certificate No ) on June 14, As a result, a total of twenty-two (22) different suspect lead based paint (LBP) coatings were identified. A listing of the identified LBP coatings and the number of bulk samples collected per suspect material is provided in Table 1 below: Table 1: Identified suspect LBP coatings materials Suspect Material Location No. of Samples Collected 1. White painted wood T-111 Walls Gymnasium 2 2. White painted metal exterior door systems Exterior doors 2 3. White painted wood base board Gymnasium 2 4. White painted plaster walls Gymnasium 2 5. White painted wallboard ceiling Gymnasium 2 6. Black painted metal stair railing Stairways 2 7. Black painted concrete stair tread Stairways 2 8. White painted wallboard walls 2 nd floor walls 2 9. White painted metal interior door systems 2 nd floor interior doors White painted metal radiator covers 2 nd floor radiators White painted metal toilet partition Toilet partitions Orange painted metal I-beams Attic Yellow painted metal interior stairway safety paint Stairways Gray painted concrete floor At rear entry 2

16 Suspect Material Location 15. White painted brick walls Locker room White painted horizontal concrete beams Locker room mezzanine Gray painted metal I-beams Locker room mezzanine Cream/gray painted metal exterior stair system Rear stair system Gray painted metal exterior door system Front and side exterior entries White painted metal columns Exterior, front White painted concrete overhang ceilings Front overhangs White painted metal side entry lintels Side entries 2 The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Survey Report Precision No AL Page 2 of 4 No. of Samples Collected Collected samples were given a unique identification number, which included the date, building number (500), and periodic table of elements lead symbol (Pb), sample number, logged onto a lead paint chip chain of custody form and shipped to an accredited laboratory for analysis. The bulk samples collected from the above listed materials (Table 1) were analyzed by Flame Atomic Absorption (AA) via EPA SW and 3050B Method. Analysis of the samples revealed that multiple suspect coatings contain lead in concentrations above the Detection Limit. Laboratory results obtained are provided in detail in the attached laboratory report and summarized in the Table 2 below: Table 2: Summary of Laboratory Results Suspect Material Location Highest Lead Concentration % by weight 1. White painted wood T-111 Walls Gymnasium < White painted metal exterior door systems Exterior doors < White painted wood base board Gymnasium White painted plaster walls Gymnasium White painted wallboard ceiling Gymnasium Black painted metal stair railing Stairways Black painted concrete stair tread Stairways White painted wallboard walls 2 nd floor walls White painted metal interior door systems 2 nd floor interior doors White painted metal radiator covers 2 nd floor radiators White painted metal toilet partition Toilet partitions Orange painted metal I-beams Attic Yellow painted metal interior stairway safety paint Stairways Gray painted concrete floor At rear entry White painted brick walls Locker room Detection Limit % by weight

17 Suspect Material Location The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Survey Report Precision No AL Page 3 of 4 Highest Lead Concentration % by weight 16. White painted horizontal concrete beams Locker room mezzanine Gray painted metal I-beams Locker room mezzanine Cream/gray painted metal exterior stair system Rear stair system Gray painted metal exterior door system Front and side exterior entries White painted metal columns Exterior, front White painted concrete overhang ceilings Front overhangs White painted metal side entry lintels Side entries Detection Limit % by weight Based on the laboratory analysis, the following components associated with the structure are confirmed to be coated with lead based paint and shall be handled in accordance will all applicable regulations: All white painted wood baseboard All white painted plaster walls All white painted wallboard ceilings All black painted metal stair railings All black painted concrete stair treads All White painted wallboard walls All white painted metal interior door systems All white painted metal radiator covers All white painted metal toilet partitions All orange painted metal I-beams All yellow painted metal interior stairway safety paint All gray painted concrete floors All white painted brick walls All white painted horizontal concrete beams All gray painted metal I-beams All cream/gray painted metal stair systems All gray painted metal exterior door systems All white painted exterior metal columns All white painted concrete overhang ceilings All white painted metal side entry lintels Note: OSHA defines any detectable level of lead in paint a concern when renovations/demolition will impact lead coated surfaces. A visual inspection revealed the following: Metal HVAC duct in the attic is unpainted Bathroom partitions are coated in veneer Recommendations/Control Options If renovation or demolition activities are to impact lead coated surfaces, all work should be conducted by workers trained in lead safe work practices as outlined by the Occupational Safety and Health Administration (OSHA). In addition all lead coated components or paint removed from lead coated components should be disposed of in accordance with all Federal, State, and Local regulations.

18 The Walker Group Architecture, Inc. Repair Indoor Physical Fitness Center Bldg 500, Camp Lejeune, NC Survey Report Precision No AL Page 4 of 4 If additional materials not addressed during this inspection are to be disturbed, Precision strongly recommends that those materials either be assumed to be coated with lead based paint or that sampling is conducted to confirm the presence of absence of lead based paint prior to the disturbance of the materials. If you have any questions or require additional information, please do not hesitate to contact me at (910) Sincerely, PRECISION ENVIRONMENTAL INC. Jonathan Guetta NC Lead Inspector/Risk Assessor #: Attachments: Paint Chip Sample Data and Chain of Custody Laboratory Data Sheets Laboratory and Inspector Certificates

19 30105 Beverly Road Romulus, MI Ph: ; Fax: Certificate of Analysis: Lead In Paint by EPA SW and 3050B* Client : Attn : Phone : Precision Environmental 161 Arlington Dr. Wilmington, NC J. Guetta Fax : jguetta@precision-enviro.com AAT Project : Sampling Date : 06/14/2017 Date Received : Date Analyzed : Date Reported : 6/20/2017 8:00:38PM Client Project : Project Location : AL Repair Indoor Physical Fitness Center Bldg 500 Lab Sample ID Client Code Sample Description PPM Result Lead (% by weight) Calculated R L (% by weight) PB-01 T-111 WALLS GYM WHITE WOOD <25 < PB-02 T-111 WALLS GYM WHITE WOOD <16 < PB-03 EXTERIOR DOOR SYSTEMS WHITE METAL <11 < PB-04 EXTERIOR DOOR SYSTEMS WHITE METAL <14 < PB-05 BASE BOARD GYM WHITE WOOD PB-06 BASE BOARD GYM WHITE WOOD PB-07 GYM WALLS WHITE PLASTER PB-08 GYM WALLS WHITE PLASTER PB-09 GYM CEILING WHITE WALLBOARD PB-10 GYM CEILING WHITE WALLBOARD <19 < PB-11 STAIR RAILINGS BLACK METAL PB-12 STAIR RAILINGS BLACK METAL PB-13 STAIR TREAD BLACK CONCRETE PB-14 STAIR TREAD BLACK CONCRETE PB-15 2ND FL OFFICE AREA WALLS WHITE WLB PB-16 2ND FL OFFICE AREA WALLS WHITE WLB <17 < PB-17 2ND FL INTERIOR DOOR SYSTEMS WHITE <20 < PB-18 2ND FL INTERIOR DOOR SYSTEMS WHITE PB-19 2ND FL RADIATOR COVERS WHITE PB-20 2ND FL RADIATOR COVERS WHITE <19 < PB-21 2ND FL TOILET PARTITION WHITE RL= Reporting Limit * For true values assume (2) significant figures. The method and batch QC is acceptable unless otherwise stated. Current EPA/HUD Interim Standard for lead in paint samples is: 5000 PPM (parts per million) or ug/g which is equivalent to 0.5% by weight. AAT internal sop S203. The laboratory operates in accord with ISO guidelines and holds limited scopes of accreditation under AIHA-LAP and NY State DOH ELAP programs. These results are submitted pursuant to AAT LLC current terms and conditions of sale, including the company's standard warranty and limitation of liability provisions.analytical results relate to the samples as received by the lab. AAT will not assume any liability or responsibility for the manner in which the results are used or interpreted. Reproduction of this document other than in its entirety is not permitted. All Quality control requirements for the samples this report contains have been met. AAT does not blank correct reported values. Sample data apply only to items analyzed. *= Validated modified method AIHA LAP- Lab ID #100986, NY State DOH ELAP -Lab ID #11864, State of Ohio- Lab ID # Date Printed: 8:02PM AAT Project: Page 1 of 4

20 Lab Sample ID Client Code Sample Description PPM Result Lead (% by weight) Calculated R L (% by weight) PB-22 2ND FL TOILET PARTITION WHITE PB-23 ATTIC I BEAMS ORANGE METAL PB-24 ATTIC I BEAMS ORANGE METAL PB-25 INTERIOR STAIRWAY SAFETY PAINT YLW PB-26 INTERIOR STAIRWAY SAFETY PAINT YLW PB-27 FL BY REAR SIDE ENTRYWAY GRAY PB-28 FL BY REAR SIDE ENTRYWAY GRAY PB-29 LOCKER ROOM REAR WALL WHITE PB-30 LOCKER ROOM REAR WALL WHITE PB-31 LOCKER RM MEZZ SUPPORT SYS WHITE PB-32 LOCKER RM MEZZ SUPPORT SYS WHITE <23 < PB-33 I BEAM LOCKER ROOM MEZZ GRAY PB-34 I BEAM LOCKER RM MEZZ GRAY PB-35 EXTERIOR STAIR RAIL REAR CREAM GRAY PB-36 EXTERIOR STAIR RAIL REAR CREAM GRAY PB-37 EXTERIOR DOOR SYSTEM FRONT GRAY PB-38 EXTERIOR DOOR SYSTEM SIDE GRAY PB-39 FRONT COLUMNS EXT WHITE PB-40 FRONT COLUMNS EXT WHITE PB-41 FRONT OVERHANG CEILING WHITE PB-42 FRONT OVERHANG CEILING WHITE PB-43 SIDE ENTRY LINTELS WHITE PB-44 SIDE ENTRY LINTELS WHITE Analyst Signature RL= Reporting Limit * For true values assume (2) significant figures. The method and batch QC is acceptable unless otherwise stated. Current EPA/HUD Interim Standard for lead in paint samples is: 5000 PPM (parts per million) or ug/g which is equivalent to 0.5% by weight. AAT internal sop S203. The laboratory operates in accord with ISO guidelines and holds limited scopes of accreditation under AIHA-LAP and NY State DOH ELAP programs. These results are submitted pursuant to AAT LLC current terms and conditions of sale, including the company's standard warranty and limitation of liability provisions.analytical results relate to the samples as received by the lab. AAT will not assume any liability or responsibility for the manner in which the results are used or interpreted. Reproduction of this document other than in its entirety is not permitted. All Quality control requirements for the samples this report contains have been met. AAT does not blank correct reported values. Sample data apply only to items analyzed. *= Validated modified method AIHA LAP- Lab ID #100986, NY State DOH ELAP -Lab ID #11864, State of Ohio- Lab ID # Date Printed: 8:02PM AAT Project: Page 2 of 4

21 30105 Beverly Road Romulus, MI Ph: ; Fax: To : Precision Environmental 161 Arlington Dr. Wilmington, NC Attn : J. Guetta jguetta@precision-enviro.com Phone : Project Location : Repair Indoor Physical Fitness Center Bldg 500 AAT Project : Client Project : Date Reported : AL 6/20/2017 8:00:38PM Sample Client Code Analysis Requested Completed Analyst PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB-27 This report is intended for use solely by the individual or entity to which it is addressed. It may contain information that is privileged, confidential and otherwise exempt by law from disclosure. If the reader of this information is not the intended recipient or an employee of its intended recipient, you are herewith notified that any dissemination, distribution or copying of this information is strictly prohibited. If you have received this information in error, please notify AAT immediately. Thank you. AIHA LAP- Lab ID #100986, NY State DOH ELAP -Lab ID #11864, State of Ohio- Lab ID # Date Printed: 8:02PM AAT Project: Page 3 of 4

22 Sample Client Code Analysis Requested Completed Analyst PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB PB-44 Reviewed By Quality Assurance Coordinator - Robert A Theys This report is intended for use solely by the individual or entity to which it is addressed. It may contain information that is privileged, confidential and otherwise exempt by law from disclosure. If the reader of this information is not the intended recipient or an employee of its intended recipient, you are herewith notified that any dissemination, distribution or copying of this information is strictly prohibited. If you have received this information in error, please notify AAT immediately. Thank you. AIHA LAP- Lab ID #100986, NY State DOH ELAP -Lab ID #11864, State of Ohio- Lab ID # Date Printed: 8:02PM AAT Project: Page 4 of 4

23

24

25

26

27

28

29

30

31