1.5 snap lock sl 150

Transcription

1 1.5 snap lock sl 150 Strip Width Base Material Thickness Min Tensible Min Yield Coatings to 24 Steel.0128 to.027 in 52 - ksi 50 - ski Painted / Galvalume UL CONSTRUCTION NUMBERS: TGKX301, tgkx342a, tgkx388 The Snap Lock 1.5 (SL150) combines the architectural aesthetics and the structural performance, all in one panel that can be fabricated on site for all the substrates described in the UL Construction numbers mentioned above. UL performed tests For Uplift Resistance of Roof Assemblies UL 580, CLASS 90 For impact resistance of prepared Roof-Covering Materials UL2218, CLASS 4 Fire Tests of roof Coverings UL 790, EXTERNAL FIRE EXPOSURE Features 24 ga steel or 26 ga steel. Colors available on standard or premium and metallic. 12 to 24 o.c. On site factory made. Available in smooth, striated, offset and stiffener Ribs. Finish Kynar 500, Galvalume, Galvanized. requirements Solid substrate (plywood, concrete, etc.), rigid insulation Vapor barrier (When using rigid insulation or solid substrate Bearing Plate (When using sigid insulation on top of metal decking) Minimum Roof Slope 3 : 12 1

2 1.5 SNAP LOCK SL150 undewriters laboratories approval UL Construction Number Panel Coverage (in) Gauge Clip Max. Clip spacing Roof Substrate Impact Resistance UL-2218 Fire Rating UL-263 Uplift Resistance UL Min Fix 1-6 Plywood Class 4 Class A Class A Min Fix 1-6 Composite System Class 4 Class A Class Min Fix 1-6 Composite System Class 4 Class A Class 90 Notes Test Procedures are in accordance with Underwriters Laboratories Standard UL-580 under Test for Uplift Resistance of Roof Assemblies. the panel qualifies for a Class A fire rating in compliance with Underwriters Laboratories Standard UL-263 when installed over a non-combustible substrate and Class C fire rating can be obtained as well. QM SL 150 Panels carry a Class 4 rating under UL-2218 Test Standard for Impact Resistance A detail method of installation is available for each Construction Number above that can be found in the UL Roofing Materials Directory. 2

3 ul construction number tgkx Metal Roof Deck Panels* - No. 24 MSG min coated steel panels, 20 in. wide, 1-½ in. high at female side rib. Panels continuous over three or more clips with no end laps. A bead of sealant may be used at panel side joints. A.Metal Roof Deck Panels* - No. 24 MSG min coated steel panels, 19.5 in. max width 1- ½ in. high at female side rib. Panels continuous over three or more clips with no end laps. A bead of sealant my be used at panel side joints. 2.Roof Deck Fasteners* (Panel Clips) - One pied assembly, 1-3/4 in. wide, 1-5/16 in. high. min thickness in. (No. 24 MSG) Clips spaced 18 in. OC fastened to plywood deck. 3. Fasteners (Screws) - Fasteners used to attach panel clips (Item 2 and 2A) to plywood to be No by 1 in. long pancake head, No. 2 Phillips drive, A-point, coated steel screw. Min one fastener per clip to be used. 5. Plywood Decking - Plywood decking to be graded per PS83 specifications, 19/32 in. thick, exposure 1, APA rated 20 in. OC, square edged. Butt ends not blocked. All butt and side joints to be sealed with a one part urethane caulk sealant applied with a caulking gun and feathered outward from the joint (Note exception under item 4, alternate). 6. Supports - Spaced max of 244 in OC Any of the following types may be used to support the plywood decking: A. 2 by 6 in., min No. 2 grade A.F.P.A. S-P-F Hemlock Fir our Southern Pine or equivalent. B. Wood trusses with a nom 2 by 4 in. upper chord of the same grade as Item a. C. No. 22 MSG min cold formed coated steel (min yield to be 33,000 psi) 7. Plywood Fasteners - Fasteners used to attach the plywood deck to the supports to be as follows: A. For plywood - to - wood supports No by 7-7/8 in. long bugle-head steel screws with a No. 2 Phillips drive, a "Hi-Low" thread pattern and an "S-Point". B. As an alternate to Item a, 8 d by 2-½ in. long deformed shank common nails may be used. C. For plywood - to - steel supports for steel thickness less than No. 20 MSG No by 1-1/4 in. long bugle- head steel screws with a No. 2 Phillips head drive "Hi-Low" threads and "S-Pint". For a steel thickness greater than No. 20 MSG to No. 16 MSG, No by 1-1/4 in. long bugle-head steel screws with a No. 2 Phillips drive and an S12 (TEEKS/3 ) point. Spacing: Fastener spacing for all fastener types to be 6 in. O.C. at the plywood edges and 12 in. O.C. in the interior

4 ul construction number tgkx342a 1. Metal Roof Deck Panels* - No. 24 MSG min gauge coated steel. Panel width may be 20 in. or 12 in. Panel ribs to be 1-½ high at female side. Panels continuous over three or more clips with no end laps. A. Metal Roof Deck Panels* - No. 24 MSG min coated steel panels, 19.5 in. max width, 1-½ in. high at female side rib. Panels continuous over three or more clips with no end laps. A bead of sealant may be used at panel side joints. 2. Roof Deck Fasteners * (Panel Clips) - One piece assembly, 1-3/4 in. wide 1-5/16 in. high min thickness in. No. 24 MSG Clips spaced 18 in. O.C. A. Roof Deck Fasteners* (Panel CLips) - One piece assembly, 2-1/4 in. wide, 1-1/8 in high, min thickness in. No. 24 MSG Clips spaced 18 in. OC, fastened to plywood deck. 3. Gypsum Board* (Mineral Board) - Min thickness ½ in. Opposite side edges have an tongue and groove configuration. Butt (end) joints to be staggered and occur over steel deck crests. Wallboard installed perpendicular to steel deck corrugations. 4. Vapor Barrier - Single ply, used between the wallboard and metal roof deck panels to be a min 30 lb roofing felt. 5. Joint Tape - (Not Shown) - All wallboard joints shall be taped with 2.5 in. wide joint tape supplied. 6. Foamed Plastic -(Rigid Insulation) - (Optional) - Expanded polystyrene supplied in 4 by 8 ft sheets, min thickness 13/16 in., min density 1.0 pcf or (Rigid Insulation) Polyisocyanurate supplied in 4 by 8 ft sheets or (Rigid Insulation) Phenolic supplied in 4 by 8 ft sheets. All end joints to be staggered with respect to adjoining rows. All joints to be offset from joints in mineral board (Item 3) 7. Fasteners - For Attaching panel clips to steel deck to be min one in. diam threaded shank Phillips, bugle or trumpet head, self-drilling, self-tapping, corrosion resistant coated steel screws supplied by roof deck manufacturer. Screws shall penetrate steel deck min ½ in. A. Fasteners - For attaching wallboard to steel deck (Item 8) to be min in. diam threaded shank Phillips, bugle or trumpet head, self - drilling, self- tapping, corrosion resistant coated steel screws supplied by the manufacturer. Screws are installed into top corrugations of steel deck through nom 3 by 3 in. corrosion resistant steel roof deck plates, spaced in a pattern as determined by the pitch of the steel deck with the min density of 21 fasteners per 4 by 8 ft sheet of gypsum board (Item 3). 8. Steel Deck - Fabricated to various profiles, min yield strength 33,000 psi. Steel deck profile, thickness, support spacing and method of positioning (end and side laps) and fastening deck to supports to be per deck manufacturers requirements for uplift loading. A. Deck Fasteners - Steel deck panels to be fastened to structural supports and at laps using ARC spot welds with weld washers or screw fasteners per deck manufacturer's requirements for uplift loading. 9. Purlins - 16 MSG min gauge steel (min yield strength 50,000 PSI) or min Type H open web joists. 1-6 MAX A MAX 4 7A

5 ul construction number tgkx Metal Roof Deck Panels* - No. 24 MSG min coated steel panels, 20 in. wide, 1-½ in. high at female side rib. Panels continuous over three or more clips with no end laps. A bead of sealant may be used at panel side joints. A.Metal Roof Deck Panels* - No. 24 MSG min coated steel panels, 19.5 in. max width 1- ½ in. high at female side rib. Panels continuous over three or more clips with no end laps. A bead of sealant my be used at panel side joints. 2.Roof Deck Fasteners* (Panel Clips) - One pied assembly, 1-3/4 in. wide, 1-5/16 in. high. min thickness in. (No. 24 MSG) Clips spaced 18 in. OC fastened to plywood deck. 3. Fasteners (Screws) - Fasteners used to attach panel clips (Item 2 and 2A) to plywood to be No by 1 in. long pancake head, No. 2 Phillips drive, A-point, coated steel screw. Min one fastener per clip to be used. 5. Plywood Decking - Plywood decking to be graded per PS83 specifications, 19/32 in. thick, exposure 1, APA rated 20 in. OC, square edged. Butt ends not blocked. All butt and side joints to be sealed with a one part urethane caulk sealant applied with a caulking gun and feathered outward from the joint (Note exception under item 4, alternate). 6. Supports - Spaced max of 244 in OC Any of the following types may be used to support the plywood decking: A. 2 by 6 in., min No. 2 grade A.F.P.A. S-P-F Hemlock Fir our Southern Pine or equivalent. B. Wood trusses with a nom 2 by 4 in. upper chord of the same grade as Item a. C. No. 22 MSG min cold formed coated steel (min yield to be 33,000 psi) 7. Plywood Fasteners - Fasteners used to attach the plywood deck to the supports to be as follows: A. For plywood - to - wood supports No by 7-7/8 in. long bugle-head steel screws with a No. 2 Phillips drive, a "Hi-Low" thread pattern and an "S-Point". B. As an alternate to Item a, 8 d by 2-½ in. long deformed shank common nails may be used. C. For plywood - to - steel supports for steel thickness less than No. 20 MSG No by 1-1/4 in. long bugle- head steel screws with a No. 2 Phillips head drive "Hi-Low" threads and "S-Pint". For a steel thickness greater than No. 20 MSG to No. 16 MSG, No by 1-1/4 in. long bugle-head steel screws with a No. 2 Phillips drive and an S12 (TEEKS/3 ) point. Spacing: Fastener spacing for all fastener types to be 6 in. O.C. at the plywood edges and 12 in. O.C. in the interior o.c. Max 18 o.c. Max

6 1.5 snap lock sl 150 Introduction SL-150 is a non-structural panel which is mechanically seamed during installation. The product is an integral interlocking system by design meaning the panels install in one direction from a given starting point. SL-150 is a very flexible panel design which works well with a wide range of building designs. Two clips are available: Floating Clip and Fixed for fixing panel at center point allowing for multi-directional expansion. Factory Apply Sealant available. Design Completely Concealed Fastened Roofing SL-150 Standing Seam requires low maintenance. The panel is secured with concealed clips and the panel side laps are locked together using a rooftop seaming machine. Applications Product uses include low to high slope roofing, vertical fascia, equipment screens, mansards, and wall panels. This system may also be installed on tapered and curved roof areas. Typically specified as an accent feature for schools, shopping centers, banks, hotels, offices, and a variety of other applications. Tools and Equipment Installer must have prior experience and knowledge of the tolls listed below and their uses in working with metal roofing. Caulking Gun Snips Cordless Screw Gun Pop Rivet Tool Tape Measure Hemming Tool Electrical Extension Cord Heavy Gloves Safety Glasses. Specifications Color and Finishes 24 and 26 Gauge Galvalume 35 Year Finish Warranty on Kynar 500 Finish Widths Actual Panel Coverage (Width): 17 and 20 Minimum Slope = 3":12" Lengths SL-150 Panel is available in standard lengths from 4 to 40. Longer lengths require additional handling, packaging, and shipping considerations. An extra handling charge may apply to panels over 40. Continuous Rollformed Lengths: eliminates need for panel lap joints. Installation Solid Substrate Required Seamer Machine Required Weather Tight Warranty is not Available Underlayment Required Oil Canning Offset, striations and pencil ribs provide strength and reduce the incidence of oil canning in the panels. Testing UL 790 Fire Test of Roof Coverings, Class A, B, C UL 2218 For Impact Resistance, Class 4 UL 580 Uplift Resistance. Class 90 Construction No Packaging Options Standard packing A packaging charge will be added to all orders. Standard packing is crating for all orders. LTL packing For LTL, panels are packaged in a completely enclose crate to provide optimum protection. Additional charges will apply for non-standard packing and special requests. 6

7 Strippable film Removal The panels may have a protective strippable film layer applied to the topside of the panel to prevent possible damage to the painted surface. If panel has a protective film coating, remove the film before exposing to direct sunlight and high temperatures. After exposure to sunlight, the film cannot be removed. Under no circumstances should the film remain on the panels after installation. Receiving Materials It is the responsibility of the installer to unload material from the delivery truck. The installer shall be responsible for providing suitable equipment for unloading of material from the delivery truck. After receiving material, check the condition of the material, and review the shipment against the shipping list to ensure all materials are accounted for. If damages or shortages are discovered, it should be noted on the shipping copy at time of delivery. If material is delivered by common carrier, a claim must be made with the carrier as soon as possible. Manual Handling A panel should never be picked up by its ends. Instead, lift the panel along its longitudinal edge and carry in a vertical (not flat) position. Safety Metal Panels can become slippery, so always wear shoes with non-slip soles. Walking or Standing on a metal roof which do not have plywood or other deck beneath it is not recommended. However, if you must do so, always walk on the purlins, never between. Delivery and Packing Options Lead Time Please allow 2-3 days for delivery for material or colors we have in stock. Color we have to paint please allow working days. Touch Up Paint All painted panels and flashings have a factory applied baked on finish. Handling and installing panels may result in some small scratches or nicks to the paint finish. Touch-up paint is available in matching colors. It is recommended that a small brush be used to apply touch-up paint to those areas that are in need of repair. Touch-up paint does not have the superior chalk and fade resistance of the factory applied paint finish and will normally discolor at an accelerated rate. Periodic touch-up may be required to maintain color match. There is no warranty on touch-up paint in regards to color match because the paint processes are different. Aerosol paint should not be used because of the overspray that may occur. Storage Bare Galvalume and painted panels can be expected to give many years of rust-free service when precautions are taken during storage. If metal is not to be used immediately, store inside in a well ventilated, dry location. Any outdoor storage is at the customer s own risk! At time of delivery, inspect panels for moisture. If moisture has formed, the panels should be uncrated, wiped dry, and allowed to dry completely. Failure to remove the entrapped moisture between the sheets immediately will affect the service life of the metal. Extended storage of panels in a bundle is not recommended. Storage on Roof, Crates need to be placed parallel to the framing members and the slope of the roof. Load capabilities of the structure must be checked prior to placing crates on the roof. 7

8 trim hip ridge valley w/ integral cleat drip edge locking pitch change z bar end wall 8

9 RC24-SO13 A= 6 B=½ RC24-SO12 A=5 B=1 RC24-SO16 A=7 B=1 RC24-SO20 A=9½ B=1 RC24-SO24 A=11 B=1 RCS24-SO16 A= 4½ B=1 C=2 D=½ PC24-SO16 A= 5 B=1 C=2 D=7½ E=½ zee bar Z24-SO414 A=1 B=1 ¾ C=1 3 ¾ 2.85 VENTED ZEE AVAILABLE, PLEASE INQUIRE 9

10 GUS24-SO235 A=4 B=4 C=7 D 3½ E=1 GU24-SO2114 A= 4½ B= 5¼ C 5½ D= 3 E= 1 F=1 21 ¼ 20 DS24-SO1618 A= 4 B= 3 C= 3½ VC24-SO24 A=4 B=1 C=5 D=1 E=1 10

11 j-trim A JC24-SO06 A=3 3/8 B=1 1/8 C=1 D=½ D B C FW24-SO1078 A=6 B=5 5/8 C=1 ¼ D=½ EW24-SO09 A=3 B=5 C=1 HIGH SIDE FASCIA FH24-SO13 A=3 B=5 C=½ 11

12 1.5 snap lock sl150 ACCESSORIES pipe flashing metal to metal metal to wood pancake wood pancake metal clips sealants 12

13 ACCESSORIES ITEM PIPE FLASHING - GRAY EPDM PIPE FLASHING - SILICONE PIPE SIZE RANGE 1¼ TO ⅛ 1¼ TO 2 1¾ TO 4 1¼ TO 4 3 TO 6 4 TO 7 6 TO 11 7 TO TO TO 24 PIPE SIZE RANGE 1¼ TO 4 4 TO 7 7 TO TO 18 DESCRIPTION EPDM rubber service temperature 65 f to 250 f if slope is more than 20 use next size up BASE DIMENSION 3½ 3¾ 6¼ 7¾ 9¼ 10¾ 14½ 16½ 25⅜ 39½ X 35 SQ BASE DIMENSION 7 3¾ 10 ¾ 16 ½ 16 ½ (HIGH TEMPERATURE) RETROFIT PIPE FLASHING GRAY EPDM PIPE SIZE RANGE ¾ TO 2¾ 2 TO 7 ¼ 3 ¼ TO 10 silicone service temperature 40 to 350 if slope is more than 20 use next size up BASE DIMENSION 6 ¼ 10 ¾ 14 ½ POP RIVET utility snaplock clip finish plain stainless steel # 42, #43, #44, #46 painted stainless steel #42 EPDM rubber service temperature 65 f to 250 f if slope is more than 20 use next size up Box size panel system height gauge box qty sl 150 ⅞ kynar 500 flashing- 24 ga typ galvalume Acrylic coated galvalume galvalume is a trade mark of biec, inc. 13

14 ACCESSORIES ITEM Pancake wood 1 DESCRIPTION finish Bag size Box size plain x 1 No. 2 phillips self drilling 1 pancake finish Bag size Box size plain 250 2, x 1 No. 2 phillips finish Bag size Box size plain 250 2,000 painted 250 2,000 ¼- 14 x ¾ type ab metal to wood finish Bag size plain 250 painted 250 Box size 2,000 2, x 1 type 17 metal to wood 10 oz tube np1 caulk sealer kynar 500 flashing- 24 ga typ galvalume Acrylic coated galvalume galvalume is a trade mark of biec, inc. type color carton qty carton weight np1 np1 np1 np1 np1 np1 np1 np1 clear gray gray bronze tan almond black white green

15 EAVE DETAIL STANDING SEAM CLIP EAVE FLASHING FASTENER CLEAT SET IN SEALANT PLYWOOD DECKING CONTINUOUS CLEAT PA-5 KEEPER STANDING SEAM CLIP FIELD CUT & BEND RETURN IN PANEL W/SEALANT & HOOK OVER EAVE FLASHING STANDING SEAM CLIP PLYWOOD DECKING EAVE FLASHING CONTINUOUS CLEAT PA-1116 EAVE EAVE FLASHING PLYWOOD DECKING CLEAT SET IN SEALANT CONTINUOUS CLEAT ED

16 FASCIA RAKE WALL DETAIL STANDING SEAM FASCIA STANDING SEAM CLIP W/ FASTENER FASCIA/RAKE WALL FLASHING W/J-CLOSURE FIELD-FORM PANEL LEG TO I.D. OF J-CLOSURE SEALANT PLYWOOD DECKING FRWD

17 FASCIA TO SOFFIT TRANSITION PLYWOOD SUBSTRATE SANDING SEAM CLIP W/ FASTENER FRAMING MEMBERS SOFFIT PANEL FASCIA TO SOFFIT FLASHING J-CLOSURE FOR SOFFIT 30 # FELT STANDING SEAM CLIP W/ FASTENER PLYWOOD SUBSTRATE SOFFIT PANEL J-CLOSURE FOR SOFFIT FASCIA TO SOFFIT FLASHING FTST

18 GABLE DETAIL GABLE FLASHING W/J CLOSURE FIELD-FORM PANEL LEG TO I.D. OF J-CLOSURE SEALANT CONTINUOUS CLEAT PLYWOOD DECKING STANDIGN SEAM CLIP W/ FASTENER GD

19 GUTTER DETAIL STANDING SEAM CLIP W/ FASTENER GUTTER STRAP (FIELD-FORMED) GUTTER FLASHING FASTENER CLEAT SET IN SEALANT PLYWOOD DECKING GUTTER SUPPORT AS SPECIFIED BY ARCHITECT GD

20 HIP/RIDGE DETAIL HIP/RIDGE FLASHING W/ Z CLOSURE 3/4 TURN - UP SEALANT (AT VERTCAL SEAM & UNDER Z ) STANDING SEAM CLIP W/ FASTENER PLYWOOD DECKING GtD

21 HIgh side detail HIGH SIDE FLASHING W/ Z CLOSURE 3/4 TURN-UP STANDING SEAM CLIP W/ FASTENER SEALANT (AT VERTICAL SEAM & UNDER Z ) CLEAT PLYWOOD DECKING HSD

22 head wall detail FASTENER 3/4 TURN-UP COUNTER FLASHING W/REGLET & Z CLOSURE SL150 PANEL STANDING SEAM CLIP W/ FASTENER SEALANT (AT VERTICAL SEAM & UNDER Z ) PLYWOOD DECKING 30 # FELT HWD

23 inside corner detail FIELD-FORM PANEL LEG TO I.D. OF J-CLOSURE INSIDE CORNER FLASHING W/ J CLOSURE SEALANT PLYWOOD SUBSTRATE STANDING SEAM CLIP W/ FASTENER icd

24 outside corner detail STANDING SEAM CLIP W/ FASTENERS SL-150 PANEL PLYWOOD SUBSTRATE 30# ROOFING FELT FIELD - FORMED PANEL SEALANT ocd

25 pitch change detail STANDING SEAM CLIP W/ FASTENER PITCH CHANGE FLASHING W/ Z CLOSURE 3/4 TURN - UP SL150 PANEL SEALANT (AT VERTICAL SEAM & UNDER Z ) PLYWOOD DECKING pchd

26 rake detail FASTENER RAKE FLASHING W/REGLET & J- CLOSURE FILED - FORM PANEL LEG TO I.D. OF J - CLOSURE SEALANT PLYWOOD DECKING STANDING SEAM CLIP W/ FASTENER rkd

27 SILL DETAIL STANING SEAM CLIP W/ FASTENER PLYWOOD SUBSTRATE SILL FLASHING SLd

28 VALLEY DETAIL STANDING SEAM CLIP W/FASTENER VALLEY FLASHING CLEAT SET ON SEALANT PLYWOOD DECKING VDd

29 VENTED RIDGE DETAIL 3/4 TURN - UP RIDGE VENT FLASHING W/ Z CLOSURE PERFORATED Z POP RIVET STANDING SEAM CLIP W/ FASTENER PLYWOOD DECKING SEALANT (AT VERTICAL LEG & UNDER Z ) VRd