INSTALLATION INSTRUCTIONS SORIC INTEGRATION CENTER
|
|
- Toby O’Brien’
- 5 years ago
- Views:
Transcription
1 INSTLLTION INSTRUCTIONS SORIC INTEGRTION CENTER TEC-F-0018 REV2 3/11
2 SITE CONDITIONS Shipping Weight SORIC lbs. SORIC lbs. Rough Opening Recessed applications require a 74 W x 79 H x 30 D rough-in opening. Consideration and planning must be given by the general contractor to provide access panels above the unit for future service access and to provide stainless steel trim around the cabinet. Flooring Conditions The unit is equipped with leveling feet which will compensate for un-level floors. pplications requiring seismic anchorage require removal of leveling feet and use of shimming material to achieve a level state. Verify that the concrete slab to which unit is anchored is not cracked. Electrical Electrical services shall be provided by general contractor in accordance with facility requirements and national and local code ordinances by the general contractor. ll wall j-boxes rough-in must be completed prior to installation of the unit. Communication & Other Services Communications and other services shall be provided by general contractor in accordance with facility requirements. SORIC unit shall provide junction boxes to facilitate utility services. Cabinet provides an optional removable panel on the rear to facilitate utility routing. It is recommended to have the utilities be delivered from a junction box that is mounted behind one of the access panels in the upper compartment or in the lower compartments. Seismic nchorage Seismic applications require specific anchorage. Equipment anchorage provided by others. Calculation specification sheets available from SKYTRON. Structural Engineer of Record (SEOR) shall design the correct embedment and check the floor structure to support loading. nchors must be at an adequate distance from all slab openings or edges. Verify that anchors used to secure the unit are at an adequate distance from any new or existing anchors. Surface Preparations ll finished surfaces are coated with a protective layer of plastic sheeting. It will be necessary to remove portions of this sheeting during the installation process and once the installation is complete. To assist in the process of removal it is recommended to use a heat gun on a low setting to help soften the grip of the plastic to the stainless steel. Recommended tools - Heat Gun Cleaning Instructions The exterior and interior of the cabinet should be cleaned regularly using a mild soap and water solution or a cleaner formulated for stainless steel and a soft cloth. Do not use strong soaps, abrasives or steel wool. Tools required: Phillips screwdriver or drill with Phillips #2 bit Level Materials handling equipment Utility knife Slotted screwdriver set Wire strippers U.S. socket set U.S. open end wrench set Recommended: Heat Gun
3 SORIC INSTLLTION INSTRUCTIONS Page 1 ll versions of the SKYTRON SORIC units are shipped in two (2) crates. The top and bottom sections are shipped independently to facilitate shipping and handling procedures. Position the two crates near the installation area prior to removing the crating to avoid damage. Remove all crating material and remove the two sections from the respective bases. Refer to figure 1 on page 2. Caution should be observed as the optional Back Cover is shipped loose. Install optional back access cover using #10x5/8 SS TEK screws provided, place the completed assembly in final position and adjust leveling feet as required. NOTE Silicone, food grade caulking is recommended as a sealant in seams and joints along the desktop surfaces for added protection. Consult local and state codes for specific requirements. WRNING lways use caution when lifting and positioning. Follow OSH and state safety guidelines to avoid personal injury. Employ additional assistance if required. CUTION ll exposed surfaces are covered with a protective layer of plastic. This will need to be removed prior to final assembling of the unit. Place the upper section on the base unit, align the fastening holes and secure the two sections with the #10x5/8 SS TEK screws provided. lign the pins on the bottom of the side panels with the holes in the base unit, install the side panels and secure with the #10-32 screws provided. Side panels may be installed at a later date to facilitate utility routing and termination. Install all electrical and communications outlets with cabling as required. These are specific to each application and must be performed by a qualified electrician. During most applications, the electrical contractor should provide flexible conduit to facilitate sliding the unit in and out of placement. Install shelf clips (16) in upper compartments as desired and install shelves with the cable access holes to the rear. WRNING lways exercise caution when handling equipment to avoid personal injury. This equipment and all input leads provided by facility must be circuit protected and wired in accordance with all current applicable state, local and NEC codes. lways consult with the manufacturers of all Endoscopy, Video or other equipment to be used on the SORIC for all communications and services required within the unit or to external equipment. Due to the number of application variables, SKYTRON does not provide this information. ssembly Components (shipped inside the drawer) include: - #10-32 Phillips, pan head screws - Shelf brackets - Cabinet keys - #10x5/8 SS TEK pan head screws
4 Page 2 SHELF (4) BCK CCESS COVER (optional) UPPER SECTION #10x5/8 PNHED PHILLIPS (18) SHELF BRCKET (4 per shelf) OPTIONL SKYTRON SURGICL LIGHT PNEL PIN 4-GNG INSIDE PNEL (1) LEFT (1) RIGHT #10x5/8 PNHED PHILLIPS (20) (optional) #10-32 PNHED PHILLIPS FSTENING HOLES BSE KEYS (2) REMOVBLE INNER PNEL (1) LEFT (1) RIGHT 1/2" NUT LEVELING FEET (8) 3/8" THRED NOTE Refer to specific seismic calculations if applicable SORIC-72 SHOWN FRONT VIEW SORIC-72 Figure 1.
5 NOTE: SORIC-72 SHOWN, OTHER MODELS SIMILR Page 3 OPTIONL SLOPED TOP (lign with top of cabinet and secure with 1/4"-20 screws provided) 1/4"-20 SCREW REVERSE NGLE UPPER COMPRTMENT SINGLE GNG JUNCTION BOXES FOR ELECTRICL ND COMMUNICTIONS CONNECTORS (7 total) 2 GNG JUNCTION BOX 120VC, 4, 30W (work surface light connection) 2" x 6" THRU HOLE FOR CBLE ROUTING (3) REMOVBLE PNELS (from inside of upper compartments) SIDE PNEL RCEWY (1 each side) DESK UNIT RCEWY (1 each side) 4 GNG JUNCTION BOX (2 each side) (internally mounting inside left and right panels) 2 GNG JUNCTION BOX (internally mounting inside left and right panels) 2 GNG JUNCTION BOX (internally mounting inside left and right panels) 2.25" THRU HOLE FOR CBLE ROUTING (2) Figure 2.
6 Page 4 OPERTING ROOM INTEGRTION CENTER SORIC-72 3 LIFT & SLIDE POCKET DOORS (TEMPERED GLSS) 4 DJUSTBLE SHELVES 3 FLUORESCENT LIGHT FIXTURE COMPUTER COMPRTMENT PULL OUT WORK SURFCE DJUSTBLE LEVELING FEET (8) REMOVBLE VENTED INNER PNELS INTRODUCTION SKYTRON s SORIC-72 Operating Room Integration Center provides the perfect communications center for PCS and video integration, as well as networking of multiple services within the facility. The SORIC-72 provides a shared hub for information systems distribution within and outside the surgical suite. OPTIONS Standard Phone, Computer and Video Connectors can be provided. Specify type. Control of Lighting, udio, Video, Data and MIS Equipment System operations can be provided as custom applications. RCHITECTURL SPECIFICTIONS Operating Room Integration Center shall consist of a stainless steel cabinet designed to store video, audio and communications equipment. Junction boxes shall be provided for ease of routing electrical, communication and video cabling. Upper compartments have three lift and slide, tempered glass pocket doors, and four adjustable stainless steel shelves. Lower compartment shall include mounting location for SkyVision and a pull-out work surface. Heavy duty, adjustable leveling feet shall be included. Built-in chase shall allow space for up to four 20 mp circuits. Hospital Grade Electrical Receptacles are available for upper and lower compartments.
7 SORIC-72 OPTIONL REMOVBLE BCK PNEL (2) 4 GNG SWITCH BOXES 8"x 4"x 2-3/4" W/COVER Page 5 TOP VIEW GROMMETED CBLE PSS RIGHT ND LEFT INSIDE PNELS LEFT SHOWN 72" REMOVBLE CCESS COVER (3) OPTIONL SLOPED TOP 12" 3 EQUL SIZED COMPRTMENTS LL POCKET DOORS 44" (3) 6"x 2" 2"x 4"x 2-3/4" SWITCH BOX (7) W/COVER 3' FLUORESCENT LIGHT GROMMETED CBLE PSS 2"DI (2) 20" 76" 3" 19 24" 4"x 4"x 2-3/4" SWITCH BOX LOCK LOCK RER CUTOUTS REMOVBLE PNELS (2) TIE DOWNS NOTES: 1. Electrical, communications and other services shall be provided by general contractor in accordance with facility requirements. SORIC-72 unit shall provide junction boxes as indicated above to facilitate utility services. 2. Cabinet provides an optional removable panel on the rear to facilitate utility routing. It is recommended to have all utilities be delivered from a Junction Box that is mounted behind one of the access panels in the upper compartment or in the lower compartments. 3. Cabinet provides four 4 gang j-boxes to facilitate the main control panel area for user. 4. Shipped as two separate pieces. 5. Seismic applications require specific anchorage. Equipment anchorage provided by others. Calculation specification sheets available from SKYTRON. 24" FRONT VIEW 29" INSIDE CLR. 32" LEVELING FEET 7/8" MIN 2-1/2" MX 30" SIDE VIEW 9/16" 5085 Corp. Exchange Blvd. S.E., Grand Rapids, MI SKYTRON FX TEC-F-0017 REV0 8/10
8 Page 6 OPERTING ROOM INTEGRTION CENTER SORIC-48 2 LIFT & SLIDE POCKET DOORS (TEMPERED GLSS) 4 DJUSTBLE SHELVES 3 FLUORESCENT LIGHT FIXTURE COMPUTER COMPRTMENT COMPUTER COMPRTMENT DJUSTBLE LEVELING FEET (4) INTRODUCTION SKYTRON s SORIC-48 Operating Room Integration Center provides the perfect communications center for PCS and video integration, as well as networking of multiple services within the facility. The SORIC-48 provides a shared hub for information systems distribution within and outside the surgical suite. OPTIONS Standard Phone, Computer and Video Connectors can be provided. Specify type. Control of Lighting, udio, Video, Data and MIS Equipment System operations can be provided as custom applications. RCHITECTURL SPECIFICTIONS Operating Room Integration Center shall consist of a stainless steel cabinet designed to store video, audio and communications equipment. Junction boxes shall be provided for ease of routing electrical, communication and video cabling. Upper compartments have two lift and slide, tempered glass pocket doors, and four adjustable stainless steel shelves. Lower compartment shall include mounting location for SkyVision and a pull-out work surface. Heavy duty, adjustable leveling feet shall be included. Built-in chase shall allow space for up to three 20 mp circuits. Hospital Grade Electrical Receptacles are available for upper and lower compartments.
9 SORIC-48 OPTIONL REMOVBLE BCK PNEL (2) 4 GNG SWITCH BOXES 8"x 4"x 2-3/4" W/COVER Page 7 GROMMETED CBLE PSS RIGHT ND LEFT INSIDE PNELS LEFT SHOWN SIDE PNEL TOP VIEW 48 REMOVBLE CCESS COVER (2) OPTIONL SLOPED TOP 12 2 EQUL SIZED COMPRTMENTS LL POCKET DOORS (2) 6"x 2" CUT OUT 44 3' FLUORESCENT LIGHT "DI (2) GROMMETED CBLE PSS 2 3" 4"x 4"x 2-3/4" KNOCK-OUT CCESS FOR TIE DOWNS 28 INSIDE CLR. 34 TIE DOWN POINTS 9/16 RER CUTOUT TIE DOWNS LEVELING FEET 7/8" MIN 2-1/2" MX FRONT VIEW NOTES: 1. Electrical, communications and other services shall be provided by general contractor in accordance with facility requirements. SORIC-48 unit shall provide junction boxes as indicated above to facilitate utility services. 2. Cabinet provides an optional removable panel on the rear to facilitate utility routing. It is recommended to have all utilities be delivered from a Junction Box that is mounted behind one of the access panels in the upper compartment or in the lower compartments. 3. Cabinet provides four 4 gang j-boxes to facilitate the main control panel area for user. 4. Shipped as two separate pieces. 5. Seismic applications require specific anchorage. Equipment anchorage provided by others. Calculation specification sheets available from SKYTRON. 30" SIDE VIEW 5085 Corp. Exchange Blvd. S.E. Grand Rapids, MI SKYTRON FX TEC-F-0003 REV4 3/11 4
10 Page 8 SORIC-72 TIE-DOWN LOCTIONS Refer to specific seismic calculations if applicable. SKYTRON SORIC-72 TIE-DOWN LOCTIONS KNOCKOUT DETIL SECTION C-C SIDE 11Gx1"x 3" S.S. PLTE C B C B SECTION B-B SECTION - 5" 30" 16" 18-1/2" DENOTES TIE-DOWN LOCTIONS 16" 6-1/2" TOP 9" 72" FRONT C TIE-DOWNS 22-1/2" 25-1/2" C 22-1/2"
11 SORIC-48 TIE-DOWN LOCTIONS Page 9 Refer to specific seismic calculations if applicable. KNOCK-OUT CCESS FOR TIE DOWNS SKYTRON SORIC-48 TIE-DOWN LOCTIONS TIE DOWN POINTS SIDE 11Gx1"x 3" S.S. PLTE 9/16 4 SECTION B-B SECTION - B B B B DENOTES TIE-DOWN LOCTIONS 30" 16" TOP 9-1/8" 11/16" 46-5/8" 48" FRONT
12 5085 Corporate Exchange Blvd. S.E. Grand Rapids, MI FX
RECESSED SolidCare STORAGE CABINETS
TEC-NP-0002 REV0 9/09 RECESSED SolidCare STORAGE CABINETS Weight lbs. kg. Empty 323 (146.51) Loaded 723 (327.92) Crated 438 (198.67) Interior Dimensions 44 7/8"W x 17"D x 55"H 18" 45 3/4" NPRS4818 Recessed
More informationLow-profile, 11U high cabinets hold networking equipment, servers, and phone equipment.
RM140A-R3 RM140A-M-R3 RM145A-R3 RM145A-M-R3 Small Office/Home Office (SOHO) Cabinets Low-profile, 11U high cabinets hold networking equipment, servers, and phone equipment. Fit under most desktops in the
More informationSERVICE PEDESTAL FLOOR-MOUNTED SERVICE PEDESTAL. Installation Manual
SERVICE PEDESTAL Installation Manual FLOOR-MOUNTED SERVICE PEDESTAL Figure 1. DEFINITION OF STATEMENTS Statements in this manual preceded by the following words are of special significance: WARNING: Means
More informationSECTION (Master Template Final-05) ELECTRICAL BOXES. A. Provide boxes for electrical equipment and wiring devices as follows:
SECTION 16130 (Master Template Final-05) ELECTRICAL BOXES PART 1 GENERAL 1.01 SECTION INCLUDES A. Provide boxes for electrical equipment and wiring devices as follows: 1. Wall and ceiling outlet boxes.
More informationLinear Drainage Z886. Perma-Trench. Installation Instructions. 100mm Clear Opening
Linear Drainage Z886 100mm Clear Opening Perma-Trench Installation Instructions Z886 Tools Required Tape Measure Phillips Head Screwdriver Hammer Utility Knife Marker Cordless Drill Reciprocating Saw Ear
More informationREV. 9/08. Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms
REV. 9/08 Mounting Structure PRE-INSTALLATION GUIDE for Ergon Skybooms SKYTRON MOUNTING STRUCTURES for Ceiling Mounted Equipment Foreword Skytron s objective is to provide a program and guideline to assist
More informationZurn Z886. 6" Perma-Trench. Installation Instructions
Zurn Z886 6" Perma-Trench Installation Instructions Z886 Accessories 6" [152mm] Wide Trench Drain System Below are the components of the Z886 trench drain typical to an installation. Check your order to
More informationSERIES SURGICAL LIGHTS
SERIES SURGICAL LIGHTS TEC-B-0012 REV1 Skytron's Aurora LED Surgical Lighting provides advanced bright, cool and color correct illumination to the surgical field and a selectable color temperature of 4,000K
More informationFORM FOOTWALL. FORM FOOTWALL (floating) (floating) Installation Manual
FORM FOOTWALL (floating) Installation Manual FORM FOOTWALL (floating) OVERVIEW The Form is a UL-listed configurable footwall system. This system can include any combination of base cabinets, upper cabinets,
More informationLINEAR DRAINAGE. Z886 Perma-Trench. 6" Perma-Trench Installation Instructions
LINEAR DRAINAGE Z886 Perma-Trench 6" Perma-Trench Installation Instructions Z886 Accessories 6" [152MM] WIDE TRENCH DRAIN SYSTEM Below are the components of the Z886 trench drain typical to an installation.
More informationINSTALLATION MANUAL. FOOTWALL/SINKWALL (floor mount)
INSTALLATION MANUAL FOOTWALL/SINKWALL (floor mount) OVERVIEW The Form is a UL-listed configurable footwall/sinkwall system. This system can include any combination of base cabinets, upper cabinets, wardrobes,
More informationSERIES SURGICAL LIGHTS
SERIES SURGICAL LIGHTS TEC-B-0012 REV1 Skytron's Aurora LED Surgical Lighting provides advanced bright, cool and color correct illumination to the surgical field and a selectable color temperature of 4,000K
More informationAxiom. SURFACE MOUNTED ARRAY Patient Headwall. Installation Guidelines. Installation Instructions.
Axiom www.hsiheadwalls.com SURFACE MOUNTED ARRAY Patient Headwall Installation Instructions Installation Guidelines Tel: 925.427.7800 Fax: 925.427.0800 support@hsiheadwalls.com Hospital Systems Inc. 750
More informationInstallation Manual. Modular Bar Die. Krowne Metal Corporation 100 Haul Rd. Wayne, NJ Toll Free: (800) Fax: (973)
Installation Manual Modular Bar ie Toll Free: (800) 631-0442 Fax: (973) 872-1129 sales@ Modular Bar ie Installation Specifications Bar die structure fabricated out of 16 gauge galvanized steel with stainless
More informationSlimLine Single Threshold Base & Q-Wall-5.1 BASE & BACKWALL INSTALLATION INSTRUCTIONS
SlimLine Single Threshold Base & Q-Wall-5.1 BASE & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For
More informationRisk of fire and electrical shock. DISCONNECT POWER AT ELECTRICAL PANEL before installing or servicing this product.
INSTALLATION INSTRUCTIONS RAIL 2 RM2D T-BAR LED NOTE: The following instructions provide general guidelines for product installation. For additional information consult the applicable electrical codes
More informationNortrax Section David Manchester Road, Ottawa NON-STRUCTURAL METAL FRAMING 16 May 2014 Page 1
16 May 2014 Page 1 PART 1 GENERAL 1.1 DESCRIPTION This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationH50. DYNAMIC BARRIER Bench Fume Hood. Fume Hoods. Installation Instructions. 48"- 60"- 72"- 96" long
Installation Instructions Supreme Air DYNAMIC BARRIER Bench Fume Hood H50 S T Y L E Fume Hoods 48"- 60"- 72"- 96" long Publication No. IIH50-SA 06/01 Part Number: IMAN-H50 Kewaunee Scientific Corporation
More informationINSTALLATION INSTRUCTIONS FOR McDONALDS LED CANOPY FASCIA. Table of Contents
INSTLLTION INSTRUCTIONS FOR McDONLDS LED CNOPY FSCI Table of Contents Important Installer Notes ------------------------------------------------------------------- Page 2 Site specific documents ----------------------------------------------------------------------Page
More informationSEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets
SEISMIC PROTECTION SYSTEMS Bracing Products for Racks & Cabinets Seismic Frame Two-Post Rack Page 11-3 Seismic Protection Products - Racks Page 11-6 Seismic Protection Products - Runway Page 11-8 Seismic
More informationFORM HEADWALL. FORM HEADWALL (floor mount) (floor mount) Installation Manual
FORM HEADWALL (floor mount) Installation Manual FORM HEADWALL (floor mount) OVERVIEW The Form is a UL-listed configurable headwall system. This system includes multiple horizontal equipment channels integrated
More informationPrime Shower Enclosure, Base & Backwall
Prime Shower Enclosure, Base & Backwall SHOWER ENCLOSURE, BASE & BACKWALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior
More informationSECTION NON-STRUCTURAL METAL FRAMING
SECTION 09 22 16 PART 1 - GENERAL 1.1 DESCRIPTION A. This section specifies steel studs wall systems, shaft wall systems, ceiling or soffit suspended or furred framing, wall furring, fasteners, and accessories
More informationSINGLE BOWL SEMI-RECESSED VANITY
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls,
More informationFORM HEADWALL. FORM HEADWALL (floating) (floating) Installation Manual
FORM HEADWALL (floating) Installation Manual FORM HEADWALL (floating) OVERVIEW The Form is a UL-listed configurable headwall system. This system includes multiple horizontal equipment channels integrated
More informationTOLL FREE: (866) VANITY SPECIFICATIONS. VANITY COMPONENTS Model VG09008
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09008 MODEL VG09008 FEATURES Wall-mounted cabinet Soft closing sliding cabinet drawer hardware Cabinet ships assembled PACKING LIST Vanity Brackets - 2 Plastic
More informationCornerview Shower Enclosure & Base
Cornerview Shower Enclosure & Base SHOWER ENCLOSURE AND BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For
More informationDETAIL INSTRUCTION No. 1
BEFORE BEGINNING INSTALLATION, PLEASE READ THROUGH ALL INSTRUCTIONS. Uncrate shipment and check against packing list to insure all materials are included before beginning installation. If any discrepencies
More informationINSTALLATION MANUAL. All Types F Series Rev G
INSTALLATION MANUAL All Types - 1570 F Series Page 1 of 16 TABLE OF CONTENTS DESCRIPTION PAGE GENERAL INFORMATION & ADVISORIES 2 PRODUCT INFORMATION 3 GET TO KNOW YOUR CBU 4 HARDWARE AND COMPONENTS 5 CONCRETE
More informationImpression Graphic panels
Impression Graphic panels Installation Guidelines 6003.I Rev. 02 8/15 Please Read Disclaimers: PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION!! These guidelines are provided in good faith to
More informationPRE-INSTALLATION GUIDE
TRUMPF MEDICAL SYSTEMS Inc. Charleston, SC PRE-INSTALLATION GUIDE FOR CEILING MOUNTED EQUIPMENT MANAGEMENT SYSTEMS, SURGICAL / EXAM LIGHTS, AND FLAT PANELS EMS and Light Pre-installation Guide File: 110720
More information4 Double Hooks on a Board
4 Double Hooks on a oard ssembly Instructions - Please keep for future reference 875/5292 875/5340 Dimensions Width - 45.7cm Depth - 7cm Height - 0.5cm Important Please read these instructions fully before
More informationPrime Shower Enclosure & Base Kit
Prime Shower Enclosure & Base Kit SHOWER ENCLOSURE AND SHOWER BASE KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLine TM reserves the right to alter, modify or redesign products at any time without prior
More informationPrime Shower Enclosure & Base
Prime Shower Enclosure & Base SHOWER ENCLOSURE & BASE INSTALLATION INSTRUCTIONS IMPORTANT DreamLine reserves the right to alter, modify or redesign products at any time without prior notice. For the latest
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking (See specific caulking recommendations) caulking gun shims tape measure 1/8 drill bit Phillips screw driver
More informationH07 H09. BENCH FUME HOOD with Combination Sash. Fume Hoods. Installation Instructions. 48"- 60"- 72"- 96" long
Installation Instructions Supreme Air BENCH FUME HOOD with Combination Sash H07 H09 S T Y L E Fume Hoods 48"- 60"- 72"- 96" long Publication No. IIH07-SA 07/06 Part Number: IMAN-H07 FUME HOOD END PANEL
More informationInigo Console Table INSTALLATION INSTRUCTIONS P74300, P A Page 1 of 5
P74300, P74301 Page 1 of 5 THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista product.
More informationMulti-Piece EasyStep Product Installation Instructions
Tools/materials you might need for proper installation 6D galvanized screws caulking gun shims tape measure 1/8 drill bit Phillips screw driver cardboard china marker (or grease pencil) furring strips
More informationThis Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols.
VIGO INDUSTRIES INSTALLATION GUIDE FOR STANDING SHOWER CABIN (MODEL VG06062) SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the
More informationSection 7: Specifications
Section 7: Specifications 29 31 Building Boundary of Clear Area See Note # 1 8' Shrubs 8' Concrete Pad Equipment 8' TRAVELED WAY M Meter Pedestal 8' Curb Protective Vehicle Posts (Bollards) If Required
More informationPC-PH SERIES BTUH
C O M I T A L E N A T I O N A L I N C. PC-PH SERIES 7000 18000 BTUH Installation Instructions Comitale National Inc. 1683 B Winchester Road Bensalem, PA 19020 215-244-9650 Fax: 215-244-9679 email: sales@comitalenational.com
More informationOther HEMCO Products. HEMCOR Lab Planning Solutions. Installation, Operation, Maintenance Manual. HEMCO ModuLab
Other HEMCO Products Installation, Operation, Maintenance Manual HEMCO ModuLab Made In The U.S.A. UniFlow CE UniFlow SE AireStream High Performance Energy Efficient Laboratory Fume Hoods UniFlow LE SEFA
More information1. Hangers and supports for electrical equipment and systems.
PART 1 - GENERAL... 1 1.1 RELATED DOCUMENTS... 1 1.2 SUMMARY... 1 1.3 DEFINITIONS... 1 1.4 PERFORMANCE REQUIREMENTS... 1 1.5 SUBMITTALS... 2 1.6 QUALITY ASSURANCE... 2 1.7 COORDINATION... 2 PART 2 - PRODUCTS...
More informationC.R. LAURENCE CO., INC. Intelli-Track SPS. Phase One - Installation Instructions
Tools and Supplies: C.R. LAURENCE CO., INC. Intelli-Track SPS Phase One - Installation Instructions Ratchet Wrench with 4" Extension 9/16" Open-End Wrench (two required for suspension mounting) 9/16" Hex
More informationWAKE UP DESCRIPTION ORDERING INFORMATION SAFETY: WARNINGS T01-E INSTALLATION INSTRUCTIONS MIRRORS K-13013T/K-13014T/K-13015T
WAKE UP INSTALLATION INSTRUCTIONS MIRRORS K-303T/K-304T/K-305T BEFORE YOU BEGIN Warning! Risk of personal injury and product damage. Mirrored cabinets are very heavy and should not be lifted or installed
More informationSINGLE BOWL VESSEL VANITY
BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing bathroom fixtures and plumbing. Signature Hardware accepts no liability for any damage to the floor, walls,
More informationDouble Tidy Rail. Assembly Instructions- Please keep for future reference. Important - Please read these instructions fully before starting assembly
Double Tidy Rail ssembly Instructions- Please keep for future reference 87198 Dimensions Width - 89cm Depth - 8cm Height - 101/17cm Important - Please read these instructions fully before starting assembly
More informationINSTALLATION MANUAL RECTANGULAR COLUMN
INSTALLATION MANUAL RECTANGULAR COLUMN Model # 5502 OVERVIEW The Rectangular Column is a UL-listed, multi-sided, vertical hospital modular service assembly. This system uses vertical and/or horizontal
More informationQuick-release pins swing the rack open from left to right to simplify installing and maintaining your equipment.
RM070A-R3 RM080A-R3 Wallmount Frame User s Manual Quick-release pins swing the rack open from left to right to simplify installing and maintaining your equipment. Customer Support Information Order toll-free
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationSECTION METAL ATHLETIC LOCKERS
SECTION 10 51 13 - METAL ATHLETIC LOCKERS PART 1 GENERAL 1.1 SECTION INCLUDES A. DESCRIPTION: Furnish and install factory-assembled Heavy-Duty MIG-Welded Metal Lockers, complete, as shown and specified
More informationThermaSteel Corporation ASSEMBLY MANUAL
ThermaSteel Corporation ASSEMBLY MANUAL TABLE OF CONTENTS 1- INTRODUCTION 1.1 THERMASTEEL TM WALL PANELS 1.2 Drawing and Element Numbers 2- ASSEMBLY 2.1 Sequence of Assembly 2.2 Preparation of Foundation
More informationINSTALLATION INSTRUCTION (U.S.A) FOR LUMI-O DRY NICHE INGROUND LIGHT.
www.lumi-o.com INSTALLATION INSTRUCTION (U.S.A) FOR LUMI-O DRY NICHE INGROUND LIGHT. STANDARD & L.E.D. Lumi-O Industries Inc. 370 Lajeunesse O. St-Jerome QC J7Y 4E5 tel (450)565-5544 * 1-866-99LUMI-O (450)565-5958
More informationInstallation. Smart-UPS VT in Parallel kva 380/400/415 V 208/220 V 200/208 V
Installation Smart-UPS VT in Parallel 10-40 kva 380/400/415 V 208/220 V 200/208 V Contents Safety... 1 IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS.............................. 1 Prepare for
More informationSECTION PLASTIC-LAMINATE-CLAD COUNTERTOPS
SECTION 12 3623.13 - PLASTIC-LAMINATE-CLAD PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationModular CABANA Kit 16 x 16 (6x6) Lumber: Western Red CEDAR #1 (Cabinet) Shingles: 5X / 16" long / 1/2" thick or 16 oz. copper
Lumber: Western Red CEDAR #1 (Cabinet) Shingles: 5X / 16" long / 1/2" thick or 16 oz. copper Modular CABANA Kit 16 x 16 (6x6) Hipped Roof & Build-in Transoms Entry Key Lock Set (bright brass or dark bronze)
More informationInstallation Manual. Retractable Ceiling Column Models 8301 & 8301PC
Retractable ceiling column Installation Manual Retractable Ceiling Column Models 8301 & 8301PC Overview The Retractable Ceiling Column is a convenient and cost-effective way of supplying medical gas and
More informationPower Electronics, Inc. Packaged Equipment Center Standard Construction and Design Features
DESIGN CRITERIA FOR STANDARD CONSTRUCTION: These standard design elements of the P.E.I. Power Equipment Center are utilized to meet the following design criteria per ASCE 7-05 as adopted by the IBC (International
More informationGuardian Wall Panel Installation Manual
Guardian 275 4 Wall Panel Installation Manual Guardian 275 4 Wall Panel Installation Manual This instructional manual provides General Installation Instruction. Installers should refer to the "as-built"
More informationInstallation Guidelines for Sealing PTAC Sleeves
www.quakerwindows.com www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines for Sealing PTAC Sleeves Read these instructions
More informationUtility Cabinet System (UCS)
(UCS) The Ultimate in Stainless Steel Modular Walls UCS: Eliminates the need and the costs of constructing a traditional wall Provides easier access and faster installation of the utilities compared to
More informationPreference Slimline 5537 Utility Console I NSTALLATION GUIDE
Preference Slimline 5537 Utility Console I NSTALLATION GUIDE WARNING Failure to install the 5537 as described in this installation guide may cause the unit to collapse, resulting in serious injury to personnel.
More informationInstallation Guidelines for all Quaker products with nail fins New construction nail fin installation with a drainable weather resistant barrier.
www.quakerwindows.com www.quakercommercialwindows.com PO Box 128 504 Highway 63 South Freeburg, MO 65035 800-347-0438 573-469-4151 (fax) Installation Guidelines for all Quaker products with nail fins New
More informationFIXED CEILING COLUMN. Installation Manual FIXED CEILING COLUMN
FIXED CEILING COLUMN Installation Manual FIXED CEILING COLUMN INTRODUCTION Location, sequence of services and orientation of Surgical Ceiling Columns are specified on the building plans. Be certain installation
More informationINSTALLATION MANUAL KOCH
INSTALLATION MANUAL KOCH TECHNICAL SYSTEMS GROUP PRE-FAB ACOUSTICAL/THERMAL PANELS AND ENCLOSURES GEORGE KOCH SONS, LLC TECHNICAL SYSTEMS GROUP 10 South Eleventh Avenue Evansville, Indiana 47744 812-465-9600
More informationAegis Heavy Capacity 20K Floor Scale. MODEL: 6200 Series. Installation Manual
Installation Manual Aegis Heavy Capacity 20K Floor Scale MODEL: 6200 Series Copyright 1997-2014 Fairbanks Scales, Inc. Revision 3 50637 All Rights Reserved 07/14 Aegis Heavy Capacity 20K Floor Scale Model:
More informationSECTION STEEL HEALTHCARE CASEWORK
SECTION 12 35 70.01 STEEL HEALTHCARE CASEWORK This guide specification has been prepared by InnerSpace Corporation to assist design professionals in the preparation of a specification section covering
More informationSECTION CONDUITS AND BACKBOXES FOR COMMUNICATIONS SYSTEMS
SECTION 16711-27 05 28.33 PART 1 - GENERAL 1.01 SUMMARY A. This section includes Labor, materials and equipment necessary to complete the installation required for the items specified under this Section,
More informationM-SERIES INSTALLATION
M-SERIES INSTALLATION Connectivity with flexibility For more product information visit connectrac.com, call us at 877-480 - 5637 or email us at info@connectrac.com ADA COMPLIANT - U.L. TESTED AND LISTED
More informationSECTION OUTLET, PULL, AND JUNCTION BOXES
SECTION 16131 OUTLET, PULL, AND JUNCTION BOXES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 09900 - Painting. 2. 16112 - Raceways and Conduits. 1.02 SYSTEM DESCRIPTION A. Performance Requirements:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TEC-B-0136 REV0 04/15/15 AUA SERIES SURGICAL LIGHTS (STANDARD RADIAL ARM MODELS ONLY) Read this manual before starting to work! This information is necessary for the safe and
More information6032 SH 3P Residential Shower Installation Instructions Gelcoat & Solid Surface Bathware
Tools/materials you might need for proper installation 6D galvanized screws 100% silicone caulking caulking gun acrylic latex caulk shims tape measure 1/8 drill bit Phillips screw driver cardboard china
More informationINSTRUCTIONS FOR ASSEMBLING NEBS FLOODED RACKS
INSTRUCTIONS FOR ASSEMBLING NEBS FLOODED RACKS Publication No. US-NEBS-IM-003 September 2013 INSTRUCTIONS for ASSEMBLING NEBS FLOODED RACKS Read all instructions carefully and observe all warnings before
More informationDIVISION 10 SPECIALTIES SECTION METAL LOCKERS
DIVISION 10 SPECIALTIES SECTION 10 51 13 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationEXPRESS5800/1080Xd. Installation Procedures
EXPRESS5800/1080Xd () Installation Procedures Proprietary Notice and Liability Disclaimer The information disclosed in this document, including all designs and related materials, is the valuable property
More informationINSTALLATION MANUAL PROVIDER PLUS
INSTALLATION MANUAL PROVIDER PLUS OVERVIEW The Provider Plus is a UL-listed, surface-mounted, horizontal modular headwall assembly. This system uses one or more horizontal component tiers to locate services
More informationMODEL: ASCEND SIT/STAND COMMAND CENTER CONSOLES
2015 WINSTED CORPORATION EMAIL: info@winsted.com WEB: winsted.com TEL: 800.447.2257 or 952.944.9050 FAX: 800.421.3839 or 952.944.1546 10901 Hampshire Ave. So. Minneapolis, Minnesota 55438-2385 U.S.A 1)
More informationDIVISION 26 RACEWAYS AND BOXES FOR ELECTRICAL SYSTEMS PART 1 - GENERAL RELATED DOCUMENTS
PART 1 - GENERAL 01.01 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification sections, apply to work of this Section.
More informationUS Pool Lift Model #114 (Independence) Installation Guide
US Pool Lift Model #114 (Independence) Installation Guide This manual has been provided to assist with lift installation. For further assistance please contact your authorized US Pool Lift dealer. Toll
More informationSCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
More informationSECTION MOTOR CONTROL CENTER
SECTION 16445 MOTOR CONTROL CENTER PART 1 GENERAL 1.01 DESCRIPTION A. This section covers the contract item Motor Control Center (MCC). The contract item includes demolition and removal of existing MCC;
More informationSYSTEM 600 BILL CHANGER INSTALLATION INSTRUCTIONS Congratulations...
www.standardchange.com 1-800-968-6955 Technical Phone Support is from 8:00AM to 7:30PM E.S.T., Monday-Friday Walk-in Service is from 8:00AM to 4:30PM E.S.T., Monday-Friday Parts Department is from 8:00AM
More informationLIFT FRONT CURVED GLASS HOT FOOD/DELI MERCHANDISERS Hot Temperature Service Display Cases
Installation & Service Manual LIFT FRONT CURVED GLASS HOT FOOD/DELI MERCHANDISERS Hot Temperature Service Display Cases Save the Instructions in this Manual for Future Reference!! This merchandiser conforms
More informationInstallation Guide Single-Hung, Picture & Shapes Non-Impact & Impact Resistant Florida Flange Windows
Non-Impact & Impact Resistant Florida Flange Windows americancraftsmanwindows.com Project Requirements: Read guide before starting installation. Read all warnings and cautions during installation. Check
More informationSECTION (06415) - PLASTIC COUNTERTOPS
PART 1 GENERAL 1.01 SUMMARY A. Section Includes: SECTION 12 36 23 (06415) - PLASTIC COUNTERTOPS 1. Plastic Laminate a. Countertops and Backsplashes b. Aprons B. Related Sections: 1.02 REFERENCES 1. Section
More informationWall-Mount & Back to Wall Toilets
Wall-Mount & Back to Wall Toilets Installation Guide FLOOR LW600 back to wall LW600 wall-mount FLOOR 05-04 Attention Before Installation If you are installing this product in a new construction or remodel,
More informationLeveling Foot RB210. Leg Extender RLT66
Landing for Right & Left Turn R342 ITEMS # 0254049, 0254061, 0254072, 0254076, 0016567, 0254099, 0254110, 0054116, 0254117, 0254126, 0254140, 0254150, 0254156 CUSTOM ACCESS RAMP SYSTEM MODELS # R100, R242,
More informationINSTALLATION GUIDE PLEASE READ ENTIRE INSTRUCTION MANUAL BEFORE PROCEEDING!
DURA - TRENCH INSTALLATION GUIDE This guide is intended to aide in the installation of Dura-Trench systems. There are many different applications and situations for the use of this product and the installation
More informationWeep Valves Stucco Wire Mesh Reinforcement Weather Resistive Barrier Sheathing Insulation Framing
INSTALLATION INSTRUCTION FOR SINGLE-HUNG AND FIXED WINDOW REPLACEMENT using FLUSH FLANGE Installation Instructions for replacing windows in a Typical Stucco Application. These instructions were developed
More informationA. Provide a complete Distribution Panelboard system as indicated on the drawings, and as specified herein.
16470 PANELBOARDS ************************************************************************************************************* SPECIFIER: CSI MasterFormat 2004 number: 26 24 16 An optional keynote to
More informationMounting Screw. Channel Filler. Light Angle Adjustable Screw. LED Board Vertical stud and blocking Locking Nose. Driver.
The Knife Edge Cove is a modular lighting system consisting of two parts: 1- An aluminum fixture housing extrusion 2- Drop-in lighting modules The fixture will provide a continuous knife edge architectural
More informationNORTHWESTERN UNIVERSITY PROJECT NAME JOB #
SECTION 26 0529 - HANGERS AND SUPPORTS FOR ELECTRICAL SYSTEMS PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and
More informationInstallation Guide DROP-IN OR FREESTANDING CAST IRON BATH. English page T01-B
Installation Guide DROP-IN OR FREESTANDING CAST IRON BATH 368 201419 English page 1-8 9-15 Before You Begin A. Introduction Please read these instructions carefully to familiarize yourself with the required
More informationPC-PH SERIES 2 TON. Installation Instructions
C O M I T A L E N A T I O N A L I N C. PC-PH SERIES 2 TON Installation Instructions Comitale National Inc. 1883 B Winchester Road Bensalem, PA 19020 2115-244-9650 Fax: 215-244-9679 email: sales@comitalenational.com
More informationEXIRA EXPOSED PIPE SHOWER INSTALLATION
SKU(s): 923583 EXIRA EXPOSED PIPE SHOWER INSTALLATION BEFORE YOU BEGIN We recommend consulting a professional if you are unfamiliar with installing plumbing fixtures. Signature Hardware accepts no liability
More informationINSTALLATION MANUAL SURFACE-MOUNTED HEADWALL
INSTALLATION MANUAL SURFACE-MOUNTED HEADWALL Model # Series 7200-S Top Mounting Plate Electrical Junction Box Located Behind Removable Upper Panel Medical Gas Connections Lower Mounting Plate OVERVIEW
More information5485HT 5650H 5660H 5660HTS 5665HTS Instruction Kit Same Deutz-Fahr Flow Sensor 5SW models Flow Sensor 6SW models
Note: Indented items indicate parts included in an assembly listed above Quantity by Model Part Name/Description Part Number 5485HT 5650H 5660H 5660HTS 5665HTS Instruction Kit Same Deutz-Fahr 4101102 1
More informationMODEL: SLAT-WALL COMMAND CENTER CONSOLES
2015 WINSTED CORPORATION EMAIL: info@winsted.com WEB: winsted.com TEL: 800.447.2257 or 952.944.9050 FAX: 800.421.3839 or 952.944.1546 10901 Hampshire Ave. So. Minneapolis, Minnesota 55438-2385 U.S.A MODEL:
More informationZurn Z874. Trench Drain System. Installation Instructions
Zurn Z874 Trench Drain System Installation Instructions Z874 Accessories Trench Drain System Below are the components of the Z874-X trench drain typical to an installation. Check your order to verify you
More information