DILLARD S TEST PROTOCOL FOR DILR-1102-US BED CANOPY (V25)

Size: px

Start display at page:

Download "DILLARD S TEST PROTOCOL FOR DILR-1102-US BED CANOPY (V25)"

Stanley Rice
5 years ago
Views:

Test Date: Reviewed By/Date: SUPPLEMENTAL PROTOCOLS *CA Prop 65 Applicable Section from Protocol MC-6572-US DILLARD S TEST PROTOCOL FOR 1 The sample shall be reviewed against the requirements of

Note: Additional cost, sample size & TAT may be required if testing to 1 or more supplemental protocols is necessary.

1 Test Date: Reviewed By/Date: SUPPLEMENTAL PROTOCOLS *CA Prop 65 Applicable Section from Protocol MC-6572-US DILLARD S TEST PROTOCOL FOR 1 The sample shall be reviewed against the requirements of California Proposition 65 to determine if additional testing or labeling is required. Note: Additional cost, sample size & TAT may be required if testing to 1 or more supplemental protocols is necessary. Please refer to the above referenced supplemental protocol(s) for additional information. LABELING One Time Use Products **Fair Packaging and Labeling Act OR All Other Products **Uniform Packaging and Labeling Regulations F.P. & L. Act (16 CFR 500) OR NIST Uniform Laws and Regulations Handbook Manufacturer, Packer, or Distributor s Name & Address (City, State & Zip) Product Identification Net quantity of contents shall be expressed in terms of weight or mass, measure, numerical count, or combination so as to give accurate information to facilitate consumer comparison (U.S. and metric units). **Country of Origin Marking 19 CFR Shall indicate country of origin legibly, permanently, and in comparable size and close proximity to any mention of country other than country in which the article was manufactured or produced. Must be visible at point of purchase. Use Labeling H Use/care instructions that are clear and understandable shall be provided in language appropriate to destination countries. Size/Dimensions FTC All Size designation of the mattress/bed it is intended to fit (Twin, Full, Queen, King, etc.). Fiber Content 16 CFR 303 All Report actual (Textile fiber products identification act) Care label 16 CFR Verify present. Mock up label is accepted. Note: please refer to testing results on Page 1 of report for confirmation of the proper care. If the lab analysis does not match the affixed or proposed label, then the label will fail. Country of Origin 19 CFR All Report actual RN# (Registered Number) or H-1057 All Verify Presence (Textile Fiber Products Identification Act) Manufacturer Name Verify Label Claims H-1057 All Must comply to claims Page 1 of 5

2 ANALYTICAL *Total lead content in surface coatings CPSC-CH-E / CPSD-AN MTHD 1 All accessible surface coatings on the product shall not contain lead or lead compounds in which the lead content is in excess of 0.06% (600 mg/kg) of the weight of the total content. * Formaldehyde spot test on textile Qualitative analysis / CPSD-AN MTHD * Formaldehyde release in textile AATCC 112 / CPSD- AN MTHD Fabric, which may come into contact with skin, shall be negative result. Note: - This method cannot be applied on nylon and PU, quantitative analysis should be performed directly if need. Fabric, which may come into contact with skin, shall not have formaldehyde release exceed 75 mg/kg (ppm). Note: conduct testing only if formaldehyde spot test shows positive result. PHYSICAL CHARACTERISTICS *Fiber Content AATCC 20 / 20A 2 FTC Requirements Blends: Report actual (3% Maximum Tolerance) Single: Report actual (0% Tolerance) Fabric Weight (Oz. / Sq. yd) ASTM D ae1 3 Report actual (±5%) Fabric Construction Visual 1 Report actual Dimensions H Report overall dimensions; shall meet label claims (If applicable). CONSTRUCTION & H-1057 All No major defects, no sharp edges, even construction, WORKMANSHIP even print / design if applicable. Hanging Device Reinforcement H As specified PERFORMANCE Functionality / Ease of Assembly Actual Use / H Shall provide ease of assembly, instructions shall be accurate and easy to follow C: R: Page 2 of 5

3 *Flammability ASTM D Must comply *DIMENSIONAL STABILITY: Laundering (3 HL):or Dry Cleaning (1DC) (If applicable) STRENGTH FOR WOVEN: AATCC 135 / 150 / % x -3.0% (Length x Width) Fabric Weight (Oz. / Sq. Yd) Fabric Weight (oz/sq yd) < >4.0 Tensile Strength ASTM D R (Warp & Fill, Lbs. / In., Minimum) Tear Strength ASTM D (Warp & Fill, Lbs. Minimum) 09R2013e1 Seam Strength (Warp & Fill, Lbs.) ASTM D e FOR KNIT: Bursting strength of textile fabrics: diaphragm method PSI, Minimum) Strap Seam Strength at Frame (Lbs.) *Attachment Strength (Hanging device loop or strap, any decorative trim) COLORFASTNESS ASTM D Lbs. ASTM D e Lbs. ASTM F Section 8.9 (Mod.) *Dry-Cleaning (1X) (If Applicable) AATCC 132 Per Care Label *Actual Home Laundering AATCC 135 / 150 (If Applicable) Per Care Label 2 15 Lbs. for 10 seconds Mod. = Citation not specific to the product. 1 Color Change: Grade 4 Minimum Self Staining: Grade 4.5 Minimum 1 Color Change: Grade 4 Minimum Self Staining: Grade 4.5 Minimum Staining: Grade 3 Minimum Page 3 of 5

4 Crocking AATCC 8-16 / Dry Crocking: Reactive, Disperse, Acid Dyes: Grade 4 Minimum Vat, Sulfur, Pigment, Direct Dye: Grade 3 Minimum Brushed / Sanded Surfaces: Grade 3 Minimum Wet Crocking: Reactive, Disperse, Acid Dyes: Grade 3 Minimum Vat, Sulfur Dye: Grade 1.5 Minimum Pigment, Direct Dye: Grade 2 Minimum Brushed / Sanded Surfaces: Grade 2 Minimum APPEARANCE PROPERTIES General Appearance (3 HL Or 1 DC) Visual 1 No visual defects or excessive color or surface change (Grade 4 min), No open seams or detached trims Light AATCC [Option 3] Grade 20 hours *Chlorine Bleach (If applicable) S Grade 4 Minimum *Non-Chlorine Bleach S Grade 4 Minimum (If applicable) *Ozone (for white) AATCC Grade 4 Minimum (1 cycle) *Burnt Gas (for white) AATCC 23 1 Grade 4 Minimum (1 cycle) Key: * Additional Charge For This Test ** Mandatory Requirement Results Key: Rating Key: M Meets NM Does Not Meet Good Good NA Not Applicable NT Not Tested Marg. Marginal C Claimed R Recorded Fail Fail No. Of Required For Complete Testing: 3 No. Of (Fully Packed) Cartons For Transit Testing: 1 (Only Upon Dillard s Request) Creation Date: October 14, 2005 No. Of Working Days For Complete Testing: 7 Editorial Revision Date: FEBRUARY 13, 2018 Pricing Review Date: October 17, 2005 Technical Review Date: Page 4 of 5

5 Page 5 of 5 BV Lab Number:

DILLARD S TEST PROTOCOL FOR DILR US DECORATIVE PILLOWS / STUFFED ITEMS (V26)

DILLARD S TEST PROTOCOL FOR DILR US DECORATIVE PILLOWS / STUFFED ITEMS (V26) Test Date: Reviewed By/Date: SUPPLEMENTAL PROTOCOLS * California Proposition 65 Applicable Section from Protocol CPSD-AN-PTCL- 06572-US *Law label (bedding tag). DILR-SL-PTCL-01990- DILLARD S TEST PROTOCOL