Fastening of Facade. Insulation
|
|
- Ralf Shields
- 5 years ago
- Views:
Transcription
1 Fastening of Facade Insulation
2 Primary Principles in the Use of Mechanical Connectors in the Technology of the Wall Barrier Insulation Load Transmission: From the influence of weather conditions (primarily the wind but also temperature differences). From the lap-shear strength resulting from the dead load of the insulation system. From the adhesive setting weakening in the course of time as a result of thermal impacts (thermal expansion of the cladding panel). Mechanical fixing of thermal-insulation panels: Owing to the panel s fixing, the system is more resistant to dynamic impacts. Elimination of errors when preparing bases for thermal-insulation panels to be adhered: Inappropriate amount of an adhesive. An adhesive of poor quality and little resistance to ageing as a result of the impact of low temperatures. Inappropriately prepared base; old and non-resistant plaster or remaining old layers of the façade s finishing, exceedingly great unevenness of the surface. Failure to follow strict technological requirements such as time of the adhesive s setting on a cement base). Failure to provide the recommended ambient temperature (producers of adhesives most often recommend temperatures between +5 o C and +25 o C). Works left unfinished in winter. Selection of Connectors: Connector with a Metal or Plastic Spindle Connectors with plastic insert pins are suitable for fastening of the insulation made of light materials such as polystyrene foam. Connectors with a metal insert pin are suitable for fastening of all types of the thermal insulation and are intended for such materials as mineral wool, lamella wool, cork panel, recycled insulation materials. Depth of securing anchor area The anchor area of connectors depends on the type of material, which a wall is made of. The most common division of substrate is in accordance with the guidelines of the European Technical Approval ETAG 014. Depth of anchoring is provided each time for particular groups of connectors. Connector s Length When selecting the length of a connector, the following constituents should be taken into consideration: Length of anchoring provided by the Koelner s connector producer. The adhesive s thickness under an insulating plate including possible old layers (old plaster, etc.). Thickness of the insulating material. g b d h L length of connector L = d + b + g h = g + 1 cm d thickness of insulation material b thickness of an adhesive with possible old plaster and unevenness g anchoring depth h depth of the hole s drilling ceramic hollow brick adhesive polystyrene foam 2
3 Number and Placement of Connectors The number and placement of connectors is one of the most important parameters determining the durability and safe usage of a facade. The following factors determine the connectors number and placement: Weight of the insulation system. Type of the thermal-insulation material. Height of an insulated building. Area of influence of wind forces. Pull out strength of single connectors in relevant types of a base (available in Technical Approvals). Boundary Area The building s corners are especially exposed to the influence of wind forces. The socalled boundary area is defined to have 1/8 of the building s shorter dimension and is contained in the range of 1 to 2m. 1m< 1 8 A<2m A Placement of Connectors Examples of Connectors Number and Placement 6 pieces/m 2 4 pieces/m 2 6 pieces/m 2 4 pieces/m 2 Type of Connector KI-10 TFIX-8 KI-10M TFIX-8M TFIX-8ST KI-10N KI-10NS KC, KIG Polystyrene Foam Building s Height/Number of Connectors up to 8m 8m-20m over 20m pieces/m 2 pieces/m pieces/m 2 pieces/m 2 pieces/m 2 8,5 pieces/m 2 6 pieces/m 2 11 pieces/m 2 8 pieces/m 2 Type of Connector KI-10M TFIX-8M TFIX-8ST KI-10N KI-10NS KC, KIG Mineral Wool Building s Height/Number of Connectors up to 8m 8m-20m over 20m pieces/m 2 pieces/m 2 pieces/m 2 14,5 pieces/m 2 10 pieces/m 2 17 pieces/m 2 12 pieces/m 2 Lamella wool Building s Height/Number Type of Connector of Connectors up to 20m over 20m KI-10M TFIX-8M 4 pieces/m 2 4 pieces/m TFIX-8ST 2 + KWL KI-10N 7 pieces/m 2 10 pieces/m 2 KI-10NS KC, KIG 7 pieces/m 2 4 pieces/m 2 10 pieces/m 2 4 pieces/m 2 3
4 BASIC RANGE Connector s Name KI-10 KI-10NP KI-10M KI-10N KI-10NS KI8M-D INSULATION MATERIAL Traditional Polystyrene Foam/Extruded Panels Mineral Wool Lamella Wool + Clamping Flange Cork Panels Wood Fibre Panels, Light Panels Made of Recycled Material * * Concrete Full Brick, Calcium Silicate Brick, Concrete Blocks, Stone BASE Cellular Brick, Cavity Brick, Structural Clay Tiles Blocks Made of Light Concrete Such As Gravelite Concrete Autoclaved Cellular Concrete (Aerated Concrete) Wood, Wood-Based Boards Available Lengths [mm] 70, 90, 120, 140, 160, 180, 200, , 160, 180, 200, , 90, 120, 140, 160, 180, 200, 220, , 140, 160, 180, 200, 220, 240, 260, 300, , 160, 180, 200, 220, 240, 260, 300, 340 Diameter of a Drilling Opening [mm] , 110, 130, 150, 170, 190, 210, , 270, 290 Anchoring Depth PROPERTIES Fastening Variant Hammered-In Hammered-In Hammered-In Hammered-In Screwed-In Hammered-In Reference Documents Additional Information: AT /98 + Appendix no. 1, ETA 07/0291 ETA under preparation The most popular connectors for fastening traditional and extruded polystyrene foam AT /98 + Appendix no. 1, ETA under preparation *Due to diffusion resistance of polystyrene foam and the connector, the latter is not recommended for newly constructed walls; discolouring on plaster may appear AT /2005, ETA 07/0221 AT /2005, ETA 07/0221 Connector for bases being the most problematic. Screwed-in variant is recommended especially for wide sections of insulation fastened to porous materials such as porous ceramic hollow bricks and the lightest variety of aerated concrete. ETA-06/0191 Increasingly high thermal-insulation and durability properties. Connector preferred by producers of insulation systems. 4
5 TFIX-BSO RANGE ADDITIONAL PRODUCTS TFIX-8 TFIX-8M KI-8M KIK KIG / UC KC / UC 90, 110, 130, 150, 170, , 95, 115, 135, 155, 175, 195, 215, 235, 275, , 110, 130, 150, 170, 190, 210, 230, 250, 270, , 90 KIG: UC: 50, 60, 70, 80, 90, , 35 Hammered-In Hammered-In Hammered-In Hammered-In Screwed-In Screwed-In AT /98 + Appendix no. 1, ETA under preparation ETA-07/0336 AT /98 + Appendix no. 1 AT /2005 ETA under preparation AT /2006 Connectors of increased thermal-insulation properties Connectors of increased thermal-insulation properties For fastening of polystyrene foam and wool on small surfaces such as window and door openings. For walls made of wood and wood-derived panels such as OSB 5
6 Installation Recommendations The mechanical installation of insulation panels should take place after adhering them in accordance with recommendations of the manufacturer of an adhesive intended for the insulation panel s fastening. The adhering process requires typically hours of a service interruption for the adhesive to set. Then, the connectors can be fastened. When fastening, it is important to match the diameter of the connector s sleeve with the drill bit s diameter and the type of the base determining whethera rotary hammer should be used. In the case of works performed in low temperatures or in rain, no restrictions are known. However, producers of insulation systems condition that works should be performed at the minimum of +5 C. The fastening of insulation panels is one of the stages of the system s construction and cannot exceed the range of temperatures; that is why the similar temperature is assumed. Base Preparation The base should be dusted. All remaining layers and coats should be removed. In the case of a new building, the base should be robust enough to support big loads and intervals between the phases of installation process should be provided. Installation of Fixing Profiles Set a fixing profile horizontally by means of a level, then mark a reference line and spots for drilling. Drill openings in previously marked spots. Match the drill s diameter with the applied connectors for the installation of the profile; the connectors recommended placement for the installation of the profile is ca. 50 cm. If the base is uneven, rectification performed by means of spacers is recommended. Connectors for board laths are recommended for connecting the profiles. Cut the fixing profiles at the angle of 45 degrees in internal and external corners. 6
7 Fastening of Connectors Once the insulation panels are adhered according to the recommendations of the panels and the insulation systems producers, especially the producers of adhesives for insulation panels, mechanical connectors can be fastened, maintaining service interruption (lasting typically hours). The drill bit s diameter should match the connector sleeve s diameter, which is 8 or 10 mm. Rotary hammers are not recommended for drilling in porous materials (aerated concrete, porous ceramic materials) and cavity walls (ceramic hollow bricks of thin sides). An opening should be drilled approximately 10 mm deeper than the indicated anchoring depth, in order to leave room for possible drill dust. Once an opening is drilled, set a connector inside and hammer or screw it in (depending on its type), so the disc s surface touches the insulation material. Worn-out drill bits should not be used, especially for hard materials (concrete, full brick), for it hampers and even prevents from fastening of connectors. In the case of the so-called lamella wool, pressure plates should be used. The number and placement of bolts should be performed according to building heights diagrams. Complementary Elements Finishing of window and door openings single-element connector KIK is the fastest connector for such a purpose; it is fastened by hammering in an opening which was prepared previously. PVC and aluminium corners with a mesh should be placed in the building s corners and dipped in the adhesive by means of a notched trowel as shown on the photo. 7
8 An expansion bead for building expansion joints. The profile should be inserted in a dilatation opening and the mesh dipped in an adhesive intended for dipping the reinforcing mesh. The dilatation opening should not be filled with the resin compound intended for dipping a mesh special compounds resistant to UV rays are recommended for this purpose. A drip bead for rainwater disposal from the facade should be used above window and door openings. Stick a window trim to the window framework. Then, remove a paper strip (as shown on the photo) and adhere the protective film. The film with the strip should be removed once the insulation works are completed, i.e. after the thin-coat plaster is spread. Final Remarks The long-term laboratory research and practice of the use of connectors allowed Koelner Company to develop an appropriate shape for the anchoring area so as to achieve maximal values of forces transferred on a base. Due to the use of plastics of the highest quality the connectors have appropriate hardness. Spraying of metal spindles was designed so as to reduce thermal bridges. The openings in the connector s disc allow for comfortable dipping in an adhesive with little loss of the disc s rigidity. However, fastened connectors will serve their intended function if the principles of their selection, installation, and the use of the finished insulated facade are strictly followed. Headquarters of Koelner S.A. ul. Kwidzyńska Wrocław, POLAND tel fax Distributor 8
ETA-07/0291 of 30/06/2014. European Technical Assessment. Draft. General Part. Technical Assessment Body issuing the. Instytut Techniki Budowlanej
25 INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 22) 825-04-71 (+48 22) 825-76-55 fax: (+48 22) 825-52-86 www.itb.pl Draft Designated according to Article 29 of Regulation (EU)
More informationDeclaration of Performance
Declaration of Performance DoP-07/0291-KI-10M 1. Unique identification code of the product-type: KI-10M The photo depicts an example of a product of the given type of goods 2. Intended use/es: general
More informationHTR-P / HTR-M Insulation fastener
Insulation fastener Anchor version HTR-P HTR-M Benefits - Best in class setting comfort and surface finish - Productivity increase - Heat transmission class 0 W/K due to screw made of high performance
More informationBRAND NEW PRODUCTS 2010
BRAND NEW PRODUCTS 2010 Professional building solution stomixtherm PRIMA External contact thermal insulation system using the polystyrene insulation boards Base clean, without dust and grease, firm, coherent
More informationEuropean Technical Assessment. ETA-13/0088 of 20/03/2018. Egzemplarz archiwalny. General Part. Instytut Techniki Budowlanej
INSTYTUT TECHNIKI BUDOWLANEJ PL 00-611 WARSZAWA ul. Filtrowa 1 tel.: (+48 22) 825-04-71 (+48 22) 825-76-55 fax: (+48 22) 825-52-86 www.itb.pl Designated according to Article 29 of Regulation (EU) No 305/2011
More informationData Sheet 3611 Englisch
Englisch ETICS Mineral Wool Lamella Insulation Board 3611 WDVS Steinlamellen-Dämmplatte 3611 MW-L 041 WAP, non-combustible, blunt edges, pre-coated on both sides Properties Nichtbrennbar (non-combustible),
More informationTechnical Data Sheet
Technical Data Sheet ProGUARD Concrete Insulated Sheathing Specifications & Installation Table Of Contents Product Description... pg. 1 Basic Use... pg. 1 Exterior Finishes... pg. 1 Standard Sizes... pg.
More informationWHATEVER THE CHALLENGE, PHILLIPS HAS YOU COVERED.
WHATEVER THE CHALLENGE, PHILLIPS HAS YOU COVERED. Build walls and ceilings with a strong base, sturdy reinforcements and much more with Phillips extensive line of high quality products. As a single source
More informationPlanning and installation instructions
Planning and installation instructions Stofix Oy Ahlmaninkatu 2 E 40100 Jyväskylä Finland stofixgroup@stofix.com www.stofix.com 2 PLANNING AND INSTALLATION INSTRUCTIONS... 1 1 General... 3 2 Project Design...
More informationGlasboard Liners. installation details. Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels
Glasboard Liners installation details Installation Guide for Glasbord Fibreglass Reinforced Plastic (FRP) panels PLEASE READ ALL INSTRUCTIONS BEFORE BEGINNING INSTALLATION These guidelines are provided
More informationFor system application details, refer to the corresponding Baumit Method Statement before submitting a tender.
SPECIFICATION OF MATERIALS EXTERNAL WALL INSULATION SYSTEM (Adhesively Fixed). For system application details, refer to the corresponding Baumit Method Statement before submitting a tender. Baumit Ltd
More informationManual for Insulating Using the Seamless Thermal Insulation System
Additional info and sale: Sales office: tel. +48 12 289 00 88 fax +48 12 278 28 37 ul. Narutowicza 24 32-020 Wieliczka krakow@fast.zgora.pl Manual for Insulating Using the Seamless Thermal Insulation System
More informationInspection Fundamentals: Stucco & EIFS
Inspection Fundamentals: Stucco & EIFS By Ben Gromicko To be able to identify the stucco system you must understand system components. You should understand the basic components of the most common stucco
More informationCaparol System PRO Data sheet
System features Expanded polystyrene insulation Cost effective solution Excellent detailing options Proven technology Wide variety of colours Reliable protection and crack resistance Proven track record
More informationExternal Steel Stud and Top Hat Walls. Details SYSTEMS 176 NON-FIRE RATED SYSTEMS 176 FIRE RATED SYSTEMS 178 BRICK VENEER SYSTEMS 183 INSTALLATION 185
Details SYSTEMS 176 NON-FIRE RATED SYSTEMS 176 FIRE RATED SYSTEMS 178 BRICK VENEER SYSTEMS 183 INSTALLATION 185 GENERAL REQUIREMENTS 185 FRAMING 185 PLASTERBOARD LAYOUT 189 PLASTERBOARD FIXING 190 EXTERIOR
More informationDUOline. The innovative product line with. More functions More performance More security NEW. fischer DUO - Line. More power, more intelligence
DUOline The innovative product line with More functions More performance More security fischer DUO - Line More power, more intelligence NEW DUO-Line Intelligent combinations for more power and intelligence.
More informationGLASS FIBRE MESH FABRICS. Stronger ideas for a sustainable world ETICS. Marble slab reinforcement. Lightweight construction boards reinforcement
GLASS FIBRE MESH FABRICS Marble slab reinforcement ETICS Mosaic reinforcement Lightweight construction boards reinforcement Profile manufacture Render reinforcement Floor heating mats Stronger ideas for
More informationVENTILATED FACADES. Technical Manual
VENTILATED FACADES Technical Manual Ventilated Facades - Intro TERMS OF BUSINESS AND LEGAL DISCLAIMERS NAMING CONVENTIONS USED IN THE MANUALS FOR TYPICAL APPLICATIONS Hilti strives to achieve continuous
More informationProGUARD Guide Specification
ProGUARD Guide Specification MANUFACTURER Section: 072100 Insulating Sheathing T.Clear Corporation 3255 Symmes Rd. Hamilton, OH 45015 Phone: 800-544-7398 Phone: 513-870-9246 Fax: 513-870-9606 072113 Cementitious
More informationSPECIFICATION GUIDELINE
Environmental StoneWorks specification guideline should be used to assist design professionals in the preparation of projects. Edit and delete items that may not be applicable. Verify all referenced section
More informationfischer termoz SV II ecotwist
fischer termoz SV II ecotwist The innovative countersinkable ETICS fixing for all building material classes. ETA-12/0208 ETAG 014 Use categories A, B, C, D, E We are turning towards your success: With
More informationReal Brick Cladding. Iso Klink Pur. Brick Panel System Catalogue
Iso Klink Pur Brick Panel System Catalogue 1 BRICK CLADDING PANEL SYSTEM Combination of high performance pur insulation and brick cladding, creating durable and aesthetic system which is quick and easy
More informationReal Stone Cladding mm sandstone ashlar. Thin Sandstone Ashlar Catalogue
12 15 20 mm sandstone ashlar Thin Sandstone Ashlar Catalogue 12 15 20 mm ashlar 1 SANDSTONE ASHLAR 12 15 20 MM Ashlar sandstone is the most desired and expensive stone finish for any facade. It is now
More informationDECLARATION OF PERFORMANCE. No EN
DECLARATION OF PERFORMANCE No. 0004 EN 1. Unique identification code of the product-type: 2. Intended use/es: Product Plastic anchors for use in concrete and masonry Intended use/es Screwed-in plastic
More informationData sheet Armatop MP / Page 1
Data sheet Armatop MP / Page 1 Armatop MP Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of ecomin-por, mineral wool, polystyrene and cork exterior
More informationData sheet Armatop A - new / Page 1. Areas of application Bonding Bonding of mineral wool, polystyrene and cork external wall insulation boards.
Data sheet Armatop A - new / Page 1 Armatop A - new Bonding and reinforcing compounds for alsecco external wall systems Areas of application Bonding Bonding of mineral wool, polystyrene and cork external
More informationSPECIFICATION GUIDELINE
SPECIFICATION GUIDELINE Environmental Stoneworks Corporate Office 6300 East Stapleton Drive South Denver, CO 80216 Phone (303) 309-3040 Fax (303) 309-3059 www.estoneworks.com Environmental Stoneworks specification
More informationFOCAL POINT RENDAPANEL TM CLADDING SYSTEM
FOCAL POINT RENDAPANEL TM CLADDING SYSTEM strength and durability SYSTEM INFORMATION & TECHNICAL SPECIFICATION V4 2002 Page 1 of 7 INTRODUCTION Monolithic Light Weight Cement Render Cladding RendaPanel
More informationFaçade panels riveted on an aluminium supporting structure
Ventilated façade 1 General These application instructions are specifically intended for the fastening of large-size EURO PANELS OVERSEAS N.V. façade panels as outside wall cladding on a ventilated and
More informationFor system application details, refer to the corresponding Baumit Method Statement before submitting a tender.
SPECIFICATION OF MATERIALS EXTERNAL WALL INSULATION SYSTEM (Adhesively Fixed). For system application details, refer to the corresponding Baumit Method Statement before submitting a tender. Baumit Ltd
More informationReal Stone Cladding. stone cladding system
Stone Cladding System Catalogue 2015 1 STONE CLADDING SYSTEM Rustic yet elegant natural stone facade suitable for exterior and interior use, at a fraction of cost of traditional walling Easy to install,
More informationMechanical Fixing Systems for External Wall Insulation
Mechanical Fixing Systems for External Wall Insulation Introduction SPSenvirowall insulated render systems are designed to not only improve the insulation and comfort factor of your building, but to also
More informationThe Disclaimer located on the reverse side of the title page of the OAA Rain Penetration Practice Guide applies to each section of the Guide.
Note: This document has been divided into several sections in order to suit the limitations of the website. The Disclaimer located on the reverse side of the title page of the OAA Rain Penetration Practice
More informationTechnical Data Sheet StoLevell Duo plus
Mineral bonding and reinforcing mortar Characteristics Areas of application Properties Exterior and interior For all mineral substrates For bonding insulation boards onto mineral substrates For producing
More informationSystem of Building Profiles PRODUCT CATALOGUE
2011 2012 PRODUCT CATALOGUE Kurim Blansko Germany Poland direction Prague (highway D1) 220 km Brno direction Vienna 150 km direction SVITAVY LIKOV Company direction Olomouc direction Bratislava (highway
More informationVENTILATED FACADES. Technical Manual MFT MFI MFT MFI MFT MFI
VENTILATED FACADES Technical Manual MFT MFI 106 MFT MFI 106 MFT MFI 109 MFT MFI 108 MFT MFI MFT MFI MFT MFI 103 102 104 MFT MFI 107 MFT MFI 105 MFT MFI 101 MFT MFI 105 TERMS OF BUSINESS AND LEGAL DISCLAIMERS
More informationDUOline. The innovative product line with. More functions More performance More security. fischer DUO - Line NEW. More power, more intelligence
DUOline The innovative product line with More functions More performance More security fischer DUO - Line More power, more intelligence NEW DUO-Line Intelligent combinations for more power and intelligence.
More informationBBA 001 Documents included under the scope of BBA s ISO UKAS accreditation
BBA 001 Documents included under the scope of BBA s ISO 17065 UKAS accreditation Product Standard Building Systems and Kits BBA Technical Specification 001 Ceiling Products BBA Technical Specification
More informationEuropean Technical Assessment. ETA-12/0398 of 29/12/2017. General Part. Instytut Techniki Budowlanej. Technical Assessment Body issuing the
European Technical Assessment General Part of 29/12/2017 (English language translation the original version is in Polish language) Body issuing the European Trade name of the construction product Product
More informationmillimetri4 wall system
millimetri4 wall system millimetri4 wall system is a complete wall-cladding system that allows natural stone panels to be dry-joint assembled. Its extreme lightness allows to assemble it on any type of
More informationSept 30, 2004 Page 1 PRODUCT DESCRIPTION PRODUCT FEATURES
Sept 30, 2004 Page 1 PRODUCT FEATURES BASIC USES / RELATED USES LOGIX Insulated Concrete Forms are stackable, interlocking expanded polystyrene (EPS) blocks that serve as permanent formwork to create solid
More informationThe better way to build TM. Installation Manual NAILBASE PANELS
The better way to build TM Installation Manual PANELS November 2018 SIPs Installation Manual Table of Contents Topics General Requirements................................... 3 Materials..............................................
More informationData Sheet 3550 Englisch
Data Sheet 3550 Englisch ETICS Powder Adhesive 3550 WDVS Pulverkleber 3550 mineral adhesive and reinforcing plaster for Brillux ETICS Systems I through VI Properties Mineral adhesive and reinforcing powder.
More informationInsulation. First Revison October DC14 Drainage Mat INSTALLATION GUIDE FOR RESIDENTIAL & COMMERCIAL APPLICATIONS
Insulation First Revison October 2016 DC14 Drainage Mat INSTALLATION GUIDE FOR RESIDENTIAL & COMMERCIAL APPLICATIONS 1. General Information This Guide describes the use of Kingspan GreenGuard DC14 Drainage
More informationInsulated Concrete Forms (ICFs)
Insulated Concrete Forms (ICFs) Cover of Walls & Ceilings Magazine May 2006 ICFs Getting Attention Cover of Construction Dimensions Magazine June 2006 Table of Contents Construction Dimensions Magazine
More informationProudly Made in the U.S.A. 5-Year Warranty. Wayfinding Products
5-Year Warranty Proudly Made in the U.S.A. Wayfinding Products Proudly Made in the U.S.A. Directional Bar Tile surface mount or cast-in-place replaceable (wet-set) Bar Tile and Guide Tile units shall be
More informationFIRESTOP JOINT SPRAY CFS-SP WB. 2mm (0.079") WET FILM ± 7.5 ± 5
Design No. CEJ 27 P (HI/JS 20-05) Table. CONCRETE FLOOR ASSEMBLY: Max. two-hour rated concrete floor assembly made from either lightweight or normal weight concrete with a density of 00-50 pcf, with a
More informationCOATING APPLICATIONS OVER OUTWEAR
COATING APPLICATIONS OVER OUTWEAR PLASTER APPLICATION COATING APPLICATIONS 1 Cover all the joints of. All joints must have tape embedded in the jointing compound. High alkali resistant Joint Tape and Joint
More informationDuPont Tyvek Wall Underlay Install Guide
DuPont Tyvek Wall Underlay Install Guide (For Residential & Light Commercial Buildings) Acceptable Solution to NZBC E2/AS1 New Zealand As at 1/4/15 Version 2 Subject to change without notice DuPont Tyvek
More informationWEIGHT PER PIECE (LBS.)
PRODUCT DESCRIPTION DATA SHEET 04 73 19-US BASIC USE ProGUARD DP is intended to be installed over sheathing and waterproofing over steel or wood studs or over concrete masonry units or poured concrete
More informationEuropean Technical ETA-04/0023 Assessment of 17 October 2017 General Part
European Technical Assessment ETA-04/0023 of 17 October 2017 - Original version in German language General Part Technical Assessment Body issuing the European Technical Assessment: Trade name of the construction
More informationAPPLICATION The Wall areas to be rendered may require a fungicidal wash Ref. ESPS-ALGICID prior to any render applications.
SPS ENVIROWALL LIMITED NBS SPECIFICATION: RENDER ONLY SYSTEM USING RETROBASE BASECOAT WITH REINFORCEMENT MESH USING SILICONE TOPCOAT APPLIED TO EXISTING MASONRY SUBSTRATE M20 EXTERNAL RENDER SYSTEM To
More informationSept 30, 2004 Page 1
Sept 30, 2004 Page 1 This section includes a manufacturer's guide specification for TERRAFOAM EPS building insulation. Refer also to Product Description for detailed product properties, options, and other
More informationInsulating with ZERO.3
Insulating with ZERO.3 An external thermal insulation system is a layer that insulates the outside cladding of a building to improve thermal efficiency. The superior technical characteristics and aesthetic
More informationDesign No. HI/BP PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table 1
FIRESTOP JOINT SPRAY CFS-SP WB SILICONE JOINT SPRAY CFS-SP SIL F-RATING 2-HR. 2-HR. T-RATING -HR. -HR. APPLICATION THICKNESS PERIMETER FIRE BARRIER SYSTEM Hilti, Inc. ASTM E 2307 Table /8" WET FILM (/6"
More informationUsing of ETIC System II Verarbeitung WDV-System II ETICS hard foam insulation boards with mechanical fixation (rail system)
Using of ETIC System II Verarbeitung WDV-System II ETICS hard foam insulation boards with mechanical fixation (rail system) System properties Certified external thermal insulation composite system with
More informationMID-RISE DESIGN & CONSTRUCTION
TECHNICAL BULLETIN No.38-021616 Rev072116 MID-RISE DESIGN & CONSTRUCTION Logix effective R-values range from R-24 to R-28+ Insulated concrete forms (ICF) are becoming a main stream choice for the construction
More informationGypLyner. GypLyner. Metal framed wall lining system. All our systems are covered by SpecSure when using genuine Gyproc and Isover products.
GypLyner GypLyner Metal framed wall lining system All our systems are covered by SpecSure when using genuine Gyproc and Isover products Linings GypLyner GypLyner is a cost-effective, virtually independent
More informationInstallation Guidelines
Installation Guidelines The Vertibreak Wall System: Installation Guidelines Rainscreen Insulation for New or Retrofit Construction Applications Vertibreak rainscreen insulation is an expanded polystyrene
More informationMapefix PE Wall. Chemical anchor for masonry and light loads
Mapefix PE Wall Chemical anchor for masonry and light loads European Technical Approval ETAG 029 M8 M12 AREAS OF USE Mapefix PE Wall is an adhesive for chemically anchoring metal bars in holes made in
More informationAlsecco (U.K.) Ltd THE ALSECCO ECOMIN200 RAIL EXTERNAL WALL INSULATION SYSTEM
CI/SfB (21.9) Rn7 (M2) Alsecco (U.K.) Ltd THE ALSECCO ECOMIN200 RAIL EXTERNAL WALL INSULATION SYSTEM Certificate No 96/3247 DETAIL SHEET 6 Product THIS DETAIL SHEET RELATES TO THE ALSECCO ECOMIN200 RAIL
More informationGeneral building inspectorate approval Z
Deutsches Institut für Bautechnik German Institute of Construction Engineering General approval by the building inspectorate Approval Institute for Construction Products and Methods Construction Engineering
More informationMay 2013 CONSTRUCTION MANUAL
May 2013 CONSTRUCTION MANUAL Table of Contents Limitations... 1 Panel Specification... 2 Facing Material (OSB)... 2 Adhesive Material... 2 Core Material... 2 Panel Weight... 3 Panel Insulation... 3 Panel
More informationCatalogue. ETICS Fixings / E.W.I
Catalogue ETICS Fixings / E.W.I Dear Partners, According to an ancient native American saying, we have not inherited the earth from our parents but are merely borrowing it from our children. This prescient
More informationBUILDING MATERIALS. stone, concrete, ceramics, glass gypsum iron, steel, cast iron, aluminum, copper, titan, metal alloys
BUILDING MATERIALS silicates: metals: natural organic materials: plastics: stone, concrete, ceramics, glass gypsum iron, steel, cast iron, aluminum, copper, titan, metal alloys wood, bamboo, cork, cane,
More informationInstallation Guide. IMPORTANT: Read all sections before starting. For the most up-to-date information, visit our website: leadvisioninternational.
Installation Guide IMPORTANT: Read all sections before starting. For the most up-to-date information, visit our website: leadvisioninternational.com Before installing a composite wall cladding, it is recommended
More informationLIFT-AND-SLIDE DOOR 85 MM INSTALLATION GUIDELINES
Table of Contents Final measurements and assessment of the real building situation... 2 Documentation about the condition of the building and defects... 2 Final measurements of building openings... 2 Planning
More informationBioPrism Solid Surface
Please read all instructions before installing products. STORAGE & HANDLING: Check for damage that may have occurred during transit. Keep receptor flat on pallet, as it was shipped, until ready to install.
More informationEasylationWall. External Wall Insulation System. bringing european innovation
EasylationWall External Wall Insulation System bringing european innovation EasylationWall... the new External Wall Insulation System using brick slips for stunning façades. EXTERNAL WALL INSULATION (EWI)
More informationPolyurethane spray insulation
Polyurethane spray insulation Thermal, acoustic and hydro insulation What makes our products unique? Modern polyurethane (PU) spray foam systems are highly efficient, fast to complete and versatile in
More informationSpecifications for Insulation Board wall and ceiling applications
Specifications for Insulation Board wall and ceiling applications Product Ref: Marmox Multiboard 600mm wide, 1250/2500mm long. 10, 12.5, 20, 30, 40, 50, 60mm thick. Also known as Marmox Board- Pro and
More informationRoofing and Cladding systems overview Prefabricated zinc tiles
Roofing and Cladding systems overview Prefabricated zinc tiles Prefabricated zinc tiles Roofing and Cladding systems overview 3 Index Main characteristics Square tile Rhomboid tile Pointed fish scale tile
More informationmaintenance-free free from painting easy to install Fixing Guide Cedral Click
maintenance-free free from painting easy to install Fixing Guide Cedral Click www.cedralsidings.com CONTENT Step by step guide to installing your Cedral Click façade Required materials and tools 1. Prepare
More informationExterior System installation instructions
Exterior System installation instructions 11/20/14 WPS ES-400 & 500 INSTALLATION INSTRUCTION. The WPS ES-400 & 500 systems Façade panels are designed for use as an external wall cladding in conjunction
More informationAPPLICATION The wall areas to be rendered may require a fungicidal wash Ref. ESPS-ALGICID prior to any render applications.
SPS ENVIROWALL LIMITED NBS SPECIFICATION: RENDER ONLY SYSTEM USING A SURFACE SCRABBLER, SUBSTRATE PRIMER, A C&G BASECOAT WITH REINFORCING MESH AND A SILICONE TOPCOAT APPLIED TO AN EXISTING NON POROUS SUBSTRATE
More informationTechnical Data Sheet StoMiral FL Vario
Fibre-reinforced lightweight base coat in accordance with EN 998-1 Characteristics Areas of application Properties exterior and interior as a lightweight and low-stress base coat (approx. 10 mm) onto even
More informationlindab we simplify construction LindabSandwichPanels Installation instructions Mineral Wool Panels
lindab we simplify construction LindabSandwichPanels Installation instructions Mineral Wool Panels Assembly instructions Handling Receiving of goods Check that the material has not been damaged in transit
More informationEXTERIOR INSULATION FINISHING SYSTEMS. EIFS Alpha System. The House of Scandinavian Finishing Materials
EXTERIOR INSULATION FINISHING SYSTEMS EIFS Alpha System The House of Scandinavian Finishing Materials INTRODUCTION ALPHA SYSTEM As a leader in the production and distribution of environmentally friendly
More informationTechnical data sheet StoLevell Uni
Mineral bonding and reinforcing mortar/base coat Characteristics Areas of application exterior and interior for all mineral and almost all organic substrates for bonding insulation boards and render carrier
More informationREPORT HOLDER: COREV AMERICA BRITTMOORE PARK DRIVE HOUSTON, TEXAS EVALUATION SUBJECT:
0 Most Widely Accepted and Trusted ICC ES Report ICC ES 000 (800) 423 6587 (562) 699 0543 www.icc es.org ESR 2000 Reissued 02/2017 This report is subject to renewal 02/2019. DIVISION: 07 00 00 THERMAL
More informationVertigo Cladding Board
Installation guide Vertigo Cladding Board Geolam: a stunning alternative to wood cladding Vertigo is a composite wood cladding board requiring minimum maintenance. Durable and fade resistant, it will not
More informationThe insulating panel for energy conscious interior renovation. The product. Safe, noticeably better Proved a million times.
The product Safe, noticeably better Proved a million times The insulating panel for energy conscious interior renovation. Necessary tools: Tips for saving heating costs The heating cost shock due to the
More informationProGUARD DP The Game-changing Wall System
ProGUARD DP The Game-changing Wall System Arriscraft ARRIS-stack over ProGUARD DP Insulated Cement Board Panels, using Laticrete MVIS materials. PROGUARD DP INSULATED CONCRETE BOARD, manufactured by T.
More informationSurface Mount Tactile
Proudly Made in the U.S.A. Surface Mount Tactile Surface Mount Tactile Proudly Made in the U.S.A. Surface Mount Tactile Installation Procedure Be sure to read and understand all of these instructions before
More informationfischer fixing compass Solid and hollow brick masonry.
fischer fixing compass Solid and hollow brick masonry. Our fixing specialists for solid and hollow brick masonry. Injection system FIS V The strongest and most flexible solution in masonry. Maximum load-bearing
More informationInsulation boards PhoneStar
Sound Insulation Bavaria Insulation boards PhoneStar Installation instructions Wall Version 15.05. 2015 ONE solution universal in every area PhoneStar is an innovative, very efficient insulation board
More informationFacade panel PICTURA Product Information Sheet
Facade panel PICTURA Product Information Sheet 1 Product range PICTURA fibre cement facade panels are made from: Portland cement Mineral filler Natural organic fibres (cellulose), synthetic organic fibres
More informationEPS Heat insulating composite system
EPS Heat insulating composite system Economical external wall insulation With façade insulation sheets made of styropor Heat insulation and façade creation Proven and cost-effective No heat bridges Baumit
More informationBuilding Construction 14. Dr Nabil El-Sawalhi Associate professor Engineering Projects Management
Building Construction 14 Dr Nabil El-Sawalhi Associate professor Engineering Projects Management Plaster Plaster is a wet mixed material applied to internal walls as a finish to fill in any irregularities
More informationSound-absorbing and sound-insulating barriers
Sound-absorbing and sound-insulating barriers innovative and biocompatible solutions for the environment sound-insulation Sound-absorbing and sound-insulating noise barriers for road and rail traffic are
More informationTABLE OF CONTENTS. 1.0 INTRODUCTION 1.1 Greenstone Structural Engineered Panels 1.2 Drawing and Element Numbers
version 2.5 updated as of 08.04.2017 2 TABLE OF CONTENTS 1.0 INTRODUCTION 1.1 Greenstone Structural Engineered Panels 1.2 Drawing and Element Numbers 2.0 ASSEMBLY 2.1 Sequence of Assembly 2.2 Preparation
More informationWALL CLADDINGS BASIC PRINCIPLES
WALL CLADDINGS BASIC PRINCIPLES Lecturer: Dr Fülöp Zsuzsanna Budapest University of Technology and Economics Faculty of Architecture Engineering Department of Building Constructions www.epszerk.bme.hu
More informationBeginning of the Course
Beginning of the Course Topics we will Cover What is Stucco? What does InterNACHI require? How to Identify Stucco Type. Primary Concerns Related to Stucco. How to Inspect during a Home Inspection. What
More informationINTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES
INTERNATIONAL ASSOCIATION OF PLUMBING AND MECHANICAL OFFICIALS UNIFORM EVALUATION SERVICES EVALUATION CRITERIA FOR ANCHORED MASONRY VENEER SYSTEM WITH POLYSTYRENE FOAM PLASTIC BACKING EC 021-2014 (Adopted
More informationINSULCLAD EXTERIOR CLADDING SYSTEMS
INSULCLAD EXTERIOR CLADDING SYSTEMS INSTALLING INSULCLAD SYSTEMS OVER BRICKWORK AND OTHER MASONRY SUBSTRATES TO BE READ IN CONJUNCTION WITH THE INSULCLAD DESIGN & INSTALLATION MANUAL. THIS INFORMATION
More informationGigaHouse Specifications
GigaCrete Inc. 6775 Speedway Blvd. Suite M105 Las Vegas, NV 89115 Ph (702) 643-6363 Fax (702) 643 1453 www.gigacrete.com GigaHouse Specifications GigaHouse : Factory made highly insulated housing materials
More informationrondo accessories CONTENTS:
rondo accessories SUMMARY Rondo has a range of accessories to complement our steel wall and ceiling systems, which includes Top Hats, Reveal Beads and Angles, as well as a rod bending tool for suspended
More informationMAKING IT STICK: Nails and screws, adhesives and compounds... today contractors have a wide variety of choices.
MAKING IT STICK: Fasteners & Adhesives Walls hold up the building but what holds up the walls? Today contractors have a wide variety of fasteners and adhesives from which to choose, according to the needs
More informationDetail Drawings THE BEST PANEL COMPANY. from. 126 Old Highway 60 East Hardinsburg, Kentucky Office:
Detail Drawings from Rev. 4/2017 126 Old Highway 60 East Hardinsburg, Kentucky 40143 Office: 270-788-3535 www.bestpanelcompany.com Dri-Plane screen / similar / Similar Non-Corrosive Fastener designed to
More information