MC-CG683-ZA76 MC-CG683K-ZP47

Transcription

1 Order No.VCB CE Vacuum Cleaner Model No. MC-CG683-ZC79 MC-CG683-ZA76 MC-CG683K-ZP47 Product Color Destination :Roiyal Blue :Europe TABLE OF CONTENTS PAGE 1 Specifications Location of Controls and Components Troubleshooting Guide Disassembly and Assembly Instructions Dust box cover assembly removal Separate the upper and lower body units Printed circuit board AU (P.C.B. AU) removal Motor removal Cord reel partition unit replacement Rail base U replacement Spring-loaded cord reel pre-winding Wiring Connection Diagram Schematic Diagram Exploded View and Replacement Parts List EXPLODED VIEW (ATTACHMENTS) PARTS LIST (ATTACHMENTS) EXPLODED VIEW (BODY UNIT) PARTS LIST (BODY UNIT) PAGE 7.5. PACKING INSTRUCTIONS PACKING LIST Matsushita Electric Industrial Co., Ltd. All rights reserved. Unauthorized copying and distribution is a violation of law.

2 1 Specifications Model No. MC-CG683 MC-CG683K Power source AC230V~50Hz AC V~50Hz Input power (MAX) 1400W 1400W Input power (IEC) 1200W W Dimensions (WxLxH)mm 280x430x260 Net weight 5.1kg Extension wand Telescopic Crevice nozzle Dusting brush Upholstery nozzle 2

3 2 Location of Controls and Components 3

4 4

5 3 Troubleshooting Guide CONDITION CHECK POINT METHOD OF INSPECTION TRANSACTION Motor fails to rotate (no noise is heard at all) Power supply cord Check power supply cord continuity. If there is no continuity, replace the cord reel patition unit. Fuse of P.C.B. AU (250V, 12A) Check fuse continuity. If there is no continuity, replace P.C.B. AU. Motor continuity Check the conduction between the If there is no continuity, replace the terminals of the motor. motor. ON/OFF Switch Check continuity across switch If there is no continuity, replace connections P.C.B. AU. Triac (Inside of P.C.B.) Check if the triac is in open circuit. If it is in open circuit, replace P.C.B. AU. Motor runs but there is no suction P.C.B. AU Hose or Suction inlet, Extension wand and nozzle Dust bog / Secondary filter Check the internal parts for anything unusual. (burn-out, meltdown, etc.) Check if there is any blockage in the indicated parts. Check if dust bag is full or Secondary filter is choked up. If anything is found unusual, replace the P.C.B. AU with new one. If there is any blockage, remove it. If dust bag is foll, replace with a new one. If Secondary filter is choked up, remove and clean it out or replace. Noise or vibration Motor fan Check dust accumulated in motor fan (it could happen if the vacuum If there is dust accumulated in the motor fan, replace the motor and cleaner has been used without central check filter condition. (never try to filter). dismantle the motor fan) Motor does not change power (runs always at full speed) Power control P.C.B. AU Adjust the power control and check whether or not the resistance varies. (Gray Blue) Examine the triac in the P.C.B. AU and check whether or not T1 and T2 are short-circuited. Motor runs irregularly P.C.B. AU Check possible bad contact of P.C.B. AU. If the resistance does not vary, then replace the P.C.B. AU. If they are short-circuited, then replace the P.C.B. AU. Replace P.C.B. AU. 5

6 4 Disassembly and Assembly Instructions Important notice: Before replacing any components, make sure to turn OFF the vacuum cleaner. Remove the power plug from the outlet. * Caution: 1. Do not attempt to modify the machine, parts, etc. when marking repairs. 2. Even if a wire is partially disconnected, do not attempt to repair and/or connect it when a wired unit is available as service parts. Replace the overall section with a new wired unit. 3. Pull out and/or insert the fastening terminal without twisting it Dust box cover assembly removal 1. Open the dust box cover assembly at an angle of approx. 45. Insert a flat-blade screwdriver between the upper body and the dust box cover assembly and move it in the direction of the arrow mark to remove the dust box cover assembly from its right side Separate the upper and lower body units 1. Remove the five screws fixing the upper body U and lower body U. 2. Remove the screw fixing the upper body U from the rear side. 6

7 3. Lift the upper body U to separate it from the lower body U. 2. Here is the drawing of the lead wire before the P.C.B. AU is removed Printed circuit board AU (P.C.B. AU) removal 1. Remove the Swivel cap unit and Supporter plate U and Switch cover U. 3. Disengage the fast-on terminal of the wires (red) and (blue) which lead to the cord reel partition wall connected to the printed circuit board AU. * Caution: Pull out the fastening terminal without twisting it. Pull out by holding down the section indicated by an arrow. 7

8 4. Remove the P.C.B. AU from the P.C.B. holder Motor removal 1. Remove the dust box lid assembly. (Refer to paragraph 4.1 on P.6) 2. Remove the upper body from the lower body. (Refer to paragraph 4.2 on P.6) 3. Remove the printed circuit board AU. (P.C.B AU) (Refer to paragraph 4.3 on P.7) 4. Remove the two screws fixing the P.C.B. holder and pull it out from the lower body U. 5. Remove the two screws fixing the P.C.B. holder and pull it out from the lower body U. * For removing the printed circuit board AU, first remove the fast-on terminal for the connecting section for the motor. 8

9 5. Lift the motor section from the lower body U. 6. Remove the components fitted to the motor. a. Remove the motor support rubber (rear). b. Remove the motor support rubber (front). c. Remove the motor case plate. d. Remove the thermal protector. e. Remove the motor support front. f. Remove the lead wires connected to the motor. g. Remove the noise suppressor. * Caution: Pull out the fastening terminal of the lead wire connected to the motor unit and thermal protector without twisting it. * Note: When the thermal protector has been replaced, make sure to paste the tape (gasket V) back on the terminals. 9

10 4.5. Cord reel partition unit replacement 1. Increase the gap width between the cord reel and the lower body with a screwdriver. While removing the cord reel shaft from the side of the lower body, lift the cord reel partition unit Rail base U replacement 1. Remove the screw fixing the rail base U onto the cord reel partition U. 2. Remove the rail base U from the cord reel partition U Spring-loaded cord reel prewinding 1. The cord reel partition U has a spring that pre-winds the cord reel. If the cord is not wound, then press the brake arm, and the cord pre-winding will be loosened. If you wish to apply pre-winding again, then wind the cord three turns in the direction of the arrow mark. * If you wish to release the pre-winding, then make sure to hold the cord plug. * For easy removal, pull out the cord slightly, and then lift the cord reel. 10

11 5 Wiring Connection Diagram MODEL MC-CG683 MODEL MC-CG683K 6 Schematic Diagram MODEL MC-CG683 MODEL MC-CG683K 11

12 7 Exploded View and Replacement Parts List 7.1. EXPLODED VIEW (ATTACHMENTS) ) ) )" )# )$ )! 12

13 7.2. PARTS LIST (ATTACHMENTS) Safety Ref No. PART NO. PART NAME & DESCRIPTION Q'TY Remarks A1 AMC94PYL0V0E HOSE ASS'Y 1 A2 AMC99PXL060E EXTENSION WAND UNIT 1 A3 AMV99R6E00EE FLOOR NOZZLE ASS'Y 1 A4 AMC60RUA0V0E CREVICE TOOL 1 Crevice nozzle A5 AMC88RUA0V0E DUSTING BRUSH 1 A6 AMC86RVA000E UPHOLSTERY NOZZLE UNIT 1 13

14 7.3. EXPLODED VIEW (BODY UNIT) *% *' *& *! * * * * * * *% * " *$ *! * # * *! * $ " *$ *! *& * & * % * ' *! *!! *! *!" *!# *' *!% *!$ *! *!' *!& " *! $ % # &! ' 14

15 7.4. PARTS LIST (BODY UNIT) Safety Ref No. PART NO. PART NAME & DESCRIPTION Q'TY Remarks B1 AMV93K6C0ZEE DUST COVER ASS'Y 1 B2 AMV92L6C0ZEE DUST COVER U 1 B3 AMC01DYD0V0E BUCKLE 1 B4 AMC04DYD000E BUCKLE SPRING 1 B5 AMC64HYP0V0E SUCTION INLET PACKING 1 B6 AMC17HYP0V0E AIR INLET PLATE 1 B7 AMC46NYD040E CORD REWIND BUTTON 1 B8 AMC05EYD040E SWITCH PEDAL 1 B9 AMC08EYP000E SWITCH SPRING 2 B10 AMC01BYD030E HANDLE 1 B11 AMC98MYD00EE INDICATOR UNIT 1 B12 AMC32AYD030E FURNITURE GUARD RIGHT 1 B13 AMC30AYD030E FURNITURE GUARD LEFT 1 B14 XTN4+10BFJ TAPPING SCREW 9 B15 AMV98A6C0V0E UPPER BODY UNIT 1 B16 AMC03LYD000E GASKET A 1 B17 AMV75L6D000E GASKET P 1 B18 AMV91N6C00EE CORD REEL PARTITION UNIT 1 B18 AMV91N6C00LE CORD REEL PARTITION UNIT 1 Swiss only B18 AMV91N6C008E CORD REEL PARTITION UNIT 1 UK only B19 AMV98N6C00EE RAIL BASE UNIT 1 B20 AMC23QYD0S0E SWIVEL CAP UNIT 1 B21 AMC85MYP000E SUPPORTER PLATE UNIT 1 B22 AMV89V6C00EE P.C.B.U 1 B23 AMC03EYP000E SWITCH COVER 1 B24 AMV1AV6C000E P.C.B HOLDER AU 1 B25 AMV71L5N000E GASKET K 1 B26 AMV35G4K000E BLACK LEAD WIRE S 1 B27 AMC56L-1800E GASKET V 1 B28 AMV20W4K00EE THERMAL PROTECTOR 1 B29 XTN3+12BFY TAPPING SCREW 2 B30 AMV17F6C000E MOTOR CASE PLATE 1 B31 AMC03FYD000E MOTOR SUPPORT RUBBER (REAR) 1 B32 XTN4+10FFJ TAPPING SCREW 2 B33 AMV07F4K000E MOTOR SUPPORT FRONT 1 B34 AMC99G28000E NOISE SUPPRESSOR 1 B35 AMV92F4K00EE FAN MOTOR UNIT 1 B35 AMV92F4K00CE FAN MOTOR UNIT 1 UK only B36 AMV02F4K000E MOTOR SUPPORT RUBBER FRONT 1 B37 AMC37KYP000E SECONDARY FILTER 1 B38 AMC43KYP0V0E PRE-FILTER 1 B39 AMC-J1EP PAPER BAG (TYPE C-17) 1 B40 AMC10KYD0V0E BAG SUPPORTER 1 B41 AMC34DYP000E SPRING A 1 B42 AMC99CYM0V0E WHEEL 2 B43 AMC97AYD0VBE LOWER BODY UNIT 1 B44 AMC66LYD000E GASKET E 1 B45 AMC67LYD000E GASKET F 1 B46 AMC73KYP000E DUST BOX PACKING 1 B47 AMC93BYD030E HANDLE GRIP UNIT 1 B48 AMC66BYD000E LOWER HANDLE 1 B49 AMC95CYM0V0E CASTER UNIT 1 B50 AMV95KYZ000E FILTER UNIT 1 B51 AMC41KYP0V0E FILTER COVER 1 B52 XTN4+16BFJ TAPPING SCREW 10 B53 XTN4+16BFJK TAPPING SCREW 1 B54 XTN4+25BFY TAPPING SCREW 1 15

16 7.5. PACKING INSTRUCTIONS +$ +# +" +!

17 7.6. PACKING LIST Safety Ref.No Service Parts No. Part Name & Description Q'TY Remarks C1 AMV61Z6C0ZEE CARTON BOX 1 C2 AMV98Z4K00RE CUSHION U 1 C3 AMV90Z4K00RE PARTITION BOARD UNIT 1 C4 AMC69ZYD000E CUSHION A 1 C5 AMC10ZYD000E BODY BAG 1 C6 AMV01Z6C00EE OPERATING INSTRUCTIONS 1 C6 AMV01Z6C008E OPERATING INSTRUCTIONS 1 UK only 17