VEHICLE BODYWORK Detail and groom a vehicle

Transcription

1 1 of 5 level: 2 credit: 4 planned review date: December 2009 sub-field: purpose: entry information: accreditation option: moderation option: Motor Industry People credited with this unit standard are able to: detail exterior of the vehicle; buff, glaze, and polish the vehicle s exterior paintwork; detail vehicle surfaces other than paint; and groom interior of the vehicle. Open. Evaluation of documentation by NZQA and industry. A centrally established and directed national moderation system has been set up by the NZ Motor Industry Training Organisation. special notes: 1 Enactments relevant to this unit standard include but are not limited to Health and Safety in Employment Act 1992; Resource Management Act 1991; local body regulations. 2 Reference to supervisor s requirements means that the supervisor requires that the standard must comply with vehicle preparation standards and requirements determined by the company involved. 3 The practical skills of this standard can be assessed in the workplace or off-job. For the purpose of off-job assessment, the term supervisor means the training provider.

2 2 of 5 Elements and Performance Criteria element 1 Detail exterior of the vehicle. 1.1 Safe working practices are observed throughout the task according to legislative 1.2 Examination of exterior is completed before grooming to enable prior damage to be recorded and particular needs attended to. 1.3 The environment for detailing is selected to ensure that no outside conditions influence or damage the job carried out. 1.4 Exterior is prepared and washed to a standard acceptable to the supervisor. dewax, detergent and sponge or soft bristle brush or steam cleaner. 1.5 Exterior is dried to the supervisor s cotton towelling, chamois. 1.6 Tar, concrete, and paint spots are removed without damage to the paintwork and glass. 1.7 Unwanted panel transfers, logos, and stickers are removed without damage to the paintwork and glass. 1.8 Engine compartment is cleaned to the supervisor s

3 3 of 5 element 2 Buff, glaze, and polish the vehicle s exterior paintwork. 2.1 Safe working practices are observed throughout the task. 2.2 Buffing, glazing, and polishing processes are selected according to the exterior condition. 2.3 Paintwork type is determined according to the vehicle s manufacturer's identification plate. 2.4 Vehicle paint surface finish meets the supervisor s element 3 Detail vehicle surfaces other than paint. 3.1 Safe working practices are observed throughout the task according to legislative 3.2 Vinyl surfaces are cleaned and treated to the supervisor s 3.3 Tyre walls are finished to the supervisor s 3.4 Chrome, stainless steel, alloy, and painted plastics are cleaned and polished to the supervisor s 3.5 Glass components are cleaned to the supervisor s

4 4 of 5 element 4 Groom interior of the vehicle. 4.1 Safe working practices are observed throughout the task according to legislative 4.2 Examination of interior is completed before grooming to ensure that loose items are stored to the satisfaction of the customer. 4.3 Upholstery is cleaned in a manner that prevents damage occurring to coverings. vacuuming, shampoo, dry cleaning. 4.4 Interior is vacuumed to a standard acceptable to the supervisor. 4.5 Stains are removed without damage to the surface. 4.6 Vinyl and plastic surfaces are treated to the supervisor s 4.7 Smell neutralisers are applied to the customer s satisfaction. 4.8 Accessory fittings and controls are in the same position as they were prior to the detailing. Comments on this unit standard Please contact the NZ Motor Industry Training Organisation jlane@mito.org.nz if you wish to suggest changes to the content of this unit standard. Please Note Providers must be accredited by the Qualifications Authority or a delegated interinstitutional body before they can register credits from assessment against unit standards or deliver courses of study leading to that assessment. Industry Training Organisations must be accredited by the Qualifications Authority before they can register credits from assessment against unit standards.

5 5 of 5 Accredited providers and Industry Training Organisations assessing against unit standards must engage with the moderation system that applies to those standards. Accreditation requirements and an outline of the moderation system that applies to this standard are outlined in the Accreditation and Moderation Action Plan (AMAP). The AMAP also includes useful information about special requirements for providers wishing to develop education and training programmes, such as minimum qualifications for tutors and assessors, and special resource This unit standard is covered by AMAP 0014 which can be accessed at