Bracket CHECK: PCL Varies - See Table. System Depth Excluding deck. U Value at 1.5M Centres. 202mm mm 0.16.

Transcription

1 Bracket Top Sheet Cover Width Varies - See Table 30 Varies See Deck Selection Bracket Height Tophat Size Cavity Depth Insulation Thickness Elite System Insulation Value System Depth Excluding deck U Value at 1.5M Centres Nominal Weight/M² Kn 40 RW 140mm 30mm 170mm 170*/180mm λ 202mm kg/m² kg/m² 220mm 30mm 250mm 250mm*/20mm λ 282mm kg/m² 1.28 kg/m² 240mm 30mm 270mm 270mm*/280mm λ 302mm kg/m² 1.84 kg/m² 20mm 30mm 290mm 300mm λ 322mm kg/m² 17.7 kg/m² * Rockwool Cladding Roll only Weight does not include Deck Other u-values by request

2 ELITE SYSTEM SIDE LAP DETAIL ELITE SYSTEM END DETAIL Euroclad SF Steel Quattro bar & bracket depending on U Value requirements 1.2m centres 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat Vapour Control Layer Eurodeck JID JID JID JID or JID Euroclad SF Steel Continuous sheet No End Laps Quattro bar & bracket 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat, Rivets can be replaced with screw fixings if appropriate Vapour Control Layer Eurodeck JID JID JID JID or JID Tophat fixings Rivets are recommended for gauges =/>.7mm mm Self drilling screws recommended for gauges =/>1.25mm Screw fixings specified for tophats can be replaced with rivets if required for aesthetics. Rivets for illustration only. COLOUR SIDE SF Steel Outer Sheet side lap detail

3 Bracket Top Sheet Cover Width Varies - See Table Varies - See Table Varies See Deck Selection Bracket Height Cavity Depth Insulation Thickness Elite System A1 Insulation Value System Depth Excluding deck U Value at 1.5M Centres Nominal Weight/M² Kn 40 RW 140mm 170mm 170mm*/180mm λ 224mm Kg/m² 15.24Kg/m² 220mm 250mm 250mm*/20mm λ 304mm Kg/m² 17.48Kg/m² 240mm 270mm 270mm*/280mm λ 324mm Kg/m² 18.04Kg/m² 20mm 290mm 290mm*/300mm λ 344mm Kg/m² 18.0Kg/m² * Rockwool Cladding Roll only Weight not including deck Other u-values by request

4 ELITE SYSTEM SIDE LAP DETAIL ELITE SYSTEM END LAP DETAIL TOPSHEET DOES NOT END LAP Euroclad SF Steel Quattro bar & bracket depending on U Value requirements 1.2m centres Vapour Control Layer Acoustic Insulation 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat Perforated Eurodeck JID JID JID JID or JID Euroclad SF Steel Continuous sheet No End Laps Quattro bar & bracket Vapour Control Layer Acoustic Insulation 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat, Rivets can be replaced with screw fixings if appropriate Perforated Eurodeck JID JID JID JID or JID Tophat fixings Rivets are recommended for gauges =/>.7mm mm Self drilling screws recommended for gauges =/>1.25mm Screw fixings specified for tophats can be replaced with rivets if required for aesthetics. Rivets for illustration only. COLOUR SIDE SF Steel Outer Sheet side lap detail

5 The distributed load from the external sheet is transferred through the spacer system and tophats to the deck. The tophats as illustrated allow the load to be distributed to each and every deck sheet, avoiding any 1 sheet taking all of the load. It also allows spacer rails to be fitted to the deck in straight rows (rather than diagonal). The use of tophats c400mm long allows for ease of installation on curved roofs. In most cases the maximum spacing achieved will not cause any issues for the external sheet load/span capacity. However, some deck sheets with larger widths will result in centres which may become problematic for the external sheet span ie 1120 wide deck giving centres of 2.240M. In such cases other deck profiles should be considered or the use of longer tophats to allow closer centres for the spacer rails to be achieved. In all cases the external sheet load should be distributed to all deck sheets Quattro bar & bracket Tophats fitted over deck sidelaps in main roof zone. Density increased at perimeters if required. 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat, Rivets can be replaced with screw fixings if appropriate Vapour Control Layer DECK SIDE-LAP VARIES DEPENDING ON DECK VERGE DECK SIDE-LAP DECK RUNNING ACROSS SLOPE Eurodeck JID JID JID JID or JID EAVES Tophat and Rail centres Upslope determined by loadings and deck cover-width. Typically fixed on each deck sheet for approx 2M from eaves & ridge line and then straddling the deck sidelap in main roof zones at 2 x deck coverwidth. Tophat/Bracket centres along rail determined by loading but typically at 1.2M

6 Quattro bar & bracket 25 x 30 x 80 x 30 x 25mm 1.mm galvanised tophat, Rivets can be replaced with screw fixings if appropriate Vapour Control Layer Eurodeck JID JID JID JID or JID VARIES DEPENDING ON LOAD 1200 EAVES

7 EUROCLAD SF mm EXTERNAL SHEET COLOUR SIDE

8 VARIES DEPENDING ON BRACKET HEIGHT 40 VARIES DEPENDING ON BRACKET HEIGHT Brackets less than 20mm require 2 fixings diagonally opposite. Brackets 20mm or more require 4 fixings. < 20mm 20mm

9 ELITE SYSTEMS Eurodeck JID Eurodeck JID Eurodeck JID Eurodeck JID Eurodeck JID

10 Section A-A , , mm coated steel RIDGE SUPPORT SECTION ECSF-RSP A mm Total Length 13 A R

11 54 SMALL FLUTE EAVES FILLER ECSF- EF

12 RIDGE FILLER ECSF-RF Note:Remove slug (part cut crosses) of material prior to instillation to allow for ventilation

13 VERGE SUPPORT SECTION ECSF-V

14 EAVES DRIP ANGLE ECSF-DA 25 50

15 Standard Accessory Clamp. EC SF Clamp 50 ELITE SYSTEMS M8 15mm thread 1m 50 Clamps maximum spacing 1M when connected by a rail